Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 2713 insertions, 0 deletions

diff --git a/drivers/usb/gadget/udc/net2272.c b/drivers/usb/gadget/udc/net2272.c
new file mode 100644
index 000000000..077fa9304
--- /dev/null
+++ b/drivers/usb/gadget/udc/net2272.c
@@ -0,0 +1,2713 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Driver for PLX NET2272 USB device controller
+ *
+ * Copyright (C) 2005-2006 PLX Technology, Inc.
+ * Copyright (C) 2006-2011 Analog Devices, Inc.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/errno.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/list.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/prefetch.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/timer.h>
+#include <linux/usb.h>
+#include <linux/usb/ch9.h>
+#include <linux/usb/gadget.h>
+
+#include <asm/byteorder.h>
+#include <asm/unaligned.h>
+
+#include "net2272.h"
+
+#define DRIVER_DESC "PLX NET2272 USB Peripheral Controller"
+
+static const char driver_name[] = "net2272";
+static const char driver_vers[] = "2006 October 17/mainline";
+static const char driver_desc[] = DRIVER_DESC;
+
+static const char ep0name[] = "ep0";
+static const char * const ep_name[] = {
+	ep0name,
+	"ep-a", "ep-b", "ep-c",
+};
+
+#ifdef CONFIG_USB_NET2272_DMA
+/*
+ * use_dma: the NET2272 can use an external DMA controller.
+ * Note that since there is no generic DMA api, some functions,
+ * notably request_dma, start_dma, and cancel_dma will need to be
+ * modified for your platform's particular dma controller.
+ *
+ * If use_dma is disabled, pio will be used instead.
+ */
+static bool use_dma = 0;
+module_param(use_dma, bool, 0644);
+
+/*
+ * dma_ep: selects the endpoint for use with dma (1=ep-a, 2=ep-b)
+ * The NET2272 can only use dma for a single endpoint at a time.
+ * At some point this could be modified to allow either endpoint
+ * to take control of dma as it becomes available.
+ *
+ * Note that DMA should not be used on OUT endpoints unless it can
+ * be guaranteed that no short packets will arrive on an IN endpoint
+ * while the DMA operation is pending.  Otherwise the OUT DMA will
+ * terminate prematurely (See NET2272 Errata 630-0213-0101)
+ */
+static ushort dma_ep = 1;
+module_param(dma_ep, ushort, 0644);
+
+/*
+ * dma_mode: net2272 dma mode setting (see LOCCTL1 definiton):
+ *	mode 0 == Slow DREQ mode
+ *	mode 1 == Fast DREQ mode
+ *	mode 2 == Burst mode
+ */
+static ushort dma_mode = 2;
+module_param(dma_mode, ushort, 0644);
+#else
+#define use_dma 0
+#define dma_ep 1
+#define dma_mode 2
+#endif
+
+/*
+ * fifo_mode: net2272 buffer configuration:
+ *      mode 0 == ep-{a,b,c} 512db each
+ *      mode 1 == ep-a 1k, ep-{b,c} 512db
+ *      mode 2 == ep-a 1k, ep-b 1k, ep-c 512db
+ *      mode 3 == ep-a 1k, ep-b disabled, ep-c 512db
+ */
+static ushort fifo_mode = 0;
+module_param(fifo_mode, ushort, 0644);
+
+/*
+ * enable_suspend: When enabled, the driver will respond to
+ * USB suspend requests by powering down the NET2272.  Otherwise,
+ * USB suspend requests will be ignored.  This is acceptible for
+ * self-powered devices.  For bus powered devices set this to 1.
+ */
+static ushort enable_suspend = 0;
+module_param(enable_suspend, ushort, 0644);
+
+static void assert_out_naking(struct net2272_ep *ep, const char *where)
+{
+	u8 tmp;
+
+#ifndef DEBUG
+	return;
+#endif
+
+	tmp = net2272_ep_read(ep, EP_STAT0);
+	if ((tmp & (1 << NAK_OUT_PACKETS)) == 0) {
+		dev_dbg(ep->dev->dev, "%s %s %02x !NAK\n",
+			ep->ep.name, where, tmp);
+		net2272_ep_write(ep, EP_RSPSET, 1 << ALT_NAK_OUT_PACKETS);
+	}
+}
+#define ASSERT_OUT_NAKING(ep) assert_out_naking(ep, __func__)
+
+static void stop_out_naking(struct net2272_ep *ep)
+{
+	u8 tmp = net2272_ep_read(ep, EP_STAT0);
+
+	if ((tmp & (1 << NAK_OUT_PACKETS)) != 0)
+		net2272_ep_write(ep, EP_RSPCLR, 1 << ALT_NAK_OUT_PACKETS);
+}
+
+#define PIPEDIR(bAddress) (usb_pipein(bAddress) ? "in" : "out")
+
+static char *type_string(u8 bmAttributes)
+{
+	switch ((bmAttributes) & USB_ENDPOINT_XFERTYPE_MASK) {
+	case USB_ENDPOINT_XFER_BULK: return "bulk";
+	case USB_ENDPOINT_XFER_ISOC: return "iso";
+	case USB_ENDPOINT_XFER_INT:  return "intr";
+	default:                     return "control";
+	}
+}
+
+static char *buf_state_string(unsigned state)
+{
+	switch (state) {
+	case BUFF_FREE:  return "free";
+	case BUFF_VALID: return "valid";
+	case BUFF_LCL:   return "local";
+	case BUFF_USB:   return "usb";
+	default:         return "unknown";
+	}
+}
+
+static char *dma_mode_string(void)
+{
+	if (!use_dma)
+		return "PIO";
+	switch (dma_mode) {
+	case 0:  return "SLOW DREQ";
+	case 1:  return "FAST DREQ";
+	case 2:  return "BURST";
+	default: return "invalid";
+	}
+}
+
+static void net2272_dequeue_all(struct net2272_ep *);
+static int net2272_kick_dma(struct net2272_ep *, struct net2272_request *);
+static int net2272_fifo_status(struct usb_ep *);
+
+static const struct usb_ep_ops net2272_ep_ops;
+
+/*---------------------------------------------------------------------------*/
+
+static int
+net2272_enable(struct usb_ep *_ep, const struct usb_endpoint_descriptor *desc)
+{
+	struct net2272 *dev;
+	struct net2272_ep *ep;
+	u32 max;
+	u8 tmp;
+	unsigned long flags;
+
+	ep = container_of(_ep, struct net2272_ep, ep);
+	if (!_ep || !desc || ep->desc || _ep->name == ep0name
+			|| desc->bDescriptorType != USB_DT_ENDPOINT)
+		return -EINVAL;
+	dev = ep->dev;
+	if (!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN)
+		return -ESHUTDOWN;
+
+	max = usb_endpoint_maxp(desc);
+
+	spin_lock_irqsave(&dev->lock, flags);
+	_ep->maxpacket = max;
+	ep->desc = desc;
+
+	/* net2272_ep_reset() has already been called */
+	ep->stopped = 0;
+	ep->wedged = 0;
+
+	/* set speed-dependent max packet */
+	net2272_ep_write(ep, EP_MAXPKT0, max & 0xff);
+	net2272_ep_write(ep, EP_MAXPKT1, (max & 0xff00) >> 8);
+
+	/* set type, direction, address; reset fifo counters */
+	net2272_ep_write(ep, EP_STAT1, 1 << BUFFER_FLUSH);
+	tmp = usb_endpoint_type(desc);
+	if (usb_endpoint_xfer_bulk(desc)) {
+		/* catch some particularly blatant driver bugs */
+		if ((dev->gadget.speed == USB_SPEED_HIGH && max != 512) ||
+		    (dev->gadget.speed == USB_SPEED_FULL && max > 64)) {
+			spin_unlock_irqrestore(&dev->lock, flags);
+			return -ERANGE;
+		}
+	}
+	ep->is_iso = usb_endpoint_xfer_isoc(desc) ? 1 : 0;
+	tmp <<= ENDPOINT_TYPE;
+	tmp |= ((desc->bEndpointAddress & 0x0f) << ENDPOINT_NUMBER);
+	tmp |= usb_endpoint_dir_in(desc) << ENDPOINT_DIRECTION;
+	tmp |= (1 << ENDPOINT_ENABLE);
+
+	/* for OUT transfers, block the rx fifo until a read is posted */
+	ep->is_in = usb_endpoint_dir_in(desc);
+	if (!ep->is_in)
+		net2272_ep_write(ep, EP_RSPSET, 1 << ALT_NAK_OUT_PACKETS);
+
+	net2272_ep_write(ep, EP_CFG, tmp);
+
+	/* enable irqs */
+	tmp = (1 << ep->num) | net2272_read(dev, IRQENB0);
+	net2272_write(dev, IRQENB0, tmp);
+
+	tmp = (1 << DATA_PACKET_RECEIVED_INTERRUPT_ENABLE)
+		| (1 << DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE)
+		| net2272_ep_read(ep, EP_IRQENB);
+	net2272_ep_write(ep, EP_IRQENB, tmp);
+
+	tmp = desc->bEndpointAddress;
+	dev_dbg(dev->dev, "enabled %s (ep%d%s-%s) max %04x cfg %02x\n",
+		_ep->name, tmp & 0x0f, PIPEDIR(tmp),
+		type_string(desc->bmAttributes), max,
+		net2272_ep_read(ep, EP_CFG));
+
+	spin_unlock_irqrestore(&dev->lock, flags);
+	return 0;
+}
+
+static void net2272_ep_reset(struct net2272_ep *ep)
+{
+	u8 tmp;
+
+	ep->desc = NULL;
+	INIT_LIST_HEAD(&ep->queue);
+
+	usb_ep_set_maxpacket_limit(&ep->ep, ~0);
+	ep->ep.ops = &net2272_ep_ops;
+
+	/* disable irqs, endpoint */
+	net2272_ep_write(ep, EP_IRQENB, 0);
+
+	/* init to our chosen defaults, notably so that we NAK OUT
+	 * packets until the driver queues a read.
