Adding upstream version 4.19.249.upstream/4.19.249

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 448 insertions, 0 deletions

diff --git a/drivers/usb/host/oxu210hp.h b/drivers/usb/host/oxu210hp.h
new file mode 100644
index 000000000..437044147
--- /dev/null
+++ b/drivers/usb/host/oxu210hp.h
@@ -0,0 +1,448 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Host interface registers
+ */
+
+#define OXU_DEVICEID			0x00
+	#define OXU_REV_MASK		0xffff0000
+	#define OXU_REV_SHIFT		16
+	#define OXU_REV_2100		0x2100
+	#define OXU_BO_SHIFT		8
+	#define OXU_BO_MASK		(0x3 << OXU_BO_SHIFT)
+	#define OXU_MAJ_REV_SHIFT	4
+	#define OXU_MAJ_REV_MASK	(0xf << OXU_MAJ_REV_SHIFT)
+	#define OXU_MIN_REV_SHIFT	0
+	#define OXU_MIN_REV_MASK	(0xf << OXU_MIN_REV_SHIFT)
+#define OXU_HOSTIFCONFIG		0x04
+#define OXU_SOFTRESET			0x08
+	#define OXU_SRESET		(1 << 0)
+
+#define OXU_PIOBURSTREADCTRL		0x0C
+
+#define OXU_CHIPIRQSTATUS		0x10
+#define OXU_CHIPIRQEN_SET		0x14
+#define OXU_CHIPIRQEN_CLR		0x18
+	#define OXU_USBSPHLPWUI		0x00000080
+	#define OXU_USBOTGLPWUI		0x00000040
+	#define OXU_USBSPHI		0x00000002
+	#define OXU_USBOTGI		0x00000001
+
+#define OXU_CLKCTRL_SET			0x1C
+	#define OXU_SYSCLKEN		0x00000008
+	#define OXU_USBSPHCLKEN		0x00000002
+	#define OXU_USBOTGCLKEN		0x00000001
+
+#define OXU_ASO				0x68
+	#define OXU_SPHPOEN		0x00000100
+	#define OXU_OVRCCURPUPDEN	0x00000800
+	#define OXU_ASO_OP		(1 << 10)
+	#define OXU_COMPARATOR		0x000004000
+
+#define OXU_USBMODE			0x1A8
+	#define OXU_VBPS		0x00000020
+	#define OXU_ES_LITTLE		0x00000000
+	#define OXU_CM_HOST_ONLY	0x00000003
+
+/*
+ * Proper EHCI structs & defines
+ */
+
+/* Magic numbers that can affect system performance */
+#define EHCI_TUNE_CERR		3	/* 0-3 qtd retries; 0 == don't stop */
+#define EHCI_TUNE_RL_HS		4	/* nak throttle; see 4.9 */
+#define EHCI_TUNE_RL_TT		0
+#define EHCI_TUNE_MULT_HS	1	/* 1-3 transactions/uframe; 4.10.3 */
+#define EHCI_TUNE_MULT_TT	1
+#define EHCI_TUNE_FLS		2	/* (small) 256 frame schedule */
+
+struct oxu_hcd;
+
+/* EHCI register interface, corresponds to EHCI Revision 0.95 specification */
+
+/* Section 2.2 Host Controller Capability Registers */
+struct ehci_caps {
+	/* these fields are specified as 8 and 16 bit registers,
+	 * but some hosts can't perform 8 or 16 bit PCI accesses.
