Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 780 insertions, 0 deletions

diff --git a/drivers/pinctrl/pinctrl-coh901.c b/drivers/pinctrl/pinctrl-coh901.c
new file mode 100644
index 000000000..7939b178c
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-coh901.c
@@ -0,0 +1,780 @@
+/*
+ * U300 GPIO module.
+ *
+ * Copyright (C) 2007-2012 ST-Ericsson AB
+ * License terms: GNU General Public License (GPL) version 2
+ * COH 901 571/3 - Used in DB3210 (U365 2.0) and DB3350 (U335 1.0)
+ * Author: Linus Walleij <linus.walleij@linaro.org>
+ * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
+ */
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/slab.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include "pinctrl-coh901.h"
+
+#define U300_GPIO_PORT_STRIDE				(0x30)
+/*
+ * Control Register 32bit (R/W)
+ * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
+ * gives the number of GPIO pins.
+ * bit 8-2  (mask 0x000001FC) contains the core version ID.
+ */
+#define U300_GPIO_CR					(0x00)
+#define U300_GPIO_CR_SYNC_SEL_ENABLE			(0x00000002UL)
+#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE			(0x00000001UL)
+#define U300_GPIO_PXPDIR				(0x04)
+#define U300_GPIO_PXPDOR				(0x08)
+#define U300_GPIO_PXPCR					(0x0C)
+#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK		(0x0000FFFFUL)
+#define U300_GPIO_PXPCR_PIN_MODE_MASK			(0x00000003UL)
+#define U300_GPIO_PXPCR_PIN_MODE_SHIFT			(0x00000002UL)
+#define U300_GPIO_PXPCR_PIN_MODE_INPUT			(0x00000000UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL	(0x00000001UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN	(0x00000002UL)
+#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE	(0x00000003UL)
+#define U300_GPIO_PXPER					(0x10)
+#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK	(0x000000FFUL)
+#define U300_GPIO_PXPER_PULL_UP_DISABLE			(0x00000001UL)
+#define U300_GPIO_PXIEV					(0x14)
+#define U300_GPIO_PXIEN					(0x18)
+#define U300_GPIO_PXIFR					(0x1C)
+#define U300_GPIO_PXICR					(0x20)
+#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK		(0x000000FFUL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_MASK			(0x00000001UL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE		(0x00000000UL)
+#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE		(0x00000001UL)
+
+/* 8 bits per port, no version has more than 7 ports */
+#define U300_GPIO_NUM_PORTS 7
+#define U300_GPIO_PINS_PER_PORT 8
+#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS)
+
+struct u300_gpio_port {
+	struct u300_gpio *gpio;
+	char name[8];
+	int irq;
+	int number;
+	u8 toggle_edge_mode;
+};
+
+struct u300_gpio {
+	struct gpio_chip chip;
+	struct u300_gpio_port ports[U300_GPIO_NUM_PORTS];
+	struct clk *clk;
+	void __iomem *base;
+	struct device *dev;
+	u32 stride;
+	/* Register offsets */
+	u32 pcr;
+	u32 dor;
+	u32 dir;
+	u32 per;
+	u32 icr;
+	u32 ien;
+	u32 iev;
+};
+
+/*
+ * Macro to expand to read a specific register found in the "gpio"
+ * struct. It requires the struct u300_gpio *gpio variable to exist in
+ * its context. It calculates the port offset from the given pin
+ * offset, muliplies by the port stride and adds the register offset
+ * so it provides a pointer to the desired register.
+ */
+#define U300_PIN_REG(pin, reg) \
+	(gpio->base + (pin >> 3) * gpio->stride + gpio->reg)
+
+/*
+ * Provides a bitmask for a specific gpio pin inside an 8-bit GPIO
+ * register.