+	 */
+	tmp = (1 << NAK_OUT_PACKETS_MODE) | (1 << ALT_NAK_OUT_PACKETS);
+	net2272_ep_write(ep, EP_RSPSET, tmp);
+
+	tmp = (1 << INTERRUPT_MODE) | (1 << HIDE_STATUS_PHASE);
+	if (ep->num != 0)
+		tmp |= (1 << ENDPOINT_TOGGLE) | (1 << ENDPOINT_HALT);
+
+	net2272_ep_write(ep, EP_RSPCLR, tmp);
+
+	/* scrub most status bits, and flush any fifo state */
+	net2272_ep_write(ep, EP_STAT0,
+			  (1 << DATA_IN_TOKEN_INTERRUPT)
+			| (1 << DATA_OUT_TOKEN_INTERRUPT)
+			| (1 << DATA_PACKET_TRANSMITTED_INTERRUPT)
+			| (1 << DATA_PACKET_RECEIVED_INTERRUPT)
+			| (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT));
+
+	net2272_ep_write(ep, EP_STAT1,
+			    (1 << TIMEOUT)
+			  | (1 << USB_OUT_ACK_SENT)
+			  | (1 << USB_OUT_NAK_SENT)
+			  | (1 << USB_IN_ACK_RCVD)
+			  | (1 << USB_IN_NAK_SENT)
+			  | (1 << USB_STALL_SENT)
+			  | (1 << LOCAL_OUT_ZLP)
+			  | (1 << BUFFER_FLUSH));
+
+	/* fifo size is handled seperately */
+}
+
+static int net2272_disable(struct usb_ep *_ep)
+{
+	struct net2272_ep *ep;
+	unsigned long flags;
+
+	ep = container_of(_ep, struct net2272_ep, ep);
+	if (!_ep || !ep->desc || _ep->name == ep0name)
+		return -EINVAL;
+
+	spin_lock_irqsave(&ep->dev->lock, flags);
+	net2272_dequeue_all(ep);
+	net2272_ep_reset(ep);
+
+	dev_vdbg(ep->dev->dev, "disabled %s\n", _ep->name);
+
+	spin_unlock_irqrestore(&ep->dev->lock, flags);
+	return 0;
+}
+
+/*---------------------------------------------------------------------------*/
+
+static struct usb_request *
+net2272_alloc_request(struct usb_ep *_ep, gfp_t gfp_flags)
+{
+	struct net2272_request *req;
+
+	if (!_ep)
+		return NULL;
+
+	req = kzalloc(sizeof(*req), gfp_flags);
+	if (!req)
+		return NULL;
+
+	INIT_LIST_HEAD(&req->queue);
+
+	return &req->req;
+}
+
+static void
+net2272_free_request(struct usb_ep *_ep, struct usb_request *_req)
+{
+	struct net2272_request *req;
+
+	if (!_ep || !_req)
+		return;
+
+	req = container_of(_req, struct net2272_request, req);
+	WARN_ON(!list_empty(&req->queue));
+	kfree(req);
+}
+
+static void
+net2272_done(struct net2272_ep *ep, struct net2272_request *req, int status)
+{
+	struct net2272 *dev;
+	unsigned stopped = ep->stopped;
+
+	if (ep->num == 0) {
+		if (ep->dev->protocol_stall) {
+			ep->stopped = 1;
+			set_halt(ep);
+		}
+		allow_status(ep);
+	}
+
+	list_del_init(&req->queue);
+
+	if (req->req.status == -EINPROGRESS)
+		req->req.status = status;
+	else
+		status = req->req.status;
+
+	dev = ep->dev;
+	if (use_dma && ep->dma)
+		usb_gadget_unmap_request(&dev->gadget, &req->req,
+				ep->is_in);
+
+	if (status && status != -ESHUTDOWN)
+		dev_vdbg(dev->dev, "complete %s req %p stat %d len %u/%u buf %p\n",
+			ep->ep.name, &req->req, status,
+			req->req.actual, req->req.length, req->req.buf);
+
+	/* don't modify queue heads during completion callback */
+	ep->stopped = 1;
+	spin_unlock(&dev->lock);
+	usb_gadget_giveback_request(&ep->ep, &req->req);
+	spin_lock(&dev->lock);
+	ep->stopped = stopped;
+}
+
+static int
+net2272_write_packet(struct net2272_ep *ep, u8 *buf,
+	struct net2272_request *req, unsigned max)
+{
+	u16 __iomem *ep_data = net2272_reg_addr(ep->dev, EP_DATA);
+	u16 *bufp;
+	unsigned length, count;
+	u8 tmp;
+
+	length = min(req->req.length - req->req.actual, max);
+	req->req.actual += length;
+
+	dev_vdbg(ep->dev->dev, "write packet %s req %p max %u len %u avail %u\n",
+		ep->ep.name, req, max, length,
+		(net2272_ep_read(ep, EP_AVAIL1) << 8) | net2272_ep_read(ep, EP_AVAIL0));
+
+	count = length;
+	bufp = (u16 *)buf;
+
+	while (likely(count >= 2)) {
+		/* no byte-swap required; chip endian set during init */
+		writew(*bufp++, ep_data);
+		count -= 2;
+	}
+	buf = (u8 *)bufp;
+
+	/* write final byte by placing the NET2272 into 8-bit mode */
+	if (unlikely(count)) {
+		tmp = net2272_read(ep->dev, LOCCTL);
+		net2272_write(ep->dev, LOCCTL, tmp & ~(1 << DATA_WIDTH));
+		writeb(*buf, ep_data);
+		net2272_write(ep->dev, LOCCTL, tmp);
+	}
+	return length;
+}
+
+/* returns: 0: still running, 1: completed, negative: errno */
+static int
+net2272_write_fifo(struct net2272_ep *ep, struct net2272_request *req)
+{
+	u8 *buf;
+	unsigned count, max;
+	int status;
+
+	dev_vdbg(ep->dev->dev, "write_fifo %s actual %d len %d\n",
+		ep->ep.name, req->req.actual, req->req.length);
+
+	/*
+	 * Keep loading the endpoint until the final packet is loaded,
+	 * or the endpoint buffer is full.
+	 */
+ top:
+	/*
+	 * Clear interrupt status
+	 *  - Packet Transmitted interrupt will become set again when the
+	 *    host successfully takes another packet
+	 */
+	net2272_ep_write(ep, EP_STAT0, (1 << DATA_PACKET_TRANSMITTED_INTERRUPT));
+	while (!(net2272_ep_read(ep, EP_STAT0) & (1 << BUFFER_FULL))) {
+		buf = req->req.buf + req->req.actual;
+		prefetch(buf);
+
+		/* force pagesel */
+		net2272_ep_read(ep, EP_STAT0);
+
+		max = (net2272_ep_read(ep, EP_AVAIL1) << 8) |
+			(net2272_ep_read(ep, EP_AVAIL0));
+
+		if (max < ep->ep.maxpacket)
+			max = (net2272_ep_read(ep, EP_AVAIL1) << 8)
+				| (net2272_ep_read(ep, EP_AVAIL0));
+
+		count = net2272_write_packet(ep, buf, req, max);
+		/* see if we are done */
+		if (req->req.length == req->req.actual) {
+			/* validate short or zlp packet */
+			if (count < ep->ep.maxpacket)
+				set_fifo_bytecount(ep, 0);
+			net2272_done(ep, req, 0);
+
+			if (!list_empty(&ep->queue)) {
+				req = list_entry(ep->queue.next,
+						struct net2272_request,
+						queue);
+				status = net2272_kick_dma(ep, req);
+
+				if (status < 0)
+					if ((net2272_ep_read(ep, EP_STAT0)
+							& (1 << BUFFER_EMPTY)))
+						goto top;
+			}
+			return 1;
+		}
+		net2272_ep_write(ep, EP_STAT0, (1 << DATA_PACKET_TRANSMITTED_INTERRUPT));
+	}
+	return 0;
+}
+
+static void
+net2272_out_flush(struct net2272_ep *ep)
+{
+	ASSERT_OUT_NAKING(ep);
+
+	net2272_ep_write(ep, EP_STAT0, (1 << DATA_OUT_TOKEN_INTERRUPT)
+			| (1 << DATA_PACKET_RECEIVED_INTERRUPT));
+	net2272_ep_write(ep, EP_STAT1, 1 << BUFFER_FLUSH);
+}
+
+static int
+net2272_read_packet(struct net2272_ep *ep, u8 *buf,
+	struct net2272_request *req, unsigned avail)
+{
+	u16 __iomem *ep_data = net2272_reg_addr(ep->dev, EP_DATA);
+	unsigned is_short;
+	u16 *bufp;
+
+	req->req.actual += avail;
+
+	dev_vdbg(ep->dev->dev, "read packet %s req %p len %u avail %u\n",
+		ep->ep.name, req, avail,
+		(net2272_ep_read(ep, EP_AVAIL1) << 8) | net2272_ep_read(ep, EP_AVAIL0));
+
+	is_short = (avail < ep->ep.maxpacket);
+
+	if (unlikely(avail == 0)) {
+		/* remove any zlp from the buffer */
+		(void)readw(ep_data);
+		return is_short;
+	}
+
+	/* Ensure we get the final byte */
+	if (unlikely(avail % 2))
+		avail++;
+	bufp = (u16 *)buf;
+
+	do {
+		*bufp++ = readw(ep_data);
+		avail -= 2;
+	} while (avail);
+
+	/*
+	 * To avoid false endpoint available race condition must read
+	 * ep stat0 twice in the case of a short transfer
+	 */
+	if (net2272_ep_read(ep, EP_STAT0) & (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT))
+		net2272_ep_read(ep, EP_STAT0);
+
+	return is_short;
+}
+
+static int
+net2272_read_fifo(struct net2272_ep *ep, struct net2272_request *req)
+{
+	u8 *buf;
+	unsigned is_short;
+	int count;
+	int tmp;
+	int cleanup = 0;
+	int status = -1;
+
+	dev_vdbg(ep->dev->dev, "read_fifo %s actual %d len %d\n",
+		ep->ep.name, req->req.actual, req->req.length);
+
+ top:
+	do {
+		buf = req->req.buf + req->req.actual;
+		prefetchw(buf);
+
+		count = (net2272_ep_read(ep, EP_AVAIL1) << 8)
+			| net2272_ep_read(ep, EP_AVAIL0);
+
+		net2272_ep_write(ep, EP_STAT0,
+			(1 << SHORT_PACKET_TRANSFERRED_INTERRUPT) |
+			(1 << DATA_PACKET_RECEIVED_INTERRUPT));
+
+		tmp = req->req.length - req->req.actual;
+
+		if (count > tmp) {
+			if ((tmp % ep->ep.maxpacket) != 0) {
+				dev_err(ep->dev->dev,
+					"%s out fifo %d bytes, expected %d\n",
+					ep->ep.name, count, tmp);
+				cleanup = 1;
+			}
+			count = (tmp > 0) ? tmp : 0;
+		}
+
+		is_short = net2272_read_packet(ep, buf, req, count);
+
+		/* completion */
+		if (unlikely(cleanup || is_short ||
+				((req->req.actual == req->req.length)
+				 && !req->req.zero))) {
+
+			if (cleanup) {
+				net2272_out_flush(ep);
+				net2272_done(ep, req, -EOVERFLOW);
+			} else
+				net2272_done(ep, req, 0);
+
+			/* re-initialize endpoint transfer registers
+			 * otherwise they may result in erroneous pre-validation
+			 * for subsequent control reads
+			 */
+			if (unlikely(ep->num == 0)) {
+				net2272_ep_write(ep, EP_TRANSFER2, 0);
+				net2272_ep_write(ep, EP_TRANSFER1, 0);
+				net2272_ep_write(ep, EP_TRANSFER0, 0);
+			}
+
+			if (!list_empty(&ep->queue)) {
+				req = list_entry(ep->queue.next,
+					struct net2272_request, queue);
+				status = net2272_kick_dma(ep, req);
+				if ((status < 0) &&
+				    !(net2272_ep_read(ep, EP_STAT0) & (1 << BUFFER_EMPTY)))
+					goto top;
+			}
+			return 1;
+		}
+	} while (!(net2272_ep_read(ep, EP_STAT0) & (1 << BUFFER_EMPTY)));
+
+	return 0;
+}
+
+static void
+net2272_pio_advance(struct net2272_ep *ep)
+{
+	struct net2272_request *req;
+
+	if (unlikely(list_empty(&ep->queue)))
+		return;
+
+	req = list_entry(ep->queue.next, struct net2272_request, queue);
+	(ep->is_in ? net2272_write_fifo : net2272_read_fifo)(ep, req);
+}
+
+/* returns 0 on success, else negative errno */
+static int
+net2272_request_dma(struct net2272 *dev, unsigned ep, u32 buf,
+	unsigned len, unsigned dir)
+{
+	dev_vdbg(dev->dev, "request_dma ep %d buf %08x len %d dir %d\n",
+		ep, buf, len, dir);
+
+	/* The NET2272 only supports a single dma channel */
+	if (dev->dma_busy)
+		return -EBUSY;
+	/*
+	 * EP_TRANSFER (used to determine the number of bytes received
+	 * in an OUT transfer) is 24 bits wide; don't ask for more than that.