+	 */
+	u32		hc_capbase;
+#define HC_LENGTH(p)		(((p)>>00)&0x00ff)	/* bits 7:0 */
+#define HC_VERSION(p)		(((p)>>16)&0xffff)	/* bits 31:16 */
+	u32		hcs_params;     /* HCSPARAMS - offset 0x4 */
+#define HCS_DEBUG_PORT(p)	(((p)>>20)&0xf)	/* bits 23:20, debug port? */
+#define HCS_INDICATOR(p)	((p)&(1 << 16))	/* true: has port indicators */
+#define HCS_N_CC(p)		(((p)>>12)&0xf)	/* bits 15:12, #companion HCs */
+#define HCS_N_PCC(p)		(((p)>>8)&0xf)	/* bits 11:8, ports per CC */
+#define HCS_PORTROUTED(p)	((p)&(1 << 7))	/* true: port routing */
+#define HCS_PPC(p)		((p)&(1 << 4))	/* true: port power control */
+#define HCS_N_PORTS(p)		(((p)>>0)&0xf)	/* bits 3:0, ports on HC */
+
+	u32		hcc_params;      /* HCCPARAMS - offset 0x8 */
+#define HCC_EXT_CAPS(p)		(((p)>>8)&0xff)	/* for pci extended caps */
+#define HCC_ISOC_CACHE(p)       ((p)&(1 << 7))  /* true: can cache isoc frame */
+#define HCC_ISOC_THRES(p)       (((p)>>4)&0x7)  /* bits 6:4, uframes cached */
+#define HCC_CANPARK(p)		((p)&(1 << 2))  /* true: can park on async qh */
+#define HCC_PGM_FRAMELISTLEN(p) ((p)&(1 << 1))  /* true: periodic_size changes*/
+#define HCC_64BIT_ADDR(p)       ((p)&(1))       /* true: can use 64-bit addr */
+	u8		portroute[8];	 /* nibbles for routing - offset 0xC */
+} __attribute__ ((packed));
+
+
+/* Section 2.3 Host Controller Operational Registers */
+struct ehci_regs {
+	/* USBCMD: offset 0x00 */
+	u32		command;
+/* 23:16 is r/w intr rate, in microframes; default "8" == 1/msec */
+#define CMD_PARK	(1<<11)		/* enable "park" on async qh */
+#define CMD_PARK_CNT(c)	(((c)>>8)&3)	/* how many transfers to park for */
+#define CMD_LRESET	(1<<7)		/* partial reset (no ports, etc) */
+#define CMD_IAAD	(1<<6)		/* "doorbell" interrupt async advance */
+#define CMD_ASE		(1<<5)		/* async schedule enable */
+#define CMD_PSE		(1<<4)		/* periodic schedule enable */
+/* 3:2 is periodic frame list size */
+#define CMD_RESET	(1<<1)		/* reset HC not bus */
+#define CMD_RUN		(1<<0)		/* start/stop HC */
+
+	/* USBSTS: offset 0x04 */
+	u32		status;
+#define STS_ASS		(1<<15)		/* Async Schedule Status */
+#define STS_PSS		(1<<14)		/* Periodic Schedule Status */
+#define STS_RECL	(1<<13)		/* Reclamation */
+#define STS_HALT	(1<<12)		/* Not running (any reason) */
+/* some bits reserved */
+	/* these STS_* flags are also intr_enable bits (USBINTR) */
+#define STS_IAA		(1<<5)		/* Interrupted on async advance */
+#define STS_FATAL	(1<<4)		/* such as some PCI access errors */
+#define STS_FLR		(1<<3)		/* frame list rolled over */
+#define STS_PCD		(1<<2)		/* port change detect */
+#define STS_ERR		(1<<1)		/* "error" completion (overflow, ...) */
+#define STS_INT		(1<<0)		/* "normal" completion (short, ...) */
+
+#define INTR_MASK (STS_IAA | STS_FATAL | STS_PCD | STS_ERR | STS_INT)
+
+	/* USBINTR: offset 0x08 */
+	u32		intr_enable;
+
+	/* FRINDEX: offset 0x0C */
+	u32		frame_index;	/* current microframe number */
+	/* CTRLDSSEGMENT: offset 0x10 */
+	u32		segment;	/* address bits 63:32 if needed */
+	/* PERIODICLISTBASE: offset 0x14 */
+	u32		frame_list;	/* points to periodic list */
+	/* ASYNCLISTADDR: offset 0x18 */
+	u32		async_next;	/* address of next async queue head */
+
+	u32		reserved[9];
+
+	/* CONFIGFLAG: offset 0x40 */
+	u32		configured_flag;
+#define FLAG_CF		(1<<0)		/* true: we'll support "high speed" */
+
+	/* PORTSC: offset 0x44 */
+	u32		port_status[0];	/* up to N_PORTS */
+/* 31:23 reserved */
+#define PORT_WKOC_E	(1<<22)		/* wake on overcurrent (enable) */
+#define PORT_WKDISC_E	(1<<21)		/* wake on disconnect (enable) */
+#define PORT_WKCONN_E	(1<<20)		/* wake on connect (enable) */
+/* 19:16 for port testing */
+#define PORT_LED_OFF	(0<<14)
+#define PORT_LED_AMBER	(1<<14)
+#define PORT_LED_GREEN	(2<<14)
+#define PORT_LED_MASK	(3<<14)
+#define PORT_OWNER	(1<<13)		/* true: companion hc owns this port */
+#define PORT_POWER	(1<<12)		/* true: has power (see PPC) */
+#define PORT_USB11(x) (((x)&(3<<10)) == (1<<10))	/* USB 1.1 device */
+/* 11:10 for detecting lowspeed devices (reset vs release ownership) */
+/* 9 reserved */
+#define PORT_RESET	(1<<8)		/* reset port */
+#define PORT_SUSPEND	(1<<7)		/* suspend port */
+#define PORT_RESUME	(1<<6)		/* resume it */
+#define PORT_OCC	(1<<5)		/* over current change */
+#define PORT_OC		(1<<4)		/* over current active */
+#define PORT_PEC	(1<<3)		/* port enable change */
+#define PORT_PE		(1<<2)		/* port enable */
+#define PORT_CSC	(1<<1)		/* connect status change */
+#define PORT_CONNECT	(1<<0)		/* device connected */
+#define PORT_RWC_BITS   (PORT_CSC | PORT_PEC | PORT_OCC)
+} __attribute__ ((packed));
+
+/* Appendix C, Debug port ... intended for use with special "debug devices"
+ * that can help if there's no serial console.  (nonstandard enumeration.)
