Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 67 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
new file mode 100644
index 000000000..03025d979
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt
@@ -0,0 +1,67 @@
+Qualcomm QUSB2 phy controller
+=============================
+
+QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets.
+
+Required properties:
+ - compatible: compatible list, contains
+	       "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996,
+	       "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845.
+
+ - reg: offset and length of the PHY register set.
+ - #phy-cells: must be 0.
+
+ - clocks: a list of phandles and clock-specifier pairs,
+	   one for each entry in clock-names.
+ - clock-names: must be "cfg_ahb" for phy config clock,
+			"ref" for 19.2 MHz ref clk,
+			"iface" for phy interface clock (Optional).
+
+ - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
+ - vdda-phy-dpdm-supply: Phandle to 3.1V regulator supply to Dp/Dm port signals.
+
+ - resets: Phandle to reset to phy block.
+
+Optional properties:
+ - nvmem-cells: Phandle to nvmem cell that contains 'HS Tx trim'
+		tuning parameter value for qusb2 phy.
+
+ - qcom,tcsr-syscon: Phandle to TCSR syscon register region.
+ - qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be
+		added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY
+		tuning parameter that may vary for different boards of same SOC.
+		This property is applicable to only QUSB2 v2 PHY (sdm845).
+ - qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX
+		output current.
+		Possible range is - 15mA to 24mA (stepsize of 600 uA).
+		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
+		This property is applicable to only QUSB2 v2 PHY (sdm845).
+		Default value is 22.2mA for sdm845.
+ - qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis level.
+		Possible range is 0 to 15% (stepsize of 5%).
+		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
+		This property is applicable to only QUSB2 v2 PHY (sdm845).
+		Default value is 10% for sdm845.
+- qcom,preemphasis-width: It is a 1 bit value that specifies how long the HSTX
+		pre-emphasis (specified using qcom,preemphasis-level) must be in
+		effect. Duration could be half-bit of full-bit.
+		See dt-bindings/phy/phy-qcom-qusb2.h for applicable values.
+		This property is applicable to only QUSB2 v2 PHY (sdm845).
+		Default value is full-bit width for sdm845.
+
+Example:
+	hsusb_phy: phy@7411000 {
+		compatible = "qcom,msm8996-qusb2-phy";
+		reg = <0x7411000 0x180>;
+		#phy-cells = <0>;
+
+		clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+			<&gcc GCC_RX1_USB2_CLKREF_CLK>,
+		clock-names = "cfg_ahb", "ref";
+
+		vdda-pll-supply = <&pm8994_l12>;
+		vdda-phy-dpdm-supply = <&pm8994_l24>;
+
+		resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+		nvmem-cells = <&qusb2p_hstx_trim>;
+        };