Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 245 insertions, 0 deletions

diff --git a/drivers/gpio/gpio-max730x.c b/drivers/gpio/gpio-max730x.c
new file mode 100644
index 000000000..198a36b07
--- /dev/null
+++ b/drivers/gpio/gpio-max730x.c
@@ -0,0 +1,245 @@
+/**
+ * Copyright (C) 2006 Juergen Beisert, Pengutronix
+ * Copyright (C) 2008 Guennadi Liakhovetski, Pengutronix
+ * Copyright (C) 2009 Wolfram Sang, Pengutronix
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * The Maxim MAX7300/1 device is an I2C/SPI driven GPIO expander. There are
+ * 28 GPIOs. 8 of them can trigger an interrupt. See datasheet for more
+ * details
+ * Note:
+ * - DIN must be stable at the rising edge of clock.
+ * - when writing:
+ *   - always clock in 16 clocks at once
+ *   - at DIN: D15 first, D0 last
+ *   - D0..D7 = databyte, D8..D14 = commandbyte
+ *   - D15 = low -> write command
+ * - when reading
+ *   - always clock in 16 clocks at once
+ *   - at DIN: D15 first, D0 last
+ *   - D0..D7 = dummy, D8..D14 = register address
+ *   - D15 = high -> read command
+ *   - raise CS and assert it again
+ *   - always clock in 16 clocks at once
+ *   - at DOUT: D15 first, D0 last
+ *   - D0..D7 contains the data from the first cycle
+ *
+ * The driver exports a standard gpiochip interface
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include <linux/spi/max7301.h>
+#include <linux/gpio/driver.h>
+#include <linux/slab.h>
+
+/*
+ * Pin configurations, see MAX7301 datasheet page 6
+ */
+#define PIN_CONFIG_MASK 0x03
+#define PIN_CONFIG_IN_PULLUP 0x03
+#define PIN_CONFIG_IN_WO_PULLUP 0x02
+#define PIN_CONFIG_OUT 0x01
+
+#define PIN_NUMBER 28
+
+static int max7301_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	struct max7301 *ts = gpiochip_get_data(chip);
+	u8 *config;
+	u8 offset_bits, pin_config;
+	int ret;
+
+	/* First 4 pins are unused in the controller */
+	offset += 4;
+	offset_bits = (offset & 3) << 1;
+
+	config = &ts->port_config[offset >> 2];
+
+	if (ts->input_pullup_active & BIT(offset))
+		pin_config = PIN_CONFIG_IN_PULLUP;
+	else
+		pin_config = PIN_CONFIG_IN_WO_PULLUP;
+
+	mutex_lock(&ts->lock);
+
+	*config = (*config & ~(PIN_CONFIG_MASK << offset_bits))
+			   | (pin_config << offset_bits);
+
+	ret = ts->write(ts->dev, 0x08 + (offset >> 2), *config);
+
+	mutex_unlock(&ts->lock);
+
+	return ret;
+}
+
+static int __max7301_set(struct max7301 *ts, unsigned offset, int value)
+{
+	if (value) {
+		ts->out_level |= 1 << offset;
+		return ts->write(ts->dev, 0x20 + offset, 0x01);
+	} else {
+		ts->out_level &= ~(1 << offset);
+		return ts->write(ts->dev, 0x20 + offset, 0x00);
+	}
+}
+
+static int max7301_direction_output(struct gpio_chip *chip, unsigned offset,
+				    int value)
+{
+	struct max7301 *ts = gpiochip_get_data(chip);
+	u8 *config;
+	u8 offset_bits;
+	int ret;
+
+	/* First 4 pins are unused in the controller */
+	offset += 4;
+	offset_bits = (offset & 3) << 1;
+
+	config = &ts->port_config[offset >> 2];
+
+	mutex_lock(&ts->lock);
+
+	*config = (*config & ~(PIN_CONFIG_MASK << offset_bits))
+			   | (PIN_CONFIG_OUT << offset_bits);
+
+	ret = __max7301_set(ts, offset, value);