+ */
+struct ehci_dbg_port {
+	u32	control;
+#define DBGP_OWNER	(1<<30)
+#define DBGP_ENABLED	(1<<28)
+#define DBGP_DONE	(1<<16)
+#define DBGP_INUSE	(1<<10)
+#define DBGP_ERRCODE(x)	(((x)>>7)&0x07)
+#	define DBGP_ERR_BAD	1
+#	define DBGP_ERR_SIGNAL	2
+#define DBGP_ERROR	(1<<6)
+#define DBGP_GO		(1<<5)
+#define DBGP_OUT	(1<<4)
+#define DBGP_LEN(x)	(((x)>>0)&0x0f)
+	u32	pids;
+#define DBGP_PID_GET(x)		(((x)>>16)&0xff)
+#define DBGP_PID_SET(data, tok)	(((data)<<8)|(tok))
+	u32	data03;
+	u32	data47;
+	u32	address;
+#define DBGP_EPADDR(dev, ep)	(((dev)<<8)|(ep))
+} __attribute__ ((packed));
+
+
+#define	QTD_NEXT(dma)	cpu_to_le32((u32)dma)
+
+/*
+ * EHCI Specification 0.95 Section 3.5
+ * QTD: describe data transfer components (buffer, direction, ...)
+ * See Fig 3-6 "Queue Element Transfer Descriptor Block Diagram".
+ *
+ * These are associated only with "QH" (Queue Head) structures,
+ * used with control, bulk, and interrupt transfers.
+ */
+struct ehci_qtd {
+	/* first part defined by EHCI spec */
+	__le32			hw_next;		/* see EHCI 3.5.1 */
+	__le32			hw_alt_next;		/* see EHCI 3.5.2 */
+	__le32			hw_token;		/* see EHCI 3.5.3 */
+#define	QTD_TOGGLE	(1 << 31)	/* data toggle */
+#define	QTD_LENGTH(tok)	(((tok)>>16) & 0x7fff)
+#define	QTD_IOC		(1 << 15)	/* interrupt on complete */
+#define	QTD_CERR(tok)	(((tok)>>10) & 0x3)
+#define	QTD_PID(tok)	(((tok)>>8) & 0x3)
+#define	QTD_STS_ACTIVE	(1 << 7)	/* HC may execute this */
+#define	QTD_STS_HALT	(1 << 6)	/* halted on error */
+#define	QTD_STS_DBE	(1 << 5)	/* data buffer error (in HC) */
+#define	QTD_STS_BABBLE	(1 << 4)	/* device was babbling (qtd halted) */
+#define	QTD_STS_XACT	(1 << 3)	/* device gave illegal response */
+#define	QTD_STS_MMF	(1 << 2)	/* incomplete split transaction */
+#define	QTD_STS_STS	(1 << 1)	/* split transaction state */
+#define	QTD_STS_PING	(1 << 0)	/* issue PING? */
+	__le32			hw_buf[5];		/* see EHCI 3.5.4 */
+	__le32			hw_buf_hi[5];		/* Appendix B */
+
+	/* the rest is HCD-private */
+	dma_addr_t		qtd_dma;		/* qtd address */
+	struct list_head	qtd_list;		/* sw qtd list */
+	struct urb		*urb;			/* qtd's urb */
+	size_t			length;			/* length of buffer */
+
+	u32			qtd_buffer_len;
+	void			*buffer;
+	dma_addr_t		buffer_dma;
+	void			*transfer_buffer;
+	void			*transfer_dma;
+} __attribute__ ((aligned(32)));
+
+/* mask NakCnt+T in qh->hw_alt_next */
+#define QTD_MASK cpu_to_le32 (~0x1f)
+
+#define IS_SHORT_READ(token) (QTD_LENGTH(token) != 0 && QTD_PID(token) == 1)
+
+/* Type tag from {qh, itd, sitd, fstn}->hw_next */
+#define Q_NEXT_TYPE(dma) ((dma) & cpu_to_le32 (3 << 1))
+
+/* values for that type tag */
+#define Q_TYPE_QH	cpu_to_le32 (1 << 1)
+
+/* next async queue entry, or pointer to interrupt/periodic QH */
+#define	QH_NEXT(dma)	(cpu_to_le32(((u32)dma)&~0x01f)|Q_TYPE_QH)
+
