Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 536 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt
new file mode 100644
index 000000000..8f8f95056
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/at91-clock.txt
@@ -0,0 +1,536 @@
+Device Tree Clock bindings for arch-at91
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible : shall be one of the following:
+	"atmel,at91sam9x5-sckc" or
+	"atmel,sama5d4-sckc":
+		at91 SCKC (Slow Clock Controller)
+		This node contains the slow clock definitions.
+
+	"atmel,at91sam9x5-clk-slow-osc":
+		at91 slow oscillator
+
+	"atmel,at91sam9x5-clk-slow-rc-osc":
+		at91 internal slow RC oscillator
+
+	"atmel,<chip>-pmc":
+		at91 PMC (Power Management Controller)
+		All at91 specific clocks (clocks defined below) must be child
+		node of the PMC node.
+		<chip> can be: at91rm9200, at91sam9260, at91sam9261,
+		at91sam9263, at91sam9g45, at91sam9n12, at91sam9rl, at91sam9x5,
+		sama5d2, sama5d3 or sama5d4.
+
+	"atmel,at91sam9x5-clk-slow" (under sckc node)
+	or
+	"atmel,at91sam9260-clk-slow" (under pmc node):
+		at91 slow clk
+
+	"atmel,at91rm9200-clk-main-osc"
+	"atmel,at91sam9x5-clk-main-rc-osc"
+		at91 main clk sources
+
+	"atmel,at91sam9x5-clk-main"
+	"atmel,at91rm9200-clk-main":
+		at91 main clock
+
+	"atmel,at91rm9200-clk-master" or
+	"atmel,at91sam9x5-clk-master":
+		at91 master clock
+
+	"atmel,at91sam9x5-clk-peripheral" or
+	"atmel,at91rm9200-clk-peripheral":
+		at91 peripheral clocks
+
+	"atmel,at91rm9200-clk-pll" or
+	"atmel,at91sam9g45-clk-pll" or
+	"atmel,at91sam9g20-clk-pllb" or
+	"atmel,sama5d3-clk-pll":
+		at91 pll clocks
+
+	"atmel,at91sam9x5-clk-plldiv":
+		at91 plla divisor
+
+	"atmel,at91rm9200-clk-programmable" or
+	"atmel,at91sam9g45-clk-programmable" or
+	"atmel,at91sam9x5-clk-programmable":
+		at91 programmable clocks
+
+	"atmel,at91sam9x5-clk-smd":
+		at91 SMD (Soft Modem) clock
+
+	"atmel,at91rm9200-clk-system":
+		at91 system clocks
+
+	"atmel,at91rm9200-clk-usb" or
+	"atmel,at91sam9x5-clk-usb" or
+	"atmel,at91sam9n12-clk-usb":
+		at91 usb clock
+
+	"atmel,at91sam9x5-clk-utmi":
+		at91 utmi clock
+
+	"atmel,sama5d4-clk-h32mx":
+		at91 h32mx clock
+
+	"atmel,sama5d2-clk-generated":
+		at91 generated clock
+
+	"atmel,sama5d2-clk-audio-pll-frac":
+		at91 audio fractional pll
+
+	"atmel,sama5d2-clk-audio-pll-pad":
+		at91 audio pll CLK_AUDIO output pin
+
+	"atmel,sama5d2-clk-audio-pll-pmc"
+		at91 audio pll output on AUDIOPLLCLK that feeds the PMC
+		and can be used by peripheral clock or generic clock
+
+	"atmel,sama5d2-clk-i2s-mux" (under pmc node):
+		at91 I2S clock source selection
+
+Required properties for SCKC node:
+- reg : defines the IO memory reserved for the SCKC.
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+
+
+For example:
+	sckc: sckc@fffffe50 {
+		compatible = "atmel,sama5d3-pmc";
+		reg = <0xfffffe50 0x4>
+		#size-cells = <0>;
+		#address-cells = <1>;
+
+		/* put at91 slow clocks here */
+	};
+
+
+Required properties for internal slow RC oscillator:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clock-frequency : define the internal RC oscillator frequency.
+
+Optional properties:
+- clock-accuracy : define the internal RC oscillator accuracy.
+
+For example:
+	slow_rc_osc: slow_rc_osc {
+		compatible = "atmel,at91sam9x5-clk-slow-rc-osc";
+		clock-frequency = <32768>;
+		clock-accuracy = <50000000>;
+	};
+
+Required properties for slow oscillator:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall encode the main osc source clk sources (see atmel datasheet).
