1 files changed, 198 insertions, 0 deletions
diff --git a/Documentation/PCI/PCIEBUS-HOWTO.txt b/Documentation/PCI/PCIEBUS-HOWTO.txt
new file mode 100644
index 000000000..15f0bb3b5
--- /dev/null
+++ b/Documentation/PCI/PCIEBUS-HOWTO.txt
@@ -0,0 +1,198 @@
+		The PCI Express Port Bus Driver Guide HOWTO
+	Tom L Nguyen tom.l.nguyen@intel.com
+			11/03/2004
+
+1. About this guide
+
+This guide describes the basics of the PCI Express Port Bus driver
+and provides information on how to enable the service drivers to
+register/unregister with the PCI Express Port Bus Driver.
+
+2. Copyright 2004 Intel Corporation
+
+3. What is the PCI Express Port Bus Driver
+
+A PCI Express Port is a logical PCI-PCI Bridge structure. There
+are two types of PCI Express Port: the Root Port and the Switch
+Port. The Root Port originates a PCI Express link from a PCI Express
+Root Complex and the Switch Port connects PCI Express links to
+internal logical PCI buses. The Switch Port, which has its secondary
+bus representing the switch's internal routing logic, is called the
+switch's Upstream Port. The switch's Downstream Port is bridging from
+switch's internal routing bus to a bus representing the downstream
+PCI Express link from the PCI Express Switch.
+
+A PCI Express Port can provide up to four distinct functions,
+referred to in this document as services, depending on its port type.
+PCI Express Port's services include native hotplug support (HP),
+power management event support (PME), advanced error reporting
+support (AER), and virtual channel support (VC). These services may
+be handled by a single complex driver or be individually distributed
+and handled by corresponding service drivers.
+
+4. Why use the PCI Express Port Bus Driver?
+
+In existing Linux kernels, the Linux Device Driver Model allows a
+physical device to be handled by only a single driver. The PCI
+Express Port is a PCI-PCI Bridge device with multiple distinct
+services. To maintain a clean and simple solution each service
+may have its own software service driver. In this case several
+service drivers will compete for a single PCI-PCI Bridge device.
+For example, if the PCI Express Root Port native hotplug service
+driver is loaded first, it claims a PCI-PCI Bridge Root Port. The
+kernel therefore does not load other service drivers for that Root
+Port. In other words, it is impossible to have multiple service
+drivers load and run on a PCI-PCI Bridge device simultaneously
+using the current driver model.
+
+To enable multiple service drivers running simultaneously requires
+having a PCI Express Port Bus driver, which manages all populated
+PCI Express Ports and distributes all provided service requests
+to the corresponding service drivers as required. Some key
+advantages of using the PCI Express Port Bus driver are listed below:
+
+	- Allow multiple service drivers to run simultaneously on
+	  a PCI-PCI Bridge Port device.
+
+	- Allow service drivers implemented in an independent
+	  staged approach.
+
+	- Allow one service driver to run on multiple PCI-PCI Bridge
+	  Port devices.
+
+	- Manage and distribute resources of a PCI-PCI Bridge Port
+	  device to requested service drivers.
+
+5. Configuring the PCI Express Port Bus Driver vs. Service Drivers
+
+5.1 Including the PCI Express Port Bus Driver Support into the Kernel
+
+Including the PCI Express Port Bus driver depends on whether the PCI
+Express support is included in the kernel config. The kernel will
+automatically include the PCI Express Port Bus driver as a kernel
+driver when the PCI Express support is enabled in the kernel.
+
+5.2 Enabling Service Driver Support
+
+PCI device drivers are implemented based on Linux Device Driver Model.
+All service drivers are PCI device drivers. As discussed above, it is
+impossible to load any service driver once the kernel has loaded the
+PCI Express Port Bus Driver. To meet the PCI Express Port Bus Driver
+Model requires some minimal changes on existing service drivers that
+imposes no impact on the functionality of existing service drivers.
+
+A service driver is required to use the two APIs shown below to
+register its service with the PCI Express Port Bus driver (see
+section 5.2.1 & 5.2.2). It is important that a service driver
+initializes the pcie_port_service_driver data structure, included in
+header file /include/linux/pcieport_if.h, before calling these APIs.
