Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 360 insertions, 0 deletions

diff --git a/drivers/i2c/busses/i2c-designware-common.c b/drivers/i2c/busses/i2c-designware-common.c
new file mode 100644
index 000000000..69ec4a791
--- /dev/null
+++ b/drivers/i2c/busses/i2c-designware-common.c
@@ -0,0 +1,360 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Synopsys DesignWare I2C adapter driver.
+ *
+ * Based on the TI DAVINCI I2C adapter driver.
+ *
+ * Copyright (C) 2006 Texas Instruments.
+ * Copyright (C) 2007 MontaVista Software Inc.
+ * Copyright (C) 2009 Provigent Ltd.
+ */
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/export.h>
+#include <linux/errno.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/pm_runtime.h>
+#include <linux/swab.h>
+
+#include "i2c-designware-core.h"
+
+static char *abort_sources[] = {
+	[ABRT_7B_ADDR_NOACK] =
+		"slave address not acknowledged (7bit mode)",
+	[ABRT_10ADDR1_NOACK] =
+		"first address byte not acknowledged (10bit mode)",
+	[ABRT_10ADDR2_NOACK] =
+		"second address byte not acknowledged (10bit mode)",
+	[ABRT_TXDATA_NOACK] =
+		"data not acknowledged",
+	[ABRT_GCALL_NOACK] =
+		"no acknowledgement for a general call",
+	[ABRT_GCALL_READ] =
+		"read after general call",
+	[ABRT_SBYTE_ACKDET] =
+		"start byte acknowledged",
+	[ABRT_SBYTE_NORSTRT] =
+		"trying to send start byte when restart is disabled",
+	[ABRT_10B_RD_NORSTRT] =
+		"trying to read when restart is disabled (10bit mode)",
+	[ABRT_MASTER_DIS] =
+		"trying to use disabled adapter",
+	[ARB_LOST] =
+		"lost arbitration",
+	[ABRT_SLAVE_FLUSH_TXFIFO] =
+		"read command so flush old data in the TX FIFO",
+	[ABRT_SLAVE_ARBLOST] =
+		"slave lost the bus while transmitting data to a remote master",
+	[ABRT_SLAVE_RD_INTX] =
+		"incorrect slave-transmitter mode configuration",
+};
+
+u32 dw_readl(struct dw_i2c_dev *dev, int offset)
+{
+	u32 value;
+
+	if (dev->flags & ACCESS_16BIT)
+		value = readw_relaxed(dev->base + offset) |
+			(readw_relaxed(dev->base + offset + 2) << 16);
+	else
+		value = readl_relaxed(dev->base + offset);
+
+	if (dev->flags & ACCESS_SWAP)
+		return swab32(value);
+	else
+		return value;
+}
+
+void dw_writel(struct dw_i2c_dev *dev, u32 b, int offset)
+{
+	if (dev->flags & ACCESS_SWAP)
+		b = swab32(b);
+
+	if (dev->flags & ACCESS_16BIT) {
+		writew_relaxed((u16)b, dev->base + offset);
+		writew_relaxed((u16)(b >> 16), dev->base + offset + 2);
+	} else {
+		writel_relaxed(b, dev->base + offset);
+	}
+}
+
+/**
+ * i2c_dw_set_reg_access() - Set register access flags
+ * @dev: device private data
+ *
+ * Autodetects needed register access mode and sets access flags accordingly.
+ * This must be called before doing any other register access.
+ */
+int i2c_dw_set_reg_access(struct dw_i2c_dev *dev)
+{
+	u32 reg;
+	int ret;
+
+	ret = i2c_dw_acquire_lock(dev);
+	if (ret)
+		return ret;
+
+	reg = dw_readl(dev, DW_IC_COMP_TYPE);
+	i2c_dw_release_lock(dev);
+
+	if (reg == swab32(DW_IC_COMP_TYPE_VALUE)) {
+		/* Configure register endianess access */
+		dev->flags |= ACCESS_SWAP;
+	} else if (reg == (DW_IC_COMP_TYPE_VALUE & 0x0000ffff)) {
+		/* Configure register access mode 16bit */
+		dev->flags |= ACCESS_16BIT;
+	} else if (reg != DW_IC_COMP_TYPE_VALUE) {
+		dev_err(dev->dev,
+			"Unknown Synopsys component type: 0x%08x\n", reg);
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
+u32 i2c_dw_scl_hcnt(u32 ic_clk, u32 tSYMBOL, u32 tf, int cond, int offset)
+{
+	/*
+	 * DesignWare I2C core doesn't seem to have solid strategy to meet
+	 * the tHD;STA timing spec.  Configuring _HCNT based on tHIGH spec
+	 * will result in violation of the tHD;STA spec.
