diff options
Diffstat (limited to '')
5 files changed, 109 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/pressure/bmp085.txt b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt new file mode 100644 index 000000000..61c72e63c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/bmp085.txt @@ -0,0 +1,27 @@ +BMP085/BMP18x/BMP28x digital pressure sensors + +Required properties: +- compatible: must be one of: + "bosch,bmp085" + "bosch,bmp180" + "bosch,bmp280" + "bosch,bme280" + +Optional properties: +- interrupts: interrupt mapping for IRQ +- reset-gpios: a GPIO line handling reset of the sensor: as the line is + active low, it should be marked GPIO_ACTIVE_LOW (see gpio/gpio.txt) +- vddd-supply: digital voltage regulator (see regulator/regulator.txt) +- vdda-supply: analog voltage regulator (see regulator/regulator.txt) + +Example: + +pressure@77 { + compatible = "bosch,bmp085"; + reg = <0x77>; + interrupt-parent = <&gpio0>; + interrupts = <25 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + vddd-supply = <&foo>; + vdda-supply = <&bar>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/hp03.txt b/Documentation/devicetree/bindings/iio/pressure/hp03.txt new file mode 100644 index 000000000..831dbee7a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/hp03.txt @@ -0,0 +1,17 @@ +HopeRF HP03 digital pressure/temperature sensors + +Required properties: +- compatible: must be "hoperf,hp03" +- xclr-gpio: must be device tree identifier of the XCLR pin. + The XCLR pin is a reset of the ADC in the chip, + it must be pulled HI before the conversion and + readout of the value from the ADC registers and + pulled LO afterward. + +Example: + +hp03@77 { + compatible = "hoperf,hp03"; + reg = <0x77>; + xclr-gpio = <&portc 0 0x0>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/ms5611.txt b/Documentation/devicetree/bindings/iio/pressure/ms5611.txt new file mode 100644 index 000000000..17bca866c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/ms5611.txt @@ -0,0 +1,19 @@ +MEAS ms5611 family pressure sensors + +Pressure sensors from MEAS Switzerland with SPI and I2C bus interfaces. + +Required properties: +- compatible: "meas,ms5611" or "meas,ms5607" +- reg: the I2C address or SPI chip select the device will respond to + +Optional properties: +- vdd-supply: an optional regulator that needs to be on to provide VDD + power to the sensor. + +Example: + +ms5607@77 { + compatible = "meas,ms5607"; + reg = <0x77>; + vdd-supply = <&ldo_3v3_gnss>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/ms5637.txt b/Documentation/devicetree/bindings/iio/pressure/ms5637.txt new file mode 100644 index 000000000..1f43ffa06 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/ms5637.txt @@ -0,0 +1,17 @@ +* MS5637 - Measurement-Specialties MS5637, MS5805, MS5837 and MS8607 pressure & temperature sensor + +Required properties: + + -compatible: should be one of the following + meas,ms5637 + meas,ms5805 + meas,ms5837 + meas,ms8607-temppressure + -reg: I2C address of the sensor + +Example: + +ms5637@76 { + compatible = "meas,ms5637"; + reg = <0x76>; +}; diff --git a/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt b/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt new file mode 100644 index 000000000..a36ab3e0c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/zpa2326.txt @@ -0,0 +1,29 @@ +Murata ZPA2326 pressure sensor + +Pressure sensor from Murata with SPI and I2C bus interfaces. + +Required properties: +- compatible: "murata,zpa2326" +- reg: the I2C address or SPI chip select the device will respond to + +Recommended properties for SPI bus usage: +- spi-max-frequency: maximum SPI bus frequency as documented in + Documentation/devicetree/bindings/spi/spi-bus.txt + +Optional properties: +- vref-supply: an optional regulator that needs to be on to provide VREF + power to the sensor +- vdd-supply: an optional regulator that needs to be on to provide VDD + power to the sensor +- interrupts: interrupt mapping for IRQ as documented in + Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + +Example: + +zpa2326@5c { + compatible = "murata,zpa2326"; + reg = <0x5c>; + interrupt-parent = <&gpio>; + interrupts = <12>; + vdd-supply = <&ldo_1v8_gnss>; +}; |