+	 */
+	if ((dir == 1) && (len > 0x1000000))
+		return -EINVAL;
+
+	dev->dma_busy = 1;
+
+	/* initialize platform's dma */
+#ifdef CONFIG_USB_PCI
+	/* NET2272 addr, buffer addr, length, etc. */
+	switch (dev->dev_id) {
+	case PCI_DEVICE_ID_RDK1:
+		/* Setup PLX 9054 DMA mode */
+		writel((1 << LOCAL_BUS_WIDTH) |
+			(1 << TA_READY_INPUT_ENABLE) |
+			(0 << LOCAL_BURST_ENABLE) |
+			(1 << DONE_INTERRUPT_ENABLE) |
+			(1 << LOCAL_ADDRESSING_MODE) |
+			(1 << DEMAND_MODE) |
+			(1 << DMA_EOT_ENABLE) |
+			(1 << FAST_SLOW_TERMINATE_MODE_SELECT) |
+			(1 << DMA_CHANNEL_INTERRUPT_SELECT),
+			dev->rdk1.plx9054_base_addr + DMAMODE0);
+
+		writel(0x100000, dev->rdk1.plx9054_base_addr + DMALADR0);
+		writel(buf, dev->rdk1.plx9054_base_addr + DMAPADR0);
+		writel(len, dev->rdk1.plx9054_base_addr + DMASIZ0);
+		writel((dir << DIRECTION_OF_TRANSFER) |
+			(1 << INTERRUPT_AFTER_TERMINAL_COUNT),
+			dev->rdk1.plx9054_base_addr + DMADPR0);
+		writel((1 << LOCAL_DMA_CHANNEL_0_INTERRUPT_ENABLE) |
+			readl(dev->rdk1.plx9054_base_addr + INTCSR),
+			dev->rdk1.plx9054_base_addr + INTCSR);
+
+		break;
+	}
+#endif
+
+	net2272_write(dev, DMAREQ,
+		(0 << DMA_BUFFER_VALID) |
+		(1 << DMA_REQUEST_ENABLE) |
+		(1 << DMA_CONTROL_DACK) |
+		(dev->dma_eot_polarity << EOT_POLARITY) |
+		(dev->dma_dack_polarity << DACK_POLARITY) |
+		(dev->dma_dreq_polarity << DREQ_POLARITY) |
+		((ep >> 1) << DMA_ENDPOINT_SELECT));
+
+	(void) net2272_read(dev, SCRATCH);
+
+	return 0;
+}
+
+static void
+net2272_start_dma(struct net2272 *dev)
+{
+	/* start platform's dma controller */
+#ifdef CONFIG_USB_PCI
+	switch (dev->dev_id) {
+	case PCI_DEVICE_ID_RDK1:
+		writeb((1 << CHANNEL_ENABLE) | (1 << CHANNEL_START),
+			dev->rdk1.plx9054_base_addr + DMACSR0);
+		break;
+	}
+#endif
+}
+
+/* returns 0 on success, else negative errno */
+static int
+net2272_kick_dma(struct net2272_ep *ep, struct net2272_request *req)
+{
+	unsigned size;
+	u8 tmp;
+
+	if (!use_dma || (ep->num < 1) || (ep->num > 2) || !ep->dma)
+		return -EINVAL;
+
+	/* don't use dma for odd-length transfers
+	 * otherwise, we'd need to deal with the last byte with pio
+	 */
+	if (req->req.length & 1)
+		return -EINVAL;
+
+	dev_vdbg(ep->dev->dev, "kick_dma %s req %p dma %08llx\n",
+		ep->ep.name, req, (unsigned long long) req->req.dma);
+
+	net2272_ep_write(ep, EP_RSPSET, 1 << ALT_NAK_OUT_PACKETS);
+
+	/* The NET2272 can only use DMA on one endpoint at a time */
+	if (ep->dev->dma_busy)
+		return -EBUSY;
+
+	/* Make sure we only DMA an even number of bytes (we'll use
+	 * pio to complete the transfer)
+	 */
+	size = req->req.length;
+	size &= ~1;
+
+	/* device-to-host transfer */
+	if (ep->is_in) {
+		/* initialize platform's dma controller */
+		if (net2272_request_dma(ep->dev, ep->num, req->req.dma, size, 0))
+			/* unable to obtain DMA channel; return error and use pio mode */
+			return -EBUSY;
+		req->req.actual += size;
+
+	/* host-to-device transfer */
+	} else {
+		tmp = net2272_ep_read(ep, EP_STAT0);
+
+		/* initialize platform's dma controller */
+		if (net2272_request_dma(ep->dev, ep->num, req->req.dma, size, 1))
+			/* unable to obtain DMA channel; return error and use pio mode */
+			return -EBUSY;
+
+		if (!(tmp & (1 << BUFFER_EMPTY)))
+			ep->not_empty = 1;
+		else
+			ep->not_empty = 0;
+
+
+		/* allow the endpoint's buffer to fill */
+		net2272_ep_write(ep, EP_RSPCLR, 1 << ALT_NAK_OUT_PACKETS);
+
+		/* this transfer completed and data's already in the fifo
+		 * return error so pio gets used.
+		 */
+		if (tmp & (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT)) {
+
+			/* deassert dreq */
+			net2272_write(ep->dev, DMAREQ,
+				(0 << DMA_BUFFER_VALID) |
+				(0 << DMA_REQUEST_ENABLE) |
+				(1 << DMA_CONTROL_DACK) |
+				(ep->dev->dma_eot_polarity << EOT_POLARITY) |
+				(ep->dev->dma_dack_polarity << DACK_POLARITY) |
+				(ep->dev->dma_dreq_polarity << DREQ_POLARITY) |
+				((ep->num >> 1) << DMA_ENDPOINT_SELECT));
+
+			return -EBUSY;
+		}
+	}
+
+	/* Don't use per-packet interrupts: use dma interrupts only */
+	net2272_ep_write(ep, EP_IRQENB, 0);
+
+	net2272_start_dma(ep->dev);
+
+	return 0;
+}
+
+static void net2272_cancel_dma(struct net2272 *dev)
+{
+#ifdef CONFIG_USB_PCI
+	switch (dev->dev_id) {
+	case PCI_DEVICE_ID_RDK1:
+		writeb(0, dev->rdk1.plx9054_base_addr + DMACSR0);
+		writeb(1 << CHANNEL_ABORT, dev->rdk1.plx9054_base_addr + DMACSR0);
+		while (!(readb(dev->rdk1.plx9054_base_addr + DMACSR0) &
+		         (1 << CHANNEL_DONE)))
+			continue;	/* wait for dma to stabalize */
+
+		/* dma abort generates an interrupt */
+		writeb(1 << CHANNEL_CLEAR_INTERRUPT,
+			dev->rdk1.plx9054_base_addr + DMACSR0);
+		break;
+	}
+#endif
+
+	dev->dma_busy = 0;
+}
+
+/*---------------------------------------------------------------------------*/
+
+static int
+net2272_queue(struct usb_ep *_ep, struct usb_request *_req, gfp_t gfp_flags)
+{
+	struct net2272_request *req;
+	struct net2272_ep *ep;
+	struct net2272 *dev;
+	unsigned long flags;
+	int status = -1;
+	u8 s;
+
+	req = container_of(_req, struct net2272_request, req);
+	if (!_req || !_req->complete || !_req->buf
+			|| !list_empty(&req->queue))
+		return -EINVAL;
+	ep = container_of(_ep, struct net2272_ep, ep);
+	if (!_ep || (!ep->desc && ep->num != 0))
+		return -EINVAL;
+	dev = ep->dev;
+	if (!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN)
+		return -ESHUTDOWN;
+
+	/* set up dma mapping in case the caller didn't */
+	if (use_dma && ep->dma) {
+		status = usb_gadget_map_request(&dev->gadget, _req,
+				ep->is_in);
+		if (status)
+			return status;
+	}
+
+	dev_vdbg(dev->dev, "%s queue req %p, len %d buf %p dma %08llx %s\n",
+		_ep->name, _req, _req->length, _req->buf,
+		(unsigned long long) _req->dma, _req->zero ? "zero" : "!zero");
+
+	spin_lock_irqsave(&dev->lock, flags);
+
+	_req->status = -EINPROGRESS;
+	_req->actual = 0;
+
+	/* kickstart this i/o queue? */
+	if (list_empty(&ep->queue) && !ep->stopped) {
+		/* maybe there's no control data, just status ack */
+		if (ep->num == 0 && _req->length == 0) {
+			net2272_done(ep, req, 0);
+			dev_vdbg(dev->dev, "%s status ack\n", ep->ep.name);
+			goto done;
+		}
+
+		/* Return zlp, don't let it block subsequent packets */
+		s = net2272_ep_read(ep, EP_STAT0);
+		if (s & (1 << BUFFER_EMPTY)) {
+			/* Buffer is empty check for a blocking zlp, handle it */
+			if ((s & (1 << NAK_OUT_PACKETS)) &&
+			    net2272_ep_read(ep, EP_STAT1) & (1 << LOCAL_OUT_ZLP)) {
+				dev_dbg(dev->dev, "WARNING: returning ZLP short packet termination!\n");
+				/*
+				 * Request is going to terminate with a short packet ...
+				 * hope the client is ready for it!
+				 */
+				status = net2272_read_fifo(ep, req);
+				/* clear short packet naking */
+				net2272_ep_write(ep, EP_STAT0, (1 << NAK_OUT_PACKETS));
+				goto done;
+			}
+		}
+
+		/* try dma first */
+		status = net2272_kick_dma(ep, req);
+
+		if (status < 0) {
+			/* dma failed (most likely in use by another endpoint)
+			 * fallback to pio
+			 */
+			status = 0;
+
+			if (ep->is_in)
+				status = net2272_write_fifo(ep, req);
+			else {
+				s = net2272_ep_read(ep, EP_STAT0);
+				if ((s & (1 << BUFFER_EMPTY)) == 0)
+					status = net2272_read_fifo(ep, req);
+			}
+
+			if (unlikely(status != 0)) {
+				if (status > 0)
+					status = 0;
+				req = NULL;
+			}
+		}
+	}
+	if (likely(req))
+		list_add_tail(&req->queue, &ep->queue);
+
+	if (likely(!list_empty(&ep->queue)))
+		net2272_ep_write(ep, EP_RSPCLR, 1 << ALT_NAK_OUT_PACKETS);
+ done:
+	spin_unlock_irqrestore(&dev->lock, flags);
+
+	return 0;
+}
+
+/* dequeue ALL requests */
+static void
+net2272_dequeue_all(struct net2272_ep *ep)
+{
+	struct net2272_request *req;
+
+	/* called with spinlock held */
+	ep->stopped = 1;
+
+	while (!list_empty(&ep->queue)) {
+		req = list_entry(ep->queue.next,
+				struct net2272_request,
+				queue);
+		net2272_done(ep, req, -ESHUTDOWN);
+	}
+}
+
+/* dequeue JUST ONE request */
+static int
+net2272_dequeue(struct usb_ep *_ep, struct usb_request *_req)
+{
+	struct net2272_ep *ep;
+	struct net2272_request *req;
+	unsigned long flags;
+	int stopped;
+
+	ep = container_of(_ep, struct net2272_ep, ep);
+	if (!_ep || (!ep->desc && ep->num != 0) || !_req)
+		return -EINVAL;
+
+	spin_lock_irqsave(&ep->dev->lock, flags);
+	stopped = ep->stopped;
+	ep->stopped = 1;
+
+	/* make sure it's still queued on this endpoint */
+	list_for_each_entry(req, &ep->queue, queue) {
+		if (&req->req == _req)
+			break;
+	}
+	if (&req->req != _req) {
+		ep->stopped = stopped;
+		spin_unlock_irqrestore(&ep->dev->lock, flags);
+		return -EINVAL;
+	}
+
+	/* queue head may be partially complete */
+	if (ep->queue.next == &req->queue) {
+		dev_dbg(ep->dev->dev, "unlink (%s) pio\n", _ep->name);
+		net2272_done(ep, req, -ECONNRESET);
+	}
+	req = NULL;
+	ep->stopped = stopped;
+
+	spin_unlock_irqrestore(&ep->dev->lock, flags);
+	return 0;
+}
+
+/*---------------------------------------------------------------------------*/
+
+static int
+net2272_set_halt_and_wedge(struct usb_ep *_ep, int value, int wedged)
+{
+	struct net2272_ep *ep;
+	unsigned long flags;
+	int ret = 0;
+
+	ep = container_of(_ep, struct net2272_ep, ep);
+	if (!_ep || (!ep->desc && ep->num != 0))
+		return -EINVAL;
+	if (!ep->dev->driver || ep->dev->gadget.speed == USB_SPEED_UNKNOWN)
+		return -ESHUTDOWN;
+	if (ep->desc /* not ep0 */ && usb_endpoint_xfer_isoc(ep->desc))
+		return -EINVAL;
+
+	spin_lock_irqsave(&ep->dev->lock, flags);
+	if (!list_empty(&ep->queue))
+		ret = -EAGAIN;
+	else if (ep->is_in && value && net2272_fifo_status(_ep) != 0)
+		ret = -EAGAIN;
+	else {