+ */
+#define U300_PIN_BIT(pin) \
+	(1 << (pin & 0x07))
+
+struct u300_gpio_confdata {
+	u16 bias_mode;
+	bool output;
+	int outval;
+};
+
+#define U300_FLOATING_INPUT { \
+	.bias_mode = PIN_CONFIG_BIAS_HIGH_IMPEDANCE, \
+	.output = false, \
+}
+
+#define U300_PULL_UP_INPUT { \
+	.bias_mode = PIN_CONFIG_BIAS_PULL_UP, \
+	.output = false, \
+}
+
+#define U300_OUTPUT_LOW { \
+	.output = true, \
+	.outval = 0, \
+}
+
+#define U300_OUTPUT_HIGH { \
+	.output = true, \
+	.outval = 1, \
+}
+
+/* Initial configuration */
+static const struct u300_gpio_confdata __initconst
+bs335_gpio_config[U300_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
+	/* Port 0, pins 0-7 */
+	{
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_HIGH,
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+	},
+	/* Port 1, pins 0-7 */
+	{
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+		U300_PULL_UP_INPUT,
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_HIGH,
+		U300_OUTPUT_LOW,
+		U300_OUTPUT_LOW,
+	},
+	/* Port 2, pins 0-7 */
+	{
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_OUTPUT_LOW,
+		U300_PULL_UP_INPUT,
+		U300_OUTPUT_LOW,
+		U300_PULL_UP_INPUT,
+	},
+	/* Port 3, pins 0-7 */
+	{
+		U300_PULL_UP_INPUT,
+		U300_OUTPUT_LOW,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+	},
+	/* Port 4, pins 0-7 */
+	{
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+	},
+	/* Port 5, pins 0-7 */
+	{
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+	},
+	/* Port 6, pind 0-7 */
+	{
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+		U300_FLOATING_INPUT,
+	}
+};
+
+static int u300_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+	struct u300_gpio *gpio = gpiochip_get_data(chip);
+
+	return !!(readl(U300_PIN_REG(offset, dir)) & U300_PIN_BIT(offset));
+}
+
+static void u300_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
+{
+	struct u300_gpio *gpio = gpiochip_get_data(chip);
+	unsigned long flags;
+	u32 val;
+
+	local_irq_save(flags);
+
+	val = readl(U300_PIN_REG(offset, dor));
+	if (value)
+		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, dor));
+	else
+		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, dor));
+
+	local_irq_restore(flags);
+}
+
+static int u300_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
+{
+	struct u300_gpio *gpio = gpiochip_get_data(chip);
+	unsigned long flags;
+	u32 val;
+
+	local_irq_save(flags);
+	val = readl(U300_PIN_REG(offset, pcr));
+	/* Mask out this pin, note 2 bits per setting */
+	val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((offset & 0x07) << 1));
+	writel(val, U300_PIN_REG(offset, pcr));
+	local_irq_restore(flags);
+	return 0;
+}
+
+static int u300_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
+				      int value)
+{
+	struct u300_gpio *gpio = gpiochip_get_data(chip);
+	unsigned long flags;
+	u32 oldmode;
+	u32 val;
+
+	local_irq_save(flags);
+	val = readl(U300_PIN_REG(offset, pcr));
+	/*
+	 * Drive mode must be set by the special mode set function, set
+	 * push/pull mode by default if no mode has been selected.
+	 */
+	oldmode = val & (U300_GPIO_PXPCR_PIN_MODE_MASK <<
+			 ((offset & 0x07) << 1));
+	/* mode = 0 means input, else some mode is already set */
+	if (oldmode == 0) {
+		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK <<
+			 ((offset & 0x07) << 1));
+		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
+			<< ((offset & 0x07) << 1));
+		writel(val, U300_PIN_REG(offset, pcr));
+	}
+	u300_gpio_set(chip, offset, value);
+	local_irq_restore(flags);
+	return 0;
+}
+
+/* Returning -EINVAL means "supported but not available" */