+
+Optional properties:
+- atmel,osc-bypass : boolean property. Set this when a clock signal is directly
+  provided on XIN.
+
+For example:
+	slow_osc: slow_osc {
+		compatible = "atmel,at91rm9200-clk-slow-osc";
+		#clock-cells = <0>;
+		clocks = <&slow_xtal>;
+	};
+
+Required properties for slow clock:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall encode the slow clk sources (see atmel datasheet).
+
+For example:
+	clk32k: slck {
+		compatible = "atmel,at91sam9x5-clk-slow";
+		#clock-cells = <0>;
+		clocks = <&slow_rc_osc &slow_osc>;
+	};
+
+Required properties for PMC node:
+- reg : defines the IO memory reserved for the PMC.
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- interrupts : shall be set to PMC interrupt line.
+- interrupt-controller : tell that the PMC is an interrupt controller.
+- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id,
+	and reflect the bit position in the PMC_ER/DR/SR registers.
+	You can use the dt macros defined in dt-bindings/clock/at91.h.
+	0 (AT91_PMC_MOSCS) -> main oscillator ready
+	1 (AT91_PMC_LOCKA) -> PLL A ready
+	2 (AT91_PMC_LOCKB) -> PLL B ready
+	3 (AT91_PMC_MCKRDY) -> master clock ready
+	6 (AT91_PMC_LOCKU) -> UTMI PLL clock ready
+	8 .. 15 (AT91_PMC_PCKRDY(id)) -> programmable clock ready
+	16 (AT91_PMC_MOSCSELS) -> main oscillator selected
+	17 (AT91_PMC_MOSCRCS) -> RC main oscillator stabilized
+	18 (AT91_PMC_CFDEV) -> clock failure detected
+
+For example:
+	pmc: pmc@fffffc00 {
+		compatible = "atmel,sama5d3-pmc";
+		interrupts = <1 4 7>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		#size-cells = <0>;
+		#address-cells = <1>;
+
+		/* put at91 clocks here */
+	};
+
+Required properties for main clock internal RC oscillator:
+- interrupts : shall be set to "<0>".
+- clock-frequency : define the internal RC oscillator frequency.
+
+Optional properties:
+- clock-accuracy : define the internal RC oscillator accuracy.
+
+For example:
+	main_rc_osc: main_rc_osc {
+		compatible = "atmel,at91sam9x5-clk-main-rc-osc";
+		interrupt-parent = <&pmc>;
+		interrupts = <0>;
+		clock-frequency = <12000000>;
+		clock-accuracy = <50000000>;
+	};
+
+Required properties for main clock oscillator:
+- interrupts : shall be set to "<0>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall encode the main osc source clk sources (see atmel datasheet).
+
+Optional properties:
+- atmel,osc-bypass : boolean property. Specified if a clock signal is provided
+  on XIN.
+
+  clock signal is directly provided on XIN pin.
+
+For example:
+	main_osc: main_osc {
+		compatible = "atmel,at91rm9200-clk-main-osc";
+		interrupt-parent = <&pmc>;
+		interrupts = <0>;
+		#clock-cells = <0>;
+		clocks = <&main_xtal>;
+	};
+
+Required properties for main clock:
+- interrupts : shall be set to "<0>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall encode the main clk sources (see atmel datasheet).
+
+For example:
+	main: mainck {
+		compatible = "atmel,at91sam9x5-clk-main";
+		interrupt-parent = <&pmc>;
+		interrupts = <0>;
+		#clock-cells = <0>;
+		clocks = <&main_rc_osc &main_osc>;
+	};
+
+Required properties for master clock:
+- interrupts : shall be set to "<3>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the master clock sources (see atmel datasheet) phandles.
+	e.g. "<&ck32k>, <&main>, <&plla>, <&pllb>".
+- atmel,clk-output-range : minimum and maximum clock frequency (two u32
+			   fields).
+	   e.g. output = <0 133000000>; <=> 0 to 133MHz.
+- atmel,clk-divisors : master clock divisors table (four u32 fields).
+		0 <=> reserved value.
+		e.g. divisors = <1 2 4 6>;
+- atmel,master-clk-have-div3-pres : some SoC use the reserved value 7 in the
+				    PRES field as CLOCK_DIV3 (e.g sam9x5).
+
+For example:
+	mck: mck {
+		compatible = "atmel,at91rm9200-clk-master";
+		interrupt-parent = <&pmc>;
+		interrupts = <3>;
+		#clock-cells = <0>;
+		atmel,clk-output-range = <0 133000000>;
+		atmel,clk-divisors = <1 2 4 0>;
+	};
+
+Required properties for peripheral clocks:
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- clocks : shall be the master clock phandle.
