Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1400 insertions, 0 deletions

diff --git a/drivers/net/ethernet/intel/e1000e/80003es2lan.c b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
new file mode 100644
index 000000000..257bd59bc
--- /dev/null
+++ b/drivers/net/ethernet/intel/e1000e/80003es2lan.c
@@ -0,0 +1,1400 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright(c) 1999 - 2018 Intel Corporation. */
+
+/* 80003ES2LAN Gigabit Ethernet Controller (Copper)
+ * 80003ES2LAN Gigabit Ethernet Controller (Serdes)
+ */
+
+#include "e1000.h"
+
+/* A table for the GG82563 cable length where the range is defined
+ * with a lower bound at "index" and the upper bound at
+ * "index + 5".
+ */
+static const u16 e1000_gg82563_cable_length_table[] = {
+	0, 60, 115, 150, 150, 60, 115, 150, 180, 180, 0xFF
+};
+
+#define GG82563_CABLE_LENGTH_TABLE_SIZE \
+		ARRAY_SIZE(e1000_gg82563_cable_length_table)
+
+static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw);
+static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
+static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask);
+static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw);
+static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw);
+static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw);
+static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex);
+static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+					   u16 *data);
+static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+					    u16 data);
+static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw);
+
+/**
+ *  e1000_init_phy_params_80003es2lan - Init ESB2 PHY func ptrs.
+ *  @hw: pointer to the HW structure
+ **/
+static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+
+	if (hw->phy.media_type != e1000_media_type_copper) {
+		phy->type = e1000_phy_none;
+		return 0;
+	} else {
+		phy->ops.power_up = e1000_power_up_phy_copper;
+		phy->ops.power_down = e1000_power_down_phy_copper_80003es2lan;
+	}
+
+	phy->addr = 1;
+	phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
+	phy->reset_delay_us = 100;
+	phy->type = e1000_phy_gg82563;
+
+	/* This can only be done after all function pointers are setup. */
+	ret_val = e1000e_get_phy_id(hw);
+
+	/* Verify phy id */
+	if (phy->id != GG82563_E_PHY_ID)
+		return -E1000_ERR_PHY;
+
+	return ret_val;
+}
+
+/**
+ *  e1000_init_nvm_params_80003es2lan - Init ESB2 NVM func ptrs.
+ *  @hw: pointer to the HW structure
+ **/
+static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw)
+{
+	struct e1000_nvm_info *nvm = &hw->nvm;
+	u32 eecd = er32(EECD);
+	u16 size;
+
+	nvm->opcode_bits = 8;
+	nvm->delay_usec = 1;
+	switch (nvm->override) {
+	case e1000_nvm_override_spi_large:
+		nvm->page_size = 32;
+		nvm->address_bits = 16;
+		break;
+	case e1000_nvm_override_spi_small:
+		nvm->page_size = 8;
+		nvm->address_bits = 8;
+		break;
+	default:
+		nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
+		nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
+		break;
+	}
+
+	nvm->type = e1000_nvm_eeprom_spi;
+
+	size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
+		     E1000_EECD_SIZE_EX_SHIFT);
+
+	/* Added to a constant, "size" becomes the left-shift value
+	 * for setting word_size.
+	 */
+	size += NVM_WORD_SIZE_BASE_SHIFT;
+
+	/* EEPROM access above 16k is unsupported */
+	if (size > 14)
+		size = 14;
+	nvm->word_size = BIT(size);
+
+	return 0;
+}
+
+/**
+ *  e1000_init_mac_params_80003es2lan - Init ESB2 MAC func ptrs.
+ *  @hw: pointer to the HW structure
+ **/
+static s32 e1000_init_mac_params_80003es2lan(struct e1000_hw *hw)
+{
+	struct e1000_mac_info *mac = &hw->mac;
+
+	/* Set media type and media-dependent function pointers */
+	switch (hw->adapter->pdev->device) {
+	case E1000_DEV_ID_80003ES2LAN_SERDES_DPT:
+		hw->phy.media_type = e1000_media_type_internal_serdes;
+		mac->ops.check_for_link = e1000e_check_for_serdes_link;
+		mac->ops.setup_physical_interface =
+		    e1000e_setup_fiber_serdes_link;
+		break;
+	default:
+		hw->phy.media_type = e1000_media_type_copper;
+		mac->ops.check_for_link = e1000e_check_for_copper_link;
+		mac->ops.setup_physical_interface =
+		    e1000_setup_copper_link_80003es2lan;
+		break;
+	}
+
+	/* Set mta register count */
+	mac->mta_reg_count = 128;
+	/* Set rar entry count */
+	mac->rar_entry_count = E1000_RAR_ENTRIES;
+	/* FWSM register */
+	mac->has_fwsm = true;
+	/* ARC supported; valid only if manageability features are enabled. */
+	mac->arc_subsystem_valid = !!(er32(FWSM) & E1000_FWSM_MODE_MASK);
+	/* Adaptive IFS not supported */
+	mac->adaptive_ifs = false;
+
+	/* set lan id for port to determine which phy lock to use */
+	hw->mac.ops.set_lan_id(hw);
+
+	return 0;
+}
+
+static s32 e1000_get_variants_80003es2lan(struct e1000_adapter *adapter)
+{
+	struct e1000_hw *hw = &adapter->hw;
+	s32 rc;
+
+	rc = e1000_init_mac_params_80003es2lan(hw);
+	if (rc)
+		return rc;
+
+	rc = e1000_init_nvm_params_80003es2lan(hw);
+	if (rc)
+		return rc;
+
+	rc = e1000_init_phy_params_80003es2lan(hw);
+	if (rc)
+		return rc;
+
+	return 0;
+}
+
+/**
+ *  e1000_acquire_phy_80003es2lan - Acquire rights to access PHY
+ *  @hw: pointer to the HW structure
+ *
+ *  A wrapper to acquire access rights to the correct PHY.
