Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 679 insertions, 0 deletions

diff --git a/drivers/mtd/devices/lart.c b/drivers/mtd/devices/lart.c
new file mode 100644
index 000000000..f67b653c1
--- /dev/null
+++ b/drivers/mtd/devices/lart.c
@@ -0,0 +1,679 @@
+
+/*
+ * MTD driver for the 28F160F3 Flash Memory (non-CFI) on LART.
+ *
+ * Author: Abraham vd Merwe <abraham@2d3d.co.za>
+ *
+ * Copyright (c) 2001, 2d3D, Inc.
+ *
+ * This code is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * References:
+ *
+ *    [1] 3 Volt Fast Boot Block Flash Memory" Intel Datasheet
+ *           - Order Number: 290644-005
+ *           - January 2000
+ *
+ *    [2] MTD internal API documentation
+ *           - http://www.linux-mtd.infradead.org/ 
+ *
+ * Limitations:
+ *
+ *    Even though this driver is written for 3 Volt Fast Boot
+ *    Block Flash Memory, it is rather specific to LART. With
+ *    Minor modifications, notably the without data/address line
+ *    mangling and different bus settings, etc. it should be
+ *    trivial to adapt to other platforms.
+ *
+ *    If somebody would sponsor me a different board, I'll
+ *    adapt the driver (:
+ */
+
+/* debugging */
+//#define LART_DEBUG
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/string.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+#ifndef CONFIG_SA1100_LART
+#error This is for LART architecture only
+#endif
+
+static char module_name[] = "lart";
+
+/*
+ * These values is specific to 28Fxxxx3 flash memory.
+ * See section 2.3.1 in "3 Volt Fast Boot Block Flash Memory" Intel Datasheet
+ */
+#define FLASH_BLOCKSIZE_PARAM		(4096 * BUSWIDTH)
+#define FLASH_NUMBLOCKS_16m_PARAM	8
+#define FLASH_NUMBLOCKS_8m_PARAM	8
+
+/*
+ * These values is specific to 28Fxxxx3 flash memory.
+ * See section 2.3.2 in "3 Volt Fast Boot Block Flash Memory" Intel Datasheet
+ */
+#define FLASH_BLOCKSIZE_MAIN		(32768 * BUSWIDTH)
+#define FLASH_NUMBLOCKS_16m_MAIN	31
+#define FLASH_NUMBLOCKS_8m_MAIN		15
+
+/*
+ * These values are specific to LART
+ */
+
+/* general */
+#define BUSWIDTH			4				/* don't change this - a lot of the code _will_ break if you change this */
+#define FLASH_OFFSET		0xe8000000		/* see linux/arch/arm/mach-sa1100/lart.c */
+
+/* blob */
+#define NUM_BLOB_BLOCKS		FLASH_NUMBLOCKS_16m_PARAM
+#define PART_BLOB_START		0x00000000
+#define PART_BLOB_LEN		(NUM_BLOB_BLOCKS * FLASH_BLOCKSIZE_PARAM)
+
+/* kernel */
+#define NUM_KERNEL_BLOCKS	7
+#define PART_KERNEL_START	(PART_BLOB_START + PART_BLOB_LEN)
+#define PART_KERNEL_LEN		(NUM_KERNEL_BLOCKS * FLASH_BLOCKSIZE_MAIN)
+
+/* initial ramdisk */
+#define NUM_INITRD_BLOCKS	24
+#define PART_INITRD_START	(PART_KERNEL_START + PART_KERNEL_LEN)
+#define PART_INITRD_LEN		(NUM_INITRD_BLOCKS * FLASH_BLOCKSIZE_MAIN)
+
+/*
+ * See section 4.0 in "3 Volt Fast Boot Block Flash Memory" Intel Datasheet
+ */
+#define READ_ARRAY			0x00FF00FF		/* Read Array/Reset */
+#define READ_ID_CODES		0x00900090		/* Read Identifier Codes */
+#define ERASE_SETUP			0x00200020		/* Block Erase */
+#define ERASE_CONFIRM		0x00D000D0		/* Block Erase and Program Resume */
+#define PGM_SETUP			0x00400040		/* Program */
+#define STATUS_READ			0x00700070		/* Read Status Register */
+#define STATUS_CLEAR		0x00500050		/* Clear Status Register */
