Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 186 insertions, 0 deletions

diff --git a/Documentation/networking/e100.rst b/Documentation/networking/e100.rst
new file mode 100644
index 000000000..f81111eba
--- /dev/null
+++ b/Documentation/networking/e100.rst
@@ -0,0 +1,186 @@
+==============================================================
+Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
+==============================================================
+
+June 1, 2018
+
+Contents
+========
+
+- In This Release
+- Identifying Your Adapter
+- Building and Installation
+- Driver Configuration Parameters
+- Additional Configurations
+- Known Issues
+- Support
+
+
+In This Release
+===============
+
+This file describes the Linux* Base Driver for the Intel(R) PRO/100 Family of
+Adapters. This driver includes support for Itanium(R)2-based systems.
+
+For questions related to hardware requirements, refer to the documentation
+supplied with your Intel PRO/100 adapter.
+
+The following features are now available in supported kernels:
+ - Native VLANs
+ - Channel Bonding (teaming)
+ - SNMP
+
+Channel Bonding documentation can be found in the Linux kernel source:
+/Documentation/networking/bonding.txt
+
+
+Identifying Your Adapter
+========================
+
+For information on how to identify your adapter, and for the latest Intel
+network drivers, refer to the Intel Support website:
+http://www.intel.com/support
+
+Driver Configuration Parameters
+===============================
+
+The default value for each parameter is generally the recommended setting,
+unless otherwise noted.
+
+Rx Descriptors:
+   Number of receive descriptors. A receive descriptor is a data
+   structure that describes a receive buffer and its attributes to the network
+   controller. The data in the descriptor is used by the controller to write
+   data from the controller to host memory. In the 3.x.x driver the valid range
+   for this parameter is 64-256. The default value is 256. This parameter can be
+   changed using the command::
+
+     ethtool -G eth? rx n
+
+   Where n is the number of desired Rx descriptors.
+
+Tx Descriptors:
+   Number of transmit descriptors. A transmit descriptor is a data
+   structure that describes a transmit buffer and its attributes to the network
+   controller. The data in the descriptor is used by the controller to read
+   data from the host memory to the controller. In the 3.x.x driver the valid
+   range for this parameter is 64-256. The default value is 128. This parameter
+   can be changed using the command::
+
+     ethtool -G eth? tx n
+
+   Where n is the number of desired Tx descriptors.
+
+Speed/Duplex:
+   The driver auto-negotiates the link speed and duplex settings by
+   default. The ethtool utility can be used as follows to force speed/duplex.::
+
+     ethtool -s eth?  autoneg off speed {10|100} duplex {full|half}
+
+   NOTE: setting the speed/duplex to incorrect values will cause the link to
+   fail.
+
+Event Log Message Level:
+   The driver uses the message level flag to log events
+   to syslog. The message level can be set at driver load time. It can also be
+   set using the command::
+
+     ethtool -s eth? msglvl n
+
+
+Additional Configurations
+=========================
+
+Configuring the Driver on Different Distributions
+-------------------------------------------------
+
+Configuring a network driver to load properly when the system is started
+is distribution dependent.  Typically, the configuration process involves
+adding an alias line to `/etc/modprobe.d/*.conf` as well as editing other
+system startup scripts and/or configuration files.  Many popular Linux
+distributions ship with tools to make these changes for you.  To learn
+the proper way to configure a network device for your system, refer to
+your distribution documentation.  If during this process you are asked
+for the driver or module name, the name for the Linux Base Driver for
+the Intel PRO/100 Family of Adapters is e100.
+
+As an example, if you install the e100 driver for two PRO/100 adapters
+(eth0 and eth1), add the following to a configuration file in
+/etc/modprobe.d/::
+
+       alias eth0 e100
+       alias eth1 e100
+
+Viewing Link Messages
+---------------------
+
+In order to see link messages and other Intel driver information on your
+console, you must set the dmesg level up to six.  This can be done by
+entering the following on the command line before loading the e100
+driver::
+
+       dmesg -n 6
+
+If you wish to see all messages issued by the driver, including debug
+messages, set the dmesg level to eight.
+
+NOTE: This setting is not saved across reboots.
+
+ethtool
+-------
+
+The driver utilizes the ethtool interface for driver configuration and
+diagnostics, as well as displaying statistical information.  The ethtool
+version 1.6 or later is required for this functionality.
+
+The latest release of ethtool can be found from
+https://www.kernel.org/pub/software/network/ethtool/
+
+Enabling Wake on LAN* (WoL)
+---------------------------
+WoL is provided through the ethtool* utility.  For instructions on
+enabling WoL with ethtool, refer to the ethtool man page.  WoL will be
+enabled on the system during the next shut down or reboot.  For this
+driver version, in order to enable WoL, the e100 driver must be loaded
+when shutting down or rebooting the system.
+
+NAPI
+----
+
+NAPI (Rx polling mode) is supported in the e100 driver.
+
+See https://wiki.linuxfoundation.org/networking/napi for more
+information on NAPI.
+
+Multiple Interfaces on Same Ethernet Broadcast Network
+------------------------------------------------------
+
+Due to the default ARP behavior on Linux, it is not possible to have one
+system on two IP networks in the same Ethernet broadcast domain
+(non-partitioned switch) behave as expected.  All Ethernet interfaces
+will respond to IP traffic for any IP address assigned to the system.
+This results in unbalanced receive traffic.
+
+If you have multiple interfaces in a server, either turn on ARP
+filtering by
+
+(1) entering::
+
+	echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
+
+    (this only works if your kernel's version is higher than 2.4.5), or
+
+(2) installing the interfaces in separate broadcast domains (either
+    in different switches or in a switch partitioned to VLANs).
+
+
+Support
+=======
+For general information, go to the Intel support website at:
+http://www.intel.com/support/
+
+or the Intel Wired Networking project hosted by Sourceforge at:
+http://sourceforge.net/projects/e1000
+If an issue is identified with the released source code on a supported kernel
+with a supported adapter, email the specific information related to the issue
+to e1000-devel@lists.sf.net.