+ **/
+static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw)
+{
+	u16 mask;
+
+	mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+	return e1000_acquire_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ *  e1000_release_phy_80003es2lan - Release rights to access PHY
+ *  @hw: pointer to the HW structure
+ *
+ *  A wrapper to release access rights to the correct PHY.
+ **/
+static void e1000_release_phy_80003es2lan(struct e1000_hw *hw)
+{
+	u16 mask;
+
+	mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM;
+	e1000_release_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ *  e1000_acquire_mac_csr_80003es2lan - Acquire right to access Kumeran register
+ *  @hw: pointer to the HW structure
+ *
+ *  Acquire the semaphore to access the Kumeran interface.
+ *
+ **/
+static s32 e1000_acquire_mac_csr_80003es2lan(struct e1000_hw *hw)
+{
+	u16 mask;
+
+	mask = E1000_SWFW_CSR_SM;
+
+	return e1000_acquire_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ *  e1000_release_mac_csr_80003es2lan - Release right to access Kumeran Register
+ *  @hw: pointer to the HW structure
+ *
+ *  Release the semaphore used to access the Kumeran interface
+ **/
+static void e1000_release_mac_csr_80003es2lan(struct e1000_hw *hw)
+{
+	u16 mask;
+
+	mask = E1000_SWFW_CSR_SM;
+
+	e1000_release_swfw_sync_80003es2lan(hw, mask);
+}
+
+/**
+ *  e1000_acquire_nvm_80003es2lan - Acquire rights to access NVM
+ *  @hw: pointer to the HW structure
+ *
+ *  Acquire the semaphore to access the EEPROM.
+ **/
+static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw)
+{
+	s32 ret_val;
+
+	ret_val = e1000_acquire_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+	if (ret_val)
+		return ret_val;
+
+	ret_val = e1000e_acquire_nvm(hw);
+
+	if (ret_val)
+		e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_release_nvm_80003es2lan - Relinquish rights to access NVM
+ *  @hw: pointer to the HW structure
+ *
+ *  Release the semaphore used to access the EEPROM.
+ **/
+static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw)
+{
+	e1000e_release_nvm(hw);
+	e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM);
+}
+
+/**
+ *  e1000_acquire_swfw_sync_80003es2lan - Acquire SW/FW semaphore
+ *  @hw: pointer to the HW structure
+ *  @mask: specifies which semaphore to acquire
+ *
+ *  Acquire the SW/FW semaphore to access the PHY or NVM.  The mask
+ *  will also specify which port we're acquiring the lock for.
+ **/
+static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
+{
+	u32 swfw_sync;
+	u32 swmask = mask;
+	u32 fwmask = mask << 16;
+	s32 i = 0;
+	s32 timeout = 50;
+
+	while (i < timeout) {
+		if (e1000e_get_hw_semaphore(hw))
+			return -E1000_ERR_SWFW_SYNC;
+
+		swfw_sync = er32(SW_FW_SYNC);
+		if (!(swfw_sync & (fwmask | swmask)))
+			break;
+
+		/* Firmware currently using resource (fwmask)
+		 * or other software thread using resource (swmask)
+		 */
+		e1000e_put_hw_semaphore(hw);
+		mdelay(5);
+		i++;
+	}
+
+	if (i == timeout) {
+		e_dbg("Driver can't access resource, SW_FW_SYNC timeout.\n");
+		return -E1000_ERR_SWFW_SYNC;
+	}
+
+	swfw_sync |= swmask;
+	ew32(SW_FW_SYNC, swfw_sync);
+
+	e1000e_put_hw_semaphore(hw);
+
+	return 0;
+}
+
+/**
+ *  e1000_release_swfw_sync_80003es2lan - Release SW/FW semaphore
+ *  @hw: pointer to the HW structure
+ *  @mask: specifies which semaphore to acquire
+ *
+ *  Release the SW/FW semaphore used to access the PHY or NVM.  The mask
+ *  will also specify which port we're releasing the lock for.
+ **/
+static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask)
+{
+	u32 swfw_sync;
+
+	while (e1000e_get_hw_semaphore(hw) != 0)
+		; /* Empty */
+
+	swfw_sync = er32(SW_FW_SYNC);
+	swfw_sync &= ~mask;
+	ew32(SW_FW_SYNC, swfw_sync);
+
+	e1000e_put_hw_semaphore(hw);
+}
+
+/**
+ *  e1000_read_phy_reg_gg82563_80003es2lan - Read GG82563 PHY register
+ *  @hw: pointer to the HW structure
+ *  @offset: offset of the register to read
+ *  @data: pointer to the data returned from the operation
+ *
+ *  Read the GG82563 PHY register.
+ **/
+static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
+						  u32 offset, u16 *data)
+{
+	s32 ret_val;
+	u32 page_select;
+	u16 temp;
+
+	ret_val = e1000_acquire_phy_80003es2lan(hw);
+	if (ret_val)
+		return ret_val;
+
+	/* Select Configuration Page */
+	if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
+		page_select = GG82563_PHY_PAGE_SELECT;
+	} else {
+		/* Use Alternative Page Select register to access
+		 * registers 30 and 31
+		 */
+		page_select = GG82563_PHY_PAGE_SELECT_ALT;
+	}
+
+	temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
+	ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
+	if (ret_val) {
+		e1000_release_phy_80003es2lan(hw);
+		return ret_val;
+	}
+
+	if (hw->dev_spec.e80003es2lan.mdic_wa_enable) {
+		/* The "ready" bit in the MDIC register may be incorrectly set
+		 * before the device has completed the "Page Select" MDI
+		 * transaction.  So we wait 200us after each MDI command...
