diff options
Diffstat (limited to '')
197 files changed, 12293 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/clock/actions,owl-cmu.txt b/Documentation/devicetree/bindings/clock/actions,owl-cmu.txt new file mode 100644 index 000000000..d1e60d297 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/actions,owl-cmu.txt @@ -0,0 +1,49 @@ +* Actions Semi Owl Clock Management Unit (CMU) + +The Actions Semi Owl Clock Management Unit generates and supplies clock +to various controllers within the SoC. The clock binding described here is +applicable to S900 and S700 SoC's. + +Required Properties: + +- compatible: should be one of the following, + "actions,s900-cmu" + "actions,s700-cmu" +- reg: physical base address of the controller and length of memory mapped + region. +- clocks: Reference to the parent clocks ("hosc", "losc") +- #clock-cells: should be 1. + +Each clock is assigned an identifier, and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in corresponding +dt-bindings/clock/actions,s900-cmu.h or actions,s700-cmu.h header and can be +used in device tree sources. + +External clocks: + +The hosc clock used as input for the plls is generated outside the SoC. It is +expected that it is defined using standard clock bindings as "hosc". + +Actions Semi S900 CMU also requires one more clock: + - "losc" - internal low frequency oscillator + +Example: Clock Management Unit node: + + cmu: clock-controller@e0160000 { + compatible = "actions,s900-cmu"; + reg = <0x0 0xe0160000 0x0 0x1000>; + clocks = <&hosc>, <&losc>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes clock generated by the clock +management unit: + + uart: serial@e012a000 { + compatible = "actions,s900-uart", "actions,owl-uart"; + reg = <0x0 0xe012a000 0x0 0x2000>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cmu CLK_UART5>; + }; diff --git a/Documentation/devicetree/bindings/clock/alphascale,acc.txt b/Documentation/devicetree/bindings/clock/alphascale,acc.txt new file mode 100644 index 000000000..b3205b21c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/alphascale,acc.txt @@ -0,0 +1,114 @@ +Alphascale Clock Controller + +The ACC (Alphascale Clock Controller) is responsible of choising proper +clock source, setting deviders and clock gates. + +Required properties for the ACC node: + - compatible: must be "alphascale,asm9260-clock-controller" + - reg: must contain the ACC register base and size + - #clock-cells : shall be set to 1. + +Simple one-cell clock specifier format is used, where the only cell is used +as an index of the clock inside the provider. +It is encouraged to use dt-binding for clock index definitions. SoC specific +dt-binding should be included to the device tree descriptor. For example +Alphascale ASM9260: +#include <dt-bindings/clock/alphascale,asm9260.h> + +This binding contains two types of clock providers: + _AHB_ - AHB gate; + _SYS_ - adjustable clock source. Not all peripheral have _SYS_ clock provider. +All clock specific details can be found in the SoC documentation. +CLKID_AHB_ROM 0 +CLKID_AHB_RAM 1 +CLKID_AHB_GPIO 2 +CLKID_AHB_MAC 3 +CLKID_AHB_EMI 4 +CLKID_AHB_USB0 5 +CLKID_AHB_USB1 6 +CLKID_AHB_DMA0 7 +CLKID_AHB_DMA1 8 +CLKID_AHB_UART0 9 +CLKID_AHB_UART1 10 +CLKID_AHB_UART2 11 +CLKID_AHB_UART3 12 +CLKID_AHB_UART4 13 +CLKID_AHB_UART5 14 +CLKID_AHB_UART6 15 +CLKID_AHB_UART7 16 +CLKID_AHB_UART8 17 +CLKID_AHB_UART9 18 +CLKID_AHB_I2S0 19 +CLKID_AHB_I2C0 20 +CLKID_AHB_I2C1 21 +CLKID_AHB_SSP0 22 +CLKID_AHB_IOCONFIG 23 +CLKID_AHB_WDT 24 +CLKID_AHB_CAN0 25 +CLKID_AHB_CAN1 26 +CLKID_AHB_MPWM 27 +CLKID_AHB_SPI0 28 +CLKID_AHB_SPI1 29 +CLKID_AHB_QEI 30 +CLKID_AHB_QUADSPI0 31 +CLKID_AHB_CAMIF 32 +CLKID_AHB_LCDIF 33 +CLKID_AHB_TIMER0 34 +CLKID_AHB_TIMER1 35 +CLKID_AHB_TIMER2 36 +CLKID_AHB_TIMER3 37 +CLKID_AHB_IRQ 38 +CLKID_AHB_RTC 39 +CLKID_AHB_NAND 40 +CLKID_AHB_ADC0 41 +CLKID_AHB_LED 42 +CLKID_AHB_DAC0 43 +CLKID_AHB_LCD 44 +CLKID_AHB_I2S1 45 +CLKID_AHB_MAC1 46 + +CLKID_SYS_CPU 47 +CLKID_SYS_AHB 48 +CLKID_SYS_I2S0M 49 +CLKID_SYS_I2S0S 50 +CLKID_SYS_I2S1M 51 +CLKID_SYS_I2S1S 52 +CLKID_SYS_UART0 53 +CLKID_SYS_UART1 54 +CLKID_SYS_UART2 55 +CLKID_SYS_UART3 56 +CLKID_SYS_UART4 56 +CLKID_SYS_UART5 57 +CLKID_SYS_UART6 58 +CLKID_SYS_UART7 59 +CLKID_SYS_UART8 60 +CLKID_SYS_UART9 61 +CLKID_SYS_SPI0 62 +CLKID_SYS_SPI1 63 +CLKID_SYS_QUADSPI 64 +CLKID_SYS_SSP0 65 +CLKID_SYS_NAND 66 +CLKID_SYS_TRACE 67 +CLKID_SYS_CAMM 68 +CLKID_SYS_WDT 69 +CLKID_SYS_CLKOUT 70 +CLKID_SYS_MAC 71 +CLKID_SYS_LCD 72 +CLKID_SYS_ADCANA 73 + +Example of clock consumer with _SYS_ and _AHB_ sinks. +uart4: serial@80010000 { + compatible = "alphascale,asm9260-uart"; + reg = <0x80010000 0x4000>; + clocks = <&acc CLKID_SYS_UART4>, <&acc CLKID_AHB_UART4>; + interrupts = <19>; +}; + +Clock consumer with only one, _AHB_ sink. +timer0: timer@80088000 { + compatible = "alphascale,asm9260-timer"; + reg = <0x80088000 0x4000>; + clocks = <&acc CLKID_AHB_TIMER0>; + interrupts = <29>; +}; + diff --git a/Documentation/devicetree/bindings/clock/altr_socfpga.txt b/Documentation/devicetree/bindings/clock/altr_socfpga.txt new file mode 100644 index 000000000..f72e80e0d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/altr_socfpga.txt @@ -0,0 +1,30 @@ +Device Tree Clock bindings for Altera's SoCFPGA platform + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "altr,socfpga-pll-clock" - for a PLL clock + "altr,socfpga-perip-clock" - The peripheral clock divided from the + PLL clock. + "altr,socfpga-gate-clk" - Clocks that directly feed peripherals and + can get gated. + +- reg : shall be the control register offset from CLOCK_MANAGER's base for the clock. +- clocks : shall be the input parent clock phandle for the clock. This is + either an oscillator or a pll output. +- #clock-cells : from common clock binding, shall be set to 0. + +Optional properties: +- fixed-divider : If clocks have a fixed divider value, use this property. +- clk-gate : For "socfpga-gate-clk", clk-gate contains the gating register + and the bit index. +- div-reg : For "socfpga-gate-clk" and "socfpga-periph-clock", div-reg contains + the divider register, bit shift, and width. +- clk-phase : For the sdmmc_clk, contains the value of the clock phase that controls + the SDMMC CIU clock. The first value is the clk_sample(smpsel), and the second + value is the cclk_in_drv(drvsel). The clk-phase is used to enable the correct + hold/delay times that is needed for the SD/MMC CIU clock. The values of both + can be 0-315 degrees, in 45 degree increments. diff --git a/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt new file mode 100644 index 000000000..61777ad24 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/amlogic,axg-audio-clkc.txt @@ -0,0 +1,56 @@ +* Amlogic AXG Audio Clock Controllers + +The Amlogic AXG audio clock controller generates and supplies clock to the +other elements of the audio subsystem, such as fifos, i2s, spdif and pdm +devices. + +Required Properties: + +- compatible : should be "amlogic,axg-audio-clkc" for the A113X and A113D +- reg : physical base address of the clock controller and length of + memory mapped region. +- clocks : a list of phandle + clock-specifier pairs for the clocks listed + in clock-names. +- clock-names : must contain the following: + * "pclk" - Main peripheral bus clock + may contain the following: + * "mst_in[0-7]" - 8 input plls to generate clock signals + * "slv_sclk[0-9]" - 10 slave bit clocks provided by external + components. + * "slv_lrclk[0-9]" - 10 slave sample clocks provided by external + components. +- resets : phandle of the internal reset line +- #clock-cells : should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/axg-audio-clkc.h header and can be +used in device tree sources. + +Example: + +clkc_audio: clock-controller@0 { + compatible = "amlogic,axg-audio-clkc"; + reg = <0x0 0x0 0x0 0xb4>; + #clock-cells = <1>; + + clocks = <&clkc CLKID_AUDIO>, + <&clkc CLKID_MPLL0>, + <&clkc CLKID_MPLL1>, + <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL3>, + <&clkc CLKID_HIFI_PLL>, + <&clkc CLKID_FCLK_DIV3>, + <&clkc CLKID_FCLK_DIV4>, + <&clkc CLKID_GP0_PLL>; + clock-names = "pclk", + "mst_in0", + "mst_in1", + "mst_in2", + "mst_in3", + "mst_in4", + "mst_in5", + "mst_in6", + "mst_in7"; + resets = <&reset RESET_AUDIO>; +}; diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt new file mode 100644 index 000000000..3a8805280 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-aoclkc.txt @@ -0,0 +1,55 @@ +* Amlogic GXBB AO Clock and Reset Unit + +The Amlogic GXBB AO clock controller generates and supplies clock to various +controllers within the Always-On part of the SoC. + +Required Properties: + +- compatible: value should be different for each SoC family as : + - GXBB (S905) : "amlogic,meson-gxbb-aoclkc" + - GXL (S905X, S905D) : "amlogic,meson-gxl-aoclkc" + - GXM (S912) : "amlogic,meson-gxm-aoclkc" + - AXG (A113D, A113X) : "amlogic,meson-axg-aoclkc" + followed by the common "amlogic,meson-gx-aoclkc" + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/gxbb-aoclkc.h header and can be +used in device tree sources. + +- #reset-cells: should be 1. + +Each reset is assigned an identifier and client nodes can use this identifier +to specify the reset which they consume. All available resets are defined as +preprocessor macros in the dt-bindings/reset/gxbb-aoclkc.h header and can be +used in device tree sources. + +Parent node should have the following properties : +- compatible: "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd" +- reg: base address and size of the AO system control register space. + +Example: AO Clock controller node: + +ao_sysctrl: sys-ctrl@0 { + compatible = "amlogic,meson-gx-ao-sysctrl", "syscon", "simple-mfd"; + reg = <0x0 0x0 0x0 0x100>; + + clkc_AO: clock-controller { + compatible = "amlogic,meson-gxbb-aoclkc", "amlogic,meson-gx-aoclkc"; + #clock-cells = <1>; + #reset-cells = <1>; + }; +}; + +Example: UART controller node that consumes the clock and reset generated + by the clock controller: + + uart_AO: serial@4c0 { + compatible = "amlogic,meson-uart"; + reg = <0x4c0 0x14>; + interrupts = <0 90 1>; + clocks = <&clkc_AO CLKID_AO_UART1>; + resets = <&clkc_AO RESET_AO_UART1>; + }; diff --git a/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt new file mode 100644 index 000000000..e95059956 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/amlogic,gxbb-clkc.txt @@ -0,0 +1,45 @@ +* Amlogic GXBB Clock and Reset Unit + +The Amlogic GXBB clock controller generates and supplies clock to various +controllers within the SoC. + +Required Properties: + +- compatible: should be: + "amlogic,gxbb-clkc" for GXBB SoC, + "amlogic,gxl-clkc" for GXL and GXM SoC, + "amlogic,axg-clkc" for AXG SoC. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/gxbb-clkc.h header and can be +used in device tree sources. + +Parent node should have the following properties : +- compatible: "syscon", "simple-mfd, and "amlogic,meson-gx-hhi-sysctrl" or + "amlogic,meson-axg-hhi-sysctrl" +- reg: base address and size of the HHI system control register space. + +Example: Clock controller node: + +sysctrl: system-controller@0 { + compatible = "amlogic,meson-gx-hhi-sysctrl", "syscon", "simple-mfd"; + reg = <0 0 0 0x400>; + + clkc: clock-controller { + #clock-cells = <1>; + compatible = "amlogic,gxbb-clkc"; + }; +}; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart_AO: serial@c81004c0 { + compatible = "amlogic,meson-uart"; + reg = <0xc81004c0 0x14>; + interrupts = <0 90 1>; + clocks = <&clkc CLKID_CLK81>; + }; diff --git a/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt new file mode 100644 index 000000000..b455c5aa9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt @@ -0,0 +1,49 @@ +* Amlogic Meson8, Meson8b and Meson8m2 Clock and Reset Unit + +The Amlogic Meson8 / Meson8b / Meson8m2 clock controller generates and +supplies clock to various controllers within the SoC. + +Required Properties: + +- compatible: must be one of: + - "amlogic,meson8-clkc" for Meson8 (S802) SoCs + - "amlogic,meson8b-clkc" for Meson8 (S805) SoCs + - "amlogic,meson8m2-clkc" for Meson8m2 (S812) SoCs +- reg: it must be composed by two tuples: + 0) physical base address of the xtal register and length of memory + mapped region. + 1) physical base address of the clock controller and length of memory + mapped region. + +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/meson8b-clkc.h header and can be +used in device tree sources. + +Similarly a preprocessor macro for each reset line is defined in +dt-bindings/reset/amlogic,meson8b-clkc-reset.h (which can be used from the +device tree sources). + + +Example: Clock controller node: + + clkc: clock-controller@c1104000 { + compatible = "amlogic,meson8b-clkc"; + reg = <0xc1108000 0x4>, <0xc1104000 0x460>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart_AO: serial@c81004c0 { + compatible = "amlogic,meson-uart"; + reg = <0xc81004c0 0x14>; + interrupts = <0 90 1>; + clocks = <&clkc CLKID_CLK81>; + }; diff --git a/Documentation/devicetree/bindings/clock/arm-integrator.txt b/Documentation/devicetree/bindings/clock/arm-integrator.txt new file mode 100644 index 000000000..11f5f95f5 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/arm-integrator.txt @@ -0,0 +1,34 @@ +Clock bindings for ARM Integrator and Versatile Core Module clocks + +Auxiliary Oscillator Clock + +This is a configurable clock fed from a 24 MHz chrystal, +used for generating e.g. video clocks. It is located on the +core module and there is only one of these. + +This clock node *must* be a subnode of the core module, since +it obtains the base address for it's address range from its +parent node. + + +Required properties: +- compatible: must be "arm,integrator-cm-auxosc" or "arm,versatile-cm-auxosc" +- #clock-cells: must be <0> + +Optional properties: +- clocks: parent clock(s) + +Example: + +core-module@10000000 { + xtal24mhz: xtal24mhz@24M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <24000000>; + }; + auxosc: cm_aux_osc@25M { + #clock-cells = <0>; + compatible = "arm,integrator-cm-auxosc"; + clocks = <&xtal24mhz>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt new file mode 100644 index 000000000..4cd817420 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/arm-syscon-icst.txt @@ -0,0 +1,70 @@ +ARM System Controller ICST clocks + +The ICS525 and ICS307 oscillators are produced by Integrated Devices +Technology (IDT). ARM integrated these oscillators deeply into their +reference designs by adding special control registers that manage such +oscillators to their system controllers. + +The various ARM system controllers contain logic to serialize and initialize +an ICST clock request after a write to the 32 bit register at an offset +into the system controller. Furthermore, to even be able to alter one of +these frequencies, the system controller must first be unlocked by +writing a special token to another offset in the system controller. + +Some ARM hardware contain special versions of the serial interface that only +connects the low 8 bits of the VDW (missing one bit), hardwires RDW to +different values and sometimes also hardwire the output divider. They +therefore have special compatible strings as per this table (the OD value is +the value on the pins, not the resulting output divider): + +Hardware variant: RDW OD VDW + +Integrator/AP 22 1 Bit 8 0, rest variable +integratorap-cm + +Integrator/AP 46 3 Bit 8 0, rest variable +integratorap-sys + +Integrator/AP 22 or 1 17 or (33 or 25 MHz) +integratorap-pci 14 1 14 + +Integrator/CP 22 variable Bit 8 0, rest variable +integratorcp-cm-core + +Integrator/CP 22 variable Bit 8 0, rest variable +integratorcp-cm-mem + +The ICST oscillator must be provided inside a system controller node. + +Required properties: +- compatible: must be one of + "arm,syscon-icst525" + "arm,syscon-icst307" + "arm,syscon-icst525-integratorap-cm" + "arm,syscon-icst525-integratorap-sys" + "arm,syscon-icst525-integratorap-pci" + "arm,syscon-icst525-integratorcp-cm-core" + "arm,syscon-icst525-integratorcp-cm-mem" +- lock-offset: the offset address into the system controller where the + unlocking register is located +- vco-offset: the offset address into the system controller where the + ICST control register is located (even 32 bit address) +- #clock-cells: must be <0> +- clocks: parent clock, since the ICST needs a parent clock to derive its + frequency from, this attribute is compulsory. + +Example: + +syscon: syscon@10000000 { + compatible = "syscon"; + reg = <0x10000000 0x1000>; + + oscclk0: osc0@c { + compatible = "arm,syscon-icst307"; + #clock-cells = <0>; + lock-offset = <0x20>; + vco-offset = <0x0c>; + clocks = <&xtal24mhz>; + }; + (...) +}; diff --git a/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt b/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt new file mode 100644 index 000000000..1e3370ba1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/armada3700-periph-clock.txt @@ -0,0 +1,70 @@ +* Peripheral Clock bindings for Marvell Armada 37xx SoCs + +Marvell Armada 37xx SoCs provide peripheral clocks which are +used as clock source for the peripheral of the SoC. + +There are two different blocks associated to north bridge and south +bridge. + +The peripheral clock consumer should specify the desired clock by +having the clock ID in its "clocks" phandle cell. + +The following is a list of provided IDs for Armada 370 North bridge clocks: +ID Clock name Description +----------------------------------- +0 mmc MMC controller +1 sata_host Sata Host +2 sec_at Security AT +3 sac_dap Security DAP +4 tsecm Security Engine +5 setm_tmx Serial Embedded Trace Module +6 avs Adaptive Voltage Scaling +7 sqf SPI +8 pwm PWM +9 i2c_2 I2C 2 +10 i2c_1 I2C 1 +11 ddr_phy DDR PHY +12 ddr_fclk DDR F clock +13 trace Trace +14 counter Counter +15 eip97 EIP 97 +16 cpu CPU + +The following is a list of provided IDs for Armada 370 South bridge clocks: +ID Clock name Description +----------------------------------- +0 gbe-50 50 MHz parent clock for Gigabit Ethernet +1 gbe-core parent clock for Gigabit Ethernet core +2 gbe-125 125 MHz parent clock for Gigabit Ethernet +3 gbe1-50 50 MHz clock for Gigabit Ethernet port 1 +4 gbe0-50 50 MHz clock for Gigabit Ethernet port 0 +5 gbe1-125 125 MHz clock for Gigabit Ethernet port 1 +6 gbe0-125 125 MHz clock for Gigabit Ethernet port 0 +7 gbe1-core Gigabit Ethernet core port 1 +8 gbe0-core Gigabit Ethernet core port 0 +9 gbe-bm Gigabit Ethernet Buffer Manager +10 sdio SDIO +11 usb32-sub2-sys USB 2 clock +12 usb32-ss-sys USB 3 clock + +Required properties: + +- compatible : shall be "marvell,armada-3700-periph-clock-nb" for the + north bridge block, or + "marvell,armada-3700-periph-clock-sb" for the south bridge block +- reg : must be the register address of North/South Bridge Clock register +- #clock-cells : from common clock binding; shall be set to 1 + +- clocks : list of the parent clock phandle in the following order: + TBG-A P, TBG-B P, TBG-A S, TBG-B S and finally the xtal clock. + + +Example: + +nb_perih_clk: nb-periph-clk@13000{ + compatible = "marvell,armada-3700-periph-clock-nb"; + reg = <0x13000 0x1000>; + clocks = <&tbg 0>, <&tbg 1>, <&tbg 2>, + <&tbg 3>, <&xtalclk>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/armada3700-tbg-clock.txt b/Documentation/devicetree/bindings/clock/armada3700-tbg-clock.txt new file mode 100644 index 000000000..0ba1d83ff --- /dev/null +++ b/Documentation/devicetree/bindings/clock/armada3700-tbg-clock.txt @@ -0,0 +1,27 @@ +* Time Base Generator Clock bindings for Marvell Armada 37xx SoCs + +Marvell Armada 37xx SoCs provde Time Base Generator clocks which are +used as parent clocks for the peripheral clocks. + +The TBG clock consumer should specify the desired clock by having the +clock ID in its "clocks" phandle cell. + +The following is a list of provided IDs and clock names on Armada 3700: + 0 = TBG A P + 1 = TBG B P + 2 = TBG A S + 3 = TBG B S + +Required properties: +- compatible : shall be "marvell,armada-3700-tbg-clock" +- reg : must be the register address of North Bridge PLL register +- #clock-cells : from common clock binding; shall be set to 1 + +Example: + +tbg: tbg@13200 { + compatible = "marvell,armada-3700-tbg-clock"; + reg = <0x13200 0x1000>; + clocks = <&xtalclk>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt b/Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt new file mode 100644 index 000000000..4c0807f28 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/armada3700-xtal-clock.txt @@ -0,0 +1,29 @@ +* Xtal Clock bindings for Marvell Armada 37xx SoCs + +Marvell Armada 37xx SoCs allow to determine the xtal clock frequencies by +reading the gpio latch register. + +This node must be a subnode of the node exposing the register address +of the GPIO block where the gpio latch is located. +See Documentation/devicetree/bindings/pinctrl/marvell,armada-37xx-pinctrl.txt + +Required properties: +- compatible : shall be one of the following: + "marvell,armada-3700-xtal-clock" +- #clock-cells : from common clock binding; shall be set to 0 + +Optional properties: +- clock-output-names : from common clock binding; allows overwrite default clock + output names ("xtal") + +Example: +pinctrl_nb: pinctrl-nb@13800 { + compatible = "armada3710-nb-pinctrl", "syscon", "simple-mfd"; + reg = <0x13800 0x100>, <0x13C00 0x20>; + + xtalclk: xtal-clk { + compatible = "marvell,armada-3700-xtal-clock"; + clock-output-names = "xtal"; + #clock-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/artpec6.txt b/Documentation/devicetree/bindings/clock/artpec6.txt new file mode 100644 index 000000000..dff9cdf00 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/artpec6.txt @@ -0,0 +1,41 @@ +* Clock bindings for Axis ARTPEC-6 chip + +The bindings are based on the clock provider binding in +Documentation/devicetree/bindings/clock/clock-bindings.txt + +External clocks: +---------------- + +There are two external inputs to the main clock controller which should be +provided using the common clock bindings. +- "sys_refclk": External 50 Mhz oscillator (required) +- "i2s_refclk": Alternate audio reference clock (optional). + +Main clock controller +--------------------- + +Required properties: +- #clock-cells: Should be <1> + See dt-bindings/clock/axis,artpec6-clkctrl.h for the list of valid identifiers. +- compatible: Should be "axis,artpec6-clkctrl" +- reg: Must contain the base address and length of the system controller +- clocks: Must contain a phandle entry for each clock in clock-names +- clock-names: Must include the external oscillator ("sys_refclk"). Optional + ones are the audio reference clock ("i2s_refclk") and the audio fractional + dividers ("frac_clk0" and "frac_clk1"). + +Examples: + +ext_clk: ext_clk { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <50000000>; +}; + +clkctrl: clkctrl@f8000000 { + #clock-cells = <1>; + compatible = "axis,artpec6-clkctrl"; + reg = <0xf8000000 0x48>; + clocks = <&ext_clk>; + clock-names = "sys_refclk"; +}; diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt new file mode 100644 index 000000000..8f8f95056 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -0,0 +1,536 @@ +Device Tree Clock bindings for arch-at91 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "atmel,at91sam9x5-sckc" or + "atmel,sama5d4-sckc": + at91 SCKC (Slow Clock Controller) + This node contains the slow clock definitions. + + "atmel,at91sam9x5-clk-slow-osc": + at91 slow oscillator + + "atmel,at91sam9x5-clk-slow-rc-osc": + at91 internal slow RC oscillator + + "atmel,<chip>-pmc": + at91 PMC (Power Management Controller) + All at91 specific clocks (clocks defined below) must be child + node of the PMC node. + <chip> can be: at91rm9200, at91sam9260, at91sam9261, + at91sam9263, at91sam9g45, at91sam9n12, at91sam9rl, at91sam9x5, + sama5d2, sama5d3 or sama5d4. + + "atmel,at91sam9x5-clk-slow" (under sckc node) + or + "atmel,at91sam9260-clk-slow" (under pmc node): + at91 slow clk + + "atmel,at91rm9200-clk-main-osc" + "atmel,at91sam9x5-clk-main-rc-osc" + at91 main clk sources + + "atmel,at91sam9x5-clk-main" + "atmel,at91rm9200-clk-main": + at91 main clock + + "atmel,at91rm9200-clk-master" or + "atmel,at91sam9x5-clk-master": + at91 master clock + + "atmel,at91sam9x5-clk-peripheral" or + "atmel,at91rm9200-clk-peripheral": + at91 peripheral clocks + + "atmel,at91rm9200-clk-pll" or + "atmel,at91sam9g45-clk-pll" or + "atmel,at91sam9g20-clk-pllb" or + "atmel,sama5d3-clk-pll": + at91 pll clocks + + "atmel,at91sam9x5-clk-plldiv": + at91 plla divisor + + "atmel,at91rm9200-clk-programmable" or + "atmel,at91sam9g45-clk-programmable" or + "atmel,at91sam9x5-clk-programmable": + at91 programmable clocks + + "atmel,at91sam9x5-clk-smd": + at91 SMD (Soft Modem) clock + + "atmel,at91rm9200-clk-system": + at91 system clocks + + "atmel,at91rm9200-clk-usb" or + "atmel,at91sam9x5-clk-usb" or + "atmel,at91sam9n12-clk-usb": + at91 usb clock + + "atmel,at91sam9x5-clk-utmi": + at91 utmi clock + + "atmel,sama5d4-clk-h32mx": + at91 h32mx clock + + "atmel,sama5d2-clk-generated": + at91 generated clock + + "atmel,sama5d2-clk-audio-pll-frac": + at91 audio fractional pll + + "atmel,sama5d2-clk-audio-pll-pad": + at91 audio pll CLK_AUDIO output pin + + "atmel,sama5d2-clk-audio-pll-pmc" + at91 audio pll output on AUDIOPLLCLK that feeds the PMC + and can be used by peripheral clock or generic clock + + "atmel,sama5d2-clk-i2s-mux" (under pmc node): + at91 I2S clock source selection + +Required properties for SCKC node: +- reg : defines the IO memory reserved for the SCKC. +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). + + +For example: + sckc: sckc@fffffe50 { + compatible = "atmel,sama5d3-pmc"; + reg = <0xfffffe50 0x4> + #size-cells = <0>; + #address-cells = <1>; + + /* put at91 slow clocks here */ + }; + + +Required properties for internal slow RC oscillator: +- #clock-cells : from common clock binding; shall be set to 0. +- clock-frequency : define the internal RC oscillator frequency. + +Optional properties: +- clock-accuracy : define the internal RC oscillator accuracy. + +For example: + slow_rc_osc: slow_rc_osc { + compatible = "atmel,at91sam9x5-clk-slow-rc-osc"; + clock-frequency = <32768>; + clock-accuracy = <50000000>; + }; + +Required properties for slow oscillator: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main osc source clk sources (see atmel datasheet). + +Optional properties: +- atmel,osc-bypass : boolean property. Set this when a clock signal is directly + provided on XIN. + +For example: + slow_osc: slow_osc { + compatible = "atmel,at91rm9200-clk-slow-osc"; + #clock-cells = <0>; + clocks = <&slow_xtal>; + }; + +Required properties for slow clock: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the slow clk sources (see atmel datasheet). + +For example: + clk32k: slck { + compatible = "atmel,at91sam9x5-clk-slow"; + #clock-cells = <0>; + clocks = <&slow_rc_osc &slow_osc>; + }; + +Required properties for PMC node: +- reg : defines the IO memory reserved for the PMC. +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- interrupts : shall be set to PMC interrupt line. +- interrupt-controller : tell that the PMC is an interrupt controller. +- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id, + and reflect the bit position in the PMC_ER/DR/SR registers. + You can use the dt macros defined in dt-bindings/clock/at91.h. + 0 (AT91_PMC_MOSCS) -> main oscillator ready + 1 (AT91_PMC_LOCKA) -> PLL A ready + 2 (AT91_PMC_LOCKB) -> PLL B ready + 3 (AT91_PMC_MCKRDY) -> master clock ready + 6 (AT91_PMC_LOCKU) -> UTMI PLL clock ready + 8 .. 15 (AT91_PMC_PCKRDY(id)) -> programmable clock ready + 16 (AT91_PMC_MOSCSELS) -> main oscillator selected + 17 (AT91_PMC_MOSCRCS) -> RC main oscillator stabilized + 18 (AT91_PMC_CFDEV) -> clock failure detected + +For example: + pmc: pmc@fffffc00 { + compatible = "atmel,sama5d3-pmc"; + interrupts = <1 4 7>; + interrupt-controller; + #interrupt-cells = <2>; + #size-cells = <0>; + #address-cells = <1>; + + /* put at91 clocks here */ + }; + +Required properties for main clock internal RC oscillator: +- interrupts : shall be set to "<0>". +- clock-frequency : define the internal RC oscillator frequency. + +Optional properties: +- clock-accuracy : define the internal RC oscillator accuracy. + +For example: + main_rc_osc: main_rc_osc { + compatible = "atmel,at91sam9x5-clk-main-rc-osc"; + interrupt-parent = <&pmc>; + interrupts = <0>; + clock-frequency = <12000000>; + clock-accuracy = <50000000>; + }; + +Required properties for main clock oscillator: +- interrupts : shall be set to "<0>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main osc source clk sources (see atmel datasheet). + +Optional properties: +- atmel,osc-bypass : boolean property. Specified if a clock signal is provided + on XIN. + + clock signal is directly provided on XIN pin. + +For example: + main_osc: main_osc { + compatible = "atmel,at91rm9200-clk-main-osc"; + interrupt-parent = <&pmc>; + interrupts = <0>; + #clock-cells = <0>; + clocks = <&main_xtal>; + }; + +Required properties for main clock: +- interrupts : shall be set to "<0>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main clk sources (see atmel datasheet). + +For example: + main: mainck { + compatible = "atmel,at91sam9x5-clk-main"; + interrupt-parent = <&pmc>; + interrupts = <0>; + #clock-cells = <0>; + clocks = <&main_rc_osc &main_osc>; + }; + +Required properties for master clock: +- interrupts : shall be set to "<3>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the master clock sources (see atmel datasheet) phandles. + e.g. "<&ck32k>, <&main>, <&plla>, <&pllb>". +- atmel,clk-output-range : minimum and maximum clock frequency (two u32 + fields). + e.g. output = <0 133000000>; <=> 0 to 133MHz. +- atmel,clk-divisors : master clock divisors table (four u32 fields). + 0 <=> reserved value. + e.g. divisors = <1 2 4 6>; +- atmel,master-clk-have-div3-pres : some SoC use the reserved value 7 in the + PRES field as CLOCK_DIV3 (e.g sam9x5). + +For example: + mck: mck { + compatible = "atmel,at91rm9200-clk-master"; + interrupt-parent = <&pmc>; + interrupts = <3>; + #clock-cells = <0>; + atmel,clk-output-range = <0 133000000>; + atmel,clk-divisors = <1 2 4 0>; + }; + +Required properties for peripheral clocks: +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- clocks : shall be the master clock phandle. + e.g. clocks = <&mck>; +- name: device tree node describing a specific peripheral clock. + * #clock-cells : from common clock binding; shall be set to 0. + * reg: peripheral id. See Atmel's datasheets to get a full + list of peripheral ids. + * atmel,clk-output-range : minimum and maximum clock frequency + (two u32 fields). Only valid on at91sam9x5-clk-peripheral + compatible IPs. + +For example: + periph: periphck { + compatible = "atmel,at91sam9x5-clk-peripheral"; + #size-cells = <0>; + #address-cells = <1>; + clocks = <&mck>; + + ssc0_clk { + #clock-cells = <0>; + reg = <2>; + atmel,clk-output-range = <0 133000000>; + }; + + usart0_clk { + #clock-cells = <0>; + reg = <3>; + atmel,clk-output-range = <0 66000000>; + }; + }; + + +Required properties for pll clocks: +- interrupts : shall be set to "<1>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the main clock phandle. +- reg : pll id. + 0 -> PLL A + 1 -> PLL B +- atmel,clk-input-range : minimum and maximum source clock frequency (two u32 + fields). + e.g. input = <1 32000000>; <=> 1 to 32MHz. +- #atmel,pll-clk-output-range-cells : number of cells reserved for pll output + range description. Sould be set to 2, 3 + or 4. + * 1st and 2nd cells represent the frequency range (min-max). + * 3rd cell is optional and represents the OUT field value for the given + range. + * 4th cell is optional and represents the ICPLL field (PLLICPR + register) +- atmel,pll-clk-output-ranges : pll output frequency ranges + optional parameter + depending on #atmel,pll-output-range-cells + property value. + +For example: + plla: pllack { + compatible = "atmel,at91sam9g45-clk-pll"; + interrupt-parent = <&pmc>; + interrupts = <1>; + #clock-cells = <0>; + clocks = <&main>; + reg = <0>; + atmel,clk-input-range = <2000000 32000000>; + #atmel,pll-clk-output-range-cells = <4>; + atmel,pll-clk-output-ranges = <74500000 800000000 0 0 + 69500000 750000000 1 0 + 64500000 700000000 2 0 + 59500000 650000000 3 0 + 54500000 600000000 0 1 + 49500000 550000000 1 1 + 44500000 500000000 2 1 + 40000000 450000000 3 1>; + }; + +Required properties for plldiv clocks (plldiv = pll / 2): +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the plla clock phandle. + +The pll divisor is equal to 2 and cannot be changed. + +For example: + plladiv: plladivck { + compatible = "atmel,at91sam9x5-clk-plldiv"; + #clock-cells = <0>; + clocks = <&plla>; + }; + +Required properties for programmable clocks: +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- clocks : shall be the programmable clock source phandles. + e.g. clocks = <&clk32k>, <&main>, <&plla>, <&pllb>; +- name: device tree node describing a specific prog clock. + * #clock-cells : from common clock binding; shall be set to 0. + * reg : programmable clock id (register offset from PCKx + register). + * interrupts : shall be set to "<(8 + id)>". + +For example: + prog: progck { + compatible = "atmel,at91sam9g45-clk-programmable"; + #size-cells = <0>; + #address-cells = <1>; + interrupt-parent = <&pmc>; + clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>; + + prog0 { + #clock-cells = <0>; + reg = <0>; + interrupts = <8>; + }; + + prog1 { + #clock-cells = <0>; + reg = <1>; + interrupts = <9>; + }; + }; + + +Required properties for smd clock: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the smd clock source phandles. + e.g. clocks = <&plladiv>, <&utmi>; + +For example: + smd: smdck { + compatible = "atmel,at91sam9x5-clk-smd"; + #clock-cells = <0>; + clocks = <&plladiv>, <&utmi>; + }; + +Required properties for system clocks: +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- name: device tree node describing a specific system clock. + * #clock-cells : from common clock binding; shall be set to 0. + * reg: system clock id (bit position in SCER/SCDR/SCSR registers). + See Atmel's datasheet to get a full list of system clock ids. + +For example: + system: systemck { + compatible = "atmel,at91rm9200-clk-system"; + #address-cells = <1>; + #size-cells = <0>; + + ddrck { + #clock-cells = <0>; + reg = <2>; + clocks = <&mck>; + }; + + uhpck { + #clock-cells = <0>; + reg = <6>; + clocks = <&usb>; + }; + + udpck { + #clock-cells = <0>; + reg = <7>; + clocks = <&usb>; + }; + }; + + +Required properties for usb clock: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the smd clock source phandles. + e.g. clocks = <&pllb>; +- atmel,clk-divisors (only available for "atmel,at91rm9200-clk-usb"): + usb clock divisor table. + e.g. divisors = <1 2 4 0>; + +For example: + usb: usbck { + compatible = "atmel,at91sam9x5-clk-usb"; + #clock-cells = <0>; + clocks = <&plladiv>, <&utmi>; + }; + + usb: usbck { + compatible = "atmel,at91rm9200-clk-usb"; + #clock-cells = <0>; + clocks = <&pllb>; + atmel,clk-divisors = <1 2 4 0>; + }; + + +Required properties for utmi clock: +- interrupts : shall be set to "<AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the main clock source phandle. + +For example: + utmi: utmick { + compatible = "atmel,at91sam9x5-clk-utmi"; + interrupt-parent = <&pmc>; + interrupts = <AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>; + #clock-cells = <0>; + clocks = <&main>; + }; + +Required properties for 32 bits bus Matrix clock (h32mx clock): +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the master clock source phandle. + +For example: + h32ck: h32mxck { + #clock-cells = <0>; + compatible = "atmel,sama5d4-clk-h32mx"; + clocks = <&mck>; + }; + +Required properties for generated clocks: +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- clocks : shall be the generated clock source phandles. + e.g. clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>; +- name: device tree node describing a specific generated clock. + * #clock-cells : from common clock binding; shall be set to 0. + * reg: peripheral id. See Atmel's datasheets to get a full + list of peripheral ids. + * atmel,clk-output-range : minimum and maximum clock frequency + (two u32 fields). + +For example: + gck { + compatible = "atmel,sama5d2-clk-generated"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>; + + tcb0_gclk: tcb0_gclk { + #clock-cells = <0>; + reg = <35>; + atmel,clk-output-range = <0 83000000>; + }; + + pwm_gclk: pwm_gclk { + #clock-cells = <0>; + reg = <38>; + atmel,clk-output-range = <0 83000000>; + }; + }; + +Required properties for I2S mux clocks: +- #size-cells : shall be 0 (reg is used to encode I2S bus id). +- #address-cells : shall be 1 (reg is used to encode I2S bus id). +- name: device tree node describing a specific mux clock. + * #clock-cells : from common clock binding; shall be set to 0. + * clocks : shall be the mux clock parent phandles; shall be 2 phandles: + peripheral and generated clock; the first phandle shall belong to the + peripheral clock and the second one shall belong to the generated + clock; "clock-indices" property can be user to specify + the correct order. + * reg: I2S bus id of the corresponding mux clock. + e.g. reg = <0>; for i2s0, reg = <1>; for i2s1 + +For example: + i2s_clkmux { + compatible = "atmel,sama5d2-clk-i2s-mux"; + #address-cells = <1>; + #size-cells = <0>; + + i2s0muxck: i2s0_muxclk { + clocks = <&i2s0_clk>, <&i2s0_gclk>; + #clock-cells = <0>; + reg = <0>; + }; + + i2s1muxck: i2s1_muxclk { + clocks = <&i2s1_clk>, <&i2s1_gclk>; + #clock-cells = <0>; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/axi-clkgen.txt b/Documentation/devicetree/bindings/clock/axi-clkgen.txt new file mode 100644 index 000000000..aca94fe94 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/axi-clkgen.txt @@ -0,0 +1,25 @@ +Binding for the axi-clkgen clock generator + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "adi,axi-clkgen-1.00.a" or "adi,axi-clkgen-2.00.a". +- #clock-cells : from common clock binding; Should always be set to 0. +- reg : Address and length of the axi-clkgen register set. +- clocks : Phandle and clock specifier for the parent clock(s). This must + either reference one clock if only the first clock input is connected or two + if both clock inputs are connected. For the later case the clock connected + to the first input must be specified first. + +Optional properties: +- clock-output-names : From common clock binding. + +Example: + clock@ff000000 { + compatible = "adi,axi-clkgen"; + #clock-cells = <0>; + reg = <0xff000000 0x1000>; + clocks = <&osc 1>; + }; diff --git a/Documentation/devicetree/bindings/clock/axs10x-i2s-pll-clock.txt b/Documentation/devicetree/bindings/clock/axs10x-i2s-pll-clock.txt new file mode 100644 index 000000000..5ffc8df7e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/axs10x-i2s-pll-clock.txt @@ -0,0 +1,25 @@ +Binding for the AXS10X I2S PLL clock + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: shall be "snps,axs10x-i2s-pll-clock" +- reg : address and length of the I2S PLL register set. +- clocks: shall be the input parent clock phandle for the PLL. +- #clock-cells: from common clock binding; Should always be set to 0. + +Example: + pll_clock: pll_clock { + compatible = "fixed-clock"; + clock-frequency = <27000000>; + #clock-cells = <0>; + }; + + i2s_clock@100a0 { + compatible = "snps,axs10x-i2s-pll-clock"; + reg = <0x100a0 0x10>; + clocks = <&pll_clock>; + #clock-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt new file mode 100644 index 000000000..4acfc8f64 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-aux-clock.txt @@ -0,0 +1,31 @@ +Broadcom BCM2835 auxiliary peripheral support + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +The auxiliary peripherals (UART, SPI1, and SPI2) have a small register +area controlling clock gating to the peripherals, and providing an IRQ +status register. + +Required properties: +- compatible: Should be "brcm,bcm2835-aux" +- #clock-cells: Should be <1>. The permitted clock-specifier values can be + found in include/dt-bindings/clock/bcm2835-aux.h +- reg: Specifies base physical address and size of the registers +- clocks: The parent clock phandle + +Example: + + clocks: cprman@7e101000 { + compatible = "brcm,bcm2835-cprman"; + #clock-cells = <1>; + reg = <0x7e101000 0x2000>; + clocks = <&clk_osc>; + }; + + aux: aux@7e215004 { + compatible = "brcm,bcm2835-aux"; + #clock-cells = <1>; + reg = <0x7e215000 0x8>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + }; diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt new file mode 100644 index 000000000..dd906db34 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt @@ -0,0 +1,58 @@ +Broadcom BCM2835 CPRMAN clocks + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CPRMAN clock controller generates clocks in the audio power domain +of the BCM2835. There is a level of PLLs deriving from an external +oscillator, a level of PLL dividers that produce channels off of the +few PLLs, and a level of mostly-generic clock generators sourcing from +the PLL channels. Most other hardware components source from the +clock generators, but a few (like the ARM or HDMI) will source from +the PLL dividers directly. + +Required properties: +- compatible: Should be "brcm,bcm2835-cprman" +- #clock-cells: Should be <1>. The permitted clock-specifier values can be + found in include/dt-bindings/clock/bcm2835.h +- reg: Specifies base physical address and size of the registers +- clocks: phandles to the parent clocks used as input to the module, in + the following order: + + - External oscillator + - DSI0 byte clock + - DSI0 DDR2 clock + - DSI0 DDR clock + - DSI1 byte clock + - DSI1 DDR2 clock + - DSI1 DDR clock + + Only external oscillator is required. The DSI clocks may + not be present, in which case their children will be + unusable. + +Example: + + clk_osc: clock@3 { + compatible = "fixed-clock"; + reg = <3>; + #clock-cells = <0>; + clock-output-names = "osc"; + clock-frequency = <19200000>; + }; + + clocks: cprman@7e101000 { + compatible = "brcm,bcm2835-cprman"; + #clock-cells = <1>; + reg = <0x7e101000 0x2000>; + clocks = <&clk_osc>; + }; + + i2c0: i2c@7e205000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e205000 0x1000>; + interrupts = <2 21>; + clocks = <&clocks BCM2835_CLOCK_VPU>; + #address-cells = <1>; + #size-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm53573-ilp.txt b/Documentation/devicetree/bindings/clock/brcm,bcm53573-ilp.txt new file mode 100644 index 000000000..2ebb10733 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,bcm53573-ilp.txt @@ -0,0 +1,36 @@ +Broadcom BCM53573 ILP clock +=========================== + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +This binding is used for ILP clock (sometimes referred as "slow clock") +on Broadcom BCM53573 devices using Cortex-A7 CPU. + +ILP's rate has to be calculated on runtime and it depends on ALP clock +which has to be referenced. + +This clock is part of PMU (Power Management Unit), a Broadcom's device +handing power-related aspects. Its node must be sub-node of the PMU +device. + +Required properties: +- compatible: "brcm,bcm53573-ilp" +- clocks: has to reference an ALP clock +- #clock-cells: should be <0> +- clock-output-names: from common clock bindings, should contain clock + name + +Example: + +pmu@18012000 { + compatible = "simple-mfd", "syscon"; + reg = <0x18012000 0x00001000>; + + ilp { + compatible = "brcm,bcm53573-ilp"; + clocks = <&alp>; + #clock-cells = <0>; + clock-output-names = "ilp"; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt new file mode 100644 index 000000000..ab730ea0a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,iproc-clocks.txt @@ -0,0 +1,313 @@ +Broadcom iProc Family Clocks + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +The iProc clock controller manages clocks that are common to the iProc family. +An SoC from the iProc family may have several PPLs, e.g., ARMPLL, GENPLL, +LCPLL0, MIPIPLL, and etc., all derived from an onboard crystal. Each PLL +comprises of several leaf clocks + +Required properties for a PLL and its leaf clocks: + +- compatible: + Should have a value of the form "brcm,<soc>-<pll>". For example, GENPLL on +Cygnus has a compatible string of "brcm,cygnus-genpll" + +- #clock-cells: + Have a value of <1> since there are more than 1 leaf clock of a given PLL + +- reg: + Define the base and range of the I/O address space that contain the iProc +clock control registers required for the PLL + +- clocks: + The input parent clock phandle for the PLL. For most iProc PLLs, this is an +onboard crystal with a fixed rate + +- clock-output-names: + An ordered list of strings defining the names of the clocks + +Example: + + osc: oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + }; + + genpll: genpll { + #clock-cells = <1>; + compatible = "brcm,cygnus-genpll"; + reg = <0x0301d000 0x2c>, <0x0301c020 0x4>; + clocks = <&osc>; + clock-output-names = "genpll", "axi21", "250mhz", "ihost_sys", + "enet_sw", "audio_125", "can"; + }; + +Required properties for ASIU clocks: + +ASIU clocks are a special case. These clocks are derived directly from the +reference clock of the onboard crystal + +- compatible: + Should have a value of the form "brcm,<soc>-asiu-clk". For example, ASIU +clocks for Cygnus have a compatible string of "brcm,cygnus-asiu-clk" + +- #clock-cells: + Have a value of <1> since there are more than 1 ASIU clocks + +- reg: + Define the base and range of the I/O address space that contain the iProc +clock control registers required for ASIU clocks + +- clocks: + The input parent clock phandle for the ASIU clock, i.e., the onboard +crystal + +- clock-output-names: + An ordered list of strings defining the names of the ASIU clocks + +Example: + + osc: oscillator { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + }; + + asiu_clks: asiu_clks { + #clock-cells = <1>; + compatible = "brcm,cygnus-asiu-clk"; + reg = <0x0301d048 0xc>, <0x180aa024 0x4>; + clocks = <&osc>; + clock-output-names = "keypad", "adc/touch", "pwm"; + }; + +Cygnus +------ +PLL and leaf clock compatible strings for Cygnus are: + "brcm,cygnus-armpll" + "brcm,cygnus-genpll" + "brcm,cygnus-lcpll0" + "brcm,cygnus-mipipll" + "brcm,cygnus-asiu-clk" + "brcm,cygnus-audiopll" + +The following table defines the set of PLL/clock index and ID for Cygnus. +These clock IDs are defined in: + "include/dt-bindings/clock/bcm-cygnus.h" + + Clock Source (Parent) Index ID + --- ----- ----- --------- + crystal N/A N/A N/A + + armpll crystal N/A N/A + + keypad crystal (ASIU) 0 BCM_CYGNUS_ASIU_KEYPAD_CLK + adc/tsc crystal (ASIU) 1 BCM_CYGNUS_ASIU_ADC_CLK + pwm crystal (ASIU) 2 BCM_CYGNUS_ASIU_PWM_CLK + + genpll crystal 0 BCM_CYGNUS_GENPLL + axi21 genpll 1 BCM_CYGNUS_GENPLL_AXI21_CLK + 250mhz genpll 2 BCM_CYGNUS_GENPLL_250MHZ_CLK + ihost_sys genpll 3 BCM_CYGNUS_GENPLL_IHOST_SYS_CLK + enet_sw genpll 4 BCM_CYGNUS_GENPLL_ENET_SW_CLK + audio_125 genpll 5 BCM_CYGNUS_GENPLL_AUDIO_125_CLK + can genpll 6 BCM_CYGNUS_GENPLL_CAN_CLK + + lcpll0 crystal 0 BCM_CYGNUS_LCPLL0 + pcie_phy lcpll0 1 BCM_CYGNUS_LCPLL0_PCIE_PHY_REF_CLK + ddr_phy lcpll0 2 BCM_CYGNUS_LCPLL0_DDR_PHY_CLK + sdio lcpll0 3 BCM_CYGNUS_LCPLL0_SDIO_CLK + usb_phy lcpll0 4 BCM_CYGNUS_LCPLL0_USB_PHY_REF_CLK + smart_card lcpll0 5 BCM_CYGNUS_LCPLL0_SMART_CARD_CLK + ch5_unused lcpll0 6 BCM_CYGNUS_LCPLL0_CH5_UNUSED + + mipipll