+/* for periodic/async schedules and qtd lists, mark end of list */
+#define	EHCI_LIST_END	cpu_to_le32(1) /* "null pointer" to hw */
+
+/*
+ * Entries in periodic shadow table are pointers to one of four kinds
+ * of data structure.  That's dictated by the hardware; a type tag is
+ * encoded in the low bits of the hardware's periodic schedule.  Use
+ * Q_NEXT_TYPE to get the tag.
+ *
+ * For entries in the async schedule, the type tag always says "qh".
+ */
+union ehci_shadow {
+	struct ehci_qh		*qh;		/* Q_TYPE_QH */
+	__le32			*hw_next;	/* (all types) */
+	void			*ptr;
+};
+
+/*
+ * EHCI Specification 0.95 Section 3.6
+ * QH: describes control/bulk/interrupt endpoints
+ * See Fig 3-7 "Queue Head Structure Layout".
+ *
+ * These appear in both the async and (for interrupt) periodic schedules.
+ */
+
+struct ehci_qh {
+	/* first part defined by EHCI spec */
+	__le32			hw_next;	 /* see EHCI 3.6.1 */
+	__le32			hw_info1;	/* see EHCI 3.6.2 */
+#define	QH_HEAD		0x00008000
+	__le32			hw_info2;	/* see EHCI 3.6.2 */
+#define	QH_SMASK	0x000000ff
+#define	QH_CMASK	0x0000ff00
+#define	QH_HUBADDR	0x007f0000
+#define	QH_HUBPORT	0x3f800000
+#define	QH_MULT		0xc0000000
+	__le32			hw_current;	 /* qtd list - see EHCI 3.6.4 */
+
+	/* qtd overlay (hardware parts of a struct ehci_qtd) */
+	__le32			hw_qtd_next;
+	__le32			hw_alt_next;
+	__le32			hw_token;
+	__le32			hw_buf[5];
+	__le32			hw_buf_hi[5];
+
+	/* the rest is HCD-private */
+	dma_addr_t		qh_dma;		/* address of qh */
+	union ehci_shadow	qh_next;	/* ptr to qh; or periodic */
+	struct list_head	qtd_list;	/* sw qtd list */
+	struct ehci_qtd		*dummy;
+	struct ehci_qh		*reclaim;	/* next to reclaim */
+
+	struct oxu_hcd		*oxu;
+	struct kref		kref;
+	unsigned		stamp;
+
+	u8			qh_state;
+#define	QH_STATE_LINKED		1		/* HC sees this */
+#define	QH_STATE_UNLINK		2		/* HC may still see this */
+#define	QH_STATE_IDLE		3		/* HC doesn't see this */
+#define	QH_STATE_UNLINK_WAIT	4		/* LINKED and on reclaim q */
+#define	QH_STATE_COMPLETING	5		/* don't touch token.HALT */
+
+	/* periodic schedule info */
+	u8			usecs;		/* intr bandwidth */
+	u8			gap_uf;		/* uframes split/csplit gap */
+	u8			c_usecs;	/* ... split completion bw */
+	u16			tt_usecs;	/* tt downstream bandwidth */
+	unsigned short		period;		/* polling interval */
+	unsigned short		start;		/* where polling starts */
+#define NO_FRAME ((unsigned short)~0)			/* pick new start */
+	struct usb_device	*dev;		/* access to TT */
+} __attribute__ ((aligned(32)));
+
+/*
+ * Proper OXU210HP structs
+ */
+
+#define OXU_OTG_CORE_OFFSET	0x00400
+#define OXU_OTG_CAP_OFFSET	(OXU_OTG_CORE_OFFSET + 0x100)
+#define OXU_SPH_CORE_OFFSET	0x00800
+#define OXU_SPH_CAP_OFFSET	(OXU_SPH_CORE_OFFSET + 0x100)
+
+#define OXU_OTG_MEM		0xE000
+#define OXU_SPH_MEM		0x16000
+
+/* Only how many elements & element structure are specifies here. */