+		dev_vdbg(ep->dev->dev, "%s %s %s\n", _ep->name,
+			value ? "set" : "clear",
+			wedged ? "wedge" : "halt");
+		/* set/clear */
+		if (value) {
+			if (ep->num == 0)
+				ep->dev->protocol_stall = 1;
+			else
+				set_halt(ep);
+			if (wedged)
+				ep->wedged = 1;
+		} else {
+			clear_halt(ep);
+			ep->wedged = 0;
+		}
+	}
+	spin_unlock_irqrestore(&ep->dev->lock, flags);
+
+	return ret;
+}
+
+static int
+net2272_set_halt(struct usb_ep *_ep, int value)
+{
+	return net2272_set_halt_and_wedge(_ep, value, 0);
+}
+
+static int
+net2272_set_wedge(struct usb_ep *_ep)
+{
+	if (!_ep || _ep->name == ep0name)
+		return -EINVAL;
+	return net2272_set_halt_and_wedge(_ep, 1, 1);
+}
+
+static int
+net2272_fifo_status(struct usb_ep *_ep)
+{
+	struct net2272_ep *ep;
+	u16 avail;
+
+	ep = container_of(_ep, struct net2272_ep, ep);
+	if (!_ep || (!ep->desc && ep->num != 0))
+		return -ENODEV;
+	if (!ep->dev->driver || ep->dev->gadget.speed == USB_SPEED_UNKNOWN)
+		return -ESHUTDOWN;
+
+	avail = net2272_ep_read(ep, EP_AVAIL1) << 8;
+	avail |= net2272_ep_read(ep, EP_AVAIL0);
+	if (avail > ep->fifo_size)
+		return -EOVERFLOW;
+	if (ep->is_in)
+		avail = ep->fifo_size - avail;
+	return avail;
+}
+
+static void
+net2272_fifo_flush(struct usb_ep *_ep)
+{
+	struct net2272_ep *ep;
+
+	ep = container_of(_ep, struct net2272_ep, ep);
+	if (!_ep || (!ep->desc && ep->num != 0))
+		return;
+	if (!ep->dev->driver || ep->dev->gadget.speed == USB_SPEED_UNKNOWN)
+		return;
+
+	net2272_ep_write(ep, EP_STAT1, 1 << BUFFER_FLUSH);
+}
+
+static const struct usb_ep_ops net2272_ep_ops = {
+	.enable        = net2272_enable,
+	.disable       = net2272_disable,
+
+	.alloc_request = net2272_alloc_request,
+	.free_request  = net2272_free_request,
+
+	.queue         = net2272_queue,
+	.dequeue       = net2272_dequeue,
+
+	.set_halt      = net2272_set_halt,
+	.set_wedge     = net2272_set_wedge,
+	.fifo_status   = net2272_fifo_status,
+	.fifo_flush    = net2272_fifo_flush,
+};
+
+/*---------------------------------------------------------------------------*/
+
+static int
+net2272_get_frame(struct usb_gadget *_gadget)
+{
+	struct net2272 *dev;
+	unsigned long flags;
+	u16 ret;
+
+	if (!_gadget)
+		return -ENODEV;
+	dev = container_of(_gadget, struct net2272, gadget);
+	spin_lock_irqsave(&dev->lock, flags);
+
+	ret = net2272_read(dev, FRAME1) << 8;
+	ret |= net2272_read(dev, FRAME0);
+
+	spin_unlock_irqrestore(&dev->lock, flags);
+	return ret;
+}
+
+static int
+net2272_wakeup(struct usb_gadget *_gadget)
+{
+	struct net2272 *dev;
+	u8 tmp;
+	unsigned long flags;
+
+	if (!_gadget)
+		return 0;
+	dev = container_of(_gadget, struct net2272, gadget);
+
+	spin_lock_irqsave(&dev->lock, flags);
+	tmp = net2272_read(dev, USBCTL0);
+	if (tmp & (1 << IO_WAKEUP_ENABLE))
+		net2272_write(dev, USBCTL1, (1 << GENERATE_RESUME));
+
+	spin_unlock_irqrestore(&dev->lock, flags);
+
+	return 0;
+}
+
+static int
+net2272_set_selfpowered(struct usb_gadget *_gadget, int value)
+{
+	if (!_gadget)
+		return -ENODEV;
+
+	_gadget->is_selfpowered = (value != 0);
+
+	return 0;
+}
+
+static int
+net2272_pullup(struct usb_gadget *_gadget, int is_on)
+{
+	struct net2272 *dev;
+	u8 tmp;
+	unsigned long flags;
+
+	if (!_gadget)
+		return -ENODEV;
+	dev = container_of(_gadget, struct net2272, gadget);
+
+	spin_lock_irqsave(&dev->lock, flags);
+	tmp = net2272_read(dev, USBCTL0);
+	dev->softconnect = (is_on != 0);
+	if (is_on)
+		tmp |= (1 << USB_DETECT_ENABLE);
+	else
+		tmp &= ~(1 << USB_DETECT_ENABLE);
+	net2272_write(dev, USBCTL0, tmp);
+	spin_unlock_irqrestore(&dev->lock, flags);
+
+	return 0;
+}
+
+static int net2272_start(struct usb_gadget *_gadget,
+		struct usb_gadget_driver *driver);
+static int net2272_stop(struct usb_gadget *_gadget);
+
+static const struct usb_gadget_ops net2272_ops = {
+	.get_frame	= net2272_get_frame,
+	.wakeup		= net2272_wakeup,
+	.set_selfpowered = net2272_set_selfpowered,
+	.pullup		= net2272_pullup,
+	.udc_start	= net2272_start,
+	.udc_stop	= net2272_stop,
+};
+
+/*---------------------------------------------------------------------------*/
+
+static ssize_t
+registers_show(struct device *_dev, struct device_attribute *attr, char *buf)
+{
+	struct net2272 *dev;
+	char *next;
+	unsigned size, t;
+	unsigned long flags;
+	u8 t1, t2;
+	int i;
+	const char *s;
+
+	dev = dev_get_drvdata(_dev);
+	next = buf;
+	size = PAGE_SIZE;
+	spin_lock_irqsave(&dev->lock, flags);
+
+	if (dev->driver)
+		s = dev->driver->driver.name;
+	else
+		s = "(none)";
+
+	/* Main Control Registers */
+	t = scnprintf(next, size, "%s version %s,"
+		"chiprev %02x, locctl %02x\n"
+		"irqenb0 %02x irqenb1 %02x "
+		"irqstat0 %02x irqstat1 %02x\n",
+		driver_name, driver_vers, dev->chiprev,
+		net2272_read(dev, LOCCTL),
+		net2272_read(dev, IRQENB0),
+		net2272_read(dev, IRQENB1),
+		net2272_read(dev, IRQSTAT0),
+		net2272_read(dev, IRQSTAT1));
+	size -= t;
+	next += t;
+
+	/* DMA */
+	t1 = net2272_read(dev, DMAREQ);
+	t = scnprintf(next, size, "\ndmareq %02x: %s %s%s%s%s\n",
+		t1, ep_name[(t1 & 0x01) + 1],
+		t1 & (1 << DMA_CONTROL_DACK) ? "dack " : "",
+		t1 & (1 << DMA_REQUEST_ENABLE) ? "reqenb " : "",
+		t1 & (1 << DMA_REQUEST) ? "req " : "",
+		t1 & (1 << DMA_BUFFER_VALID) ? "valid " : "");
+	size -= t;
+	next += t;
+
+	/* USB Control Registers */
+	t1 = net2272_read(dev, USBCTL1);
+	if (t1 & (1 << VBUS_PIN)) {
+		if (t1 & (1 << USB_HIGH_SPEED))
+			s = "high speed";
+		else if (dev->gadget.speed == USB_SPEED_UNKNOWN)
+			s = "powered";
+		else
+			s = "full speed";
+	} else
+		s = "not attached";
+	t = scnprintf(next, size,
+		"usbctl0 %02x usbctl1 %02x addr 0x%02x (%s)\n",
+		net2272_read(dev, USBCTL0), t1,
+		net2272_read(dev, OURADDR), s);
+	size -= t;
+	next += t;
+
+	/* Endpoint Registers */
+	for (i = 0; i < 4; ++i) {
+		struct net2272_ep *ep;
+
+		ep = &dev->ep[i];
+		if (i && !ep->desc)
+			continue;
+
+		t1 = net2272_ep_read(ep, EP_CFG);
+		t2 = net2272_ep_read(ep, EP_RSPSET);
+		t = scnprintf(next, size,
+			"\n%s\tcfg %02x rsp (%02x) %s%s%s%s%s%s%s%s"
+			"irqenb %02x\n",
+			ep->ep.name, t1, t2,
+			(t2 & (1 << ALT_NAK_OUT_PACKETS)) ? "NAK " : "",
+			(t2 & (1 << HIDE_STATUS_PHASE)) ? "hide " : "",
+			(t2 & (1 << AUTOVALIDATE)) ? "auto " : "",
+			(t2 & (1 << INTERRUPT_MODE)) ? "interrupt " : "",
+			(t2 & (1 << CONTROL_STATUS_PHASE_HANDSHAKE)) ? "status " : "",
+			(t2 & (1 << NAK_OUT_PACKETS_MODE)) ? "NAKmode " : "",
+			(t2 & (1 << ENDPOINT_TOGGLE)) ? "DATA1 " : "DATA0 ",
+			(t2 & (1 << ENDPOINT_HALT)) ? "HALT " : "",
+			net2272_ep_read(ep, EP_IRQENB));
+		size -= t;
+		next += t;
+
+		t = scnprintf(next, size,
+			"\tstat0 %02x stat1 %02x avail %04x "
+			"(ep%d%s-%s)%s\n",
+			net2272_ep_read(ep, EP_STAT0),
+			net2272_ep_read(ep, EP_STAT1),
+			(net2272_ep_read(ep, EP_AVAIL1) << 8) | net2272_ep_read(ep, EP_AVAIL0),
+			t1 & 0x0f,
+			ep->is_in ? "in" : "out",
+			type_string(t1 >> 5),
+			ep->stopped ? "*" : "");
+		size -= t;
+		next += t;
+
+		t = scnprintf(next, size,
+			"\tep_transfer %06x\n",
+			((net2272_ep_read(ep, EP_TRANSFER2) & 0xff) << 16) |
+			((net2272_ep_read(ep, EP_TRANSFER1) & 0xff) << 8) |
+			((net2272_ep_read(ep, EP_TRANSFER0) & 0xff)));
+		size -= t;
+		next += t;
+
+		t1 = net2272_ep_read(ep, EP_BUFF_STATES) & 0x03;
+		t2 = (net2272_ep_read(ep, EP_BUFF_STATES) >> 2) & 0x03;
+		t = scnprintf(next, size,
+			"\tbuf-a %s buf-b %s\n",
+			buf_state_string(t1),
+			buf_state_string(t2));
+		size -= t;
+		next += t;
+	}
+
+	spin_unlock_irqrestore(&dev->lock, flags);
+
+	return PAGE_SIZE - size;
+}
+static DEVICE_ATTR_RO(registers);
+
+/*---------------------------------------------------------------------------*/
+
+static void
+net2272_set_fifo_mode(struct net2272 *dev, int mode)
+{
+	u8 tmp;
+
+	tmp = net2272_read(dev, LOCCTL) & 0x3f;
+	tmp |= (mode << 6);
+	net2272_write(dev, LOCCTL, tmp);
+
+	INIT_LIST_HEAD(&dev->gadget.ep_list);
+
+	/* always ep-a, ep-c ... maybe not ep-b */
+	list_add_tail(&dev->ep[1].ep.ep_list, &dev->gadget.ep_list);
+
+	switch (mode) {
+	case 0:
+		list_add_tail(&dev->ep[2].ep.ep_list, &dev->gadget.ep_list);
+		dev->ep[1].fifo_size = dev->ep[2].fifo_size = 512;
+		break;
+	case 1:
+		list_add_tail(&dev->ep[2].ep.ep_list, &dev->gadget.ep_list);
+		dev->ep[1].fifo_size = 1024;
+		dev->ep[2].fifo_size = 512;
+		break;
+	case 2:
+		list_add_tail(&dev->ep[2].ep.ep_list, &dev->gadget.ep_list);
+		dev->ep[1].fifo_size = dev->ep[2].fifo_size = 1024;
+		break;
+	case 3:
+		dev->ep[1].fifo_size = 1024;
+		break;
+	}
+
+	/* ep-c is always 2 512 byte buffers */
+	list_add_tail(&dev->ep[3].ep.ep_list, &dev->gadget.ep_list);
+	dev->ep[3].fifo_size = 512;
+}
+
+/*---------------------------------------------------------------------------*/
+
+static void
+net2272_usb_reset(struct net2272 *dev)
+{
+	dev->gadget.speed = USB_SPEED_UNKNOWN;
+
+	net2272_cancel_dma(dev);
+
+	net2272_write(dev, IRQENB0, 0);
+	net2272_write(dev, IRQENB1, 0);
+
+	/* clear irq state */
+	net2272_write(dev, IRQSTAT0, 0xff);
+	net2272_write(dev, IRQSTAT1, ~(1 << SUSPEND_REQUEST_INTERRUPT));
+
+	net2272_write(dev, DMAREQ,
+		(0 << DMA_BUFFER_VALID) |
+		(0 << DMA_REQUEST_ENABLE) |
+		(1 << DMA_CONTROL_DACK) |
+		(dev->dma_eot_polarity << EOT_POLARITY) |
+		(dev->dma_dack_polarity << DACK_POLARITY) |
+		(dev->dma_dreq_polarity << DREQ_POLARITY) |
+		((dma_ep >> 1) << DMA_ENDPOINT_SELECT));
+
+	net2272_cancel_dma(dev);
+	net2272_set_fifo_mode(dev, (fifo_mode <= 3) ? fifo_mode : 0);
+
+	/* Set the NET2272 ep fifo data width to 16-bit mode and for correct byte swapping
+	 * note that the higher level gadget drivers are expected to convert data to little endian.