+	 */
+	if (cond)
+		/*
+		 * Conditional expression:
+		 *
+		 *   IC_[FS]S_SCL_HCNT + (1+4+3) >= IC_CLK * tHIGH
+		 *
+		 * This is based on the DW manuals, and represents an ideal
+		 * configuration.  The resulting I2C bus speed will be
+		 * faster than any of the others.
+		 *
+		 * If your hardware is free from tHD;STA issue, try this one.
+		 */
+		return (ic_clk * tSYMBOL + 500000) / 1000000 - 8 + offset;
+	else
+		/*
+		 * Conditional expression:
+		 *
+		 *   IC_[FS]S_SCL_HCNT + 3 >= IC_CLK * (tHD;STA + tf)
+		 *
+		 * This is just experimental rule; the tHD;STA period turned
+		 * out to be proportinal to (_HCNT + 3).  With this setting,
+		 * we could meet both tHIGH and tHD;STA timing specs.
+		 *
+		 * If unsure, you'd better to take this alternative.
+		 *
+		 * The reason why we need to take into account "tf" here,
+		 * is the same as described in i2c_dw_scl_lcnt().
+		 */
+		return (ic_clk * (tSYMBOL + tf) + 500000) / 1000000
+			- 3 + offset;
+}
+
+u32 i2c_dw_scl_lcnt(u32 ic_clk, u32 tLOW, u32 tf, int offset)
+{
+	/*
+	 * Conditional expression:
+	 *
+	 *   IC_[FS]S_SCL_LCNT + 1 >= IC_CLK * (tLOW + tf)
+	 *
+	 * DW I2C core starts counting the SCL CNTs for the LOW period
+	 * of the SCL clock (tLOW) as soon as it pulls the SCL line.
+	 * In order to meet the tLOW timing spec, we need to take into
+	 * account the fall time of SCL signal (tf).  Default tf value
+	 * should be 0.3 us, for safety.
+	 */
+	return ((ic_clk * (tLOW + tf) + 500000) / 1000000) - 1 + offset;
+}
+
+int i2c_dw_set_sda_hold(struct dw_i2c_dev *dev)
+{
+	u32 reg;
+	int ret;
+
+	ret = i2c_dw_acquire_lock(dev);
+	if (ret)
+		return ret;
+
+	/* Configure SDA Hold Time if required */
+	reg = dw_readl(dev, DW_IC_COMP_VERSION);
+	if (reg >= DW_IC_SDA_HOLD_MIN_VERS) {
+		if (!dev->sda_hold_time) {
+			/* Keep previous hold time setting if no one set it */
+			dev->sda_hold_time = dw_readl(dev, DW_IC_SDA_HOLD);
+		}
+
+		/*
+		 * Workaround for avoiding TX arbitration lost in case I2C
+		 * slave pulls SDA down "too quickly" after falling egde of
+		 * SCL by enabling non-zero SDA RX hold. Specification says it
+		 * extends incoming SDA low to high transition while SCL is
+		 * high but it apprears to help also above issue.
+		 */
+		if (!(dev->sda_hold_time & DW_IC_SDA_HOLD_RX_MASK))
+			dev->sda_hold_time |= 1 << DW_IC_SDA_HOLD_RX_SHIFT;
+
+		dev_dbg(dev->dev, "SDA Hold Time TX:RX = %d:%d\n",
+			dev->sda_hold_time & ~(u32)DW_IC_SDA_HOLD_RX_MASK,
+			dev->sda_hold_time >> DW_IC_SDA_HOLD_RX_SHIFT);
+	} else if (dev->sda_hold_time) {
+		dev_warn(dev->dev,
+			"Hardware too old to adjust SDA hold time.\n");
+		dev->sda_hold_time = 0;
+	}
+
+	i2c_dw_release_lock(dev);
+
+	return 0;
+}
+
+void __i2c_dw_disable(struct dw_i2c_dev *dev)
+{
+	int timeout = 100;
+
+	do {
+		__i2c_dw_disable_nowait(dev);
+		/*
+		 * The enable status register may be unimplemented, but
+		 * in that case this test reads zero and exits the loop.
