diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/display/msm/dpu.txt | 131 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/display/msm/dsi.txt | 244 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/display/msm/edp.txt | 56 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/display/msm/gpu.txt | 38 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/display/msm/hdmi.txt | 99 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/display/msm/mdp4.txt | 112 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/display/msm/mdp5.txt | 158 |
7 files changed, 838 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/msm/dpu.txt b/Documentation/devicetree/bindings/display/msm/dpu.txt new file mode 100644 index 000000000..ad2e88303 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dpu.txt @@ -0,0 +1,131 @@ +Qualcomm Technologies, Inc. DPU KMS + +Description: + +Device tree bindings for MSM Mobile Display Subsytem(MDSS) that encapsulates +sub-blocks like DPU display controller, DSI and DP interfaces etc. +The DPU display controller is found in SDM845 SoC. + +MDSS: +Required properties: +- compatible: "qcom,sdm845-mdss" +- reg: physical base address and length of contoller's registers. +- reg-names: register region names. The following region is required: + * "mdss" +- power-domains: a power domain consumer specifier according to + Documentation/devicetree/bindings/power/power_domain.txt +- clocks: list of clock specifiers for clocks needed by the device. +- clock-names: device clock names, must be in same order as clocks property. + The following clocks are required: + * "iface" + * "bus" + * "core" +- interrupts: interrupt signal from MDSS. +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- iommus: phandle of iommu device node. +- #address-cells: number of address cells for the MDSS children. Should be 1. +- #size-cells: Should be 1. +- ranges: parent bus address space is the same as the child bus address space. + +Optional properties: +- assigned-clocks: list of clock specifiers for clocks needing rate assignment +- assigned-clock-rates: list of clock frequencies sorted in the same order as + the assigned-clocks property. + +MDP: +Required properties: +- compatible: "qcom,sdm845-dpu" +- reg: physical base address and length of controller's registers. +- reg-names : register region names. The following region is required: + * "mdp" + * "vbif" +- clocks: list of clock specifiers for clocks needed by the device. +- clock-names: device clock names, must be in same order as clocks property. + The following clocks are required. + * "bus" + * "iface" + * "core" + * "vsync" +- interrupts: interrupt line from DPU to MDSS. +- ports: contains the list of output ports from DPU device. These ports connect + to interfaces that are external to the DPU hardware, such as DSI, DP etc. + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + Port 0 -> DPU_INTF1 (DSI1) + Port 1 -> DPU_INTF2 (DSI2) + +Optional properties: +- assigned-clocks: list of clock specifiers for clocks needing rate assignment +- assigned-clock-rates: list of clock frequencies sorted in the same order as + the assigned-clocks property. + +Example: + + mdss: mdss@ae00000 { + compatible = "qcom,sdm845-mdss"; + reg = <0xae00000 0x1000>; + reg-names = "mdss"; + + power-domains = <&clock_dispcc 0>; + + clocks = <&gcc GCC_DISP_AHB_CLK>, <&gcc GCC_DISP_AXI_CLK>, + <&clock_dispcc DISP_CC_MDSS_MDP_CLK>; + clock-names = "iface", "bus", "core"; + + assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>; + assigned-clock-rates = <300000000>; + + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + + iommus = <&apps_iommu 0>; + + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0xae00000 0xb2008>; + + mdss_mdp: mdp@ae01000 { + compatible = "qcom,sdm845-dpu"; + reg = <0 0x1000 0x8f000>, <0 0xb0000 0x2008>; + reg-names = "mdp", "vbif"; + + clocks = <&clock_dispcc DISP_CC_MDSS_AHB_CLK>, + <&clock_dispcc DISP_CC_MDSS_AXI_CLK>, + <&clock_dispcc