+int u300_gpio_config_get(struct gpio_chip *chip,
+			 unsigned offset,
+			 unsigned long *config)
+{
+	struct u300_gpio *gpio = gpiochip_get_data(chip);
+	enum pin_config_param param = (enum pin_config_param) *config;
+	bool biasmode;
+	u32 drmode;
+
+	/* One bit per pin, clamp to bool range */
+	biasmode = !!(readl(U300_PIN_REG(offset, per)) & U300_PIN_BIT(offset));
+
+	/* Mask out the two bits for this pin and shift to bits 0,1 */
+	drmode = readl(U300_PIN_REG(offset, pcr));
+	drmode &= (U300_GPIO_PXPCR_PIN_MODE_MASK << ((offset & 0x07) << 1));
+	drmode >>= ((offset & 0x07) << 1);
+
+	switch (param) {
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+		*config = 0;
+		if (biasmode)
+			return 0;
+		else
+			return -EINVAL;
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		*config = 0;
+		if (!biasmode)
+			return 0;
+		else
+			return -EINVAL;
+		break;
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		*config = 0;
+		if (drmode == U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL)
+			return 0;
+		else
+			return -EINVAL;
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		*config = 0;
+		if (drmode == U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN)
+			return 0;
+		else
+			return -EINVAL;
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_SOURCE:
+		*config = 0;
+		if (drmode == U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE)
+			return 0;
+		else
+			return -EINVAL;
+		break;
+	default:
+		break;
+	}
+	return -ENOTSUPP;
+}
+
+int u300_gpio_config_set(struct gpio_chip *chip, unsigned offset,
+			 enum pin_config_param param)
+{
+	struct u300_gpio *gpio = gpiochip_get_data(chip);
+	unsigned long flags;
+	u32 val;
+
+	local_irq_save(flags);
+	switch (param) {
+	case PIN_CONFIG_BIAS_DISABLE:
+	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
+		val = readl(U300_PIN_REG(offset, per));
+		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
+		break;
+	case PIN_CONFIG_BIAS_PULL_UP:
+		val = readl(U300_PIN_REG(offset, per));
+		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
+		break;
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		val = readl(U300_PIN_REG(offset, pcr));
+		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
+			 << ((offset & 0x07) << 1));
+		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
+			<< ((offset & 0x07) << 1));
+		writel(val, U300_PIN_REG(offset, pcr));
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		val = readl(U300_PIN_REG(offset, pcr));
+		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
+			 << ((offset & 0x07) << 1));
+		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN
+			<< ((offset & 0x07) << 1));
+		writel(val, U300_PIN_REG(offset, pcr));
+		break;
+	case PIN_CONFIG_DRIVE_OPEN_SOURCE:
+		val = readl(U300_PIN_REG(offset, pcr));
+		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
+			 << ((offset & 0x07) << 1));
+		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE
+			<< ((offset & 0x07) << 1));
+		writel(val, U300_PIN_REG(offset, pcr));
+		break;
+	default:
+		local_irq_restore(flags);
+		dev_err(gpio->dev, "illegal configuration requested\n");
+		return -EINVAL;
+	}
+	local_irq_restore(flags);
+	return 0;
+}
+
+static const struct gpio_chip u300_gpio_chip = {
+	.label			= "u300-gpio-chip",
+	.owner			= THIS_MODULE,
+	.request		= gpiochip_generic_request,
+	.free			= gpiochip_generic_free,
+	.get			= u300_gpio_get,
+	.set			= u300_gpio_set,
+	.direction_input	= u300_gpio_direction_input,
+	.direction_output	= u300_gpio_direction_output,
+};
+
+static void u300_toggle_trigger(struct u300_gpio *gpio, unsigned offset)