+Failure to do so will result an identity mismatch, which prevents
+the PCI Express Port Bus driver from loading a service driver.
+
+5.2.1 pcie_port_service_register
+
+int pcie_port_service_register(struct pcie_port_service_driver *new)
+
+This API replaces the Linux Driver Model's pci_register_driver API. A
+service driver should always calls pcie_port_service_register at
+module init. Note that after service driver being loaded, calls
+such as pci_enable_device(dev) and pci_set_master(dev) are no longer
+necessary since these calls are executed by the PCI Port Bus driver.
+
+5.2.2 pcie_port_service_unregister
+
+void pcie_port_service_unregister(struct pcie_port_service_driver *new)
+
+pcie_port_service_unregister replaces the Linux Driver Model's
+pci_unregister_driver. It's always called by service driver when a
+module exits.
+
+5.2.3 Sample Code
+
+Below is sample service driver code to initialize the port service
+driver data structure.
+
+static struct pcie_port_service_id service_id[] = { {
+	.vendor = PCI_ANY_ID,
+	.device = PCI_ANY_ID,
+	.port_type = PCIE_RC_PORT,
+	.service_type = PCIE_PORT_SERVICE_AER,
+	}, { /* end: all zeroes */ }
+};
+
+static struct pcie_port_service_driver root_aerdrv = {
+	.name		= (char *)device_name,
+	.id_table	= &service_id[0],
+
+	.probe		= aerdrv_load,
+	.remove		= aerdrv_unload,
+
+	.suspend	= aerdrv_suspend,
+	.resume		= aerdrv_resume,
+};
+
+Below is a sample code for registering/unregistering a service
+driver.
+
+static int __init aerdrv_service_init(void)
+{
+	int retval = 0;
+
+	retval = pcie_port_service_register(&root_aerdrv);
+	if (!retval) {
+		/*
+		 * FIX ME
+		 */
+	}
+	return retval;
+}
+
+static void __exit aerdrv_service_exit(void)
+{
+	pcie_port_service_unregister(&root_aerdrv);
+}
+
+module_init(aerdrv_service_init);
+module_exit(aerdrv_service_exit);
+
+6. Possible Resource Conflicts
+
+Since all service drivers of a PCI-PCI Bridge Port device are
+allowed to run simultaneously, below lists a few of possible resource
+conflicts with proposed solutions.
+
+6.1 MSI and MSI-X Vector Resource
+
+Once MSI or MSI-X interrupts are enabled on a device, it stays in this
+mode until they are disabled again.  Since service drivers of the same
+PCI-PCI Bridge port share the same physical device, if an individual
+service driver enables or disables MSI/MSI-X mode it may result
+unpredictable behavior.
+
+To avoid this situation all service drivers are not permitted to
+switch interrupt mode on its device. The PCI Express Port Bus driver
+is responsible for determining the interrupt mode and this should be
+transparent to service drivers. Service drivers need to know only
+the vector IRQ assigned to the field irq of struct pcie_device, which
+is passed in when the PCI Express Port Bus driver probes each service
+driver. Service drivers should use (struct pcie_device*)dev->irq to
+call request_irq/free_irq. In addition, the interrupt mode is stored
+in the field interrupt_mode of struct pcie_device.
+
+6.3 PCI Memory/IO Mapped Regions
+
+Service drivers for PCI Express Power Management (PME), Advanced
+Error Reporting (AER), Hot-Plug (HP) and Virtual Channel (VC) access
+PCI configuration space on the PCI Express port. In all cases the
+registers accessed are independent of each other. This patch assumes
+that all service drivers will be well behaved and not overwrite
+other service driver's configuration settings.
+
+6.4 PCI Config Registers
+
+Each service driver runs its PCI config operations on its own
+capability structure except the PCI Express capability structure, in
+which Root Control register and Device Control register are shared
+between PME and AER. This patch assumes that all service drivers
+will be well behaved and not overwrite other service driver's
+configuration settings.