+#define STATUS_BUSY			0x00800080		/* Write State Machine Status (WSMS) */
+#define STATUS_ERASE_ERR	0x00200020		/* Erase Status (ES) */
+#define STATUS_PGM_ERR		0x00100010		/* Program Status (PS) */
+
+/*
+ * See section 4.2 in "3 Volt Fast Boot Block Flash Memory" Intel Datasheet
+ */
+#define FLASH_MANUFACTURER			0x00890089
+#define FLASH_DEVICE_8mbit_TOP		0x88f188f1
+#define FLASH_DEVICE_8mbit_BOTTOM	0x88f288f2
+#define FLASH_DEVICE_16mbit_TOP		0x88f388f3
+#define FLASH_DEVICE_16mbit_BOTTOM	0x88f488f4
+
+/***************************************************************************************************/
+
+/*
+ * The data line mapping on LART is as follows:
+ *
+ *   	 U2  CPU |   U3  CPU
+ *   	 -------------------
+ *   	  0  20  |   0   12
+ *   	  1  22  |   1   14
+ *   	  2  19  |   2   11
+ *   	  3  17  |   3   9
+ *   	  4  24  |   4   0
+ *   	  5  26  |   5   2
+ *   	  6  31  |   6   7
+ *   	  7  29  |   7   5
+ *   	  8  21  |   8   13
+ *   	  9  23  |   9   15
+ *   	  10 18  |   10  10
+ *   	  11 16  |   11  8
+ *   	  12 25  |   12  1
+ *   	  13 27  |   13  3
+ *   	  14 30  |   14  6
+ *   	  15 28  |   15  4
+ */
+
+/* Mangle data (x) */
+#define DATA_TO_FLASH(x)				\
+	(									\
+		(((x) & 0x08009000) >> 11)	+	\
+		(((x) & 0x00002000) >> 10)	+	\
+		(((x) & 0x04004000) >> 8)	+	\
+		(((x) & 0x00000010) >> 4)	+	\
+		(((x) & 0x91000820) >> 3)	+	\
+		(((x) & 0x22080080) >> 2)	+	\
+		((x) & 0x40000400)			+	\
+		(((x) & 0x00040040) << 1)	+	\
+		(((x) & 0x00110000) << 4)	+	\
+		(((x) & 0x00220100) << 5)	+	\
+		(((x) & 0x00800208) << 6)	+	\
+		(((x) & 0x00400004) << 9)	+	\
+		(((x) & 0x00000001) << 12)	+	\
+		(((x) & 0x00000002) << 13)		\
+	)
+
+/* Unmangle data (x) */
+#define FLASH_TO_DATA(x)				\
+	(									\
+		(((x) & 0x00010012) << 11)	+	\
+		(((x) & 0x00000008) << 10)	+	\
+		(((x) & 0x00040040) << 8)	+	\
+		(((x) & 0x00000001) << 4)	+	\
+		(((x) & 0x12200104) << 3)	+	\
+		(((x) & 0x08820020) << 2)	+	\
+		((x) & 0x40000400)			+	\
+		(((x) & 0x00080080) >> 1)	+	\
+		(((x) & 0x01100000) >> 4)	+	\
+		(((x) & 0x04402000) >> 5)	+	\
+		(((x) & 0x20008200) >> 6)	+	\
+		(((x) & 0x80000800) >> 9)	+	\
+		(((x) & 0x00001000) >> 12)	+	\
+		(((x) & 0x00004000) >> 13)		\
+	)
+
+/*
+ * The address line mapping on LART is as follows:
+ *
+ *   	 U3  CPU |   U2  CPU
+ *   	 -------------------
+ *   	  0  2   |   0   2
+ *   	  1  3   |   1   3
+ *   	  2  9   |   2   9
+ *   	  3  13  |   3   8
+ *   	  4  8   |   4   7
+ *   	  5  12  |   5   6
+ *   	  6  11  |   6   5
+ *   	  7  10  |   7   4
+ *   	  8  4   |   8   10
+ *   	  9  5   |   9   11
+ *   	 10  6   |   10  12
+ *   	 11  7   |   11  13
+ *
+ *   	 BOOT BLOCK BOUNDARY
+ *
+ *   	 12  15  |   12  15
+ *   	 13  14  |   13  14
+ *   	 14  16  |   14  16
+ *
+ *   	 MAIN BLOCK BOUNDARY
+ *
+ *   	 15  17  |   15  18
+ *   	 16  18  |   16  17
+ *   	 17  20  |   17  20
+ *   	 18  19  |   18  19
+ *   	 19  21  |   19  21
+ *
+ * As we can see from above, the addresses aren't mangled across
+ * block boundaries, so we don't need to worry about address
+ * translations except for sending/reading commands during
+ * initialization
+ */
+
+/* Mangle address (x) on chip U2 */
+#define ADDR_TO_FLASH_U2(x)				\
+	(									\
+		(((x) & 0x00000f00) >> 4)	+	\