+{
+	u32 val;
+
+	val = readl(U300_PIN_REG(offset, icr));
+	/* Set mode depending on state */
+	if (u300_gpio_get(&gpio->chip, offset)) {
+		/* High now, let's trigger on falling edge next then */
+		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+		dev_dbg(gpio->dev, "next IRQ on falling edge on pin %d\n",
+			offset);
+	} else {
+		/* Low now, let's trigger on rising edge next then */
+		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+		dev_dbg(gpio->dev, "next IRQ on rising edge on pin %d\n",
+			offset);
+	}
+}
+
+static int u300_gpio_irq_type(struct irq_data *d, unsigned trigger)
+{
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
+	struct u300_gpio *gpio = gpiochip_get_data(chip);
+	struct u300_gpio_port *port = &gpio->ports[d->hwirq >> 3];
+	int offset = d->hwirq;
+	u32 val;
+
+	if ((trigger & IRQF_TRIGGER_RISING) &&
+	    (trigger & IRQF_TRIGGER_FALLING)) {
+		/*
+		 * The GPIO block can only trigger on falling OR rising edges,
+		 * not both. So we need to toggle the mode whenever the pin
+		 * goes from one state to the other with a special state flag
+		 */
+		dev_dbg(gpio->dev,
+			"trigger on both rising and falling edge on pin %d\n",
+			offset);
+		port->toggle_edge_mode |= U300_PIN_BIT(offset);
+		u300_toggle_trigger(gpio, offset);
+	} else if (trigger & IRQF_TRIGGER_RISING) {
+		dev_dbg(gpio->dev, "trigger on rising edge on pin %d\n",
+			offset);
+		val = readl(U300_PIN_REG(offset, icr));
+		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+		port->toggle_edge_mode &= ~U300_PIN_BIT(offset);
+	} else if (trigger & IRQF_TRIGGER_FALLING) {
+		dev_dbg(gpio->dev, "trigger on falling edge on pin %d\n",
+			offset);
+		val = readl(U300_PIN_REG(offset, icr));
+		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
+		port->toggle_edge_mode &= ~U300_PIN_BIT(offset);
+	}
+
+	return 0;
+}
+
+static void u300_gpio_irq_enable(struct irq_data *d)
+{
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
+	struct u300_gpio *gpio = gpiochip_get_data(chip);
+	struct u300_gpio_port *port = &gpio->ports[d->hwirq >> 3];
+	int offset = d->hwirq;
+	u32 val;
+	unsigned long flags;
+
+	dev_dbg(gpio->dev, "enable IRQ for hwirq %lu on port %s, offset %d\n",
+		 d->hwirq, port->name, offset);
+	local_irq_save(flags);
+	val = readl(U300_PIN_REG(offset, ien));
+	writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
+	local_irq_restore(flags);
+}
+
+static void u300_gpio_irq_disable(struct irq_data *d)
+{
+	struct gpio_chip *chip = irq_data_get_irq_chip_data(d);
+	struct u300_gpio *gpio = gpiochip_get_data(chip);
+	int offset = d->hwirq;
+	u32 val;
+	unsigned long flags;
+
+	local_irq_save(flags);
+	val = readl(U300_PIN_REG(offset, ien));
+	writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
+	local_irq_restore(flags);
+}
+
+static struct irq_chip u300_gpio_irqchip = {
+	.name			= "u300-gpio-irqchip",
+	.irq_enable		= u300_gpio_irq_enable,
+	.irq_disable		= u300_gpio_irq_disable,
+	.irq_set_type		= u300_gpio_irq_type,
+};
+
+static void u300_gpio_irq_handler(struct irq_desc *desc)
+{
+	unsigned int irq = irq_desc_get_irq(desc);
+	struct irq_chip *parent_chip = irq_desc_get_chip(desc);
+	struct gpio_chip *chip = irq_desc_get_handler_data(desc);
+	struct u300_gpio *gpio = gpiochip_get_data(chip);
+	struct u300_gpio_port *port = &gpio->ports[irq - chip->base];
+	int pinoffset = port->number << 3; /* get the right stride */
+	unsigned long val;
+
+	chained_irq_enter(parent_chip, desc);
+
+	/* Read event register */
+	val = readl(U300_PIN_REG(pinoffset, iev));
+	/* Mask relevant bits */