+		 */
+		usleep_range(200, 400);
+
+		/* ...and verify the command was successful. */
+		ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
+
+		if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+			e1000_release_phy_80003es2lan(hw);
+			return -E1000_ERR_PHY;
+		}
+
+		usleep_range(200, 400);
+
+		ret_val = e1000e_read_phy_reg_mdic(hw,
+						   MAX_PHY_REG_ADDRESS & offset,
+						   data);
+
+		usleep_range(200, 400);
+	} else {
+		ret_val = e1000e_read_phy_reg_mdic(hw,
+						   MAX_PHY_REG_ADDRESS & offset,
+						   data);
+	}
+
+	e1000_release_phy_80003es2lan(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_write_phy_reg_gg82563_80003es2lan - Write GG82563 PHY register
+ *  @hw: pointer to the HW structure
+ *  @offset: offset of the register to read
+ *  @data: value to write to the register
+ *
+ *  Write to the GG82563 PHY register.
+ **/
+static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw,
+						   u32 offset, u16 data)
+{
+	s32 ret_val;
+	u32 page_select;
+	u16 temp;
+
+	ret_val = e1000_acquire_phy_80003es2lan(hw);
+	if (ret_val)
+		return ret_val;
+
+	/* Select Configuration Page */
+	if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) {
+		page_select = GG82563_PHY_PAGE_SELECT;
+	} else {
+		/* Use Alternative Page Select register to access
+		 * registers 30 and 31
+		 */
+		page_select = GG82563_PHY_PAGE_SELECT_ALT;
+	}
+
+	temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT);
+	ret_val = e1000e_write_phy_reg_mdic(hw, page_select, temp);
+	if (ret_val) {
+		e1000_release_phy_80003es2lan(hw);
+		return ret_val;
+	}
+
+	if (hw->dev_spec.e80003es2lan.mdic_wa_enable) {
+		/* The "ready" bit in the MDIC register may be incorrectly set
+		 * before the device has completed the "Page Select" MDI
+		 * transaction.  So we wait 200us after each MDI command...
+		 */
+		usleep_range(200, 400);
+
+		/* ...and verify the command was successful. */
+		ret_val = e1000e_read_phy_reg_mdic(hw, page_select, &temp);
+
+		if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) {
+			e1000_release_phy_80003es2lan(hw);
+			return -E1000_ERR_PHY;
+		}
+
+		usleep_range(200, 400);
+
+		ret_val = e1000e_write_phy_reg_mdic(hw,
+						    MAX_PHY_REG_ADDRESS &
+						    offset, data);
+
+		usleep_range(200, 400);
+	} else {
+		ret_val = e1000e_write_phy_reg_mdic(hw,
+						    MAX_PHY_REG_ADDRESS &
+						    offset, data);
+	}
+
+	e1000_release_phy_80003es2lan(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_write_nvm_80003es2lan - Write to ESB2 NVM
+ *  @hw: pointer to the HW structure
+ *  @offset: offset of the register to read
+ *  @words: number of words to write
+ *  @data: buffer of data to write to the NVM
+ *
+ *  Write "words" of data to the ESB2 NVM.
+ **/
+static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset,
+				       u16 words, u16 *data)
+{
+	return e1000e_write_nvm_spi(hw, offset, words, data);
+}
+
+/**
+ *  e1000_get_cfg_done_80003es2lan - Wait for configuration to complete
+ *  @hw: pointer to the HW structure
+ *
+ *  Wait a specific amount of time for manageability processes to complete.
+ *  This is a function pointer entry point called by the phy module.
+ **/
+static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw)
+{
+	s32 timeout = PHY_CFG_TIMEOUT;
+	u32 mask = E1000_NVM_CFG_DONE_PORT_0;
+
+	if (hw->bus.func == 1)
+		mask = E1000_NVM_CFG_DONE_PORT_1;
+
+	while (timeout) {
+		if (er32(EEMNGCTL) & mask)
+			break;
+		usleep_range(1000, 2000);
+		timeout--;
+	}
+	if (!timeout) {
+		e_dbg("MNG configuration cycle has not completed.\n");
+		return -E1000_ERR_RESET;
+	}
+
+	return 0;
+}
+
+/**
+ *  e1000_phy_force_speed_duplex_80003es2lan - Force PHY speed and duplex
+ *  @hw: pointer to the HW structure
+ *
+ *  Force the speed and duplex settings onto the PHY.  This is a
+ *  function pointer entry point called by the phy module.
+ **/
+static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw)
+{
+	s32 ret_val;
+	u16 phy_data;
+	bool link;
+
+	/* Clear Auto-Crossover to force MDI manually.  M88E1000 requires MDI
+	 * forced whenever speed and duplex are forced.
+	 */
+	ret_val = e1e_rphy(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
+	if (ret_val)
+		return ret_val;
+
+	phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_AUTO;
+	ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, phy_data);
+	if (ret_val)
+		return ret_val;
+
+	e_dbg("GG82563 PSCR: %X\n", phy_data);
+
+	ret_val = e1e_rphy(hw, MII_BMCR, &phy_data);
+	if (ret_val)
+		return ret_val;
+
+	e1000e_phy_force_speed_duplex_setup(hw, &phy_data);
+
+	/* Reset the phy to commit changes. */
+	phy_data |= BMCR_RESET;
+
+	ret_val = e1e_wphy(hw, MII_BMCR, phy_data);
+	if (ret_val)
+		return ret_val;
+
+	udelay(1);
+
+	if (hw->phy.autoneg_wait_to_complete) {
+		e_dbg("Waiting for forced speed/duplex link on GG82563 phy.\n");
+
+		ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+						      100000, &link);
+		if (ret_val)
+			return ret_val;
+
+		if (!link) {
+			/* We didn't get link.