+	 * Enable byte swap for your local bus/cpu if needed by setting BYTE_SWAP in LOCCTL here
+	 */
+	net2272_write(dev, LOCCTL, net2272_read(dev, LOCCTL) | (1 << DATA_WIDTH));
+	net2272_write(dev, LOCCTL1, (dma_mode << DMA_MODE));
+}
+
+static void
+net2272_usb_reinit(struct net2272 *dev)
+{
+	int i;
+
+	/* basic endpoint init */
+	for (i = 0; i < 4; ++i) {
+		struct net2272_ep *ep = &dev->ep[i];
+
+		ep->ep.name = ep_name[i];
+		ep->dev = dev;
+		ep->num = i;
+		ep->not_empty = 0;
+
+		if (use_dma && ep->num == dma_ep)
+			ep->dma = 1;
+
+		if (i > 0 && i <= 3)
+			ep->fifo_size = 512;
+		else
+			ep->fifo_size = 64;
+		net2272_ep_reset(ep);
+
+		if (i == 0) {
+			ep->ep.caps.type_control = true;
+		} else {
+			ep->ep.caps.type_iso = true;
+			ep->ep.caps.type_bulk = true;
+			ep->ep.caps.type_int = true;
+		}
+
+		ep->ep.caps.dir_in = true;
+		ep->ep.caps.dir_out = true;
+	}
+	usb_ep_set_maxpacket_limit(&dev->ep[0].ep, 64);
+
+	dev->gadget.ep0 = &dev->ep[0].ep;
+	dev->ep[0].stopped = 0;
+	INIT_LIST_HEAD(&dev->gadget.ep0->ep_list);
+}
+
+static void
+net2272_ep0_start(struct net2272 *dev)
+{
+	struct net2272_ep *ep0 = &dev->ep[0];
+
+	net2272_ep_write(ep0, EP_RSPSET,
+		(1 << NAK_OUT_PACKETS_MODE) |
+		(1 << ALT_NAK_OUT_PACKETS));
+	net2272_ep_write(ep0, EP_RSPCLR,
+		(1 << HIDE_STATUS_PHASE) |
+		(1 << CONTROL_STATUS_PHASE_HANDSHAKE));
+	net2272_write(dev, USBCTL0,
+		(dev->softconnect << USB_DETECT_ENABLE) |
+		(1 << USB_ROOT_PORT_WAKEUP_ENABLE) |
+		(1 << IO_WAKEUP_ENABLE));
+	net2272_write(dev, IRQENB0,
+		(1 << SETUP_PACKET_INTERRUPT_ENABLE) |
+		(1 << ENDPOINT_0_INTERRUPT_ENABLE) |
+		(1 << DMA_DONE_INTERRUPT_ENABLE));
+	net2272_write(dev, IRQENB1,
+		(1 << VBUS_INTERRUPT_ENABLE) |
+		(1 << ROOT_PORT_RESET_INTERRUPT_ENABLE) |
+		(1 << SUSPEND_REQUEST_CHANGE_INTERRUPT_ENABLE));
+}
+
+/* when a driver is successfully registered, it will receive
+ * control requests including set_configuration(), which enables
+ * non-control requests.  then usb traffic follows until a
+ * disconnect is reported.  then a host may connect again, or
+ * the driver might get unbound.
+ */
+static int net2272_start(struct usb_gadget *_gadget,
+		struct usb_gadget_driver *driver)
+{
+	struct net2272 *dev;
+	unsigned i;
+
+	if (!driver || !driver->setup ||
+	    driver->max_speed != USB_SPEED_HIGH)
+		return -EINVAL;
+
+	dev = container_of(_gadget, struct net2272, gadget);
+
+	for (i = 0; i < 4; ++i)
+		dev->ep[i].irqs = 0;
+	/* hook up the driver ... */
+	dev->softconnect = 1;
+	driver->driver.bus = NULL;
+	dev->driver = driver;
+
+	/* ... then enable host detection and ep0; and we're ready
+	 * for set_configuration as well as eventual disconnect.
+	 */
+	net2272_ep0_start(dev);
+
+	return 0;
+}
+
+static void
+stop_activity(struct net2272 *dev, struct usb_gadget_driver *driver)
+{
+	int i;
+
+	/* don't disconnect if it's not connected */
+	if (dev->gadget.speed == USB_SPEED_UNKNOWN)
+		driver = NULL;
+
+	/* stop hardware; prevent new request submissions;
+	 * and kill any outstanding requests.
+	 */
+	net2272_usb_reset(dev);
+	for (i = 0; i < 4; ++i)
+		net2272_dequeue_all(&dev->ep[i]);
+
+	/* report disconnect; the driver is already quiesced */
+	if (driver) {
+		spin_unlock(&dev->lock);
+		driver->disconnect(&dev->gadget);
+		spin_lock(&dev->lock);
+	}
+
+	net2272_usb_reinit(dev);
+}
+
+static int net2272_stop(struct usb_gadget *_gadget)
+{
+	struct net2272 *dev;
+	unsigned long flags;
+
+	dev = container_of(_gadget, struct net2272, gadget);
+
+	spin_lock_irqsave(&dev->lock, flags);
+	stop_activity(dev, NULL);
+	spin_unlock_irqrestore(&dev->lock, flags);
+
+	dev->driver = NULL;
+
+	return 0;
+}
+
+/*---------------------------------------------------------------------------*/
+/* handle ep-a/ep-b dma completions */
+static void
+net2272_handle_dma(struct net2272_ep *ep)
+{
+	struct net2272_request *req;
+	unsigned len;
+	int status;
+
+	if (!list_empty(&ep->queue))
+		req = list_entry(ep->queue.next,
+				struct net2272_request, queue);
+	else
+		req = NULL;
+
+	dev_vdbg(ep->dev->dev, "handle_dma %s req %p\n", ep->ep.name, req);
+
+	/* Ensure DREQ is de-asserted */
+	net2272_write(ep->dev, DMAREQ,
+		(0 << DMA_BUFFER_VALID)
+	      | (0 << DMA_REQUEST_ENABLE)
+	      | (1 << DMA_CONTROL_DACK)
+	      | (ep->dev->dma_eot_polarity << EOT_POLARITY)
+	      | (ep->dev->dma_dack_polarity << DACK_POLARITY)
+	      | (ep->dev->dma_dreq_polarity << DREQ_POLARITY)
+	      | (ep->dma << DMA_ENDPOINT_SELECT));
+
+	ep->dev->dma_busy = 0;
+
+	net2272_ep_write(ep, EP_IRQENB,
+		  (1 << DATA_PACKET_RECEIVED_INTERRUPT_ENABLE)
+		| (1 << DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE)
+		| net2272_ep_read(ep, EP_IRQENB));
+
+	/* device-to-host transfer completed */
+	if (ep->is_in) {
+		/* validate a short packet or zlp if necessary */
+		if ((req->req.length % ep->ep.maxpacket != 0) ||
+				req->req.zero)
+			set_fifo_bytecount(ep, 0);
+
+		net2272_done(ep, req, 0);
+		if (!list_empty(&ep->queue)) {
+			req = list_entry(ep->queue.next,
+					struct net2272_request, queue);
+			status = net2272_kick_dma(ep, req);
+			if (status < 0)
+				net2272_pio_advance(ep);
+		}
+
+	/* host-to-device transfer completed */
+	} else {
+		/* terminated with a short packet? */
+		if (net2272_read(ep->dev, IRQSTAT0) &
+				(1 << DMA_DONE_INTERRUPT)) {
+			/* abort system dma */
+			net2272_cancel_dma(ep->dev);
+		}
+
+		/* EP_TRANSFER will contain the number of bytes
+		 * actually received.
+		 * NOTE: There is no overflow detection on EP_TRANSFER:
+		 * We can't deal with transfers larger than 2^24 bytes!
+		 */
+		len = (net2272_ep_read(ep, EP_TRANSFER2) << 16)
+			| (net2272_ep_read(ep, EP_TRANSFER1) << 8)
+			| (net2272_ep_read(ep, EP_TRANSFER0));
+
+		if (ep->not_empty)
+			len += 4;
+
+		req->req.actual += len;
+
+		/* get any remaining data */
+		net2272_pio_advance(ep);
+	}
+}
+
+/*---------------------------------------------------------------------------*/
+
+static void
+net2272_handle_ep(struct net2272_ep *ep)
+{
+	struct net2272_request *req;
+	u8 stat0, stat1;
+
+	if (!list_empty(&ep->queue))
+		req = list_entry(ep->queue.next,
+			struct net2272_request, queue);
+	else
+		req = NULL;
+
+	/* ack all, and handle what we care about */
+	stat0 = net2272_ep_read(ep, EP_STAT0);
+	stat1 = net2272_ep_read(ep, EP_STAT1);
+	ep->irqs++;
+
+	dev_vdbg(ep->dev->dev, "%s ack ep_stat0 %02x, ep_stat1 %02x, req %p\n",
+		ep->ep.name, stat0, stat1, req ? &req->req : NULL);
+
+	net2272_ep_write(ep, EP_STAT0, stat0 &
+		~((1 << NAK_OUT_PACKETS)
+		| (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT)));
+	net2272_ep_write(ep, EP_STAT1, stat1);
+
+	/* data packet(s) received (in the fifo, OUT)
+	 * direction must be validated, otherwise control read status phase
+	 * could be interpreted as a valid packet
+	 */
+	if (!ep->is_in && (stat0 & (1 << DATA_PACKET_RECEIVED_INTERRUPT)))
+		net2272_pio_advance(ep);
+	/* data packet(s) transmitted (IN) */
+	else if (stat0 & (1 << DATA_PACKET_TRANSMITTED_INTERRUPT))
+		net2272_pio_advance(ep);
+}
+
+static struct net2272_ep *
+net2272_get_ep_by_addr(struct net2272 *dev, u16 wIndex)
+{
+	struct net2272_ep *ep;
+
+	if ((wIndex & USB_ENDPOINT_NUMBER_MASK) == 0)
+		return &dev->ep[0];
+
+	list_for_each_entry(ep, &dev->gadget.ep_list, ep.ep_list) {
+		u8 bEndpointAddress;
+
+		if (!ep->desc)
+			continue;
+		bEndpointAddress = ep->desc->bEndpointAddress;
+		if ((wIndex ^ bEndpointAddress) & USB_DIR_IN)
+			continue;
+		if ((wIndex & 0x0f) == (bEndpointAddress & 0x0f))
+			return ep;
+	}
+	return NULL;
+}
+
+/*
+ * USB Test Packet:
+ * JKJKJKJK * 9
+ * JJKKJJKK * 8
+ * JJJJKKKK * 8
+ * JJJJJJJKKKKKKK * 8
+ * JJJJJJJK * 8
+ * {JKKKKKKK * 10}, JK
+ */
+static const u8 net2272_test_packet[] = {
+	0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+	0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA, 0xAA,
+	0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE, 0xEE,
+	0xFE, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+	0x7F, 0xBF, 0xDF, 0xEF, 0xF7, 0xFB, 0xFD,
+	0xFC, 0x7E, 0xBF, 0xDF, 0xEF, 0xF7, 0xFD, 0x7E
+};
+
+static void
+net2272_set_test_mode(struct net2272 *dev, int mode)
+{
+	int i;
+
+	/* Disable all net2272 interrupts:
+	 * Nothing but a power cycle should stop the test.