+	val &= 0xFFU; /* 8 bits per port */
+	/* ACK IRQ (clear event) */
+	writel(val, U300_PIN_REG(pinoffset, iev));
+
+	/* Call IRQ handler */
+	if (val != 0) {
+		int irqoffset;
+
+		for_each_set_bit(irqoffset, &val, U300_GPIO_PINS_PER_PORT) {
+			int offset = pinoffset + irqoffset;
+			int pin_irq = irq_find_mapping(chip->irq.domain, offset);
+
+			dev_dbg(gpio->dev, "GPIO IRQ %d on pin %d\n",
+				pin_irq, offset);
+			generic_handle_irq(pin_irq);
+			/*
+			 * Triggering IRQ on both rising and falling edge
+			 * needs mockery
+			 */
+			if (port->toggle_edge_mode & U300_PIN_BIT(offset))
+				u300_toggle_trigger(gpio, offset);
+		}
+	}
+
+	chained_irq_exit(parent_chip, desc);
+}
+
+static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
+				      int offset,
+				      const struct u300_gpio_confdata *conf)
+{
+	/* Set mode: input or output */
+	if (conf->output) {
+		u300_gpio_direction_output(&gpio->chip, offset, conf->outval);
+
+		/* Deactivate bias mode for output */
+		u300_gpio_config_set(&gpio->chip, offset,
+				     PIN_CONFIG_BIAS_HIGH_IMPEDANCE);
+
+		/* Set drive mode for output */
+		u300_gpio_config_set(&gpio->chip, offset,
+				     PIN_CONFIG_DRIVE_PUSH_PULL);
+
+		dev_dbg(gpio->dev, "set up pin %d as output, value: %d\n",
+			offset, conf->outval);
+	} else {
+		u300_gpio_direction_input(&gpio->chip, offset);
+
+		/* Always set output low on input pins */
+		u300_gpio_set(&gpio->chip, offset, 0);
+
+		/* Set bias mode for input */
+		u300_gpio_config_set(&gpio->chip, offset, conf->bias_mode);
+
+		dev_dbg(gpio->dev, "set up pin %d as input, bias: %04x\n",
+			offset, conf->bias_mode);
+	}
+}
+
+static void __init u300_gpio_init_coh901571(struct u300_gpio *gpio)
+{
+	int i, j;
+
+	/* Write default config and values to all pins */
+	for (i = 0; i < U300_GPIO_NUM_PORTS; i++) {
+		for (j = 0; j < 8; j++) {
+			const struct u300_gpio_confdata *conf;
+			int offset = (i*8) + j;
+
+			conf = &bs335_gpio_config[i][j];
+			u300_gpio_init_pin(gpio, offset, conf);
+		}
+	}
+}
+
+/*
+ * Here we map a GPIO in the local gpio_chip pin space to a pin in
+ * the local pinctrl pin space. The pin controller used is
+ * pinctrl-u300.
+ */
+struct coh901_pinpair {
+	unsigned int offset;
+	unsigned int pin_base;
+};
+
+#define COH901_PINRANGE(a, b) { .offset = a, .pin_base = b }
+
+static struct coh901_pinpair coh901_pintable[] = {
+	COH901_PINRANGE(10, 426),
+	COH901_PINRANGE(11, 180),
+	COH901_PINRANGE(12, 165), /* MS/MMC card insertion */
+	COH901_PINRANGE(13, 179),
+	COH901_PINRANGE(14, 178),
+	COH901_PINRANGE(16, 194),
+	COH901_PINRANGE(17, 193),
+	COH901_PINRANGE(18, 192),
+	COH901_PINRANGE(19, 191),
+	COH901_PINRANGE(20, 186),
+	COH901_PINRANGE(21, 185),
+	COH901_PINRANGE(22, 184),
+	COH901_PINRANGE(23, 183),
+	COH901_PINRANGE(24, 182),
+	COH901_PINRANGE(25, 181),
+};
+
+static int __init u300_gpio_probe(struct platform_device *pdev)
+{
+	struct u300_gpio *gpio;
+	struct resource *memres;
+	int err = 0;
+	int portno;
+	u32 val;
+	u32 ifr;
+	int i;
+
+	gpio = devm_kzalloc(&pdev->dev, sizeof(struct u300_gpio), GFP_KERNEL);
+	if (gpio == NULL)
+		return -ENOMEM;
+
+	gpio->chip = u300_gpio_chip;
+	gpio->chip.ngpio = U300_GPIO_NUM_PORTS * U300_GPIO_PINS_PER_PORT;
+	gpio->chip.parent = &pdev->dev;
+	gpio->chip.base = 0;
+	gpio->dev = &pdev->dev;
+
+	memres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	gpio->base = devm_ioremap_resource(&pdev->dev, memres);
+	if (IS_ERR(gpio->base))
+		return PTR_ERR(gpio->base);
+
+	gpio->clk = devm_clk_get(gpio->dev, NULL);
+	if (IS_ERR(gpio->clk)) {
+		err = PTR_ERR(gpio->clk);