DISP_CC_MDSS_MDP_CLK>, + <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>; + clock-names = "iface", "bus", "core", "vsync"; + + assigned-clocks = <&clock_dispcc DISP_CC_MDSS_MDP_CLK>, + <&clock_dispcc DISP_CC_MDSS_VSYNC_CLK>; + assigned-clock-rates = <0 0 300000000 19200000>; + + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + + port@1 { + reg = <1>; + dpu_intf2_out: endpoint { + remote-endpoint = <&dsi1_in>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/msm/dsi.txt b/Documentation/devicetree/bindings/display/msm/dsi.txt new file mode 100644 index 000000000..dfc743219 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/dsi.txt @@ -0,0 +1,244 @@ +Qualcomm Technologies Inc. adreno/snapdragon DSI output + +DSI Controller: +Required properties: +- compatible: + * "qcom,mdss-dsi-ctrl" +- reg: Physical base address and length of the registers of controller +- reg-names: The names of register regions. The following regions are required: + * "dsi_ctrl" +- interrupts: The interrupt signal from the DSI block. +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: Phandles to device clocks. +- clock-names: the following clocks are required: + * "mdp_core" + * "iface" + * "bus" + * "core_mmss" + * "byte" + * "pixel" + * "core" + For DSIv2, we need an additional clock: + * "src" + For DSI6G v2.0 onwards, we need also need the clock: + * "byte_intf" +- assigned-clocks: Parents of "byte" and "pixel" for the given platform. +- assigned-clock-parents: The Byte clock and Pixel clock PLL outputs provided + by a DSI PHY block. See [1] for details on clock bindings. +- vdd-supply: phandle to vdd regulator device node +- vddio-supply: phandle to vdd-io regulator device node +- vdda-supply: phandle to vdda regulator device node +- phys: phandle to DSI PHY device node +- phy-names: the name of the corresponding PHY device +- syscon-sfpb: A phandle to mmss_sfpb syscon node (only for DSIv2) +- ports: Contains 2 DSI controller ports as child nodes. Each port contains + an endpoint subnode as defined in [2] and [3]. + +Optional properties: +- panel@0: Node of panel connected to this DSI controller. + See files in [4] for each supported panel. +- qcom,dual-dsi-mode: Boolean value indicating if the DSI controller is + driving a panel which needs 2 DSI links. +- qcom,master-dsi: Boolean value indicating if the DSI controller is driving + the master link of the 2-DSI panel. +- qcom,sync-dual-dsi: Boolean value indicating if the DSI controller is + driving a 2-DSI panel whose 2 links need receive command simultaneously. +- pinctrl-names: the pin control state names; should contain "default" +- pinctrl-0: the default pinctrl state (active) +- pinctrl-n: the "sleep" pinctrl state +- ports: contains DSI controller input and output ports as children, each + containing one endpoint subnode. + + DSI Endpoint properties: + - remote-endpoint: For port@0, set to phandle of the connected panel/bridge's + input endpoint. For port@1, set to the MDP interface output. See [2] for + device graph info. + + - data-lanes: this describes how the physical DSI data lanes are mapped + to the logical lanes on the given platform. The value contained in + index n describes what physical lane is mapped to the logical lane n + (DATAn, where n lies between 0 and 3). The clock lane position is fixed + and can't be changed. Hence, they aren't a part of the DT bindings. See + [3] for more info on the data-lanes property. + + For example: + + data-lanes = <3 0 1 2>; + + The above mapping describes that the logical data lane DATA0 is mapped to + the physical data lane DATA3, logical DATA1 to physical DATA0, logic DATA2 + to phys DATA1 and logic DATA3 to phys DATA2. + + There are only a limited number of physical to logical mappings possible: + <0 1 2 3> + <1 2 3 0> + <2 3 0 1> + <3 0 1 2> + <0 3 2 1> + <1 0 3 2> + <2 1 0 3> + <3 2 1 0> + +DSI PHY: +Required properties: +- compatible: Could be the following + * "qcom,dsi-phy-28nm-hpm" + * "qcom,dsi-phy-28nm-lp" + * "qcom,dsi-phy-20nm" + * "qcom,dsi-phy-28nm-8960" + * "qcom,dsi-phy-14nm" + * "qcom,dsi-phy-10nm" +- reg: Physical base address and length of the registers of PLL, PHY. Some + revisions require the PHY regulator base address, whereas others require the + PHY lane base address. See below for each PHY revision. +- reg-names: The names of register regions. The following regions are required: + For DSI 28nm HPM/LP/8960 PHYs and 20nm PHY: + * "dsi_pll" + * "dsi_phy" + * "dsi_phy_regulator" + For DSI 14nm and 10nm PHYs: + * "dsi_pll" + * "dsi_phy" + * "dsi_phy_lane" +- clock-cells: Must be 1. The DSI PHY block acts as a clock provider, creating + 2 clocks: A byte clock (index 0), and a pixel clock (index 1). +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: Phandles to device clocks. See [1] for details on clock bindings. +- clock-names: the following clocks are required: + * "iface" + For 28nm HPM/LP, 28nm 8960 PHYs: +- vddio-supply: phandle to vdd-io regulator device node + For 20nm PHY: +- vddio-supply: phandle to vdd-io regulator device node +- vcca-supply: phandle to vcca regulator device node + For 14nm PHY: +- vcca-supply: phandle to vcca regulator device node + For 10nm PHY: +- vdds-supply: phandle to vdds regulator device node + +Optional properties: +- qcom,dsi-phy-regulator-ldo-mode: Boolean value indicating if the LDO mode PHY + regulator is wanted. +- qcom,mdss-mdp-transfer-time-us: Specifies the dsi transfer time for command mode + panels in microseconds. Driver uses this number to adjust + the clock rate according to the expected transfer time. + Increasing this value would slow down the mdp processing + and can result in slower performance. + Decreasing this value can speed up the mdp processing, + but this can also impact power consumption. + As a rule this time should not be higher than the time + that would be expected with the processing at the + dsi link rate since anyways this would be the maximum + transfer time that could be achieved. + If ping pong split is enabled, this time should not be higher + than two times the dsi link rate time. + If the property is not specified, then the default value is 14000 us. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/graph.txt +[3] Documentation/devicetree/bindings/media/video-interfaces.txt +[4] Documentation/devicetree/bindings/display/panel/ + +Example: + dsi0: dsi@fd922800 { + compatible = "qcom,mdss-dsi-ctrl"; + qcom,dsi-host-index = <0>; + interrupt-parent = <&mdp>; + interrupts = <4 0>; + reg-names = "dsi_ctrl"; + reg = <0xfd922800 0x200>; + power-domains = <&mmcc MDSS_GDSC>; + clock-names = + "bus", + "byte", + "core", + "core_mmss", + "iface", + "mdp_core", + "pixel"; + clocks = + <&mmcc MDSS_AXI_CLK>, + <&mmcc MDSS_BYTE0_CLK>, + <&mmcc MDSS_ESC0_CLK>, + <&mmcc MMSS_MISC_AHB_CLK>, + <&mmcc MDSS_AHB_CLK>, + <&mmcc MDSS_MDP_CLK>, + <&mmcc MDSS_PCLK0_CLK>; + + assigned-clocks = + <&mmcc BYTE0_CLK_SRC>, + <&mmcc PCLK0_CLK_SRC>; + assigned-clock-parents = + <&dsi_phy0 0>, + <&dsi_phy0 1>; + + vdda-supply = <&pma8084_l2>; + vdd-supply = <&pma8084_l22>; + vddio-supply = <&pma8084_l12>; + + phys = <&dsi_phy0>; + phy-names ="dsi-phy"; + + qcom,dual-dsi-mode; + qcom,master-dsi; + qcom,sync-dual-dsi; + + qcom,mdss-mdp-transfer-time-us = <12000>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dsi_active>; + pinctrl-1 = <&dsi_suspend>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; + + panel: panel@0 { + compatible = "sharp,lq101r1sx01"; + reg = <0>; + link2 = <&secondary>; + + power-supply = <...>; + backlight = <...