+			 * Reset the DSP and cross our fingers.
+			 */
+			ret_val = e1000e_phy_reset_dsp(hw);
+			if (ret_val)
+				return ret_val;
+		}
+
+		/* Try once more */
+		ret_val = e1000e_phy_has_link_generic(hw, PHY_FORCE_LIMIT,
+						      100000, &link);
+		if (ret_val)
+			return ret_val;
+	}
+
+	ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data);
+	if (ret_val)
+		return ret_val;
+
+	/* Resetting the phy means we need to verify the TX_CLK corresponds
+	 * to the link speed.  10Mbps -> 2.5MHz, else 25MHz.
+	 */
+	phy_data &= ~GG82563_MSCR_TX_CLK_MASK;
+	if (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED)
+		phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5;
+	else
+		phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25;
+
+	/* In addition, we must re-enable CRS on Tx for both half and full
+	 * duplex.
+	 */
+	phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+	ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_get_cable_length_80003es2lan - Set approximate cable length
+ *  @hw: pointer to the HW structure
+ *
+ *  Find the approximate cable length as measured by the GG82563 PHY.
+ *  This is a function pointer entry point called by the phy module.
+ **/
+static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u16 phy_data, index;
+
+	ret_val = e1e_rphy(hw, GG82563_PHY_DSP_DISTANCE, &phy_data);
+	if (ret_val)
+		return ret_val;
+
+	index = phy_data & GG82563_DSPD_CABLE_LENGTH;
+
+	if (index >= GG82563_CABLE_LENGTH_TABLE_SIZE - 5)
+		return -E1000_ERR_PHY;
+
+	phy->min_cable_length = e1000_gg82563_cable_length_table[index];
+	phy->max_cable_length = e1000_gg82563_cable_length_table[index + 5];
+
+	phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2;
+
+	return 0;
+}
+
+/**
+ *  e1000_get_link_up_info_80003es2lan - Report speed and duplex
+ *  @hw: pointer to the HW structure
+ *  @speed: pointer to speed buffer
+ *  @duplex: pointer to duplex buffer
+ *
+ *  Retrieve the current speed and duplex configuration.
+ **/
+static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed,
+					      u16 *duplex)
+{
+	s32 ret_val;
+
+	if (hw->phy.media_type == e1000_media_type_copper) {
+		ret_val = e1000e_get_speed_and_duplex_copper(hw, speed, duplex);
+		hw->phy.ops.cfg_on_link_up(hw);
+	} else {
+		ret_val = e1000e_get_speed_and_duplex_fiber_serdes(hw,
+								   speed,
+								   duplex);
+	}
+
+	return ret_val;
+}
+
+/**
+ *  e1000_reset_hw_80003es2lan - Reset the ESB2 controller
+ *  @hw: pointer to the HW structure
+ *
+ *  Perform a global reset to the ESB2 controller.
+ **/
+static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
+{
+	u32 ctrl;
+	s32 ret_val;
+	u16 kum_reg_data;
+
+	/* Prevent the PCI-E bus from sticking if there is no TLP connection
+	 * on the last TLP read/write transaction when MAC is reset.
+	 */
+	ret_val = e1000e_disable_pcie_master(hw);
+	if (ret_val)
+		e_dbg("PCI-E Master disable polling has failed.\n");
+
+	e_dbg("Masking off all interrupts\n");
+	ew32(IMC, 0xffffffff);
+
+	ew32(RCTL, 0);
+	ew32(TCTL, E1000_TCTL_PSP);
+	e1e_flush();
+
+	usleep_range(10000, 20000);
+
+	ctrl = er32(CTRL);
+
+	ret_val = e1000_acquire_phy_80003es2lan(hw);
+	if (ret_val)
+		return ret_val;
+
+	e_dbg("Issuing a global reset to MAC\n");
+	ew32(CTRL, ctrl | E1000_CTRL_RST);
+	e1000_release_phy_80003es2lan(hw);
+
+	/* Disable IBIST slave mode (far-end loopback) */
+	ret_val =
+	    e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+					    &kum_reg_data);
+	if (ret_val)
+		return ret_val;
+	kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE;
+	e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+					 kum_reg_data);
+
+	ret_val = e1000e_get_auto_rd_done(hw);
+	if (ret_val)
+		/* We don't want to continue accessing MAC registers. */
+		return ret_val;
+
+	/* Clear any pending interrupt events. */
+	ew32(IMC, 0xffffffff);
+	er32(ICR);
+
+	return e1000_check_alt_mac_addr_generic(hw);
+}
+
+/**
+ *  e1000_init_hw_80003es2lan - Initialize the ESB2 controller
+ *  @hw: pointer to the HW structure
+ *
+ *  Initialize the hw bits, LED, VFTA, MTA, link and hw counters.