+	e.g. clocks = <&mck>;
+- name: device tree node describing a specific peripheral clock.
+	* #clock-cells : from common clock binding; shall be set to 0.
+	* reg: peripheral id. See Atmel's datasheets to get a full
+	  list of peripheral ids.
+	* atmel,clk-output-range : minimum and maximum clock frequency
+	  (two u32 fields). Only valid on at91sam9x5-clk-peripheral
+	  compatible IPs.
+
+For example:
+	periph: periphck {
+		compatible = "atmel,at91sam9x5-clk-peripheral";
+		#size-cells = <0>;
+		#address-cells = <1>;
+		clocks = <&mck>;
+
+		ssc0_clk {
+			#clock-cells = <0>;
+			reg = <2>;
+			atmel,clk-output-range = <0 133000000>;
+		};
+
+		usart0_clk {
+			#clock-cells = <0>;
+			reg = <3>;
+			atmel,clk-output-range = <0 66000000>;
+		};
+	};
+
+
+Required properties for pll clocks:
+- interrupts : shall be set to "<1>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the main clock phandle.
+- reg : pll id.
+	0 -> PLL A
+	1 -> PLL B
+- atmel,clk-input-range : minimum and maximum source clock frequency (two u32
+			  fields).
+	  e.g. input = <1 32000000>; <=> 1 to 32MHz.
+- #atmel,pll-clk-output-range-cells : number of cells reserved for pll output
+				      range description. Sould be set to 2, 3
+				      or 4.
+	* 1st and 2nd cells represent the frequency range (min-max).
+	* 3rd cell is optional and represents the OUT field value for the given
+	  range.
+	* 4th cell is optional and represents the ICPLL field (PLLICPR
+	  register)
+- atmel,pll-clk-output-ranges : pll output frequency ranges + optional parameter
+				depending on #atmel,pll-output-range-cells
+				property value.
+
+For example:
+	plla: pllack {
+		compatible = "atmel,at91sam9g45-clk-pll";
+		interrupt-parent = <&pmc>;
+		interrupts = <1>;
+		#clock-cells = <0>;
+		clocks = <&main>;
+		reg = <0>;
+		atmel,clk-input-range = <2000000 32000000>;
+		#atmel,pll-clk-output-range-cells = <4>;
+		atmel,pll-clk-output-ranges = <74500000 800000000 0 0
+					       69500000 750000000 1 0
+					       64500000 700000000 2 0
+					       59500000 650000000 3 0
+					       54500000 600000000 0 1
+					       49500000 550000000 1 1
+					       44500000 500000000 2 1
+					       40000000 450000000 3 1>;
+	};
+
+Required properties for plldiv clocks (plldiv = pll / 2):
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the plla clock phandle.
+
+The pll divisor is equal to 2 and cannot be changed.
+
+For example:
+	plladiv: plladivck {
+		compatible = "atmel,at91sam9x5-clk-plldiv";
+		#clock-cells = <0>;
+		clocks = <&plla>;
+	};
+
+Required properties for programmable clocks:
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- clocks : shall be the programmable clock source phandles.
+	e.g. clocks = <&clk32k>, <&main>, <&plla>, <&pllb>;
+- name: device tree node describing a specific prog clock.
+	* #clock-cells : from common clock binding; shall be set to 0.
+	* reg : programmable clock id (register offset from  PCKx
+			 register).
+	* interrupts : shall be set to "<(8 + id)>".
+
+For example:
+	prog: progck {
+		compatible = "atmel,at91sam9g45-clk-programmable";
+		#size-cells = <0>;
+		#address-cells = <1>;
+		interrupt-parent = <&pmc>;
+		clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>;
+
+		prog0 {
+			#clock-cells = <0>;
+			reg = <0>;
+			interrupts = <8>;
+		};
+
+		prog1 {
+			#clock-cells = <0>;
+			reg = <1>;
+			interrupts = <9>;
+		};
+	};
+
+
+Required properties for smd clock:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the smd clock source phandles.
+	e.g. clocks = <&plladiv>, <&utmi>;
+
+For example:
+	smd: smdck {
+		compatible = "atmel,at91sam9x5-clk-smd";
+		#clock-cells = <0>;
+		clocks = <&plladiv>, <&utmi>;
+	};
+
+Required properties for system clocks:
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- name: device tree node describing a specific system clock.