>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; + }; + + dsi_phy0: dsi-phy@fd922a00 { + compatible = "qcom,dsi-phy-28nm-hpm"; + qcom,dsi-phy-index = <0>; + reg-names = + "dsi_pll", + "dsi_phy", + "dsi_phy_regulator"; + reg = <0xfd922a00 0xd4>, + <0xfd922b00 0x2b0>, + <0xfd922d80 0x7b>; + clock-names = "iface"; + clocks = <&mmcc MDSS_AHB_CLK>; + #clock-cells = <1>; + vddio-supply = <&pma8084_l12>; + + qcom,dsi-phy-regulator-ldo-mode; + }; diff --git a/Documentation/devicetree/bindings/display/msm/edp.txt b/Documentation/devicetree/bindings/display/msm/edp.txt new file mode 100644 index 000000000..eff9daff4 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/edp.txt @@ -0,0 +1,56 @@ +Qualcomm Technologies Inc. adreno/snapdragon eDP output + +Required properties: +- compatible: + * "qcom,mdss-edp" +- reg: Physical base address and length of the registers of controller and PLL +- reg-names: The names of register regions. The following regions are required: + * "edp" + * "pll_base" +- interrupts: The interrupt signal from the eDP block. +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "core" + * "iface" + * "mdp_core" + * "pixel" + * "link" +- #clock-cells: The value should be 1. +- vdda-supply: phandle to vdda regulator device node +- lvl-vdd-supply: phandle to regulator device node which is used to supply power + to HPD receiving chip +- panel-en-gpios: GPIO pin to supply power to panel. +- panel-hpd-gpios: GPIO pin used for eDP hpd. + + +Example: + mdss_edp: qcom,mdss_edp@fd923400 { + compatible = "qcom,mdss-edp"; + reg-names = + "edp", + "pll_base"; + reg = <0xfd923400 0x700>, + <0xfd923a00 0xd4>; + interrupt-parent = <&mdss_mdp>; + interrupts = <12 0>; + power-domains = <&mmcc MDSS_GDSC>; + clock-names = + "core", + "pixel", + "iface", + "link", + "mdp_core"; + clocks = + <&mmcc MDSS_EDPAUX_CLK>, + <&mmcc MDSS_EDPPIXEL_CLK>, + <&mmcc MDSS_AHB_CLK>, + <&mmcc MDSS_EDPLINK_CLK>, + <&mmcc MDSS_MDP_CLK>; + #clock-cells = <1>; + vdda-supply = <&pma8084_l12>; + lvl-vdd-supply = <&lvl_vreg>; + panel-en-gpios = <&tlmm 137 0>; + panel-hpd-gpios = <&tlmm 103 0>; + }; diff --git a/Documentation/devicetree/bindings/display/msm/gpu.txt b/Documentation/devicetree/bindings/display/msm/gpu.txt new file mode 100644 index 000000000..43fac0fe0 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/gpu.txt @@ -0,0 +1,38 @@ +Qualcomm adreno/snapdragon GPU + +Required properties: +- compatible: "qcom,adreno-XYZ.W", "qcom,adreno" + for example: "qcom,adreno-306.0", "qcom,adreno" + Note that you need to list the less specific "qcom,adreno" (since this + is what the device is matched on), in addition to the more specific + with the chip-id. +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the gpu. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required: + * "core" + * "iface" + * "mem_iface" + +Example: + +/ { + ... + + gpu: qcom,kgsl-3d0@4300000 { + compatible = "qcom,adreno-320.2", "qcom,adreno"; + reg = <0x04300000 0x20000>; + reg-names = "kgsl_3d0_reg_memory"; + interrupts = <GIC_SPI 80 0>; + interrupt-names = "kgsl_3d0_irq"; + clock-names = + "core", + "iface", + "mem_iface"; + clocks = + <&mmcc GFX3D_CLK>, + <&mmcc GFX3D_AHB_CLK>, + <&mmcc MMSS_IMEM_AHB_CLK>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/hdmi.txt b/Documentation/devicetree/bindings/display/msm/hdmi.txt new file mode 100644 index 000000000..5f90a40da --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/hdmi.txt @@ -0,0 +1,99 @@ +Qualcomm adreno/snapdragon hdmi output + +Required properties: +- compatible: one of the following + * "qcom,hdmi-tx-8996" + * "qcom,hdmi-tx-8994" + * "qcom,hdmi-tx-8084" + * "qcom,hdmi-tx-8974" + * "qcom,hdmi-tx-8660" + * "qcom,hdmi-tx-8960" +- reg: Physical base address and length of the controller's registers +- reg-names: "core_physical" +- interrupts: The interrupt signal from the hdmi block. +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- core-vdda-supply: phandle to supply regulator +- hdmi-mux-supply: phandle to mux regulator +- phys: the phandle for the HDMI PHY device +- phy-names: the name of the corresponding PHY device + +Optional properties: +- hpd-gpios: hpd pin +- qcom,hdmi-tx-mux-en-gpios: hdmi mux enable pin +- qcom,hdmi-tx-mux-sel-gpios: hdmi mux select pin +- qcom,hdmi-tx-mux-lpm-gpios: hdmi mux lpm pin +- power-domains: reference to the power domain(s), if available. +- pinctrl-names: the pin control state names; should contain "default" +- pinctrl-0: the default pinctrl