+ **/
+static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw)
+{
+	struct e1000_mac_info *mac = &hw->mac;
+	u32 reg_data;
+	s32 ret_val;
+	u16 kum_reg_data;
+	u16 i;
+
+	e1000_initialize_hw_bits_80003es2lan(hw);
+
+	/* Initialize identification LED */
+	ret_val = mac->ops.id_led_init(hw);
+	/* An error is not fatal and we should not stop init due to this */
+	if (ret_val)
+		e_dbg("Error initializing identification LED\n");
+
+	/* Disabling VLAN filtering */
+	e_dbg("Initializing the IEEE VLAN\n");
+	mac->ops.clear_vfta(hw);
+
+	/* Setup the receive address. */
+	e1000e_init_rx_addrs(hw, mac->rar_entry_count);
+
+	/* Zero out the Multicast HASH table */
+	e_dbg("Zeroing the MTA\n");
+	for (i = 0; i < mac->mta_reg_count; i++)
+		E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
+
+	/* Setup link and flow control */
+	ret_val = mac->ops.setup_link(hw);
+	if (ret_val)
+		return ret_val;
+
+	/* Disable IBIST slave mode (far-end loopback) */
+	e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+					&kum_reg_data);
+	kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE;
+	e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+					 kum_reg_data);
+
+	/* Set the transmit descriptor write-back policy */
+	reg_data = er32(TXDCTL(0));
+	reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) |
+		    E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC);
+	ew32(TXDCTL(0), reg_data);
+
+	/* ...for both queues. */
+	reg_data = er32(TXDCTL(1));
+	reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) |
+		    E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC);
+	ew32(TXDCTL(1), reg_data);
+
+	/* Enable retransmit on late collisions */
+	reg_data = er32(TCTL);
+	reg_data |= E1000_TCTL_RTLC;
+	ew32(TCTL, reg_data);
+
+	/* Configure Gigabit Carry Extend Padding */
+	reg_data = er32(TCTL_EXT);
+	reg_data &= ~E1000_TCTL_EXT_GCEX_MASK;
+	reg_data |= DEFAULT_TCTL_EXT_GCEX_80003ES2LAN;
+	ew32(TCTL_EXT, reg_data);
+
+	/* Configure Transmit Inter-Packet Gap */
+	reg_data = er32(TIPG);
+	reg_data &= ~E1000_TIPG_IPGT_MASK;
+	reg_data |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
+	ew32(TIPG, reg_data);
+
+	reg_data = E1000_READ_REG_ARRAY(hw, E1000_FFLT, 0x0001);
+	reg_data &= ~0x00100000;
+	E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data);
+
+	/* default to true to enable the MDIC W/A */
+	hw->dev_spec.e80003es2lan.mdic_wa_enable = true;
+
+	ret_val =
+	    e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_OFFSET >>
+					    E1000_KMRNCTRLSTA_OFFSET_SHIFT, &i);
+	if (!ret_val) {
+		if ((i & E1000_KMRNCTRLSTA_OPMODE_MASK) ==
+		    E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO)
+			hw->dev_spec.e80003es2lan.mdic_wa_enable = false;
+	}
+
+	/* Clear all of the statistics registers (clear on read).  It is
+	 * important that we do this after we have tried to establish link
+	 * because the symbol error count will increment wildly if there
+	 * is no link.
+	 */
+	e1000_clear_hw_cntrs_80003es2lan(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_initialize_hw_bits_80003es2lan - Init hw bits of ESB2
+ *  @hw: pointer to the HW structure
+ *
+ *  Initializes required hardware-dependent bits needed for normal operation.
+ **/
+static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw)
+{
+	u32 reg;
+
+	/* Transmit Descriptor Control 0 */
+	reg = er32(TXDCTL(0));
+	reg |= BIT(22);
+	ew32(TXDCTL(0), reg);
+
+	/* Transmit Descriptor Control 1 */
+	reg = er32(TXDCTL(1));
+	reg |= BIT(22);
+	ew32(TXDCTL(1), reg);
+
+	/* Transmit Arbitration Control 0 */
+	reg = er32(TARC(0));
+	reg &= ~(0xF << 27);	/* 30:27 */
+	if (hw->phy.media_type != e1000_media_type_copper)
+		reg &= ~BIT(20);
+	ew32(TARC(0), reg);
+
+	/* Transmit Arbitration Control 1 */
+	reg = er32(TARC(1));
+	if (er32(TCTL) & E1000_TCTL_MULR)
+		reg &= ~BIT(28);
+	else
+		reg |= BIT(28);
+	ew32(TARC(1), reg);
+
+	/* Disable IPv6 extension header parsing because some malformed
+	 * IPv6 headers can hang the Rx.