+	 */
+	net2272_write(dev, IRQENB0, 0x00);
+	net2272_write(dev, IRQENB1, 0x00);
+
+	/* Force tranceiver to high-speed */
+	net2272_write(dev, XCVRDIAG, 1 << FORCE_HIGH_SPEED);
+
+	net2272_write(dev, PAGESEL, 0);
+	net2272_write(dev, EP_STAT0, 1 << DATA_PACKET_TRANSMITTED_INTERRUPT);
+	net2272_write(dev, EP_RSPCLR,
+			  (1 << CONTROL_STATUS_PHASE_HANDSHAKE)
+			| (1 << HIDE_STATUS_PHASE));
+	net2272_write(dev, EP_CFG, 1 << ENDPOINT_DIRECTION);
+	net2272_write(dev, EP_STAT1, 1 << BUFFER_FLUSH);
+
+	/* wait for status phase to complete */
+	while (!(net2272_read(dev, EP_STAT0) &
+				(1 << DATA_PACKET_TRANSMITTED_INTERRUPT)))
+		;
+
+	/* Enable test mode */
+	net2272_write(dev, USBTEST, mode);
+
+	/* load test packet */
+	if (mode == TEST_PACKET) {
+		/* switch to 8 bit mode */
+		net2272_write(dev, LOCCTL, net2272_read(dev, LOCCTL) &
+				~(1 << DATA_WIDTH));
+
+		for (i = 0; i < sizeof(net2272_test_packet); ++i)
+			net2272_write(dev, EP_DATA, net2272_test_packet[i]);
+
+		/* Validate test packet */
+		net2272_write(dev, EP_TRANSFER0, 0);
+	}
+}
+
+static void
+net2272_handle_stat0_irqs(struct net2272 *dev, u8 stat)
+{
+	struct net2272_ep *ep;
+	u8 num, scratch;
+
+	/* starting a control request? */
+	if (unlikely(stat & (1 << SETUP_PACKET_INTERRUPT))) {
+		union {
+			u8 raw[8];
+			struct usb_ctrlrequest	r;
+		} u;
+		int tmp = 0;
+		struct net2272_request *req;
+
+		if (dev->gadget.speed == USB_SPEED_UNKNOWN) {
+			if (net2272_read(dev, USBCTL1) & (1 << USB_HIGH_SPEED))
+				dev->gadget.speed = USB_SPEED_HIGH;
+			else
+				dev->gadget.speed = USB_SPEED_FULL;
+			dev_dbg(dev->dev, "%s\n",
+				usb_speed_string(dev->gadget.speed));
+		}
+
+		ep = &dev->ep[0];
+		ep->irqs++;
+
+		/* make sure any leftover interrupt state is cleared */
+		stat &= ~(1 << ENDPOINT_0_INTERRUPT);
+		while (!list_empty(&ep->queue)) {
+			req = list_entry(ep->queue.next,
+				struct net2272_request, queue);
+			net2272_done(ep, req,
+				(req->req.actual == req->req.length) ? 0 : -EPROTO);
+		}
+		ep->stopped = 0;
+		dev->protocol_stall = 0;
+		net2272_ep_write(ep, EP_STAT0,
+			    (1 << DATA_IN_TOKEN_INTERRUPT)
+			  | (1 << DATA_OUT_TOKEN_INTERRUPT)
+			  | (1 << DATA_PACKET_TRANSMITTED_INTERRUPT)
+			  | (1 << DATA_PACKET_RECEIVED_INTERRUPT)
+			  | (1 << SHORT_PACKET_TRANSFERRED_INTERRUPT));
+		net2272_ep_write(ep, EP_STAT1,
+			    (1 << TIMEOUT)
+			  | (1 << USB_OUT_ACK_SENT)
+			  | (1 << USB_OUT_NAK_SENT)
+			  | (1 << USB_IN_ACK_RCVD)
+			  | (1 << USB_IN_NAK_SENT)
+			  | (1 << USB_STALL_SENT)
+			  | (1 << LOCAL_OUT_ZLP));
+
+		/*
+		 * Ensure Control Read pre-validation setting is beyond maximum size
+		 *  - Control Writes can leave non-zero values in EP_TRANSFER. If
+		 *    an EP0 transfer following the Control Write is a Control Read,
+		 *    the NET2272 sees the non-zero EP_TRANSFER as an unexpected
+		 *    pre-validation count.
+		 *  - Setting EP_TRANSFER beyond the maximum EP0 transfer size ensures
+		 *    the pre-validation count cannot cause an unexpected validatation
+		 */
+		net2272_write(dev, PAGESEL, 0);
+		net2272_write(dev, EP_TRANSFER2, 0xff);
+		net2272_write(dev, EP_TRANSFER1, 0xff);
+		net2272_write(dev, EP_TRANSFER0, 0xff);
+
+		u.raw[0] = net2272_read(dev, SETUP0);
+		u.raw[1] = net2272_read(dev, SETUP1);
+		u.raw[2] = net2272_read(dev, SETUP2);
+		u.raw[3] = net2272_read(dev, SETUP3);
+		u.raw[4] = net2272_read(dev, SETUP4);
+		u.raw[5] = net2272_read(dev, SETUP5);
+		u.raw[6] = net2272_read(dev, SETUP6);
+		u.raw[7] = net2272_read(dev, SETUP7);
+		/*
+		 * If you have a big endian cpu make sure le16_to_cpus
+		 * performs the proper byte swapping here...
+		 */
+		le16_to_cpus(&u.r.wValue);
+		le16_to_cpus(&u.r.wIndex);
+		le16_to_cpus(&u.r.wLength);
+
+		/* ack the irq */
+		net2272_write(dev, IRQSTAT0, 1 << SETUP_PACKET_INTERRUPT);
+		stat ^= (1 << SETUP_PACKET_INTERRUPT);
+
+		/* watch control traffic at the token level, and force
+		 * synchronization before letting the status phase happen.
+		 */
+		ep->is_in = (u.r.bRequestType & USB_DIR_IN) != 0;
+		if (ep->is_in) {
+			scratch = (1 << DATA_PACKET_TRANSMITTED_INTERRUPT_ENABLE)
+				| (1 << DATA_OUT_TOKEN_INTERRUPT_ENABLE)
+				| (1 << DATA_IN_TOKEN_INTERRUPT_ENABLE);
+			stop_out_naking(ep);
+		} else
+			scratch = (1 << DATA_PACKET_RECEIVED_INTERRUPT_ENABLE)
+				| (1 << DATA_OUT_TOKEN_INTERRUPT_ENABLE)
+				| (1 << DATA_IN_TOKEN_INTERRUPT_ENABLE);
+		net2272_ep_write(ep, EP_IRQENB, scratch);
+
+		if ((u.r.bRequestType & USB_TYPE_MASK) != USB_TYPE_STANDARD)
+			goto delegate;
+		switch (u.r.bRequest) {
+		case USB_REQ_GET_STATUS: {
+			struct net2272_ep *e;
+			u16 status = 0;
+
+			switch (u.r.bRequestType & USB_RECIP_MASK) {
+			case USB_RECIP_ENDPOINT:
+				e = net2272_get_ep_by_addr(dev, u.r.wIndex);
+				if (!e || u.r.wLength > 2)
+					goto do_stall;
+				if (net2272_ep_read(e, EP_RSPSET) & (1 << ENDPOINT_HALT))
+					status = cpu_to_le16(1);
+				else
+					status = cpu_to_le16(0);
+
+				/* don't bother with a request object! */
+				net2272_ep_write(&dev->ep[0], EP_IRQENB, 0);
+				writew(status, net2272_reg_addr(dev, EP_DATA));
+				set_fifo_bytecount(&dev->ep[0], 0);
+				allow_status(ep);
+				dev_vdbg(dev->dev, "%s stat %02x\n",
+					ep->ep.name, status);
+				goto next_endpoints;
+			case USB_RECIP_DEVICE:
+				if (u.r.wLength > 2)
+					goto do_stall;
+				if (dev->gadget.is_selfpowered)
+					status = (1 << USB_DEVICE_SELF_POWERED);
+
+				/* don't bother with a request object! */
+				net2272_ep_write(&dev->ep[0], EP_IRQENB, 0);
+				writew(status, net2272_reg_addr(dev, EP_DATA));
+				set_fifo_bytecount(&dev->ep[0], 0);
+				allow_status(ep);
+				dev_vdbg(dev->dev, "device stat %02x\n", status);
+				goto next_endpoints;
+			case USB_RECIP_INTERFACE:
+				if (u.r.wLength > 2)
+					goto do_stall;
+
+				/* don't bother with a request object! */
+				net2272_ep_write(&dev->ep[0], EP_IRQENB, 0);
+				writew(status, net2272_reg_addr(dev, EP_DATA));
+				set_fifo_bytecount(&dev->ep[0], 0);
+				allow_status(ep);
+				dev_vdbg(dev->dev, "interface status %02x\n", status);
+				goto next_endpoints;
+			}
+
+			break;
+		}
+		case USB_REQ_CLEAR_FEATURE: {
+			struct net2272_ep *e;
+
+			if (u.r.bRequestType != USB_RECIP_ENDPOINT)
+				goto delegate;
+			if (u.r.wValue != USB_ENDPOINT_HALT ||
+			    u.r.wLength != 0)
+				goto do_stall;
+			e = net2272_get_ep_by_addr(dev, u.r.wIndex);
+			if (!e)
+				goto do_stall;
+			if (e->wedged) {
+				dev_vdbg(dev->dev, "%s wedged, halt not cleared\n",
+					ep->ep.name);
+			} else {
+				dev_vdbg(dev->dev, "%s clear halt\n", ep->ep.name);
+				clear_halt(e);
+			}
+			allow_status(ep);
+			goto next_endpoints;
+		}
+		case USB_REQ_SET_FEATURE: {
+			struct net2272_ep *e;
+
+			if (u.r.bRequestType == USB_RECIP_DEVICE) {
+				if (u.r.wIndex != NORMAL_OPERATION)
+					net2272_set_test_mode(dev, (u.r.wIndex >> 8));
+				allow_status(ep);
+				dev_vdbg(dev->dev, "test mode: %d\n", u.r.wIndex);
+				goto next_endpoints;
+			} else if (u.r.bRequestType != USB_RECIP_ENDPOINT)
+				goto delegate;
+			if (u.r.wValue != USB_ENDPOINT_HALT ||
+			    u.r.wLength != 0)
+				goto do_stall;
+			e = net2272_get_ep_by_addr(dev, u.r.wIndex);
+			if (!e)
+				goto do_stall;
+			set_halt(e);
+			allow_status(ep);
+			dev_vdbg(dev->dev, "%s set halt\n", ep->ep.name);
+			goto next_endpoints;
+		}
+		case USB_REQ_SET_ADDRESS: {
+			net2272_write(dev, OURADDR, u.r.wValue & 0xff);
+			allow_status(ep);
+			break;
+		}
+		default:
+ delegate:
+			dev_vdbg(dev->dev, "setup %02x.%02x v%04x i%04x "
+				"ep_cfg %08x\n",
+				u.r.bRequestType, u.r.bRequest,
+				u.r.wValue, u.r.wIndex,
+				net2272_ep_read(ep, EP_CFG));
+			spin_unlock(&dev->lock);
+			tmp = dev->driver->setup(&dev->gadget, &u.r);
+			spin_lock(&dev->lock);
+		}
+
+		/* stall ep0 on error */
+		if (tmp < 0) {
+ do_stall:
+			dev_vdbg(dev->dev, "req %02x.%02x protocol STALL; stat %d\n",
+				u.r.bRequestType, u.r.bRequest, tmp);
+			dev->protocol_stall = 1;
+		}
+	/* endpoint dma irq? */
+	} else if (stat & (1 << DMA_DONE_INTERRUPT)) {
+		net2272_cancel_dma(dev);
+		net2272_write(dev, IRQSTAT0, 1 << DMA_DONE_INTERRUPT);
+		stat &= ~(1 << DMA_DONE_INTERRUPT);
+		num = (net2272_read(dev, DMAREQ) & (1 << DMA_ENDPOINT_SELECT))
+			? 2 : 1;
+
+		ep = &dev->ep[num];
+		net2272_handle_dma(ep);
+	}
+
+ next_endpoints:
+	/* endpoint data irq? */
+	scratch = stat & 0x0f;
+	stat &= ~0x0f;
+	for (num = 0; scratch; num++) {
+		u8 t;
+
+		/* does this endpoint's FIFO and queue need tending? */
+		t = 1 << num;
+		if ((scratch & t) == 0)
+			continue;
+		scratch ^= t;
+
+		ep = &dev->ep[num];
+		net2272_handle_ep(ep);
+	}
+
+	/* some interrupts we can just ignore */
+	stat &= ~(1 << SOF_INTERRUPT);
+
+	if (stat)
+		dev_dbg(dev->dev, "unhandled irqstat0 %02x\n", stat);
+}
+
+static void
+net2272_handle_stat1_irqs(struct net2272 *dev, u8 stat)
+{
+	u8 tmp, mask;
+
+	/* after disconnect there's nothing else to do! */
+	tmp = (1 << VBUS_INTERRUPT) | (1 << ROOT_PORT_RESET_INTERRUPT);
+	mask = (1 << USB_HIGH_SPEED) | (1 << USB_FULL_SPEED);
+
+	if (stat & tmp) {
+		bool	reset = false;
+		bool	disconnect = false;
+
+		/*
+		 * Ignore disconnects and resets if the speed hasn't been set.
+		 * VBUS can bounce and there's always an initial reset.