state (active) +- pinctrl-1: the "sleep" pinctrl state + +HDMI PHY: +Required properties: +- compatible: Could be the following + * "qcom,hdmi-phy-8660" + * "qcom,hdmi-phy-8960" + * "qcom,hdmi-phy-8974" + * "qcom,hdmi-phy-8084" + * "qcom,hdmi-phy-8996" +- #phy-cells: Number of cells in a PHY specifier; Should be 0. +- reg: Physical base address and length of the registers of the PHY sub blocks. +- reg-names: The names of register regions. The following regions are required: + * "hdmi_phy" + * "hdmi_pll" + For HDMI PHY on msm8996, these additional register regions are required: + * "hdmi_tx_l0" + * "hdmi_tx_l1" + * "hdmi_tx_l3" + * "hdmi_tx_l4" +- power-domains: Should be <&mmcc MDSS_GDSC>. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- core-vdda-supply: phandle to vdda regulator device node + +Example: + +/ { + ... + + hdmi: hdmi@4a00000 { + compatible = "qcom,hdmi-tx-8960"; + reg-names = "core_physical"; + reg = <0x04a00000 0x2f0>; + interrupts = <GIC_SPI 79 0>; + power-domains = <&mmcc MDSS_GDSC>; + clock-names = + "core", + "master_iface", + "slave_iface"; + clocks = + <&mmcc HDMI_APP_CLK>, + <&mmcc HDMI_M_AHB_CLK>, + <&mmcc HDMI_S_AHB_CLK>; + qcom,hdmi-tx-ddc-clk = <&msmgpio 70 GPIO_ACTIVE_HIGH>; + qcom,hdmi-tx-ddc-data = <&msmgpio 71 GPIO_ACTIVE_HIGH>; + qcom,hdmi-tx-hpd = <&msmgpio 72 GPIO_ACTIVE_HIGH>; + core-vdda-supply = <&pm8921_hdmi_mvs>; + hdmi-mux-supply = <&ext_3p3v>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&hpd_active &ddc_active &cec_active>; + pinctrl-1 = <&hpd_suspend &ddc_suspend &cec_suspend>; + + phys = <&hdmi_phy>; + phy-names = "hdmi_phy"; + }; + + hdmi_phy: phy@4a00400 { + compatible = "qcom,hdmi-phy-8960"; + reg-names = "hdmi_phy", + "hdmi_pll"; + reg = <0x4a00400 0x60>, + <0x4a00500 0x100>; + #phy-cells = <0>; + power-domains = <&mmcc MDSS_GDSC>; + clock-names = "slave_iface"; + clocks = <&mmcc HDMI_S_AHB_CLK>; + core-vdda-supply = <&pm8921_hdmi_mvs>; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/mdp4.txt b/Documentation/devicetree/bindings/display/msm/mdp4.txt new file mode 100644 index 000000000..3c341a15c --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/mdp4.txt @@ -0,0 +1,112 @@ +Qualcomm adreno/snapdragon MDP4 display controller + +Description: + +This is the bindings documentation for the MDP4 display controller found in +SoCs like MSM8960, APQ8064 and MSM8660. + +Required properties: +- compatible: + * "qcom,mdp4" - mdp4 +- reg: Physical base address and length of the controller's registers. +- interrupts: The interrupt signal from the display controller. +- clocks: device clocks + See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. + * "core_clk" + * "iface_clk" + * "bus_clk" + * "lut_clk" + * "hdmi_clk" + * "tv_clk" +- ports: contains the list of output ports from MDP. These connect to interfaces + that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a + special case since it is a part of the MDP block itself). + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + The output port mappings are: + Port 0 -> LCDC/LVDS + Port 1 -> DSI1 Cmd/Video + Port 2 -> DSI2 Cmd/Video + Port 3 -> DTV + +Optional properties: +- clock-names: the following clocks are optional: + * "lut_clk" + +Example: + +/ { + ... + + hdmi: hdmi@4a00000 { + ... + ports { + ... + port@0 { + reg = <0>; + hdmi_in: endpoint { + remote-endpoint = <&mdp_dtv_out>; + }; + }; + ... + }; + ... + }; + + ... + + mdp: mdp@5100000 { + compatible = "qcom,mdp4"; + reg = <0x05100000 0xf0000>; + interrupts = <GIC_SPI 75 0>; + clock-names = + "core_clk", + "iface_clk", + "lut_clk", + "hdmi_clk", + "tv_clk"; + clocks = + <&mmcc MDP_CLK>, + <&mmcc MDP_AHB_CLK>, + <&mmcc MDP_AXI_CLK>, + <&mmcc MDP_LUT_CLK>, + <&mmcc HDMI_TV_CLK>, + <&mmcc MDP_TV_CLK>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp_lvds_out: endpoint { + }; + }; + + port@1 { + reg = <1>; + mdp_dsi1_out: endpoint { + }; + }; + + port@2 { + reg = <2>; + mdp_dsi2_out: endpoint { + }; + }; + + port@3 { + reg = <3>; + mdp_dtv_out: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/msm/mdp5.txt b/Documentation/devicetree/bindings/display/msm/mdp5.txt new file mode 100644 index 000000000..4e1133854 --- /dev/null +++ b/Documentation/devicetree/bindings/display/msm/mdp5.txt @@ -0,0 +1,158 @@ +Qualcomm adreno/snapdragon MDP5 display controller + +Description: + +This is the bindings documentation for the Mobile Display Subsytem(MDSS) that +encapsulates sub-blocks like MDP5, DSI, HDMI, eDP etc, and the MDP5 display +controller found in SoCs like MSM8974, APQ8084, MSM8916, MSM8994 and MSM8996. + +MDSS: +Required properties: +- compatible: + * "qcom,mdss" - MDSS +- reg: Physical base address and length of the controller's registers. +- reg-names: The names of register regions. The following regions are required: + * "mdss_phys" + * "vbif_phys" +- interrupts: The interrupt signal from MDSS. +- interrupt-controller: identifies the node as an interrupt controller. +- #interrupt-cells: specifies the number of cells needed to encode an interrupt + source, should be 1. +- power-domains: a power domain consumer specifier according to + Documentation/devicetree/bindings/power/power_domain.txt +- clocks: device clocks. See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. + * "iface" + * "bus" + * "vsync" +- #address-cells: number of address cells for the MDSS children. Should be 1. +- #size-cells: Should be 1. +- ranges: parent bus address space is the same as the child bus address space. + +Optional properties: +- clock-names: the following clocks are optional: + * "lut" + +MDP5: +Required properties: +- compatible: + * "qcom,mdp5" - MDP5 +- reg: Physical base address and length of the controller's registers. +- reg-names: The names of register regions. The following regions are required: + * "mdp_phys" +- interrupts: Interrupt line from MDP5 to MDSS interrupt controller. +- clocks: device clocks. See ../clocks/clock-bindings.txt for details. +- clock-names: the following clocks are required. +- * "bus" +- * "iface" +- * "core" +- * "vsync" +- ports: contains the list of output ports from MDP. These connect to interfaces + that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a + special case since it is a part of the MDP block itself). + + Each output port contains an endpoint that describes how it is connected to an + external interface. These are described by the standard properties documented + here: + Documentation/devicetree/bindings/graph.txt + Documentation/devicetree/bindings/media/video-interfaces.txt + + The availability of output ports can vary across SoC revisions: + + For MSM8974 and APQ8084: + Port 0 -> MDP_INTF0 (eDP) + Port 1 -> MDP_INTF1 (DSI1) + Port 2 -> MDP_INTF2 (DSI2) + Port 3 -> MDP_INTF3 (HDMI) + + For MSM8916: + Port 0 -> MDP_INTF1 (DSI1) + + For MSM8994 and MSM8996: + Port 0 -> MDP_INTF1 (DSI1) + Port 1 -> MDP_INTF2 (DSI2) + Port 2 -> MDP_INTF3 (HDMI) + +Optional properties: +- clock-names: the following clocks are optional: + * "lut" + +Example: + +/ { + ... + + mdss: mdss@1a00000 { + compatible = "qcom,mdss"; + reg = <0x1a00000 0x1000>, + <0x1ac8000 0x3000>; + reg-names = "mdss_phys", "vbif_phys"; + + power-domains = <&gcc MDSS_GDSC>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface", + "bus", + "vsync" + + interrupts = <0 72 0>; + + interrupt-controller; + #interrupt-cells = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mdp: mdp@1a01000 { + compatible = "qcom,mdp5"; + reg = <0x1a01000 0x90000>; + reg-names = "mdp_phys"; + + interrupt-parent = <&mdss>; + interrupts = <0 0>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_MDP_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface", + "bus", + "core", + "vsync"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + mdp5_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + }; + }; + + dsi0: dsi@1a98000 { + ... + ports { + ... + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&mdp5_intf1_out>; + }; + }; + ... + }; + ... + }; + + dsi_phy0: dsi-phy@1a98300 { + ... + }; + }; +}; |