1 files changed, 171 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt
new file mode 100644
index 000000000..2f3244648
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt
@@ -0,0 +1,171 @@
+* ARM Generic Interrupt Controller
+
+ARM SMP cores are often associated with a GIC, providing per processor
+interrupts (PPI), shared processor interrupts (SPI) and software
+generated interrupts (SGI).
+
+Primary GIC is attached directly to the CPU and typically has PPIs and SGIs.
+Secondary GICs are cascaded into the upward interrupt controller and do not
+have PPIs or SGIs.
+
+Main node required properties:
+
+- compatible : should be one of:
+	"arm,arm1176jzf-devchip-gic"
+	"arm,arm11mp-gic"
+	"arm,cortex-a15-gic"
+	"arm,cortex-a7-gic"
+	"arm,cortex-a9-gic"
+	"arm,eb11mp-gic"
+	"arm,gic-400"
+	"arm,pl390"
+	"arm,tc11mp-gic"
+	"brcm,brahma-b15-gic"
+	"nvidia,tegra210-agic"
+	"qcom,msm-8660-qgic"
+	"qcom,msm-qgic2"
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source.  The type shall be a <u32> and the value shall be 3.
+
+  The 1st cell is the interrupt type; 0 for SPI interrupts, 1 for PPI
+  interrupts.
+
+  The 2nd cell contains the interrupt number for the interrupt type.
+  SPI interrupts are in the range [0-987].  PPI interrupts are in the
+  range [0-15].
+
+  The 3rd cell is the flags, encoded as follows:
+	bits[3:0] trigger type and level flags.
+		1 = low-to-high edge triggered
+		2 = high-to-low edge triggered (invalid for SPIs)
+		4 = active high level-sensitive
+		8 = active low level-sensitive (invalid for SPIs).
+	bits[15:8] PPI interrupt cpu mask.  Each bit corresponds to each of
+	the 8 possible cpus attached to the GIC.  A bit set to '1' indicated
+	the interrupt is wired to that CPU.  Only valid for PPI interrupts.
+	Also note that the configurability of PPI interrupts is IMPLEMENTATION
+	DEFINED and as such not guaranteed to be present (most SoC available
+	in 2014 seem to ignore the setting of this flag and use the hardware
+	default value).
+
+- reg : Specifies base physical address(s) and size of the GIC registers. The
+  first region is the GIC distributor register base and size. The 2nd region is
+  the GIC cpu interface register base and size.
+
+Optional
+- interrupts	: Interrupt source of the parent interrupt controller on
+  secondary GICs, or VGIC maintenance interrupt on primary GIC (see
+  below).
+
+- cpu-offset	: per-cpu offset within the distributor and cpu interface
+  regions, used when the GIC doesn't have banked registers. The offset is
+  cpu-offset * cpu-nr.
+
+- clocks        : List of phandle and clock-specific pairs, one for each entry
+  in clock-names.
+- clock-names   : List of names for the GIC clock input(s). Valid clock names
+  depend on the GIC variant:
+	"ic_clk" (for "arm,arm11mp-gic")
+	"PERIPHCLKEN" (for "arm,cortex-a15-gic")
+	"PERIPHCLK", "PERIPHCLKEN" (for "arm,cortex-a9-gic")
+	"clk" (for "arm,gic-400" and "nvidia,tegra210")
+	"gclk" (for "arm,pl390")
+
+- power-domains : A phandle and PM domain specifier as defined by bindings of
+		  the power controller specified by phandle, used when the GIC
+		  is part of a Power or Clock Domain.
+
+
+Example:
+
+	intc: interrupt-controller@fff11000 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		interrupt-controller;
+		reg = <0xfff11000 0x1000>,
+		      <0xfff10100 0x100>;
+	};
+
+
+* GIC virtualization extensions (VGIC)
+
+For ARM cores that support the virtualization extensions, additional
+properties must be described (they only exist if the GIC is the
+primary interrupt controller).
+
+Required properties:
+
+- reg : Additional regions specifying the base physical address and
+  size of the VGIC registers. The first additional region is the GIC
+  virtual interface control register base and size. The 2nd additional
+  region is the GIC virtual cpu interface register base and size.
+
+- interrupts : VGIC maintenance interrupt.
+
+Example:
+
+	interrupt-controller@2c001000 {
+		compatible = "arm,cortex-a15-gic";
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x2c001000 0x1000>,
+		      <0x2c002000 0x2000>,
+		      <0x2c004000 0x2000>,
+		      <0x2c006000 0x2000>;
+		interrupts = <1 9 0xf04>;
+	};
+
+
+* GICv2m extension for MSI/MSI-x support (Optional)
+
+Certain revisions of GIC-400 supports MSI/MSI-x via V2M register frame(s).
+This is enabled by specifying v2m sub-node(s).
+
+Required properties:
+
+- compatible	    : The value here should contain "arm,gic-v2m-frame".
+
+- msi-controller    : Identifies the node as an MSI controller.
+
+- reg		    : GICv2m MSI interface register base and size
+
+Optional properties:
+
+- arm,msi-base-spi  : When the MSI_TYPER register contains an incorrect
+  		      value, this property should contain the SPI base of
+		      the MSI frame, overriding the HW value.
+
+- arm,msi-num-spis  : When the MSI_TYPER register contains an incorrect
+  		      value, this property should contain the number of
+		      SPIs assigned to the frame, overriding the HW value.
+
+Example:
+
+	interrupt-controller@e1101000 {
+		compatible = "arm,gic-400";
+		#interrupt-cells = <3>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		interrupt-controller;
+		interrupts = <1 8 0xf04>;
+		ranges = <0 0 0 0xe1100000 0 0x100000>;
+		reg = <0x0 0xe1110000 0 0x01000>,
+		      <0x0 0xe112f000 0 0x02000>,
+		      <0x0 0xe1140000 0 0x10000>,
+		      <0x0 0xe1160000 0 0x10000>;
+		v2m0: v2m@8000 {
+			compatible = "arm,gic-v2m-frame";
+			msi-controller;
+			reg = <0x0 0x80000 0 0x1000>;
+		};
+
+		....
+
+		v2mN: v2m@9000 {
+			compatible = "arm,gic-v2m-frame";
+			msi-controller;
+			reg = <0x0 0x90000 0 0x1000>;
+		};
+	};