+		dev_err(gpio->dev, "could not get GPIO clock\n");
+		return err;
+	}
+
+	err = clk_prepare_enable(gpio->clk);
+	if (err) {
+		dev_err(gpio->dev, "could not enable GPIO clock\n");
+		return err;
+	}
+
+	dev_info(gpio->dev,
+		 "initializing GPIO Controller COH 901 571/3\n");
+	gpio->stride = U300_GPIO_PORT_STRIDE;
+	gpio->pcr = U300_GPIO_PXPCR;
+	gpio->dor = U300_GPIO_PXPDOR;
+	gpio->dir = U300_GPIO_PXPDIR;
+	gpio->per = U300_GPIO_PXPER;
+	gpio->icr = U300_GPIO_PXICR;
+	gpio->ien = U300_GPIO_PXIEN;
+	gpio->iev = U300_GPIO_PXIEV;
+	ifr = U300_GPIO_PXIFR;
+
+	val = readl(gpio->base + U300_GPIO_CR);
+	dev_info(gpio->dev, "COH901571/3 block version: %d, " \
+		 "number of cores: %d totalling %d pins\n",
+		 ((val & 0x000001FC) >> 2),
+		 ((val & 0x0000FE00) >> 9),
+		 ((val & 0x0000FE00) >> 9) * 8);
+	writel(U300_GPIO_CR_BLOCK_CLKRQ_ENABLE,
+	       gpio->base + U300_GPIO_CR);
+	u300_gpio_init_coh901571(gpio);
+
+#ifdef CONFIG_OF_GPIO
+	gpio->chip.of_node = pdev->dev.of_node;
+#endif
+	err = gpiochip_add_data(&gpio->chip, gpio);
+	if (err) {
+		dev_err(gpio->dev, "unable to add gpiochip: %d\n", err);
+		goto err_no_chip;
+	}
+
+	err = gpiochip_irqchip_add(&gpio->chip,
+				   &u300_gpio_irqchip,
+				   0,
+				   handle_simple_irq,
+				   IRQ_TYPE_EDGE_FALLING);
+	if (err) {
+		dev_err(gpio->dev, "no GPIO irqchip\n");
+		goto err_no_irqchip;
+	}
+
+	/* Add each port with its IRQ separately */
+	for (portno = 0 ; portno < U300_GPIO_NUM_PORTS; portno++) {
+		struct u300_gpio_port *port = &gpio->ports[portno];
+
+		snprintf(port->name, 8, "gpio%d", portno);
+		port->number = portno;
+		port->gpio = gpio;
+
+		port->irq = platform_get_irq(pdev, portno);
+
+		gpiochip_set_chained_irqchip(&gpio->chip,
+					     &u300_gpio_irqchip,
+					     port->irq,
+					     u300_gpio_irq_handler);
+
+		/* Turns off irq force (test register) for this port */
+		writel(0x0, gpio->base + portno * gpio->stride + ifr);
+	}
+	dev_dbg(gpio->dev, "initialized %d GPIO ports\n", portno);
+
+	/*
+	 * Add pinctrl pin ranges, the pin controller must be registered
+	 * at this point
+	 */
+	for (i = 0; i < ARRAY_SIZE(coh901_pintable); i++) {
+		struct coh901_pinpair *p = &coh901_pintable[i];
+
+		err = gpiochip_add_pin_range(&gpio->chip, "pinctrl-u300",
+					     p->offset, p->pin_base, 1);
+		if (err)
+			goto err_no_range;
+	}
+
+	platform_set_drvdata(pdev, gpio);
+
+	return 0;
+
+err_no_range:
+err_no_irqchip:
+	gpiochip_remove(&gpio->chip);
+err_no_chip:
+	clk_disable_unprepare(gpio->clk);
+	dev_err(&pdev->dev, "module ERROR:%d\n", err);
+	return err;
+}
+
+static int __exit u300_gpio_remove(struct platform_device *pdev)
+{
+	struct u300_gpio *gpio = platform_get_drvdata(pdev);
+
+	/* Turn off the GPIO block */
+	writel(0x00000000U, gpio->base + U300_GPIO_CR);
+
+	gpiochip_remove(&gpio->chip);
+	clk_disable_unprepare(gpio->clk);
+	return 0;
+}
+
+static const struct of_device_id u300_gpio_match[] = {
+	{ .compatible = "stericsson,gpio-coh901" },
+	{},
+};
+
+static struct platform_driver u300_gpio_driver = {
+	.driver		= {
+		.name	= "u300-gpio",
+		.of_match_table = u300_gpio_match,
+	},
+	.remove		= __exit_p(u300_gpio_remove),
+};
+
+static int __init u300_gpio_init(void)
+{
+	return platform_driver_probe(&u300_gpio_driver, u300_gpio_probe);
+}
+
+static void __exit u300_gpio_exit(void)
+{
+	platform_driver_unregister(&u300_gpio_driver);
+}
+
+arch_initcall(u300_gpio_init);
+module_exit(u300_gpio_exit);
+
+MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>");
+MODULE_DESCRIPTION("ST-Ericsson AB COH 901 335/COH 901 571/3 GPIO driver");
+MODULE_LICENSE("GPL");