+	* #clock-cells : from common clock binding; shall be set to 0.
+	* reg: system clock id (bit position in SCER/SCDR/SCSR registers).
+	      See Atmel's datasheet to get a full list of system clock ids.
+
+For example:
+	system: systemck {
+		compatible = "atmel,at91rm9200-clk-system";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ddrck {
+			#clock-cells = <0>;
+			reg = <2>;
+			clocks = <&mck>;
+		};
+
+		uhpck {
+			#clock-cells = <0>;
+			reg = <6>;
+			clocks = <&usb>;
+		};
+
+		udpck {
+			#clock-cells = <0>;
+			reg = <7>;
+			clocks = <&usb>;
+		};
+	};
+
+
+Required properties for usb clock:
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the smd clock source phandles.
+	e.g. clocks = <&pllb>;
+- atmel,clk-divisors (only available for "atmel,at91rm9200-clk-usb"):
+	usb clock divisor table.
+	e.g. divisors = <1 2 4 0>;
+
+For example:
+	usb: usbck {
+		compatible = "atmel,at91sam9x5-clk-usb";
+		#clock-cells = <0>;
+		clocks = <&plladiv>, <&utmi>;
+	};
+
+	usb: usbck {
+		compatible = "atmel,at91rm9200-clk-usb";
+		#clock-cells = <0>;
+		clocks = <&pllb>;
+		atmel,clk-divisors = <1 2 4 0>;
+	};
+
+
+Required properties for utmi clock:
+- interrupts : shall be set to "<AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>".
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the main clock source phandle.
+
+For example:
+	utmi: utmick {
+		compatible = "atmel,at91sam9x5-clk-utmi";
+		interrupt-parent = <&pmc>;
+		interrupts = <AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>;
+		#clock-cells = <0>;
+		clocks = <&main>;
+	};
+
+Required properties for 32 bits bus Matrix clock (h32mx clock):
+- #clock-cells : from common clock binding; shall be set to 0.
+- clocks : shall be the master clock source phandle.
+
+For example:
+	h32ck: h32mxck {
+		#clock-cells = <0>;
+		compatible = "atmel,sama5d4-clk-h32mx";
+		clocks = <&mck>;
+	};
+
+Required properties for generated clocks:
+- #size-cells : shall be 0 (reg is used to encode clk id).
+- #address-cells : shall be 1 (reg is used to encode clk id).
+- clocks : shall be the generated clock source phandles.
+	e.g. clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>;
+- name: device tree node describing a specific generated clock.
+	* #clock-cells : from common clock binding; shall be set to 0.
+	* reg: peripheral id. See Atmel's datasheets to get a full
+	  list of peripheral ids.
+	* atmel,clk-output-range : minimum and maximum clock frequency
+	  (two u32 fields).
+
+For example:
+	gck {
+		compatible = "atmel,sama5d2-clk-generated";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>;
+
+		tcb0_gclk: tcb0_gclk {
+			#clock-cells = <0>;
+			reg = <35>;
+			atmel,clk-output-range = <0 83000000>;
+		};
+
+		pwm_gclk: pwm_gclk {
+			#clock-cells = <0>;
+			reg = <38>;
+			atmel,clk-output-range = <0 83000000>;
+		};
+	};
+
+Required properties for I2S mux clocks:
+- #size-cells : shall be 0 (reg is used to encode I2S bus id).
+- #address-cells : shall be 1 (reg is used to encode I2S bus id).
+- name: device tree node describing a specific mux clock.
+	* #clock-cells : from common clock binding; shall be set to 0.
+	* clocks : shall be the mux clock parent phandles; shall be 2 phandles:
+	  peripheral and generated clock; the first phandle shall belong to the
+	  peripheral clock and the second one shall belong to the generated
+	  clock; "clock-indices" property can be user to specify
+	  the correct order.
+	* reg: I2S bus id of the corresponding mux clock.
+	  e.g. reg = <0>; for i2s0, reg = <1>; for i2s1
+
+For example:
+	i2s_clkmux {
+		compatible = "atmel,sama5d2-clk-i2s-mux";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2s0muxck: i2s0_muxclk {
+			clocks = <&i2s0_clk>, <&i2s0_gclk>;
+			#clock-cells = <0>;
+			reg = <0>;
+		};
+
+		i2s1muxck: i2s1_muxclk {
+			clocks = <&i2s1_clk>, <&i2s1_gclk>;
+			#clock-cells = <0>;
+			reg = <1>;
+		};
+	};