+		(((x) & 0x00042000) << 1)	+	\
+		(((x) & 0x0009c003) << 2)	+	\
+		(((x) & 0x00021080) << 3)	+	\
+		(((x) & 0x00000010) << 4)	+	\
+		(((x) & 0x00000040) << 5)	+	\
+		(((x) & 0x00000024) << 7)	+	\
+		(((x) & 0x00000008) << 10)		\
+	)
+
+/* Unmangle address (x) on chip U2 */
+#define FLASH_U2_TO_ADDR(x)				\
+	(									\
+		(((x) << 4) & 0x00000f00)	+	\
+		(((x) >> 1) & 0x00042000)	+	\
+		(((x) >> 2) & 0x0009c003)	+	\
+		(((x) >> 3) & 0x00021080)	+	\
+		(((x) >> 4) & 0x00000010)	+	\
+		(((x) >> 5) & 0x00000040)	+	\
+		(((x) >> 7) & 0x00000024)	+	\
+		(((x) >> 10) & 0x00000008)		\
+	)
+
+/* Mangle address (x) on chip U3 */
+#define ADDR_TO_FLASH_U3(x)				\
+	(									\
+		(((x) & 0x00000080) >> 3)	+	\
+		(((x) & 0x00000040) >> 1)	+	\
+		(((x) & 0x00052020) << 1)	+	\
+		(((x) & 0x00084f03) << 2)	+	\
+		(((x) & 0x00029010) << 3)	+	\
+		(((x) & 0x00000008) << 5)	+	\
+		(((x) & 0x00000004) << 7)		\
+	)
+
+/* Unmangle address (x) on chip U3 */
+#define FLASH_U3_TO_ADDR(x)				\
+	(									\
+		(((x) << 3) & 0x00000080)	+	\
+		(((x) << 1) & 0x00000040)	+	\
+		(((x) >> 1) & 0x00052020)	+	\
+		(((x) >> 2) & 0x00084f03)	+	\
+		(((x) >> 3) & 0x00029010)	+	\
+		(((x) >> 5) & 0x00000008)	+	\
+		(((x) >> 7) & 0x00000004)		\
+	)
+
+/***************************************************************************************************/
+
+static __u8 read8 (__u32 offset)
+{
+   volatile __u8 *data = (__u8 *) (FLASH_OFFSET + offset);
+#ifdef LART_DEBUG
+   printk (KERN_DEBUG "%s(): 0x%.8x -> 0x%.2x\n", __func__, offset, *data);
+#endif
+   return (*data);
+}
+
+static __u32 read32 (__u32 offset)
+{
+   volatile __u32 *data = (__u32 *) (FLASH_OFFSET + offset);
+#ifdef LART_DEBUG
+   printk (KERN_DEBUG "%s(): 0x%.8x -> 0x%.8x\n", __func__, offset, *data);
+#endif
+   return (*data);
+}
+
+static void write32 (__u32 x,__u32 offset)
+{
+   volatile __u32 *data = (__u32 *) (FLASH_OFFSET + offset);
+   *data = x;
+#ifdef LART_DEBUG
+   printk (KERN_DEBUG "%s(): 0x%.8x <- 0x%.8x\n", __func__, offset, *data);
+#endif
+}
+
+/***************************************************************************************************/
+
+/*
+ * Probe for 16mbit flash memory on a LART board without doing
+ * too much damage. Since we need to write 1 dword to memory,
+ * we're f**cked if this happens to be DRAM since we can't
+ * restore the memory (otherwise we might exit Read Array mode).
+ *
+ * Returns 1 if we found 16mbit flash memory on LART, 0 otherwise.
+ */
+static int flash_probe (void)
+{
+   __u32 manufacturer,devtype;
+
+   /* setup "Read Identifier Codes" mode */
+   write32 (DATA_TO_FLASH (READ_ID_CODES),0x00000000);
+
+   /* probe U2. U2/U3 returns the same data since the first 3
+	* address lines is mangled in the same way */
+   manufacturer = FLASH_TO_DATA (read32 (ADDR_TO_FLASH_U2 (0x00000000)));
+   devtype = FLASH_TO_DATA (read32 (ADDR_TO_FLASH_U2 (0x00000001)));
+
+   /* put the flash back into command mode */
+   write32 (DATA_TO_FLASH (READ_ARRAY),0x00000000);
+
+   return (manufacturer == FLASH_MANUFACTURER && (devtype == FLASH_DEVICE_16mbit_TOP || devtype == FLASH_DEVICE_16mbit_BOTTOM));
+}
+
+/*
+ * Erase one block of flash memory at offset ``offset'' which is any
+ * address within the block which should be erased.
