1 files changed, 76 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/dma/sun6i-dma.txt b/Documentation/devicetree/bindings/dma/sun6i-dma.txt
new file mode 100644
index 000000000..7fccc20d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/dma/sun6i-dma.txt
@@ -0,0 +1,76 @@
+Allwinner A31 DMA Controller
+
+This driver follows the generic DMA bindings defined in dma.txt.
+
+Required properties:
+
+- compatible:	Must be one of
+		  "allwinner,sun6i-a31-dma"
+		  "allwinner,sun8i-a23-dma"
+		  "allwinner,sun8i-a83t-dma"
+		  "allwinner,sun8i-h3-dma"
+		  "allwinner,sun8i-v3s-dma"
+- reg:		Should contain the registers base address and length
+- interrupts:	Should contain a reference to the interrupt used by this device
+- clocks:	Should contain a reference to the parent AHB clock
+- resets:	Should contain a reference to the reset controller asserting
+		this device in reset
+- #dma-cells :	Should be 1, a single cell holding a line request number
+
+Example:
+	dma: dma-controller@1c02000 {
+		compatible = "allwinner,sun6i-a31-dma";
+		reg = <0x01c02000 0x1000>;
+		interrupts = <0 50 4>;
+		clocks = <&ahb1_gates 6>;
+		resets = <&ahb1_rst 6>;
+		#dma-cells = <1>;
+	};
+
+------------------------------------------------------------------------------
+For A64 DMA controller:
+
+Required properties:
+- compatible:	"allwinner,sun50i-a64-dma"
+- dma-channels: Number of DMA channels supported by the controller.
+		Refer to Documentation/devicetree/bindings/dma/dma.txt
+- all properties above, i.e. reg, interrupts, clocks, resets and #dma-cells
+
+Optional properties:
+- dma-requests: Number of DMA request signals supported by the controller.
+		Refer to Documentation/devicetree/bindings/dma/dma.txt
+
+Example:
+	dma: dma-controller@1c02000 {
+		compatible = "allwinner,sun50i-a64-dma";
+		reg = <0x01c02000 0x1000>;
+		interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&ccu CLK_BUS_DMA>;
+		dma-channels = <8>;
+		dma-requests = <27>;
+		resets = <&ccu RST_BUS_DMA>;
+		#dma-cells = <1>;
+	};
+------------------------------------------------------------------------------
+
+Clients:
+
+DMA clients connected to the A31 DMA controller must use the format
+described in the dma.txt file, using a two-cell specifier for each
+channel: a phandle plus one integer cells.
+The two cells in order are:
+
+1. A phandle pointing to the DMA controller.
+2. The port ID as specified in the datasheet
+
+Example:
+spi2: spi@1c6a000 {
+	compatible = "allwinner,sun6i-a31-spi";
+	reg = <0x01c6a000 0x1000>;
+	interrupts = <0 67 4>;
+	clocks = <&ahb1_gates 22>, <&spi2_clk>;
+	clock-names = "ahb", "mod";
+	dmas = <&dma 25>, <&dma 25>;
+	dma-names = "rx", "tx";
+	resets = <&ahb1_rst 22>;
+};