Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 94 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/sound/rt5640.txt b/Documentation/devicetree/bindings/sound/rt5640.txt
new file mode 100644
index 000000000..e40e4893e
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/rt5640.txt
@@ -0,0 +1,94 @@
+RT5640/RT5639 audio CODEC
+
+This device supports I2C only.
+
+Required properties:
+
+- compatible : One of "realtek,rt5640" or "realtek,rt5639".
+
+- reg : The I2C address of the device.
+
+- interrupts : The CODEC's interrupt output.
+
+Optional properties:
+
+- clocks: The phandle of the master clock to the CODEC
+- clock-names: Should be "mclk"
+
+- realtek,in1-differential
+- realtek,in2-differential
+- realtek,in3-differential
+  Boolean. Indicate MIC1/2/3 input are differential, rather than single-ended.
+
+- realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
+
+- realtek,dmic1-data-pin
+  0: dmic1 is not used
+  1: using IN1P pin as dmic1 data pin
+  2: using GPIO3 pin as dmic1 data pin
+
+- realtek,dmic2-data-pin
+  0: dmic2 is not used
+  1: using IN1N pin as dmic2 data pin
+  2: using GPIO4 pin as dmic2 data pin
+
+- realtek,jack-detect-source
+  u32. Valid values:
+  0: jack-detect is not used
+  1: Use GPIO1 for jack-detect
+  2: Use JD1_IN4P for jack-detect
+  3: Use JD2_IN4N for jack-detect
+  4: Use GPIO2 for jack-detect
+  5: Use GPIO3 for jack-detect
+  6: Use GPIO4 for jack-detect
+
+- realtek,jack-detect-not-inverted
+  bool. Normal jack-detect switches give an inverted signal, set this bool
+  in the rare case you've a jack-detect switch which is not inverted.
+
+- realtek,over-current-threshold-microamp
+  u32, micbias over-current detection threshold in µA, valid values are
+  600, 1500 and 2000µA.
+
+- realtek,over-current-scale-factor
+  u32, micbias over-current detection scale-factor, valid values are:
+  0: Scale current by 0.5
+  1: Scale current by 0.75
+  2: Scale current by 1.0
+  3: Scale current by 1.5
+
+Pins on the device (for linking into audio routes) for RT5639/RT5640:
+
+  * DMIC1
+  * DMIC2
+  * MICBIAS1
+  * IN1P
+  * IN1N
+  * IN2P
+  * IN2N
+  * IN3P
+  * IN3N
+  * HPOL
+  * HPOR
+  * LOUTL
+  * LOUTR
+  * SPOLP
+  * SPOLN
+  * SPORP
+  * SPORN
+
+Additional pins on the device for RT5640:
+
+  * MONOP
+  * MONON
+
+Example:
+
+rt5640 {
+	compatible = "realtek,rt5640";
+	reg = <0x1c>;
+	interrupt-parent = <&gpio>;
+	interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>;
+	realtek,ldo1-en-gpios =
+		<&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+};