+ *
+ * Returns 1 if successful, 0 otherwise.
+ */
+static inline int erase_block (__u32 offset)
+{
+   __u32 status;
+
+#ifdef LART_DEBUG
+   printk (KERN_DEBUG "%s(): 0x%.8x\n", __func__, offset);
+#endif
+
+   /* erase and confirm */
+   write32 (DATA_TO_FLASH (ERASE_SETUP),offset);
+   write32 (DATA_TO_FLASH (ERASE_CONFIRM),offset);
+
+   /* wait for block erase to finish */
+   do
+	 {
+		write32 (DATA_TO_FLASH (STATUS_READ),offset);
+		status = FLASH_TO_DATA (read32 (offset));
+	 }
+   while ((~status & STATUS_BUSY) != 0);
+
+   /* put the flash back into command mode */
+   write32 (DATA_TO_FLASH (READ_ARRAY),offset);
+
+   /* was the erase successful? */
+   if ((status & STATUS_ERASE_ERR))
+	 {
+		printk (KERN_WARNING "%s: erase error at address 0x%.8x.\n",module_name,offset);
+		return (0);
+	 }
+
+   return (1);
+}
+
+static int flash_erase (struct mtd_info *mtd,struct erase_info *instr)
+{
+   __u32 addr,len;
+   int i,first;
+
+#ifdef LART_DEBUG
+   printk (KERN_DEBUG "%s(addr = 0x%.8x, len = %d)\n", __func__, instr->addr, instr->len);
+#endif
+
+   /*
+	* check that both start and end of the requested erase are
+	* aligned with the erasesize at the appropriate addresses.
+	*
+	* skip all erase regions which are ended before the start of
+	* the requested erase. Actually, to save on the calculations,
+	* we skip to the first erase region which starts after the
+	* start of the requested erase, and then go back one.
+	*/
+   for (i = 0; i < mtd->numeraseregions && instr->addr >= mtd->eraseregions[i].offset; i++) ;
+   i--;
+
+   /*
+	* ok, now i is pointing at the erase region in which this
+	* erase request starts. Check the start of the requested
+	* erase range is aligned with the erase size which is in
+	* effect here.
+	*/
+   if (i < 0 || (instr->addr & (mtd->eraseregions[i].erasesize - 1)))
+      return -EINVAL;
+
+   /* Remember the erase region we start on */
+   first = i;
+
+   /*
+	* next, check that the end of the requested erase is aligned
+	* with the erase region at that address.
+	*
+	* as before, drop back one to point at the region in which
+	* the address actually falls
+	*/
+   for (; i < mtd->numeraseregions && instr->addr + instr->len >= mtd->eraseregions[i].offset; i++) ;
+   i--;
+
+   /* is the end aligned on a block boundary? */
+   if (i < 0 || ((instr->addr + instr->len) & (mtd->eraseregions[i].erasesize - 1)))
+      return -EINVAL;
+
+   addr = instr->addr;
+   len = instr->len;
+
+   i = first;
+
+   /* now erase those blocks */
+   while (len)
+	 {
+		if (!erase_block (addr))
+			 return (-EIO);
+
+		addr += mtd->eraseregions[i].erasesize;
+		len -= mtd->eraseregions[i].erasesize;
+
+		if (addr == mtd->eraseregions[i].offset + (mtd->eraseregions[i].erasesize * mtd->eraseregions[i].numblocks)) i++;
+	 }
+
+   return (0);
+}
+
+static int flash_read (struct mtd_info *mtd,loff_t from,size_t len,size_t *retlen,u_char *buf)
+{
+#ifdef LART_DEBUG
+   printk (KERN_DEBUG "%s(from = 0x%.8x, len = %d)\n", __func__, (__u32)from, len);
+#endif
+
+   /* we always read len bytes */
+   *retlen = len;
+
+   /* first, we read bytes until we reach a dword boundary */
+   if (from & (BUSWIDTH - 1))
+	 {
+		int gap = BUSWIDTH - (from & (BUSWIDTH - 1));
+
+		while (len && gap--) *buf++ = read8 (from++), len--;
+	 }
+
+   /* now we read dwords until we reach a non-dword boundary */
+   while (len >= BUSWIDTH)
+	 {
+		*((__u32 *) buf) = read32 (from);
+
+		buf += BUSWIDTH;
+		from += BUSWIDTH;
+		len -= BUSWIDTH;
+	 }
+
+   /* top up the last unaligned bytes */
+   if (len & (BUSWIDTH - 1))
+	 while (len--) *buf++ = read8 (from++);
+
+   return (0);
+}
+
+/*
+ * Write one dword ``x'' to flash memory at offset ``offset''. ``offset''
+ * must be 32 bits, i.e. it must be on a dword boundary.