crystal 0 BCM_CYGNUS_MIPIPLL + ch0_unused mipipll 1 BCM_CYGNUS_MIPIPLL_CH0_UNUSED + ch1_lcd mipipll 2 BCM_CYGNUS_MIPIPLL_CH1_LCD + ch2_v3d mipipll 3 BCM_CYGNUS_MIPIPLL_CH2_V3D + ch3_unused mipipll 4 BCM_CYGNUS_MIPIPLL_CH3_UNUSED + ch4_unused mipipll 5 BCM_CYGNUS_MIPIPLL_CH4_UNUSED + ch5_unused mipipll 6 BCM_CYGNUS_MIPIPLL_CH5_UNUSED + + audiopll crystal 0 BCM_CYGNUS_AUDIOPLL + ch0_audio audiopll 1 BCM_CYGNUS_AUDIOPLL_CH0 + ch1_audio audiopll 2 BCM_CYGNUS_AUDIOPLL_CH1 + ch2_audio audiopll 3 BCM_CYGNUS_AUDIOPLL_CH2 + +Hurricane 2 +------ +PLL and leaf clock compatible strings for Hurricane 2 are: + "brcm,hr2-armpll" + +The following table defines the set of PLL/clock for Hurricane 2: + + Clock Source Index ID + --- ----- ----- --------- + crystal N/A N/A N/A + + armpll crystal N/A N/A + + +Northstar and Northstar Plus +------ +PLL and leaf clock compatible strings for Northstar and Northstar Plus are: + "brcm,nsp-armpll" + "brcm,nsp-genpll" + "brcm,nsp-lcpll0" + +The following table defines the set of PLL/clock index and ID for Northstar and +Northstar Plus. These clock IDs are defined in: + "include/dt-bindings/clock/bcm-nsp.h" + + Clock Source Index ID + --- ----- ----- --------- + crystal N/A N/A N/A + + armpll crystal N/A N/A + + genpll crystal 0 BCM_NSP_GENPLL + phy genpll 1 BCM_NSP_GENPLL_PHY_CLK + ethernetclk genpll 2 BCM_NSP_GENPLL_ENET_SW_CLK + usbclk genpll 3 BCM_NSP_GENPLL_USB_PHY_REF_CLK + iprocfast genpll 4 BCM_NSP_GENPLL_IPROCFAST_CLK + sata1 genpll 5 BCM_NSP_GENPLL_SATA1_CLK + sata2 genpll 6 BCM_NSP_GENPLL_SATA2_CLK + + lcpll0 crystal 0 BCM_NSP_LCPLL0 + pcie_phy lcpll0 1 BCM_NSP_LCPLL0_PCIE_PHY_REF_CLK + sdio lcpll0 2 BCM_NSP_LCPLL0_SDIO_CLK + ddr_phy lcpll0 3 BCM_NSP_LCPLL0_DDR_PHY_CLK + +Northstar 2 +----------- +PLL and leaf clock compatible strings for Northstar 2 are: + "brcm,ns2-genpll-scr" + "brcm,ns2-genpll-sw" + "brcm,ns2-lcpll-ddr" + "brcm,ns2-lcpll-ports" + +The following table defines the set of PLL/clock index and ID for Northstar 2. +These clock IDs are defined in: + "include/dt-bindings/clock/bcm-ns2.h" + + Clock Source Index ID + --- ----- ----- --------- + crystal N/A N/A N/A + + genpll_scr crystal 0 BCM_NS2_GENPLL_SCR + scr genpll_scr 1 BCM_NS2_GENPLL_SCR_SCR_CLK + fs genpll_scr 2 BCM_NS2_GENPLL_SCR_FS_CLK + audio_ref genpll_scr 3 BCM_NS2_GENPLL_SCR_AUDIO_CLK + ch3_unused genpll_scr 4 BCM_NS2_GENPLL_SCR_CH3_UNUSED + ch4_unused genpll_scr 5 BCM_NS2_GENPLL_SCR_CH4_UNUSED + ch5_unused genpll_scr 6 BCM_NS2_GENPLL_SCR_CH5_UNUSED + + genpll_sw crystal 0 BCM_NS2_GENPLL_SW + rpe genpll_sw 1 BCM_NS2_GENPLL_SW_RPE_CLK + 250 genpll_sw 2 BCM_NS2_GENPLL_SW_250_CLK + nic genpll_sw 3 BCM_NS2_GENPLL_SW_NIC_CLK + chimp genpll_sw 4 BCM_NS2_GENPLL_SW_CHIMP_CLK + port genpll_sw 5 BCM_NS2_GENPLL_SW_PORT_CLK + sdio genpll_sw 6 BCM_NS2_GENPLL_SW_SDIO_CLK + + lcpll_ddr crystal 0 BCM_NS2_LCPLL_DDR + pcie_sata_usb lcpll_ddr 1 BCM_NS2_LCPLL_DDR_PCIE_SATA_USB_CLK + ddr lcpll_ddr 2 BCM_NS2_LCPLL_DDR_DDR_CLK + ch2_unused lcpll_ddr 3 BCM_NS2_LCPLL_DDR_CH2_UNUSED + ch3_unused lcpll_ddr 4 BCM_NS2_LCPLL_DDR_CH3_UNUSED + ch4_unused lcpll_ddr 5 BCM_NS2_LCPLL_DDR_CH4_UNUSED + ch5_unused lcpll_ddr 6 BCM_NS2_LCPLL_DDR_CH5_UNUSED + + lcpll_ports crystal 0 BCM_NS2_LCPLL_PORTS + wan lcpll_ports 1 BCM_NS2_LCPLL_PORTS_WAN_CLK + rgmii lcpll_ports 2 BCM_NS2_LCPLL_PORTS_RGMII_CLK + ch2_unused lcpll_ports 3 BCM_NS2_LCPLL_PORTS_CH2_UNUSED + ch3_unused lcpll_ports 4 BCM_NS2_LCPLL_PORTS_CH3_UNUSED + ch4_unused lcpll_ports 5 BCM_NS2_LCPLL_PORTS_CH4_UNUSED + ch5_unused lcpll_ports 6 BCM_NS2_LCPLL_PORTS_CH5_UNUSED + +BCM63138 +-------- +PLL and leaf clock compatible strings for BCM63138 are: + "brcm,bcm63138-armpll" + +Stingray +----------- +PLL and leaf clock compatible strings for Stingray are: + "brcm,sr-genpll0" + "brcm,sr-genpll1" + "brcm,sr-genpll2" + "brcm,sr-genpll3" + "brcm,sr-genpll4" + "brcm,sr-genpll5" + "brcm,sr-genpll6" + + "brcm,sr-lcpll0" + "brcm,sr-lcpll1" + "brcm,sr-lcpll-pcie" + + +The following table defines the set of PLL/clock index and ID for Stingray. +These clock IDs are defined in: + "include/dt-bindings/clock/bcm-sr.h" + + Clock Source Index ID + --- ----- ----- --------- + crystal N/A N/A N/A + crmu_ref25m crystal N/A N/A + + genpll0 crystal 0 BCM_SR_GENPLL0 + clk_125m genpll0 1 BCM_SR_GENPLL0_125M_CLK + clk_scr genpll0 2 BCM_SR_GENPLL0_SCR_CLK + clk_250 genpll0 3 BCM_SR_GENPLL0_250M_CLK + clk_pcie_axi genpll0 4 BCM_SR_GENPLL0_PCIE_AXI_CLK + clk_paxc_axi_x2 genpll0 5 BCM_SR_GENPLL0_PAXC_AXI_X2_CLK + clk_paxc_axi genpll0 6 BCM_SR_GENPLL0_PAXC_AXI_CLK + + genpll1 crystal 0 BCM_SR_GENPLL1 + clk_pcie_tl genpll1 1 BCM_SR_GENPLL1_PCIE_TL_CLK + clk_mhb_apb genpll1 2 BCM_SR_GENPLL1_MHB_APB_CLK + + genpll2 crystal 0 BCM_SR_GENPLL2 + clk_nic genpll2 1 BCM_SR_GENPLL2_NIC_CLK + clk_ts_500_ref genpll2 2 BCM_SR_GENPLL2_TS_500_REF_CLK + clk_125_nitro genpll2 3 BCM_SR_GENPLL2_125_NITRO_CLK + clk_chimp genpll2 4 BCM_SR_GENPLL2_CHIMP_CLK + clk_nic_flash genpll2 5 BCM_SR_GENPLL2_NIC_FLASH_CLK + clk_fs genpll2 6 BCM_SR_GENPLL2_FS_CLK + + genpll3 crystal 0 BCM_SR_GENPLL3 + clk_hsls genpll3 1 BCM_SR_GENPLL3_HSLS_CLK + clk_sdio genpll3 2 BCM_SR_GENPLL3_SDIO_CLK + + genpll4 crystal 0 BCM_SR_GENPLL4 + clk_ccn genpll4 1 BCM_SR_GENPLL4_CCN_CLK + clk_tpiu_pll genpll4 2 BCM_SR_GENPLL4_TPIU_PLL_CLK + clk_noc genpll4 3 BCM_SR_GENPLL4_NOC_CLK + clk_chclk_fs4 genpll4 4 BCM_SR_GENPLL4_CHCLK_FS4_CLK + clk_bridge_fscpu genpll4 5 BCM_SR_GENPLL4_BRIDGE_FSCPU_CLK + + genpll5 crystal 0 BCM_SR_GENPLL5 + clk_fs4_hf genpll5 1 BCM_SR_GENPLL5_FS4_HF_CLK + clk_crypto_ae genpll5 2 BCM_SR_GENPLL5_CRYPTO_AE_CLK + clk_raid_ae genpll5 3 BCM_SR_GENPLL5_RAID_AE_CLK + + genpll6 crystal 0 BCM_SR_GENPLL6 + clk_48_usb genpll6 1 BCM_SR_GENPLL6_48_USB_CLK + + lcpll0 crystal 0 BCM_SR_LCPLL0 + clk_sata_refp lcpll0 1 BCM_SR_LCPLL0_SATA_REFP_CLK + clk_sata_refn lcpll0 2 BCM_SR_LCPLL0_SATA_REFN_CLK + clk_sata_350 lcpll0 3 BCM_SR_LCPLL0_SATA_350_CLK + clk_sata_500 lcpll0 4 BCM_SR_LCPLL0_SATA_500_CLK + + lcpll1 crystal 0 BCM_SR_LCPLL1 + clk_wan lcpll1 1 BCM_SR_LCPLL1_WAN_CLK + clk_usb_ref lcpll1 2 BCM_SR_LCPLL1_USB_REF_CLK + clk_crmu_ts lcpll1 3 BCM_SR_LCPLL1_CRMU_TS_CLK + + lcpll_pcie crystal 0 BCM_SR_LCPLL_PCIE + clk_pcie_phy_ref lcpll1 1 BCM_SR_LCPLL_PCIE_PHY_REF_CLK diff --git a/Documentation/devicetree/bindings/clock/brcm,kona-ccu.txt b/Documentation/devicetree/bindings/clock/brcm,kona-ccu.txt new file mode 100644 index 000000000..8e5a7d868 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/brcm,kona-ccu.txt @@ -0,0 +1,138 @@ +Broadcom Kona Family Clocks + +This binding is associated with Broadcom SoCs having "Kona" style +clock control units (CCUs). A CCU is a clock provider that manages +a set of clock signals. Each CCU is represented by a node in the +device tree. + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible + Shall have a value of the form "brcm,<model>-<which>-ccu", + where <model> is a Broadcom SoC model number and <which> is + the name of a defined CCU. For example: + "brcm,bcm11351-root-ccu" + The compatible strings used for each supported SoC family + are defined below. +- reg + Shall define the base and range of the address space + containing clock control registers +- #clock-cells + Shall have value <1>. The permitted clock-specifier values + are defined below. +- clock-output-names + Shall be an ordered list of strings defining the names of + the clocks provided by the CCU. + +Device tree example: + + slave_ccu: slave_ccu { + compatible = "brcm,bcm11351-slave-ccu"; + reg = <0x3e011000 0x0f00>; + #clock-cells = <1>; + clock-output-names = "uartb", + "uartb2", + "uartb3", + "uartb4"; + }; + + ref_crystal_clk: ref_crystal { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <26000000>; + }; + + uart@3e002000 { + compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; + reg = <0x3e002000 0x1000>; + clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB3>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; + +BCM281XX family +--------------- +CCU compatible string values for SoCs in the BCM281XX family are: + "brcm,bcm11351-root-ccu" + "brcm,bcm11351-aon-ccu" + "brcm,bcm11351-hub-ccu" + "brcm,bcm11351-master-ccu" + "brcm,bcm11351-slave-ccu" + +The following table defines the set of CCUs and clock specifiers for +BCM281XX family clocks. When a clock consumer references a clocks, +its symbolic specifier (rather than its numeric index value) should +be used. These specifiers are defined in: + "include/dt-bindings/clock/bcm281xx.h" + + CCU Clock Type Index Specifier + --- ----- ---- ----- --------- + root frac_1m peri 0 BCM281XX_ROOT_CCU_FRAC_1M + + aon hub_timer peri 0 BCM281XX_AON_CCU_HUB_TIMER + aon pmu_bsc peri 1 BCM281XX_AON_CCU_PMU_BSC + aon pmu_bsc_var peri 2 BCM281XX_AON_CCU_PMU_BSC_VAR + + hub tmon_1m peri 0 BCM281XX_HUB_CCU_TMON_1M + + master sdio1 peri 0 BCM281XX_MASTER_CCU_SDIO1 + master sdio2 peri 1 BCM281XX_MASTER_CCU_SDIO2 + master sdio3 peri 2 BCM281XX_MASTER_CCU_SDIO3 + master sdio4 peri 3 BCM281XX_MASTER_CCU_SDIO4 + master dmac peri 4 BCM281XX_MASTER_CCU_DMAC + master usb_ic peri 5 BCM281XX_MASTER_CCU_USB_IC + master hsic2_48m peri 6 BCM281XX_MASTER_CCU_HSIC_48M + master hsic2_12m peri 7 BCM281XX_MASTER_CCU_HSIC_12M + + slave uartb peri 0 BCM281XX_SLAVE_CCU_UARTB + slave uartb2 peri 1 BCM281XX_SLAVE_CCU_UARTB2 + slave uartb3 peri 2 BCM281XX_SLAVE_CCU_UARTB3 + slave uartb4 peri 3 BCM281XX_SLAVE_CCU_UARTB4 + slave ssp0 peri 4 BCM281XX_SLAVE_CCU_SSP0 + slave ssp2 peri 5 BCM281XX_SLAVE_CCU_SSP2 + slave bsc1 peri 6 BCM281XX_SLAVE_CCU_BSC1 + slave bsc2 peri 7 BCM281XX_SLAVE_CCU_BSC2 + slave bsc3 peri 8 BCM281XX_SLAVE_CCU_BSC3 + slave pwm peri 9 BCM281XX_SLAVE_CCU_PWM + + +BCM21664 family +--------------- +CCU compatible string values for SoCs in the BCM21664 family are: + "brcm,bcm21664-root-ccu" + "brcm,bcm21664-aon-ccu" + "brcm,bcm21664-master-ccu" + "brcm,bcm21664-slave-ccu" + +The following table defines the set of CCUs and clock specifiers for +BCM21664 family clocks. When a clock consumer references a clocks, +its symbolic specifier (rather than its numeric index value) should +be used. These specifiers are defined in: + "include/dt-bindings/clock/bcm21664.h" + + CCU Clock Type Index Specifier + --- ----- ---- ----- --------- + root frac_1m peri 0 BCM21664_ROOT_CCU_FRAC_1M + + aon hub_timer peri 0 BCM21664_AON_CCU_HUB_TIMER + + master sdio1 peri 0 BCM21664_MASTER_CCU_SDIO1 + master sdio2 peri 1 BCM21664_MASTER_CCU_SDIO2 + master sdio3 peri 2 BCM21664_MASTER_CCU_SDIO3 + master sdio4 peri 3 BCM21664_MASTER_CCU_SDIO4 + master sdio1_sleep peri 4 BCM21664_MASTER_CCU_SDIO1_SLEEP + master sdio2_sleep peri 5 BCM21664_MASTER_CCU_SDIO2_SLEEP + master sdio3_sleep peri 6 BCM21664_MASTER_CCU_SDIO3_SLEEP + master sdio4_sleep peri 7 BCM21664_MASTER_CCU_SDIO4_SLEEP + + slave uartb peri 0 BCM21664_SLAVE_CCU_UARTB + slave uartb2 peri 1 BCM21664_SLAVE_CCU_UARTB2 + slave uartb3 peri 2 BCM21664_SLAVE_CCU_UARTB3 + slave uartb4 peri 3 BCM21664_SLAVE_CCU_UARTB4 + slave bsc1 peri 4 BCM21664_SLAVE_CCU_BSC1 + slave bsc2 peri 5 BCM21664_SLAVE_CCU_BSC2 + slave bsc3 peri 6 BCM21664_SLAVE_CCU_BSC3 + slave bsc4 peri 7 BCM21664_SLAVE_CCU_BSC4 diff --git a/Documentation/devicetree/bindings/clock/calxeda.txt b/Documentation/devicetree/bindings/clock/calxeda.txt new file mode 100644 index 000000000..0a6ac1bdc --- /dev/null +++ b/Documentation/devicetree/bindings/clock/calxeda.txt @@ -0,0 +1,17 @@ +Device Tree Clock bindings for Calxeda highbank platform + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "calxeda,hb-pll-clock" - for a PLL clock + "calxeda,hb-a9periph-clock" - The A9 peripheral clock divided from the + A9 clock. + "calxeda,hb-a9bus-clock" - The A9 bus clock divided from the A9 clock. + "calxeda,hb-emmc-clock" - Divided clock for MMC/SD controller. +- reg : shall be the control register offset from SYSREGs base for the clock. +- clocks : shall be the input parent clock phandle for the clock. This is + either an oscillator or a pll output. +- #clock-cells : from common clock binding; shall be set to 0. diff --git a/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt b/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt new file mode 100644 index 000000000..6030afb10 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clk-exynos-audss.txt @@ -0,0 +1,103 @@ +* Samsung Audio Subsystem Clock Controller + +The Samsung Audio Subsystem clock controller generates and supplies clocks +to Audio Subsystem block available in the S5PV210 and Exynos SoCs. The clock +binding described here is applicable to all SoCs in Exynos family. + +Required Properties: + +- compatible: should be one of the following: + - "samsung,exynos4210-audss-clock" - controller compatible with all Exynos4 SoCs. + - "samsung,exynos5250-audss-clock" - controller compatible with Exynos5250 + SoCs. + - "samsung,exynos5410-audss-clock" - controller compatible with Exynos5410 + SoCs. + - "samsung,exynos5420-audss-clock" - controller compatible with Exynos5420 + SoCs. +- reg: physical base address and length of the controller's register set. + +- #clock-cells: should be 1. + +- clocks: + - pll_ref: Fixed rate PLL reference clock, parent of mout_audss. "fin_pll" + is used if not specified. + - pll_in: Input PLL to the AudioSS block, parent of mout_audss. "fout_epll" + is used if not specified. + - cdclk: External i2s clock, parent of mout_i2s. "cdclk0" is used if not + specified. + - sclk_audio: Audio bus clock, parent of mout_i2s. "sclk_audio0" is used if + not specified. + - sclk_pcm_in: PCM clock, parent of sclk_pcm. "sclk_pcm0" is used if not + specified. + +- clock-names: Aliases for the above clocks. They should be "pll_ref", + "pll_in", "cdclk", "sclk_audio", and "sclk_pcm_in" respectively. + +Optional Properties: + + - power-domains: a phandle to respective power domain node as described by + generic PM domain bindings (see power/power_domain.txt for more + information). + +The following is the list of clocks generated by the controller. Each clock is +assigned an identifier and client nodes use this identifier to specify the +clock which they consume. Some of the clocks are available only on a particular +Exynos4 SoC and this is specified where applicable. + +Provided clocks: + +Clock ID SoC (if specific) +----------------------------------------------- + +mout_audss 0 +mout_i2s 1 +dout_srp 2 +dout_aud_bus 3 +dout_i2s 4 +srp_clk 5 +i2s_bus 6 +sclk_i2s 7 +pcm_bus 8 +sclk_pcm 9 +adma 10 Exynos5420 + +Example 1: An example of a clock controller node using the default input + clock names is listed below. + +clock_audss: audss-clock-controller@3810000 { + compatible = "samsung,exynos5250-audss-clock"; + reg = <0x03810000 0x0C>; + #clock-cells = <1>; +}; + +Example 2: An example of a clock controller node with the input clocks + specified. + +clock_audss: audss-clock-controller@3810000 { + compatible = "samsung,exynos5250-audss-clock"; + reg = <0x03810000 0x0C>; + #clock-cells = <1>; + clocks = <&clock 1>, <&clock 7>, <&clock 138>, <&clock 160>, + <&ext_i2s_clk>; + clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in", "cdclk"; +}; + +Example 3: I2S controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + +i2s0: i2s@3830000 { + compatible = "samsung,i2s-v5"; + reg = <0x03830000 0x100>; + dmas = <&pdma0 10 + &pdma0 9 + &pdma0 8>; + dma-names = "tx", "rx", "tx-sec"; + clocks = <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_SCLK_I2S>, + <&clock_audss EXYNOS_MOUT_AUDSS>, + <&clock_audss EXYNOS_MOUT_I2S>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1", + "mout_audss", "mout_i2s"; +}; diff --git a/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt b/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt new file mode 100644 index 000000000..4208886d8 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clk-palmas-clk32kg-clocks.txt @@ -0,0 +1,35 @@ +* Palmas 32KHz clocks * + +Palmas device has two clock output pins for 32KHz, KG and KG_AUDIO. + +This binding uses the common clock binding ./clock-bindings.txt. + +Required properties: +- compatible : "ti,palmas-clk32kg" for clk32kg clock + "ti,palmas-clk32kgaudio" for clk32kgaudio clock +- #clock-cells : shall be set to 0. + +Optional property: +- ti,external-sleep-control: The external enable input pins controlled the + enable/disable of clocks. The external enable input pins ENABLE1, + ENABLE2 and NSLEEP. The valid values for the external pins are: + PALMAS_EXT_CONTROL_PIN_ENABLE1 for ENABLE1 pin + PALMAS_EXT_CONTROL_PIN_ENABLE2 for ENABLE2 pin + PALMAS_EXT_CONTROL_PIN_NSLEEP for NSLEEP pin + Option 0 or missing this property means the clock is enabled/disabled + via register access and these pins do not have any control. + The macros of external control pins for DTS is defined at + dt-bindings/mfd/palmas.h + +Example: + #include <dt-bindings/mfd/palmas.h> + ... + palmas: tps65913@58 { + ... + clk32kg: palmas_clk32k@0 { + compatible = "ti,palmas-clk32kg"; + #clock-cells = <0>; + ti,external-sleep-control = <PALMAS_EXT_CONTROL_PIN_NSLEEP>; + }; + ... + }; diff --git a/Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt b/Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt new file mode 100644 index 000000000..f6272dcd9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clk-s5pv210-audss.txt @@ -0,0 +1,53 @@ +* Samsung Audio Subsystem Clock Controller + +The Samsung Audio Subsystem clock controller generates and supplies clocks +to Audio Subsystem block available in the S5PV210 and compatible SoCs. + +Required Properties: + +- compatible: should be "samsung,s5pv210-audss-clock". +- reg: physical base address and length of the controller's register set. + +- #clock-cells: should be 1. + +- clocks: + - hclk: AHB bus clock of the Audio Subsystem. + - xxti: Optional fixed rate PLL reference clock, parent of mout_audss. If + not specified (i.e. xusbxti is used for PLL reference), it is fixed to + a clock named "xxti". + - fout_epll: Input PLL to the AudioSS block, parent of mout_audss. + - iiscdclk0: Optional external i2s clock, parent of mout_i2s. If not + specified, it is fixed to a clock named "iiscdclk0". + - sclk_audio0: Audio bus clock, parent of mout_i2s. + +- clock-names: Aliases for the above clocks. They should be "hclk", + "xxti", "fout_epll", "iiscdclk0", and "sclk_audio0" respectively. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s5pv210-audss-clk.h header and can be used in device +tree sources. + +Example: Clock controller node. + + clk_audss: clock-controller@c0900000 { + compatible = "samsung,s5pv210-audss-clock"; + reg = <0xc0900000 0x1000>; + #clock-cells = <1>; + clock-names = "hclk", "xxti", + "fout_epll", "sclk_audio0"; + clocks = <&clocks DOUT_HCLKP>, <&xxti>, + <&clocks FOUT_EPLL>, <&clocks SCLK_AUDIO0>; + }; + +Example: I2S controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + i2s0: i2s@3830000 { + /* ... */ + clock-names = "iis", "i2s_opclk0", + "i2s_opclk1"; + clocks = <&clk_audss CLK_I2S>, <&clk_audss CLK_I2S>, + <&clk_audss CLK_DOUT_AUD_BUS>; + /* ... */ + }; diff --git a/Documentation/devicetree/bindings/clock/clock-bindings.txt b/Documentation/devicetree/bindings/clock/clock-bindings.txt new file mode 100644 index 000000000..2ec489eeb --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clock-bindings.txt @@ -0,0 +1,170 @@ +This binding is a work-in-progress, and are based on some experimental +work by benh[1]. + +Sources of clock signal can be represented by any node in the device +tree. Those nodes are designated as clock providers. Clock consumer +nodes use a phandle and clock specifier pair to connect clock provider +outputs to clock inputs. Similar to the gpio specifiers, a clock +specifier is an array of zero, one or more cells identifying the clock +output on a device. The length of a clock specifier is defined by the +value of a #clock-cells property in the clock provider node. + +[1] http://patchwork.ozlabs.org/patch/31551/ + +==Clock providers== + +Required properties: +#clock-cells: Number of cells in a clock specifier; Typically 0 for nodes + with a single clock output and 1 for nodes with multiple + clock outputs. + +Optional properties: +clock-output-names: Recommended to be a list of strings of clock output signal + names indexed by the first cell in the clock specifier. + However, the meaning of clock-output-names is domain + specific to the clock provider, and is only provided to + encourage using the same meaning for the majority of clock + providers. This format may not work for clock providers + using a complex clock specifier format. In those cases it + is recommended to omit this property and create a binding + specific names property. + + Clock consumer nodes must never directly reference + the provider's clock-output-names property. + +For example: + + oscillator { + #clock-cells = <1>; + clock-output-names = "ckil", "ckih"; + }; + +- this node defines a device with two clock outputs, the first named + "ckil" and the second named "ckih". Consumer nodes always reference + clocks by index. The names should reflect the clock output signal + names for the device. + +clock-indices: If the identifying number for the clocks in the node + is not linear from zero, then this allows the mapping of + identifiers into the clock-output-names array. + +For example, if we have two clocks <&oscillator 1> and <&oscillator 3>: + + oscillator { + compatible = "myclocktype"; + #clock-cells = <1>; + clock-indices = <1>, <3>; + clock-output-names = "clka", "clkb"; + } + + This ensures we do not have any empty strings in clock-output-names + + +==Clock consumers== + +Required properties: +clocks: List of phandle and clock specifier pairs, one pair + for each clock input to the device. Note: if the + clock provider specifies '0' for #clock-cells, then + only the phandle portion of the pair will appear. + +Optional properties: +clock-names: List of clock input name strings sorted in the same + order as the clocks property. Consumers drivers + will use clock-names to match clock input names + with clocks specifiers. +clock-ranges: Empty property indicating that child nodes can inherit named + clocks from this node. Useful for bus nodes to provide a + clock to their children. + +For example: + + device { + clocks = <&osc 1>, <&ref 0>; + clock-names = "baud", "register"; + }; + + +This represents a device with two clock inputs, named "baud" and "register". +The baud clock is connected to output 1 of the &osc device, and the register +clock is connected to output 0 of the &ref. + +==Example== + + /* external oscillator */ + osc: oscillator { + compatible = "fixed-clock"; + #clock-cells = <1>; + clock-frequency = <32678>; + clock-output-names = "osc"; + }; + + /* phase-locked-loop device, generates a higher frequency clock + * from the external oscillator reference */ + pll: pll@4c000 { + compatible = "vendor,some-pll-interface" + #clock-cells = <1>; + clocks = <&osc 0>; + clock-names = "ref"; + reg = <0x4c000 0x1000>; + clock-output-names = "pll", "pll-switched"; + }; + + /* UART, using the low frequency oscillator for the baud clock, + * and the high frequency switched PLL output for register + * clocking */ + uart@a000 { + compatible = "fsl,imx-uart"; + reg = <0xa000 0x1000>; + interrupts = <33>; + clocks = <&osc 0>, <&pll 1>; + clock-names = "baud", "register"; + }; + +This DT fragment defines three devices: an external oscillator to provide a +low-frequency reference clock, a PLL device to generate a higher frequency +clock signal, and a UART. + +* The oscillator is fixed-frequency, and provides one clock output, named "osc". +* The PLL is both a clock provider and a clock consumer. It uses the clock + signal generated by the external oscillator, and provides two output signals + ("pll" and "pll-switched"). +* The UART has its baud clock connected the external oscillator and its + register clock connected to the PLL clock (the "pll-switched" signal) + +==Assigned clock parents and rates== + +Some platforms may require initial configuration of default parent clocks +and clock frequencies. Such a configuration can be specified in a device tree +node through assigned-clocks, assigned-clock-parents and assigned-clock-rates +properties. The assigned-clock-parents property should contain a list of parent +clocks in the form of a phandle and clock specifier pair and the +assigned-clock-rates property should contain a list of frequencies in Hz. Both +these properties should correspond to the clocks listed in the assigned-clocks +property. + +To skip setting parent or rate of a clock its corresponding entry should be +set to 0, or can be omitted if it is not followed by any non-zero entry. + + uart@a000 { + compatible = "fsl,imx-uart"; + reg = <0xa000 0x1000>; + ... + clocks = <&osc 0>, <&pll 1>; + clock-names = "baud", "register"; + + assigned-clocks = <&clkcon 0>, <&pll 2>; + assigned-clock-parents = <&pll 2>; + assigned-clock-rates = <0>, <460800>; + }; + +In this example the <&pll 2> clock is set as parent of clock <&clkcon 0> and +the <&pll 2> clock is assigned a frequency value of 460800 Hz. + +Configuring a clock's parent and rate through the device node that consumes +the clock can be done only for clocks that have a single user. Specifying +conflicting parent or rate configuration in multiple consumer nodes for +a shared clock is forbidden. + +Configuration of common clocks, which affect multiple consumer devices can +be similarly specified in the clock provider node. diff --git a/Documentation/devicetree/bindings/clock/clps711x-clock.txt b/Documentation/devicetree/bindings/clock/clps711x-clock.txt new file mode 100644 index 000000000..f1bd53f79 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/clps711x-clock.txt @@ -0,0 +1,19 @@ +* Clock bindings for the Cirrus Logic CLPS711X CPUs + +Required properties: +- compatible : Shall contain "cirrus,ep7209-clk". +- reg : Address of the internal register set. +- startup-frequency: Factory set CPU startup frequency in HZ. +- #clock-cells : Should be <1>. + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/clps711x-clock.h +for the full list of CLPS711X clock IDs. + +Example: + clks: clks@80000000 { + #clock-cells = <1>; + compatible = "cirrus,ep7312-clk", "cirrus,ep7209-clk"; + reg = <0x80000000 0xc000>; + startup-frequency = <73728000>; + }; diff --git a/Documentation/devicetree/bindings/clock/cs2000-cp.txt b/Documentation/devicetree/bindings/clock/cs2000-cp.txt new file mode 100644 index 000000000..54e6df0be --- /dev/null +++ b/Documentation/devicetree/bindings/clock/cs2000-cp.txt @@ -0,0 +1,22 @@ +CIRRUS LOGIC Fractional-N Clock Synthesizer & Clock Multiplier + +Required properties: + +- compatible: "cirrus,cs2000-cp" +- reg: The chip select number on the I2C bus +- clocks: common clock binding for CLK_IN, XTI/REF_CLK +- clock-names: CLK_IN : clk_in, XTI/REF_CLK : ref_clk +- #clock-cells: must be <0> + +Example: + +&i2c2 { + ... + cs2000: clk_multiplier@4f { + #clock-cells = <0>; + compatible = "cirrus,cs2000-cp"; + reg = <0x4f>; + clocks = <&rcar_sound 0>, <&x12_clk>; + clock-names = "clk_in", "ref_clk"; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/csr,atlas7-car.txt b/Documentation/devicetree/bindings/clock/csr,atlas7-car.txt new file mode 100644 index 000000000..54d6d1358 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/csr,atlas7-car.txt @@ -0,0 +1,55 @@ +* Clock and reset bindings for CSR atlas7 + +Required properties: +- compatible: Should be "sirf,atlas7-car" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- #reset-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. +The ID list atlas7_clks defined in drivers/clk/sirf/clk-atlas7.c + +The reset consumer should specify the desired reset by having the reset +ID in its "reset" phandle cell. +The ID list atlas7_reset_unit defined in drivers/clk/sirf/clk-atlas7.c + +Examples: Clock and reset controller node: + +car: clock-controller@18620000 { + compatible = "sirf,atlas7-car"; + reg = <0x18620000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; +}; + +Examples: Consumers using clock or reset: + +timer@10dc0000 { + compatible = "sirf,macro-tick"; + reg = <0x10dc0000 0x1000>; + clocks = <&car 54>; + interrupts = <0 0 0>, + <0 1 0>, + <0 2 0>, + <0 49 0>, + <0 50 0>, + <0 51 0>; +}; + +uart1: uart@18020000 { + cell-index = <1>; + compatible = "sirf,macro-uart"; + reg = <0x18020000 0x1000>; + clocks = <&clks 95>; + interrupts = <0 18 0>; + fifosize = <32>; +}; + +vpp@13110000 { + compatible = "sirf,prima2-vpp"; + reg = <0x13110000 0x10000>; + interrupts = <0 31 0>; + clocks = <&car 85>; + resets = <&car 29>; +}; diff --git a/Documentation/devicetree/bindings/clock/dove-divider-clock.txt b/Documentation/devicetree/bindings/clock/dove-divider-clock.txt new file mode 100644 index 000000000..217871f48 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/dove-divider-clock.txt @@ -0,0 +1,28 @@ +PLL divider based Dove clocks + +Marvell Dove has a 2GHz PLL, which feeds into a set of dividers to provide +high speed clocks for a number of peripherals. These dividers are part of +the PMU, and thus this node should be a child of the PMU node. + +The following clocks are provided: + +ID Clock +------------- +0 AXI bus clock +1 GPU clock +2 VMeta clock +3 LCD clock + +Required properties: +- compatible : shall be "marvell,dove-divider-clock" +- reg : shall be the register address of the Core PLL and Clock Divider + Control 0 register. This will cover that register, as well as the + Core PLL and Clock Divider Control 1 register. Thus, it will have + a size of 8. +- #clock-cells : from common clock binding; shall be set to 1 + +divider_clk: core-clock@64 { + compatible = "marvell,dove-divider-clock"; + reg = <0x0064 0x8>; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/efm32-clock.txt b/Documentation/devicetree/bindings/clock/efm32-clock.txt new file mode 100644 index 000000000..263d293f6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/efm32-clock.txt @@ -0,0 +1,11 @@ +* Clock bindings for Energy Micro efm32 Giant Gecko's Clock Management Unit + +Required properties: +- compatible: Should be "efm32gg,cmu" +- reg: Base address and length of the register set +- interrupts: Interrupt used by the CMU +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock ID in +its "clocks" phandle cell. The header efm32-clk.h contains a list of available +IDs. diff --git a/Documentation/devicetree/bindings/clock/emev2-clock.txt b/Documentation/devicetree/bindings/clock/emev2-clock.txt new file mode 100644 index 000000000..268ca6154 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/emev2-clock.txt @@ -0,0 +1,98 @@ +Device tree Clock bindings for Renesas EMMA Mobile EV2 + +This binding uses the common clock binding. + +* SMU +System Management Unit described in user's manual R19UH0037EJ1000_SMU. +This is not a clock provider, but clocks under SMU depend on it. + +Required properties: +- compatible: Should be "renesas,emev2-smu" +- reg: Address and Size of SMU registers + +* SMU_CLKDIV +Function block with an input mux and a divider, which corresponds to +"Serial clock generator" in fig."Clock System Overview" of the manual, +and "xxx frequency division setting register" (XXXCLKDIV) registers. +This makes internal (neither input nor output) clock that is provided +to input of xxxGCLK block. + +Required properties: +- compatible: Should be "renesas,emev2-smu-clkdiv" +- reg: Byte offset from SMU base and Bit position in the register +- clocks: Parent clocks. Input clocks as described in clock-bindings.txt +- #clock-cells: Should be <0> + +* SMU_GCLK +Clock gating node shown as "Clock stop processing block" in the +fig."Clock System Overview" of the manual. +Registers are "xxx clock gate control register" (XXXGCLKCTRL). + +Required properties: +- compatible: Should be "renesas,emev2-smu-gclk" +- reg: Byte offset from SMU base and Bit position in the register +- clocks: Input clock as described in clock-bindings.txt +- #clock-cells: Should be <0> + +Example of provider: + +usia_u0_sclkdiv: usia_u0_sclkdiv { + compatible = "renesas,emev2-smu-clkdiv"; + reg = <0x610 0>; + clocks = <&pll3_fo>, <&pll4_fo>, <&pll1_fo>, <&osc1_fo>; + #clock-cells = <0>; +}; + +usia_u0_sclk: usia_u0_sclk { + compatible = "renesas,emev2-smu-gclk"; + reg = <0x4a0 1>; + clocks = <&usia_u0_sclkdiv>; + #clock-cells = <0>; +}; + +Example of consumer: + +serial@e1020000 { + compatible = "renesas,em-uart"; + reg = <0xe1020000 0x38>; + interrupts = <0 8 0>; + clocks = <&usia_u0_sclk>; + clock-names = "sclk"; +}; + +Example of clock-tree description: + + This describes a clock path in the clock tree + c32ki -> pll3_fo -> usia_u0_sclkdiv -> usia_u0_sclk + +smu@e0110000 { + compatible = "renesas,emev2-smu"; + reg = <0xe0110000 0x10000>; + #address-cells = <2>; + #size-cells = <0>; + + c32ki: c32ki { + compatible = "fixed-clock"; + clock-frequency = <32768>; + #clock-cells = <0>; + }; + pll3_fo: pll3_fo { + compatible = "fixed-factor-clock"; + clocks = <&c32ki>; + clock-div = <1>; + clock-mult = <7000>; + #clock-cells = <0>; + }; + usia_u0_sclkdiv: usia_u0_sclkdiv { + compatible = "renesas,emev2-smu-clkdiv"; + reg = <0x610 0>; + clocks = <&pll3_fo>; + #clock-cells = <0>; + }; + usia_u0_sclk: usia_u0_sclk { + compatible = "renesas,emev2-smu-gclk"; + reg = <0x4a0 1>; + clocks = <&usia_u0_sclkdiv>; + #clock-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/exynos3250-clock.txt b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt new file mode 100644 index 000000000..7441ed519 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos3250-clock.txt @@ -0,0 +1,57 @@ +* Samsung Exynos3250 Clock Controller + +The Exynos3250 clock controller generates and supplies clock to various +controllers within the Exynos3250 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,exynos3250-cmu" - controller compatible with Exynos3250 SoC. + - "samsung,exynos3250-cmu-dmc" - controller compatible with + Exynos3250 SoC for Dynamic Memory Controller domain. + - "samsung,exynos3250-cmu-isp" - ISP block clock controller compatible + with Exynos3250 SOC + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos3250.h header and can be used in device +tree sources. + +Example 1: Examples of clock controller nodes are listed below. + + cmu: clock-controller@10030000 { + compatible = "samsung,exynos3250-cmu"; + reg = <0x10030000 0x20000>; + #clock-cells = <1>; + }; + + cmu_dmc: clock-controller@105c0000 { + compatible = "samsung,exynos3250-cmu-dmc"; + reg = <0x105C0000 0x2000>; + #clock-cells = <1>; + }; + + cmu_isp: clock-controller@10048000 { + compatible = "samsung,exynos3250-cmu-isp"; + reg = <0x10048000 0x1000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@13800000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x13800000 0x100>; + interrupts = <0 109 0>; + clocks = <&cmu CLK_UART0>, <&cmu CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos4-clock.txt b/Documentation/devicetree/bindings/clock/exynos4-clock.txt new file mode 100644 index 000000000..17bb11365 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos4-clock.txt @@ -0,0 +1,86 @@ +* Samsung Exynos4 Clock Controller + +The Exynos4 clock controller generates and supplies clock to various controllers +within the Exynos4 SoC. The clock binding described here is applicable to all +SoC's in the Exynos4 family. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,exynos4210-clock" - controller compatible with Exynos4210 SoC. + - "samsung,exynos4412-clock" - controller compatible with Exynos4412 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos4.h header and can be used in device +tree sources. + +Example 1: An example of a clock controller node is listed below. + + clock: clock-controller@10030000 { + compatible = "samsung,exynos4210-clock"; + reg = <0x10030000 0x20000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@13820000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x13820000 0x100>; + interrupts = <0 54 0>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; + clock-names = "uart", "clk_uart_baud0"; + }; + +Exynos4412 SoC contains some additional clocks for FIMC-ISP (Camera ISP) +subsystem. Registers for those clocks are located in the ISP power domain. +Because those registers are also located in a different memory region than +the main clock controller, a separate clock controller has to be defined for +handling them. + +Required Properties: + +- compatible: should be "samsung,exynos4412-isp-clock". + +- reg: physical base address of the ISP clock controller and length of memory + mapped region. + +- #clock-cells: should be 1. + +- clocks: list of the clock controller input clock identifiers, + from common clock bindings, should point to CLK_ACLK200 and + CLK_ACLK400_MCUISP clocks from the main clock controller. + +- clock-names: list of the clock controller input clock names, + as described in clock-bindings.txt, should be "aclk200" and + "aclk400_mcuisp". + +- power-domains: a phandle to ISP power domain node as described by + generic PM domain bindings. + +Example 3: The clock controllers bindings for Exynos4412 SoCs. + + clock: clock-controller@10030000 { + compatible = "samsung,exynos4412-clock"; + reg = <0x10030000 0x18000>; + #clock-cells = <1>; + }; + + isp_clock: clock-controller@10048000 { + compatible = "samsung,exynos4412-isp-clock"; + reg = <0x10048000 0x1000>; + #clock-cells = <1>; + power-domains = <&pd_isp>; + clocks = <&clock CLK_ACLK200>, <&clock CLK_ACLK400_MCUISP>; + clock-names = "aclk200", "aclk400_mcuisp"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt new file mode 100644 index 000000000..aff266a12 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt @@ -0,0 +1,41 @@ +* Samsung Exynos5250 Clock Controller + +The Exynos5250 clock controller generates and supplies clock to various +controllers within the Exynos5250 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,exynos5250-clock" - controller compatible with Exynos5250 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5250.h header and can be used in device +tree sources. + +Example 1: An example of a clock controller node is listed below. + + clock: clock-controller@10010000 { + compatible = "samsung,exynos5250-clock"; + reg = <0x10010000 0x30000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@13820000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x13820000 0x100>; + interrupts = <0 54 0>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; + clock-names = "uart", "clk_uart_baud0"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos5260-clock.txt b/Documentation/devicetree/bindings/clock/exynos5260-clock.txt new file mode 100644 index 000000000..c79d31f7f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5260-clock.txt @@ -0,0 +1,190 @@ +* Samsung Exynos5260 Clock Controller + +Exynos5260 has 13 clock controllers which are instantiated +independently from the device-tree. These clock controllers +generate and supply clocks to various hardware blocks within +the SoC. + +Each clock is assigned an identifier and client nodes can use +this identifier to specify the clock which they consume. All +available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5260-clk.h header and can be used in +device tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It +is expected that they are defined using standard clock bindings +with following clock-output-names: + + - "fin_pll" - PLL input clock from XXTI + - "xrtcxti" - input clock from XRTCXTI + - "ioclk_pcm_extclk" - pcm external operation clock + - "ioclk_spdif_extclk" - spdif external operation clock + - "ioclk_i2s_cdclk" - i2s0 codec clock + +Phy clocks: + +There are several clocks which are generated by specific PHYs. +These clocks are fed into the clock controller and then routed to +the hardware blocks. These clocks are defined as fixed clocks in the +driver with following names: + + - "phyclk_dptx_phy_ch3_txd_clk" - dp phy clock for channel 3 + - "phyclk_dptx_phy_ch2_txd_clk" - dp phy clock for channel 2 + - "phyclk_dptx_phy_ch1_txd_clk" - dp phy clock for channel 1 + - "phyclk_dptx_phy_ch0_txd_clk" - dp phy clock for channel 0 + - "phyclk_hdmi_phy_tmds_clko" - hdmi phy tmds clock + - "phyclk_hdmi_phy_pixel_clko" - hdmi phy pixel clock + - "phyclk_hdmi_link_o_tmds_clkhi" - hdmi phy for hdmi link + - "phyclk_dptx_phy_o_ref_clk_24m" - dp phy reference clock + - "phyclk_dptx_phy_clk_div2" + - "phyclk_mipi_dphy_4l_m_rxclkesc0" + - "phyclk_usbhost20_phy_phyclock" - usb 2.0 phy clock + - "phyclk_usbhost20_phy_freeclk" + - "phyclk_usbhost20_phy_clk48mohci" + - "phyclk_usbdrd30_udrd30_pipe_pclk" + - "phyclk_usbdrd30_udrd30_phyclock" - usb 3.0 phy clock + +Required Properties for Clock Controller: + + - compatible: should be one of the following. + 1) "samsung,exynos5260-clock-top" + 2) "samsung,exynos5260-clock-peri" + 3) "samsung,exynos5260-clock-egl" + 4) "samsung,exynos5260-clock-kfc" + 5) "samsung,exynos5260-clock-g2d" + 6) "samsung,exynos5260-clock-mif" + 7) "samsung,exynos5260-clock-mfc" + 8) "samsung,exynos5260-clock-g3d" + 9) "samsung,exynos5260-clock-fsys" + 10) "samsung,exynos5260-clock-aud" + 11) "samsung,exynos5260-clock-isp" + 12) "samsung,exynos5260-clock-gscl" + 13) "samsung,exynos5260-clock-disp" + + - reg: physical base address of the controller and the length of + memory mapped region. + + - #clock-cells: should be 1. + + - clocks: list of clock identifiers which are fed as the input to + the given clock controller. Please refer the next section to find + the input clocks for a given controller. + + - clock-names: list of names of clocks which are fed as the input + to the given clock controller. + +Input clocks for top clock controller: + - fin_pll + - dout_mem_pll + - dout_bus_pll + - dout_media_pll + +Input clocks for peri clock controller: + - fin_pll + - ioclk_pcm_extclk + - ioclk_i2s_cdclk + - ioclk_spdif_extclk + - phyclk_hdmi_phy_ref_cko + - dout_aclk_peri_66 + - dout_sclk_peri_uart0 + - dout_sclk_peri_uart1 + - dout_sclk_peri_uart2 + - dout_sclk_peri_spi0_b + - dout_sclk_peri_spi1_b + - dout_sclk_peri_spi2_b + - dout_aclk_peri_aud + - dout_sclk_peri_spi0_b + +Input clocks for egl clock controller: + - fin_pll + - dout_bus_pll + +Input clocks for kfc clock controller: + - fin_pll + - dout_media_pll + +Input clocks for g2d clock controller: + - fin_pll + - dout_aclk_g2d_333 + +Input clocks for mif clock controller: + - fin_pll + +Input clocks for mfc clock controller: + - fin_pll + - dout_aclk_mfc_333 + +Input clocks for g3d clock controller: + - fin_pll + +Input clocks for fsys clock controller: + - fin_pll + - phyclk_usbhost20_phy_phyclock + - phyclk_usbhost20_phy_freeclk + - phyclk_usbhost20_phy_clk48mohci + - phyclk_usbdrd30_udrd30_pipe_pclk + - phyclk_usbdrd30_udrd30_phyclock + - dout_aclk_fsys_200 + +Input clocks for aud clock controller: + - fin_pll + - fout_aud_pll + - ioclk_i2s_cdclk + - ioclk_pcm_extclk + +Input clocks for isp clock controller: + - fin_pll + - dout_aclk_isp1_266 + - dout_aclk_isp1_400 + - mout_aclk_isp1_266 + +Input clocks for gscl clock controller: + - fin_pll + - dout_aclk_gscl_400 + - dout_aclk_gscl_333 + +Input clocks for disp clock controller: + - fin_pll + - phyclk_dptx_phy_ch3_txd_clk + - phyclk_dptx_phy_ch2_txd_clk + - phyclk_dptx_phy_ch1_txd_clk + - phyclk_dptx_phy_ch0_txd_clk + - phyclk_hdmi_phy_tmds_clko + - phyclk_hdmi_phy_ref_clko + - phyclk_hdmi_phy_pixel_clko + - phyclk_hdmi_link_o_tmds_clkhi + - phyclk_mipi_dphy_4l_m_txbyte_clkhs + - phyclk_dptx_phy_o_ref_clk_24m + - phyclk_dptx_phy_clk_div2 + - phyclk_mipi_dphy_4l_m_rxclkesc0 + - phyclk_hdmi_phy_ref_cko + - ioclk_spdif_extclk + - dout_aclk_peri_aud + - dout_aclk_disp_222 + - dout_sclk_disp_pixel + - dout_aclk_disp_333 + +Example 1: An example of a clock controller node is listed below. + + clock_mfc: clock-controller@11090000 { + compatible = "samsung,exynos5260-clock-mfc"; + clock = <&fin_pll>, <&clock_top TOP_DOUT_ACLK_MFC_333>; + clock-names = "fin_pll", "dout_aclk_mfc_333"; + reg = <0x11090000 0x10000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the + peri clock controller. Refer to the standard clock bindings for + information about 'clocks' and 'clock-names' property. + + serial@12c00000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 146 0>; + clocks = <&clock_peri PERI_PCLK_UART0>, <&clock_peri PERI_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; + diff --git a/Documentation/devicetree/bindings/clock/exynos5410-clock.txt b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt new file mode 100644 index 000000000..217beb27c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5410-clock.txt @@ -0,0 +1,50 @@ +* Samsung Exynos5410 Clock Controller + +The Exynos5410 clock controller generates and supplies clock to various +controllers within the Exynos5410 SoC. + +Required Properties: + +- compatible: should be "samsung,exynos5410-clock" + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +- clocks: should contain an entry specifying the root clock from external + oscillator supplied through XXTI or XusbXTI pin. This clock should be + defined using standard clock bindings with "fin_pll" clock-output-name. + That clock is being passed internally to the 9 PLLs. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5410.h header and can be used in device +tree sources. + +Example 1: An example of a clock controller node is listed below. + + fin_pll: xxti { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "fin_pll"; + #clock-cells = <0>; + }; + + clock: clock-controller@10010000 { + compatible = "samsung,exynos5410-clock"; + reg = <0x10010000 0x30000>; + #clock-cells = <1>; + clocks = <&fin_pll>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@12c20000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 51 0>; + clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt new file mode 100644 index 000000000..717a7b153 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt @@ -0,0 +1,42 @@ +* Samsung Exynos5420 Clock Controller + +The Exynos5420 clock controller generates and supplies clock to various +controllers within the Exynos5420 SoC and for the Exynos5800 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,exynos5420-clock" - controller compatible with Exynos5420 SoC. + - "samsung,exynos5800-clock" - controller compatible with Exynos5800 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5420.h header and can be used in device +tree sources. + +Example 1: An example of a clock controller node is listed below. + + clock: clock-controller@10010000 { + compatible = "samsung,exynos5420-clock"; + reg = <0x10010000 0x30000>; + #clock-cells = <1>; + }; + +Example 2: UART controller node that consumes the clock generated by the clock + controller. Refer to the standard clock bindings for information + about 'clocks' and 'clock-names' property. + + serial@13820000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x13820000 0x100>; + interrupts = <0 54 0>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; + clock-names = "uart", "clk_uart_baud0"; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos5433-clock.txt b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt new file mode 100644 index 000000000..50d5897c9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos5433-clock.txt @@ -0,0 +1,484 @@ +* Samsung Exynos5433 CMU (Clock Management Units) + +The Exynos5433 clock controller generates and supplies clock to various +controllers within the Exynos5433 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,exynos5433-cmu-top" - clock controller compatible for CMU_TOP + which generates clocks for IMEM/FSYS/G3D/GSCL/HEVC/MSCL/G2D/MFC/PERIC/PERIS + domains and bus clocks. + - "samsung,exynos5433-cmu-cpif" - clock controller compatible for CMU_CPIF + which generates clocks for LLI (Low Latency Interface) IP. + - "samsung,exynos5433-cmu-mif" - clock controller compatible for CMU_MIF + which generates clocks for DRAM Memory Controller domain. + - "samsung,exynos5433-cmu-peric" - clock controller compatible for CMU_PERIC + which generates clocks for UART/I2C/SPI/I2S/PCM/SPDIF/PWM/SLIMBUS IPs. + - "samsung,exynos5433-cmu-peris" - clock controller compatible for CMU_PERIS + which generates clocks for PMU/TMU/MCT/WDT/RTC/SECKEY/TZPC IPs. + - "samsung,exynos5433-cmu-fsys" - clock controller compatible for CMU_FSYS + which generates clocks for USB/UFS/SDMMC/TSI/PDMA IPs. + - "samsung,exynos5433-cmu-g2d" - clock controller compatible for CMU_G2D + which generates clocks for G2D/MDMA IPs. + - "samsung,exynos5433-cmu-disp" - clock controller compatible for CMU_DISP + which generates clocks for Display (DECON/HDMI/DSIM/MIXER) IPs. + - "samsung,exynos5433-cmu-aud" - clock controller compatible for CMU_AUD + which generates clocks for Cortex-A5/BUS/AUDIO clocks. + - "samsung,exynos5433-cmu-bus0", "samsung,exynos5433-cmu-bus1" + and "samsung,exynos5433-cmu-bus2" - clock controller compatible for CMU_BUS + which generates global data buses clock and global peripheral buses clock. + - "samsung,exynos5433-cmu-g3d" - clock controller compatible for CMU_G3D + which generates clocks for 3D Graphics Engine IP. + - "samsung,exynos5433-cmu-gscl" - clock controller compatible for CMU_GSCL + which generates clocks for GSCALER IPs. + - "samsung,exynos5433-cmu-apollo"- clock controller compatible for CMU_APOLLO + which generates clocks for Cortex-A53 Quad-core processor. + - "samsung,exynos5433-cmu-atlas" - clock controller compatible for CMU_ATLAS + which generates clocks for Cortex-A57 Quad-core processor, CoreSight and + L2 cache controller. + - "samsung,exynos5433-cmu-mscl" - clock controller compatible for CMU_MSCL + which generates clocks for M2M (Memory to Memory) scaler and JPEG IPs. + - "samsung,exynos5433-cmu-mfc" - clock controller compatible for CMU_MFC + which generates clocks for MFC(Multi-Format Codec) IP. + - "samsung,exynos5433-cmu-hevc" - clock controller compatible for CMU_HEVC + which generates clocks for HEVC(High Efficiency Video Codec) decoder IP. + - "samsung,exynos5433-cmu-isp" - clock controller compatible for CMU_ISP + which generates clocks for FIMC-ISP/DRC/SCLC/DIS/3DNR IPs. + - "samsung,exynos5433-cmu-cam0" - clock controller compatible for CMU_CAM0 + which generates clocks for MIPI_CSIS{0|1}/FIMC_LITE_{A|B|D}/FIMC_3AA{0|1} + IPs. + - "samsung,exynos5433-cmu-cam1" - clock controller compatible for CMU_CAM1 + which generates clocks for Cortex-A5/MIPI_CSIS2/FIMC-LITE_C/FIMC-FD IPs. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +- clocks: list of the clock controller input clock identifiers, + from common clock bindings. Please refer the next section + to find the input clocks for a given controller. + +- clock-names: list of the clock controller input clock names, + as described in clock-bindings.txt. + + Input clocks for top clock controller: + - oscclk + - sclk_mphy_pll + - sclk_mfc_pll + - sclk_bus_pll + + Input clocks for cpif clock controller: + - oscclk + + Input clocks for mif clock controller: + - oscclk + - sclk_mphy_pll + + Input clocks for fsys clock controller: + - oscclk + - sclk_ufs_mphy + - aclk_fsys_200 + - sclk_pcie_100_fsys + - sclk_ufsunipro_fsys + - sclk_mmc2_fsys + - sclk_mmc1_fsys + - sclk_mmc0_fsys + - sclk_usbhost30_fsys + - sclk_usbdrd30_fsys + + Input clocks for g2d clock controller: + - oscclk + - aclk_g2d_266 + - aclk_g2d_400 + + Input clocks for disp clock controller: + - oscclk + - sclk_dsim1_disp + - sclk_dsim0_disp + - sclk_dsd_disp + - sclk_decon_tv_eclk_disp + - sclk_decon_vclk_disp + - sclk_decon_eclk_disp + - sclk_decon_tv_vclk_disp + - aclk_disp_333 + + Input clocks for audio clock controller: + - oscclk + - fout_aud_pll + + Input clocks for bus0 clock controller: + - aclk_bus0_400 + + Input clocks for bus1 clock controller: + - aclk_bus1_400 + + Input clocks for bus2 clock controller: + - oscclk + - aclk_bus2_400 + + Input clocks for g3d clock controller: + - oscclk + - aclk_g3d_400 + + Input clocks for gscl clock controller: + - oscclk + - aclk_gscl_111 + - aclk_gscl_333 + + Input clocks for apollo clock controller: + - oscclk + - sclk_bus_pll_apollo + + Input clocks for atlas clock controller: + - oscclk + - sclk_bus_pll_atlas + + Input clocks for mscl clock controller: + - oscclk + - sclk_jpeg_mscl + - aclk_mscl_400 + + Input clocks for mfc clock controller: + - oscclk + - aclk_mfc_400 + + Input clocks for hevc clock controller: + - oscclk + - aclk_hevc_400 + + Input clocks for isp clock controller: + - oscclk + - aclk_isp_dis_400 + - aclk_isp_400 + + Input clocks for cam0 clock controller: + - oscclk + - aclk_cam0_333 + - aclk_cam0_400 + - aclk_cam0_552 + + Input clocks for cam1 clock controller: + - oscclk + - sclk_isp_uart_cam1 + - sclk_isp_spi1_cam1 + - sclk_isp_spi0_cam1 + - aclk_cam1_333 + - aclk_cam1_400 + - aclk_cam1_552 + +Optional properties: + - power-domains: a phandle to respective power domain node as described by + generic PM domain bindings (see power/power_domain.txt for more + information). + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5433.h header and can be used in device +tree sources. + +Example 1: Examples of 'oscclk' source clock node are listed below. + + xxti: xxti { + compatible = "fixed-clock"; + clock-output-names = "oscclk"; + #clock-cells = <0>; + }; + +Example 2: Examples of clock controller nodes are listed below. + + cmu_top: clock-controller@10030000 { + compatible = "samsung,exynos5433-cmu-top"; + reg = <0x10030000 0x0c04>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_mphy_pll", + "sclk_mfc_pll", + "sclk_bus_pll"; + clocks = <&xxti>, + <&cmu_cpif CLK_SCLK_MPHY_PLL>, + <&cmu_mif CLK_SCLK_MFC_PLL>, + <&cmu_mif CLK_SCLK_BUS_PLL>; + }; + + cmu_cpif: clock-controller@10fc0000 { + compatible = "samsung,exynos5433-cmu-cpif"; + reg = <0x10fc0000 0x0c04>; + #clock-cells = <1>; + + clock-names = "oscclk"; + clocks = <&xxti>; + }; + + cmu_mif: clock-controller@105b0000 { + compatible = "samsung,exynos5433-cmu-mif"; + reg = <0x105b0000 0x100c>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_mphy_pll"; + clocks = <&xxti>, + <&cmu_cpif CLK_SCLK_MPHY_PLL>; + }; + + cmu_peric: clock-controller@14c80000 { + compatible = "samsung,exynos5433-cmu-peric"; + reg = <0x14c80000 0x0b08>; + #clock-cells = <1>; + }; + + cmu_peris: clock-controller@10040000 { + compatible = "samsung,exynos5433-cmu-peris"; + reg = <0x10040000 0x0b20>; + #clock-cells = <1>; + }; + + cmu_fsys: clock-controller@156e0000 { + compatible = "samsung,exynos5433-cmu-fsys"; + reg = <0x156e0000 0x0b04>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_ufs_mphy", + "aclk_fsys_200", + "sclk_pcie_100_fsys", + "sclk_ufsunipro_fsys", + "sclk_mmc2_fsys", + "sclk_mmc1_fsys", + "sclk_mmc0_fsys", + "sclk_usbhost30_fsys", + "sclk_usbdrd30_fsys"; + clocks = <&xxti>, + <&cmu_cpif CLK_SCLK_UFS_MPHY>, + <&cmu_top CLK_ACLK_FSYS_200>, + <&cmu_top CLK_SCLK_PCIE_100_FSYS>, + <&cmu_top CLK_SCLK_UFSUNIPRO_FSYS>, + <&cmu_top CLK_SCLK_MMC2_FSYS>, + <&cmu_top CLK_SCLK_MMC1_FSYS>, + <&cmu_top CLK_SCLK_MMC0_FSYS>, + <&cmu_top CLK_SCLK_USBHOST30_FSYS>, + <&cmu_top CLK_SCLK_USBDRD30_FSYS>; + }; + + cmu_g2d: clock-controller@12460000 { + compatible = "samsung,exynos5433-cmu-g2d"; + reg = <0x12460000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_g2d_266", + "aclk_g2d_400"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_G2D_266>, + <&cmu_top CLK_ACLK_G2D_400>; + power-domains = <&pd_g2d>; + }; + + cmu_disp: clock-controller@13b90000 { + compatible = "samsung,exynos5433-cmu-disp"; + reg = <0x13b90000 0x0c04>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_dsim1_disp", + "sclk_dsim0_disp", + "sclk_dsd_disp", + "sclk_decon_tv_eclk_disp", + "sclk_decon_vclk_disp", + "sclk_decon_eclk_disp", + "sclk_decon_tv_vclk_disp", + "aclk_disp_333"; + clocks = <&xxti>, + <&cmu_mif CLK_SCLK_DSIM1_DISP>, + <&cmu_mif CLK_SCLK_DSIM0_DISP>, + <&cmu_mif CLK_SCLK_DSD_DISP>, + <&cmu_mif CLK_SCLK_DECON_TV_ECLK_DISP>, + <&cmu_mif CLK_SCLK_DECON_VCLK_DISP>, + <&cmu_mif CLK_SCLK_DECON_ECLK_DISP>, + <&cmu_mif CLK_SCLK_DECON_TV_VCLK_DISP>, + <&cmu_mif CLK_ACLK_DISP_333>; + power-domains = <&pd_disp>; + }; + + cmu_aud: clock-controller@114c0000 { + compatible = "samsung,exynos5433-cmu-aud"; + reg = <0x114c0000 0x0b04>; + #clock-cells = <1>; + + clock-names = "oscclk", "fout_aud_pll"; + clocks = <&xxti>, <&cmu_top CLK_FOUT_AUD_PLL>; + power-domains = <&pd_aud>; + }; + + cmu_bus0: clock-controller@13600000 { + compatible = "samsung,exynos5433-cmu-bus0"; + reg = <0x13600000 0x0b04>; + #clock-cells = <1>; + + clock-names = "aclk_bus0_400"; + clocks = <&cmu_top CLK_ACLK_BUS0_400>; + }; + + cmu_bus1: clock-controller@14800000 { + compatible = "samsung,exynos5433-cmu-bus1"; + reg = <0x14800000 0x0b04>; + #clock-cells = <1>; + + clock-names = "aclk_bus1_400"; + clocks = <&cmu_top CLK_ACLK_BUS1_400>; + }; + + cmu_bus2: clock-controller@13400000 { + compatible = "samsung,exynos5433-cmu-bus2"; + reg = <0x13400000 0x0b04>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_bus2_400"; + clocks = <&xxti>, <&cmu_mif CLK_ACLK_BUS2_400>; + }; + + cmu_g3d: clock-controller@14aa0000 { + compatible = "samsung,exynos5433-cmu-g3d"; + reg = <0x14aa0000 0x1000>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_g3d_400"; + clocks = <&xxti>, <&cmu_top CLK_ACLK_G3D_400>; + power-domains = <&pd_g3d>; + }; + + cmu_gscl: clock-controller@13cf0000 { + compatible = "samsung,exynos5433-cmu-gscl"; + reg = <0x13cf0000 0x0b10>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_gscl_111", + "aclk_gscl_333"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_GSCL_111>, + <&cmu_top CLK_ACLK_GSCL_333>; + power-domains = <&pd_gscl>; + }; + + cmu_apollo: clock-controller@11900000 { + compatible = "samsung,exynos5433-cmu-apollo"; + reg = <0x11900000 0x1088>; + #clock-cells = <1>; + + clock-names = "oscclk", "sclk_bus_pll_apollo"; + clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_APOLLO>; + }; + + cmu_atlas: clock-controller@11800000 { + compatible = "samsung,exynos5433-cmu-atlas"; + reg = <0x11800000 0x1088>; + #clock-cells = <1>; + + clock-names = "oscclk", "sclk_bus_pll_atlas"; + clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_ATLAS>; + }; + + cmu_mscl: clock-controller@105d0000 { + compatible = "samsung,exynos5433-cmu-mscl"; + reg = <0x105d0000 0x0b10>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_jpeg_mscl", + "aclk_mscl_400"; + clocks = <&xxti>, + <&cmu_top CLK_SCLK_JPEG_MSCL>, + <&cmu_top CLK_ACLK_MSCL_400>; + power-domains = <&pd_mscl>; + }; + + cmu_mfc: clock-controller@15280000 { + compatible = "samsung,exynos5433-cmu-mfc"; + reg = <0x15280000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_mfc_400"; + clocks = <&xxti>, <&cmu_top CLK_ACLK_MFC_400>; + power-domains = <&pd_mfc>; + }; + + cmu_hevc: clock-controller@14f80000 { + compatible = "samsung,exynos5433-cmu-hevc"; + reg = <0x14f80000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", "aclk_hevc_400"; + clocks = <&xxti>, <&cmu_top CLK_ACLK_HEVC_400>; + power-domains = <&pd_hevc>; + }; + + cmu_isp: clock-controller@146d0000 { + compatible = "samsung,exynos5433-cmu-isp"; + reg = <0x146d0000 0x0b0c>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_isp_dis_400", + "aclk_isp_400"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_ISP_DIS_400>, + <&cmu_top CLK_ACLK_ISP_400>; + power-domains = <&pd_isp>; + }; + + cmu_cam0: clock-controller@120d0000 { + compatible = "samsung,exynos5433-cmu-cam0"; + reg = <0x120d0000 0x0b0c>; + #clock-cells = <1>; + + clock-names = "oscclk", + "aclk_cam0_333", + "aclk_cam0_400", + "aclk_cam0_552"; + clocks = <&xxti>, + <&cmu_top CLK_ACLK_CAM0_333>, + <&cmu_top CLK_ACLK_CAM0_400>, + <&cmu_top CLK_ACLK_CAM0_552>; + power-domains = <&pd_cam0>; + }; + + cmu_cam1: clock-controller@145d0000 { + compatible = "samsung,exynos5433-cmu-cam1"; + reg = <0x145d0000 0x0b08>; + #clock-cells = <1>; + + clock-names = "oscclk", + "sclk_isp_uart_cam1", + "sclk_isp_spi1_cam1", + "sclk_isp_spi0_cam1", + "aclk_cam1_333", + "aclk_cam1_400", + "aclk_cam1_552"; + clocks = <&xxti>, + <&cmu_top CLK_SCLK_ISP_UART_CAM1>, + <&cmu_top CLK_SCLK_ISP_SPI1_CAM1>, + <&cmu_top CLK_SCLK_ISP_SPI0_CAM1>, + <&cmu_top CLK_ACLK_CAM1_333>, + <&cmu_top CLK_ACLK_CAM1_400>, + <&cmu_top CLK_ACLK_CAM1_552>; + power-domains = <&pd_cam1>; + }; + +Example 3: UART controller node that consumes the clock generated by the clock + controller. + + serial_0: serial@14c10000 { + compatible = "samsung,exynos5433-uart"; + reg = <0x14C10000 0x100>; + interrupts = <0 421 0>; + clocks = <&cmu_peric CLK_PCLK_UART0>, + <&cmu_peric CLK_SCLK_UART0>; + clock-names = "uart", "clk_uart_baud0"; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_bus>; + }; diff --git a/Documentation/devicetree/bindings/clock/exynos7-clock.txt b/Documentation/devicetree/bindings/clock/exynos7-clock.txt new file mode 100644 index 000000000..6bf1e7493 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/exynos7-clock.txt @@ -0,0 +1,108 @@ +* Samsung Exynos7 Clock Controller + +Exynos7 clock controller has various blocks which are instantiated +independently from the device-tree. These clock controllers +generate and supply clocks to various hardware blocks within +the SoC. + +Each clock is assigned an identifier and client nodes can use +this identifier to specify the clock which they consume. All +available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos7-clk.h header and can be used in +device tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It +is expected that they are defined using standard clock bindings +with following clock-output-names: + + - "fin_pll" - PLL input clock from XXTI + +Required Properties for Clock Controller: + + - compatible: clock controllers will use one of the following + compatible strings to indicate the clock controller + functionality. + + - "samsung,exynos7-clock-topc" + - "samsung,exynos7-clock-top0" + - "samsung,exynos7-clock-top1" + - "samsung,exynos7-clock-ccore" + - "samsung,exynos7-clock-peric0" + - "samsung,exynos7-clock-peric1" + - "samsung,exynos7-clock-peris" + - "samsung,exynos7-clock-fsys0" + - "samsung,exynos7-clock-fsys1" + - "samsung,exynos7-clock-mscl" + - "samsung,exynos7-clock-aud" + + - reg: physical base address of the controller and the length of + memory mapped region. + + - #clock-cells: should be 1. + + - clocks: list of clock identifiers which are fed as the input to + the given clock controller. Please refer the next section to + find the input clocks for a given controller. + +- clock-names: list of names of clocks which are fed as the input + to the given clock controller. + +Input clocks for top0 clock controller: + - fin_pll + - dout_sclk_bus0_pll + - dout_sclk_bus1_pll + - dout_sclk_cc_pll + - dout_sclk_mfc_pll + - dout_sclk_aud_pll + +Input clocks for top1 clock controller: + - fin_pll + - dout_sclk_bus0_pll + - dout_sclk_bus1_pll + - dout_sclk_cc_pll + - dout_sclk_mfc_pll + +Input clocks for ccore clock controller: + - fin_pll + - dout_aclk_ccore_133 + +Input clocks for peric0 clock controller: + - fin_pll + - dout_aclk_peric0_66 + - sclk_uart0 + +Input clocks for peric1 clock controller: + - fin_pll + - dout_aclk_peric1_66 + - sclk_uart1 + - sclk_uart2 + - sclk_uart3 + - sclk_spi0 + - sclk_spi1 + - sclk_spi2 + - sclk_spi3 + - sclk_spi4 + - sclk_i2s1 + - sclk_pcm1 + - sclk_spdif + +Input clocks for peris clock controller: + - fin_pll + - dout_aclk_peris_66 + +Input clocks for fsys0 clock controller: + - fin_pll + - dout_aclk_fsys0_200 + - dout_sclk_mmc2 + +Input clocks for fsys1 clock controller: + - fin_pll + - dout_aclk_fsys1_200 + - dout_sclk_mmc0 + - dout_sclk_mmc1 + +Input clocks for aud clock controller: + - fin_pll + - fout_aud_pll diff --git a/Documentation/devicetree/bindings/clock/fixed-clock.txt b/Documentation/devicetree/bindings/clock/fixed-clock.txt new file mode 100644 index 000000000..0641a663a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/fixed-clock.txt @@ -0,0 +1,23 @@ +Binding for simple fixed-rate clock sources. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "fixed-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- clock-frequency : frequency of clock in Hz. Should be a single cell. + +Optional properties: +- clock-accuracy : accuracy of clock in ppb (parts per billion). + Should be a single cell. +- clock-output-names : From common clock binding. + +Example: + clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000000>; + clock-accuracy = <100>; + }; diff --git a/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt b/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt new file mode 100644 index 000000000..189467a71 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/fixed-factor-clock.txt @@ -0,0 +1,28 @@ +Binding for simple fixed factor rate clock sources. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "fixed-factor-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- clock-div: fixed divider. +- clock-mult: fixed multiplier. +- clocks: parent clock. + +Optional properties: +- clock-output-names : From common clock binding. + +Some clocks that require special treatments are also handled by that +driver, with the compatibles: + - allwinner,sun4i-a10-pll3-2x-clk + +Example: + clock { + compatible = "fixed-factor-clock"; + clocks = <&parentclk>; + #clock-cells = <0>; + clock-div = <2>; + clock-mult = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/fujitsu,mb86s70-crg11.txt b/Documentation/devicetree/bindings/clock/fujitsu,mb86s70-crg11.txt new file mode 100644 index 000000000..332396265 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/fujitsu,mb86s70-crg11.txt @@ -0,0 +1,26 @@ +Fujitsu CRG11 clock driver bindings +----------------------------------- + +Required properties : +- compatible : Shall contain "fujitsu,mb86s70-crg11" +- #clock-cells : Shall be 3 {cntrlr domain port} + +The consumer specifies the desired clock pointing to its phandle. + +Example: + + clock: crg11 { + compatible = "fujitsu,mb86s70-crg11"; + #clock-cells = <3>; + }; + + mhu: mhu0@2b1f0000 { + #mbox-cells = <1>; + compatible = "arm,mhu"; + reg = <0 0x2B1F0000 0x1000>; + interrupts = <0 36 4>, /* LP Non-Sec */ + <0 35 4>, /* HP Non-Sec */ + <0 37 4>; /* Secure */ + clocks = <&clock 0 2 1>; /* Cntrlr:0 Domain:2 Port:1 */ + clock-names = "clk"; + }; diff --git a/Documentation/devicetree/bindings/clock/gpio-gate-clock.txt b/Documentation/devicetree/bindings/clock/gpio-gate-clock.txt new file mode 100644 index 000000000..d3379ff9b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/gpio-gate-clock.txt @@ -0,0 +1,21 @@ +Binding for simple gpio gated clock. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "gpio-gate-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- enable-gpios : GPIO reference for enabling and disabling the clock. + +Optional properties: +- clocks: Maximum of one parent clock is supported. + +Example: + clock { + compatible = "gpio-gate-clock"; + clocks = <&parentclk>; + #clock-cells = <0>; + enable-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/clock/gpio-mux-clock.txt b/Documentation/devicetree/bindings/clock/gpio-mux-clock.txt new file mode 100644 index 000000000..2be1e038c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/gpio-mux-clock.txt @@ -0,0 +1,19 @@ +Binding for simple gpio clock multiplexer. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "gpio-mux-clock". +- clocks: list of two references to parent clocks. +- #clock-cells : from common clock binding; shall be set to 0. +- select-gpios : GPIO reference for selecting the parent clock. + +Example: + clock { + compatible = "gpio-mux-clock"; + clocks = <&parentclk1>, <&parentclk2>; + #clock-cells = <0>; + select-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/clock/hi3620-clock.txt b/Documentation/devicetree/bindings/clock/hi3620-clock.txt new file mode 100644 index 000000000..dad6269f5 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hi3620-clock.txt @@ -0,0 +1,20 @@ +* Hisilicon Hi3620 Clock Controller + +The Hi3620 clock controller generates and supplies clock to various +controllers within the Hi3620 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "hisilicon,hi3620-clock" - controller compatible with Hi3620 SoC. + - "hisilicon,hi3620-mmc-clock" - controller specific for Hi3620 mmc. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/hi3620-clock.h>. diff --git a/Documentation/devicetree/bindings/clock/hi3660-clock.txt b/Documentation/devicetree/bindings/clock/hi3660-clock.txt new file mode 100644 index 000000000..946da7cee --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hi3660-clock.txt @@ -0,0 +1,47 @@ +* Hisilicon Hi3660 Clock Controller + +The Hi3660 clock controller generates and supplies clock to various +controllers within the Hi3660 SoC. + +Required Properties: + +- compatible: the compatible should be one of the following strings to + indicate the clock controller functionality. + + - "hisilicon,hi3660-crgctrl" + - "hisilicon,hi3660-pctrl" + - "hisilicon,hi3660-pmuctrl" + - "hisilicon,hi3660-sctrl" + - "hisilicon,hi3660-iomcu" + - "hisilicon,hi3660-stub-clk" + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Optional Properties: + +- mboxes: Phandle to the mailbox for sending message to MCU. + (See: ../mailbox/hisilicon,hi3660-mailbox.txt for more info) + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/hi3660-clock.h>. + +Examples: + crg_ctrl: clock-controller@fff35000 { + compatible = "hisilicon,hi3660-crgctrl", "syscon"; + reg = <0x0 0xfff35000 0x0 0x1000>; + #clock-cells = <1>; + }; + + uart0: serial@fdf02000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0 0xfdf02000 0x0 0x1000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg_ctrl HI3660_CLK_MUX_UART0>, + <&crg_ctrl HI3660_PCLK>; + clock-names = "uartclk", "apb_pclk"; + }; diff --git a/Documentation/devicetree/bindings/clock/hi6220-clock.txt b/Documentation/devicetree/bindings/clock/hi6220-clock.txt new file mode 100644 index 000000000..ef3deb7b8 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hi6220-clock.txt @@ -0,0 +1,52 @@ +* Hisilicon Hi6220 Clock Controller + +Clock control registers reside in different Hi6220 system controllers, +please refer the following document to know more about the binding rules +for these system controllers: + +Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt + +Required Properties: + +- compatible: the compatible should be one of the following strings to + indicate the clock controller functionality. + + - "hisilicon,hi6220-acpu-sctrl" + - "hisilicon,hi6220-aoctrl" + - "hisilicon,hi6220-sysctrl" + - "hisilicon,hi6220-mediactrl" + - "hisilicon,hi6220-pmctrl" + - "hisilicon,hi6220-stub-clk" + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Optional Properties: + +- hisilicon,hi6220-clk-sram: phandle to the syscon managing the SoC internal sram; + the driver need use the sram to pass parameters for frequency change. + +- mboxes: use the label reference for the mailbox as the first parameter, the + second parameter is the channel number. + +Example 1: + sys_ctrl: sys_ctrl@f7030000 { + compatible = "hisilicon,hi6220-sysctrl", "syscon"; + reg = <0x0 0xf7030000 0x0 0x2000>; + #clock-cells = <1>; + }; + +Example 2: + stub_clock: stub_clock { + compatible = "hisilicon,hi6220-stub-clk"; + hisilicon,hi6220-clk-sram = <&sram>; + #clock-cells = <1>; + mboxes = <&mailbox 1>; + }; + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/hi6220-clock.h>. diff --git a/Documentation/devicetree/bindings/clock/hisi-crg.txt b/Documentation/devicetree/bindings/clock/hisi-crg.txt new file mode 100644 index 000000000..cc60b3d42 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hisi-crg.txt @@ -0,0 +1,50 @@ +* HiSilicon Clock and Reset Generator(CRG) + +The CRG module provides clock and reset signals to various +modules within the SoC. + +This binding uses the following bindings: + Documentation/devicetree/bindings/clock/clock-bindings.txt + Documentation/devicetree/bindings/reset/reset.txt + +Required Properties: + +- compatible: should be one of the following. + - "hisilicon,hi3516cv300-crg" + - "hisilicon,hi3516cv300-sysctrl" + - "hisilicon,hi3519-crg" + - "hisilicon,hi3798cv200-crg" + - "hisilicon,hi3798cv200-sysctrl" + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/hi3519-clock.h>. + +- #reset-cells: should be 2. + +A reset signal can be controlled by writing a bit register in the CRG module. +The reset specifier consists of two cells. The first cell represents the +register offset relative to the base address. The second cell represents the +bit index in the register. + +Example: CRG nodes +CRG: clock-reset-controller@12010000 { + compatible = "hisilicon,hi3519-crg"; + reg = <0x12010000 0x10000>; + #clock-cells = <1>; + #reset-cells = <2>; +}; + +Example: consumer nodes +i2c0: i2c@12110000 { + compatible = "hisilicon,hi3519-i2c"; + reg = <0x12110000 0x1000>; + clocks = <&CRG HI3519_I2C0_RST>; + resets = <&CRG 0xe4 0>; +}; diff --git a/Documentation/devicetree/bindings/clock/hix5hd2-clock.txt b/Documentation/devicetree/bindings/clock/hix5hd2-clock.txt new file mode 100644 index 000000000..4733e58e4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/hix5hd2-clock.txt @@ -0,0 +1,30 @@ +* Hisilicon Hix5hd2 Clock Controller + +The hix5hd2 clock controller generates and supplies clock to various +controllers within the hix5hd2 SoC. + +Required Properties: + +- compatible: should be "hisilicon,hix5hd2-clock" +- reg: Address and length of the register set +- #clock-cells: Should be <1> + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/hix5hd2-clock.h>. + +Examples: + clock: clock@f8a22000 { + compatible = "hisilicon,hix5hd2-clock"; + reg = <0xf8a22000 0x1000>; + #clock-cells = <1>; + }; + + uart0: uart@f8b00000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0xf8b00000 0x1000>; + interrupts = <0 49 4>; + clocks = <&clock HIX5HD2_FIXED_83M>; + clock-names = "apb_pclk"; + }; diff --git a/Documentation/devicetree/bindings/clock/idt,versaclock5.txt b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt new file mode 100644 index 000000000..05a245c9d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/idt,versaclock5.txt @@ -0,0 +1,91 @@ +Binding for IDT VersaClock 5,6 programmable i2c clock generators. + +The IDT VersaClock 5 and VersaClock 6 are programmable i2c clock +generators providing from 3 to 12 output clocks. + +==I2C device node== + +Required properties: +- compatible: shall be one of + "idt,5p49v5923" + "idt,5p49v5925" + "idt,5p49v5933" + "idt,5p49v5935" + "idt,5p49v6901" +- reg: i2c device address, shall be 0x68 or 0x6a. +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: from common clock binding; list of parent clock handles, + - 5p49v5923 and + 5p49v5925 and + 5p49v6901: (required) either or both of XTAL or CLKIN + reference clock. + - 5p49v5933 and + - 5p49v5935: (optional) property not present (internal + Xtal used) or CLKIN reference + clock. +- clock-names: from common clock binding; clock input names, can be + - 5p49v5923 and + 5p49v5925 and + 5p49v6901: (required) either or both of "xin", "clkin". + - 5p49v5933 and + - 5p49v5935: (optional) property not present or "clkin". + +==Mapping between clock specifier and physical pins== + +When referencing the provided clock in the DT using phandle and +clock specifier, the following mapping applies: + +5P49V5923: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT2 + +5P49V5933: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT4 + +5P49V5925 and +5P49V5935: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT2 + 3 -- OUT3 + 4 -- OUT4 + +5P49V6901: + 0 -- OUT0_SEL_I2CB + 1 -- OUT1 + 2 -- OUT2 + 3 -- OUT3 + 4 -- OUT4 + +==Example== + +/* 25MHz reference crystal */ +ref25: ref25m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; +}; + +i2c-master-node { + + /* IDT 5P49V5923 i2c clock generator */ + vc5: clock-generator@6a { + compatible = "idt,5p49v5923"; + reg = <0x6a>; + #clock-cells = <1>; + + /* Connect XIN input to 25MHz reference */ + clocks = <&ref25m>; + clock-names = "xin"; + }; +}; + +/* Consumer referencing the 5P49V5923 pin OUT1 */ +consumer { + ... + clocks = <&vc5 1>; + ... +} diff --git a/Documentation/devicetree/bindings/clock/img,boston-clock.txt b/Documentation/devicetree/bindings/clock/img,boston-clock.txt new file mode 100644 index 000000000..7bc5e9ffb --- /dev/null +++ b/Documentation/devicetree/bindings/clock/img,boston-clock.txt @@ -0,0 +1,31 @@ +Binding for Imagination Technologies MIPS Boston clock sources. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +The device node must be a child node of the syscon node corresponding to the +Boston system's platform registers. + +Required properties: +- compatible : Should be "img,boston-clock". +- #clock-cells : Should be set to 1. + Values available for clock consumers can be found in the header file: + <dt-bindings/clock/boston-clock.h> + +Example: + + system-controller@17ffd000 { + compatible = "img,boston-platform-regs", "syscon"; + reg = <0x17ffd000 0x1000>; + + clk_boston: clock { + compatible = "img,boston-clock"; + #clock-cells = <1>; + }; + }; + + uart0: uart@17ffe000 { + /* ... */ + clocks = <&clk_boston BOSTON_CLK_SYS>; + }; diff --git a/Documentation/devicetree/bindings/clock/imx1-clock.txt b/Documentation/devicetree/bindings/clock/imx1-clock.txt new file mode 100644 index 000000000..9823baf7a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx1-clock.txt @@ -0,0 +1,26 @@ +* Clock bindings for Freescale i.MX1 CPUs + +Required properties: +- compatible: Should be "fsl,imx1-ccm". +- reg: Address and length of the register set. +- #clock-cells: Should be <1>. + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx1-clock.h +for the full list of i.MX1 clock IDs. + +Examples: + clks: ccm@21b000 { + #clock-cells = <1>; + compatible = "fsl,imx1-ccm"; + reg = <0x0021b000 0x1000>; + }; + + pwm: pwm@208000 { + #pwm-cells = <2>; + compatible = "fsl,imx1-pwm"; + reg = <0x00208000 0x1000>; + interrupts = <34>; + clocks = <&clks IMX1_CLK_DUMMY>, <&clks IMX1_CLK_PER1>; + clock-names = "ipg", "per"; + }; diff --git a/Documentation/devicetree/bindings/clock/imx21-clock.txt b/Documentation/devicetree/bindings/clock/imx21-clock.txt new file mode 100644 index 000000000..806f63d62 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx21-clock.txt @@ -0,0 +1,27 @@ +* Clock bindings for Freescale i.MX21 + +Required properties: +- compatible : Should be "fsl,imx21-ccm". +- reg : Address and length of the register set. +- interrupts : Should contain CCM interrupt. +- #clock-cells: Should be <1>. + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx21-clock.h +for the full list of i.MX21 clock IDs. + +Examples: + clks: ccm@10027000{ + compatible = "fsl,imx21-ccm"; + reg = <0x10027000 0x800>; + #clock-cells = <1>; + }; + + uart1: serial@1000a000 { + compatible = "fsl,imx21-uart"; + reg = <0x1000a000 0x1000>; + interrupts = <20>; + clocks = <&clks IMX21_CLK_UART1_IPG_GATE>, + <&clks IMX21_CLK_PER1>; + clock-names = "ipg", "per"; + }; diff --git a/Documentation/devicetree/bindings/clock/imx23-clock.txt b/Documentation/devicetree/bindings/clock/imx23-clock.txt new file mode 100644 index 000000000..8385348d3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx23-clock.txt @@ -0,0 +1,70 @@ +* Clock bindings for Freescale i.MX23 + +Required properties: +- compatible: Should be "fsl,imx23-clkctrl" +- reg: Address and length of the register set +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX23 +clocks and IDs. + + Clock ID + ------------------ + ref_xtal 0 + pll 1 + ref_cpu 2 + ref_emi 3 + ref_pix 4 + ref_io 5 + saif_sel 6 + lcdif_sel 7 + gpmi_sel 8 + ssp_sel 9 + emi_sel 10 + cpu 11 + etm_sel 12 + cpu_pll 13 + cpu_xtal 14 + hbus 15 + xbus 16 + lcdif_div 17 + ssp_div 18 + gpmi_div 19 + emi_pll 20 + emi_xtal 21 + etm_div 22 + saif_div 23 + clk32k_div 24 + rtc 25 + adc 26 + spdif_div 27 + clk32k 28 + dri 29 + pwm 30 + filt 31 + uart 32 + ssp 33 + gpmi 34 + spdif 35 + emi 36 + saif 37 + lcdif 38 + etm 39 + usb 40 + usb_phy 41 + +Examples: + +clks: clkctrl@80040000 { + compatible = "fsl,imx23-clkctrl"; + reg = <0x80040000 0x2000>; + #clock-cells = <1>; +}; + +auart0: serial@8006c000 { + compatible = "fsl,imx23-auart"; + reg = <0x8006c000 0x2000>; + interrupts = <24 25 23>; + clocks = <&clks 32>; +}; diff --git a/Documentation/devicetree/bindings/clock/imx25-clock.txt b/Documentation/devicetree/bindings/clock/imx25-clock.txt new file mode 100644 index 000000000..f8135ea9c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx25-clock.txt @@ -0,0 +1,160 @@ +* Clock bindings for Freescale i.MX25 + +Required properties: +- compatible: Should be "fsl,imx25-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX25 +clocks and IDs. + + Clock ID + --------------------------- + dummy 0 + osc 1 + mpll 2 + upll 3 + mpll_cpu_3_4 4 + cpu_sel 5 + cpu 6 + ahb 7 + usb_div 8 + ipg 9 + per0_sel 10 + per1_sel 11 + per2_sel 12 + per3_sel 13 + per4_sel 14 + per5_sel 15 + per6_sel 16 + per7_sel 17 + per8_sel 18 + per9_sel 19 + per10_sel 20 + per11_sel 21 + per12_sel 22 + per13_sel 23 + per14_sel 24 + per15_sel 25 + per0 26 + per1 27 + per2 28 + per3 29 + per4 30 + per5 31 + per6 32 + per7 33 + per8 34 + per9 35 + per10 36 + per11 37 + per12 38 + per13 39 + per14 40 + per15 41 + csi_ipg_per 42 + epit_ipg_per 43 + esai_ipg_per 44 + esdhc1_ipg_per 45 + esdhc2_ipg_per 46 + gpt_ipg_per 47 + i2c_ipg_per 48 + lcdc_ipg_per 49 + nfc_ipg_per 50 + owire_ipg_per 51 + pwm_ipg_per 52 + sim1_ipg_per 53 + sim2_ipg_per 54 + ssi1_ipg_per 55 + ssi2_ipg_per 56 + uart_ipg_per 57 + ata_ahb 58 + reserved 59 + csi_ahb 60 + emi_ahb 61 + esai_ahb 62 + esdhc1_ahb 63 + esdhc2_ahb 64 + fec_ahb 65 + lcdc_ahb 66 + rtic_ahb 67 + sdma_ahb 68 + slcdc_ahb 69 + usbotg_ahb 70 + reserved 71 + reserved 72 + reserved 73 + reserved 74 + can1_ipg 75 + can2_ipg 76 + csi_ipg 77 + cspi1_ipg 78 + cspi2_ipg 79 + cspi3_ipg 80 + dryice_ipg 81 + ect_ipg 82 + epit1_ipg 83 + epit2_ipg 84 + reserved 85 + esdhc1_ipg 86 + esdhc2_ipg 87 + fec_ipg 88 + reserved 89 + reserved 90 + reserved 91 + gpt1_ipg 92 + gpt2_ipg 93 + gpt3_ipg 94 + gpt4_ipg 95 + reserved 96 + reserved 97 + reserved 98 + iim_ipg 99 + reserved 100 + reserved 101 + kpp_ipg 102 + lcdc_ipg 103 + reserved 104 + pwm1_ipg 105 + pwm2_ipg 106 + pwm3_ipg 107 + pwm4_ipg 108 + rngb_ipg 109 + reserved 110 + scc_ipg 111 + sdma_ipg 112 + sim1_ipg 113 + sim2_ipg 114 + slcdc_ipg 115 + spba_ipg 116 + ssi1_ipg 117 + ssi2_ipg 118 + tsc_ipg 119 + uart1_ipg 120 + uart2_ipg 121 + uart3_ipg 122 + uart4_ipg 123 + uart5_ipg 124 + reserved 125 + wdt_ipg 126 + cko_div 127 + cko_sel 128 + cko 129 + +Examples: + +clks: ccm@53f80000 { + compatible = "fsl,imx25-ccm"; + reg = <0x53f80000 0x4000>; + interrupts = <31>; +}; + +uart1: serial@43f90000 { + compatible = "fsl,imx25-uart", "fsl,imx21-uart"; + reg = <0x43f90000 0x4000>; + interrupts = <45>; + clocks = <&clks 79>, <&clks 50>; + clock-names = "ipg", "per"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx27-clock.txt b/Documentation/devicetree/bindings/clock/imx27-clock.txt new file mode 100644 index 000000000..4c95c048d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx27-clock.txt @@ -0,0 +1,27 @@ +* Clock bindings for Freescale i.MX27 + +Required properties: +- compatible: Should be "fsl,imx27-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx27-clock.h +for the full list of i.MX27 clock IDs. + +Examples: + clks: ccm@10027000{ + compatible = "fsl,imx27-ccm"; + reg = <0x10027000 0x1000>; + #clock-cells = <1>; + }; + + uart1: serial@1000a000 { + compatible = "fsl,imx27-uart", "fsl,imx21-uart"; + reg = <0x1000a000 0x1000>; + interrupts = <20>; + clocks = <&clks IMX27_CLK_UART1_IPG_GATE>, + <&clks IMX27_CLK_PER1_GATE>; + clock-names = "ipg", "per"; + }; diff --git a/Documentation/devicetree/bindings/clock/imx28-clock.txt b/Documentation/devicetree/bindings/clock/imx28-clock.txt new file mode 100644 index 000000000..d84a37d28 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx28-clock.txt @@ -0,0 +1,93 @@ +* Clock bindings for Freescale i.MX28 + +Required properties: +- compatible: Should be "fsl,imx28-clkctrl" +- reg: Address and length of the register set +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX28 +clocks and IDs. + + Clock ID + ------------------ + ref_xtal 0 + pll0 1 + pll1 2 + pll2 3 + ref_cpu 4 + ref_emi 5 + ref_io0 6 + ref_io1 7 + ref_pix 8 + ref_hsadc 9 + ref_gpmi 10 + saif0_sel 11 + saif1_sel 12 + gpmi_sel 13 + ssp0_sel 14 + ssp1_sel 15 + ssp2_sel 16 + ssp3_sel 17 + emi_sel 18 + etm_sel 19 + lcdif_sel 20 + cpu 21 + ptp_sel 22 + cpu_pll 23 + cpu_xtal 24 + hbus 25 + xbus 26 + ssp0_div 27 + ssp1_div 28 + ssp2_div 29 + ssp3_div 30 + gpmi_div 31 + emi_pll 32 + emi_xtal 33 + lcdif_div 34 + etm_div 35 + ptp 36 + saif0_div 37 + saif1_div 38 + clk32k_div 39 + rtc 40 + lradc 41 + spdif_div 42 + clk32k 43 + pwm 44 + uart 45 + ssp0 46 + ssp1 47 + ssp2 48 + ssp3 49 + gpmi 50 + spdif 51 + emi 52 + saif0 53 + saif1 54 + lcdif 55 + etm 56 + fec 57 + can0 58 + can1 59 + usb0 60 + usb1 61 + usb0_phy 62 + usb1_phy 63 + enet_out 64 + +Examples: + +clks: clkctrl@80040000 { + compatible = "fsl,imx28-clkctrl"; + reg = <0x80040000 0x2000>; + #clock-cells = <1>; +}; + +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + interrupts = <112 70 71>; + clocks = <&clks 45>; +}; diff --git a/Documentation/devicetree/bindings/clock/imx31-clock.txt b/Documentation/devicetree/bindings/clock/imx31-clock.txt new file mode 100644 index 000000000..0a291090e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx31-clock.txt @@ -0,0 +1,90 @@ +* Clock bindings for Freescale i.MX31 + +Required properties: +- compatible: Should be "fsl,imx31-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX31 +clocks and IDs. + + Clock ID + ----------------------- + dummy 0 + ckih 1 + ckil 2 + mpll 3 + spll 4 + upll 5 + mcu_main 6 + hsp 7 + ahb 8 + nfc 9 + ipg 10 + per_div 11 + per 12 + csi_sel 13 + fir_sel 14 + csi_div 15 + usb_div_pre 16 + usb_div_post 17 + fir_div_pre 18 + fir_div_post 19 + sdhc1_gate 20 + sdhc2_gate 21 + gpt_gate 22 + epit1_gate 23 + epit2_gate 24 + iim_gate 25 + ata_gate 26 + sdma_gate 27 + cspi3_gate 28 + rng_gate 29 + uart1_gate 30 + uart2_gate 31 + ssi1_gate 32 + i2c1_gate 33 + i2c2_gate 34 + i2c3_gate 35 + hantro_gate 36 + mstick1_gate 37 + mstick2_gate 38 + csi_gate 39 + rtc_gate 40 + wdog_gate 41 + pwm_gate 42 + sim_gate 43 + ect_gate 44 + usb_gate 45 + kpp_gate 46 + ipu_gate 47 + uart3_gate 48 + uart4_gate 49 + uart5_gate 50 + owire_gate 51 + ssi2_gate 52 + cspi1_gate 53 + cspi2_gate 54 + gacc_gate 55 + emi_gate 56 + rtic_gate 57 + firi_gate 58 + +Examples: + +clks: ccm@53f80000{ + compatible = "fsl,imx31-ccm"; + reg = <0x53f80000 0x4000>; + interrupts = <31>, <53>; + #clock-cells = <1>; +}; + +uart1: serial@43f90000 { + compatible = "fsl,imx31-uart", "fsl,imx21-uart"; + reg = <0x43f90000 0x4000>; + interrupts = <45>; + clocks = <&clks 10>, <&clks 30>; + clock-names = "ipg", "per"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx35-clock.txt b/Documentation/devicetree/bindings/clock/imx35-clock.txt new file mode 100644 index 000000000..f49783213 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx35-clock.txt @@ -0,0 +1,114 @@ +* Clock bindings for Freescale i.MX35 + +Required properties: +- compatible: Should be "fsl,imx35-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of i.MX35 +clocks and IDs. + + Clock ID + --------------------------- + ckih 0 + mpll 1 + ppll 2 + mpll_075 3 + arm 4 + hsp 5 + hsp_div 6 + hsp_sel 7 + ahb 8 + ipg 9 + arm_per_div 10 + ahb_per_div 11 + ipg_per 12 + uart_sel 13 + uart_div 14 + esdhc_sel 15 + esdhc1_div 16 + esdhc2_div 17 + esdhc3_div 18 + spdif_sel 19 + spdif_div_pre 20 + spdif_div_post 21 + ssi_sel 22 + ssi1_div_pre 23 + ssi1_div_post 24 + ssi2_div_pre 25 + ssi2_div_post 26 + usb_sel 27 + usb_div 28 + nfc_div 29 + asrc_gate 30 + pata_gate 31 + audmux_gate 32 + can1_gate 33 + can2_gate 34 + cspi1_gate 35 + cspi2_gate 36 + ect_gate 37 + edio_gate 38 + emi_gate 39 + epit1_gate 40 + epit2_gate 41 + esai_gate 42 + esdhc1_gate 43 + esdhc2_gate 44 + esdhc3_gate 45 + fec_gate 46 + gpio1_gate 47 + gpio2_gate 48 + gpio3_gate 49 + gpt_gate 50 + i2c1_gate 51 + i2c2_gate 52 + i2c3_gate 53 + iomuxc_gate 54 + ipu_gate 55 + kpp_gate 56 + mlb_gate 57 + mshc_gate 58 + owire_gate 59 + pwm_gate 60 + rngc_gate 61 + rtc_gate 62 + rtic_gate 63 + scc_gate 64 + sdma_gate 65 + spba_gate 66 + spdif_gate 67 + ssi1_gate 68 + ssi2_gate 69 + uart1_gate 70 + uart2_gate 71 + uart3_gate 72 + usbotg_gate 73 + wdog_gate 74 + max_gate 75 + admux_gate 76 + csi_gate 77 + csi_div 78 + csi_sel 79 + iim_gate 80 + gpu2d_gate 81 + ckli_gate 82 + +Examples: + +clks: ccm@53f80000 { + compatible = "fsl,imx35-ccm"; + reg = <0x53f80000 0x4000>; + interrupts = <31>; + #clock-cells = <1>; +}; + +esdhc1: esdhc@53fb4000 { + compatible = "fsl,imx35-esdhc"; + reg = <0x53fb4000 0x4000>; + interrupts = <7>; + clocks = <&clks 9>, <&clks 8>, <&clks 43>; + clock-names = "ipg", "ahb", "per"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx5-clock.txt b/Documentation/devicetree/bindings/clock/imx5-clock.txt new file mode 100644 index 000000000..a24ca9e58 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx5-clock.txt @@ -0,0 +1,28 @@ +* Clock bindings for Freescale i.MX5 + +Required properties: +- compatible: Should be "fsl,<soc>-ccm" , where <soc> can be imx51 or imx53 +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx5-clock.h +for the full list of i.MX5 clock IDs. + +Examples (for mx53): + +clks: ccm@53fd4000{ + compatible = "fsl,imx53-ccm"; + reg = <0x53fd4000 0x4000>; + interrupts = <0 71 0x04 0 72 0x04>; + #clock-cells = <1>; +}; + +can1: can@53fc8000 { + compatible = "fsl,imx53-flexcan", "fsl,p1010-flexcan"; + reg = <0x53fc8000 0x4000>; + interrupts = <82>; + clocks = <&clks IMX5_CLK_CAN1_IPG_GATE>, <&clks IMX5_CLK_CAN1_SERIAL_GATE>; + clock-names = "ipg", "per"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt new file mode 100644 index 000000000..a45ca67a9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt @@ -0,0 +1,30 @@ +* Clock bindings for Freescale i.MX6 Quad + +Required properties: +- compatible: Should be "fsl,imx6q-ccm" +- reg: Address and length of the register set +- interrupts: Should contain CCM interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6qdl-clock.h +for the full list of i.MX6 Quad and DualLite clock IDs. + +Examples: + +#include <dt-bindings/clock/imx6qdl-clock.h> + +clks: ccm@20c4000 { + compatible = "fsl,imx6q-ccm"; + reg = <0x020c4000 0x4000>; + interrupts = <0 87 0x04 0 88 0x04>; + #clock-cells = <1>; +}; + +uart1: serial@2020000 { + compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; + reg = <0x02020000 0x4000>; + interrupts = <0 26 0x04>; + clocks = <&clks IMX6QDL_CLK_UART_IPG>, <&clks IMX6QDL_CLK_UART_SERIAL>; + clock-names = "ipg", "per"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx6sl-clock.txt b/Documentation/devicetree/bindings/clock/imx6sl-clock.txt new file mode 100644 index 000000000..15e40bdf1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6sl-clock.txt @@ -0,0 +1,10 @@ +* Clock bindings for Freescale i.MX6 SoloLite + +Required properties: +- compatible: Should be "fsl,imx6sl-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6sl-clock.h +for the full list of i.MX6 SoloLite clock IDs. diff --git a/Documentation/devicetree/bindings/clock/imx6sll-clock.txt b/Documentation/devicetree/bindings/clock/imx6sll-clock.txt new file mode 100644 index 000000000..fee849d5f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6sll-clock.txt @@ -0,0 +1,36 @@ +* Clock bindings for Freescale i.MX6 SLL + +Required properties: +- compatible: Should be "fsl,imx6sll-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6sll-clock.h +for the full list of i.MX6 SLL clock IDs. + +Examples: + +#include <dt-bindings/clock/imx6sll-clock.h> + +clks: clock-controller@20c4000 { + compatible = "fsl,imx6sll-ccm"; + reg = <0x020c4000 0x4000>; + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; + #clock-cells = <1>; + clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>; + clock-names = "ckil", "osc", "ipp_di0", "ipp_di1"; +}; + +uart1: serial@2020000 { + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; + reg = <0x02020000 0x4000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6SLL_CLK_UART1_IPG>, + <&clks IMX6SLL_CLK_UART1_SERIAL>; + clock-names = "ipg", "per"; +}; diff --git a/Documentation/devicetree/bindings/clock/imx6sx-clock.txt b/Documentation/devicetree/bindings/clock/imx6sx-clock.txt new file mode 100644 index 000000000..22362b9b7 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6sx-clock.txt @@ -0,0 +1,13 @@ +* Clock bindings for Freescale i.MX6 SoloX + +Required properties: +- compatible: Should be "fsl,imx6sx-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6sx-clock.h +for the full list of i.MX6 SoloX clock IDs. diff --git a/Documentation/devicetree/bindings/clock/imx6ul-clock.txt b/Documentation/devicetree/bindings/clock/imx6ul-clock.txt new file mode 100644 index 000000000..571d5039f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6ul-clock.txt @@ -0,0 +1,13 @@ +* Clock bindings for Freescale i.MX6 UltraLite + +Required properties: +- compatible: Should be "fsl,imx6ul-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6ul-clock.h +for the full list of i.MX6 UltraLite clock IDs. diff --git a/Documentation/devicetree/bindings/clock/imx7d-clock.txt b/Documentation/devicetree/bindings/clock/imx7d-clock.txt new file mode 100644 index 000000000..9d3026d81 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx7d-clock.txt @@ -0,0 +1,13 @@ +* Clock bindings for Freescale i.MX7 Dual + +Required properties: +- compatible: Should be "fsl,imx7d-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx7d-clock.h +for the full list of i.MX7 Dual clock IDs. diff --git a/Documentation/devicetree/bindings/clock/ingenic,cgu.txt b/Documentation/devicetree/bindings/clock/ingenic,cgu.txt new file mode 100644 index 000000000..f8d4134ae --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ingenic,cgu.txt @@ -0,0 +1,53 @@ +Ingenic SoC CGU binding + +The CGU in an Ingenic SoC provides all the clocks generated on-chip. It +typically includes a variety of PLLs, multiplexers, dividers & gates in order +to provide many different clock signals derived from only 2 external source +clocks. + +Required properties: +- compatible : Should be "ingenic,<soctype>-cgu". + For example "ingenic,jz4740-cgu" or "ingenic,jz4780-cgu". +- reg : The address & length of the CGU registers. +- clocks : List of phandle & clock specifiers for clocks external to the CGU. + Two such external clocks should be specified - first the external crystal + "ext" and second the RTC clock source "rtc". +- clock-names : List of name strings for the external clocks. +- #clock-cells: Should be 1. + Clock consumers specify this argument to identify a clock. The valid values + may be found in <dt-bindings/clock/<soctype>-cgu.h>. + +Example SoC include file: + +/ { + cgu: jz4740-cgu { + compatible = "ingenic,jz4740-cgu"; + reg = <0x10000000 0x100>; + #clock-cells = <1>; + }; + + uart0: serial@10030000 { + clocks = <&cgu JZ4740_CLK_UART0>; + }; +}; + +Example board file: + +/ { + ext: clock@0 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + + rtc: clock@1 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + + &cgu { + clocks = <&ext> <&rtc>; + clock-names: "ext", "rtc"; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/intc_stratix10.txt b/Documentation/devicetree/bindings/clock/intc_stratix10.txt new file mode 100644 index 000000000..9f4ec5cb5 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/intc_stratix10.txt @@ -0,0 +1,20 @@ +Device Tree Clock bindings for Intel's SoCFPGA Stratix10 platform + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be + "intel,stratix10-clkmgr" + +- reg : shall be the control register offset from CLOCK_MANAGER's base for the clock. + +- #clock-cells : from common clock binding, shall be set to 1. + +Example: + clkmgr: clock-controller@ffd10000 { + compatible = "intel,stratix10-clkmgr"; + reg = <0xffd10000 0x1000>; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/keystone-gate.txt b/Documentation/devicetree/bindings/clock/keystone-gate.txt new file mode 100644 index 000000000..c5aa18702 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/keystone-gate.txt @@ -0,0 +1,29 @@ +Status: Unstable - ABI compatibility may be broken in the future + +Binding for Keystone gate control driver which uses PSC controller IP. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,keystone,psc-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : parent clock phandle +- reg : psc control and domain address address space +- reg-names : psc control and domain registers +- domain-id : psc domain id needed to check the transition state register + +Optional properties: +- clock-output-names : From common clock binding to override the + default output clock name +Example: + clkusb: clkusb { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk16>; + clock-output-names = "usb"; + reg = <0x02350008 0xb00>, <0x02350000 0x400>; + reg-names = "control", "domain"; + domain-id = <0>; + }; diff --git a/Documentation/devicetree/bindings/clock/keystone-pll.txt b/Documentation/devicetree/bindings/clock/keystone-pll.txt new file mode 100644 index 000000000..47570d207 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/keystone-pll.txt @@ -0,0 +1,84 @@ +Status: Unstable - ABI compatibility may be broken in the future + +Binding for keystone PLLs. The main PLL IP typically has a multiplier, +a divider and a post divider. The additional PLL IPs like ARMPLL, DDRPLL +and PAPLL are controlled by the memory mapped register where as the Main +PLL is controlled by a PLL controller registers along with memory mapped +registers. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- #clock-cells : from common clock binding; shall be set to 0. +- compatible : shall be "ti,keystone,main-pll-clock" or "ti,keystone,pll-clock" +- clocks : parent clock phandle +- reg - pll control0 and pll multipler registers +- reg-names : control, multiplier and post-divider. The multiplier and + post-divider registers are applicable only for main pll clock +- fixed-postdiv : fixed post divider value. If absent, use clkod register bits + for postdiv + +Example: + mainpllclk: mainpllclk@2310110 { + #clock-cells = <0>; + compatible = "ti,keystone,main-pll-clock"; + clocks = <&refclksys>; + reg = <0x02620350 4>, <0x02310110 4>, <0x02310108 4>; + reg-names = "control", "multiplier", "post-divider"; + fixed-postdiv = <2>; + }; + + papllclk: papllclk@2620358 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-clock"; + clocks = <&refclkpass>; + clock-output-names = "pa-pll-clk"; + reg = <0x02620358 4>; + reg-names = "control"; + }; + +Required properties: +- #clock-cells : from common clock binding; shall be set to 0. +- compatible : shall be "ti,keystone,pll-mux-clock" +- clocks : link phandles of parent clocks +- reg - pll mux register +- bit-shift : number of bits to shift the bit-mask +- bit-mask : arbitrary bitmask for programming the mux + +Optional properties: +- clock-output-names : From common clock binding. + +Example: + mainmuxclk: mainmuxclk@2310108 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-mux-clock"; + clocks = <&mainpllclk>, <&refclkmain>; + reg = <0x02310108 4>; + bit-shift = <23>; + bit-mask = <1>; + clock-output-names = "mainmuxclk"; + }; + +Required properties: +- #clock-cells : from common clock binding; shall be set to 0. +- compatible : shall be "ti,keystone,pll-divider-clock" +- clocks : parent clock phandle +- reg - pll mux register +- bit-shift : number of bits to shift the bit-mask +- bit-mask : arbitrary bitmask for programming the divider + +Optional properties: +- clock-output-names : From common clock binding. + +Example: + gemtraceclk: gemtraceclk@2310120 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-divider-clock"; + clocks = <&mainmuxclk>; + reg = <0x02310120 4>; + bit-shift = <0>; + bit-mask = <8>; + clock-output-names = "gemtraceclk"; + }; diff --git a/Documentation/devicetree/bindings/clock/lpc1850-ccu.txt b/Documentation/devicetree/bindings/clock/lpc1850-ccu.txt new file mode 100644 index 000000000..fa97c1201 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/lpc1850-ccu.txt @@ -0,0 +1,77 @@ +* NXP LPC1850 Clock Control Unit (CCU) + +Each CGU base clock has several clock branches which can be turned on +or off independently by the Clock Control Units CCU1 or CCU2. The +branch clocks are distributed between CCU1 and CCU2. + + - Above text taken from NXP LPC1850 User Manual. + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: + Should be "nxp,lpc1850-ccu" +- reg: + Shall define the base and range of the address space + containing clock control registers +- #clock-cells: + Shall have value <1>. The permitted clock-specifier values + are the branch clock names defined in table below. +- clocks: + Shall contain a list of phandles for the base clocks routed + from the CGU to the specific CCU. See mapping of base clocks + and CCU in table below. +- clock-names: + Shall contain a list of names for the base clock routed + from the CGU to the specific CCU. Valid CCU clock names: + "base_usb0_clk", "base_periph_clk", "base_usb1_clk", + "base_cpu_clk", "base_spifi_clk", "base_spi_clk", + "base_apb1_clk", "base_apb3_clk", "base_adchs_clk", + "base_sdio_clk", "base_ssp0_clk", "base_ssp1_clk", + "base_uart0_clk", "base_uart1_clk", "base_uart2_clk", + "base_uart3_clk", "base_audio_clk" + +Which branch clocks that are available on the CCU depends on the +specific LPC part. Check the user manual for your specific part. + +A list of CCU clocks can be found in dt-bindings/clock/lpc18xx-ccu.h. + +Example board file: + +soc { + ccu1: clock-controller@40051000 { + compatible = "nxp,lpc1850-ccu"; + reg = <0x40051000 0x1000>; + #clock-cells = <1>; + clocks = <&cgu BASE_APB3_CLK>, <&cgu BASE_APB1_CLK>, + <&cgu BASE_SPIFI_CLK>, <&cgu BASE_CPU_CLK>, + <&cgu BASE_PERIPH_CLK>, <&cgu BASE_USB0_CLK>, + <&cgu BASE_USB1_CLK>, <&cgu BASE_SPI_CLK>; + clock-names = "base_apb3_clk", "base_apb1_clk", + "base_spifi_clk", "base_cpu_clk", + "base_periph_clk", "base_usb0_clk", + "base_usb1_clk", "base_spi_clk"; + }; + + ccu2: clock-controller@40052000 { + compatible = "nxp,lpc1850-ccu"; + reg = <0x40052000 0x1000>; + #clock-cells = <1>; + clocks = <&cgu BASE_AUDIO_CLK>, <&cgu BASE_UART3_CLK>, + <&cgu BASE_UART2_CLK>, <&cgu BASE_UART1_CLK>, + <&cgu BASE_UART0_CLK>, <&cgu BASE_SSP1_CLK>, + <&cgu BASE_SSP0_CLK>, <&cgu BASE_SDIO_CLK>; + clock-names = "base_audio_clk", "base_uart3_clk", + "base_uart2_clk", "base_uart1_clk", + "base_uart0_clk", "base_ssp1_clk", + "base_ssp0_clk", "base_sdio_clk"; + }; + + /* A user of CCU brach clocks */ + uart1: serial@40082000 { + ... + clocks = <&ccu2 CLK_APB0_UART1>, <&ccu1 CLK_CPU_UART1>; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/clock/lpc1850-cgu.txt b/Documentation/devicetree/bindings/clock/lpc1850-cgu.txt new file mode 100644 index 000000000..2cc32a9a9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/lpc1850-cgu.txt @@ -0,0 +1,131 @@ +* NXP LPC1850 Clock Generation Unit (CGU) + +The CGU generates multiple independent clocks for the core and the +peripheral blocks of the LPC18xx. Each independent clock is called +a base clock and itself is one of the inputs to the two Clock +Control Units (CCUs) which control the branch clocks to the +individual peripherals. + +The CGU selects the inputs to the clock generators from multiple +clock sources, controls the clock generation, and routes the outputs +of the clock generators through the clock source bus to the output +stages. Each output stage provides an independent clock source and +corresponds to one of the base clocks for the LPC18xx. + + - Above text taken from NXP LPC1850 User Manual. + + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: + Should be "nxp,lpc1850-cgu" +- reg: + Shall define the base and range of the address space + containing clock control registers +- #clock-cells: + Shall have value <1>. The permitted clock-specifier values + are the base clock numbers defined below. +- clocks: + Shall contain a list of phandles for the external input + sources to the CGU. The list shall be in the following + order: xtal, 32khz, enet_rx_clk, enet_tx_clk, gp_clkin. +- clock-indices: + Shall be an ordered list of numbers defining the base clock + number provided by the CGU. +- clock-output-names: + Shall be an ordered list of strings defining the names of + the clocks provided by the CGU. + +Which base clocks that are available on the CGU depends on the +specific LPC part. Base clocks are numbered from 0 to 27. + +Number: Name: Description: + 0 BASE_SAFE_CLK Base safe clock (always on) for WWDT + 1 BASE_USB0_CLK Base clock for USB0 + 2 BASE_PERIPH_CLK Base clock for Cortex-M0SUB subsystem, + SPI, and SGPIO + 3 BASE_USB1_CLK Base clock for USB1 + 4 BASE_CPU_CLK System base clock for ARM Cortex-M core + and APB peripheral blocks #0 and #2 + 5 BASE_SPIFI_CLK Base clock for SPIFI + 6 BASE_SPI_CLK Base clock for SPI + 7 BASE_PHY_RX_CLK Base clock for Ethernet PHY Receive clock + 8 BASE_PHY_TX_CLK Base clock for Ethernet PHY Transmit clock + 9 BASE_APB1_CLK Base clock for APB peripheral block # 1 +10 BASE_APB3_CLK Base clock for APB peripheral block # 3 +11 BASE_LCD_CLK Base clock for LCD +12 BASE_ADCHS_CLK Base clock for ADCHS +13 BASE_SDIO_CLK Base clock for SD/MMC +14 BASE_SSP0_CLK Base clock for SSP0 +15 BASE_SSP1_CLK Base clock for SSP1 +16 BASE_UART0_CLK Base clock for UART0 +17 BASE_UART1_CLK Base clock for UART1 +18 BASE_UART2_CLK Base clock for UART2 +19 BASE_UART3_CLK Base clock for UART3 +20 BASE_OUT_CLK Base clock for CLKOUT pin +24-21 - Reserved +25 BASE_AUDIO_CLK Base clock for audio system (I2S) +26 BASE_CGU_OUT0_CLK Base clock for CGU_OUT0 clock output +27 BASE_CGU_OUT1_CLK Base clock for CGU_OUT1 clock output + +BASE_PERIPH_CLK and BASE_SPI_CLK is only available on LPC43xx. +BASE_ADCHS_CLK is only available on LPC4370. + + +Example board file: + +/ { + clocks { + xtal: xtal { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + + xtal32: xtal32 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + + enet_rx_clk: enet_rx_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "enet_rx_clk"; + }; + + enet_tx_clk: enet_tx_clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "enet_tx_clk"; + }; + + gp_clkin: gp_clkin { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + clock-output-names = "gp_clkin"; + }; + }; + + soc { + cgu: clock-controller@40050000 { + compatible = "nxp,lpc1850-cgu"; + reg = <0x40050000 0x1000>; + #clock-cells = <1>; + clocks = <&xtal>, <&creg_clk 1>, <&enet_rx_clk>, <&enet_tx_clk>, <&gp_clkin>; + }; + + /* A CGU and CCU clock consumer */ + lcdc: lcdc@40008000 { + ... + clocks = <&cgu BASE_LCD_CLK>, <&ccu1 CLK_CPU_LCD>; + clock-names = "clcdclk", "apb_pclk"; + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/lpc1850-creg-clk.txt b/Documentation/devicetree/bindings/clock/lpc1850-creg-clk.txt new file mode 100644 index 000000000..6f1c7b4e4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/lpc1850-creg-clk.txt @@ -0,0 +1,52 @@ +* NXP LPC1850 CREG clocks + +The NXP LPC18xx/43xx CREG (Configuration Registers) block contains +control registers for two low speed clocks. One of the clocks is a +32 kHz oscillator driver with power up/down and clock gating. Next +is a fixed divider that creates a 1 kHz clock from the 32 kHz osc. + +These clocks are used by the RTC and the Event Router peripherials. +The 32 kHz can also be routed to other peripherials to enable low +power modes. + +This binding uses the common clock binding: + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: + Should be "nxp,lpc1850-creg-clk" +- #clock-cells: + Shall have value <1>. +- clocks: + Shall contain a phandle to the fixed 32 kHz crystal. + +The creg-clk node must be a child of the creg syscon node. + +The following clocks are available from the clock node. + +Clock ID Name + 0 1 kHz clock + 1 32 kHz Oscillator + +Example: +soc { + creg: syscon@40043000 { + compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd"; + reg = <0x40043000 0x1000>; + + creg_clk: clock-controller { + compatible = "nxp,lpc1850-creg-clk"; + clocks = <&xtal32>; + #clock-cells = <1>; + }; + + ... + }; + + rtc: rtc@40046000 { + ... + clocks = <&creg_clk 0>, <&ccu1 CLK_CPU_BUS>; + clock-names = "rtc", "reg"; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/clock/lsi,axm5516-clks.txt b/Documentation/devicetree/bindings/clock/lsi,axm5516-clks.txt new file mode 100644 index 000000000..3ce97cfe9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/lsi,axm5516-clks.txt @@ -0,0 +1,29 @@ +AXM5516 clock driver bindings +----------------------------- + +Required properties : +- compatible : shall contain "lsi,axm5516-clks" +- reg : shall contain base register location and length +- #clock-cells : shall contain 1 + +The consumer specifies the desired clock by having the clock ID in its "clocks" +phandle cell. See <dt-bindings/clock/lsi,axxia-clock.h> for the list of +supported clock IDs. + +Example: + + clks: clock-controller@2010020000 { + compatible = "lsi,axm5516-clks"; + #clock-cells = <1>; + reg = <0x20 0x10020000 0 0x20000>; + }; + + serial0: uart@2010080000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x20 0x10080000 0 0x1000>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks AXXIA_CLK_PER>; + clock-names = "apb_pclk"; + }; + }; + diff --git a/Documentation/devicetree/bindings/clock/marvell,berlin.txt b/Documentation/devicetree/bindings/clock/marvell,berlin.txt new file mode 100644 index 000000000..c611c495f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/marvell,berlin.txt @@ -0,0 +1,31 @@ +Device Tree Clock bindings for Marvell Berlin + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Clock related registers are spread among the chip control registers. Berlin +clock node should be a sub-node of the chip controller node. Marvell Berlin2 +(BG2, BG2CD, BG2Q) SoCs share the same IP for PLLs and clocks, with some +minor differences in features and register layout. + +Required properties: +- compatible: must be "marvell,berlin2-clk" or "marvell,berlin2q-clk" +- #clock-cells: must be 1 +- clocks: must be the input parent clock phandle +- clock-names: name of the input parent clock + Allowed clock-names for the reference clocks are + "refclk" for the SoCs oscillator input on all SoCs, + and SoC-specific input clocks for + BG2/BG2CD: "video_ext0" for the external video clock input + + +Example: + +chip_clk: clock { + compatible = "marvell,berlin2q-clk"; + + #clock-cells = <1>; + clocks = <&refclk>; + clock-names = "refclk"; +}; diff --git a/Documentation/devicetree/bindings/clock/marvell,mmp2.txt b/Documentation/devicetree/bindings/clock/marvell,mmp2.txt new file mode 100644 index 000000000..af376a01f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/marvell,mmp2.txt @@ -0,0 +1,21 @@ +* Marvell MMP2 Clock Controller + +The MMP2 clock subsystem generates and supplies clock to various +controllers within the MMP2 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "marvell,mmp2-clock" - controller compatible with MMP2 SoC. + +- reg: physical base address of the clock subsystem and length of memory mapped + region. There are 3 places in SOC has clock control logic: + "mpmu", "apmu", "apbc". So three reg spaces need to be defined. + +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/marvell-mmp2.h>. diff --git a/Documentation/devicetree/bindings/clock/marvell,pxa168.txt b/Documentation/devicetree/bindings/clock/marvell,pxa168.txt new file mode 100644 index 000000000..c62eb1d17 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/marvell,pxa168.txt @@ -0,0 +1,21 @@ +* Marvell PXA168 Clock Controller + +The PXA168 clock subsystem generates and supplies clock to various +controllers within the PXA168 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "marvell,pxa168-clock" - controller compatible with PXA168 SoC. + +- reg: physical base address of the clock subsystem and length of memory mapped + region. There are 3 places in SOC has clock control logic: + "mpmu", "apmu", "apbc". So three reg spaces need to be defined. + +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/marvell,pxa168.h>. diff --git a/Documentation/devicetree/bindings/clock/marvell,pxa1928.txt b/Documentation/devicetree/bindings/clock/marvell,pxa1928.txt new file mode 100644 index 000000000..809c5a2d8 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/marvell,pxa1928.txt @@ -0,0 +1,21 @@ +* Marvell PXA1928 Clock Controllers + +The PXA1928 clock subsystem generates and supplies clock to various +controllers within the PXA1928 SoC. The PXA1928 contains 3 clock controller +blocks called APMU, MPMU, and APBC roughly corresponding to internal buses. + +Required Properties: + +- compatible: should be one of the following. + - "marvell,pxa1928-apmu" - APMU controller compatible + - "marvell,pxa1928-mpmu" - MPMU controller compatible + - "marvell,pxa1928-apbc" - APBC controller compatible +- reg: physical base address of the clock controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Each clock is assigned an identifier and client nodes use the clock controller +phandle and this identifier to specify the clock which they consume. + +All these identifiers can be found in <dt-bindings/clock/marvell,pxa1928.h>. diff --git a/Documentation/devicetree/bindings/clock/marvell,pxa910.txt b/Documentation/devicetree/bindings/clock/marvell,pxa910.txt new file mode 100644 index 000000000..d9f41f3c0 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/marvell,pxa910.txt @@ -0,0 +1,21 @@ +* Marvell PXA910 Clock Controller + +The PXA910 clock subsystem generates and supplies clock to various +controllers within the PXA910 SoC. + +Required Properties: + +- compatible: should be one of the following. + - "marvell,pxa910-clock" - controller compatible with PXA910 SoC. + +- reg: physical base address of the clock subsystem and length of memory mapped + region. There are 4 places in SOC has clock control logic: + "mpmu", "apmu", "apbc", "apbcp". So four reg spaces need to be defined. + +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + +All these identifier could be found in <dt-bindings/clock/marvell-pxa910.h>. diff --git a/Documentation/devicetree/bindings/clock/maxim,max77686.txt b/Documentation/devicetree/bindings/clock/maxim,max77686.txt new file mode 100644 index 000000000..3472b461c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/maxim,max77686.txt @@ -0,0 +1,114 @@ +Binding for Maxim MAX77686/MAX77802/MAX77620 32k clock generator block + +This is a part of device tree bindings of MAX77686/MAX77802/MAX77620 +multi-function device. More information can be found in MFD DT binding +doc as follows: + bindings/mfd/max77686.txt for MAX77686 and + bindings/mfd/max77802.txt for MAX77802 and + bindings/mfd/max77620.txt for MAX77620. + +The MAX77686 contains three 32.768khz clock outputs that can be controlled +(gated/ungated) over I2C. Clocks are defined as preprocessor macros in +dt-bindings/clock/maxim,max77686.h. + + +The MAX77802 contains two 32.768khz clock outputs that can be controlled +(gated/ungated) over I2C. Clocks are defined as preprocessor macros in +dt-bindings/clock/maxim,max77802.h. + +The MAX77686 contains one 32.768khz clock outputs that can be controlled +(gated/ungated) over I2C. Clocks are defined as preprocessor macros in +dt-bindings/clock/maxim,max77620.h. + +Following properties should be presend in main device node of the MFD chip. + +Required properties: + +- #clock-cells: from common clock binding; shall be set to 1. + +Optional properties: +- clock-output-names: From common clock binding. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Following indices are allowed: + - 0: 32khz_ap clock (max77686, max77802), 32khz_out0 (max77620) + - 1: 32khz_cp clock (max77686, max77802), + - 2: 32khz_pmic clock (max77686). + +Clocks are defined as preprocessor macros in above dt-binding header for +respective chips. + +Example: + +1. With MAX77686: + +#include <dt-bindings/clock/maxim,max77686.h> +/* ... */ + + Node of the MFD chip + max77686: max77686@9 { + compatible = "maxim,max77686"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #clock-cells = <1>; + + /* ... */ + }; + + Clock consumer node + + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77686 MAX77686_CLK_PMIC>; + }; + +2. With MAX77802: + +#include <dt-bindings/clock/maxim,max77802.h> +/* ... */ + + Node of the MFD chip + max77802: max77802@9 { + compatible = "maxim,max77802"; + interrupt-parent = <&wakeup_eint>; + interrupts = <26 0>; + reg = <0x09>; + #clock-cells = <1>; + + /* ... */ + }; + + Clock consumer node + + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77802 MAX77802_CLK_32K_AP>; + }; + + +3. With MAX77620: + +#include <dt-bindings/clock/maxim,max77620.h> +/* ... */ + + Node of the MFD chip + max77620: max77620@3c { + compatible = "maxim,max77620"; + reg = <0x3c>; + #clock-cells = <1>; + /* ... */ + }; + + Clock consumer node + + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "my-clock"; + clocks = <&max77620 MAX77620_CLK_32K_OUT0>; + }; diff --git a/Documentation/devicetree/bindings/clock/maxim,max9485.txt b/Documentation/devicetree/bindings/clock/maxim,max9485.txt new file mode 100644 index 000000000..61bec1100 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/maxim,max9485.txt @@ -0,0 +1,59 @@ +Devicetree bindings for Maxim MAX9485 Programmable Audio Clock Generator + +This device exposes 4 clocks in total: + +- MAX9485_MCLKOUT: A gated, buffered output of the input clock of 27 MHz +- MAX9485_CLKOUT: A PLL that can be configured to 16 different discrete + frequencies +- MAX9485_CLKOUT[1,2]: Two gated outputs for MAX9485_CLKOUT + +MAX9485_CLKOUT[1,2] are children of MAX9485_CLKOUT which upchain all rate set +requests. + +Required properties: +- compatible: "maxim,max9485" +- clocks: Input clock, must provice 27.000 MHz +- clock-names: Must be set to "xclk" +- #clock-cells: From common clock binding; shall be set to 1 + +Optional properties: +- reset-gpios: GPIO descriptor connected to the #RESET input pin +- vdd-supply: A regulator node for Vdd +- clock-output-names: Name of output clocks, as defined in common clock + bindings + +If not explicitly set, the output names are "mclkout", "clkout", "clkout1" +and "clkout2". + +Clocks are defined as preprocessor macros in the dt-binding header. + +Example: + + #include <dt-bindings/clock/maxim,max9485.h> + + xo-27mhz: xo-27mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; + + &i2c0 { + max9485: audio-clock@63 { + reg = <0x63>; + compatible = "maxim,max9485"; + clock-names = "xclk"; + clocks = <&xo-27mhz>; + reset-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + vdd-supply = <&3v3-reg>; + #clock-cells = <1>; + }; + }; + + // Clock consumer node + + foo@0 { + compatible = "bar,foo"; + /* ... */ + clock-names = "foo-input-clk"; + clocks = <&max9485 MAX9485_CLKOUT1>; + }; diff --git a/Documentation/devicetree/bindings/clock/microchip,pic32.txt b/Documentation/devicetree/bindings/clock/microchip,pic32.txt new file mode 100644 index 000000000..c93d88fdd --- /dev/null +++ b/Documentation/devicetree/bindings/clock/microchip,pic32.txt @@ -0,0 +1,39 @@ +Microchip PIC32 Clock Controller Binding +---------------------------------------- +Microchip clock controller is consists of few oscillators, PLL, multiplexer +and few divider modules. + +This binding uses common clock bindings. +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: shall be "microchip,pic32mzda-clk". +- reg: shall contain base address and length of clock registers. +- #clock-cells: shall be 1. + +Optional properties: +- microchip,pic32mzda-sosc: shall be added only if platform has + secondary oscillator connected. + +Example: + rootclk: clock-controller@1f801200 { + compatible = "microchip,pic32mzda-clk"; + reg = <0x1f801200 0x200>; + #clock-cells = <1>; + /* optional */ + microchip,pic32mzda-sosc; + }; + + +The clock consumer shall specify the desired clock-output of the clock +controller (as defined in [2]) by specifying output-id in its "clock" +phandle cell. +[2] include/dt-bindings/clock/microchip,pic32-clock.h + +For example for UART2: +uart2: serial@2 { + compatible = "microchip,pic32mzda-uart"; + reg = <>; + interrupts = <>; + clocks = <&rootclk PB2CLK>; +}; diff --git a/Documentation/devicetree/bindings/clock/moxa,moxart-clock.txt b/Documentation/devicetree/bindings/clock/moxa,moxart-clock.txt new file mode 100644 index 000000000..fedea8431 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/moxa,moxart-clock.txt @@ -0,0 +1,48 @@ +Device Tree Clock bindings for arch-moxart + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +MOXA ART SoCs allow to determine PLL output and APB frequencies +by reading registers holding multiplier and divisor information. + + +PLL: + +Required properties: +- compatible : Must be "moxa,moxart-pll-clock" +- #clock-cells : Should be 0 +- reg : Should contain registers location and length +- clocks : Should contain phandle + clock-specifier for the parent clock + +Optional properties: +- clock-output-names : Should contain clock name + + +APB: + +Required properties: +- compatible : Must be "moxa,moxart-apb-clock" +- #clock-cells : Should be 0 +- reg : Should contain registers location and length +- clocks : Should contain phandle + clock-specifier for the parent clock + +Optional properties: +- clock-output-names : Should contain clock name + + +For example: + + clk_pll: clk_pll@98100000 { + compatible = "moxa,moxart-pll-clock"; + #clock-cells = <0>; + reg = <0x98100000 0x34>; + }; + + clk_apb: clk_apb@98100000 { + compatible = "moxa,moxart-apb-clock"; + #clock-cells = <0>; + reg = <0x98100000 0x34>; + clocks = <&clk_pll>; + }; diff --git a/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt new file mode 100644 index 000000000..796c260c1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-core-clock.txt @@ -0,0 +1,86 @@ +* Core Clock bindings for Marvell MVEBU SoCs + +Marvell MVEBU SoCs usually allow to determine core clock frequencies by +reading the Sample-At-Reset (SAR) register. The core clock consumer should +specify the desired clock by having the clock ID in its "clocks" phandle cell. + +The following is a list of provided IDs and clock names on Armada 370/XP: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = nbclk (L2 Cache clock) + 3 = hclk (DRAM control clock) + 4 = dramclk (DDR clock) + +The following is a list of provided IDs and clock names on Armada 375: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = l2clk (L2 Cache clock) + 3 = ddrclk (DDR clock) + +The following is a list of provided IDs and clock names on Armada 380/385: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = l2clk (L2 Cache clock) + 3 = ddrclk (DDR clock) + +The following is a list of provided IDs and clock names on Armada 39x: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = nbclk (Coherent Fabric clock) + 3 = hclk (SDRAM Controller Internal Clock) + 4 = dclk (SDRAM Interface Clock) + 5 = refclk (Reference Clock) + +The following is a list of provided IDs and clock names on 98dx3236: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU clock) + 2 = ddrclk (DDR clock) + 3 = mpll (MPLL Clock) + +The following is a list of provided IDs and clock names on Kirkwood and Dove: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU0 clock) + 2 = l2clk (L2 Cache clock derived from CPU0 clock) + 3 = ddrclk (DDR controller clock derived from CPU0 clock) + +The following is a list of provided IDs and clock names on Orion5x: + 0 = tclk (Internal Bus clock) + 1 = cpuclk (CPU0 clock) + 2 = ddrclk (DDR controller clock derived from CPU0 clock) + +Required properties: +- compatible : shall be one of the following: + "marvell,armada-370-core-clock" - For Armada 370 SoC core clocks + "marvell,armada-375-core-clock" - For Armada 375 SoC core clocks + "marvell,armada-380-core-clock" - For Armada 380/385 SoC core clocks + "marvell,armada-390-core-clock" - For Armada 39x SoC core clocks + "marvell,armada-xp-core-clock" - For Armada XP SoC core clocks + "marvell,mv98dx3236-core-clock" - For 98dx3236 family SoC core clocks + "marvell,dove-core-clock" - for Dove SoC core clocks + "marvell,kirkwood-core-clock" - for Kirkwood SoC (except mv88f6180) + "marvell,mv88f6180-core-clock" - for Kirkwood MV88f6180 SoC + "marvell,mv88f5181-core-clock" - for Orion MV88F5181 SoC + "marvell,mv88f5182-core-clock" - for Orion MV88F5182 SoC + "marvell,mv88f5281-core-clock" - for Orion MV88F5281 SoC + "marvell,mv88f6183-core-clock" - for Orion MV88F6183 SoC +- reg : shall be the register address of the Sample-At-Reset (SAR) register +- #clock-cells : from common clock binding; shall be set to 1 + +Optional properties: +- clock-output-names : from common clock binding; allows overwrite default clock + output names ("tclk", "cpuclk", "l2clk", "ddrclk") + +Example: + +core_clk: core-clocks@d0214 { + compatible = "marvell,dove-core-clock"; + reg = <0xd0214 0x4>; + #clock-cells = <1>; +}; + +spi0: spi@10600 { + compatible = "marvell,orion-spi"; + /* ... */ + /* get tclk from core clock provider */ + clocks = <&core_clk 0>; +}; diff --git a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt new file mode 100644 index 000000000..c7b4e3a6b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt @@ -0,0 +1,23 @@ +* Core Divider Clock bindings for Marvell MVEBU SoCs + +The following is a list of provided IDs and clock names on Armada 370/XP: + 0 = nand (NAND clock) + +Required properties: +- compatible : must be "marvell,armada-370-corediv-clock", + "marvell,armada-375-corediv-clock", + "marvell,armada-380-corediv-clock", + "marvell,mv98dx3236-corediv-clock", + +- reg : must be the register address of Core Divider control register +- #clock-cells : from common clock binding; shall be set to 1 +- clocks : must be set to the parent's phandle + +Example: + +corediv_clk: corediv-clocks@18740 { + compatible = "marvell,armada-370-corediv-clock"; + reg = <0x18740 0xc>; + #clock-cells = <1>; + clocks = <&pll>; +}; diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt new file mode 100644 index 000000000..7f28506ea --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt @@ -0,0 +1,23 @@ +Device Tree Clock bindings for cpu clock of Marvell EBU platforms + +Required properties: +- compatible : shall be one of the following: + "marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP + "marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC +- reg : Address and length of the clock complex register set, followed + by address and length of the PMU DFS registers +- #clock-cells : should be set to 1. +- clocks : shall be the input parent clock phandle for the clock. + +cpuclk: clock-complex@d0018700 { + #clock-cells = <1>; + compatible = "marvell,armada-xp-cpu-clock"; + reg = <0xd0018700 0xA0>, <0x1c054 0x10>; + clocks = <&coreclk 1>; +} + +cpu@0 { + compatible = "marvell,sheeva-v7"; + reg = <0>; + clocks = <&cpuclk 0>; +}; diff --git a/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt new file mode 100644 index 000000000..de562da2a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/mvebu-gated-clock.txt @@ -0,0 +1,205 @@ +* Gated Clock bindings for Marvell EBU SoCs + +Marvell Armada 370/375/380/385/39x/XP, Dove and Kirkwood allow some +peripheral clocks to be gated to save some power. The clock consumer +should specify the desired clock by having the clock ID in its +"clocks" phandle cell. The clock ID is directly mapped to the +corresponding clock gating control bit in HW to ease manual clock +lookup in datasheet. + +The following is a list of provided IDs for Armada 370: +ID Clock Peripheral +----------------------------------- +0 Audio AC97 Cntrl +1 pex0_en PCIe 0 Clock out +2 pex1_en PCIe 1 Clock out +3 ge1 Gigabit Ethernet 1 +4 ge0 Gigabit Ethernet 0 +5 pex0 PCIe Cntrl 0 +9 pex1 PCIe Cntrl 1 +15 sata0 SATA Host 0 +17 sdio SDHCI Host +23 crypto CESA (crypto engine) +25 tdm Time Division Mplx +28 ddr DDR Cntrl +30 sata1 SATA Host 0 + +The following is a list of provided IDs for Armada 375: +ID Clock Peripheral +----------------------------------- +2 mu Management Unit +3 pp Packet Processor +4 ptp PTP +5 pex0 PCIe 0 Clock out +6 pex1 PCIe 1 Clock out +8 audio Audio Cntrl +11 nd_clk Nand Flash Cntrl +14 sata0_link SATA 0 Link +15 sata0_core SATA 0 Core +16 usb3 USB3 Host +17 sdio SDHCI Host +18 usb USB Host +19 gop Gigabit Ethernet MAC +20 sata1_link SATA 1 Link +21 sata1_core SATA 1 Core +22 xor0 XOR DMA 0 +23 xor1 XOR DMA 0 +24 copro Coprocessor +25 tdm Time Division Mplx +28 crypto0_enc Cryptographic Unit Port 0 Encryption +29 crypto0_core Cryptographic Unit Port 0 Core +30 crypto1_enc Cryptographic Unit Port 1 Encryption +31 crypto1_core Cryptographic Unit Port 1 Core + +The following is a list of provided IDs for Armada 380/385: +ID Clock Peripheral +----------------------------------- +0 audio Audio +2 ge2 Gigabit Ethernet 2 +3 ge1 Gigabit Ethernet 1 +4 ge0 Gigabit Ethernet 0 +5 pex1 PCIe 1 +6 pex2 PCIe 2 +7 pex3 PCIe 3 +8 pex0 PCIe 0 +9 usb3h0 USB3 Host 0 +10 usb3h1 USB3 Host 1 +11 usb3d USB3 Device +13 bm Buffer Management +14 crypto0z Cryptographic 0 Z +15 sata0 SATA 0 +16 crypto1z Cryptographic 1 Z +17 sdio SDIO +18 usb2 USB 2 +21 crypto1 Cryptographic 1 +22 xor0 XOR 0 +23 crypto0 Cryptographic 0 +25 tdm Time Division Multiplexing +28 xor1 XOR 1 +30 sata1 SATA 1 + +The following is a list of provided IDs for Armada 39x: +ID Clock Peripheral +----------------------------------- +5 pex1 PCIe 1 +6 pex2 PCIe 2 +7 pex3 PCIe 3 +8 pex0 PCIe 0 +9 usb3h0 USB3 Host 0 +10 usb3h1 USB3 Host 1 +15 sata0 SATA 0 +17 sdio SDIO +22 xor0 XOR 0 +28 xor1 XOR 1 + +The following is a list of provided IDs for Armada XP: +ID Clock Peripheral +----------------------------------- +0 audio Audio Cntrl +1 ge3 Gigabit Ethernet 3 +2 ge2 Gigabit Ethernet 2 +3 ge1 Gigabit Ethernet 1 +4 ge0 Gigabit Ethernet 0 +5 pex0 PCIe Cntrl 0 +6 pex1 PCIe Cntrl 1 +7 pex2 PCIe Cntrl 2 +8 pex3 PCIe Cntrl 3 +13 bp +14 sata0lnk +15 sata0 SATA Host 0 +16 lcd LCD Cntrl +17 sdio SDHCI Host +18 usb0 USB Host 0 +19 usb1 USB Host 1 +20 usb2 USB Host 2 +22 xor0 XOR DMA 0 +23 crypto CESA engine +25 tdm Time Division Mplx +28 xor1 XOR DMA 1 +29 sata1lnk +30 sata1 SATA Host 1 + +The following is a list of provided IDs for 98dx3236: +ID Clock Peripheral +----------------------------------- +3 ge1 Gigabit Ethernet 1 +4 ge0 Gigabit Ethernet 0 +5 pex0 PCIe Cntrl 0 +17 sdio SDHCI Host +18 usb0 USB Host 0 +22 xor0 XOR DMA 0 + +The following is a list of provided IDs for Dove: +ID Clock Peripheral +----------------------------------- +0 usb0 USB Host 0 +1 usb1 USB Host 1 +2 ge Gigabit Ethernet +3 sata SATA Host +4 pex0 PCIe Cntrl 0 +5 pex1 PCIe Cntrl 1 +8 sdio0 SDHCI Host 0 +9 sdio1 SDHCI Host 1 +10 nand NAND Cntrl +11 camera Camera Cntrl +12 i2s0 I2S Cntrl 0 +13 i2s1 I2S Cntrl 1 +15 crypto CESA engine +21 ac97 AC97 Cntrl +22 pdma Peripheral DMA +23 xor0 XOR DMA 0 +24 xor1 XOR DMA 1 +30 gephy Gigabit Ethernel PHY +Note: gephy(30) is implemented as a parent clock of ge(2) + +The following is a list of provided IDs for Kirkwood: +ID Clock Peripheral +----------------------------------- +0 ge0 Gigabit Ethernet 0 +2 pex0 PCIe Cntrl 0 +3 usb0 USB Host 0 +4 sdio SDIO Cntrl +5 tsu Transp. Stream Unit +6 dunit SDRAM Cntrl +7 runit Runit +8 xor0 XOR DMA 0 +9 audio I2S Cntrl 0 +14 sata0 SATA Host 0 +15 sata1 SATA Host 1 +16 xor1 XOR DMA 1 +17 crypto CESA engine +18 pex1 PCIe Cntrl 1 +19 ge1 Gigabit Ethernet 1 +20 tdm Time Division Mplx + +Required properties: +- compatible : shall be one of the following: + "marvell,armada-370-gating-clock" - for Armada 370 SoC clock gating + "marvell,armada-375-gating-clock" - for Armada 375 SoC clock gating + "marvell,armada-380-gating-clock" - for Armada 380/385 SoC clock gating + "marvell,armada-390-gating-clock" - for Armada 39x SoC clock gating + "marvell,armada-xp-gating-clock" - for Armada XP SoC clock gating + "marvell,mv98dx3236-gating-clock" - for 98dx3236 SoC clock gating + "marvell,dove-gating-clock" - for Dove SoC clock gating + "marvell,kirkwood-gating-clock" - for Kirkwood SoC clock gating +- reg : shall be the register address of the Clock Gating Control register +- #clock-cells : from common clock binding; shall be set to 1 + +Optional properties: +- clocks : default parent clock phandle (e.g. tclk) + +Example: + +gate_clk: clock-gating-control@d0038 { + compatible = "marvell,dove-gating-clock"; + reg = <0xd0038 0x4>; + /* default parent clock is tclk */ + clocks = <&core_clk 0>; + #clock-cells = <1>; +}; + +sdio0: sdio@92000 { + compatible = "marvell,dove-sdhci"; + /* get clk gate bit 8 (sdio0) */ + clocks = <&gate_clk 8>; +}; diff --git a/Documentation/devicetree/bindings/clock/nspire-clock.txt b/Documentation/devicetree/bindings/clock/nspire-clock.txt new file mode 100644 index 000000000..7c3bc8bb5 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nspire-clock.txt @@ -0,0 +1,24 @@ +TI-NSPIRE Clocks + +Required properties: +- compatible: Valid compatible properties include: + "lsi,nspire-cx-ahb-divider" for the AHB divider in the CX model + "lsi,nspire-classic-ahb-divider" for the AHB divider in the older model + "lsi,nspire-cx-clock" for the base clock in the CX model + "lsi,nspire-classic-clock" for the base clock in the older model + +- reg: Physical base address of the controller and length of memory mapped + region. + +Optional: +- clocks: For the "nspire-*-ahb-divider" compatible clocks, this is the parent + clock where it divides the rate from. + +Example: + +ahb_clk { + #clock-cells = <0>; + compatible = "lsi,nspire-cx-clock"; + reg = <0x900B0000 0x4>; + clocks = <&base_clk>; +}; diff --git a/Documentation/devicetree/bindings/clock/nuvoton,npcm750-clk.txt b/Documentation/devicetree/bindings/clock/nuvoton,npcm750-clk.txt new file mode 100644 index 000000000..f82064546 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nuvoton,npcm750-clk.txt @@ -0,0 +1,100 @@ +* Nuvoton NPCM7XX Clock Controller + +Nuvoton Poleg BMC NPCM7XX contains an integrated clock controller, which +generates and supplies clocks to all modules within the BMC. + +External clocks: + +There are six fixed clocks that are generated outside the BMC. All clocks are of +a known fixed value that cannot be changed. clk_refclk, clk_mcbypck and +clk_sysbypck are inputs to the clock controller. +clk_rg1refck, clk_rg2refck and clk_xin are external clocks suppling the +network. They are set on the device tree, but not used by the clock module. The +network devices use them directly. +Example can be found below. + +All available clocks are defined as preprocessor macros in: +dt-bindings/clock/nuvoton,npcm7xx-clock.h +and can be reused as DT sources. + +Required Properties of clock controller: + + - compatible: "nuvoton,npcm750-clk" : for clock controller of Nuvoton + Poleg BMC NPCM750 + + - reg: physical base address of the clock controller and length of + memory mapped region. + + - #clock-cells: should be 1. + +Example: Clock controller node: + + clk: clock-controller@f0801000 { + compatible = "nuvoton,npcm750-clk"; + #clock-cells = <1>; + reg = <0xf0801000 0x1000>; + clock-names = "refclk", "sysbypck", "mcbypck"; + clocks = <&clk_refclk>, <&clk_sysbypck>, <&clk_mcbypck>; + }; + +Example: Required external clocks for network: + + /* external reference clock */ + clk_refclk: clk-refclk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + clock-output-names = "refclk"; + }; + + /* external reference clock for cpu. float in normal operation */ + clk_sysbypck: clk-sysbypck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <800000000>; + clock-output-names = "sysbypck"; + }; + + /* external reference clock for MC. float in normal operation */ + clk_mcbypck: clk-mcbypck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <800000000>; + clock-output-names = "mcbypck"; + }; + + /* external clock signal rg1refck, supplied by the phy */ + clk_rg1refck: clk-rg1refck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + clock-output-names = "clk_rg1refck"; + }; + + /* external clock signal rg2refck, supplied by the phy */ + clk_rg2refck: clk-rg2refck { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + clock-output-names = "clk_rg2refck"; + }; + + clk_xin: clk-xin { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + clock-output-names = "clk_xin"; + }; + + +Example: GMAC controller node that consumes two clocks: a generated clk by the +clock controller and a fixed clock from DT (clk_rg1refck). + + ethernet0: ethernet@f0802000 { + compatible = "snps,dwmac"; + reg = <0xf0802000 0x2000>; + interrupts = <0 14 4>; + interrupt-names = "macirq"; + clocks = <&clk_rg1refck>, <&clk NPCM7XX_CLK_AHB>; + clock-names = "stmmaceth", "clk_gmac"; + }; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt new file mode 100644 index 000000000..9acea9d93 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra114-car.txt @@ -0,0 +1,63 @@ +NVIDIA Tegra114 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra114-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in", and the board-specific oscillator "osc". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the + CAR. The assignments may be found in header file + <dt-bindings/clock/tegra114-car.h>. +- #reset-cells : Should be 1. + In clock consumers, this cell represents the bit number in the CAR's + array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. + +Example SoC include file: + +/ { + tegra_car: clock { + compatible = "nvidia,tegra114-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car TEGRA114_CLK_USB2>; + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + osc: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k> <&osc>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt new file mode 100644 index 000000000..7f02fb4ca --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-car.txt @@ -0,0 +1,107 @@ +NVIDIA Tegra124 and Tegra132 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra124-car" or "nvidia,tegra132-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in", and the board-specific oscillator "osc". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the + CAR. The assignments may be found in the header files + <dt-bindings/clock/tegra124-car-common.h> (which covers IDs common + to Tegra124 and Tegra132) and <dt-bindings/clock/tegra124-car.h> + (for Tegra124-specific clocks). +- #reset-cells : Should be 1. + In clock consumers, this cell represents the bit number in the CAR's + array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. +- nvidia,external-memory-controller : phandle of the EMC driver. + +The node should contain a "emc-timings" subnode for each supported RAM type (see +field RAM_CODE in register PMC_STRAPPING_OPT_A). + +Required properties for "emc-timings" nodes : +- nvidia,ram-code : Should contain the value of RAM_CODE this timing set + is used for. + +Each "emc-timings" node should contain a "timing" subnode for every supported +EMC clock rate. + +Required properties for "timing" nodes : +- clock-frequency : Should contain the memory clock rate to which this timing +relates. +- nvidia,parent-clock-frequency : Should contain the rate at which the current +parent of the EMC clock should be running at this timing. +- clocks : Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names : Must include the following entries: + - emc-parent : the clock that should be the parent of the EMC clock at this +timing. + +Example SoC include file: + +/ { + tegra_car: clock@60006000 { + compatible = "nvidia,tegra124-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + nvidia,external-memory-controller = <&emc>; + }; + + usb@c5004000 { + clocks = <&tegra_car TEGRA124_CLK_USB2>; + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + osc: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <112400000>; + }; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k> <&osc>; + }; + + clock@60006000 { + emc-timings-3 { + nvidia,ram-code = <3>; + + timing-12750000 { + clock-frequency = <12750000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + timing-20400000 { + clock-frequency = <20400000>; + nvidia,parent-clock-frequency = <408000000>; + clocks = <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "emc-parent"; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt new file mode 100644 index 000000000..dff236f52 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt @@ -0,0 +1,78 @@ +NVIDIA Tegra124 DFLL FCPU clocksource + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The DFLL IP block on Tegra is a root clocksource designed for clocking +the fast CPU cluster. It consists of a free-running voltage controlled +oscillator connected to the CPU voltage rail (VDD_CPU), and a closed loop +control module that will automatically adjust the VDD_CPU voltage by +communicating with an off-chip PMIC either via an I2C bus or via PWM signals. +Currently only the I2C mode is supported by these bindings. + +Required properties: +- compatible : should be "nvidia,tegra124-dfll" +- reg : Defines the following set of registers, in the order listed: + - registers for the DFLL control logic. + - registers for the I2C output logic. + - registers for the integrated I2C master controller. + - look-up table RAM for voltage register values. +- interrupts: Should contain the DFLL block interrupt. +- clocks: Must contain an entry for each entry in clock-names. + See clock-bindings.txt for details. +- clock-names: Must include the following entries: + - soc: Clock source for the DFLL control logic. + - ref: The closed loop reference clock + - i2c: Clock source for the integrated I2C master. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - dvco: Reset control for the DFLL DVCO. +- #clock-cells: Must be 0. +- clock-output-names: Name of the clock output. +- vdd-cpu-supply: Regulator for the CPU voltage rail that the DFLL + hardware will start controlling. The regulator will be queried for + the I2C register, control values and supported voltages. + +Required properties for the control loop parameters: +- nvidia,sample-rate: Sample rate of the DFLL control loop. +- nvidia,droop-ctrl: See the register CL_DVFS_DROOP_CTRL in the TRM. +- nvidia,force-mode: See the field DFLL_PARAMS_FORCE_MODE in the TRM. +- nvidia,cf: Numeric value, see the field DFLL_PARAMS_CF_PARAM in the TRM. +- nvidia,ci: Numeric value, see the field DFLL_PARAMS_CI_PARAM in the TRM. +- nvidia,cg: Numeric value, see the field DFLL_PARAMS_CG_PARAM in the TRM. + +Optional properties for the control loop parameters: +- nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM. + +Required properties for I2C mode: +- nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode. + +Example: + +clock@70110000 { + compatible = "nvidia,tegra124-dfll"; + reg = <0 0x70110000 0 0x100>, /* DFLL control */ + <0 0x70110000 0 0x100>, /* I2C output control */ + <0 0x70110100 0 0x100>, /* Integrated I2C controller */ + <0 0x70110200 0 0x100>; /* Look-up table RAM */ + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_DFLL_SOC>, + <&tegra_car TEGRA124_CLK_DFLL_REF>, + <&tegra_car TEGRA124_CLK_I2C5>; + clock-names = "soc", "ref", "i2c"; + resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>; + reset-names = "dvco"; + #clock-cells = <0>; + clock-output-names = "dfllCPU_out"; + vdd-cpu-supply = <&vdd_cpu>; + + nvidia,sample-rate = <12500>; + nvidia,droop-ctrl = <0x00000f00>; + nvidia,force-mode = <1>; + nvidia,cf = <10>; + nvidia,ci = <0>; + nvidia,cg = <2>; + + nvidia,i2c-fs-rate = <400000>; +}; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt new file mode 100644 index 000000000..6c5901b50 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra20-car.txt @@ -0,0 +1,63 @@ +NVIDIA Tegra20 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra20-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in", and the board-specific oscillator "osc". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the + CAR. The assignments may be found in header file + <dt-bindings/clock/tegra20-car.h>. +- #reset-cells : Should be 1. + In clock consumers, this cell represents the bit number in the CAR's + array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. + +Example SoC include file: + +/ { + tegra_car: clock { + compatible = "nvidia,tegra20-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car TEGRA20_CLK_USB2>; + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + osc: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k> <&osc>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra210-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra210-car.txt new file mode 100644 index 000000000..26f237f64 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra210-car.txt @@ -0,0 +1,56 @@ +NVIDIA Tegra210 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra210-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the + CAR. The assignments may be found in header file + <dt-bindings/clock/tegra210-car.h>. +- #reset-cells : Should be 1. + In clock consumers, this cell represents the bit number in the CAR's + array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. + +Example SoC include file: + +/ { + tegra_car: clock { + compatible = "nvidia,tegra210-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car TEGRA210_CLK_USB2>; + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt new file mode 100644 index 000000000..63618cde1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra30-car.txt @@ -0,0 +1,63 @@ +NVIDIA Tegra30 Clock And Reset Controller + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The CAR (Clock And Reset) Controller on Tegra is the HW module responsible +for muxing and gating Tegra's clocks, and setting their rates. + +Required properties : +- compatible : Should be "nvidia,tegra30-car" +- reg : Should contain CAR registers location and length +- clocks : Should contain phandle and clock specifiers for two clocks: + the 32 KHz "32k_in", and the board-specific oscillator "osc". +- #clock-cells : Should be 1. + In clock consumers, this cell represents the clock ID exposed by the + CAR. The assignments may be found in header file + <dt-bindings/clock/tegra30-car.h>. +- #reset-cells : Should be 1. + In clock consumers, this cell represents the bit number in the CAR's + array of CLK_RST_CONTROLLER_RST_DEVICES_* registers. + +Example SoC include file: + +/ { + tegra_car: clock { + compatible = "nvidia,tegra30-car"; + reg = <0x60006000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + usb@c5004000 { + clocks = <&tegra_car TEGRA30_CLK_USB2>; + }; +}; + +Example board file: + +/ { + clocks { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + osc: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <12000000>; + }; + + clk_32k: clock@1 { + compatible = "fixed-clock"; + reg = <1>; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + }; + + &tegra_car { + clocks = <&clk_32k> <&osc>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/nxp,lpc3220-clk.txt b/Documentation/devicetree/bindings/clock/nxp,lpc3220-clk.txt new file mode 100644 index 000000000..20cbca3f4 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nxp,lpc3220-clk.txt @@ -0,0 +1,30 @@ +NXP LPC32xx Clock Controller + +Required properties: +- compatible: should be "nxp,lpc3220-clk" +- reg: should contain clock controller registers location and length +- #clock-cells: must be 1, the cell holds id of a clock provided by the + clock controller +- clocks: phandles of external oscillators, the list must contain one + 32768 Hz oscillator and may have one optional high frequency oscillator +- clock-names: list of external oscillator clock names, must contain + "xtal_32k" and may have optional "xtal" + +Examples: + + /* System Control Block */ + scb { + compatible = "simple-bus"; + ranges = <0x0 0x040004000 0x00001000>; + #address-cells = <1>; + #size-cells = <1>; + + clk: clock-controller@0 { + compatible = "nxp,lpc3220-clk"; + reg = <0x00 0x114>; + #clock-cells = <1>; + + clocks = <&xtal_32k>, <&xtal>; + clock-names = "xtal_32k", "xtal"; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/nxp,lpc3220-usb-clk.txt b/Documentation/devicetree/bindings/clock/nxp,lpc3220-usb-clk.txt new file mode 100644 index 000000000..0aa249409 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/nxp,lpc3220-usb-clk.txt @@ -0,0 +1,22 @@ +NXP LPC32xx USB Clock Controller + +Required properties: +- compatible: should be "nxp,lpc3220-usb-clk" +- reg: should contain clock controller registers location and length +- #clock-cells: must be 1, the cell holds id of a clock provided by the + USB clock controller + +Examples: + + usb { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + ranges = <0x0 0x31020000 0x00001000>; + + usbclk: clock-controller@f00 { + compatible = "nxp,lpc3220-usb-clk"; + reg = <0xf00 0x100>; + #clock-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt b/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt new file mode 100644 index 000000000..b652f3fb7 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/oxnas,stdclk.txt @@ -0,0 +1,28 @@ +Oxford Semiconductor OXNAS SoC Family Standard Clocks +================================================ + +Please also refer to clock-bindings.txt in this directory for common clock +bindings usage. + +Required properties: +- compatible: For OX810SE, should be "oxsemi,ox810se-stdclk" + For OX820, should be "oxsemi,ox820-stdclk" +- #clock-cells: 1, see below + +Parent node should have the following properties : +- compatible: For OX810SE, should be + "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd" + For OX820, should be + "oxsemi,ox820-sys-ctrl", "syscon", "simple-mfd" + +example: + +sys: sys-ctrl@000000 { + compatible = "oxsemi,ox810se-sys-ctrl", "syscon", "simple-mfd"; + reg = <0x000000 0x100000>; + + stdclk: stdclk { + compatible = "oxsemi,ox810se-stdclk"; + #clock-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/pistachio-clock.txt b/Documentation/devicetree/bindings/clock/pistachio-clock.txt new file mode 100644 index 000000000..868db499e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/pistachio-clock.txt @@ -0,0 +1,123 @@ +Imagination Technologies Pistachio SoC clock controllers +======================================================== + +Pistachio has four clock controllers (core clock, peripheral clock, peripheral +general control, and top general control) which are instantiated individually +from the device-tree. + +External clocks: +---------------- + +There are three external inputs to the clock controllers which should be +defined with the following clock-output-names: +- "xtal": External 52Mhz oscillator (required) +- "audio_clk_in": Alternate audio reference clock (optional) +- "enet_clk_in": Alternate ethernet PHY clock (optional) + +Core clock controller: +---------------------- + +The core clock controller generates clocks for the CPU, RPU (WiFi + BT +co-processor), audio, and several peripherals. + +Required properties: +- compatible: Must be "img,pistachio-clk". +- reg: Must contain the base address and length of the core clock controller. +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Must include "xtal" (see "External clocks") and + "audio_clk_in_gate", "enet_clk_in_gate" which are generated by the + top-level general control. + +Example: + clk_core: clock-controller@18144000 { + compatible = "img,pistachio-clk"; + reg = <0x18144000 0x800>; + clocks = <&xtal>, <&cr_top EXT_CLK_AUDIO_IN>, + <&cr_top EXT_CLK_ENET_IN>; + clock-names = "xtal", "audio_clk_in_gate", "enet_clk_in_gate"; + + #clock-cells = <1>; + }; + +Peripheral clock controller: +---------------------------- + +The peripheral clock controller generates clocks for the DDR, ROM, and other +peripherals. The peripheral system clock ("periph_sys") generated by the core +clock controller is the input clock to the peripheral clock controller. + +Required properties: +- compatible: Must be "img,pistachio-periph-clk". +- reg: Must contain the base address and length of the peripheral clock + controller. +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Must include "periph_sys", the peripheral system clock generated + by the core clock controller. + +Example: + clk_periph: clock-controller@18144800 { + compatible = "img,pistachio-clk-periph"; + reg = <0x18144800 0x800>; + clocks = <&clk_core CLK_PERIPH_SYS>; + clock-names = "periph_sys"; + + #clock-cells = <1>; + }; + +Peripheral general control: +--------------------------- + +The peripheral general control block generates system interface clocks and +resets for various peripherals. It also contains miscellaneous peripheral +control registers. The system clock ("sys") generated by the peripheral clock +controller is the input clock to the system clock controller. + +Required properties: +- compatible: Must include "img,pistachio-periph-cr" and "syscon". +- reg: Must contain the base address and length of the peripheral general + control registers. +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Must include "sys", the system clock generated by the peripheral + clock controller. + +Example: + cr_periph: syscon@18144800 { + compatible = "img,pistachio-cr-periph", "syscon"; + reg = <0x18148000 0x1000>; + clocks = <&clock_periph PERIPH_CLK_PERIPH_SYS>; + clock-names = "sys"; + + #clock-cells = <1>; + }; + +Top-level general control: +-------------------------- + +The top-level general control block contains miscellaneous control registers and +gates for the external clocks "audio_clk_in" and "enet_clk_in". + +Required properties: +- compatible: Must include "img,pistachio-cr-top" and "syscon". +- reg: Must contain the base address and length of the top-level + control registers. +- clocks: Must contain an entry for each clock in clock-names. +- clock-names: Two optional clocks, "audio_clk_in" and "enet_clk_in" (see + "External clocks"). +- #clock-cells: Must be 1. The single cell is the clock identifier. + See dt-bindings/clock/pistachio-clk.h for the list of valid identifiers. + +Example: + cr_top: syscon@18144800 { + compatible = "img,pistachio-cr-top", "syscon"; + reg = <0x18149000 0x200>; + clocks = <&audio_refclk>, <&ext_enet_in>; + clock-names = "audio_clk_in", "enet_clk_in"; + + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/prima2-clock.txt b/Documentation/devicetree/bindings/clock/prima2-clock.txt new file mode 100644 index 000000000..5016979c0 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/prima2-clock.txt @@ -0,0 +1,73 @@ +* Clock bindings for CSR SiRFprimaII + +Required properties: +- compatible: Should be "sirf,prima2-clkc" +- reg: Address and length of the register set +- interrupts: Should contain clock controller interrupt +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. The following is a full list of prima2 +clocks and IDs. + + Clock ID + --------------------------- + rtc 0 + osc 1 + pll1 2 + pll2 3 + pll3 4 + mem 5 + sys 6 + security 7 + dsp 8 + gps 9 + mf 10 + io 11 + cpu 12 + uart0 13 + uart1 14 + uart2 15 + tsc 16 + i2c0 17 + i2c1 18 + spi0 19 + spi1 20 + pwmc 21 + efuse 22 + pulse 23 + dmac0 24 + dmac1 25 + nand 26 + audio 27 + usp0 28 + usp1 29 + usp2 30 + vip 31 + gfx 32 + mm 33 + lcd 34 + vpp 35 + mmc01 36 + mmc23 37 + mmc45 38 + usbpll 39 + usb0 40 + usb1 41 + +Examples: + +clks: clock-controller@88000000 { + compatible = "sirf,prima2-clkc"; + reg = <0x88000000 0x1000>; + interrupts = <3>; + #clock-cells = <1>; +}; + +i2c0: i2c@b00e0000 { + cell-index = <0>; + compatible = "sirf,prima2-i2c"; + reg = <0xb00e0000 0x10000>; + interrupts = <24>; + clocks = <&clks 17>; +}; diff --git a/Documentation/devicetree/bindings/clock/pwm-clock.txt b/Documentation/devicetree/bindings/clock/pwm-clock.txt new file mode 100644 index 000000000..83db876b3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/pwm-clock.txt @@ -0,0 +1,26 @@ +Binding for an external clock signal driven by a PWM pin. + +This binding uses the common clock binding[1] and the common PWM binding[2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/pwm/pwm.txt + +Required properties: +- compatible : shall be "pwm-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- pwms : from common PWM binding; this determines the clock frequency + via the period given in the PWM specifier. + +Optional properties: +- clock-output-names : From common clock binding. +- clock-frequency : Exact output frequency, in case the PWM period + is not exact but was rounded to nanoseconds. + +Example: + clock { + compatible = "pwm-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + clock-output-names = "mipi_mclk"; + pwms = <&pwm2 0 40>; /* 1 / 40 ns = 25 MHz */ + }; diff --git a/Documentation/devicetree/bindings/clock/pxa-clock.txt b/Documentation/devicetree/bindings/clock/pxa-clock.txt new file mode 100644 index 000000000..8f6723941 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/pxa-clock.txt @@ -0,0 +1,15 @@ +* Clock bindings for Marvell PXA chips + +Required properties: +- compatible: Should be "marvell,pxa-clocks" +- #clock-cells: Should be <1> + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell (see include/.../pxa-clock.h). + +Examples: + +pxa2xx_clks: pxa2xx_clks@41300004 { + compatible = "marvell,pxa-clocks"; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt b/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt new file mode 100644 index 000000000..241fb0545 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qca,ath79-pll.txt @@ -0,0 +1,33 @@ +Binding for Qualcomm Atheros AR7xxx/AR9XXX PLL controller + +The PPL controller provides the 3 main clocks of the SoC: CPU, DDR and AHB. + +Required Properties: +- compatible: has to be "qca,<soctype>-pll" and one of the following + fallbacks: + - "qca,ar7100-pll" + - "qca,ar7240-pll" + - "qca,ar9130-pll" + - "qca,ar9330-pll" + - "qca,ar9340-pll" + - "qca,qca9550-pll" +- reg: Base address and size of the controllers memory area +- clock-names: Name of the input clock, has to be "ref" +- clocks: phandle of the external reference clock +- #clock-cells: has to be one + +Optional properties: +- clock-output-names: should be "cpu", "ddr", "ahb" + +Example: + + pll-controller@18050000 { + compatible = "qca,ar9132-pll", "qca,ar9130-pll"; + reg = <0x18050000 0x20>; + + clock-names = "ref"; + clocks = <&extosc>; + + #clock-cells = <1>; + clock-output-names = "cpu", "ddr", "ahb"; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,a53pll.txt b/Documentation/devicetree/bindings/clock/qcom,a53pll.txt new file mode 100644 index 000000000..e3fa8118e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,a53pll.txt @@ -0,0 +1,22 @@ +Qualcomm MSM8916 A53 PLL Binding +-------------------------------- +The A53 PLL on MSM8916 platforms is the main CPU PLL used used for frequencies +above 1GHz. + +Required properties : +- compatible : Shall contain only one of the following: + + "qcom,msm8916-a53pll" + +- reg : shall contain base register location and length + +- #clock-cells : must be set to <0> + +Example: + + a53pll: clock@b016000 { + compatible = "qcom,msm8916-a53pll"; + reg = <0xb016000 0x40>; + #clock-cells = <0>; + }; + diff --git a/Documentation/devicetree/bindings/clock/qcom,dispcc.txt b/Documentation/devicetree/bindings/clock/qcom,dispcc.txt new file mode 100644 index 000000000..d639e18d0 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,dispcc.txt @@ -0,0 +1,19 @@ +Qualcomm Technologies, Inc. Display Clock Controller Binding +------------------------------------------------------------ + +Required properties : + +- compatible : shall contain "qcom,sdm845-dispcc" +- reg : shall contain base register location and length. +- #clock-cells : from common clock binding, shall contain 1. +- #reset-cells : from common reset binding, shall contain 1. +- #power-domain-cells : from generic power domain binding, shall contain 1. + +Example: + dispcc: clock-controller@af00000 { + compatible = "qcom,sdm845-dispcc"; + reg = <0xaf00000 0x100000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,gcc.txt b/Documentation/devicetree/bindings/clock/qcom,gcc.txt new file mode 100644 index 000000000..664ea1fd6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,gcc.txt @@ -0,0 +1,54 @@ +Qualcomm Global Clock & Reset Controller Binding +------------------------------------------------ + +Required properties : +- compatible : shall contain only one of the following: + + "qcom,gcc-apq8064" + "qcom,gcc-apq8084" + "qcom,gcc-ipq8064" + "qcom,gcc-ipq4019" + "qcom,gcc-ipq8074" + "qcom,gcc-msm8660" + "qcom,gcc-msm8916" + "qcom,gcc-msm8960" + "qcom,gcc-msm8974" + "qcom,gcc-msm8974pro" + "qcom,gcc-msm8974pro-ac" + "qcom,gcc-msm8994" + "qcom,gcc-msm8996" + "qcom,gcc-msm8998" + "qcom,gcc-mdm9615" + "qcom,gcc-sdm845" + +- reg : shall contain base register location and length +- #clock-cells : shall contain 1 +- #reset-cells : shall contain 1 + +Optional properties : +- #power-domain-cells : shall contain 1 +- Qualcomm TSENS (thermal sensor device) on some devices can +be part of GCC and hence the TSENS properties can also be +part of the GCC/clock-controller node. +For more details on the TSENS properties please refer +Documentation/devicetree/bindings/thermal/qcom-tsens.txt + +Example: + clock-controller@900000 { + compatible = "qcom,gcc-msm8960"; + reg = <0x900000 0x4000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + +Example of GCC with TSENS properties: + clock-controller@900000 { + compatible = "qcom,gcc-apq8064"; + reg = <0x00900000 0x4000>; + nvmem-cells = <&tsens_calib>, <&tsens_backup>; + nvmem-cell-names = "calib", "calib_backup"; + #clock-cells = <1>; + #reset-cells = <1>; + #thermal-sensor-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,lcc.txt b/Documentation/devicetree/bindings/clock/qcom,lcc.txt new file mode 100644 index 000000000..a3c78aa88 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,lcc.txt @@ -0,0 +1,22 @@ +Qualcomm LPASS Clock & Reset Controller Binding +------------------------------------------------ + +Required properties : +- compatible : shall contain only one of the following: + + "qcom,lcc-msm8960" + "qcom,lcc-apq8064" + "qcom,lcc-ipq8064" + "qcom,lcc-mdm9615" + +- reg : shall contain base register location and length +- #clock-cells : shall contain 1 +- #reset-cells : shall contain 1 + +Example: + clock-controller@28000000 { + compatible = "qcom,lcc-ipq8064"; + reg = <0x28000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,mmcc.txt b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt new file mode 100644 index 000000000..8b0f7841a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,mmcc.txt @@ -0,0 +1,28 @@ +Qualcomm Multimedia Clock & Reset Controller Binding +---------------------------------------------------- + +Required properties : +- compatible : shall contain only one of the following: + + "qcom,mmcc-apq8064" + "qcom,mmcc-apq8084" + "qcom,mmcc-msm8660" + "qcom,mmcc-msm8960" + "qcom,mmcc-msm8974" + "qcom,mmcc-msm8996" + +- reg : shall contain base register location and length +- #clock-cells : shall contain 1 +- #reset-cells : shall contain 1 + +Optional properties : +- #power-domain-cells : shall contain 1 + +Example: + clock-controller@4000000 { + compatible = "qcom,mmcc-msm8960"; + reg = <0x4000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt new file mode 100644 index 000000000..4491d1c10 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,rpmcc.txt @@ -0,0 +1,49 @@ +Qualcomm RPM Clock Controller Binding +------------------------------------------------ +The RPM is a dedicated hardware engine for managing the shared +SoC resources in order to keep the lowest power profile. It +communicates with other hardware subsystems via shared memory +and accepts clock requests, aggregates the requests and turns +the clocks on/off or scales them on demand. + +Required properties : +- compatible : shall contain only one of the following. The generic + compatible "qcom,rpmcc" should be also included. + + "qcom,rpmcc-msm8660", "qcom,rpmcc" + "qcom,rpmcc-apq8060", "qcom,rpmcc" + "qcom,rpmcc-msm8916", "qcom,rpmcc" + "qcom,rpmcc-msm8974", "qcom,rpmcc" + "qcom,rpmcc-apq8064", "qcom,rpmcc" + "qcom,rpmcc-msm8996", "qcom,rpmcc" + +- #clock-cells : shall contain 1 + +The clock enumerators are defined in <dt-bindings/clock/qcom,rpmcc.h> +and come in pairs: FOO_CLK followed by FOO_A_CLK. The latter clock +is an "active" clock, which means that the consumer only care that the +clock is available when the apps CPU subsystem is active, i.e. not +suspended or in deep idle. If it is important that the clock keeps running +during system suspend, you need to specify the non-active clock, the one +not containing *_A_* in the enumerator name. + +Example: + smd { + compatible = "qcom,smd"; + + rpm { + interrupts = <0 168 1>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests { + compatible = "qcom,rpm-msm8916"; + qcom,smd-channels = "rpm_requests"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-msm8916", "qcom,rpmcc"; + #clock-cells = <1>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt b/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt new file mode 100644 index 000000000..3c007653d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,rpmh-clk.txt @@ -0,0 +1,22 @@ +Qualcomm Technologies, Inc. RPMh Clocks +------------------------------------------------------- + +Resource Power Manager Hardened (RPMh) manages shared resources on +some Qualcomm Technologies Inc. SoCs. It accepts clock requests from +other hardware subsystems via RSC to control clocks. + +Required properties : +- compatible : shall contain "qcom,sdm845-rpmh-clk" + +- #clock-cells : must contain 1 + +Example : + +#include <dt-bindings/clock/qcom,rpmh.h> + + &apps_rsc { + rpmhcc: clock-controller { + compatible = "qcom,sdm845-rpmh-clk"; + #clock-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/qcom,spmi-clkdiv.txt b/Documentation/devicetree/bindings/clock/qcom,spmi-clkdiv.txt new file mode 100644 index 000000000..7474aba36 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,spmi-clkdiv.txt @@ -0,0 +1,59 @@ +Qualcomm Technologies, Inc. SPMI PMIC clock divider (clkdiv) + +clkdiv configures the clock frequency of a set of outputs on the PMIC. +These clocks are typically wired through alternate functions on +gpio pins. + +======================= +Properties +======================= + +- compatible + Usage: required + Value type: <string> + Definition: must be "qcom,spmi-clkdiv". + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: base address of CLKDIV peripherals. + +- qcom,num-clkdivs + Usage: required + Value type: <u32> + Definition: number of CLKDIV peripherals. + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: reference to the xo clock. + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: must be "xo". + +- #clock-cells: + Usage: required + Value type: <u32> + Definition: shall contain 1. + +======= +Example +======= + +pm8998_clk_divs: clock-controller@5b00 { + compatible = "qcom,spmi-clkdiv"; + reg = <0x5b00>; + #clock-cells = <1>; + qcom,num-clkdivs = <3>; + clocks = <&xo_board>; + clock-names = "xo"; + + assigned-clocks = <&pm8998_clk_divs 1>, + <&pm8998_clk_divs 2>, + <&pm8998_clk_divs 3>; + assigned-clock-rates = <9600000>, + <9600000>, + <9600000>; +}; diff --git a/Documentation/devicetree/bindings/clock/qcom,videocc.txt b/Documentation/devicetree/bindings/clock/qcom,videocc.txt new file mode 100644 index 000000000..e7c035afa --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,videocc.txt @@ -0,0 +1,19 @@ +Qualcomm Video Clock & Reset Controller Binding +----------------------------------------------- + +Required properties : +- compatible : shall contain "qcom,sdm845-videocc" +- reg : shall contain base register location and length +- #clock-cells : from common clock binding, shall contain 1. +- #power-domain-cells : from generic power domain binding, shall contain 1. + +Optional properties : +- #reset-cells : from common reset binding, shall contain 1. + +Example: + videocc: clock-controller@ab00000 { + compatible = "qcom,sdm845-videocc"; + reg = <0xab00000 0x10000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/qoriq-clock.txt b/Documentation/devicetree/bindings/clock/qoriq-clock.txt new file mode 100644 index 000000000..97f46adac --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qoriq-clock.txt @@ -0,0 +1,204 @@ +* Clock Block on Freescale QorIQ Platforms + +Freescale QorIQ chips take primary clocking input from the external +SYSCLK signal. The SYSCLK input (frequency) is multiplied using +multiple phase locked loops (PLL) to create a variety of frequencies +which can then be passed to a variety of internal logic, including +cores and peripheral IP blocks. +Please refer to the Reference Manual for details. + +All references to "1.0" and "2.0" refer to the QorIQ chassis version to +which the chip complies. + +Chassis Version Example Chips +--------------- ------------- +1.0 p4080, p5020, p5040 +2.0 t4240, b4860 + +1. Clock Block Binding + +Required properties: +- compatible: Should contain a chip-specific clock block compatible + string and (if applicable) may contain a chassis-version clock + compatible string. + + Chip-specific strings are of the form "fsl,<chip>-clockgen", such as: + * "fsl,p2041-clockgen" + * "fsl,p3041-clockgen" + * "fsl,p4080-clockgen" + * "fsl,p5020-clockgen" + * "fsl,p5040-clockgen" + * "fsl,t4240-clockgen" + * "fsl,b4420-clockgen" + * "fsl,b4860-clockgen" + * "fsl,ls1012a-clockgen" + * "fsl,ls1021a-clockgen" + * "fsl,ls1043a-clockgen" + * "fsl,ls1046a-clockgen" + * "fsl,ls1088a-clockgen" + * "fsl,ls2080a-clockgen" + Chassis-version clock strings include: + * "fsl,qoriq-clockgen-1.0": for chassis 1.0 clocks + * "fsl,qoriq-clockgen-2.0": for chassis 2.0 clocks +- reg: Describes the address of the device's resources within the + address space defined by its parent bus, and resource zero + represents the clock register set + +Optional properties: +- ranges: Allows valid translation between child's address space and + parent's. Must be present if the device has sub-nodes. +- #address-cells: Specifies the number of cells used to represent + physical base addresses. Must be present if the device has + sub-nodes and set to 1 if present +- #size-cells: Specifies the number of cells used to represent + the size of an address. Must be present if the device has + sub-nodes and set to 1 if present +- clock-frequency: Input system clock frequency (SYSCLK) +- clocks: If clock-frequency is not specified, sysclk may be provided + as an input clock. Either clock-frequency or clocks must be + provided. + A second input clock, called "coreclk", may be provided if + core PLLs are based on a different input clock from the + platform PLL. +- clock-names: Required if a coreclk is present. Valid names are + "sysclk" and "coreclk". + +2. Clock Provider + +The clockgen node should act as a clock provider, though in older device +trees the children of the clockgen node are the clock providers. + +When the clockgen node is a clock provider, #clock-cells = <2>. +The first cell of the clock specifier is the clock type, and the +second cell is the clock index for the specified type. + + Type# Name Index Cell + 0 sysclk must be 0 + 1 cmux index (n in CLKCnCSR) + 2 hwaccel index (n in CLKCGnHWACSR) + 3 fman 0 for fm1, 1 for fm2 + 4 platform pll 0=pll, 1=pll/2, 2=pll/3, 3=pll/4 + 4=pll/5, 5=pll/6, 6=pll/7, 7=pll/8 + 5 coreclk must be 0 + +3. Example + + clockgen: global-utilities@e1000 { + compatible = "fsl,p5020-clockgen", "fsl,qoriq-clockgen-1.0"; + clock-frequency = <133333333>; + reg = <0xe1000 0x1000>; + #clock-cells = <2>; + }; + + fman@400000 { + ... + clocks = <&clockgen 3 0>; + ... + }; +} +4. Legacy Child Nodes + +NOTE: These nodes are deprecated. Kernels should continue to support +device trees with these nodes, but new device trees should not use them. + +Most of the bindings are from the common clock binding[1]. + [1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : Should include one of the following: + * "fsl,qoriq-core-pll-1.0" for core PLL clocks (v1.0) + * "fsl,qoriq-core-pll-2.0" for core PLL clocks (v2.0) + * "fsl,qoriq-core-mux-1.0" for core mux clocks (v1.0) + * "fsl,qoriq-core-mux-2.0" for core mux clocks (v2.0) + * "fsl,qoriq-sysclk-1.0": for input system clock (v1.0). + It takes parent's clock-frequency as its clock. + * "fsl,qoriq-sysclk-2.0": for input system clock (v2.0). + It takes parent's clock-frequency as its clock. + * "fsl,qoriq-platform-pll-1.0" for the platform PLL clock (v1.0) + * "fsl,qoriq-platform-pll-2.0" for the platform PLL clock (v2.0) +- #clock-cells: From common clock binding. The number of cells in a + clock-specifier. Should be <0> for "fsl,qoriq-sysclk-[1,2].0" + clocks, or <1> for "fsl,qoriq-core-pll-[1,2].0" clocks. + For "fsl,qoriq-core-pll-[1,2].0" clocks, the single + clock-specifier cell may take the following values: + * 0 - equal to the PLL frequency + * 1 - equal to the PLL frequency divided by 2 + * 2 - equal to the PLL frequency divided by 4 + +Recommended properties: +- clocks: Should be the phandle of input parent clock +- clock-names: From common clock binding, indicates the clock name +- clock-output-names: From common clock binding, indicates the names of + output clocks +- reg: Should be the offset and length of clock block base address. + The length should be 4. + +Legacy Example: +/ { + clockgen: global-utilities@e1000 { + compatible = "fsl,p5020-clockgen", "fsl,qoriq-clockgen-1.0"; + ranges = <0x0 0xe1000 0x1000>; + clock-frequency = <133333333>; + reg = <0xe1000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + sysclk: sysclk { + #clock-cells = <0>; + compatible = "fsl,qoriq-sysclk-1.0"; + clock-output-names = "sysclk"; + }; + + pll0: pll0@800 { + #clock-cells = <1>; + reg = <0x800 0x4>; + compatible = "fsl,qoriq-core-pll-1.0"; + clocks = <&sysclk>; + clock-output-names = "pll0", "pll0-div2"; + }; + + pll1: pll1@820 { + #clock-cells = <1>; + reg = <0x820 0x4>; + compatible = "fsl,qoriq-core-pll-1.0"; + clocks = <&sysclk>; + clock-output-names = "pll1", "pll1-div2"; + }; + + mux0: mux0@0 { + #clock-cells = <0>; + reg = <0x0 0x4>; + compatible = "fsl,qoriq-core-mux-1.0"; + clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>; + clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2"; + clock-output-names = "cmux0"; + }; + + mux1: mux1@20 { + #clock-cells = <0>; + reg = <0x20 0x4>; + compatible = "fsl,qoriq-core-mux-1.0"; + clocks = <&pll0 0>, <&pll0 1>, <&pll1 0>, <&pll1 1>; + clock-names = "pll0", "pll0-div2", "pll1", "pll1-div2"; + clock-output-names = "cmux1"; + }; + + platform-pll: platform-pll@c00 { + #clock-cells = <1>; + reg = <0xc00 0x4>; + compatible = "fsl,qoriq-platform-pll-1.0"; + clocks = <&sysclk>; + clock-output-names = "platform-pll", "platform-pll-div2"; + }; + }; +}; + +Example for legacy clock consumer: + +/ { + cpu0: PowerPC,e5500@0 { + ... + clocks = <&mux0>; + ... + }; +}; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt new file mode 100644 index 000000000..ae36ab842 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-div6-clocks.txt @@ -0,0 +1,40 @@ +* Renesas CPG DIV6 Clock + +The CPG DIV6 clocks are variable factor clocks provided by the Clock Pulse +Generator (CPG). Their clock input is divided by a configurable factor from 1 +to 64. + +Required Properties: + + - compatible: Must be one of the following + - "renesas,r8a73a4-div6-clock" for R8A73A4 (R-Mobile APE6) DIV6 clocks + - "renesas,r8a7740-div6-clock" for R8A7740 (R-Mobile A1) DIV6 clocks + - "renesas,r8a7790-div6-clock" for R8A7790 (R-Car H2) DIV6 clocks + - "renesas,r8a7791-div6-clock" for R8A7791 (R-Car M2-W) DIV6 clocks + - "renesas,r8a7793-div6-clock" for R8A7793 (R-Car M2-N) DIV6 clocks + - "renesas,r8a7794-div6-clock" for R8A7794 (R-Car E2) DIV6 clocks + - "renesas,sh73a0-div6-clock" for SH73A0 (SH-Mobile AG5) DIV6 clocks + and "renesas,cpg-div6-clock" as a fallback. + - reg: Base address and length of the memory resource used by the DIV6 clock + - clocks: Reference to the parent clock(s); either one, four, or eight + clocks must be specified. For clocks with multiple parents, invalid + settings must be specified as "<0>". + - #clock-cells: Must be 0 + + +Optional Properties: + + - clock-output-names: The name of the clock as a free-form string + + +Example +------- + + sdhi2_clk: sdhi2_clk@e615007c { + compatible = "renesas,r8a73a4-div6-clock", "renesas,cpg-div6-clock"; + reg = <0 0xe615007c 0 4>; + clocks = <&pll1_div2_clk>, <&cpg_clocks R8A73A4_CLK_PLL2S>, + <0>, <&extal2_clk>; + #clock-cells = <0>; + clock-output-names = "sdhi2ck"; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt new file mode 100644 index 000000000..db542abad --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mssr.txt @@ -0,0 +1,92 @@ +* Renesas Clock Pulse Generator / Module Standby and Software Reset + +On Renesas ARM SoCs (SH/R-Mobile, R-Car, RZ), the CPG (Clock Pulse Generator) +and MSSR (Module Standby and Software Reset) blocks are intimately connected, +and share the same register block. + +They provide the following functionalities: + - The CPG block generates various core clocks, + - The MSSR block provides two functions: + 1. Module Standby, providing a Clock Domain to control the clock supply + to individual SoC devices, + 2. Reset Control, to perform a software reset of individual SoC devices. + +Required Properties: + - compatible: Must be one of: + - "renesas,r8a7743-cpg-mssr" for the r8a7743 SoC (RZ/G1M) + - "renesas,r8a7745-cpg-mssr" for the r8a7745 SoC (RZ/G1E) + - "renesas,r8a77470-cpg-mssr" for the r8a77470 SoC (RZ/G1C) + - "renesas,r8a7790-cpg-mssr" for the r8a7790 SoC (R-Car H2) + - "renesas,r8a7791-cpg-mssr" for the r8a7791 SoC (R-Car M2-W) + - "renesas,r8a7792-cpg-mssr" for the r8a7792 SoC (R-Car V2H) + - "renesas,r8a7793-cpg-mssr" for the r8a7793 SoC (R-Car M2-N) + - "renesas,r8a7794-cpg-mssr" for the r8a7794 SoC (R-Car E2) + - "renesas,r8a7795-cpg-mssr" for the r8a7795 SoC (R-Car H3) + - "renesas,r8a7796-cpg-mssr" for the r8a7796 SoC (R-Car M3-W) + - "renesas,r8a77965-cpg-mssr" for the r8a77965 SoC (R-Car M3-N) + - "renesas,r8a77970-cpg-mssr" for the r8a77970 SoC (R-Car V3M) + - "renesas,r8a77980-cpg-mssr" for the r8a77980 SoC (R-Car V3H) + - "renesas,r8a77990-cpg-mssr" for the r8a77990 SoC (R-Car E3) + - "renesas,r8a77995-cpg-mssr" for the r8a77995 SoC (R-Car D3) + + - reg: Base address and length of the memory resource used by the CPG/MSSR + block + + - clocks: References to external parent clocks, one entry for each entry in + clock-names + - clock-names: List of external parent clock names. Valid names are: + - "extal" (r8a7743, r8a7745, r8a77470, r8a7790, r8a7791, r8a7792, + r8a7793, r8a7794, r8a7795, r8a7796, r8a77965, r8a77970, + r8a77980, r8a77990, r8a77995) + - "extalr" (r8a7795, r8a7796, r8a77965, r8a77970, r8a77980) + - "usb_extal" (r8a7743, r8a7745, r8a77470, r8a7790, r8a7791, r8a7793, + r8a7794) + + - #clock-cells: Must be 2 + - For CPG core clocks, the two clock specifier cells must be "CPG_CORE" + and a core clock reference, as defined in + <dt-bindings/clock/*-cpg-mssr.h>. + - For module clocks, the two clock specifier cells must be "CPG_MOD" and + a module number, as defined in the datasheet. + + - #power-domain-cells: Must be 0 + - SoC devices that are part of the CPG/MSSR Clock Domain and can be + power-managed through Module Standby should refer to the CPG device + node in their "power-domains" property, as documented by the generic PM + Domain bindings in + Documentation/devicetree/bindings/power/power_domain.txt. + + - #reset-cells: Must be 1 + - The single reset specifier cell must be the module number, as defined + in the datasheet. + + +Examples +-------- + + - CPG device node: + + cpg: clock-controller@e6150000 { + compatible = "renesas,r8a7795-cpg-mssr"; + reg = <0 0xe6150000 0 0x1000>; + clocks = <&extal_clk>, <&extalr_clk>; + clock-names = "extal", "extalr"; + #clock-cells = <2>; + #power-domain-cells = <0>; + #reset-cells = <1>; + }; + + + - CPG/MSSR Clock Domain member device node: + + scif2: serial@e6e88000 { + compatible = "renesas,scif-r8a7795", "renesas,scif"; + reg = <0 0xe6e88000 0 64>; + interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 310>; + clock-names = "fck"; + dmas = <&dmac1 0x13>, <&dmac1 0x12>; + dma-names = "tx", "rx"; + power-domains = <&cpg>; + resets = <&cpg 310>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt new file mode 100644 index 000000000..da578ebdd --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,cpg-mstp-clocks.txt @@ -0,0 +1,60 @@ +* Renesas CPG Module Stop (MSTP) Clocks + +The CPG can gate SoC device clocks. The gates are organized in groups of up to +32 gates. + +This device tree binding describes a single 32 gate clocks group per node. +Clocks are referenced by user nodes by the MSTP node phandle and the clock +index in the group, from 0 to 31. + +Required Properties: + + - compatible: Must be one of the following + - "renesas,r7s72100-mstp-clocks" for R7S72100 (RZ) MSTP gate clocks + - "renesas,r8a73a4-mstp-clocks" for R8A73A4 (R-Mobile APE6) MSTP gate clocks + - "renesas,r8a7740-mstp-clocks" for R8A7740 (R-Mobile A1) MSTP gate clocks + - "renesas,r8a7778-mstp-clocks" for R8A7778 (R-Car M1) MSTP gate clocks + - "renesas,r8a7779-mstp-clocks" for R8A7779 (R-Car H1) MSTP gate clocks + - "renesas,r8a7790-mstp-clocks" for R8A7790 (R-Car H2) MSTP gate clocks + - "renesas,r8a7791-mstp-clocks" for R8A7791 (R-Car M2-W) MSTP gate clocks + - "renesas,r8a7792-mstp-clocks" for R8A7792 (R-Car V2H) MSTP gate clocks + - "renesas,r8a7793-mstp-clocks" for R8A7793 (R-Car M2-N) MSTP gate clocks + - "renesas,r8a7794-mstp-clocks" for R8A7794 (R-Car E2) MSTP gate clocks + - "renesas,sh73a0-mstp-clocks" for SH73A0 (SH-MobileAG5) MSTP gate clocks + and "renesas,cpg-mstp-clocks" as a fallback. + - reg: Base address and length of the I/O mapped registers used by the MSTP + clocks. The first register is the clock control register and is mandatory. + The second register is the clock status register and is optional when not + implemented in hardware. + - clocks: Reference to the parent clocks, one per output clock. The parents + must appear in the same order as the output clocks. + - #clock-cells: Must be 1 + - clock-output-names: The name of the clocks as free-form strings + - clock-indices: Indices of the gate clocks into the group (0 to 31) + +The clocks, clock-output-names and clock-indices properties contain one entry +per gate clock. The MSTP groups are sparsely populated. Unimplemented gate +clocks must not be declared. + + +Example +------- + + #include <dt-bindings/clock/r8a7790-clock.h> + + mstp3_clks: mstp3_clks@e615013c { + compatible = "renesas,r8a7790-mstp-clocks", "renesas,cpg-mstp-clocks"; + reg = <0 0xe615013c 0 4>, <0 0xe6150048 0 4>; + clocks = <&cp_clk>, <&mmc1_clk>, <&sd3_clk>, <&sd2_clk>, + <&cpg_clocks R8A7790_CLK_SD1>, <&cpg_clocks R8A7790_CLK_SD0>, + <&mmc0_clk>; + #clock-cells = <1>; + clock-output-names = + "tpu0", "mmcif1", "sdhi3", "sdhi2", + "sdhi1", "sdhi0", "mmcif0"; + clock-indices = < + R8A7790_CLK_TPU0 R8A7790_CLK_MMCIF1 R8A7790_CLK_SDHI3 + R8A7790_CLK_SDHI2 R8A7790_CLK_SDHI1 R8A7790_CLK_SDHI0 + R8A7790_CLK_MMCIF0 + >; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,h8300-div-clock.txt b/Documentation/devicetree/bindings/clock/renesas,h8300-div-clock.txt new file mode 100644 index 000000000..399e0da22 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,h8300-div-clock.txt @@ -0,0 +1,24 @@ +* Renesas H8/300 divider clock + +Required Properties: + + - compatible: Must be "renesas,h8300-div-clock" + + - clocks: Reference to the parent clocks ("extal1" and "extal2") + + - #clock-cells: Must be 1 + + - reg: Base address and length of the divide rate selector + + - renesas,width: bit width of selector + +Example +------- + + cclk: cclk { + compatible = "renesas,h8300-div-clock"; + clocks = <&xclk>; + #clock-cells = <0>; + reg = <0xfee01b 2>; + renesas,width = <2>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,h8s2678-pll-clock.txt b/Documentation/devicetree/bindings/clock/renesas,h8s2678-pll-clock.txt new file mode 100644 index 000000000..500cdadbc --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,h8s2678-pll-clock.txt @@ -0,0 +1,23 @@ +Renesas H8S2678 PLL clock + +This device is Clock multiplyer + +Required Properties: + + - compatible: Must be "renesas,h8s2678-pll-clock" + + - clocks: Reference to the parent clocks + + - #clock-cells: Must be 0 + + - reg: Two rate selector (Multiply / Divide) register address + +Example +------- + + pllclk: pllclk { + compatible = "renesas,h8s2678-pll-clock"; + clocks = <&xclk>; + #clock-cells = <0>; + reg = <0xfee03b 2>, <0xfee045 2>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a73a4-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a73a4-cpg-clocks.txt new file mode 100644 index 000000000..ece92393e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,r8a73a4-cpg-clocks.txt @@ -0,0 +1,33 @@ +* Renesas R8A73A4 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the R8A73A4 SoC. It includes five PLLs +and several fixed ratio dividers. + +Required Properties: + + - compatible: Must be "renesas,r8a73a4-cpg-clocks" + + - reg: Base address and length of the memory resource used by the CPG + + - clocks: Reference to the parent clocks ("extal1" and "extal2") + + - #clock-cells: Must be 1 + + - clock-output-names: The names of the clocks. Supported clocks are "main", + "pll0", "pll1", "pll2", "pll2s", "pll2h", "z", "z2", "i", "m3", "b", + "m1", "m2", "zx", "zs", and "hp". + + +Example +------- + + cpg_clocks: cpg_clocks@e6150000 { + compatible = "renesas,r8a73a4-cpg-clocks"; + reg = <0 0xe6150000 0 0x10000>; + clocks = <&extal1_clk>, <&extal2_clk>; + #clock-cells = <1>; + clock-output-names = "main", "pll0", "pll1", "pll2", + "pll2s", "pll2h", "z", "z2", + "i", "m3", "b", "m1", "m2", + "zx", "zs", "hp"; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a7740-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a7740-cpg-clocks.txt new file mode 100644 index 000000000..2c03302f8 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,r8a7740-cpg-clocks.txt @@ -0,0 +1,41 @@ +These bindings should be considered EXPERIMENTAL for now. + +* Renesas R8A7740 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the R8A7740 SoC. It includes three PLLs +and several fixed ratio and variable ratio dividers. + +Required Properties: + + - compatible: Must be "renesas,r8a7740-cpg-clocks" + + - reg: Base address and length of the memory resource used by the CPG + + - clocks: Reference to the three parent clocks + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are + "system", "pllc0", "pllc1", "pllc2", "r", "usb24s", "i", "zg", "b", + "m1", "hp", "hpp", "usbp", "s", "zb", "m3", and "cp". + + - renesas,mode: board-specific settings of the MD_CK* bits + + +Example +------- + +cpg_clocks: cpg_clocks@e6150000 { + compatible = "renesas,r8a7740-cpg-clocks"; + reg = <0xe6150000 0x10000>; + clocks = <&extal1_clk>, <&extal2_clk>, <&extalr_clk>; + #clock-cells = <1>; + clock-output-names = "system", "pllc0", "pllc1", + "pllc2", "r", + "usb24s", + "i", "zg", "b", "m1", "hp", + "hpp", "usbp", "s", "zb", "m3", + "cp"; +}; + +&cpg_clocks { + renesas,mode = <0x05>; +}; diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt new file mode 100644 index 000000000..7cc4c0330 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,r8a7778-cpg-clocks.txt @@ -0,0 +1,47 @@ +* Renesas R8A7778 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the R8A7778. It includes two PLLs and +several fixed ratio dividers. +The CPG also provides a Clock Domain for SoC devices, in combination with the +CPG Module Stop (MSTP) Clocks. + +Required Properties: + + - compatible: Must be "renesas,r8a7778-cpg-clocks" + - reg: Base address and length of the memory resource used by the CPG + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are + "plla", "pllb", "b", "out", "p", "s", and "s1". + - #power-domain-cells: Must be 0 + +SoC devices that are part of the CPG/MSTP Clock Domain and can be power-managed +through an MSTP clock should refer to the CPG device node in their +"power-domains" property, as documented by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. + + +Examples +-------- + + - CPG device node: + + cpg_clocks: cpg_clocks@ffc80000 { + compatible = "renesas,r8a7778-cpg-clocks"; + reg = <0xffc80000 0x80>; + #clock-cells = <1>; + clocks = <&extal_clk>; + clock-output-names = "plla", "pllb", "b", + "out", "p", "s", "s1"; + #power-domain-cells = <0>; + }; + + + - CPG/MSTP Clock Domain member device node: + + sdhi0: sd@ffe4c000 { + compatible = "renesas,sdhi-r8a7778"; + reg = <0xffe4c000 0x100>; + interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7778_CLK_SDHI0>; + power-domains = <&cpg_clocks>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt new file mode 100644 index 000000000..8c81547c2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,r8a7779-cpg-clocks.txt @@ -0,0 +1,49 @@ +* Renesas R8A7779 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the R8A7779. It includes one PLL and +several fixed ratio dividers. +The CPG also provides a Clock Domain for SoC devices, in combination with the +CPG Module Stop (MSTP) Clocks. + +Required Properties: + + - compatible: Must be "renesas,r8a7779-cpg-clocks" + - reg: Base address and length of the memory resource used by the CPG + + - clocks: Reference to the parent clock + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are "plla", + "z", "zs", "s", "s1", "p", "b", "out". + - #power-domain-cells: Must be 0 + +SoC devices that are part of the CPG/MSTP Clock Domain and can be power-managed +through an MSTP clock should refer to the CPG device node in their +"power-domains" property, as documented by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. + + +Examples +-------- + + - CPG device node: + + cpg_clocks: cpg_clocks@ffc80000 { + compatible = "renesas,r8a7779-cpg-clocks"; + reg = <0xffc80000 0x30>; + clocks = <&extal_clk>; + #clock-cells = <1>; + clock-output-names = "plla", "z", "zs", "s", "s1", "p", + "b", "out"; + #power-domain-cells = <0>; + }; + + + - CPG/MSTP Clock Domain member device node: + + sata: sata@fc600000 { + compatible = "renesas,sata-r8a7779", "renesas,rcar-sata"; + reg = <0xfc600000 0x2000>; + interrupts = <0 100 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp1_clks R8A7779_CLK_SATA>; + power-domains = <&cpg_clocks>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt b/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt new file mode 100644 index 000000000..d60b99756 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,r9a06g032-sysctrl.txt @@ -0,0 +1,43 @@ +* Renesas R9A06G032 SYSCTRL + +Required Properties: + + - compatible: Must be: + - "renesas,r9a06g032-sysctrl" + - reg: Base address and length of the SYSCTRL IO block. + - #clock-cells: Must be 1 + - clocks: References to the parent clocks: + - external 40mhz crystal. + - external (optional) 32.768khz + - external (optional) jtag input + - external (optional) RGMII_REFCLK + - clock-names: Must be: + clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext"; + +Examples +-------- + + - SYSCTRL node: + + sysctrl: system-controller@4000c000 { + compatible = "renesas,r9a06g032-sysctrl"; + reg = <0x4000c000 0x1000>; + #clock-cells = <1>; + + clocks = <&ext_mclk>, <&ext_rtc_clk>, + <&ext_jtag_clk>, <&ext_rgmii_ref>; + clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext"; + }; + + - Other nodes can use the clocks provided by SYSCTRL as in: + + #include <dt-bindings/clock/r9a06g032-sysctrl.h> + uart0: serial@40060000 { + compatible = "snps,dw-apb-uart"; + reg = <0x40060000 0x400>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&sysctrl R9A06G032_CLK_UART0>; + clock-names = "baudclk"; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt new file mode 100644 index 000000000..f8c05bb41 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-gen2-cpg-clocks.txt @@ -0,0 +1,60 @@ +* Renesas R-Car Gen2 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the R-Car Gen2 SoCs. It includes three PLLs +and several fixed ratio dividers. +The CPG also provides a Clock Domain for SoC devices, in combination with the +CPG Module Stop (MSTP) Clocks. + +Required Properties: + + - compatible: Must be one of + - "renesas,r8a7790-cpg-clocks" for the r8a7790 CPG + - "renesas,r8a7791-cpg-clocks" for the r8a7791 CPG + - "renesas,r8a7792-cpg-clocks" for the r8a7792 CPG + - "renesas,r8a7793-cpg-clocks" for the r8a7793 CPG + - "renesas,r8a7794-cpg-clocks" for the r8a7794 CPG + and "renesas,rcar-gen2-cpg-clocks" as a fallback. + + - reg: Base address and length of the memory resource used by the CPG + + - clocks: References to the parent clocks: first to the EXTAL clock, second + to the USB_EXTAL clock + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are "main", + "pll0", "pll1", "pll3", "lb", "qspi", "sdh", "sd0", "sd1", "z", "rcan", and + "adsp" + - #power-domain-cells: Must be 0 + +SoC devices that are part of the CPG/MSTP Clock Domain and can be power-managed +through an MSTP clock should refer to the CPG device node in their +"power-domains" property, as documented by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. + + +Examples +-------- + + - CPG device node: + + cpg_clocks: cpg_clocks@e6150000 { + compatible = "renesas,r8a7790-cpg-clocks", + "renesas,rcar-gen2-cpg-clocks"; + reg = <0 0xe6150000 0 0x1000>; + clocks = <&extal_clk &usb_extal_clk>; + #clock-cells = <1>; + clock-output-names = "main", "pll0, "pll1", "pll3", + "lb", "qspi", "sdh", "sd0", "sd1", "z", + "rcan", "adsp"; + #power-domain-cells = <0>; + }; + + + - CPG/MSTP Clock Domain member device node: + + thermal@e61f0000 { + compatible = "renesas,thermal-r8a7790", "renesas,rcar-thermal"; + reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>; + interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks R8A7790_CLK_THERMAL>; + power-domains = <&cpg_clocks>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt new file mode 100644 index 000000000..83f6c6a7c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,rcar-usb2-clock-sel.txt @@ -0,0 +1,55 @@ +* Renesas R-Car USB 2.0 clock selector + +This file provides information on what the device node for the R-Car USB 2.0 +clock selector. + +If you connect an external clock to the USB_EXTAL pin only, you should set +the clock rate to "usb_extal" node only. +If you connect an oscillator to both the USB_XTAL and USB_EXTAL, this module +is not needed because this is default setting. (Of course, you can set the +clock rates to both "usb_extal" and "usb_xtal" nodes. + +Case 1: An external clock connects to R-Car SoC + +----------+ +--- R-Car ---------------------+ + |External |---|USB_EXTAL ---> all usb channels| + |clock | |USB_XTAL | + +----------+ +-------------------------------+ +In this case, we need this driver with "usb_extal" clock. + +Case 2: An oscillator connects to R-Car SoC + +----------+ +--- R-Car ---------------------+ + |Oscillator|---|USB_EXTAL -+-> all usb channels| + | |---|USB_XTAL --+ | + +----------+ +-------------------------------+ +In this case, we don't need this selector. + +Required properties: +- compatible: "renesas,r8a7795-rcar-usb2-clock-sel" if the device is a part of + an R8A7795 SoC. + "renesas,r8a7796-rcar-usb2-clock-sel" if the device if a part of + an R8A7796 SoC. + "renesas,rcar-gen3-usb2-clock-sel" for a generic R-Car Gen3 + compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: offset and length of the USB 2.0 clock selector register block. +- clocks: A list of phandles and specifier pairs. +- clock-names: Name of the clocks. + - The functional clock must be "ehci_ohci" + - The USB_EXTAL clock pin must be "usb_extal" + - The USB_XTAL clock pin must be "usb_xtal" +- #clock-cells: Must be 0 + +Example (R-Car H3): + + usb2_clksel: clock-controller@e6590630 { + compatible = "renesas,r8a7795-rcar-usb2-clock-sel", + "renesas,rcar-gen3-usb2-clock-sel"; + reg = <0 0xe6590630 0 0x02>; + clocks = <&cpg CPG_MOD 703>, <&usb_extal>, <&usb_xtal>; + clock-names = "ehci_ohci", "usb_extal", "usb_xtal"; + #clock-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt new file mode 100644 index 000000000..8ff3e2774 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,rz-cpg-clocks.txt @@ -0,0 +1,53 @@ +* Renesas RZ/A1 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the RZ/A1 SoCs. It includes the PLL, variable +CPU and GPU clocks, and several fixed ratio dividers. +The CPG also provides a Clock Domain for SoC devices, in combination with the +CPG Module Stop (MSTP) Clocks. + +Required Properties: + + - compatible: Must be one of + - "renesas,r7s72100-cpg-clocks" for the r7s72100 CPG + and "renesas,rz-cpg-clocks" as a fallback. + - reg: Base address and length of the memory resource used by the CPG + - clocks: References to possible parent clocks. Order must match clock modes + in the datasheet. For the r7s72100, this is extal, usb_x1. + - #clock-cells: Must be 1 + - clock-output-names: The names of the clocks. Supported clocks are "pll", + "i", and "g" + - #power-domain-cells: Must be 0 + +SoC devices that are part of the CPG/MSTP Clock Domain and can be power-managed +through an MSTP clock should refer to the CPG device node in their +"power-domains" property, as documented by the generic PM domain bindings in +Documentation/devicetree/bindings/power/power_domain.txt. + + +Examples +-------- + + - CPG device node: + + cpg_clocks: cpg_clocks@fcfe0000 { + #clock-cells = <1>; + compatible = "renesas,r7s72100-cpg-clocks", + "renesas,rz-cpg-clocks"; + reg = <0xfcfe0000 0x18>; + clocks = <&extal_clk>, <&usb_x1_clk>; + clock-output-names = "pll", "i", "g"; + #power-domain-cells = <0>; + }; + + + - CPG/MSTP Clock Domain member device node: + + mtu2: timer@fcff0000 { + compatible = "renesas,mtu2-r7s72100", "renesas,mtu2"; + reg = <0xfcff0000 0x400>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tgi0a"; + clocks = <&mstp3_clks R7S72100_CLK_MTU2>; + clock-names = "fck"; + power-domains = <&cpg_clocks>; + }; diff --git a/Documentation/devicetree/bindings/clock/renesas,sh73a0-cpg-clocks.txt b/Documentation/devicetree/bindings/clock/renesas,sh73a0-cpg-clocks.txt new file mode 100644 index 000000000..a8978ec94 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/renesas,sh73a0-cpg-clocks.txt @@ -0,0 +1,35 @@ +These bindings should be considered EXPERIMENTAL for now. + +* Renesas SH73A0 Clock Pulse Generator (CPG) + +The CPG generates core clocks for the SH73A0 SoC. It includes four PLLs +and several fixed ratio dividers. + +Required Properties: + + - compatible: Must be "renesas,sh73a0-cpg-clocks" + + - reg: Base address and length of the memory resource used by the CPG + + - clocks: Reference to the parent clocks ("extal1" and "extal2") + + - #clock-cells: Must be 1 + + - clock-output-names: The names of the clocks. Supported clocks are "main", + "pll0", "pll1", "pll2", "pll3", "dsi0phy", "dsi1phy", "zg", "m3", "b", + "m1", "m2", "z", "zx", and "hp". + + +Example +------- + + cpg_clocks: cpg_clocks@e6150000 { + compatible = "renesas,sh73a0-cpg-clocks"; + reg = <0 0xe6150000 0 0x10000>; + clocks = <&extal1_clk>, <&extal2_clk>; + #clock-cells = <1>; + clock-output-names = "main", "pll0", "pll1", "pll2", + "pll3", "dsi0phy", "dsi1phy", + "zg", "m3", "b", "m1", "m2", + "z", "zx", "hp"; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,px30-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,px30-cru.txt new file mode 100644 index 000000000..39f0c1ac8 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,px30-cru.txt @@ -0,0 +1,65 @@ +* Rockchip PX30 Clock and Reset Unit + +The PX30 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: PMU for CRU should be "rockchip,px30-pmu-cru" +- compatible: CRU should be "rockchip,px30-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing, pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/px30-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "i2sx_clkin" - external I2S clock - optional, + - "gmac_clkin" - external GMAC clock - optional + +Example: Clock controller node: + + pmucru: clock-controller@ff2bc000 { + compatible = "rockchip,px30-pmucru"; + reg = <0x0 0xff2bc000 0x0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + cru: clock-controller@ff2b0000 { + compatible = "rockchip,px30-cru"; + reg = <0x0 0xff2b0000 0x0 0x1000>; + rockchip,grf = <&grf>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@ff030000 { + compatible = "rockchip,px30-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff030000 0x0 0x100>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&pmucru SCLK_UART0_PMU>, <&pmucru PCLK_UART0_PMU>; + clock-names = "baudclk", "apb_pclk"; + reg-shift = <2>; + reg-io-width = <4>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt new file mode 100644 index 000000000..20df350b9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt @@ -0,0 +1,56 @@ +* Rockchip RK3036 Clock and Reset Unit + +The RK3036 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3036-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3036-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "ext_i2s" - external I2S clock - optional, + - "rmii_clkin" - external EMAC clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3036-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@20060000 { + compatible = "snps,dw-apb-uart"; + reg = <0x20060000 0x100>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt new file mode 100644 index 000000000..6f8744fd3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3128-cru.txt @@ -0,0 +1,58 @@ +* Rockchip RK3126/RK3128 Clock and Reset Unit + +The RK3126/RK3128 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3126-cru" or "rockchip,rk3128-cru" + "rockchip,rk3126-cru" - controller compatible with RK3126 SoC. + "rockchip,rk3128-cru" - controller compatible with RK3128 SoC. +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3128-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "ext_i2s" - external I2S clock - optional, + - "gmac_clkin" - external GMAC clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3128-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart2: serial@20068000 { + compatible = "rockchip,serial"; + reg = <0x20068000 0x100>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <24000000>; + clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; + clock-names = "sclk_uart", "pclk_uart"; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt new file mode 100644 index 000000000..7f368530a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3188-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3188/RK3066 Clock and Reset Unit + +The RK3188/RK3066 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3188-cru", "rockchip,rk3188a-cru" or + "rockchip,rk3066a-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3188-cru.h and +dt-bindings/clock/rk3066-cru.h headers and can be used in device tree sources. +Similar macros exist for the reset sources in these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "xin27m" - 27mhz crystal input on rk3066 - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_cif0" - external camera clock - optional, + - "ext_rmii" - external RMII clock - optional, + - "ext_jtag" - externalJTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3228-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3228-cru.txt new file mode 100644 index 000000000..f32304812 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3228-cru.txt @@ -0,0 +1,58 @@ +* Rockchip RK3228 Clock and Reset Unit + +The RK3228 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3228-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3228-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "ext_i2s" - external I2S clock - optional, + - "ext_gmac" - external GMAC clock - optional + - "ext_hsadc" - external HSADC clock - optional + - "phy_50m_out" - output clock of the pll in the mac phy + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3228-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10110000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10110000 0x100>; + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt new file mode 100644 index 000000000..8cb47c39b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3288-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3288 Clock and Reset Unit + +The RK3288 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3288-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3288-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_hsadc" - external HSADC clock - optional, + - "ext_edp_24m" - external display port clock - optional, + - "ext_vip" - external VIP clock - optional, + - "ext_isp" - external ISP clock - optional, + - "ext_jtag" - external JTAG clock - optional + +Example: Clock controller node: + + cru: cru@20000000 { + compatible = "rockchip,rk3188-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt new file mode 100644 index 000000000..904ae682e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3328-cru.txt @@ -0,0 +1,58 @@ +* Rockchip RK3328 Clock and Reset Unit + +The RK3328 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3328-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3328-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "clkin_i2s" - external I2S clock - optional, + - "gmac_clkin" - external GMAC clock - optional + - "phy_50m_out" - output clock of the pll in the mac phy + - "hdmi_phy" - output clock of the hdmi phy pll - optional + +Example: Clock controller node: + + cru: clock-controller@ff440000 { + compatible = "rockchip,rk3328-cru"; + reg = <0x0 0xff440000 0x0 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@ff120000 { + compatible = "snps,dw-apb-uart"; + reg = <0xff120000 0x100>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3368-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3368-cru.txt new file mode 100644 index 000000000..7c8bbcfed --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3368-cru.txt @@ -0,0 +1,61 @@ +* Rockchip RK3368 Clock and Reset Unit + +The RK3368 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3368-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing, pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3368-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_gmac" - external GMAC clock - optional + - "ext_hsadc" - external HSADC clock - optional, + - "ext_isp" - external ISP clock - optional, + - "ext_jtag" - external JTAG clock - optional + - "ext_vip" - external VIP clock - optional, + - "usbotg_out" - output clock of the pll in the otg phy + +Example: Clock controller node: + + cru: clock-controller@ff760000 { + compatible = "rockchip,rk3368-cru"; + reg = <0x0 0xff760000 0x0 0x1000>; + rockchip,grf = <&grf>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10124000 { + compatible = "snps,dw-apb-uart"; + reg = <0x10124000 0x400>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <1>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt new file mode 100644 index 000000000..3bc56fae9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3399-cru.txt @@ -0,0 +1,68 @@ +* Rockchip RK3399 Clock and Reset Unit + +The RK3399 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: PMU for CRU should be "rockchip,rk3399-pmucru" +- compatible: CRU should be "rockchip,rk3399-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files". + It is used for GRF muxes, if missing any muxes present in the GRF will not + be available. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3399-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "xin32k" - rtc clock - optional, + - "clkin_gmac" - external GMAC clock - optional, + - "clkin_i2s" - external I2S clock - optional, + - "pclkin_cif" - external ISP clock - optional, + - "clk_usbphy0_480m" - output clock of the pll in the usbphy0 + - "clk_usbphy1_480m" - output clock of the pll in the usbphy1 + +Example: Clock controller node: + + pmucru: pmu-clock-controller@ff750000 { + compatible = "rockchip,rk3399-pmucru"; + reg = <0x0 0xff750000 0x0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + cru: clock-controller@ff760000 { + compatible = "rockchip,rk3399-cru"; + reg = <0x0 0xff760000 0x0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@ff1a0000 { + compatible = "rockchip,rk3399-uart", "snps,dw-apb-uart"; + reg = <0x0 0xff180000 0x0 0x100>; + clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; diff --git a/Documentation/devicetree/bindings/clock/rockchip,rv1108-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rv1108-cru.txt new file mode 100644 index 000000000..161326a4f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rv1108-cru.txt @@ -0,0 +1,59 @@ +* Rockchip RV1108 Clock and Reset Unit + +The RV1108 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rv1108-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rv1108-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "ext_vip" - external VIP clock - optional + - "ext_i2s" - external I2S clock - optional + - "ext_gmac" - external GMAC clock - optional + - "hdmiphy" - external clock input derived from HDMI PHY - optional + - "usbphy" - external clock input derived from USB PHY - optional + +Example: Clock controller node: + + cru: cru@20200000 { + compatible = "rockchip,rv1108-cru"; + reg = <0x20200000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial@10230000 { + compatible = "rockchip,rv1108-uart", "snps,dw-apb-uart"; + reg = <0x10230000 0x100>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s2mps11.txt b/Documentation/devicetree/bindings/clock/samsung,s2mps11.txt new file mode 100644 index 000000000..2726c1d58 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s2mps11.txt @@ -0,0 +1,49 @@ +Binding for Samsung S2M and S5M family clock generator block +============================================================ + +This is a part of device tree bindings for S2M and S5M family multi-function +devices. +More information can be found in bindings/mfd/sec-core.txt file. + +The S2MPS11/13/15 and S5M8767 provide three(AP/CP/BT) buffered 32.768 kHz +outputs. The S2MPS14 provides two (AP/BT) buffered 32.768 KHz outputs. + +To register these as clocks with common clock framework instantiate under +main device node a sub-node named "clocks". + +It uses the common clock binding documented in: + - Documentation/devicetree/bindings/clock/clock-bindings.txt + + +Required properties of the "clocks" sub-node: + - #clock-cells: should be 1. + - compatible: Should be one of: "samsung,s2mps11-clk", "samsung,s2mps13-clk", + "samsung,s2mps14-clk", "samsung,s5m8767-clk" + The S2MPS15 uses the same compatible as S2MPS13, as both provides similar + clocks. + + +Each clock is assigned an identifier and client nodes use this identifier +to specify the clock which they consume. + Clock ID Devices + ---------------------------------------------------------- + 32KhzAP 0 S2MPS11/13/14/15, S5M8767 + 32KhzCP 1 S2MPS11/13/15, S5M8767 + 32KhzBT 2 S2MPS11/13/14/15, S5M8767 + +Include dt-bindings/clock/samsung,s2mps11.h file to use preprocessor defines +in device tree sources. + + +Example: + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + + s2m_osc: clocks { + compatible = "samsung,s2mps11-clk"; + #clock-cells = <1>; + clock-output-names = "xx", "yy", "zz"; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt new file mode 100644 index 000000000..2632d3f13 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2410-clock.txt @@ -0,0 +1,49 @@ +* Samsung S3C2410 Clock Controller + +The S3C2410 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to the s3c2410, +s3c2440 and s3c2442 SoCs in the s3c24x family. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,s3c2410-clock" - controller compatible with S3C2410 SoC. + - "samsung,s3c2440-clock" - controller compatible with S3C2440 SoC. + - "samsung,s3c2442-clock" - controller compatible with S3C2442 SoC. +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2410.h header and can be used in device +tree sources. + +External clocks: + +The xti clock used as input for the plls is generated outside the SoC. It is +expected that is are defined using standard clock bindings with a +clock-output-names value of "xti". + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2410-clock"; + reg = <0x4c000000 0x20>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2440-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt new file mode 100644 index 000000000..21a8c23e6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2412-clock.txt @@ -0,0 +1,49 @@ +* Samsung S3C2412 Clock Controller + +The S3C2412 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to the s3c2412 +and s3c2413 SoCs in the s3c24x family. + +Required Properties: + +- compatible: should be "samsung,s3c2412-clock" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2412.h header and can be used in device +tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xti" - crystal input - required, + - "ext" - external clock source - optional, + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2412-clock"; + reg = <0x4c000000 0x20>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2412-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2", "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt new file mode 100644 index 000000000..985c0f574 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c2443-clock.txt @@ -0,0 +1,55 @@ +* Samsung S3C2443 Clock Controller + +The S3C2443 clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to all SoCs in +the s3c24x family starting with the s3c2443. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,s3c2416-clock" - controller compatible with S3C2416 SoC. + - "samsung,s3c2443-clock" - controller compatible with S3C2443 SoC. + - "samsung,s3c2450-clock" - controller compatible with S3C2450 SoC. +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular SoC. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s3c2443.h header and can be used in device +tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xti" - crystal input - required, + - "ext" - external clock source - optional, + - "ext_i2s" - external I2S clock - optional, + - "ext_uart" - external uart clock - optional, + +Example: Clock controller node: + + clocks: clock-controller@4c000000 { + compatible = "samsung,s3c2416-clock"; + reg = <0x4c000000 0x40>; + #clock-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + serial@50004000 { + compatible = "samsung,s3c2440-uart"; + reg = <0x50004000 0x4000>; + interrupts = <1 23 3 4>, <1 23 4 4>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clocks PCLK_UART0>, <&clocks PCLK_UART0>, + <&clocks SCLK_UART>; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s3c64xx-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s3c64xx-clock.txt new file mode 100644 index 000000000..872ee8e0f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s3c64xx-clock.txt @@ -0,0 +1,76 @@ +* Samsung S3C64xx Clock Controller + +The S3C64xx clock controller generates and supplies clock to various controllers +within the SoC. The clock binding described here is applicable to all SoCs in +the S3C64xx family. + +Required Properties: + +- compatible: should be one of the following. + - "samsung,s3c6400-clock" - controller compatible with S3C6400 SoC. + - "samsung,s3c6410-clock" - controller compatible with S3C6410 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Some of the clocks are available only +on a particular S3C64xx SoC and this is specified where applicable. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/samsung,s3c64xx-clock.h header and can be used in device +tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "fin_pll" - PLL input clock (xtal/extclk) - required, + - "xusbxti" - USB xtal - required, + - "iiscdclk0" - I2S0 codec clock - optional, + - "iiscdclk1" - I2S1 codec clock - optional, + - "iiscdclk2" - I2S2 codec clock - optional, + - "pcmcdclk0" - PCM0 codec clock - optional, + - "pcmcdclk1" - PCM1 codec clock - optional, only S3C6410. + +Example: Clock controller node: + + clock: clock-controller@7e00f000 { + compatible = "samsung,s3c6410-clock"; + reg = <0x7e00f000 0x1000>; + #clock-cells = <1>; + }; + +Example: Required external clocks: + + fin_pll: clock-fin-pll { + compatible = "fixed-clock"; + clock-output-names = "fin_pll"; + clock-frequency = <12000000>; + #clock-cells = <0>; + }; + + xusbxti: clock-xusbxti { + compatible = "fixed-clock"; + clock-output-names = "xusbxti"; + clock-frequency = <48000000>; + #clock-cells = <0>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + uart0: serial@7f005000 { + compatible = "samsung,s3c6400-uart"; + reg = <0x7f005000 0x100>; + interrupt-parent = <&vic1>; + interrupts = <5>; + clock-names = "uart", "clk_uart_baud2", + "clk_uart_baud3"; + clocks = <&clock PCLK_UART0>, <&clocks PCLK_UART0>, + <&clock SCLK_UART>; + }; diff --git a/Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt b/Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt new file mode 100644 index 000000000..15b48e20a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/samsung,s5pv210-clock.txt @@ -0,0 +1,77 @@ +* Samsung S5P6442/S5PC110/S5PV210 Clock Controller + +Samsung S5P6442, S5PC110 and S5PV210 SoCs contain integrated clock +controller, which generates and supplies clock to various controllers +within the SoC. + +Required Properties: + +- compatible: should be one of following: + - "samsung,s5pv210-clock" : for clock controller of Samsung + S5PC110/S5PV210 SoCs, + - "samsung,s5p6442-clock" : for clock controller of Samsung + S5P6442 SoC. + +- reg: physical base address of the controller and length of memory mapped + region. + +- #clock-cells: should be 1. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/s5pv210.h header and can be used in device tree sources. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xxti": external crystal oscillator connected to XXTI and XXTO pins of +the SoC, + - "xusbxti": external crystal oscillator connected to XUSBXTI and XUSBXTO +pins of the SoC, + +A subset of above clocks available on given board shall be specified in +board device tree, including the system base clock, as selected by XOM[0] +pin of the SoC. Refer to generic fixed rate clock bindings +documentation[1] for more information how to specify these clocks. + +[1] Documentation/devicetree/bindings/clock/fixed-clock.txt + +Example: Clock controller node: + + clock: clock-controller@7e00f000 { + compatible = "samsung,s5pv210-clock"; + reg = <0x7e00f000 0x1000>; + #clock-cells = <1>; + }; + +Example: Required external clocks: + + xxti: clock-xxti { + compatible = "fixed-clock"; + clock-output-names = "xxti"; + clock-frequency = <24000000>; + #clock-cells = <0>; + }; + + xusbxti: clock-xusbxti { + compatible = "fixed-clock"; + clock-output-names = "xusbxti"; + clock-frequency = <24000000>; + #clock-cells = <0>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller (refer to the standard clock bindings for information about + "clocks" and "clock-names" properties): + + uart0: serial@e2900000 { + compatible = "samsung,s5pv210-uart"; + reg = <0xe2900000 0x400>; + interrupt-parent = <&vic1>; + interrupts = <10>; + clock-names = "uart", "clk_uart_baud0", + "clk_uart_baud1"; + clocks = <&clocks UART0>, <&clocks UART0>, + <&clocks SCLK_UART0>; + }; diff --git a/Documentation/devicetree/bindings/clock/silabs,si514.txt b/Documentation/devicetree/bindings/clock/silabs,si514.txt new file mode 100644 index 000000000..ea1a9dbc6 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si514.txt @@ -0,0 +1,24 @@ +Binding for Silicon Labs 514 programmable I2C clock generator. + +Reference +This binding uses the common clock binding[1]. Details about the device can be +found in the datasheet[2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Si514 datasheet + http://www.silabs.com/Support%20Documents/TechnicalDocs/si514.pdf + +Required properties: + - compatible: Shall be "silabs,si514" + - reg: I2C device address. + - #clock-cells: From common clock bindings: Shall be 0. + +Optional properties: + - clock-output-names: From common clock bindings. Recommended to be "si514". + +Example: + si514: clock-generator@55 { + reg = <0x55>; + #clock-cells = <0>; + compatible = "silabs,si514"; + }; diff --git a/Documentation/devicetree/bindings/clock/silabs,si5351.txt b/Documentation/devicetree/bindings/clock/silabs,si5351.txt new file mode 100644 index 000000000..f00191cad --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si5351.txt @@ -0,0 +1,126 @@ +Binding for Silicon Labs Si5351a/b/c programmable i2c clock generator. + +Reference +[1] Si5351A/B/C Data Sheet + http://www.silabs.com/Support%20Documents/TechnicalDocs/Si5351.pdf + +The Si5351a/b/c are programmable i2c clock generators with up to 8 output +clocks. Si5351a also has a reduced pin-count package (MSOP10) where only +3 output clocks are accessible. The internal structure of the clock +generators can be found in [1]. + +==I2C device node== + +Required properties: +- compatible: shall be one of the following: + "silabs,si5351a" - Si5351a, QFN20 package + "silabs,si5351a-msop" - Si5351a, MSOP10 package + "silabs,si5351b" - Si5351b, QFN20 package + "silabs,si5351c" - Si5351c, QFN20 package +- reg: i2c device address, shall be 0x60 or 0x61. +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: from common clock binding; list of parent clock + handles, shall be xtal reference clock or xtal and clkin for + si5351c only. Corresponding clock input names are "xtal" and + "clkin" respectively. +- #address-cells: shall be set to 1. +- #size-cells: shall be set to 0. + +Optional properties: +- silabs,pll-source: pair of (number, source) for each pll. Allows + to overwrite clock source of pll A (number=0) or B (number=1). + +==Child nodes== + +Each of the clock outputs can be overwritten individually by +using a child node to the I2C device node. If a child node for a clock +output is not set, the eeprom configuration is not overwritten. + +Required child node properties: +- reg: number of clock output. + +Optional child node properties: +- silabs,clock-source: source clock of the output divider stage N, shall be + 0 = multisynth N + 1 = multisynth 0 for output clocks 0-3, else multisynth4 + 2 = xtal + 3 = clkin (si5351c only) +- silabs,drive-strength: output drive strength in mA, shall be one of {2,4,6,8}. +- silabs,multisynth-source: source pll A(0) or B(1) of corresponding multisynth + divider. +- silabs,pll-master: boolean, multisynth can change pll frequency. +- silabs,pll-reset: boolean, clock output can reset its pll. +- silabs,disable-state : clock output disable state, shall be + 0 = clock output is driven LOW when disabled + 1 = clock output is driven HIGH when disabled + 2 = clock output is FLOATING (HIGH-Z) when disabled + 3 = clock output is NEVER disabled + +==Example== + +/* 25MHz reference crystal */ +ref25: ref25M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; +}; + +i2c-master-node { + + /* Si5351a msop10 i2c clock generator */ + si5351a: clock-generator@60 { + compatible = "silabs,si5351a-msop"; + reg = <0x60>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + + /* connect xtal input to 25MHz reference */ + clocks = <&ref25>; + clock-names = "xtal"; + + /* connect xtal input as source of pll0 and pll1 */ + silabs,pll-source = <0 0>, <1 0>; + + /* + * overwrite clkout0 configuration with: + * - 8mA output drive strength + * - pll0 as clock source of multisynth0 + * - multisynth0 as clock source of output divider + * - multisynth0 can change pll0 + * - set initial clock frequency of 74.25MHz + */ + clkout0 { + reg = <0>; + silabs,drive-strength = <8>; + silabs,multisynth-source = <0>; + silabs,clock-source = <0>; + silabs,pll-master; + clock-frequency = <74250000>; + }; + + /* + * overwrite clkout1 configuration with: + * - 4mA output drive strength + * - pll1 as clock source of multisynth1 + * - multisynth1 as clock source of output divider + * - multisynth1 can change pll1 + */ + clkout1 { + reg = <1>; + silabs,drive-strength = <4>; + silabs,multisynth-source = <1>; + silabs,clock-source = <0>; + pll-master; + }; + + /* + * overwrite clkout2 configuration with: + * - xtal as clock source of output divider + */ + clkout2 { + reg = <2>; + silabs,clock-source = <2>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/silabs,si544.txt b/Documentation/devicetree/bindings/clock/silabs,si544.txt new file mode 100644 index 000000000..b86535b80 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si544.txt @@ -0,0 +1,25 @@ +Binding for Silicon Labs 544 programmable I2C clock generator. + +Reference +This binding uses the common clock binding[1]. Details about the device can be +found in the datasheet[2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Si544 datasheet + https://www.silabs.com/documents/public/data-sheets/si544-datasheet.pdf + +Required properties: + - compatible: One of "silabs,si514a", "silabs,si514b" "silabs,si514c" according + to the speed grade of the chip. + - reg: I2C device address. + - #clock-cells: From common clock bindings: Shall be 0. + +Optional properties: + - clock-output-names: From common clock bindings. Recommended to be "si544". + +Example: + si544: clock-controller@55 { + reg = <0x55>; + #clock-cells = <0>; + compatible = "silabs,si544b"; + }; diff --git a/Documentation/devicetree/bindings/clock/silabs,si570.txt b/Documentation/devicetree/bindings/clock/silabs,si570.txt new file mode 100644 index 000000000..c09f21e1d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/silabs,si570.txt @@ -0,0 +1,39 @@ +Binding for Silicon Labs 570, 571, 598 and 599 programmable +I2C clock generators. + +Reference +This binding uses the common clock binding[1]. Details about the devices can be +found in the data sheets[2][3]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Si570/571 Data Sheet + http://www.silabs.com/Support%20Documents/TechnicalDocs/si570.pdf +[3] Si598/599 Data Sheet + http://www.silabs.com/Support%20Documents/TechnicalDocs/si598-99.pdf + +Required properties: + - compatible: Shall be one of "silabs,si570", "silabs,si571", + "silabs,si598", "silabs,si599" + - reg: I2C device address. + - #clock-cells: From common clock bindings: Shall be 0. + - factory-fout: Factory set default frequency. This frequency is part specific. + The correct frequency for the part used has to be provided in + order to generate the correct output frequencies. For more + details, please refer to the data sheet. + - temperature-stability: Temperature stability of the device in PPM. Should be + one of: 7, 20, 50 or 100. + +Optional properties: + - clock-output-names: From common clock bindings. Recommended to be "si570". + - clock-frequency: Output frequency to generate. This defines the output + frequency set during boot. It can be reprogrammed during + runtime through the common clock framework. + +Example: + si570: clock-generator@5d { + #clock-cells = <0>; + compatible = "silabs,si570"; + temperature-stability = <50>; + reg = <0x5d>; + factory-fout = <156250000>; + }; diff --git a/Documentation/devicetree/bindings/clock/snps,hsdk-pll-clock.txt b/Documentation/devicetree/bindings/clock/snps,hsdk-pll-clock.txt new file mode 100644 index 000000000..c56c7553c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/snps,hsdk-pll-clock.txt @@ -0,0 +1,28 @@ +Binding for the HSDK Generic PLL clock + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: should be "snps,hsdk-<name>-pll-clock" + "snps,hsdk-core-pll-clock" + "snps,hsdk-gp-pll-clock" + "snps,hsdk-hdmi-pll-clock" +- reg : should contain base register location and length. +- clocks: shall be the input parent clock phandle for the PLL. +- #clock-cells: from common clock binding; Should always be set to 0. + +Example: + input_clk: input-clk { + clock-frequency = <33333333>; + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + cpu_clk: cpu-clk@0 { + compatible = "snps,hsdk-core-pll-clock"; + reg = <0x00 0x10>; + #clock-cells = <0>; + clocks = <&input_clk>; + }; diff --git a/Documentation/devicetree/bindings/clock/snps,pll-clock.txt b/Documentation/devicetree/bindings/clock/snps,pll-clock.txt new file mode 100644 index 000000000..11fe48766 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/snps,pll-clock.txt @@ -0,0 +1,28 @@ +Binding for the AXS10X Generic PLL clock + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible: should be "snps,axs10x-<name>-pll-clock" + "snps,axs10x-arc-pll-clock" + "snps,axs10x-pgu-pll-clock" +- reg: should always contain 2 pairs address - length: first for PLL config +registers and second for corresponding LOCK CGU register. +- clocks: shall be the input parent clock phandle for the PLL. +- #clock-cells: from common clock binding; Should always be set to 0. + +Example: + input-clk: input-clk { + clock-frequency = <33333333>; + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + core-clk: core-clk@80 { + compatible = "snps,axs10x-arc-pll-clock"; + reg = <0x80 0x10>, <0x100 0x10>; + #clock-cells = <0>; + clocks = <&input-clk>; + }; diff --git a/Documentation/devicetree/bindings/clock/sprd.txt b/Documentation/devicetree/bindings/clock/sprd.txt new file mode 100644 index 000000000..e9d179e88 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sprd.txt @@ -0,0 +1,63 @@ +Spreadtrum Clock Binding +------------------------ + +Required properties: +- compatible: should contain the following compatible strings: + - "sprd,sc9860-pmu-gate" + - "sprd,sc9860-pll" + - "sprd,sc9860-ap-clk" + - "sprd,sc9860-aon-prediv" + - "sprd,sc9860-apahb-gate" + - "sprd,sc9860-aon-gate" + - "sprd,sc9860-aonsecure-clk" + - "sprd,sc9860-agcp-gate" + - "sprd,sc9860-gpu-clk" + - "sprd,sc9860-vsp-clk" + - "sprd,sc9860-vsp-gate" + - "sprd,sc9860-cam-clk" + - "sprd,sc9860-cam-gate" + - "sprd,sc9860-disp-clk" + - "sprd,sc9860-disp-gate" + - "sprd,sc9860-apapb-gate" + +- #clock-cells: must be 1 + +- clocks : Should be the input parent clock(s) phandle for the clock, this + property here just simply shows which clock group the clocks' + parents are in, since each clk node would represent many clocks + which are defined in the driver. The detailed dependency + relationship (i.e. how many parents and which are the parents) + are implemented in driver code. + +Optional properties: + +- reg: Contain the registers base address and length. It must be configured + only if no 'sprd,syscon' under the node. + +- sprd,syscon: phandle to the syscon which is in the same address area with + the clock, and so we can get regmap for the clocks from the + syscon device. + +Example: + + pmu_gate: pmu-gate { + compatible = "sprd,sc9860-pmu-gate"; + sprd,syscon = <&pmu_regs>; + clocks = <&ext_26m>; + #clock-cells = <1>; + }; + + pll: pll { + compatible = "sprd,sc9860-pll"; + sprd,syscon = <&ana_regs>; + clocks = <&pmu_gate 0>; + #clock-cells = <1>; + }; + + ap_clk: clock-controller@20000000 { + compatible = "sprd,sc9860-ap-clk"; + reg = <0 0x20000000 0 0x400>; + clocks = <&ext_26m>, <&pll 0>, + <&pmu_gate 0>; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/st,nomadik.txt b/Documentation/devicetree/bindings/clock/st,nomadik.txt new file mode 100644 index 000000000..40e0cf1f7 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st,nomadik.txt @@ -0,0 +1,104 @@ +ST Microelectronics Nomadik SRC System Reset and Control + +This binding uses the common clock binding: +Documentation/devicetree/bindings/clock/clock-bindings.txt + +The Nomadik SRC controller is responsible of controlling chrystals, +PLLs and clock gates. + +Required properties for the SRC node: +- compatible: must be "stericsson,nomadik-src" +- reg: must contain the SRC register base and size + +Optional properties for the SRC node: +- disable-sxtalo: if present this will disable the SXTALO + i.e. the driver output for the slow 32kHz chrystal, if the + board has its own circuitry for providing this oscillator +- disable-mxtal: if present this will disable the MXTALO, + i.e. the driver output for the main (~19.2 MHz) chrystal, + if the board has its own circuitry for providing this + oscillator + + +PLL nodes: these nodes represent the two PLLs on the system, +which should both have the main chrystal, represented as a +fixed frequency clock, as parent. + +Required properties for the two PLL nodes: +- compatible: must be "st,nomadik-pll-clock" +- clock-cells: must be 0 +- clock-id: must be 1 or 2 for PLL1 and PLL2 respectively +- clocks: this clock will have main chrystal as parent + + +HCLK nodes: these represent the clock gates on individual +lines from the HCLK clock tree and the gate for individual +lines from the PCLK clock tree. + +Requires properties for the HCLK nodes: +- compatible: must be "st,nomadik-hclk-clock" +- clock-cells: must be 0 +- clock-id: must be the clock ID from 0 to 63 according to + this table: + + 0: HCLKDMA0 + 1: HCLKSMC + 2: HCLKSDRAM + 3: HCLKDMA1 + 4: HCLKCLCD + 5: PCLKIRDA + 6: PCLKSSP + 7: PCLKUART0 + 8: PCLKSDI + 9: PCLKI2C0 + 10: PCLKI2C1 + 11: PCLKUART1 + 12: PCLMSP0 + 13: HCLKUSB + 14: HCLKDIF + 15: HCLKSAA + 16: HCLKSVA + 17: PCLKHSI + 18: PCLKXTI + 19: PCLKUART2 + 20: PCLKMSP1 + 21: PCLKMSP2 + 22: PCLKOWM + 23: HCLKHPI + 24: PCLKSKE + 25: PCLKHSEM + 26: HCLK3D + 27: HCLKHASH + 28: HCLKCRYP + 29: PCLKMSHC + 30: HCLKUSBM + 31: HCLKRNG + (32, 33, 34, 35 RESERVED) + 36: CLDCLK + 37: IRDACLK + 38: SSPICLK + 39: UART0CLK + 40: SDICLK + 41: I2C0CLK + 42: I2C1CLK + 43: UART1CLK + 44: MSPCLK0 + 45: USBCLK + 46: DIFCLK + 47: IPI2CCLK + 48: IPBMCCLK + 49: HSICLKRX + 50: HSICLKTX + 51: UART2CLK + 52: MSPCLK1 + 53: MSPCLK2 + 54: OWMCLK + (55 RESERVED) + 56: SKECLK + (57 RESERVED) + 58: 3DCLK + 59: PCLKMSP3 + 60: MSPCLK3 + 61: MSHCCLK + 62: USBMCLK + 63: RNGCCLK diff --git a/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt new file mode 100644 index 000000000..b240121d2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st,stm32-rcc.txt @@ -0,0 +1,132 @@ +STMicroelectronics STM32 Reset and Clock Controller +=================================================== + +The RCC IP is both a reset and a clock controller. + +Please refer to clock-bindings.txt for common clock controller binding usage. +Please also refer to reset.txt for common reset controller binding usage. + +Required properties: +- compatible: Should be: + "st,stm32f42xx-rcc" + "st,stm32f469-rcc" + "st,stm32f746-rcc" +- reg: should be register base and length as documented in the + datasheet +- #reset-cells: 1, see below +- #clock-cells: 2, device nodes should specify the clock in their "clocks" + property, containing a phandle to the clock device node, an index selecting + between gated clocks and other clocks and an index specifying the clock to + use. +- clocks: External oscillator clock phandle + - high speed external clock signal (HSE) + - external I2S clock (I2S_CKIN) + +Example: + + rcc: rcc@40023800 { + #reset-cells = <1>; + #clock-cells = <2> + compatible = "st,stm32f42xx-rcc", "st,stm32-rcc"; + reg = <0x40023800 0x400>; + clocks = <&clk_hse>, <&clk_i2s_ckin>; + }; + +Specifying gated clocks +======================= + +The primary index must be set to 0. + +The secondary index is the bit number within the RCC register bank, starting +from the first RCC clock enable register (RCC_AHB1ENR, address offset 0x30). + +It is calculated as: index = register_offset / 4 * 32 + bit_offset. +Where bit_offset is the bit offset within the register (LSB is 0, MSB is 31). + +To simplify the usage and to share bit definition with the reset and clock +drivers of the RCC IP, macros are available to generate the index in +human-readble format. + +For STM32F4 series, the macro are available here: + - include/dt-bindings/mfd/stm32f4-rcc.h + +Example: + + /* Gated clock, AHB1 bit 0 (GPIOA) */ + ... { + clocks = <&rcc 0 STM32F4_AHB1_CLOCK(GPIOA)> + }; + + /* Gated clock, AHB2 bit 4 (CRYP) */ + ... { + clocks = <&rcc 0 STM32F4_AHB2_CLOCK(CRYP)> + }; + +Specifying other clocks +======================= + +The primary index must be set to 1. + +The secondary index is bound with the following magic numbers: + + 0 SYSTICK + 1 FCLK + 2 CLK_LSI (low-power clock source) + 3 CLK_LSE (generated from a 32.768 kHz low-speed external + crystal or ceramic resonator) + 4 CLK_HSE_RTC (HSE division factor for RTC clock) + 5 CLK_RTC (real-time clock) + 6 PLL_VCO_I2S (vco frequency of I2S pll) + 7 PLL_VCO_SAI (vco frequency of SAI pll) + 8 CLK_LCD (LCD-TFT) + 9 CLK_I2S (I2S clocks) + 10 CLK_SAI1 (audio clocks) + 11 CLK_SAI2 + 12 CLK_I2SQ_PDIV (post divisor of pll i2s q divisor) + 13 CLK_SAIQ_PDIV (post divisor of pll sai q divisor) + + 14 CLK_HSI (Internal ocscillator clock) + 15 CLK_SYSCLK (System Clock) + 16 CLK_HDMI_CEC (HDMI-CEC clock) + 17 CLK_SPDIF (SPDIF-Rx clock) + 18 CLK_USART1 (U(s)arts clocks) + 19 CLK_USART2 + 20 CLK_USART3 + 21 CLK_UART4 + 22 CLK_UART5 + 23 CLK_USART6 + 24 CLK_UART7 + 25 CLK_UART8 + 26 CLK_I2C1 (I2S clocks) + 27 CLK_I2C2 + 28 CLK_I2C3 + 29 CLK_I2C4 + 30 CLK_LPTIMER (LPTimer1 clock) +) + +Example: + + /* Misc clock, FCLK */ + ... { + clocks = <&rcc 1 STM32F4_APB1_CLOCK(TIM2)> + }; + + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the reset device node and an index specifying +which channel to use. +The index is the bit number within the RCC registers bank, starting from RCC +base address. +It is calculated as: index = register_offset / 4 * 32 + bit_offset. +Where bit_offset is the bit offset within the register. +For example, for CRC reset: + crc = AHB1RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x10 / 4 * 32 + 12 = 140 + +example: + + timer2 { + resets = <&rcc STM32F4_APB1_RESET(TIM2)>; + }; diff --git a/Documentation/devicetree/bindings/clock/st,stm32h7-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32h7-rcc.txt new file mode 100644 index 000000000..cac24ee10 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st,stm32h7-rcc.txt @@ -0,0 +1,71 @@ +STMicroelectronics STM32H7 Reset and Clock Controller +===================================================== + +The RCC IP is both a reset and a clock controller. + +Please refer to clock-bindings.txt for common clock controller binding usage. +Please also refer to reset.txt for common reset controller binding usage. + +Required properties: +- compatible: Should be: + "st,stm32h743-rcc" + +- reg: should be register base and length as documented in the + datasheet + +- #reset-cells: 1, see below + +- #clock-cells : from common clock binding; shall be set to 1 + +- clocks: External oscillator clock phandle + - high speed external clock signal (HSE) + - low speed external clock signal (LSE) + - external I2S clock (I2S_CKIN) + +Optional properties: +- st,syscfg: phandle for pwrcfg, mandatory to disable/enable backup domain + write protection (RTC clock). + +Example: + + rcc: reset-clock-controller@58024400 { + compatible = "st,stm32h743-rcc", "st,stm32-rcc"; + reg = <0x58024400 0x400>; + #reset-cells = <1>; + #clock-cells = <1>; + clocks = <&clk_hse>, <&clk_lse>, <&clk_i2s_ckin>; + + st,syscfg = <&pwrcfg>; +}; + +The peripheral clock consumer should specify the desired clock by +having the clock ID in its "clocks" phandle cell. + +Example: + + timer5: timer@40000c00 { + compatible = "st,stm32-timer"; + reg = <0x40000c00 0x400>; + interrupts = <50>; + clocks = <&rcc TIM5_CK>; + }; + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the reset device node and an index specifying +which channel to use. +The index is the bit number within the RCC registers bank, starting from RCC +base address. +It is calculated as: index = register_offset / 4 * 32 + bit_offset. +Where bit_offset is the bit offset within the register. + +For example, for CRC reset: + crc = AHB4RSTR_offset / 4 * 32 + CRCRST_bit_offset = 0x88 / 4 * 32 + 19 = 1107 + +Example: + + timer2 { + resets = <&rcc STM32H7_APB1L_RESET(TIM2)>; + }; diff --git a/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt b/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt new file mode 100644 index 000000000..fb9495ea5 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st,stm32mp1-rcc.txt @@ -0,0 +1,60 @@ +STMicroelectronics STM32 Peripheral Reset Clock Controller +========================================================== + +The RCC IP is both a reset and a clock controller. + +RCC makes also power management (resume/supend and wakeup interrupt). + +Please also refer to reset.txt for common reset controller binding usage. + +Please also refer to clock-bindings.txt for common clock controller +binding usage. + + +Required properties: +- compatible: "st,stm32mp1-rcc", "syscon" +- reg: should be register base and length as documented in the datasheet +- #clock-cells: 1, device nodes should specify the clock in their + "clocks" property, containing a phandle to the clock device node, + an index specifying the clock to use. +- #reset-cells: Shall be 1 +- interrupts: Should contain a general interrupt line and a interrupt line + to the wake-up of processor (CSTOP). + +Example: + rcc: rcc@50000000 { + compatible = "st,stm32mp1-rcc", "syscon"; + reg = <0x50000000 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + interrupts = <GIC_SPI 5 IRQ_TYPE_NONE>, + <GIC_SPI 145 IRQ_TYPE_NONE>; + }; + +Specifying clocks +================= + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/stm32mp1-clks.h header and can be used in device +tree sources. + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the reset device node and an index specifying +which channel to use. +The index is the bit number within the RCC registers bank, starting from RCC +base address. +It is calculated as: index = register_offset / 4 * 32 + bit_offset. +Where bit_offset is the bit offset within the register. + +For example on STM32MP1, for LTDC reset: + ltdc = APB4_RSTSETR_offset / 4 * 32 + LTDC_bit_offset + = 0x180 / 4 * 32 + 0 = 3072 + +The list of valid indices for STM32MP1 is available in: +include/dt-bindings/reset-controller/stm32mp1-resets.h + +This file implements defines like: +#define LTDC_R 3072 diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt new file mode 100644 index 000000000..9a46cb1d7 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt @@ -0,0 +1,32 @@ +Binding for a ST multiplexed clock driver. + +This binding supports only simple indexed multiplexers, it does not +support table based parent index to hardware value translations. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: + +- compatible : shall be: + "st,stih407-clkgen-a9-mux" + +- #clock-cells : from common clock binding; shall be set to 0. + +- reg : A Base address and length of the register set. + +- clocks : from common clock binding + +Example: + + clk_m_a9: clk-m-a9@92b0000 { + #clock-cells = <0>; + compatible = "st,stih407-clkgen-a9-mux"; + reg = <0x92b0000 0x10000>; + + clocks = <&clockgen_a9_pll 0>, + <&clockgen_a9_pll 0>, + <&clk_s_c0_flexgen 13>, + <&clk_m_a9_ext2f_div2>; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt new file mode 100644 index 000000000..f207053e0 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt @@ -0,0 +1,37 @@ +Binding for a ST pll clock driver. + +This binding uses the common clock binding[1]. +Base address is located to the parent node. See clock binding[2] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt + +Required properties: + +- compatible : shall be: + "st,clkgen-pll0" + "st,clkgen-pll1" + "st,stih407-clkgen-plla9" + "st,stih418-clkgen-plla9" + +- #clock-cells : From common clock binding; shall be set to 1. + +- clocks : From common clock binding + +- clock-output-names : From common clock binding. + +Example: + + clockgen-a9@92b0000 { + compatible = "st,clkgen-c32"; + reg = <0x92b0000 0xffff>; + + clockgen_a9_pll: clockgen-a9-pll { + #clock-cells = <1>; + compatible = "st,stih407-clkgen-plla9"; + + clocks = <&clk_sysin>; + + clock-output-names = "clockgen-a9-pll-odf"; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt new file mode 100644 index 000000000..45ac19bfa --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt @@ -0,0 +1,68 @@ +Binding for a Clockgen hardware block found on +certain STMicroelectronics consumer electronics SoC devices. + +A Clockgen node can contain pll, diviser or multiplexer nodes. + +We will find only the base address of the Clockgen, this base +address is common of all subnode. + + clockgen_node { + reg = <>; + + pll_node { + ... + }; + + quadfs_node { + ... + }; + + mux_node { + ... + }; + + flexgen_node { + ... + }; + ... + }; + +This binding uses the common clock binding[1]. +Each subnode should use the binding described in [2]..[7] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[3] Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt +[4] Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt +[7] Documentation/devicetree/bindings/clock/st/st,quadfs.txt +[8] Documentation/devicetree/bindings/clock/st/st,flexgen.txt + + +Required properties: +- reg : A Base address and length of the register set. + +Example: + + clockgen-a@90ff000 { + compatible = "st,clkgen-c32"; + reg = <0x90ff000 0x1000>; + + clk_s_a0_pll: clk-s-a0-pll { + #clock-cells = <1>; + compatible = "st,clkgen-pll0"; + + clocks = <&clk_sysin>; + + clock-output-names = "clk-s-a0-pll-ofd-0"; + }; + + clk_s_a0_flexgen: clk-s-a0-flexgen { + compatible = "st,flexgen"; + + #clock-cells = <1>; + + clocks = <&clk_s_a0_pll 0>, + <&clk_sysin>; + + clock-output-names = "clk-ic-lmi0"; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt new file mode 100644 index 000000000..7ff77fc57 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt @@ -0,0 +1,123 @@ +Binding for a type of flexgen structure found on certain +STMicroelectronics consumer electronics SoC devices + +This structure includes: +- a clock cross bar (represented by a mux element) +- a pre and final dividers (represented by a divider and gate elements) + +Flexgen structure is a part of Clockgen[1]. + +Please find an example below: + + Clockgen block diagram + ------------------------------------------------------------------- + | Flexgen structure | + | --------------------------------------------- | + | | ------- -------- -------- | | +clk_sysin | | | | | | | | | +---|-----------------|-->| | | | | | | | + | | | | | | | | | | | + | | ------- | | | |Pre | |Final | | | + | | |PLL0 | | | | |Dividers| |Dividers| | | + | |->| | | | | | x32 | | x32 | | | + | | | odf_0|----|-->| | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | ------- | | | | | | | | | + | | | | | | | | | | | + | | ------- | | Clock | | | | | | | + | | |PLL1 | | | | | | | | | | + | |->| | | | Cross | | | | | | | + | | | odf_0|----|-->| | | | | | CLK_DIV[31:0] + | | | | | | Bar |====>| |====>| |===|=========> + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | ------- | | | | | | | | | + | | | | | | | | | | | + | | ------- | | | | | | | | | + | | |QUADFS | | | | | | | | | | + | |->| ch0|----|-->| | | | | | | | + | | | | | | | | | | | | + | | ch1|----|-->| | | | | | | | + | | | | | | | | | | | | + | | ch2|----|-->| | | DIV | | DIV | | | + | | | | | | | 1 to | | 1 to | | | + | | ch3|----|-->| | | 1024 | | 64 | | | + | ------- | | | | | | | | | + | | ------- -------- -------- | | + | -------------------------------------------- | + | | + ------------------------------------------------------------------- + +This binding uses the common clock binding[2]. + +[1] Documentation/devicetree/bindings/clock/st/st,clkgen.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be: + "st,flexgen" + "st,flexgen-audio", "st,flexgen" (enable clock propagation on parent for + audio use case) + "st,flexgen-video", "st,flexgen" (enable clock propagation on parent + and activate synchronous mode) + +- #clock-cells : from common clock binding; shall be set to 1 (multiple clock + outputs). + +- clocks : must be set to the parent's phandle. it's could be output clocks of + a quadsfs or/and a pll or/and clk_sysin (up to 7 clocks) + +- clock-output-names : List of strings used to name the clock outputs. + +Example: + + clk_s_c0_flexgen: clk-s-c0-flexgen { + + #clock-cells = <1>; + compatible = "st,flexgen"; + + clocks = <&clk_s_c0_pll0 0>, + <&clk_s_c0_pll1 0>, + <&clk_s_c0_quadfs 0>, + <&clk_s_c0_quadfs 1>, + <&clk_s_c0_quadfs 2>, + <&clk_s_c0_quadfs 3>, + <&clk_sysin>; + + clock-output-names = "clk-icn-gpu", + "clk-fdma", + "clk-nand", + "clk-hva", + "clk-proc-stfe", + "clk-proc-tp", + "clk-rx-icn-dmu", + "clk-rx-icn-hva", + "clk-icn-cpu", + "clk-tx-icn-dmu", + "clk-mmc-0", + "clk-mmc-1", + "clk-jpegdec", + "clk-ext2fa9", + "clk-ic-bdisp-0", + "clk-ic-bdisp-1", + "clk-pp-dmu", + "clk-vid-dmu", + "clk-dss-lpc", + "clk-st231-aud-0", + "clk-st231-gp-1", + "clk-st231-dmu", + "clk-icn-lmi", + "clk-tx-icn-disp-1", + "clk-icn-sbc", + "clk-stfe-frc2", + "clk-eth-phy", + "clk-eth-ref-phyclk", + "clk-flash-promip", + "clk-main-disp", + "clk-aux-disp", + "clk-compo-dvp"; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt new file mode 100644 index 000000000..d93d49342 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt @@ -0,0 +1,45 @@ +Binding for a type of quad channel digital frequency synthesizer found on +certain STMicroelectronics consumer electronics SoC devices. + +This version contains a programmable PLL which can generate up to 216, 432 +or 660MHz (from a 30MHz oscillator input) as the input to the digital +synthesizers. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be: + "st,quadfs" + "st,quadfs-pll" + + +- #clock-cells : from common clock binding; shall be set to 1. + +- reg : A Base address and length of the register set. + +- clocks : from common clock binding + +- clock-output-names : From common clock binding. The block has 4 + clock outputs but not all of them in a specific instance + have to be used in the SoC. If a clock name is left as + an empty string then no clock will be created for the + output associated with that string index. If fewer than + 4 strings are provided then no clocks will be created + for the remaining outputs. + +Example: + + clk_s_c0_quadfs: clk-s-c0-quadfs@9103000 { + #clock-cells = <1>; + compatible = "st,quadfs-pll"; + reg = <0x9103000 0x1000>; + + clocks = <&clk_sysin>; + + clock-output-names = "clk-s-c0-fs0-ch0", + "clk-s-c0-fs0-ch1", + "clk-s-c0-fs0-ch2", + "clk-s-c0-fs0-ch3"; + }; diff --git a/Documentation/devicetree/bindings/clock/ste-u300-syscon-clock.txt b/Documentation/devicetree/bindings/clock/ste-u300-syscon-clock.txt new file mode 100644 index 000000000..7cafcb98e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ste-u300-syscon-clock.txt @@ -0,0 +1,80 @@ +Clock bindings for ST-Ericsson U300 System Controller Clocks + +Bindings for the gated system controller clocks: + +Required properties: +- compatible: must be "stericsson,u300-syscon-clk" +- #clock-cells: must be <0> +- clock-type: specifies the type of clock: + 0 = slow clock + 1 = fast clock + 2 = rest/remaining clock +- clock-id: specifies the clock in the type range + +Optional properties: +- clocks: parent clock(s) + +The available clocks per type are as follows: + +Type: ID: Clock: +------------------- +0 0 Slow peripheral bridge clock +0 1 UART0 clock +0 4 GPIO clock +0 6 RTC clock +0 7 Application timer clock +0 8 Access timer clock + +1 0 Fast peripheral bridge clock +1 1 I2C bus 0 clock +1 2 I2C bus 1 clock +1 5 MMC interface peripheral (silicon) clock +1 6 SPI clock + +2 3 CPU clock +2 4 DMA controller clock +2 5 External Memory Interface (EMIF) clock +2 6 NAND flask interface clock +2 8 XGAM graphics engine clock +2 9 Shared External Memory Interface (SEMI) clock +2 10 AHB Subsystem Bridge clock +2 12 Interrupt controller clock + +Example: + +gpio_clk: gpio_clk@13M { + #clock-cells = <0>; + compatible = "stericsson,u300-syscon-clk"; + clock-type = <0>; /* Slow */ + clock-id = <4>; + clocks = <&slow_clk>; +}; + +gpio: gpio@c0016000 { + compatible = "stericsson,gpio-coh901"; + (...) + clocks = <&gpio_clk>; +}; + + +Bindings for the MMC/SD card clock: + +Required properties: +- compatible: must be "stericsson,u300-syscon-mclk" +- #clock-cells: must be <0> + +Optional properties: +- clocks: parent clock(s) + +mmc_mclk: mmc_mclk { + #clock-cells = <0>; + compatible = "stericsson,u300-syscon-mclk"; + clocks = <&mmc_pclk>; +}; + +mmcsd: mmcsd@c0001000 { + compatible = "arm,pl18x", "arm,primecell"; + clocks = <&mmc_pclk>, <&mmc_mclk>; + clock-names = "apb_pclk", "mclk"; + (...) +}; diff --git a/Documentation/devicetree/bindings/clock/stericsson,abx500.txt b/Documentation/devicetree/bindings/clock/stericsson,abx500.txt new file mode 100644 index 000000000..dbaa886b2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/stericsson,abx500.txt @@ -0,0 +1,20 @@ +Clock bindings for ST-Ericsson ABx500 clocks + +Required properties : +- compatible : shall contain the following: + "stericsson,ab8500-clk" +- #clock-cells should be <1> + +The ABx500 clocks need to be placed as a subnode of an AB8500 +device node, see mfd/ab8500.txt + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/ste-ab8500.h header and can be used in device +tree sources. + +Example: + +clock-controller { + compatible = "stericsson,ab8500-clk"; + #clock-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sun8i-de2.txt b/Documentation/devicetree/bindings/clock/sun8i-de2.txt new file mode 100644 index 000000000..e94582e8b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sun8i-de2.txt @@ -0,0 +1,33 @@ +Allwinner Display Engine 2.0 Clock Control Binding +-------------------------------------------------- + +Required properties : +- compatible: must contain one of the following compatibles: + - "allwinner,sun8i-a83t-de2-clk" + - "allwinner,sun8i-h3-de2-clk" + - "allwinner,sun8i-v3s-de2-clk" + - "allwinner,sun50i-a64-de2-clk" + - "allwinner,sun50i-h5-de2-clk" + +- reg: Must contain the registers base address and length +- clocks: phandle to the clocks feeding the display engine subsystem. + Three are needed: + - "mod": the display engine module clock (on A83T it's the DE PLL) + - "bus": the bus clock for the whole display engine subsystem +- clock-names: Must contain the clock names described just above +- resets: phandle to the reset control for the display engine subsystem. +- #clock-cells : must contain 1 +- #reset-cells : must contain 1 + +Example: +de2_clocks: clock@1000000 { + compatible = "allwinner,sun8i-h3-de2-clk"; + reg = <0x01000000 0x100000>; + clocks = <&ccu CLK_BUS_DE>, + <&ccu CLK_DE>; + clock-names = "bus", + "mod"; + resets = <&ccu RST_BUS_DE>; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sun9i-de.txt b/Documentation/devicetree/bindings/clock/sun9i-de.txt new file mode 100644 index 000000000..fb18f327b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sun9i-de.txt @@ -0,0 +1,28 @@ +Allwinner A80 Display Engine Clock Control Binding +-------------------------------------------------- + +Required properties : +- compatible: must contain one of the following compatibles: + - "allwinner,sun9i-a80-de-clks" + +- reg: Must contain the registers base address and length +- clocks: phandle to the clocks feeding the display engine subsystem. + Three are needed: + - "mod": the display engine module clock + - "dram": the DRAM bus clock for the system + - "bus": the bus clock for the whole display engine subsystem +- clock-names: Must contain the clock names described just above +- resets: phandle to the reset control for the display engine subsystem. +- #clock-cells : must contain 1 +- #reset-cells : must contain 1 + +Example: +de_clocks: clock@3000000 { + compatible = "allwinner,sun9i-a80-de-clks"; + reg = <0x03000000 0x30>; + clocks = <&ccu CLK_DE>, <&ccu CLK_SDRAM>, <&ccu CLK_BUS_DE>; + clock-names = "mod", "dram", "bus"; + resets = <&ccu RST_BUS_DE>; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sun9i-usb.txt b/Documentation/devicetree/bindings/clock/sun9i-usb.txt new file mode 100644 index 000000000..3564bd4f2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sun9i-usb.txt @@ -0,0 +1,24 @@ +Allwinner A80 USB Clock Control Binding +--------------------------------------- + +Required properties : +- compatible: must contain one of the following compatibles: + - "allwinner,sun9i-a80-usb-clocks" + +- reg: Must contain the registers base address and length +- clocks: phandle to the clocks feeding the USB subsystem. Two are needed: + - "bus": the bus clock for the whole USB subsystem + - "hosc": the high frequency oscillator (usually at 24MHz) +- clock-names: Must contain the clock names described just above +- #clock-cells : must contain 1 +- #reset-cells : must contain 1 + +Example: +usb_clocks: clock@a08000 { + compatible = "allwinner,sun9i-a80-usb-clks"; + reg = <0x00a08000 0x8>; + clocks = <&ccu CLK_BUS_USB>, <&osc24M>; + clock-names = "bus", "hosc"; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sunxi-ccu.txt b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt new file mode 100644 index 000000000..47d2e902c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi-ccu.txt @@ -0,0 +1,61 @@ +Allwinner Clock Control Unit Binding +------------------------------------ + +Required properties : +- compatible: must contain one of the following compatibles: + - "allwinner,sun4i-a10-ccu" + - "allwinner,sun5i-a10s-ccu" + - "allwinner,sun5i-a13-ccu" + - "allwinner,sun6i-a31-ccu" + - "allwinner,sun7i-a20-ccu" + - "allwinner,sun8i-a23-ccu" + - "allwinner,sun8i-a33-ccu" + - "allwinner,sun8i-a83t-ccu" + - "allwinner,sun8i-a83t-r-ccu" + - "allwinner,sun8i-h3-ccu" + - "allwinner,sun8i-h3-r-ccu" ++ - "allwinner,sun8i-r40-ccu" + - "allwinner,sun8i-v3s-ccu" + - "allwinner,sun9i-a80-ccu" + - "allwinner,sun50i-a64-ccu" + - "allwinner,sun50i-a64-r-ccu" + - "allwinner,sun50i-h5-ccu" + - "allwinner,sun50i-h6-ccu" + - "allwinner,sun50i-h6-r-ccu" + - "nextthing,gr8-ccu" + +- reg: Must contain the registers base address and length +- clocks: phandle to the oscillators feeding the CCU. Two are needed: + - "hosc": the high frequency oscillator (usually at 24MHz) + - "losc": the low frequency oscillator (usually at 32kHz) + On the A83T, this is the internal 16MHz oscillator divided by 512 +- clock-names: Must contain the clock names described just above +- #clock-cells : must contain 1 +- #reset-cells : must contain 1 + +For the main CCU on H6, one more clock is needed: +- "iosc": the SoC's internal frequency oscillator + +For the PRCM CCUs on A83T/H3/A64/H6, two more clocks are needed: +- "pll-periph": the SoC's peripheral PLL from the main CCU +- "iosc": the SoC's internal frequency oscillator + +Example for generic CCU: +ccu: clock@1c20000 { + compatible = "allwinner,sun8i-h3-ccu"; + reg = <0x01c20000 0x400>; + clocks = <&osc24M>, <&osc32k>; + clock-names = "hosc", "losc"; + #clock-cells = <1>; + #reset-cells = <1>; +}; + +Example for PRCM CCU: +r_ccu: clock@1f01400 { + compatible = "allwinner,sun50i-a64-r-ccu"; + reg = <0x01f01400 0x100>; + clocks = <&osc24M>, <&osc32k>, <&iosc>, <&ccu CLK_PLL_PERIPH0>; + clock-names = "hosc", "losc", "iosc", "pll-periph"; + #clock-cells = <1>; + #reset-cells = <1>; +}; diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt new file mode 100644 index 000000000..1a042e20b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/sunxi.txt @@ -0,0 +1,225 @@ +Device Tree Clock bindings for arch-sunxi + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "allwinner,sun4i-a10-osc-clk" - for a gatable oscillator + "allwinner,sun4i-a10-pll1-clk" - for the main PLL clock and PLL4 + "allwinner,sun6i-a31-pll1-clk" - for the main PLL clock on A31 + "allwinner,sun8i-a23-pll1-clk" - for the main PLL clock on A23 + "allwinner,sun4i-a10-pll3-clk" - for the video PLL clock on A10 + "allwinner,sun9i-a80-pll4-clk" - for the peripheral PLLs on A80 + "allwinner,sun4i-a10-pll5-clk" - for the PLL5 clock + "allwinner,sun4i-a10-pll6-clk" - for the PLL6 clock + "allwinner,sun6i-a31-pll6-clk" - for the PLL6 clock on A31 + "allwinner,sun9i-a80-gt-clk" - for the GT bus clock on A80 + "allwinner,sun4i-a10-cpu-clk" - for the CPU multiplexer clock + "allwinner,sun4i-a10-axi-clk" - for the AXI clock + "allwinner,sun8i-a23-axi-clk" - for the AXI clock on A23 + "allwinner,sun4i-a10-gates-clk" - for generic gates on all compatible SoCs + "allwinner,sun4i-a10-axi-gates-clk" - for the AXI gates + "allwinner,sun4i-a10-ahb-clk" - for the AHB clock + "allwinner,sun5i-a13-ahb-clk" - for the AHB clock on A13 + "allwinner,sun9i-a80-ahb-clk" - for the AHB bus clocks on A80 + "allwinner,sun4i-a10-ahb-gates-clk" - for the AHB gates on A10 + "allwinner,sun5i-a13-ahb-gates-clk" - for the AHB gates on A13 + "allwinner,sun5i-a10s-ahb-gates-clk" - for the AHB gates on A10s + "allwinner,sun7i-a20-ahb-gates-clk" - for the AHB gates on A20 + "allwinner,sun6i-a31-ar100-clk" - for the AR100 on A31 + "allwinner,sun9i-a80-cpus-clk" - for the CPUS on A80 + "allwinner,sun6i-a31-ahb1-clk" - for the AHB1 clock on A31 + "allwinner,sun8i-h3-ahb2-clk" - for the AHB2 clock on H3 + "allwinner,sun6i-a31-ahb1-gates-clk" - for the AHB1 gates on A31 + "allwinner,sun8i-a23-ahb1-gates-clk" - for the AHB1 gates on A23 + "allwinner,sun9i-a80-ahb0-gates-clk" - for the AHB0 gates on A80 + "allwinner,sun9i-a80-ahb1-gates-clk" - for the AHB1 gates on A80 + "allwinner,sun9i-a80-ahb2-gates-clk" - for the AHB2 gates on A80 + "allwinner,sun4i-a10-apb0-clk" - for the APB0 clock + "allwinner,sun6i-a31-apb0-clk" - for the APB0 clock on A31 + "allwinner,sun8i-a23-apb0-clk" - for the APB0 clock on A23 + "allwinner,sun9i-a80-apb0-clk" - for the APB0 bus clock on A80 + "allwinner,sun8i-a83t-apb0-gates-clk" - for the APB0 gates on A83T + "allwinner,sun4i-a10-apb0-gates-clk" - for the APB0 gates on A10 + "allwinner,sun5i-a13-apb0-gates-clk" - for the APB0 gates on A13 + "allwinner,sun5i-a10s-apb0-gates-clk" - for the APB0 gates on A10s + "allwinner,sun6i-a31-apb0-gates-clk" - for the APB0 gates on A31 + "allwinner,sun7i-a20-apb0-gates-clk" - for the APB0 gates on A20 + "allwinner,sun8i-a23-apb0-gates-clk" - for the APB0 gates on A23 + "allwinner,sun8i-h3-apb0-gates-clk" - for the APB0 gates on H3 + "allwinner,sun9i-a80-apb0-gates-clk" - for the APB0 gates on A80 + "allwinner,sun4i-a10-apb1-clk" - for the APB1 clock + "allwinner,sun9i-a80-apb1-clk" - for the APB1 bus clock on A80 + "allwinner,sun4i-a10-apb1-gates-clk" - for the APB1 gates on A10 + "allwinner,sun5i-a13-apb1-gates-clk" - for the APB1 gates on A13 + "allwinner,sun5i-a10s-apb1-gates-clk" - for the APB1 gates on A10s + "allwinner,sun6i-a31-apb1-gates-clk" - for the APB1 gates on A31 + "allwinner,sun7i-a20-apb1-gates-clk" - for the APB1 gates on A20 + "allwinner,sun8i-a23-apb1-gates-clk" - for the APB1 gates on A23 + "allwinner,sun9i-a80-apb1-gates-clk" - for the APB1 gates on A80 + "allwinner,sun6i-a31-apb2-gates-clk" - for the APB2 gates on A31 + "allwinner,sun8i-a23-apb2-gates-clk" - for the APB2 gates on A23 + "allwinner,sun8i-a83t-bus-gates-clk" - for the bus gates on A83T + "allwinner,sun8i-h3-bus-gates-clk" - for the bus gates on H3 + "allwinner,sun9i-a80-apbs-gates-clk" - for the APBS gates on A80 + "allwinner,sun4i-a10-display-clk" - for the display clocks on the A10 + "allwinner,sun4i-a10-dram-gates-clk" - for the DRAM gates on A10 + "allwinner,sun5i-a13-dram-gates-clk" - for the DRAM gates on A13 + "allwinner,sun5i-a13-mbus-clk" - for the MBUS clock on A13 + "allwinner,sun4i-a10-mmc-clk" - for the MMC clock + "allwinner,sun9i-a80-mmc-clk" - for mmc module clocks on A80 + "allwinner,sun9i-a80-mmc-config-clk" - for mmc gates + resets on A80 + "allwinner,sun4i-a10-mod0-clk" - for the module 0 family of clocks + "allwinner,sun9i-a80-mod0-clk" - for module 0 (storage) clocks on A80 + "allwinner,sun8i-a23-mbus-clk" - for the MBUS clock on A23 + "allwinner,sun7i-a20-out-clk" - for the external output clocks + "allwinner,sun7i-a20-gmac-clk" - for the GMAC clock module on A20/A31 + "allwinner,sun4i-a10-tcon-ch0-clk" - for the TCON channel 0 clock on the A10 + "allwinner,sun4i-a10-tcon-ch1-clk" - for the TCON channel 1 clock on the A10 + "allwinner,sun4i-a10-usb-clk" - for usb gates + resets on A10 / A20 + "allwinner,sun5i-a13-usb-clk" - for usb gates + resets on A13 + "allwinner,sun6i-a31-usb-clk" - for usb gates + resets on A31 + "allwinner,sun8i-a23-usb-clk" - for usb gates + resets on A23 + "allwinner,sun8i-h3-usb-clk" - for usb gates + resets on H3 + "allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80 + "allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80 + "allwinner,sun4i-a10-ve-clk" - for the Video Engine clock + "allwinner,sun6i-a31-display-clk" - for the display clocks + +Required properties for all clocks: +- reg : shall be the control register address for the clock. +- clocks : shall be the input parent clock(s) phandle for the clock. For + multiplexed clocks, the list order must match the hardware + programming order. +- #clock-cells : from common clock binding; shall be set to 0 except for + the following compatibles where it shall be set to 1: + "allwinner,*-gates-clk", "allwinner,sun4i-pll5-clk", + "allwinner,sun4i-pll6-clk", "allwinner,sun6i-a31-pll6-clk", + "allwinner,*-usb-clk", "allwinner,*-mmc-clk", + "allwinner,*-mmc-config-clk" +- clock-output-names : shall be the corresponding names of the outputs. + If the clock module only has one output, the name shall be the + module name. + +And "allwinner,*-usb-clk" clocks also require: +- reset-cells : shall be set to 1 + +The "allwinner,sun4i-a10-ve-clk" clock also requires: +- reset-cells : shall be set to 0 + +The "allwinner,sun9i-a80-mmc-config-clk" clock also requires: +- #reset-cells : shall be set to 1 +- resets : shall be the reset control phandle for the mmc block. + +For "allwinner,sun7i-a20-gmac-clk", the parent clocks shall be fixed rate +dummy clocks at 25 MHz and 125 MHz, respectively. See example. + +Clock consumers should specify the desired clocks they use with a +"clocks" phandle cell. Consumers that are using a gated clock should +provide an additional ID in their clock property. This ID is the +offset of the bit controlling this particular gate in the register. +For the other clocks with "#clock-cells" = 1, the additional ID shall +refer to the index of the output. + +For "allwinner,sun6i-a31-pll6-clk", there are 2 outputs. The first output +is the normal PLL6 output, or "pll6". The second output is rate doubled +PLL6, or "pll6x2". + +The "allwinner,*-mmc-clk" clocks have three different outputs: the +main clock, with the ID 0, and the output and sample clocks, with the +IDs 1 and 2, respectively. + +The "allwinner,sun9i-a80-mmc-config-clk" clock has one clock/reset output +per mmc controller. The number of outputs is determined by the size of +the address block, which is related to the overall mmc block. + +For example: + +osc24M: clk@1c20050 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-osc-clk"; + reg = <0x01c20050 0x4>; + clocks = <&osc24M_fixed>; + clock-output-names = "osc24M"; +}; + +pll1: clk@1c20000 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-pll1-clk"; + reg = <0x01c20000 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll1"; +}; + +pll5: clk@1c20020 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-pll5-clk"; + reg = <0x01c20020 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll5_ddr", "pll5_other"; +}; + +pll6: clk@1c20028 { + #clock-cells = <1>; + compatible = "allwinner,sun6i-a31-pll6-clk"; + reg = <0x01c20028 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll6", "pll6x2"; +}; + +cpu: cpu@1c20054 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-cpu-clk"; + reg = <0x01c20054 0x4>; + clocks = <&osc32k>, <&osc24M>, <&pll1>; + clock-output-names = "cpu"; +}; + +mmc0_clk: clk@1c20088 { + #clock-cells = <1>; + compatible = "allwinner,sun4i-a10-mmc-clk"; + reg = <0x01c20088 0x4>; + clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; + clock-output-names = "mmc0", "mmc0_output", "mmc0_sample"; +}; + +mii_phy_tx_clk: clk@2 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "mii_phy_tx"; +}; + +gmac_int_tx_clk: clk@3 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "gmac_int_tx"; +}; + +gmac_clk: clk@1c20164 { + #clock-cells = <0>; + compatible = "allwinner,sun7i-a20-gmac-clk"; + reg = <0x01c20164 0x4>; + /* + * The first clock must be fixed at 25MHz; + * the second clock must be fixed at 125MHz + */ + clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>; + clock-output-names = "gmac"; +}; + +mmc_config_clk: clk@1c13000 { + compatible = "allwinner,sun9i-a80-mmc-config-clk"; + reg = <0x01c13000 0x10>; + clocks = <&ahb0_gates 8>; + clock-names = "ahb"; + resets = <&ahb0_resets 8>; + reset-names = "ahb"; + #clock-cells = <1>; + #reset-cells = <1>; + clock-output-names = "mmc0_config", "mmc1_config", + "mmc2_config", "mmc3_config"; +}; diff --git a/Documentation/devicetree/bindings/clock/tango4-clock.txt b/Documentation/devicetree/bindings/clock/tango4-clock.txt new file mode 100644 index 000000000..19c580a7b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/tango4-clock.txt @@ -0,0 +1,23 @@ +* Sigma Designs Tango4 Clock Generator + +The Tango4 clock generator outputs cpu_clk and sys_clk (the latter is used +for RAM and various peripheral devices). The clock binding described here +is applicable to all Tango4 SoCs. + +Required Properties: + +- compatible: should be "sigma,tango4-clkgen". +- reg: physical base address of the device and length of memory mapped region. +- clocks: phandle of the input clock (crystal oscillator). +- clock-output-names: should be "cpuclk" and "sysclk". +- #clock-cells: should be set to 1. + +Example: + + clkgen: clkgen@10000 { + compatible = "sigma,tango4-clkgen"; + reg = <0x10000 0x40>; + clocks = <&xtal>; + clock-output-names = "cpuclk", "sysclk"; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti,cdce706.txt b/Documentation/devicetree/bindings/clock/ti,cdce706.txt new file mode 100644 index 000000000..959d96632 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti,cdce706.txt @@ -0,0 +1,42 @@ +Bindings for Texas Instruments CDCE706 programmable 3-PLL clock +synthesizer/multiplier/divider. + +Reference: http://www.ti.com/lit/ds/symlink/cdce706.pdf + +I2C device node required properties: +- compatible: shall be "ti,cdce706". +- reg: i2c device address, shall be in range [0x68...0x6b]. +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: from common clock binding; list of parent clock + handles, shall be reference clock(s) connected to CLK_IN0 + and CLK_IN1 pins. +- clock-names: shall be clk_in0 and/or clk_in1. Use clk_in0 + in case of crystal oscillator or differential signal input + configuration. Use clk_in0 and clk_in1 in case of independent + single-ended LVCMOS inputs configuration. + +Example: + + clocks { + clk54: clk54 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <54000000>; + }; + }; + ... + i2c0: i2c-master@d090000 { + ... + cdce706: clock-synth@69 { + compatible = "ti,cdce706"; + #clock-cells = <1>; + reg = <0x69>; + clocks = <&clk54>; + clock-names = "clk_in0"; + }; + }; + ... + simple-audio-card,codec { + ... + clocks = <&cdce706 4>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti,cdce925.txt b/Documentation/devicetree/bindings/clock/ti,cdce925.txt new file mode 100644 index 000000000..0d01f2d5c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti,cdce925.txt @@ -0,0 +1,49 @@ +Binding for TI CDCE913/925/937/949 programmable I2C clock synthesizers. + +Reference +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] http://www.ti.com/product/cdce913 +[3] http://www.ti.com/product/cdce925 +[4] http://www.ti.com/product/cdce937 +[5] http://www.ti.com/product/cdce949 + +The driver provides clock sources for each output Y1 through Y5. + +Required properties: + - compatible: Shall be one of the following: + - "ti,cdce913": 1-PLL, 3 Outputs + - "ti,cdce925": 2-PLL, 5 Outputs + - "ti,cdce937": 3-PLL, 7 Outputs + - "ti,cdce949": 4-PLL, 9 Outputs + - reg: I2C device address. + - clocks: Points to a fixed parent clock that provides the input frequency. + - #clock-cells: From common clock bindings: Shall be 1. + +Optional properties: + - xtal-load-pf: Crystal load-capacitor value to fine-tune performance on a + board, or to compensate for external influences. + +For all PLL1, PLL2, ... an optional child node can be used to specify spread +spectrum clocking parameters for a board. + - spread-spectrum: SSC mode as defined in the data sheet. + - spread-spectrum-center: Use "centered" mode instead of "max" mode. When + present, the clock runs at the requested frequency on average. Otherwise + the requested frequency is the maximum value of the SCC range. + + +Example: + + clockgen: cdce925pw@64 { + compatible = "cdce925"; + reg = <0x64>; + clocks = <&xtal_27Mhz>; + #clock-cells = <1>; + xtal-load-pf = <5>; + /* PLL options to get SSC 1% centered */ + PLL2 { + spread-spectrum = <4>; + spread-spectrum-center; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/ti,sci-clk.txt b/Documentation/devicetree/bindings/clock/ti,sci-clk.txt new file mode 100644 index 000000000..4e59dc6b1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti,sci-clk.txt @@ -0,0 +1,36 @@ +Texas Instruments TI-SCI Clocks +=============================== + +All clocks on Texas Instruments' SoCs that contain a System Controller, +are only controlled by this entity. Communication between a host processor +running an OS and the System Controller happens through a protocol known +as TI-SCI[1]. This clock implementation plugs into the common clock +framework and makes use of the TI-SCI protocol on clock API requests. + +[1] Documentation/devicetree/bindings/arm/keystone/ti,sci.txt + +Required properties: +------------------- +- compatible: Must be "ti,k2g-sci-clk" +- #clock-cells: Shall be 2. + In clock consumers, this cell represents the device ID and clock ID + exposed by the PM firmware. The list of valid values for the device IDs + and clocks IDs for 66AK2G SoC are documented at + http://processors.wiki.ti.com/index.php/TISCI#66AK2G02_Data + +Examples: +-------- + +pmmc: pmmc { + compatible = "ti,k2g-sci"; + + k2g_clks: clocks { + compatible = "ti,k2g-sci-clk"; + #clock-cells = <2>; + }; +}; + +uart0: serial@2530c00 { + compatible = "ns16550a"; + clocks = <&k2g_clks 0x2c 0>; +}; diff --git a/Documentation/devicetree/bindings/clock/ti-clkctrl.txt b/Documentation/devicetree/bindings/clock/ti-clkctrl.txt new file mode 100644 index 000000000..48ee6991f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti-clkctrl.txt @@ -0,0 +1,56 @@ +Texas Instruments clkctrl clock binding + +Texas Instruments SoCs can have a clkctrl clock controller for each +interconnect target module. The clkctrl clock controller manages functional +and interface clocks for each module. Each clkctrl controller can also +gate one or more optional functional clocks for a module, and can have one +or more clock muxes. There is a clkctrl clock controller typically for each +interconnect target module on omap4 and later variants. + +The clock consumers can specify the index of the clkctrl clock using +the hardware offset from the clkctrl instance register space. The optional +clocks can be specified by clkctrl hardware offset and the index of the +optional clock. + +For more information, please see the Linux clock framework binding at +Documentation/devicetree/bindings/clock/clock-bindings.txt. + +Required properties : +- compatible : shall be "ti,clkctrl" +- #clock-cells : shall contain 2 with the first entry being the instance + offset from the clock domain base and the second being the + clock index + +Example: Clock controller node on omap 4430: + +&cm2 { + l4per: cm@1400 { + cm_l4per@0 { + cm_l4per_clkctrl: clk@20 { + compatible = "ti,clkctrl"; + reg = <0x20 0x1b0>; + #clock-cells = <2>; + }; + }; + }; +}; + +Example: Preprocessor helper macros in dt-bindings/clock/ti-clkctrl.h + +#define OMAP4_CLKCTRL_OFFSET 0x20 +#define OMAP4_CLKCTRL_INDEX(offset) ((offset) - OMAP4_CLKCTRL_OFFSET) +#define MODULEMODE_HWCTRL 1 +#define MODULEMODE_SWCTRL 2 + +#define OMAP4_GPTIMER10_CLKTRL OMAP4_CLKCTRL_INDEX(0x28) +#define OMAP4_GPTIMER11_CLKTRL OMAP4_CLKCTRL_INDEX(0x30) +#define OMAP4_GPTIMER2_CLKTRL OMAP4_CLKCTRL_INDEX(0x38) +... +#define OMAP4_GPIO2_CLKCTRL OMAP_CLKCTRL_INDEX(0x60) + +Example: Clock consumer node for GPIO2: + +&gpio2 { + clocks = <&cm_l4per_clkctrl OMAP4_GPIO2_CLKCTRL 0 + &cm_l4per_clkctrl OMAP4_GPIO2_CLKCTRL 8>; +}; diff --git a/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt new file mode 100644 index 000000000..c35cb6c4a --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti-keystone-pllctrl.txt @@ -0,0 +1,20 @@ +* Device tree bindings for Texas Instruments keystone pll controller + +The main pll controller used to drive theC66x CorePacs, the switch fabric, +and a majority of the peripheral clocks (all but the ARM CorePacs, DDR3 and +the NETCP modules) requires a PLL Controller to manage the various clock +divisions, gating, and synchronization. + +Required properties: + +- compatible: "ti,keystone-pllctrl", "syscon" + +- reg: contains offset/length value for pll controller + registers space. + +Example: + +pllctrl: pll-controller@02310000 { + compatible = "ti,keystone-pllctrl", "syscon"; + reg = <0x02310000 0x200>; +}; diff --git a/Documentation/devicetree/bindings/clock/ti/adpll.txt b/Documentation/devicetree/bindings/clock/ti/adpll.txt new file mode 100644 index 000000000..4c8a2ce2c --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/adpll.txt @@ -0,0 +1,41 @@ +Binding for Texas Instruments ADPLL clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped ADPLL with two to three selectable input clocks +and three to four children. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of "ti,dm814-adpll-s-clock" or + "ti,dm814-adpll-lj-clock" depending on the type of the ADPLL +- #clock-cells : from common clock binding; shall be set to 1. +- clocks : link phandles of parent clocks clkinp and clkinpulow, note + that the adpll-s-clock also has an optional clkinphif +- reg : address and length of the register set for controlling the ADPLL. + +Examples: + adpll_mpu_ck: adpll@40 { + #clock-cells = <1>; + compatible = "ti,dm814-adpll-s-clock"; + reg = <0x40 0x40>; + clocks = <&devosc_ck &devosc_ck &devosc_ck>; + clock-names = "clkinp", "clkinpulow", "clkinphif"; + clock-output-names = "481c5040.adpll.dcoclkldo", + "481c5040.adpll.clkout", + "481c5040.adpll.clkoutx2", + "481c5040.adpll.clkouthif"; + }; + + adpll_dsp_ck: adpll@80 { + #clock-cells = <1>; + compatible = "ti,dm814-adpll-lj-clock"; + reg = <0x80 0x30>; + clocks = <&devosc_ck &devosc_ck>; + clock-names = "clkinp", "clkinpulow"; + clock-output-names = "481c5080.adpll.dcoclkldo", + "481c5080.adpll.clkout", + "481c5080.adpll.clkoutldo"; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/apll.txt b/Documentation/devicetree/bindings/clock/ti/apll.txt new file mode 100644 index 000000000..ade4dd4c3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/apll.txt @@ -0,0 +1,45 @@ +Binding for Texas Instruments APLL clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped APLL with usually two selectable input clocks +(reference clock and bypass clock), with analog phase locked +loop logic for multiplying the input clock to a desired output +clock. This clock also typically supports different operation +modes (locked, low power stop etc.) APLL mostly behaves like +a subtype of a DPLL [2], although a simplified one at that. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/ti/dpll.txt + +Required properties: +- compatible : shall be "ti,dra7-apll-clock" or "ti,omap2-apll-clock" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of parent clocks (clk-ref and clk-bypass) +- reg : address and length of the register set for controlling the APLL. + It contains the information of registers in the following order: + "control" - contains the control register offset + "idlest" - contains the idlest register offset + "autoidle" - contains the autoidle register offset (OMAP2 only) +- ti,clock-frequency : static clock frequency for the clock (OMAP2 only) +- ti,idlest-shift : bit-shift for the idlest field (OMAP2 only) +- ti,bit-shift : bit-shift for enable and autoidle fields (OMAP2 only) + +Examples: + apll_pcie_ck: apll_pcie_ck { + #clock-cells = <0>; + clocks = <&apll_pcie_in_clk_mux>, <&dpll_pcie_ref_ck>; + reg = <0x021c>, <0x0220>; + compatible = "ti,dra7-apll-clock"; + }; + + apll96_ck: apll96_ck { + #clock-cells = <0>; + compatible = "ti,omap2-apll-clock"; + clocks = <&sys_ck>; + ti,bit-shift = <2>; + ti,idlest-shift = <8>; + ti,clock-frequency = <96000000>; + reg = <0x0500>, <0x0530>, <0x0520>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/autoidle.txt b/Documentation/devicetree/bindings/clock/ti/autoidle.txt new file mode 100644 index 000000000..7c735dde9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/autoidle.txt @@ -0,0 +1,39 @@ +Binding for Texas Instruments autoidle clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a register mapped +clock which can be put to idle automatically by hardware based on the usage +and a configuration bit setting. Autoidle clock is never an individual +clock, it is always a derivative of some basic clock like a gate, divider, +or fixed-factor. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- reg : offset for the register controlling the autoidle +- ti,autoidle-shift : bit shift of the autoidle enable bit +- ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0 + +Examples: + dpll_core_m4_ck: dpll_core_m4_ck { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_core_x2_ck>; + ti,max-div = <31>; + ti,autoidle-shift = <8>; + reg = <0x2d38>; + ti,index-starts-at-one; + ti,invert-autoidle-bit; + }; + + dpll_usb_clkdcoldo_ck: dpll_usb_clkdcoldo_ck { + #clock-cells = <0>; + compatible = "ti,fixed-factor-clock"; + clocks = <&dpll_usb_ck>; + ti,clock-div = <1>; + ti,autoidle-shift = <8>; + reg = <0x01b4>; + ti,clock-mult = <1>; + ti,invert-autoidle-bit; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/clockdomain.txt b/Documentation/devicetree/bindings/clock/ti/clockdomain.txt new file mode 100644 index 000000000..cb76b3f2b --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/clockdomain.txt @@ -0,0 +1,24 @@ +Binding for Texas Instruments clockdomain. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1] in consumer role. +Every clock on TI SoC belongs to one clockdomain, but software +only needs this information for specific clocks which require +their parent clockdomain to be controlled when the clock is +enabled/disabled. This binding doesn't define a new clock +binding type, it is used to group existing clock nodes under +hardware hierarchy. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,clockdomain" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of clocks within this domain + +Examples: + dss_clkdm: dss_clkdm { + compatible = "ti,clockdomain"; + clocks = <&dss1_alwon_fck_3430es2>, <&dss_ick_3430es2>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/composite.txt b/Documentation/devicetree/bindings/clock/ti/composite.txt new file mode 100644 index 000000000..5f43c4706 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/composite.txt @@ -0,0 +1,54 @@ +Binding for TI composite clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped composite clock with multiple different sub-types; + +a multiplexer clock with multiple input clock signals or parents, one +of which can be selected as output, this behaves exactly as [2] + +an adjustable clock rate divider, this behaves exactly as [3] + +a gating function which can be used to enable and disable the output +clock, this behaves exactly as [4] + +The binding must provide a list of the component clocks that shall be +merged to this clock. The component clocks shall be of one of the +"ti,*composite*-clock" types. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/ti/mux.txt +[3] Documentation/devicetree/bindings/clock/ti/divider.txt +[4] Documentation/devicetree/bindings/clock/ti/gate.txt + +Required properties: +- compatible : shall be: "ti,composite-clock" +- clocks : link phandles of component clocks +- #clock-cells : from common clock binding; shall be set to 0. + +Examples: + +usb_l4_gate_ick: usb_l4_gate_ick { + #clock-cells = <0>; + compatible = "ti,composite-interface-clock"; + clocks = <&l4_ick>; + ti,bit-shift = <5>; + reg = <0x0a10>; +}; + +usb_l4_div_ick: usb_l4_div_ick { + #clock-cells = <0>; + compatible = "ti,composite-divider-clock"; + clocks = <&l4_ick>; + ti,bit-shift = <4>; + ti,max-div = <1>; + reg = <0x0a40>; + ti,index-starts-at-one; +}; + +usb_l4_ick: usb_l4_ick { + #clock-cells = <0>; + compatible = "ti,composite-clock"; + clocks = <&usb_l4_gate_ick>, <&usb_l4_div_ick>; +}; diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt new file mode 100644 index 000000000..1e03dce99 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/da8xx-cfgchip.txt @@ -0,0 +1,93 @@ +Binding for TI DA8XX/OMAP-L13X/AM17XX/AM18XX CFGCHIP clocks + +TI DA8XX/OMAP-L13X/AM17XX/AM18XX SoCs contain a general purpose set of +registers call CFGCHIPn. Some of these registers function as clock +gates. This document describes the bindings for those clocks. + +All of the clock nodes described below must be child nodes of a CFGCHIP node +(compatible = "ti,da830-cfgchip"). + +USB PHY clocks +-------------- +Required properties: +- compatible: shall be "ti,da830-usb-phy-clocks". +- #clock-cells: from common clock binding; shall be set to 1. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "fck", "usb_refclkin", "auxclk" + +This node provides two clocks. The clock at index 0 is the USB 2.0 PHY 48MHz +clock and the clock at index 1 is the USB 1.1 PHY 48MHz clock. + +eHRPWM Time Base Clock (TBCLK) +------------------------------ +Required properties: +- compatible: shall be "ti,da830-tbclksync". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandle to the parent clock +- clock-names: shall be "fck" + +PLL DIV4.5 divider +------------------ +Required properties: +- compatible: shall be "ti,da830-div4p5ena". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandle to the parent clock +- clock-names: shall be "pll0_pllout" + +EMIFA clock source (ASYNC1) +--------------------------- +Required properties: +- compatible: shall be "ti,da850-async1-clksrc". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "pll0_sysclk3", "div4.5" + +ASYNC3 clock source +------------------- +Required properties: +- compatible: shall be "ti,da850-async3-clksrc". +- #clock-cells: from common clock binding; shall be set to 0. +- clocks: phandles to the parent clocks corresponding to clock-names +- clock-names: shall be "pll0_sysclk2", "pll1_sysclk2" + +Examples: + + cfgchip: syscon@1417c { + compatible = "ti,da830-cfgchip", "syscon", "simple-mfd"; + reg = <0x1417c 0x14>; + + usb_phy_clk: usb-phy-clocks { + compatible = "ti,da830-usb-phy-clocks"; + #clock-cells = <1>; + clocks = <&psc1 1>, <&usb_refclkin>, <&pll0_auxclk>; + clock-names = "fck", "usb_refclkin", "auxclk"; + }; + ehrpwm_tbclk: ehrpwm_tbclk { + compatible = "ti,da830-tbclksync"; + #clock-cells = <0>; + clocks = <&psc1 17>; + clock-names = "fck"; + }; + div4p5_clk: div4.5 { + compatible = "ti,da830-div4p5ena"; + #clock-cells = <0>; + clocks = <&pll0_pllout>; + clock-names = "pll0_pllout"; + }; + async1_clk: async1 { + compatible = "ti,da850-async1-clksrc"; + #clock-cells = <0>; + clocks = <&pll0_sysclk 3>, <&div4p5_clk>; + clock-names = "pll0_sysclk3", "div4.5"; + }; + async3_clk: async3 { + compatible = "ti,da850-async3-clksrc"; + #clock-cells = <0>; + clocks = <&pll0_sysclk 2>, <&pll1_sysclk 2>; + clock-names = "pll0_sysclk2", "pll1_sysclk2"; + }; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt + diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt new file mode 100644 index 000000000..36998e184 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/pll.txt @@ -0,0 +1,96 @@ +Binding for TI DaVinci PLL Controllers + +The PLL provides clocks to most of the components on the SoC. In addition +to the PLL itself, this controller also contains bypasses, gates, dividers, +an multiplexers for various clock signals. + +Required properties: +- compatible: shall be one of: + - "ti,da850-pll0" for PLL0 on DA850/OMAP-L138/AM18XX + - "ti,da850-pll1" for PLL1 on DA850/OMAP-L138/AM18XX +- reg: physical base address and size of the controller's register area. +- clocks: phandles corresponding to the clock names +- clock-names: names of the clock sources - depends on compatible string + - for "ti,da850-pll0", shall be "clksrc", "extclksrc" + - for "ti,da850-pll1", shall be "clksrc" + +Optional properties: +- ti,clkmode-square-wave: Indicates that the the board is supplying a square + wave input on the OSCIN pin instead of using a crystal oscillator. + This property is only valid when compatible = "ti,da850-pll0". + + +Optional child nodes: + +pllout + Describes the main PLL clock output (before POSTDIV). The node name must + be "pllout". + + Required properties: + - #clock-cells: shall be 0 + +sysclk + Describes the PLLDIVn divider clocks that provide the SYSCLKn clock + domains. The node name must be "sysclk". Consumers of this node should + use "n" in "SYSCLKn" as the index parameter for the clock cell. + + Required properties: + - #clock-cells: shall be 1 + +auxclk + Describes the AUXCLK output of the PLL. The node name must be "auxclk". + This child node is only valid when compatible = "ti,da850-pll0". + + Required properties: + - #clock-cells: shall be 0 + +obsclk + Describes the OBSCLK output of the PLL. The node name must be "obsclk". + + Required properties: + - #clock-cells: shall be 0 + + +Examples: + + pll0: clock-controller@11000 { + compatible = "ti,da850-pll0"; + reg = <0x11000 0x1000>; + clocks = <&ref_clk>, <&pll1_sysclk 3>; + clock-names = "clksrc", "extclksrc"; + ti,clkmode-square-wave; + + pll0_pllout: pllout { + #clock-cells = <0>; + }; + + pll0_sysclk: sysclk { + #clock-cells = <1>; + }; + + pll0_auxclk: auxclk { + #clock-cells = <0>; + }; + + pll0_obsclk: obsclk { + #clock-cells = <0>; + }; + }; + + pll1: clock-controller@21a000 { + compatible = "ti,da850-pll1"; + reg = <0x21a000 0x1000>; + clocks = <&ref_clk>; + clock-names = "clksrc"; + + pll0_sysclk: sysclk { + #clock-cells = <1>; + }; + + pll0_obsclk: obsclk { + #clock-cells = <0>; + }; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt diff --git a/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt new file mode 100644 index 000000000..dae4ad8e1 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/davinci/psc.txt @@ -0,0 +1,71 @@ +Binding for TI DaVinci Power Sleep Controller (PSC) + +The PSC provides power management, clock gating and reset functionality. It is +primarily used for clocking. + +Required properties: +- compatible: shall be one of: + - "ti,da850-psc0" for PSC0 on DA850/OMAP-L138/AM18XX + - "ti,da850-psc1" for PSC1 on DA850/OMAP-L138/AM18XX +- reg: physical base address and size of the controller's register area +- #clock-cells: from common clock binding; shall be set to 1 +- #power-domain-cells: from generic power domain binding; shall be set to 1. +- clocks: phandles to clocks corresponding to the clock-names property +- clock-names: list of parent clock names - depends on compatible value + - for "ti,da850-psc0", shall be "pll0_sysclk1", "pll0_sysclk2", + "pll0_sysclk4", "pll0_sysclk6", "async1" + - for "ti,da850-psc1", shall be "pll0_sysclk2", "pll0_sysclk4", "async3" + +Optional properties: +- #reset-cells: from reset binding; shall be set to 1 - only applicable when + at least one local domain provides a local reset. + +Consumers: + + Clock, power domain and reset consumers shall use the local power domain + module ID (LPSC) as the index corresponding to the clock cell. Refer to + the device-specific datasheet to find these numbers. NB: Most local + domains only provide a clock/power domain and not a reset. + +Examples: + + psc0: clock-controller@10000 { + compatible = "ti,da850-psc0"; + reg = <0x10000 0x1000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + #reset-cells = <1>; + clocks = <&pll0_sysclk 1>, <&pll0_sysclk 2>, + <&pll0_sysclk 4>, <&pll0_sysclk 6>, <&async1_clk>; + clock_names = "pll0_sysclk1", "pll0_sysclk2", + "pll0_sysclk4", "pll0_sysclk6", "async1"; + }; + psc1: clock-controller@227000 { + compatible = "ti,da850-psc1"; + reg = <0x227000 0x1000>; + #clock-cells = <1>; + #power-domain-cells = <1>; + clocks = <&pll0_sysclk 2>, <&pll0_sysclk 4>, <&async3_clk>; + clock_names = "pll0_sysclk2", "pll0_sysclk4", "async3"; + }; + + /* consumer */ + dsp: dsp@11800000 { + compatible = "ti,da850-dsp"; + reg = <0x11800000 0x40000>, + <0x11e00000 0x8000>, + <0x11f00000 0x8000>, + <0x01c14044 0x4>, + <0x01c14174 0x8>; + reg-names = "l2sram", "l1pram", "l1dram", "host1cfg", "chipsig"; + interrupt-parent = <&intc>; + interrupts = <28>; + clocks = <&psc0 15>; + power-domains = <&psc0 15>; + resets = <&psc0 15>; + }; + +Also see: +- Documentation/devicetree/bindings/clock/clock-bindings.txt +- Documentation/devicetree/bindings/power/power_domain.txt +- Documentation/devicetree/bindings/reset/reset.txt diff --git a/Documentation/devicetree/bindings/clock/ti/divider.txt b/Documentation/devicetree/bindings/clock/ti/divider.txt new file mode 100644 index 000000000..9b13b3297 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/divider.txt @@ -0,0 +1,117 @@ +Binding for TI divider clock + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped adjustable clock rate divider that does not gate and has +only one input clock or parent. By default the value programmed into +the register is one less than the actual divisor value. E.g: + +register value actual divisor value +0 1 +1 2 +2 3 + +This assumption may be modified by the following optional properties: + +ti,index-starts-at-one - valid divisor values start at 1, not the default +of 0. E.g: +register value actual divisor value +1 1 +2 2 +3 3 + +ti,index-power-of-two - valid divisor values are powers of two. E.g: +register value actual divisor value +0 1 +1 2 +2 4 + +Additionally an array of valid dividers may be supplied like so: + + ti,dividers = <4>, <8>, <0>, <16>; + +Which will map the resulting values to a divisor table by their index: +register value actual divisor value +0 4 +1 8 +2 <invalid divisor, skipped> +3 16 + +Any zero value in this array means the corresponding bit-value is invalid +and must not be used. + +The binding must also provide the register to control the divider and +unless the divider array is provided, min and max dividers. Optionally +the number of bits to shift that mask, if necessary. If the shift value +is missing it is the same as supplying a zero shift. + +This binding can also optionally provide support to the hardware autoidle +feature, see [2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/ti/autoidle.txt + +Required properties: +- compatible : shall be "ti,divider-clock" or "ti,composite-divider-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link to phandle of parent clock +- reg : offset for register controlling adjustable divider + +Optional properties: +- clock-output-names : from common clock binding. +- ti,dividers : array of integers defining divisors +- ti,bit-shift : number of bits to shift the divider value, defaults to 0 +- ti,min-div : min divisor for dividing the input clock rate, only + needed if the first divisor is offset from the default value (1) +- ti,max-div : max divisor for dividing the input clock rate, only needed + if ti,dividers is not defined. +- ti,index-starts-at-one : valid divisor programming starts at 1, not zero, + only valid if ti,dividers is not defined. +- ti,index-power-of-two : valid divisor programming must be a power of two, + only valid if ti,dividers is not defined. +- ti,autoidle-shift : bit shift of the autoidle enable bit for the clock, + see [2] +- ti,invert-autoidle-bit : autoidle is enabled by setting the bit to 0, + see [2] +- ti,set-rate-parent : clk_set_rate is propagated to parent +- ti,latch-bit : latch the divider value to HW, only needed if the register + access requires this. As an example dra76x DPLL_GMAC H14 divider implements + such behavior. + +Examples: +dpll_usb_m2_ck: dpll_usb_m2_ck@4a008190 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&dpll_usb_ck>; + ti,max-div = <127>; + reg = <0x190>; + ti,index-starts-at-one; +}; + +aess_fclk: aess_fclk@4a004528 { + #clock-cells = <0>; + compatible = "ti,divider-clock"; + clocks = <&abe_clk>; + ti,bit-shift = <24>; + reg = <0x528>; + ti,max-div = <2>; +}; + +dpll_core_m3x2_div_ck: dpll_core_m3x2_div_ck { + #clock-cells = <0>; + compatible = "ti,composite-divider-clock"; + clocks = <&dpll_core_x2_ck>; + ti,max-div = <31>; + reg = <0x0134>; + ti,index-starts-at-one; +}; + +ssi_ssr_div_fck_3430es2: ssi_ssr_div_fck_3430es2 { + #clock-cells = <0>; + compatible = "ti,composite-divider-clock"; + clocks = <&corex2_fck>; + ti,bit-shift = <8>; + reg = <0x0a40>; + ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>; +}; diff --git a/Documentation/devicetree/bindings/clock/ti/dpll.txt b/Documentation/devicetree/bindings/clock/ti/dpll.txt new file mode 100644 index 000000000..df57009ff --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/dpll.txt @@ -0,0 +1,85 @@ +Binding for Texas Instruments DPLL clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped DPLL with usually two selectable input clocks +(reference clock and bypass clock), with digital phase locked +loop logic for multiplying the input clock to a desired output +clock. This clock also typically supports different operation +modes (locked, low power stop etc.) This binding has several +sub-types, which effectively result in slightly different setup +for the actual DPLL clock. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of: + "ti,omap3-dpll-clock", + "ti,omap3-dpll-core-clock", + "ti,omap3-dpll-per-clock", + "ti,omap3-dpll-per-j-type-clock", + "ti,omap4-dpll-clock", + "ti,omap4-dpll-x2-clock", + "ti,omap4-dpll-core-clock", + "ti,omap4-dpll-m4xen-clock", + "ti,omap4-dpll-j-type-clock", + "ti,omap5-mpu-dpll-clock", + "ti,am3-dpll-no-gate-clock", + "ti,am3-dpll-j-type-clock", + "ti,am3-dpll-no-gate-j-type-clock", + "ti,am3-dpll-clock", + "ti,am3-dpll-core-clock", + "ti,am3-dpll-x2-clock", + "ti,omap2-dpll-core-clock", + +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of parent clocks, first entry lists reference clock + and second entry bypass clock +- reg : offsets for the register set for controlling the DPLL. + Registers are listed in following order: + "control" - contains the control register base address + "idlest" - contains the idle status register base address + "mult-div1" - contains the multiplier / divider register base address + "autoidle" - contains the autoidle register base address (optional) + ti,am3-* dpll types do not have autoidle register + ti,omap2-* dpll type does not support idlest / autoidle registers + +Optional properties: +- DPLL mode setting - defining any one or more of the following overrides + default setting. + - ti,low-power-stop : DPLL supports low power stop mode, gating output + - ti,low-power-bypass : DPLL output matches rate of parent bypass clock + - ti,lock : DPLL locks in programmed rate + +Examples: + dpll_core_ck: dpll_core_ck@44e00490 { + #clock-cells = <0>; + compatible = "ti,omap4-dpll-core-clock"; + clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; + reg = <0x490>, <0x45c>, <0x488>, <0x468>; + }; + + dpll2_ck: dpll2_ck@48004004 { + #clock-cells = <0>; + compatible = "ti,omap3-dpll-clock"; + clocks = <&sys_ck>, <&dpll2_fck>; + ti,low-power-stop; + ti,low-power-bypass; + ti,lock; + reg = <0x4>, <0x24>, <0x34>, <0x40>; + }; + + dpll_core_ck: dpll_core_ck@44e00490 { + #clock-cells = <0>; + compatible = "ti,am3-dpll-core-clock"; + clocks = <&sys_clkin_ck>, <&sys_clkin_ck>; + reg = <0x90>, <0x5c>, <0x68>; + }; + + dpll_ck: dpll_ck { + #clock-cells = <0>; + compatible = "ti,omap2-dpll-core-clock"; + clocks = <&sys_ck>, <&sys_ck>; + reg = <0x0500>, <0x0540>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt b/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt new file mode 100644 index 000000000..10f704775 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/dra7-atl.txt @@ -0,0 +1,94 @@ +Device Tree Clock bindings for ATL (Audio Tracking Logic) of DRA7 SoC. + +The ATL IP is used to generate clock to be used to synchronize baseband and +audio codec. A single ATL IP provides four ATL clock instances sharing the same +functional clock but can be configured to provide different clocks. +ATL can maintain a clock averages to some desired frequency based on the bws/aws +signals - can compensate the drift between the two ws signal. + +In order to provide the support for ATL and it's output clocks (which can be used +internally within the SoC or external components) two sets of bindings is needed: + +Clock tree binding: +This binding uses the common clock binding[1]. +To be able to integrate the ATL clocks with DT clock tree. +Provides ccf level representation of the ATL clocks to be used by drivers. +Since the clock instances are part of a single IP this binding is used as a node +for the DT clock tree, the IP driver is needed to handle the actual configuration +of the IP. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,dra7-atl-clock" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles to functional clock of ATL + +Binding for the IP driver: +This binding is used to configure the IP driver which is going to handle the +configuration of the IP for the ATL clock instances. + +Required properties: +- compatible : shall be "ti,dra7-atl" +- reg : base address for the ATL IP +- ti,provided-clocks : List of phandles to the clocks associated with the ATL +- clocks : link phandles to functional clock of ATL +- clock-names : Shall be set to "fck" +- ti,hwmods : Shall be set to "atl" + +Optional properties: +Configuration of ATL instances: +- atl{0/1/2/3} { + - bws : Baseband word select signal selection + - aws : Audio word select signal selection +}; + +For valid word select signals, see the dt-bindings/clk/ti-dra7-atl.h include +file. + +Examples: +/* clock bindings for atl provided clocks */ +atl_clkin0_ck: atl_clkin0_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin1_ck: atl_clkin1_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin2_ck: atl_clkin2_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +atl_clkin3_ck: atl_clkin3_ck { + #clock-cells = <0>; + compatible = "ti,dra7-atl-clock"; + clocks = <&atl_gfclk_mux>; +}; + +/* binding for the IP */ +atl: atl@4843c000 { + compatible = "ti,dra7-atl"; + reg = <0x4843c000 0x3ff>; + ti,hwmods = "atl"; + ti,provided-clocks = <&atl_clkin0_ck>, <&atl_clkin1_ck>, + <&atl_clkin2_ck>, <&atl_clkin3_ck>; + clocks = <&atl_gfclk_mux>; + clock-names = "fck"; +}; + +#include <dt-bindings/clk/ti-dra7-atl.h> + +&atl { + + atl2 { + bws = <DRA7_ATL_WS_MCASP2_FSX>; + aws = <DRA7_ATL_WS_MCASP3_FSX>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/ti/fapll.txt b/Documentation/devicetree/bindings/clock/ti/fapll.txt new file mode 100644 index 000000000..c19b3f253 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/fapll.txt @@ -0,0 +1,33 @@ +Binding for Texas Instruments FAPLL clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped FAPLL with usually two selectable input clocks +(reference clock and bypass clock), and one or more child +syntesizers. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,dm816-fapll-clock" +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of parent clocks (clk-ref and clk-bypass) +- reg : address and length of the register set for controlling the FAPLL. + +Examples: + main_fapll: main_fapll { + #clock-cells = <1>; + compatible = "ti,dm816-fapll-clock"; + reg = <0x400 0x40>; + clocks = <&sys_clkin_ck &sys_clkin_ck>; + clock-indices = <1>, <2>, <3>, <4>, <5>, + <6>, <7>; + clock-output-names = "main_pll_clk1", + "main_pll_clk2", + "main_pll_clk3", + "main_pll_clk4", + "main_pll_clk5", + "main_pll_clk6", + "main_pll_clk7"; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/fixed-factor-clock.txt b/Documentation/devicetree/bindings/clock/ti/fixed-factor-clock.txt new file mode 100644 index 000000000..662b36d53 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/fixed-factor-clock.txt @@ -0,0 +1,43 @@ +Binding for TI fixed factor rate clock sources. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1], and also uses the autoidle +support from TI autoidle clock [2]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/ti/autoidle.txt + +Required properties: +- compatible : shall be "ti,fixed-factor-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- ti,clock-div: fixed divider. +- ti,clock-mult: fixed multiplier. +- clocks: parent clock. + +Optional properties: +- ti,autoidle-shift: bit shift of the autoidle enable bit for the clock, + see [2] +- reg: offset for the autoidle register of this clock, see [2] +- ti,invert-autoidle-bit: autoidle is enabled by setting the bit to 0, see [2] +- ti,set-rate-parent: clk_set_rate is propagated to parent + +Example: + clock { + compatible = "ti,fixed-factor-clock"; + clocks = <&parentclk>; + #clock-cells = <0>; + ti,clock-div = <2>; + ti,clock-mult = <1>; + }; + + dpll_usb_clkdcoldo_ck: dpll_usb_clkdcoldo_ck { + #clock-cells = <0>; + compatible = "ti,fixed-factor-clock"; + clocks = <&dpll_usb_ck>; + ti,clock-div = <1>; + ti,autoidle-shift = <8>; + reg = <0x01b4>; + ti,clock-mult = <1>; + ti,invert-autoidle-bit; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/gate.txt b/Documentation/devicetree/bindings/clock/ti/gate.txt new file mode 100644 index 000000000..56d603c1f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/gate.txt @@ -0,0 +1,106 @@ +Binding for Texas Instruments gate clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. This clock is +quite much similar to the basic gate-clock [2], however, +it supports a number of additional features. If no register +is provided for this clock, the code assumes that a clockdomain +will be controlled instead and the corresponding hw-ops for +that is used. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/gpio-gate-clock.txt +[3] Documentation/devicetree/bindings/clock/ti/clockdomain.txt + +Required properties: +- compatible : shall be one of: + "ti,gate-clock" - basic gate clock + "ti,wait-gate-clock" - gate clock which waits until clock is active before + returning from clk_enable() + "ti,dss-gate-clock" - gate clock with DSS specific hardware handling + "ti,am35xx-gate-clock" - gate clock with AM35xx specific hardware handling + "ti,clkdm-gate-clock" - clockdomain gate clock, which derives its functional + clock directly from a clockdomain, see [3] how + to map clockdomains properly + "ti,hsdiv-gate-clock" - gate clock with OMAP36xx specific hardware handling, + required for a hardware errata + "ti,composite-gate-clock" - composite gate clock, to be part of composite + clock + "ti,composite-no-wait-gate-clock" - composite gate clock that does not wait + for clock to be active before returning + from clk_enable() +- #clock-cells : from common clock binding; shall be set to 0 +- clocks : link to phandle of parent clock +- reg : offset for register controlling adjustable gate, not needed for + ti,clkdm-gate-clock type + +Optional properties: +- ti,bit-shift : bit shift for programming the clock gate, invalid for + ti,clkdm-gate-clock type +- ti,set-bit-to-disable : inverts default gate programming. Setting the bit + gates the clock and clearing the bit ungates the clock. + +Examples: + mmchs2_fck: mmchs2_fck@48004a00 { + #clock-cells = <0>; + compatible = "ti,gate-clock"; + clocks = <&core_96m_fck>; + reg = <0x0a00>; + ti,bit-shift = <25>; + }; + + uart4_fck_am35xx: uart4_fck_am35xx { + #clock-cells = <0>; + compatible = "ti,wait-gate-clock"; + clocks = <&core_48m_fck>; + reg = <0x0a00>; + ti,bit-shift = <23>; + }; + + dss1_alwon_fck_3430es2: dss1_alwon_fck_3430es2@48004e00 { + #clock-cells = <0>; + compatible = "ti,dss-gate-clock"; + clocks = <&dpll4_m4x2_ck>; + reg = <0x0e00>; + ti,bit-shift = <0>; + }; + + emac_ick: emac_ick@4800259c { + #clock-cells = <0>; + compatible = "ti,am35xx-gate-clock"; + clocks = <&ipss_ick>; + reg = <0x059c>; + ti,bit-shift = <1>; + }; + + emu_src_ck: emu_src_ck { + #clock-cells = <0>; + compatible = "ti,clkdm-gate-clock"; + clocks = <&emu_src_mux_ck>; + }; + + dpll4_m2x2_ck: dpll4_m2x2_ck@48004d00 { + #clock-cells = <0>; + compatible = "ti,hsdiv-gate-clock"; + clocks = <&dpll4_m2x2_mul_ck>; + ti,bit-shift = <0x1b>; + reg = <0x0d00>; + ti,set-bit-to-disable; + }; + + vlynq_gate_fck: vlynq_gate_fck { + #clock-cells = <0>; + compatible = "ti,composite-gate-clock"; + clocks = <&core_ck>; + ti,bit-shift = <3>; + reg = <0x0200>; + }; + + sys_clkout2_src_gate: sys_clkout2_src_gate { + #clock-cells = <0>; + compatible = "ti,composite-no-wait-gate-clock"; + clocks = <&core_ck>; + ti,bit-shift = <15>; + reg = <0x0070>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/interface.txt b/Documentation/devicetree/bindings/clock/ti/interface.txt new file mode 100644 index 000000000..3f4704040 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/interface.txt @@ -0,0 +1,56 @@ +Binding for Texas Instruments interface clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. This clock is +quite much similar to the basic gate-clock [2], however, +it supports a number of additional features, including +companion clock finding (match corresponding functional gate +clock) and hardware autoidle enable / disable. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/gpio-gate-clock.txt + +Required properties: +- compatible : shall be one of: + "ti,omap3-interface-clock" - basic OMAP3 interface clock + "ti,omap3-no-wait-interface-clock" - interface clock which has no hardware + capability for waiting clock to be ready + "ti,omap3-hsotgusb-interface-clock" - interface clock with USB specific HW + handling + "ti,omap3-dss-interface-clock" - interface clock with DSS specific HW handling + "ti,omap3-ssi-interface-clock" - interface clock with SSI specific HW handling + "ti,am35xx-interface-clock" - interface clock with AM35xx specific HW handling + "ti,omap2430-interface-clock" - interface clock with OMAP2430 specific HW + handling +- #clock-cells : from common clock binding; shall be set to 0 +- clocks : link to phandle of parent clock +- reg : base address for the control register + +Optional properties: +- ti,bit-shift : bit shift for the bit enabling/disabling the clock (default 0) + +Examples: + aes1_ick: aes1_ick@48004a14 { + #clock-cells = <0>; + compatible = "ti,omap3-interface-clock"; + clocks = <&security_l4_ick2>; + reg = <0x48004a14 0x4>; + ti,bit-shift = <3>; + }; + + cam_ick: cam_ick@48004f10 { + #clock-cells = <0>; + compatible = "ti,omap3-no-wait-interface-clock"; + clocks = <&l4_ick>; + reg = <0x48004f10 0x4>; + ti,bit-shift = <0>; + }; + + ssi_ick_3430es2: ssi_ick_3430es2@48004a10 { + #clock-cells = <0>; + compatible = "ti,omap3-ssi-interface-clock"; + clocks = <&ssi_l4_ick>; + reg = <0x48004a10 0x4>; + ti,bit-shift = <0>; + }; diff --git a/Documentation/devicetree/bindings/clock/ti/mux.txt b/Documentation/devicetree/bindings/clock/ti/mux.txt new file mode 100644 index 000000000..eec8994b9 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ti/mux.txt @@ -0,0 +1,79 @@ +Binding for TI mux clock. + +Binding status: Unstable - ABI compatibility may be broken in the future + +This binding uses the common clock binding[1]. It assumes a +register-mapped multiplexer with multiple input clock signals or +parents, one of which can be selected as output. This clock does not +gate or adjust the parent rate via a divider or multiplier. + +By default the "clocks" property lists the parents in the same order +as they are programmed into the regster. E.g: + + clocks = <&foo_clock>, <&bar_clock>, <&baz_clock>; + +results in programming the register as follows: + +register value selected parent clock +0 foo_clock +1 bar_clock +2 baz_clock + +Some clock controller IPs do not allow a value of zero to be programmed +into the register, instead indexing begins at 1. The optional property +"index-starts-at-one" modified the scheme as follows: + +register value selected clock parent +1 foo_clock +2 bar_clock +3 baz_clock + +The binding must provide the register to control the mux. Optionally +the number of bits to shift the control field in the register can be +supplied. If the shift value is missing it is the same as supplying +a zero shift. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be "ti,mux-clock" or "ti,composite-mux-clock". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : link phandles of parent clocks +- reg : register offset for register controlling adjustable mux + +Optional properties: +- ti,bit-shift : number of bits to shift the bit-mask, defaults to + 0 if not present +- ti,index-starts-at-one : valid input select programming starts at 1, not + zero +- ti,set-rate-parent : clk_set_rate is propagated to parent clock, + not supported by the composite-mux-clock subtype +- ti,latch-bit : latch the mux value to HW, only needed if the register + access requires this. As an example, dra7x DPLL_GMAC H14 muxing + implements such behavior. + +Examples: + +sys_clkin_ck: sys_clkin_ck@4a306110 { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&virt_12000000_ck>, <&virt_13000000_ck>, <&virt_16800000_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_27000000_ck>, <&virt_38400000_ck>; + reg = <0x0110>; + ti,index-starts-at-one; +}; + +abe_dpll_bypass_clk_mux_ck: abe_dpll_bypass_clk_mux_ck@4a306108 { + #clock-cells = <0>; + compatible = "ti,mux-clock"; + clocks = <&sys_clkin_ck>, <&sys_32k_ck>; + ti,bit-shift = <24>; + reg = <0x0108>; +}; + +mcbsp5_mux_fck: mcbsp5_mux_fck { + #clock-cells = <0>; + compatible = "ti,composite-mux-clock"; + clocks = <&core_96m_fck>, <&mcbsp_clks>; + ti,bit-shift = <4>; + reg = <0x02d8>; +}; diff --git a/Documentation/devicetree/bindings/clock/uniphier-clock.txt b/Documentation/devicetree/bindings/clock/uniphier-clock.txt new file mode 100644 index 000000000..7b5f60276 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/uniphier-clock.txt @@ -0,0 +1,132 @@ +UniPhier clock controller + + +System clock +------------ + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-ld4-clock" - for LD4 SoC. + "socionext,uniphier-pro4-clock" - for Pro4 SoC. + "socionext,uniphier-sld8-clock" - for sLD8 SoC. + "socionext,uniphier-pro5-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-clock" - for LD11 SoC. + "socionext,uniphier-ld20-clock" - for LD20 SoC. + "socionext,uniphier-pxs3-clock" - for PXs3 SoC +- #clock-cells: should be 1. + +Example: + + sysctrl@61840000 { + compatible = "socionext,uniphier-sysctrl", + "simple-mfd", "syscon"; + reg = <0x61840000 0x4000>; + + clock { + compatible = "socionext,uniphier-ld11-clock"; + #clock-cells = <1>; + }; + + other nodes ... + }; + +Provided clocks: + + 8: ST DMAC +12: GIO (Giga bit stream I/O) +14: USB3 ch0 host +15: USB3 ch1 host +16: USB3 ch0 PHY0 +17: USB3 ch0 PHY1 +20: USB3 ch1 PHY0 +21: USB3 ch1 PHY1 + + +Media I/O (MIO) clock, SD clock +------------------------------- + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-ld4-mio-clock" - for LD4 SoC. + "socionext,uniphier-pro4-mio-clock" - for Pro4 SoC. + "socionext,uniphier-sld8-mio-clock" - for sLD8 SoC. + "socionext,uniphier-pro5-sd-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-sd-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-mio-clock" - for LD11 SoC. + "socionext,uniphier-ld20-sd-clock" - for LD20 SoC. + "socionext,uniphier-pxs3-sd-clock" - for PXs3 SoC +- #clock-cells: should be 1. + +Example: + + mioctrl@59810000 { + compatible = "socionext,uniphier-mioctrl", + "simple-mfd", "syscon"; + reg = <0x59810000 0x800>; + + clock { + compatible = "socionext,uniphier-ld11-mio-clock"; + #clock-cells = <1>; + }; + + other nodes ... + }; + +Provided clocks: + + 0: SD ch0 host + 1: eMMC host + 2: SD ch1 host + 7: MIO DMAC + 8: USB2 ch0 host + 9: USB2 ch1 host +10: USB2 ch2 host +12: USB2 ch0 PHY +13: USB2 ch1 PHY +14: USB2 ch2 PHY + + +Peripheral clock +---------------- + +Required properties: +- compatible: should be one of the following: + "socionext,uniphier-ld4-peri-clock" - for LD4 SoC. + "socionext,uniphier-pro4-peri-clock" - for Pro4 SoC. + "socionext,uniphier-sld8-peri-clock" - for sLD8 SoC. + "socionext,uniphier-pro5-peri-clock" - for Pro5 SoC. + "socionext,uniphier-pxs2-peri-clock" - for PXs2/LD6b SoC. + "socionext,uniphier-ld11-peri-clock" - for LD11 SoC. + "socionext,uniphier-ld20-peri-clock" - for LD20 SoC. + "socionext,uniphier-pxs3-peri-clock" - for PXs3 SoC +- #clock-cells: should be 1. + +Example: + + perictrl@59820000 { + compatible = "socionext,uniphier-perictrl", + "simple-mfd", "syscon"; + reg = <0x59820000 0x200>; + + clock { + compatible = "socionext,uniphier-ld11-peri-clock"; + #clock-cells = <1>; + }; + + other nodes ... + }; + +Provided clocks: + + 0: UART ch0 + 1: UART ch1 + 2: UART ch2 + 3: UART ch3 + 4: I2C ch0 + 5: I2C ch1 + 6: I2C ch2 + 7: I2C ch3 + 8: I2C ch4 + 9: I2C ch5 +10: I2C ch6 diff --git a/Documentation/devicetree/bindings/clock/ux500.txt b/Documentation/devicetree/bindings/clock/ux500.txt new file mode 100644 index 000000000..e52bd4b72 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/ux500.txt @@ -0,0 +1,64 @@ +Clock bindings for ST-Ericsson Ux500 clocks + +Required properties : +- compatible : shall contain only one of the following: + "stericsson,u8500-clks" + "stericsson,u8540-clks" + "stericsson,u9540-clks" +- reg : shall contain base register location and length for + CLKRST1, 2, 3, 5, and 6 in an array. Note the absence of + CLKRST4, which does not exist. + +Required subnodes: +- prcmu-clock: a subnode with one clock cell for PRCMU (power, + reset, control unit) clocks. The cell indicates which PRCMU + clock in the prcmu-clock node the consumer wants to use. +- prcc-periph-clock: a subnode with two clock cells for + PRCC (programmable reset- and clock controller) peripheral clocks. + The first cell indicates which PRCC block the consumer + wants to use, possible values are 1, 2, 3, 5, 6. The second + cell indicates which clock inside the PRCC block it wants, + possible values are 0 thru 31. +- prcc-kernel-clock: a subnode with two clock cells for + PRCC (programmable reset- and clock controller) kernel clocks + The first cell indicates which PRCC block the consumer + wants to use, possible values are 1, 2, 3, 5, 6. The second + cell indicates which clock inside the PRCC block it wants, + possible values are 0 thru 31. +- rtc32k-clock: a subnode with zero clock cells for the 32kHz + RTC clock. +- smp-twd-clock: a subnode for the ARM SMP Timer Watchdog cluster + with zero clock cells. + +Example: + +clocks { + compatible = "stericsson,u8500-clks"; + /* + * Registers for the CLKRST block on peripheral + * groups 1, 2, 3, 5, 6, + */ + reg = <0x8012f000 0x1000>, <0x8011f000 0x1000>, + <0x8000f000 0x1000>, <0xa03ff000 0x1000>, + <0xa03cf000 0x1000>; + + prcmu_clk: prcmu-clock { + #clock-cells = <1>; + }; + + prcc_pclk: prcc-periph-clock { + #clock-cells = <2>; + }; + + prcc_kclk: prcc-kernel-clock { + #clock-cells = <2>; + }; + + rtc_clk: rtc32k-clock { + #clock-cells = <0>; + }; + + smp_twd_clk: smp-twd-clock { + #clock-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/clock/vf610-clock.txt b/Documentation/devicetree/bindings/clock/vf610-clock.txt new file mode 100644 index 000000000..63f9f1ac3 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/vf610-clock.txt @@ -0,0 +1,41 @@ +* Clock bindings for Freescale Vybrid VF610 SOC + +Required properties: +- compatible: Should be "fsl,vf610-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> + +Optional properties: +- clocks: list of clock identifiers which are external input clocks to the + given clock controller. Please refer the next section to find + the input clocks for a given controller. +- clock-names: list of names of clocks which are exteral input clocks to the + given clock controller. + +Input clocks for top clock controller: + - sxosc (external crystal oscillator 32KHz, recommended) + - fxosc (external crystal oscillator 24MHz, recommended) + - audio_ext + - enet_ext + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/vf610-clock.h +for the full list of VF610 clock IDs. + +Examples: + +clks: ccm@4006b000 { + compatible = "fsl,vf610-ccm"; + reg = <0x4006b000 0x1000>; + #clock-cells = <1>; + clocks = <&sxosc>, <&fxosc>; + clock-names = "sxosc", "fxosc"; +}; + +uart1: serial@40028000 { + compatible = "fsl,vf610-uart"; + reg = <0x40028000 0x1000>; + interrupts = <0 62 0x04>; + clocks = <&clks VF610_CLK_UART1>; + clock-names = "ipg"; +}; diff --git a/Documentation/devicetree/bindings/clock/vt8500.txt b/Documentation/devicetree/bindings/clock/vt8500.txt new file mode 100644 index 000000000..91d71cc03 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/vt8500.txt @@ -0,0 +1,74 @@ +Device Tree Clock bindings for arch-vt8500 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "via,vt8500-pll-clock" - for a VT8500/WM8505 PLL clock + "wm,wm8650-pll-clock" - for a WM8650 PLL clock + "wm,wm8750-pll-clock" - for a WM8750 PLL clock + "wm,wm8850-pll-clock" - for a WM8850 PLL clock + "via,vt8500-device-clock" - for a VT/WM device clock + +Required properties for PLL clocks: +- reg : shall be the control register offset from PMC base for the pll clock. +- clocks : shall be the input parent clock phandle for the clock. This should + be the reference clock. +- #clock-cells : from common clock binding; shall be set to 0. + +Required properties for device clocks: +- clocks : shall be the input parent clock phandle for the clock. This should + be a pll output. +- #clock-cells : from common clock binding; shall be set to 0. + + +Device Clocks + +Device clocks are required to have one or both of the following sets of +properties: + + +Gated device clocks: + +Required properties: +- enable-reg : shall be the register offset from PMC base for the enable + register. +- enable-bit : shall be the bit within enable-reg to enable/disable the clock. + + +Divisor device clocks: + +Required property: +- divisor-reg : shall be the register offset from PMC base for the divisor + register. +Optional property: +- divisor-mask : shall be the mask for the divisor register. Defaults to 0x1f + if not specified. + + +For example: + +ref25: ref25M { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; +}; + +plla: plla { + #clock-cells = <0>; + compatible = "wm,wm8650-pll-clock"; + clocks = <&ref25>; + reg = <0x200>; +}; + +sdhc: sdhc { + #clock-cells = <0>; + compatible = "via,vt8500-device-clock"; + clocks = <&pllb>; + divisor-reg = <0x328>; + divisor-mask = <0x3f>; + enable-reg = <0x254>; + enable-bit = <18>; +}; diff --git a/Documentation/devicetree/bindings/clock/xgene.txt b/Documentation/devicetree/bindings/clock/xgene.txt new file mode 100644 index 000000000..8233e7717 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/xgene.txt @@ -0,0 +1,131 @@ +Device Tree Clock bindings for APM X-Gene + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "apm,xgene-socpll-clock" - for a X-Gene SoC PLL clock + "apm,xgene-pcppll-clock" - for a X-Gene PCP PLL clock + "apm,xgene-pmd-clock" - for a X-Gene PMD clock + "apm,xgene-device-clock" - for a X-Gene device clock + "apm,xgene-socpll-v2-clock" - for a X-Gene SoC PLL v2 clock + "apm,xgene-pcppll-v2-clock" - for a X-Gene PCP PLL v2 clock + +Required properties for SoC or PCP PLL clocks: +- reg : shall be the physical PLL register address for the pll clock. +- clocks : shall be the input parent clock phandle for the clock. This should + be the reference clock. +- #clock-cells : shall be set to 1. +- clock-output-names : shall be the name of the PLL referenced by derive + clock. +Optional properties for PLL clocks: +- clock-names : shall be the name of the PLL. If missing, use the device name. + +Required properties for PMD clocks: +- reg : shall be the physical register address for the pmd clock. +- clocks : shall be the input parent clock phandle for the clock. +- #clock-cells : shall be set to 1. +- clock-output-names : shall be the name of the clock referenced by derive + clock. +Optional properties for PLL clocks: +- clock-names : shall be the name of the clock. If missing, use the device name. + +Required properties for device clocks: +- reg : shall be a list of address and length pairs describing the CSR + reset and/or the divider. Either may be omitted, but at least + one must be present. + - reg-names : shall be a string list describing the reg resource. This + may include "csr-reg" and/or "div-reg". If this property + is not present, the reg property is assumed to describe + only "csr-reg". +- clocks : shall be the input parent clock phandle for the clock. +- #clock-cells : shall be set to 1. +- clock-output-names : shall be the name of the device referenced. +Optional properties for device clocks: +- clock-names : shall be the name of the device clock. If missing, use the + device name. +- csr-offset : Offset to the CSR reset register from the reset address base. + Default is 0. +- csr-mask : CSR reset mask bit. Default is 0xF. +- enable-offset : Offset to the enable register from the reset address base. + Default is 0x8. +- enable-mask : CSR enable mask bit. Default is 0xF. +- divider-offset : Offset to the divider CSR register from the divider base. + Default is 0x0. +- divider-width : Width of the divider register. Default is 0. +- divider-shift : Bit shift of the divider register. Default is 0. + +For example: + + pcppll: pcppll@17000100 { + compatible = "apm,xgene-pcppll-clock"; + #clock-cells = <1>; + clocks = <&refclk 0>; + clock-names = "pcppll"; + reg = <0x0 0x17000100 0x0 0x1000>; + clock-output-names = "pcppll"; + type = <0>; + }; + + pmd0clk: pmd0clk@7e200200 { + compatible = "apm,xgene-pmd-clock"; + #clock-cells = <1>; + clocks = <&pmdpll 0>; + reg = <0x0 0x7e200200 0x0 0x10>; + clock-output-names = "pmd0clk"; + }; + + socpll: socpll@17000120 { + compatible = "apm,xgene-socpll-clock"; + #clock-cells = <1>; + clocks = <&refclk 0>; + clock-names = "socpll"; + reg = <0x0 0x17000120 0x0 0x1000>; + clock-output-names = "socpll"; + type = <1>; + }; + + qmlclk: qmlclk { + compatible = "apm,xgene-device-clock"; + #clock-cells = <1>; + clocks = <&socplldiv2 0>; + clock-names = "qmlclk"; + reg = <0x0 0x1703C000 0x0 0x1000>; + reg-name = "csr-reg"; + clock-output-names = "qmlclk"; + }; + + ethclk: ethclk { + compatible = "apm,xgene-device-clock"; + #clock-cells = <1>; + clocks = <&socplldiv2 0>; + clock-names = "ethclk"; + reg = <0x0 0x17000000 0x0 0x1000>; + reg-names = "div-reg"; + divider-offset = <0x238>; + divider-width = <0x9>; + divider-shift = <0x0>; + clock-output-names = "ethclk"; + }; + + apbclk: apbclk { + compatible = "apm,xgene-device-clock"; + #clock-cells = <1>; + clocks = <&ahbclk 0>; + clock-names = "apbclk"; + reg = <0x0 0x1F2AC000 0x0 0x1000 + 0x0 0x1F2AC000 0x0 0x1000>; + reg-names = "csr-reg", "div-reg"; + csr-offset = <0x0>; + csr-mask = <0x200>; + enable-offset = <0x8>; + enable-mask = <0x200>; + divider-offset = <0x10>; + divider-width = <0x2>; + divider-shift = <0x0>; + flags = <0x8>; + clock-output-names = "apbclk"; + }; + diff --git a/Documentation/devicetree/bindings/clock/zx296702-clk.txt b/Documentation/devicetree/bindings/clock/zx296702-clk.txt new file mode 100644 index 000000000..5c91c9e4f --- /dev/null +++ b/Documentation/devicetree/bindings/clock/zx296702-clk.txt @@ -0,0 +1,34 @@ +Device Tree Clock bindings for ZTE zx296702 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "zte,zx296702-topcrm-clk": + zx296702 top clock selection, divider and gating + + "zte,zx296702-lsp0crpm-clk" and + "zte,zx296702-lsp1crpm-clk": + zx296702 device level clock selection and gating + +- reg: Address and length of the register set + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/zx296702-clock.h +for the full list of zx296702 clock IDs. + + +topclk: topcrm@09800000 { + compatible = "zte,zx296702-topcrm-clk"; + reg = <0x09800000 0x1000>; + #clock-cells = <1>; +}; + +uart0: serial@09405000 { + compatible = "zte,zx296702-uart"; + reg = <0x09405000 0x1000>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&lsp1clk ZX296702_UART0_PCLK>; +}; diff --git a/Documentation/devicetree/bindings/clock/zx296718-clk.txt b/Documentation/devicetree/bindings/clock/zx296718-clk.txt new file mode 100644 index 000000000..3a46bf0b2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/zx296718-clk.txt @@ -0,0 +1,37 @@ +Device Tree Clock bindings for ZTE zx296718 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "zte,zx296718-topcrm": + zx296718 top clock selection, divider and gating + + "zte,zx296718-lsp0crm" and + "zte,zx296718-lsp1crm": + zx296718 device level clock selection and gating + + "zte,zx296718-audiocrm": + zx296718 audio clock selection, divider and gating + +- reg: Address and length of the register set + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/zx296718-clock.h +for the full list of zx296718 clock IDs. + + +topclk: topcrm@1461000 { + compatible = "zte,zx296718-topcrm-clk"; + reg = <0x01461000 0x1000>; + #clock-cells = <1>; +}; + +usbphy0:usb-phy0 { + compatible = "zte,zx296718-usb-phy"; + #phy-cells = <0>; + clocks = <&topclk USB20_PHY_CLK>; + clock-names = "phyclk"; +}; diff --git a/Documentation/devicetree/bindings/clock/zynq-7000.txt b/Documentation/devicetree/bindings/clock/zynq-7000.txt new file mode 100644 index 000000000..d93746cf2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/zynq-7000.txt @@ -0,0 +1,110 @@ +Device Tree Clock bindings for the Zynq 7000 EPP + +The Zynq EPP has several different clk providers, each with there own bindings. +The purpose of this document is to document their usage. + +See clock_bindings.txt for more information on the generic clock bindings. +See Chapter 25 of Zynq TRM for more information about Zynq clocks. + +== Clock Controller == +The clock controller is a logical abstraction of Zynq's clock tree. It reads +required input clock frequencies from the devicetree and acts as clock provider +for all clock consumers of PS clocks. + +Required properties: + - #clock-cells : Must be 1 + - compatible : "xlnx,ps7-clkc" + - reg : SLCR offset and size taken via syscon < 0x100 0x100 > + - ps-clk-frequency : Frequency of the oscillator providing ps_clk in HZ + (usually 33 MHz oscillators are used for Zynq platforms) + - clock-output-names : List of strings used to name the clock outputs. Shall be + a list of the outputs given below. + +Optional properties: + - clocks : as described in the clock bindings + - clock-names : as described in the clock bindings + - fclk-enable : Bit mask to enable FCLKs statically at boot time. + Bit [0..3] correspond to FCLK0..FCLK3. The corresponding + FCLK will only be enabled if it is actually running at + boot time. + +Clock inputs: +The following strings are optional parameters to the 'clock-names' property in +order to provide an optional (E)MIO clock source. + - swdt_ext_clk + - gem0_emio_clk + - gem1_emio_clk + - mio_clk_XX # with XX = 00..53 +... + +Clock outputs: + 0: armpll + 1: ddrpll + 2: iopll + 3: cpu_6or4x + 4: cpu_3or2x + 5: cpu_2x + 6: cpu_1x + 7: ddr2x + 8: ddr3x + 9: dci + 10: lqspi + 11: smc + 12: pcap + 13: gem0 + 14: gem1 + 15: fclk0 + 16: fclk1 + 17: fclk2 + 18: fclk3 + 19: can0 + 20: can1 + 21: sdio0 + 22: sdio1 + 23: uart0 + 24: uart1 + 25: spi0 + 26: spi1 + 27: dma + 28: usb0_aper + 29: usb1_aper + 30: gem0_aper + 31: gem1_aper + 32: sdio0_aper + 33: sdio1_aper + 34: spi0_aper + 35: spi1_aper + 36: can0_aper + 37: can1_aper + 38: i2c0_aper + 39: i2c1_aper + 40: uart0_aper + 41: uart1_aper + 42: gpio_aper + 43: lqspi_aper + 44: smc_aper + 45: swdt + 46: dbg_trc + 47: dbg_apb + +Example: + clkc: clkc@100 { + #clock-cells = <1>; + compatible = "xlnx,ps7-clkc"; + ps-clk-frequency = <33333333>; + reg = <0x100 0x100>; + clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x", + "cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x", + "dci", "lqspi", "smc", "pcap", "gem0", "gem1", + "fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1", + "sdio0", "sdio1", "uart0", "uart1", "spi0", "spi1", + "dma", "usb0_aper", "usb1_aper", "gem0_aper", + "gem1_aper", "sdio0_aper", "sdio1_aper", + "spi0_aper", "spi1_aper", "can0_aper", "can1_aper", + "i2c0_aper", "i2c1_aper", "uart0_aper", "uart1_aper", + "gpio_aper", "lqspi_aper", "smc_aper", "swdt", + "dbg_trc", "dbg_apb"; + # optional props + clocks = <&clkc 16>, <&clk_foo>; + clock-names = "gem1_emio_clk", "can_mio_clk_23"; + }; |