+	 */
+	reg = er32(RFCTL);
+	reg |= (E1000_RFCTL_IPV6_EX_DIS | E1000_RFCTL_NEW_IPV6_EXT_DIS);
+	ew32(RFCTL, reg);
+}
+
+/**
+ *  e1000_copper_link_setup_gg82563_80003es2lan - Configure GG82563 Link
+ *  @hw: pointer to the HW structure
+ *
+ *  Setup some GG82563 PHY registers for obtaining link
+ **/
+static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw)
+{
+	struct e1000_phy_info *phy = &hw->phy;
+	s32 ret_val;
+	u32 reg;
+	u16 data;
+
+	ret_val = e1e_rphy(hw, GG82563_PHY_MAC_SPEC_CTRL, &data);
+	if (ret_val)
+		return ret_val;
+
+	data |= GG82563_MSCR_ASSERT_CRS_ON_TX;
+	/* Use 25MHz for both link down and 1000Base-T for Tx clock. */
+	data |= GG82563_MSCR_TX_CLK_1000MBPS_25;
+
+	ret_val = e1e_wphy(hw, GG82563_PHY_MAC_SPEC_CTRL, data);
+	if (ret_val)
+		return ret_val;
+
+	/* Options:
+	 *   MDI/MDI-X = 0 (default)
+	 *   0 - Auto for all speeds
+	 *   1 - MDI mode
+	 *   2 - MDI-X mode
+	 *   3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes)
+	 */
+	ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL, &data);
+	if (ret_val)
+		return ret_val;
+
+	data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK;
+
+	switch (phy->mdix) {
+	case 1:
+		data |= GG82563_PSCR_CROSSOVER_MODE_MDI;
+		break;
+	case 2:
+		data |= GG82563_PSCR_CROSSOVER_MODE_MDIX;
+		break;
+	case 0:
+	default:
+		data |= GG82563_PSCR_CROSSOVER_MODE_AUTO;
+		break;
+	}
+
+	/* Options:
+	 *   disable_polarity_correction = 0 (default)
+	 *       Automatic Correction for Reversed Cable Polarity
+	 *   0 - Disabled
+	 *   1 - Enabled
+	 */
+	data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+	if (phy->disable_polarity_correction)
+		data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE;
+
+	ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL, data);
+	if (ret_val)
+		return ret_val;
+
+	/* SW Reset the PHY so all changes take effect */
+	ret_val = hw->phy.ops.commit(hw);
+	if (ret_val) {
+		e_dbg("Error Resetting the PHY\n");
+		return ret_val;
+	}
+
+	/* Bypass Rx and Tx FIFO's */
+	reg = E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL;
+	data = (E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS |
+		E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS);
+	ret_val = e1000_write_kmrn_reg_80003es2lan(hw, reg, data);
+	if (ret_val)
+		return ret_val;
+
+	reg = E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE;
+	ret_val = e1000_read_kmrn_reg_80003es2lan(hw, reg, &data);
+	if (ret_val)
+		return ret_val;
+	data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE;
+	ret_val = e1000_write_kmrn_reg_80003es2lan(hw, reg, data);
+	if (ret_val)
+		return ret_val;
+
+	ret_val = e1e_rphy(hw, GG82563_PHY_SPEC_CTRL_2, &data);
+	if (ret_val)
+		return ret_val;
+
+	data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG;
+	ret_val = e1e_wphy(hw, GG82563_PHY_SPEC_CTRL_2, data);
+	if (ret_val)
+		return ret_val;
+
+	reg = er32(CTRL_EXT);
+	reg &= ~E1000_CTRL_EXT_LINK_MODE_MASK;
+	ew32(CTRL_EXT, reg);
+
+	ret_val = e1e_rphy(hw, GG82563_PHY_PWR_MGMT_CTRL, &data);
+	if (ret_val)
+		return ret_val;
+
+	/* Do not init these registers when the HW is in IAMT mode, since the
+	 * firmware will have already initialized them.  We only initialize
+	 * them if the HW is not in IAMT mode.
+	 */
+	if (!hw->mac.ops.check_mng_mode(hw)) {
+		/* Enable Electrical Idle on the PHY */
+		data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE;
+		ret_val = e1e_wphy(hw, GG82563_PHY_PWR_MGMT_CTRL, data);
+		if (ret_val)
+			return ret_val;
+
+		ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &data);
+		if (ret_val)
+			return ret_val;
+
+		data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+		ret_val = e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, data);
+		if (ret_val)
+			return ret_val;
+	}
+
+	/* Workaround: Disable padding in Kumeran interface in the MAC
+	 * and in the PHY to avoid CRC errors.
+	 */
+	ret_val = e1e_rphy(hw, GG82563_PHY_INBAND_CTRL, &data);
+	if (ret_val)
+		return ret_val;
+
+	data |= GG82563_ICR_DIS_PADDING;
+	ret_val = e1e_wphy(hw, GG82563_PHY_INBAND_CTRL, data);
+	if (ret_val)
+		return ret_val;
+
+	return 0;
+}
+
+/**
+ *  e1000_setup_copper_link_80003es2lan - Setup Copper Link for ESB2
+ *  @hw: pointer to the HW structure
+ *
+ *  Essentially a wrapper for setting up all things "copper" related.
+ *  This is a function pointer entry point called by the mac module.
+ **/
+static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw)
+{
+	u32 ctrl;
+	s32 ret_val;
+	u16 reg_data;
+
+	ctrl = er32(CTRL);
+	ctrl |= E1000_CTRL_SLU;
+	ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
+	ew32(CTRL, ctrl);
+
+	/* Set the mac to wait the maximum time between each
+	 * iteration and increase the max iterations when
+	 * polling the phy; this fixes erroneous timeouts at 10Mbps.
+	 */
+	ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 4),
+						   0xFFFF);
+	if (ret_val)
+		return ret_val;
+	ret_val = e1000_read_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9),
+						  &reg_data);
+	if (ret_val)
+		return ret_val;
+	reg_data |= 0x3F;
+	ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9),
+						   reg_data);
+	if (ret_val)
+		return ret_val;
+	ret_val =
+	    e1000_read_kmrn_reg_80003es2lan(hw,
+					    E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
+					    &reg_data);
+	if (ret_val)
+		return ret_val;
+	reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING;
+	ret_val =
+	    e1000_write_kmrn_reg_80003es2lan(hw,
+					     E1000_KMRNCTRLSTA_OFFSET_INB_CTRL,
+					     reg_data);
+	if (ret_val)
+		return ret_val;
+
+	ret_val = e1000_copper_link_setup_gg82563_80003es2lan(hw);
+	if (ret_val)
+		return ret_val;
+
+	return e1000e_setup_copper_link(hw);
+}
+
+/**
+ *  e1000_cfg_on_link_up_80003es2lan - es2 link configuration after link-up
+ *  @hw: pointer to the HW structure
+ *  @duplex: current duplex setting
+ *
+ *  Configure the KMRN interface by applying last minute quirks for
+ *  10/100 operation.