+ *
+ * Returns 1 if successful, 0 otherwise.
+ */
+static inline int write_dword (__u32 offset,__u32 x)
+{
+   __u32 status;
+
+#ifdef LART_DEBUG
+   printk (KERN_DEBUG "%s(): 0x%.8x <- 0x%.8x\n", __func__, offset, x);
+#endif
+
+   /* setup writing */
+   write32 (DATA_TO_FLASH (PGM_SETUP),offset);
+
+   /* write the data */
+   write32 (x,offset);
+
+   /* wait for the write to finish */
+   do
+	 {
+		write32 (DATA_TO_FLASH (STATUS_READ),offset);
+		status = FLASH_TO_DATA (read32 (offset));
+	 }
+   while ((~status & STATUS_BUSY) != 0);
+
+   /* put the flash back into command mode */
+   write32 (DATA_TO_FLASH (READ_ARRAY),offset);
+
+   /* was the write successful? */
+   if ((status & STATUS_PGM_ERR) || read32 (offset) != x)
+	 {
+		printk (KERN_WARNING "%s: write error at address 0x%.8x.\n",module_name,offset);
+		return (0);
+	 }
+
+   return (1);
+}
+
+static int flash_write (struct mtd_info *mtd,loff_t to,size_t len,size_t *retlen,const u_char *buf)
+{
+   __u8 tmp[4];
+   int i,n;
+
+#ifdef LART_DEBUG
+   printk (KERN_DEBUG "%s(to = 0x%.8x, len = %d)\n", __func__, (__u32)to, len);
+#endif
+
+   /* sanity checks */
+   if (!len) return (0);
+
+   /* first, we write a 0xFF.... padded byte until we reach a dword boundary */
+   if (to & (BUSWIDTH - 1))
+	 {
+		__u32 aligned = to & ~(BUSWIDTH - 1);
+		int gap = to - aligned;
+
+		i = n = 0;
+
+		while (gap--) tmp[i++] = 0xFF;
+		while (len && i < BUSWIDTH) tmp[i++] = buf[n++], len--;
+		while (i < BUSWIDTH) tmp[i++] = 0xFF;
+
+		if (!write_dword (aligned,*((__u32 *) tmp))) return (-EIO);
+
+		to += n;
+		buf += n;
+		*retlen += n;
+	 }
+
+   /* now we write dwords until we reach a non-dword boundary */
+   while (len >= BUSWIDTH)
+	 {
+		if (!write_dword (to,*((__u32 *) buf))) return (-EIO);
+
+		to += BUSWIDTH;
+		buf += BUSWIDTH;
+		*retlen += BUSWIDTH;
+		len -= BUSWIDTH;
+	 }
+
+   /* top up the last unaligned bytes, padded with 0xFF.... */
+   if (len & (BUSWIDTH - 1))
+	 {
+		i = n = 0;
+
+		while (len--) tmp[i++] = buf[n++];
+		while (i < BUSWIDTH) tmp[i++] = 0xFF;
+
+		if (!write_dword (to,*((__u32 *) tmp))) return (-EIO);
+
+		*retlen += n;
+	 }
+
+   return (0);
+}
+
+/***************************************************************************************************/
+
+static struct mtd_info mtd;
+
+static struct mtd_erase_region_info erase_regions[] = {
+	/* parameter blocks */
+	{
+		.offset		= 0x00000000,
+		.erasesize	= FLASH_BLOCKSIZE_PARAM,
+		.numblocks	= FLASH_NUMBLOCKS_16m_PARAM,
+	},
+	/* main blocks */
+	{
+		.offset	 = FLASH_BLOCKSIZE_PARAM * FLASH_NUMBLOCKS_16m_PARAM,
+		.erasesize	= FLASH_BLOCKSIZE_MAIN,
+		.numblocks	= FLASH_NUMBLOCKS_16m_MAIN,
+	}
+};
+
+static const struct mtd_partition lart_partitions[] = {
+	/* blob */
+	{
+		.name	= "blob",
+		.offset	= PART_BLOB_START,
+		.size	= PART_BLOB_LEN,
+	},
+	/* kernel */
+	{
+		.name	= "kernel",
+		.offset	= PART_KERNEL_START,	/* MTDPART_OFS_APPEND */
