Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

5 files changed, 125 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt
new file mode 100644
index 000000000..28bc5c4d9
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt
@@ -0,0 +1,21 @@
+Maxim thermocouple support
+
+* https://datasheets.maximintegrated.com/en/ds/MAX6675.pdf
+* https://datasheets.maximintegrated.com/en/ds/MAX31855.pdf
+
+Required properties:
+
+	- compatible: must be "maxim,max31855" or "maxim,max6675"
+	- reg: SPI chip select number for the device
+	- spi-max-frequency: must be 4300000
+	- spi-cpha: must be defined for max6675 to enable SPI mode 1
+
+	Refer to spi/spi-bus.txt for generic SPI slave bindings.
+
+Example:
+
+	max31855@0 {
+		compatible = "maxim,max31855";
+		reg = <0>;
+		spi-max-frequency = <4300000>;
+	};
diff --git a/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt b/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt
new file mode 100644
index 000000000..9be57b036
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt
@@ -0,0 +1,24 @@
+* Melexis MLX90614 contactless IR temperature sensor
+
+http://melexis.com/Infrared-Thermometer-Sensors/Infrared-Thermometer-Sensors/MLX90614-615.aspx
+
+Required properties:
+
+  - compatible: should be "melexis,mlx90614"
+  - reg: the I2C address of the sensor
+
+Optional properties:
+
+  - wakeup-gpios: device tree identifier of the GPIO connected to the SDA line
+      to hold low in order to wake up the device.  In normal operation, the
+      GPIO is set as input and will not interfere in I2C communication.  There
+      is no need for a GPIO driving the SCL line.  If no GPIO is given, power
+      management is disabled.
+
+Example:
+
+mlx90614@5a {
+	compatible = "melexis,mlx90614";
+	reg = <0x5a>;
+	wakeup-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+};
diff --git a/Documentation/devicetree/bindings/iio/temperature/mlx90632.txt b/Documentation/devicetree/bindings/iio/temperature/mlx90632.txt
new file mode 100644
index 000000000..0b0581200
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/temperature/mlx90632.txt
@@ -0,0 +1,28 @@
+* Melexis MLX90632 contactless Infra Red temperature sensor
+
+Link to datasheet: https://www.melexis.com/en/documents/documentation/datasheets/datasheet-mlx90632
+
+There are various applications for the Infra Red contactless temperature sensor
+and MLX90632 is most suitable for consumer applications where measured object
+temperature is in range between -20 to 200 degrees Celsius with relative error
+of measurement below 1 degree Celsius in object temperature range for
+industrial applications. Since it can operate and measure ambient temperature
+in range of -20 to 85 degrees Celsius it is suitable also for outdoor use.
+
+Be aware that electronics surrounding the sensor can increase ambient
+temperature. MLX90632 can be calibrated to reduce the housing effect via
+already existing EEPROM parameters.
+
+Since measured object emissivity effects Infra Red energy emitted, emissivity
+should be set before requesting the object temperature.
+
+Required properties:
+  - compatible: should be "melexis,mlx90632"
+  - reg: the I2C address of the sensor (default 0x3a)
+
+Example:
+
+mlx90632@3a {
+	compatible = "melexis,mlx90632";
+	reg = <0x3a>;
+};
diff --git a/Documentation/devicetree/bindings/iio/temperature/tmp007.txt b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt
new file mode 100644
index 000000000..da0af234a
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt
@@ -0,0 +1,33 @@
+* TI TMP007 - IR thermopile sensor with integrated math engine
+
+Link to datasheet: http://www.ti.com/lit/ds/symlink/tmp007.pdf
+
+Required properties:
+
+  - compatible: should be "ti,tmp007"
+  - reg: the I2C address of the sensor (changeable via ADR pins)
+		------------------------------
+		|ADR1 | ADR0 | Device Address|
+		------------------------------
+		   0      0        0x40
+		   0	  1	   0x41
+		   0	 SDA       0x42
+		   0     SCL       0x43
+		   1      0        0x44
+		   1      1        0x45
+		   1	 SDA	   0x46
+		   1     SCL       0x47
+
+Optional properties:
+
+  - interrupts: interrupt mapping for GPIO IRQ (level active low)
+
+Example:
+
+tmp007@40 {
+        compatible = "ti,tmp007";
+        reg = <0x40>;
+	interrupt-parent = <&gpio0>;
+	interrupts = <5 0x08>;
+};
+
diff --git a/Documentation/devicetree/bindings/iio/temperature/tsys01.txt b/Documentation/devicetree/bindings/iio/temperature/tsys01.txt
new file mode 100644
index 000000000..0d5cc5595
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/temperature/tsys01.txt
@@ -0,0 +1,19 @@
+* TSYS01 - Measurement Specialties temperature sensor
+
+Required properties:
+
+	- compatible: should be "meas,tsys01"
+	- reg: I2C address of the sensor (changeable via CSB pin)
+
+		------------------------
+		| CSB | Device Address |
+		------------------------
+		   1         0x76
+		   0	     0x77
+
+Example:
+
+tsys01@76 {
+	compatible = "meas,tsys01";
+	reg = <0x76>;
+};