+ **/
+static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw)
+{
+	s32 ret_val = 0;
+	u16 speed;
+	u16 duplex;
+
+	if (hw->phy.media_type == e1000_media_type_copper) {
+		ret_val = e1000e_get_speed_and_duplex_copper(hw, &speed,
+							     &duplex);
+		if (ret_val)
+			return ret_val;
+
+		if (speed == SPEED_1000)
+			ret_val = e1000_cfg_kmrn_1000_80003es2lan(hw);
+		else
+			ret_val = e1000_cfg_kmrn_10_100_80003es2lan(hw, duplex);
+	}
+
+	return ret_val;
+}
+
+/**
+ *  e1000_cfg_kmrn_10_100_80003es2lan - Apply "quirks" for 10/100 operation
+ *  @hw: pointer to the HW structure
+ *  @duplex: current duplex setting
+ *
+ *  Configure the KMRN interface by applying last minute quirks for
+ *  10/100 operation.
+ **/
+static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex)
+{
+	s32 ret_val;
+	u32 tipg;
+	u32 i = 0;
+	u16 reg_data, reg_data2;
+
+	reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT;
+	ret_val =
+	    e1000_write_kmrn_reg_80003es2lan(hw,
+					     E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+					     reg_data);
+	if (ret_val)
+		return ret_val;
+
+	/* Configure Transmit Inter-Packet Gap */
+	tipg = er32(TIPG);
+	tipg &= ~E1000_TIPG_IPGT_MASK;
+	tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN;
+	ew32(TIPG, tipg);
+
+	do {
+		ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
+		if (ret_val)
+			return ret_val;
+
+		ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data2);
+		if (ret_val)
+			return ret_val;
+		i++;
+	} while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
+
+	if (duplex == HALF_DUPLEX)
+		reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER;
+	else
+		reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+
+	return e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+}
+
+/**
+ *  e1000_cfg_kmrn_1000_80003es2lan - Apply "quirks" for gigabit operation
+ *  @hw: pointer to the HW structure
+ *
+ *  Configure the KMRN interface by applying last minute quirks for
+ *  gigabit operation.
+ **/
+static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw)
+{
+	s32 ret_val;
+	u16 reg_data, reg_data2;
+	u32 tipg;
+	u32 i = 0;
+
+	reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT;
+	ret_val =
+	    e1000_write_kmrn_reg_80003es2lan(hw,
+					     E1000_KMRNCTRLSTA_OFFSET_HD_CTRL,
+					     reg_data);
+	if (ret_val)
+		return ret_val;
+
+	/* Configure Transmit Inter-Packet Gap */
+	tipg = er32(TIPG);
+	tipg &= ~E1000_TIPG_IPGT_MASK;
+	tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN;
+	ew32(TIPG, tipg);
+
+	do {
+		ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data);
+		if (ret_val)
+			return ret_val;
+
+		ret_val = e1e_rphy(hw, GG82563_PHY_KMRN_MODE_CTRL, &reg_data2);
+		if (ret_val)
+			return ret_val;
+		i++;
+	} while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY));
+
+	reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER;
+
+	return e1e_wphy(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data);
+}
+
+/**
+ *  e1000_read_kmrn_reg_80003es2lan - Read kumeran register
+ *  @hw: pointer to the HW structure
+ *  @offset: register offset to be read
+ *  @data: pointer to the read data
+ *
+ *  Acquire semaphore, then read the PHY register at offset
+ *  using the kumeran interface.  The information retrieved is stored in data.
+ *  Release the semaphore before exiting.
+ **/
+static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+					   u16 *data)
+{
+	u32 kmrnctrlsta;
+	s32 ret_val;
+
+	ret_val = e1000_acquire_mac_csr_80003es2lan(hw);
+	if (ret_val)
+		return ret_val;
+
+	kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
+		       E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN;
+	ew32(KMRNCTRLSTA, kmrnctrlsta);
+	e1e_flush();
+
+	udelay(2);
+
+	kmrnctrlsta = er32(KMRNCTRLSTA);
+	*data = (u16)kmrnctrlsta;
+
+	e1000_release_mac_csr_80003es2lan(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_write_kmrn_reg_80003es2lan - Write kumeran register
+ *  @hw: pointer to the HW structure
+ *  @offset: register offset to write to
+ *  @data: data to write at register offset
+ *
+ *  Acquire semaphore, then write the data to PHY register
+ *  at the offset using the kumeran interface.  Release semaphore
+ *  before exiting.
+ **/
+static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset,
+					    u16 data)
+{
+	u32 kmrnctrlsta;
+	s32 ret_val;
+
+	ret_val = e1000_acquire_mac_csr_80003es2lan(hw);
+	if (ret_val)
+		return ret_val;
+
+	kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) &
+		       E1000_KMRNCTRLSTA_OFFSET) | data;
+	ew32(KMRNCTRLSTA, kmrnctrlsta);
+	e1e_flush();
+
+	udelay(2);
+
+	e1000_release_mac_csr_80003es2lan(hw);
+
+	return ret_val;
+}
+
+/**
+ *  e1000_read_mac_addr_80003es2lan - Read device MAC address
+ *  @hw: pointer to the HW structure
+ **/
+static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw)
+{
+	s32 ret_val;
+
+	/* If there's an alternate MAC address place it in RAR0
+	 * so that it will override the Si installed default perm
+	 * address.
+	 */
+	ret_val = e1000_check_alt_mac_addr_generic(hw);
+	if (ret_val)
+		return ret_val;
+
+	return e1000_read_mac_addr_generic(hw);
+}
+
+/**
+ * e1000_power_down_phy_copper_80003es2lan - Remove link during PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, remove the link.
+ **/
+static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw)
+{
+	/* If the management interface is not enabled, then power down */
+	if (!(hw->mac.ops.check_mng_mode(hw) ||
+	      hw->phy.ops.check_reset_block(hw)))
+		e1000_power_down_phy_copper(hw);
+}
+
+/**
+ *  e1000_clear_hw_cntrs_80003es2lan - Clear device specific hardware counters
+ *  @hw: pointer to the HW structure
+ *
+ *  Clears the hardware counters by reading the counter registers.