+		.size	= PART_KERNEL_LEN,
+	},
+	/* initial ramdisk / file system */
+	{
+		.name	= "file system",
+		.offset	= PART_INITRD_START,	/* MTDPART_OFS_APPEND */
+		.size	= PART_INITRD_LEN,	/* MTDPART_SIZ_FULL */
+	}
+};
+#define NUM_PARTITIONS ARRAY_SIZE(lart_partitions)
+
+static int __init lart_flash_init (void)
+{
+   int result;
+   memset (&mtd,0,sizeof (mtd));
+   printk ("MTD driver for LART. Written by Abraham vd Merwe <abraham@2d3d.co.za>\n");
+   printk ("%s: Probing for 28F160x3 flash on LART...\n",module_name);
+   if (!flash_probe ())
+	 {
+		printk (KERN_WARNING "%s: Found no LART compatible flash device\n",module_name);
+		return (-ENXIO);
+	 }
+   printk ("%s: This looks like a LART board to me.\n",module_name);
+   mtd.name = module_name;
+   mtd.type = MTD_NORFLASH;
+   mtd.writesize = 1;
+   mtd.writebufsize = 4;
+   mtd.flags = MTD_CAP_NORFLASH;
+   mtd.size = FLASH_BLOCKSIZE_PARAM * FLASH_NUMBLOCKS_16m_PARAM + FLASH_BLOCKSIZE_MAIN * FLASH_NUMBLOCKS_16m_MAIN;
+   mtd.erasesize = FLASH_BLOCKSIZE_MAIN;
+   mtd.numeraseregions = ARRAY_SIZE(erase_regions);
+   mtd.eraseregions = erase_regions;
+   mtd._erase = flash_erase;
+   mtd._read = flash_read;
+   mtd._write = flash_write;
+   mtd.owner = THIS_MODULE;
+
+#ifdef LART_DEBUG
+   printk (KERN_DEBUG
+		   "mtd.name = %s\n"
+		   "mtd.size = 0x%.8x (%uM)\n"
+		   "mtd.erasesize = 0x%.8x (%uK)\n"
+		   "mtd.numeraseregions = %d\n",
+		   mtd.name,
+		   mtd.size,mtd.size / (1024*1024),
+		   mtd.erasesize,mtd.erasesize / 1024,
+		   mtd.numeraseregions);
+
+   if (mtd.numeraseregions)
+	 for (result = 0; result < mtd.numeraseregions; result++)
+	   printk (KERN_DEBUG
+			   "\n\n"
+			   "mtd.eraseregions[%d].offset = 0x%.8x\n"
+			   "mtd.eraseregions[%d].erasesize = 0x%.8x (%uK)\n"
+			   "mtd.eraseregions[%d].numblocks = %d\n",
+			   result,mtd.eraseregions[result].offset,
+			   result,mtd.eraseregions[result].erasesize,mtd.eraseregions[result].erasesize / 1024,
+			   result,mtd.eraseregions[result].numblocks);
+
+   printk ("\npartitions = %d\n", ARRAY_SIZE(lart_partitions));
+
+   for (result = 0; result < ARRAY_SIZE(lart_partitions); result++)
+	 printk (KERN_DEBUG
+			 "\n\n"
+			 "lart_partitions[%d].name = %s\n"
+			 "lart_partitions[%d].offset = 0x%.8x\n"
+			 "lart_partitions[%d].size = 0x%.8x (%uK)\n",
+			 result,lart_partitions[result].name,
+			 result,lart_partitions[result].offset,
+			 result,lart_partitions[result].size,lart_partitions[result].size / 1024);
+#endif
+
+   result = mtd_device_register(&mtd, lart_partitions,
+                                ARRAY_SIZE(lart_partitions));
+
+   return (result);
+}
+
+static void __exit lart_flash_exit (void)
+{
+   mtd_device_unregister(&mtd);
+}
+
+module_init (lart_flash_init);
+module_exit (lart_flash_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Abraham vd Merwe <abraham@2d3d.co.za>");
+MODULE_DESCRIPTION("MTD driver for Intel 28F160F3 on LART board");