+		 */
+		net2272_write(dev, IRQSTAT1, tmp);
+		if (dev->gadget.speed != USB_SPEED_UNKNOWN) {
+			if ((stat & (1 << VBUS_INTERRUPT)) &&
+					(net2272_read(dev, USBCTL1) &
+						(1 << VBUS_PIN)) == 0) {
+				disconnect = true;
+				dev_dbg(dev->dev, "disconnect %s\n",
+					dev->driver->driver.name);
+			} else if ((stat & (1 << ROOT_PORT_RESET_INTERRUPT)) &&
+					(net2272_read(dev, USBCTL1) & mask)
+						== 0) {
+				reset = true;
+				dev_dbg(dev->dev, "reset %s\n",
+					dev->driver->driver.name);
+			}
+
+			if (disconnect || reset) {
+				stop_activity(dev, dev->driver);
+				net2272_ep0_start(dev);
+				spin_unlock(&dev->lock);
+				if (reset)
+					usb_gadget_udc_reset
+						(&dev->gadget, dev->driver);
+				else
+					(dev->driver->disconnect)
+						(&dev->gadget);
+				spin_lock(&dev->lock);
+				return;
+			}
+		}
+		stat &= ~tmp;
+
+		if (!stat)
+			return;
+	}
+
+	tmp = (1 << SUSPEND_REQUEST_CHANGE_INTERRUPT);
+	if (stat & tmp) {
+		net2272_write(dev, IRQSTAT1, tmp);
+		if (stat & (1 << SUSPEND_REQUEST_INTERRUPT)) {
+			if (dev->driver->suspend)
+				dev->driver->suspend(&dev->gadget);
+			if (!enable_suspend) {
+				stat &= ~(1 << SUSPEND_REQUEST_INTERRUPT);
+				dev_dbg(dev->dev, "Suspend disabled, ignoring\n");
+			}
+		} else {
+			if (dev->driver->resume)
+				dev->driver->resume(&dev->gadget);
+		}
+		stat &= ~tmp;
+	}
+
+	/* clear any other status/irqs */
+	if (stat)
+		net2272_write(dev, IRQSTAT1, stat);
+
+	/* some status we can just ignore */
+	stat &= ~((1 << CONTROL_STATUS_INTERRUPT)
+			| (1 << SUSPEND_REQUEST_INTERRUPT)
+			| (1 << RESUME_INTERRUPT));
+	if (!stat)
+		return;
+	else
+		dev_dbg(dev->dev, "unhandled irqstat1 %02x\n", stat);
+}
+
+static irqreturn_t net2272_irq(int irq, void *_dev)
+{
+	struct net2272 *dev = _dev;
+#if defined(PLX_PCI_RDK) || defined(PLX_PCI_RDK2)
+	u32 intcsr;
+#endif
+#if defined(PLX_PCI_RDK)
+	u8 dmareq;
+#endif
+	spin_lock(&dev->lock);
+#if defined(PLX_PCI_RDK)
+	intcsr = readl(dev->rdk1.plx9054_base_addr + INTCSR);
+
+	if ((intcsr & LOCAL_INTERRUPT_TEST) == LOCAL_INTERRUPT_TEST) {
+		writel(intcsr & ~(1 << PCI_INTERRUPT_ENABLE),
+				dev->rdk1.plx9054_base_addr + INTCSR);
+		net2272_handle_stat1_irqs(dev, net2272_read(dev, IRQSTAT1));
+		net2272_handle_stat0_irqs(dev, net2272_read(dev, IRQSTAT0));
+		intcsr = readl(dev->rdk1.plx9054_base_addr + INTCSR);
+		writel(intcsr | (1 << PCI_INTERRUPT_ENABLE),
+			dev->rdk1.plx9054_base_addr + INTCSR);
+	}
+	if ((intcsr & DMA_CHANNEL_0_TEST) == DMA_CHANNEL_0_TEST) {
+		writeb((1 << CHANNEL_CLEAR_INTERRUPT | (0 << CHANNEL_ENABLE)),
+				dev->rdk1.plx9054_base_addr + DMACSR0);
+
+		dmareq = net2272_read(dev, DMAREQ);
+		if (dmareq & 0x01)
+			net2272_handle_dma(&dev->ep[2]);
+		else
+			net2272_handle_dma(&dev->ep[1]);
+	}
+#endif
+#if defined(PLX_PCI_RDK2)
+	/* see if PCI int for us by checking irqstat */
+	intcsr = readl(dev->rdk2.fpga_base_addr + RDK2_IRQSTAT);
+	if (!(intcsr & (1 << NET2272_PCI_IRQ))) {
+		spin_unlock(&dev->lock);
+		return IRQ_NONE;
+	}
+	/* check dma interrupts */
+#endif
+	/* Platform/devcice interrupt handler */
+#if !defined(PLX_PCI_RDK)
+	net2272_handle_stat1_irqs(dev, net2272_read(dev, IRQSTAT1));
+	net2272_handle_stat0_irqs(dev, net2272_read(dev, IRQSTAT0));
+#endif
+	spin_unlock(&dev->lock);
+
+	return IRQ_HANDLED;
+}
+
+static int net2272_present(struct net2272 *dev)
+{
+	/*
+	 * Quick test to see if CPU can communicate properly with the NET2272.
+	 * Verifies connection using writes and reads to write/read and
+	 * read-only registers.
+	 *
+	 * This routine is strongly recommended especially during early bring-up
+	 * of new hardware, however for designs that do not apply Power On System
+	 * Tests (POST) it may discarded (or perhaps minimized).
+	 */
+	unsigned int ii;
+	u8 val, refval;
+
+	/* Verify NET2272 write/read SCRATCH register can write and read */
+	refval = net2272_read(dev, SCRATCH);
+	for (ii = 0; ii < 0x100; ii += 7) {
+		net2272_write(dev, SCRATCH, ii);
+		val = net2272_read(dev, SCRATCH);
+		if (val != ii) {
+			dev_dbg(dev->dev,
+				"%s: write/read SCRATCH register test failed: "
+				"wrote:0x%2.2x, read:0x%2.2x\n",
+				__func__, ii, val);
+			return -EINVAL;
+		}
+	}
+	/* To be nice, we write the original SCRATCH value back: */
+	net2272_write(dev, SCRATCH, refval);
+
+	/* Verify NET2272 CHIPREV register is read-only: */
+	refval = net2272_read(dev, CHIPREV_2272);
+	for (ii = 0; ii < 0x100; ii += 7) {
+		net2272_write(dev, CHIPREV_2272, ii);
+		val = net2272_read(dev, CHIPREV_2272);
+		if (val != refval) {
+			dev_dbg(dev->dev,
+				"%s: write/read CHIPREV register test failed: "
+				"wrote 0x%2.2x, read:0x%2.2x expected:0x%2.2x\n",
+				__func__, ii, val, refval);
+			return -EINVAL;
+		}
+	}
+
+	/*
+	 * Verify NET2272's "NET2270 legacy revision" register
+	 *  - NET2272 has two revision registers. The NET2270 legacy revision
+	 *    register should read the same value, regardless of the NET2272
+	 *    silicon revision.  The legacy register applies to NET2270
+	 *    firmware being applied to the NET2272.
+	 */
+	val = net2272_read(dev, CHIPREV_LEGACY);
+	if (val != NET2270_LEGACY_REV) {
+		/*
+		 * Unexpected legacy revision value
+		 * - Perhaps the chip is a NET2270?
+		 */
+		dev_dbg(dev->dev,
+			"%s: WARNING: UNEXPECTED NET2272 LEGACY REGISTER VALUE:\n"
+			" - CHIPREV_LEGACY: expected 0x%2.2x, got:0x%2.2x. (Not NET2272?)\n",
+			__func__, NET2270_LEGACY_REV, val);
+		return -EINVAL;
+	}
+
+	/*
+	 * Verify NET2272 silicon revision
+	 *  - This revision register is appropriate for the silicon version
+	 *    of the NET2272
+	 */
+	val = net2272_read(dev, CHIPREV_2272);
+	switch (val) {
+	case CHIPREV_NET2272_R1:
+		/*
+		 * NET2272 Rev 1 has DMA related errata:
+		 *  - Newer silicon (Rev 1A or better) required
+		 */
+		dev_dbg(dev->dev,
+			"%s: Rev 1 detected: newer silicon recommended for DMA support\n",
+			__func__);
+		break;
+	case CHIPREV_NET2272_R1A:
+		break;
+	default:
+		/* NET2272 silicon version *may* not work with this firmware */
+		dev_dbg(dev->dev,
+			"%s: unexpected silicon revision register value: "
+			" CHIPREV_2272: 0x%2.2x\n",
+			__func__, val);
+		/*
+		 * Return Success, even though the chip rev is not an expected value
+		 *  - Older, pre-built firmware can attempt to operate on newer silicon
+		 *  - Often, new silicon is perfectly compatible
+		 */
+	}
+
+	/* Success: NET2272 checks out OK */
+	return 0;
+}
+
+static void
+net2272_gadget_release(struct device *_dev)
+{
+	struct net2272 *dev = dev_get_drvdata(_dev);
+	kfree(dev);
+}
+
+/*---------------------------------------------------------------------------*/
+
+static void
+net2272_remove(struct net2272 *dev)
+{
+	usb_del_gadget_udc(&dev->gadget);
+	free_irq(dev->irq, dev);
+	iounmap(dev->base_addr);
+	device_remove_file(dev->dev, &dev_attr_registers);
+
+	dev_info(dev->dev, "unbind\n");
+}
+
+static struct net2272 *net2272_probe_init(struct device *dev, unsigned int irq)
+{
+	struct net2272 *ret;
+
+	if (!irq) {
+		dev_dbg(dev, "No IRQ!\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	/* alloc, and start init */
+	ret = kzalloc(sizeof(*ret), GFP_KERNEL);
+	if (!ret)
+		return ERR_PTR(-ENOMEM);
+
+	spin_lock_init(&ret->lock);
+	ret->irq = irq;
+	ret->dev = dev;
+	ret->gadget.ops = &net2272_ops;
+	ret->gadget.max_speed = USB_SPEED_HIGH;
+
+	/* the "gadget" abstracts/virtualizes the controller */
+	ret->gadget.name = driver_name;
+
+	return ret;
+}
+
+static int
+net2272_probe_fin(struct net2272 *dev, unsigned int irqflags)
+{
+	int ret;
+
+	/* See if there... */
+	if (net2272_present(dev)) {
+		dev_warn(dev->dev, "2272 not found!\n");
+		ret = -ENODEV;
+		goto err;
+	}
+
+	net2272_usb_reset(dev);
+	net2272_usb_reinit(dev);
+
+	ret = request_irq(dev->irq, net2272_irq, irqflags, driver_name, dev);
+	if (ret) {
+		dev_err(dev->dev, "request interrupt %i failed\n", dev->irq);
+		goto err;
+	}
+
+	dev->chiprev = net2272_read(dev, CHIPREV_2272);
+
+	/* done */
+	dev_info(dev->dev, "%s\n", driver_desc);
+	dev_info(dev->dev, "irq %i, mem %p, chip rev %04x, dma %s\n",
+		dev->irq, dev->base_addr, dev->chiprev,
+		dma_mode_string());
+	dev_info(dev->dev, "version: %s\n", driver_vers);
+
+	ret = device_create_file(dev->dev, &dev_attr_registers);
+	if (ret)
+		goto err_irq;
+
+	ret = usb_add_gadget_udc_release(dev->dev, &dev->gadget,
+			net2272_gadget_release);
+	if (ret)
+		goto err_add_udc;
+
+	return 0;
+
+err_add_udc:
+	device_remove_file(dev->dev, &dev_attr_registers);
+ err_irq:
+	free_irq(dev->irq, dev);
+ err:
+	return ret;
+}
+
+#ifdef CONFIG_USB_PCI
+
+/*
+ * wrap this driver around the specified device, but
+ * don't respond over USB until a gadget driver binds to us
+ */
+
+static int
+net2272_rdk1_probe(struct pci_dev *pdev, struct net2272 *dev)
+{
+	unsigned long resource, len, tmp;
+	void __iomem *mem_mapped_addr[4];
+	int ret, i;
+
+	/*
+	 * BAR 0 holds PLX 9054 config registers
+	 * BAR 1 is i/o memory; unused here
+	 * BAR 2 holds EPLD config registers
+	 * BAR 3 holds NET2272 registers
+	 */
+
+	/* Find and map all address spaces */
+	for (i = 0; i < 4; ++i) {
+		if (i == 1)
+			continue;	/* BAR1 unused */
+
+		resource = pci_resource_start(pdev, i);
+		len = pci_resource_len(pdev, i);
+