+
+	if (!ret)
+		ret = ts->write(ts->dev, 0x08 + (offset >> 2), *config);
+
+	mutex_unlock(&ts->lock);
+
+	return ret;
+}
+
+static int max7301_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct max7301 *ts = gpiochip_get_data(chip);
+	int config, level = -EINVAL;
+
+	/* First 4 pins are unused in the controller */
+	offset += 4;
+
+	mutex_lock(&ts->lock);
+
+	config = (ts->port_config[offset >> 2] >> ((offset & 3) << 1))
+			& PIN_CONFIG_MASK;
+
+	switch (config) {
+	case PIN_CONFIG_OUT:
+		/* Output: return cached level */
+		level =  !!(ts->out_level & (1 << offset));
+		break;
+	case PIN_CONFIG_IN_WO_PULLUP:
+	case PIN_CONFIG_IN_PULLUP:
+		/* Input: read out */
+		level = ts->read(ts->dev, 0x20 + offset) & 0x01;
+	}
+	mutex_unlock(&ts->lock);
+
+	return level;
+}
+
+static void max7301_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct max7301 *ts = gpiochip_get_data(chip);
+
+	/* First 4 pins are unused in the controller */
+	offset += 4;
+
+	mutex_lock(&ts->lock);
+
+	__max7301_set(ts, offset, value);
+
+	mutex_unlock(&ts->lock);
+}
+
+int __max730x_probe(struct max7301 *ts)
+{
+	struct device *dev = ts->dev;
+	struct max7301_platform_data *pdata;
+	int i, ret;
+
+	pdata = dev_get_platdata(dev);
+
+	mutex_init(&ts->lock);
+	dev_set_drvdata(dev, ts);
+
+	/* Power up the chip and disable IRQ output */
+	ts->write(dev, 0x04, 0x01);
+
+	if (pdata) {
+		ts->input_pullup_active = pdata->input_pullup_active;
+		ts->chip.base = pdata->base;
+	} else {
+		ts->chip.base = -1;
+	}
+	ts->chip.label = dev->driver->name;
+
+	ts->chip.direction_input = max7301_direction_input;
+	ts->chip.get = max7301_get;
+	ts->chip.direction_output = max7301_direction_output;
+	ts->chip.set = max7301_set;
+
+	ts->chip.ngpio = PIN_NUMBER;
+	ts->chip.can_sleep = true;
+	ts->chip.parent = dev;
+	ts->chip.owner = THIS_MODULE;
+
+	ret = gpiochip_add_data(&ts->chip, ts);
+	if (ret)
+		goto exit_destroy;
+
+	/*
+	 * initialize pullups according to platform data and cache the
+	 * register values for later use.
+	 */
+	for (i = 1; i < 8; i++) {
+		int j;
+		/*
+		 * initialize port_config with "0xAA", which means
+		 * input with internal pullup disabled. This is needed
+		 * to avoid writing zeros (in the inner for loop),
+		 * which is not allowed according to the datasheet.
+		 */
+		ts->port_config[i] = 0xAA;
+		for (j = 0; j < 4; j++) {
+			int offset = (i - 1) * 4 + j;
+			ret = max7301_direction_input(&ts->chip, offset);
+			if (ret)
+				goto exit_destroy;
+		}
+	}
+
+	return ret;
+
+exit_destroy:
+	mutex_destroy(&ts->lock);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(__max730x_probe);
+
+int __max730x_remove(struct device *dev)
+{
+	struct max7301 *ts = dev_get_drvdata(dev);
+
+	if (ts == NULL)
+		return -ENODEV;
+
+	/* Power down the chip and disable IRQ output */
+	ts->write(dev, 0x04, 0x00);
+	gpiochip_remove(&ts->chip);
+	mutex_destroy(&ts->lock);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(__max730x_remove);
+
+MODULE_AUTHOR("Juergen Beisert, Wolfram Sang");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("MAX730x GPIO-Expanders, generic parts");