+		 */
+		if ((dw_readl(dev, DW_IC_ENABLE_STATUS) & 1) == 0)
+			return;
+
+		/*
+		 * Wait 10 times the signaling period of the highest I2C
+		 * transfer supported by the driver (for 400KHz this is
+		 * 25us) as described in the DesignWare I2C databook.
+		 */
+		usleep_range(25, 250);
+	} while (timeout--);
+
+	dev_warn(dev->dev, "timeout in disabling adapter\n");
+}
+
+unsigned long i2c_dw_clk_rate(struct dw_i2c_dev *dev)
+{
+	/*
+	 * Clock is not necessary if we got LCNT/HCNT values directly from
+	 * the platform code.
+	 */
+	if (WARN_ON_ONCE(!dev->get_clk_rate_khz))
+		return 0;
+	return dev->get_clk_rate_khz(dev);
+}
+
+int i2c_dw_prepare_clk(struct dw_i2c_dev *dev, bool prepare)
+{
+	if (IS_ERR(dev->clk))
+		return PTR_ERR(dev->clk);
+
+	if (prepare)
+		return clk_prepare_enable(dev->clk);
+
+	clk_disable_unprepare(dev->clk);
+	return 0;
+}
+EXPORT_SYMBOL_GPL(i2c_dw_prepare_clk);
+
+int i2c_dw_acquire_lock(struct dw_i2c_dev *dev)
+{
+	int ret;
+
+	if (!dev->acquire_lock)
+		return 0;
+
+	ret = dev->acquire_lock(dev);
+	if (!ret)
+		return 0;
+
+	dev_err(dev->dev, "couldn't acquire bus ownership\n");
+
+	return ret;
+}
+
+void i2c_dw_release_lock(struct dw_i2c_dev *dev)
+{
+	if (dev->release_lock)
+		dev->release_lock(dev);
+}
+
+/*
+ * Waiting for bus not busy
+ */
+int i2c_dw_wait_bus_not_busy(struct dw_i2c_dev *dev)
+{
+	int timeout = TIMEOUT;
+
+	while (dw_readl(dev, DW_IC_STATUS) & DW_IC_STATUS_ACTIVITY) {
+		if (timeout <= 0) {
+			dev_warn(dev->dev, "timeout waiting for bus ready\n");
+			i2c_recover_bus(&dev->adapter);
+
+			if (dw_readl(dev, DW_IC_STATUS) & DW_IC_STATUS_ACTIVITY)
+				return -ETIMEDOUT;
+			return 0;
+		}
+		timeout--;
+		usleep_range(1000, 1100);
+	}
+
+	return 0;
+}
+
+int i2c_dw_handle_tx_abort(struct dw_i2c_dev *dev)
+{
+	unsigned long abort_source = dev->abort_source;
+	int i;
+
+	if (abort_source & DW_IC_TX_ABRT_NOACK) {
+		for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources))
+			dev_dbg(dev->dev,
+				"%s: %s\n", __func__, abort_sources[i]);
+		return -EREMOTEIO;
+	}
+
+	for_each_set_bit(i, &abort_source, ARRAY_SIZE(abort_sources))
+		dev_err(dev->dev, "%s: %s\n", __func__, abort_sources[i]);
+
+	if (abort_source & DW_IC_TX_ARB_LOST)
+		return -EAGAIN;
+	else if (abort_source & DW_IC_TX_ABRT_GCALL_READ)
+		return -EINVAL; /* wrong msgs[] data */
+	else
+		return -EIO;
+}
+
+u32 i2c_dw_func(struct i2c_adapter *adap)
+{
+	struct dw_i2c_dev *dev = i2c_get_adapdata(adap);
+
+	return dev->functionality;
+}
+
+void i2c_dw_disable(struct dw_i2c_dev *dev)
+{
+	/* Disable controller */
+	__i2c_dw_disable(dev);
+
+	/* Disable all interupts */
+	dw_writel(dev, 0, DW_IC_INTR_MASK);
+	dw_readl(dev, DW_IC_CLR_INTR);
+}
+
+void i2c_dw_disable_int(struct dw_i2c_dev *dev)
+{
+	dw_writel(dev, 0, DW_IC_INTR_MASK);
+}
+
+u32 i2c_dw_read_comp_param(struct dw_i2c_dev *dev)
+{
+	return dw_readl(dev, DW_IC_COMP_PARAM_1);
+}
+EXPORT_SYMBOL_GPL(i2c_dw_read_comp_param);
+
+MODULE_DESCRIPTION("Synopsys DesignWare I2C bus adapter core");
+MODULE_LICENSE("GPL");