+		if (!request_mem_region(resource, len, driver_name)) {
+			dev_dbg(dev->dev, "controller already in use\n");
+			ret = -EBUSY;
+			goto err;
+		}
+
+		mem_mapped_addr[i] = ioremap_nocache(resource, len);
+		if (mem_mapped_addr[i] == NULL) {
+			release_mem_region(resource, len);
+			dev_dbg(dev->dev, "can't map memory\n");
+			ret = -EFAULT;
+			goto err;
+		}
+	}
+
+	dev->rdk1.plx9054_base_addr = mem_mapped_addr[0];
+	dev->rdk1.epld_base_addr = mem_mapped_addr[2];
+	dev->base_addr = mem_mapped_addr[3];
+
+	/* Set PLX 9054 bus width (16 bits) */
+	tmp = readl(dev->rdk1.plx9054_base_addr + LBRD1);
+	writel((tmp & ~(3 << MEMORY_SPACE_LOCAL_BUS_WIDTH)) | W16_BIT,
+			dev->rdk1.plx9054_base_addr + LBRD1);
+
+	/* Enable PLX 9054 Interrupts */
+	writel(readl(dev->rdk1.plx9054_base_addr + INTCSR) |
+			(1 << PCI_INTERRUPT_ENABLE) |
+			(1 << LOCAL_INTERRUPT_INPUT_ENABLE),
+			dev->rdk1.plx9054_base_addr + INTCSR);
+
+	writeb((1 << CHANNEL_CLEAR_INTERRUPT | (0 << CHANNEL_ENABLE)),
+			dev->rdk1.plx9054_base_addr + DMACSR0);
+
+	/* reset */
+	writeb((1 << EPLD_DMA_ENABLE) |
+		(1 << DMA_CTL_DACK) |
+		(1 << DMA_TIMEOUT_ENABLE) |
+		(1 << USER) |
+		(0 << MPX_MODE) |
+		(1 << BUSWIDTH) |
+		(1 << NET2272_RESET),
+		dev->base_addr + EPLD_IO_CONTROL_REGISTER);
+
+	mb();
+	writeb(readb(dev->base_addr + EPLD_IO_CONTROL_REGISTER) &
+		~(1 << NET2272_RESET),
+		dev->base_addr + EPLD_IO_CONTROL_REGISTER);
+	udelay(200);
+
+	return 0;
+
+ err:
+	while (--i >= 0) {
+		iounmap(mem_mapped_addr[i]);
+		release_mem_region(pci_resource_start(pdev, i),
+			pci_resource_len(pdev, i));
+	}
+
+	return ret;
+}
+
+static int
+net2272_rdk2_probe(struct pci_dev *pdev, struct net2272 *dev)
+{
+	unsigned long resource, len;
+	void __iomem *mem_mapped_addr[2];
+	int ret, i;
+
+	/*
+	 * BAR 0 holds FGPA config registers
+	 * BAR 1 holds NET2272 registers
+	 */
+
+	/* Find and map all address spaces, bar2-3 unused in rdk 2 */
+	for (i = 0; i < 2; ++i) {
+		resource = pci_resource_start(pdev, i);
+		len = pci_resource_len(pdev, i);
+
+		if (!request_mem_region(resource, len, driver_name)) {
+			dev_dbg(dev->dev, "controller already in use\n");
+			ret = -EBUSY;
+			goto err;
+		}
+
+		mem_mapped_addr[i] = ioremap_nocache(resource, len);
+		if (mem_mapped_addr[i] == NULL) {
+			release_mem_region(resource, len);
+			dev_dbg(dev->dev, "can't map memory\n");
+			ret = -EFAULT;
+			goto err;
+		}
+	}
+
+	dev->rdk2.fpga_base_addr = mem_mapped_addr[0];
+	dev->base_addr = mem_mapped_addr[1];
+
+	mb();
+	/* Set 2272 bus width (16 bits) and reset */
+	writel((1 << CHIP_RESET), dev->rdk2.fpga_base_addr + RDK2_LOCCTLRDK);
+	udelay(200);
+	writel((1 << BUS_WIDTH), dev->rdk2.fpga_base_addr + RDK2_LOCCTLRDK);
+	/* Print fpga version number */
+	dev_info(dev->dev, "RDK2 FPGA version %08x\n",
+		readl(dev->rdk2.fpga_base_addr + RDK2_FPGAREV));
+	/* Enable FPGA Interrupts */
+	writel((1 << NET2272_PCI_IRQ), dev->rdk2.fpga_base_addr + RDK2_IRQENB);
+
+	return 0;
+
+ err:
+	while (--i >= 0) {
+		iounmap(mem_mapped_addr[i]);
+		release_mem_region(pci_resource_start(pdev, i),
+			pci_resource_len(pdev, i));
+	}
+
+	return ret;
+}
+
+static int
+net2272_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct net2272 *dev;
+	int ret;
+
+	dev = net2272_probe_init(&pdev->dev, pdev->irq);
+	if (IS_ERR(dev))
+		return PTR_ERR(dev);
+	dev->dev_id = pdev->device;
+
+	if (pci_enable_device(pdev) < 0) {
+		ret = -ENODEV;
+		goto err_free;
+	}
+
+	pci_set_master(pdev);
+
+	switch (pdev->device) {
+	case PCI_DEVICE_ID_RDK1: ret = net2272_rdk1_probe(pdev, dev); break;
+	case PCI_DEVICE_ID_RDK2: ret = net2272_rdk2_probe(pdev, dev); break;
+	default: BUG();
+	}
+	if (ret)
+		goto err_pci;
+
+	ret = net2272_probe_fin(dev, 0);
+	if (ret)
+		goto err_pci;
+
+	pci_set_drvdata(pdev, dev);
+
+	return 0;
+
+ err_pci:
+	pci_disable_device(pdev);
+ err_free:
+	kfree(dev);
+
+	return ret;
+}
+
+static void
+net2272_rdk1_remove(struct pci_dev *pdev, struct net2272 *dev)
+{
+	int i;
+
+	/* disable PLX 9054 interrupts */
+	writel(readl(dev->rdk1.plx9054_base_addr + INTCSR) &
+		~(1 << PCI_INTERRUPT_ENABLE),
+		dev->rdk1.plx9054_base_addr + INTCSR);
+
+	/* clean up resources allocated during probe() */
+	iounmap(dev->rdk1.plx9054_base_addr);
+	iounmap(dev->rdk1.epld_base_addr);
+
+	for (i = 0; i < 4; ++i) {
+		if (i == 1)
+			continue;	/* BAR1 unused */
+		release_mem_region(pci_resource_start(pdev, i),
+			pci_resource_len(pdev, i));
+	}
+}
+
+static void
+net2272_rdk2_remove(struct pci_dev *pdev, struct net2272 *dev)
+{
+	int i;
+
+	/* disable fpga interrupts
+	writel(readl(dev->rdk1.plx9054_base_addr + INTCSR) &
+			~(1 << PCI_INTERRUPT_ENABLE),
+			dev->rdk1.plx9054_base_addr + INTCSR);
+	*/
+
+	/* clean up resources allocated during probe() */
+	iounmap(dev->rdk2.fpga_base_addr);
+
+	for (i = 0; i < 2; ++i)
+		release_mem_region(pci_resource_start(pdev, i),
+			pci_resource_len(pdev, i));
+}
+
+static void
+net2272_pci_remove(struct pci_dev *pdev)
+{
+	struct net2272 *dev = pci_get_drvdata(pdev);
+
+	net2272_remove(dev);
+
+	switch (pdev->device) {
+	case PCI_DEVICE_ID_RDK1: net2272_rdk1_remove(pdev, dev); break;
+	case PCI_DEVICE_ID_RDK2: net2272_rdk2_remove(pdev, dev); break;
+	default: BUG();
+	}
+
+	pci_disable_device(pdev);
+
+	kfree(dev);
+}
+
+/* Table of matching PCI IDs */
+static struct pci_device_id pci_ids[] = {
+	{	/* RDK 1 card */
+		.class       = ((PCI_CLASS_BRIDGE_OTHER << 8) | 0xfe),
+		.class_mask  = 0,
+		.vendor      = PCI_VENDOR_ID_PLX,
+		.device      = PCI_DEVICE_ID_RDK1,
+		.subvendor   = PCI_ANY_ID,
+		.subdevice   = PCI_ANY_ID,
+	},
+	{	/* RDK 2 card */
+		.class       = ((PCI_CLASS_BRIDGE_OTHER << 8) | 0xfe),
+		.class_mask  = 0,
+		.vendor      = PCI_VENDOR_ID_PLX,
+		.device      = PCI_DEVICE_ID_RDK2,
+		.subvendor   = PCI_ANY_ID,
+		.subdevice   = PCI_ANY_ID,
+	},
+	{ }
+};
+MODULE_DEVICE_TABLE(pci, pci_ids);
+
+static struct pci_driver net2272_pci_driver = {
+	.name     = driver_name,
+	.id_table = pci_ids,
+
+	.probe    = net2272_pci_probe,
+	.remove   = net2272_pci_remove,
+};
+
+static int net2272_pci_register(void)
+{
+	return pci_register_driver(&net2272_pci_driver);
+}
+
+static void net2272_pci_unregister(void)
+{
+	pci_unregister_driver(&net2272_pci_driver);
+}
+
+#else
+static inline int net2272_pci_register(void) { return 0; }
+static inline void net2272_pci_unregister(void) { }
+#endif
+
+/*---------------------------------------------------------------------------*/
+
+static int
+net2272_plat_probe(struct platform_device *pdev)
+{
+	struct net2272 *dev;
+	int ret;
+	unsigned int irqflags;
+	resource_size_t base, len;
+	struct resource *iomem, *iomem_bus, *irq_res;
+
+	irq_res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
+	iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	iomem_bus = platform_get_resource(pdev, IORESOURCE_BUS, 0);
+	if (!irq_res || !iomem) {
+		dev_err(&pdev->dev, "must provide irq/base addr");
+		return -EINVAL;
+	}
+
+	dev = net2272_probe_init(&pdev->dev, irq_res->start);
+	if (IS_ERR(dev))
+		return PTR_ERR(dev);
+
+	irqflags = 0;
+	if (irq_res->flags & IORESOURCE_IRQ_HIGHEDGE)
+		irqflags |= IRQF_TRIGGER_RISING;
+	if (irq_res->flags & IORESOURCE_IRQ_LOWEDGE)
+		irqflags |= IRQF_TRIGGER_FALLING;
+	if (irq_res->flags & IORESOURCE_IRQ_HIGHLEVEL)
+		irqflags |= IRQF_TRIGGER_HIGH;
+	if (irq_res->flags & IORESOURCE_IRQ_LOWLEVEL)
+		irqflags |= IRQF_TRIGGER_LOW;
+
+	base = iomem->start;
+	len = resource_size(iomem);
+	if (iomem_bus)
+		dev->base_shift = iomem_bus->start;
+
+	if (!request_mem_region(base, len, driver_name)) {
+		dev_dbg(dev->dev, "get request memory region!\n");
+		ret = -EBUSY;
+		goto err;
+	}
+	dev->base_addr = ioremap_nocache(base, len);
+	if (!dev->base_addr) {
+		dev_dbg(dev->dev, "can't map memory\n");
+		ret = -EFAULT;
+		goto err_req;
+	}
+
+	ret = net2272_probe_fin(dev, IRQF_TRIGGER_LOW);
+	if (ret)
+		goto err_io;
+
+	platform_set_drvdata(pdev, dev);
+	dev_info(&pdev->dev, "running in 16-bit, %sbyte swap local bus mode\n",
+		(net2272_read(dev, LOCCTL) & (1 << BYTE_SWAP)) ? "" : "no ");
+
+	return 0;
+
+ err_io:
+	iounmap(dev->base_addr);
+ err_req:
+	release_mem_region(base, len);
+ err:
+	kfree(dev);
+
+	return ret;
+}
+
+static int
+net2272_plat_remove(struct platform_device *pdev)
+{
+	struct net2272 *dev = platform_get_drvdata(pdev);
+
+	net2272_remove(dev);
+
+	release_mem_region(pdev->resource[0].start,
+		resource_size(&pdev->resource[0]));
+
+	kfree(dev);
+
+	return 0;
+}
+
+static struct platform_driver net2272_plat_driver = {
+	.probe   = net2272_plat_probe,
+	.remove  = net2272_plat_remove,
+	.driver  = {
+		.name  = driver_name,
+	},
+	/* FIXME .suspend, .resume */
+};
+MODULE_ALIAS("platform:net2272");
+
+static int __init net2272_init(void)
+{
+	int ret;
+
+	ret = net2272_pci_register();
+	if (ret)
+		return ret;
+	ret = platform_driver_register(&net2272_plat_driver);
+	if (ret)
+		goto err_pci;
+	return ret;
+
+err_pci:
+	net2272_pci_unregister();
+	return ret;
+}
+module_init(net2272_init);
+
+static void __exit net2272_cleanup(void)
+{
+	net2272_pci_unregister();
+	platform_driver_unregister(&net2272_plat_driver);
+}
+module_exit(net2272_cleanup);
+
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_AUTHOR("PLX Technology, Inc.");
+MODULE_LICENSE("GPL");