+/* 2 host controllers are enabled - total size <= 28 kbytes */
+#define	DEFAULT_I_TDPS		1024
+#define QHEAD_NUM		16
+#define QTD_NUM			32
+#define SITD_NUM		8
+#define MURB_NUM		8
+
+#define BUFFER_NUM		8
+#define BUFFER_SIZE		512
+
+struct oxu_info {
+	struct usb_hcd *hcd[2];
+};
+
+struct oxu_buf {
+	u8			buffer[BUFFER_SIZE];
+} __attribute__ ((aligned(BUFFER_SIZE)));
+
+struct oxu_onchip_mem {
+	struct oxu_buf		db_pool[BUFFER_NUM];
+
+	u32			frame_list[DEFAULT_I_TDPS];
+	struct ehci_qh		qh_pool[QHEAD_NUM];
+	struct ehci_qtd		qtd_pool[QTD_NUM];
+} __attribute__ ((aligned(4 << 10)));
+
+#define	EHCI_MAX_ROOT_PORTS	15		/* see HCS_N_PORTS */
+
+struct oxu_murb {
+	struct urb		urb;
+	struct urb		*main;
+	u8			last;
+};
+
+struct oxu_hcd {				/* one per controller */
+	unsigned int		is_otg:1;
+
+	u8			qh_used[QHEAD_NUM];
+	u8			qtd_used[QTD_NUM];
+	u8			db_used[BUFFER_NUM];
+	u8			murb_used[MURB_NUM];
+
+	struct oxu_onchip_mem	__iomem *mem;
+	spinlock_t		mem_lock;
+
+	struct timer_list	urb_timer;
+
+	struct ehci_caps __iomem *caps;
+	struct ehci_regs __iomem *regs;
+
+	__u32			hcs_params;	/* cached register copy */
+	spinlock_t		lock;
+
+	/* async schedule support */
+	struct ehci_qh		*async;
+	struct ehci_qh		*reclaim;
+	unsigned		reclaim_ready:1;
+	unsigned		scanning:1;
+
+	/* periodic schedule support */
+	unsigned		periodic_size;
+	__le32			*periodic;	/* hw periodic table */
+	dma_addr_t		periodic_dma;
+	unsigned		i_thresh;	/* uframes HC might cache */
+
+	union ehci_shadow	*pshadow;	/* mirror hw periodic table */
+	int			next_uframe;	/* scan periodic, start here */
+	unsigned		periodic_sched;	/* periodic activity count */
+
+	/* per root hub port */
+	unsigned long		reset_done[EHCI_MAX_ROOT_PORTS];
+	/* bit vectors (one bit per port) */
+	unsigned long		bus_suspended;	/* which ports were
+						 * already suspended at the
+						 * start of a bus suspend
+						 */
+	unsigned long		companion_ports;/* which ports are dedicated
+						 * to the companion controller
+						 */
+
+	struct timer_list	watchdog;
+	unsigned long		actions;
+	unsigned		stamp;
+	unsigned long		next_statechange;
+	u32			command;
+
+	/* SILICON QUIRKS */
+	struct list_head	urb_list;	/* this is the head to urb
+						 * queue that didn't get enough
+						 * resources
+						 */
+	struct oxu_murb		*murb_pool;	/* murb per split big urb */
+	unsigned urb_len;
+
+	u8			sbrn;		/* packed release number */
+};
+
+#define EHCI_IAA_JIFFIES	(HZ/100)	/* arbitrary; ~10 msec */
+#define EHCI_IO_JIFFIES	 	(HZ/10)		/* io watchdog > irq_thresh */
+#define EHCI_ASYNC_JIFFIES      (HZ/20)		/* async idle timeout */
+#define EHCI_SHRINK_JIFFIES     (HZ/200)	/* async qh unlink delay */
+
+enum ehci_timer_action {
+	TIMER_IO_WATCHDOG,
+	TIMER_IAA_WATCHDOG,
+	TIMER_ASYNC_SHRINK,
+	TIMER_ASYNC_OFF,
+};
+
+#include <linux/oxu210hp.h>