+ **/
+static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw)
+{
+	e1000e_clear_hw_cntrs_base(hw);
+
+	er32(PRC64);
+	er32(PRC127);
+	er32(PRC255);
+	er32(PRC511);
+	er32(PRC1023);
+	er32(PRC1522);
+	er32(PTC64);
+	er32(PTC127);
+	er32(PTC255);
+	er32(PTC511);
+	er32(PTC1023);
+	er32(PTC1522);
+
+	er32(ALGNERRC);
+	er32(RXERRC);
+	er32(TNCRS);
+	er32(CEXTERR);
+	er32(TSCTC);
+	er32(TSCTFC);
+
+	er32(MGTPRC);
+	er32(MGTPDC);
+	er32(MGTPTC);
+
+	er32(IAC);
+	er32(ICRXOC);
+
+	er32(ICRXPTC);
+	er32(ICRXATC);
+	er32(ICTXPTC);
+	er32(ICTXATC);
+	er32(ICTXQEC);
+	er32(ICTXQMTC);
+	er32(ICRXDMTC);
+}
+
+static const struct e1000_mac_operations es2_mac_ops = {
+	.read_mac_addr		= e1000_read_mac_addr_80003es2lan,
+	.id_led_init		= e1000e_id_led_init_generic,
+	.blink_led		= e1000e_blink_led_generic,
+	.check_mng_mode		= e1000e_check_mng_mode_generic,
+	/* check_for_link dependent on media type */
+	.cleanup_led		= e1000e_cleanup_led_generic,
+	.clear_hw_cntrs		= e1000_clear_hw_cntrs_80003es2lan,
+	.get_bus_info		= e1000e_get_bus_info_pcie,
+	.set_lan_id		= e1000_set_lan_id_multi_port_pcie,
+	.get_link_up_info	= e1000_get_link_up_info_80003es2lan,
+	.led_on			= e1000e_led_on_generic,
+	.led_off		= e1000e_led_off_generic,
+	.update_mc_addr_list	= e1000e_update_mc_addr_list_generic,
+	.write_vfta		= e1000_write_vfta_generic,
+	.clear_vfta		= e1000_clear_vfta_generic,
+	.reset_hw		= e1000_reset_hw_80003es2lan,
+	.init_hw		= e1000_init_hw_80003es2lan,
+	.setup_link		= e1000e_setup_link_generic,
+	/* setup_physical_interface dependent on media type */
+	.setup_led		= e1000e_setup_led_generic,
+	.config_collision_dist	= e1000e_config_collision_dist_generic,
+	.rar_set		= e1000e_rar_set_generic,
+	.rar_get_count		= e1000e_rar_get_count_generic,
+};
+
+static const struct e1000_phy_operations es2_phy_ops = {
+	.acquire		= e1000_acquire_phy_80003es2lan,
+	.check_polarity		= e1000_check_polarity_m88,
+	.check_reset_block	= e1000e_check_reset_block_generic,
+	.commit			= e1000e_phy_sw_reset,
+	.force_speed_duplex	= e1000_phy_force_speed_duplex_80003es2lan,
+	.get_cfg_done		= e1000_get_cfg_done_80003es2lan,
+	.get_cable_length	= e1000_get_cable_length_80003es2lan,
+	.get_info		= e1000e_get_phy_info_m88,
+	.read_reg		= e1000_read_phy_reg_gg82563_80003es2lan,
+	.release		= e1000_release_phy_80003es2lan,
+	.reset			= e1000e_phy_hw_reset_generic,
+	.set_d0_lplu_state	= NULL,
+	.set_d3_lplu_state	= e1000e_set_d3_lplu_state,
+	.write_reg		= e1000_write_phy_reg_gg82563_80003es2lan,
+	.cfg_on_link_up		= e1000_cfg_on_link_up_80003es2lan,
+};
+
+static const struct e1000_nvm_operations es2_nvm_ops = {
+	.acquire		= e1000_acquire_nvm_80003es2lan,
+	.read			= e1000e_read_nvm_eerd,
+	.release		= e1000_release_nvm_80003es2lan,
+	.reload			= e1000e_reload_nvm_generic,
+	.update			= e1000e_update_nvm_checksum_generic,
+	.valid_led_default	= e1000e_valid_led_default,
+	.validate		= e1000e_validate_nvm_checksum_generic,
+	.write			= e1000_write_nvm_80003es2lan,
+};
+
+const struct e1000_info e1000_es2_info = {
+	.mac			= e1000_80003es2lan,
+	.flags			= FLAG_HAS_HW_VLAN_FILTER
+				  | FLAG_HAS_JUMBO_FRAMES
+				  | FLAG_HAS_WOL
+				  | FLAG_APME_IN_CTRL3
+				  | FLAG_HAS_CTRLEXT_ON_LOAD
+				  | FLAG_RX_NEEDS_RESTART /* errata */
+				  | FLAG_TARC_SET_BIT_ZERO /* errata */
+				  | FLAG_APME_CHECK_PORT_B
+				  | FLAG_DISABLE_FC_PAUSE_TIME, /* errata */
+	.flags2			= FLAG2_DMA_BURST,
+	.pba			= 38,
+	.max_hw_frame_size	= DEFAULT_JUMBO,
+	.get_variants		= e1000_get_variants_80003es2lan,
+	.mac_ops		= &es2_mac_ops,
+	.phy_ops		= &es2_phy_ops,
+	.nvm_ops		= &es2_nvm_ops,
+};