Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 107 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt
new file mode 100644
index 000000000..b3096421d
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/exynos/samsung-fimd.txt
@@ -0,0 +1,107 @@
+Device-Tree bindings for Samsung SoC display controller (FIMD)
+
+FIMD (Fully Interactive Mobile Display) is the Display Controller for the
+Samsung series of SoCs which transfers the image data from a video memory
+buffer to an external LCD interface.
+
+Required properties:
+- compatible: value should be one of the following
+		"samsung,s3c2443-fimd"; /* for S3C24XX SoCs */
+		"samsung,s3c6400-fimd"; /* for S3C64XX SoCs */
+		"samsung,s5pv210-fimd"; /* for S5PV210 SoC */
+		"samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */
+		"samsung,exynos4210-fimd"; /* for Exynos4 SoCs */
+		"samsung,exynos5250-fimd"; /* for Exynos5250 SoCs */
+		"samsung,exynos5420-fimd"; /* for Exynos5420/5422/5800 SoCs */
+
+- reg: physical base address and length of the FIMD registers set.
+
+- interrupts: should contain a list of all FIMD IP block interrupts in the
+		 order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier
+		 format depends on the interrupt controller used.
+
+- interrupt-names: should contain the interrupt names: "fifo", "vsync",
+	"lcd_sys", in the same order as they were listed in the interrupts
+        property.
+
+- pinctrl-0: pin control group to be used for this controller.
+
+- pinctrl-names: must contain a "default" entry.
+
+- clocks: must include clock specifiers corresponding to entries in the
+         clock-names property.
+
+- clock-names: list of clock names sorted in the same order as the clocks
+               property. Must contain "sclk_fimd" and "fimd".
+
+Optional Properties:
+- power-domains: a phandle to FIMD power domain node.
+- samsung,invert-vden: video enable signal is inverted
+- samsung,invert-vclk: video clock signal is inverted
+- display-timings: timing settings for FIMD, as described in document [1].
+		Can be used in case timings cannot be provided otherwise
+		or to override timings provided by the panel.
+- samsung,sysreg: handle to syscon used to control the system registers
+- i80-if-timings: timing configuration for lcd i80 interface support.
+  - cs-setup: clock cycles for the active period of address signal is enabled
+              until chip select is enabled.
+              If not specified, the default value(0) will be used.
+  - wr-setup: clock cycles for the active period of CS signal is enabled until
+              write signal is enabled.
+              If not specified, the default value(0) will be used.
+  - wr-active: clock cycles for the active period of CS is enabled.
+               If not specified, the default value(1) will be used.
+  - wr-hold: clock cycles for the active period of CS is disabled until write
+             signal is disabled.
+             If not specified, the default value(0) will be used.
+
+  The parameters are defined as:
+
+    VCLK(internal)  __|??????|_____|??????|_____|??????|_____|??????|_____|??
+                      :            :            :            :            :
+    Address Output  --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX
+                      | cs-setup+1 |            :            :            :
+                      |<---------->|            :            :            :
+    Chip Select     ???????????????|____________:____________:____________|??
+                                   | wr-setup+1 |            | wr-hold+1  |
+                                   |<---------->|            |<---------->|
+    Write Enable    ????????????????????????????|____________|???????????????
+                                                | wr-active+1|
+                                                |<---------->|
+    Video Data      ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>--
+
+The device node can contain 'port' child nodes according to the bindings defined
+in [2]. The following are properties specific to those nodes:
+- reg: (required) port index, can be:
+		0 - for CAMIF0 input,
+		1 - for CAMIF1 input,
+		2 - for CAMIF2 input,
+		3 - for parallel output,
+		4 - for write-back interface
+
+[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+SoC specific DT entry:
+
+	fimd@11c00000 {
+		compatible = "samsung,exynos4210-fimd";
+		interrupt-parent = <&combiner>;
+		reg = <0x11c00000 0x20000>;
+		interrupt-names = "fifo", "vsync", "lcd_sys";
+		interrupts = <11 0>, <11 1>, <11 2>;
+		clocks = <&clock 140>, <&clock 283>;
+		clock-names = "sclk_fimd", "fimd";
+		power-domains = <&pd_lcd0>;
+		status = "disabled";
+	};
+
+Board specific DT entry:
+
+	fimd@11c00000 {
+		pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+		pinctrl-names = "default";
+		status = "okay";
+	};