diff options
Diffstat (limited to '')
22 files changed, 986 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mips/ath79-soc.txt b/Documentation/devicetree/bindings/mips/ath79-soc.txt new file mode 100644 index 000000000..88a12a43e --- /dev/null +++ b/Documentation/devicetree/bindings/mips/ath79-soc.txt @@ -0,0 +1,21 @@ +Binding for Qualcomm Atheros AR7xxx/AR9XXX SoC + +Each device tree must specify a compatible value for the AR SoC +it uses in the compatible property of the root node. The compatible +value must be one of the following values: + +- qca,ar7130 +- qca,ar7141 +- qca,ar7161 +- qca,ar7240 +- qca,ar7241 +- qca,ar7242 +- qca,ar9130 +- qca,ar9132 +- qca,ar9330 +- qca,ar9331 +- qca,ar9341 +- qca,ar9342 +- qca,ar9344 +- qca,qca9556 +- qca,qca9558 diff --git a/Documentation/devicetree/bindings/mips/brcm/brcm,bmips.txt b/Documentation/devicetree/bindings/mips/brcm/brcm,bmips.txt new file mode 100644 index 000000000..8ef71b408 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/brcm/brcm,bmips.txt @@ -0,0 +1,8 @@ +* Broadcom MIPS (BMIPS) CPUs + +Required properties: +- compatible: "brcm,bmips3300", "brcm,bmips4350", "brcm,bmips4380", + "brcm,bmips5000" + +- mips-hpt-frequency: This is common to all CPUs in the system so it lives + under the "cpus" node. diff --git a/Documentation/devicetree/bindings/mips/brcm/soc.txt b/Documentation/devicetree/bindings/mips/brcm/soc.txt new file mode 100644 index 000000000..3a66d3c48 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/brcm/soc.txt @@ -0,0 +1,166 @@ +* Broadcom cable/DSL/settop platforms + +Required properties: + +- compatible: "brcm,bcm3368", "brcm,bcm3384", "brcm,bcm33843" + "brcm,bcm3384-viper", "brcm,bcm33843-viper" + "brcm,bcm6328", "brcm,bcm6358", "brcm,bcm6362", "brcm,bcm6368", + "brcm,bcm63168", "brcm,bcm63268", + "brcm,bcm7125", "brcm,bcm7346", "brcm,bcm7358", "brcm,bcm7360", + "brcm,bcm7362", "brcm,bcm7420", "brcm,bcm7425" + +The experimental -viper variants are for running Linux on the 3384's +BMIPS4355 cable modem CPU instead of the BMIPS5000 application processor. + +Power management +---------------- + +For power management (particularly, S2/S3/S5 system suspend), the following SoC +components are needed: + += Always-On control block (AON CTRL) + +This hardware provides control registers for the "always-on" (even in low-power +modes) hardware, such as the Power Management State Machine (PMSM). + +Required properties: +- compatible : should be one of + "brcm,bcm7425-aon-ctrl" + "brcm,bcm7429-aon-ctrl" + "brcm,bcm7435-aon-ctrl" and + "brcm,brcmstb-aon-ctrl" +- reg : the register start and length for the AON CTRL block + +Example: + +syscon@410000 { + compatible = "brcm,bcm7425-aon-ctrl", "brcm,brcmstb-aon-ctrl"; + reg = <0x410000 0x400>; +}; + += Memory controllers + +A Broadcom STB SoC typically has a number of independent memory controllers, +each of which may have several associated hardware blocks, which are versioned +independently (control registers, DDR PHYs, etc.). One might consider +describing these controllers as a parent "memory controllers" block, which +contains N sub-nodes (one for each controller in the system), each of which is +associated with a number of hardware register resources (e.g., its PHY. + +== MEMC (MEMory Controller) + +Represents a single memory controller instance. + +Required properties: +- compatible : should contain "brcm,brcmstb-memc" and "simple-bus" +- ranges : should contain the child address in the parent address + space, must be 0 here, and the register start and length of + the entire memory controller (including all sub nodes: DDR PHY, + arbiter, etc.) +- #address-cells : must be 1 +- #size-cells : must be 1 + +Example: + + memory-controller@0 { + compatible = "brcm,brcmstb-memc", "simple-bus"; + ranges = <0x0 0x0 0xa000>; + #address-cells = <1>; + #size-cells = <1>; + + memc-arb@1000 { + ... + }; + + memc-ddr@2000 { + ... + }; + + ddr-phy@6000 { + ... + }; + }; + +Should contain subnodes for any of the following relevant hardware resources: + +== DDR PHY control + +Control registers for this memory controller's DDR PHY. + +Required properties: +- compatible : should contain one of these + "brcm,brcmstb-ddr-phy-v64.5" + "brcm,brcmstb-ddr-phy" + +- reg : the DDR PHY register range and length + +Example: + + ddr-phy@6000 { + compatible = "brcm,brcmstb-ddr-phy-v64.5"; + reg = <0x6000 0xc8>; + }; + +== DDR memory controller sequencer + +Control registers for this memory controller's DDR memory sequencer + +Required properties: +- compatible : should contain one of these + "brcm,bcm7425-memc-ddr" + "brcm,bcm7429-memc-ddr" + "brcm,bcm7435-memc-ddr" and + "brcm,brcmstb-memc-ddr" + +- reg : the DDR sequencer register range and length + +Example: + + memc-ddr@2000 { + compatible = "brcm,bcm7425-memc-ddr", "brcm,brcmstb-memc-ddr"; + reg = <0x2000 0x300>; + }; + +== MEMC Arbiter + +The memory controller arbiter is responsible for memory clients allocation +(bandwidth, priorities etc.) and needs to have its contents restored during +deep sleep states (S3). + +Required properties: + +- compatible : should contain one of these + "brcm,brcmstb-memc-arb-v10.0.0.0" + "brcm,brcmstb-memc-arb" + +- reg : the DDR Arbiter register range and length + +Example: + + memc-arb@1000 { + compatible = "brcm,brcmstb-memc-arb-v10.0.0.0"; + reg = <0x1000 0x248>; + }; + +== Timers + +The Broadcom STB chips contain a timer block with several general purpose +timers that can be used. + +Required properties: + +- compatible : should contain one of: + "brcm,bcm7425-timers" + "brcm,bcm7429-timers" + "brcm,bcm7435-timers" and + "brcm,brcmstb-timers" +- reg : the timers register range +- interrupts : the interrupt line for this timer block + +Example: + + timers: timer@4067c0 { + compatible = "brcm,bcm7425-timers", "brcm,brcmstb-timers"; + reg = <0x4067c0 0x40>; + interrupts = <&periph_intc 19>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/bootbus.txt b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt new file mode 100644 index 000000000..658147822 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/bootbus.txt @@ -0,0 +1,126 @@ +* Boot Bus + +The Octeon Boot Bus is a configurable parallel bus with 8 chip +selects. Each chip select is independently configurable. + +Properties: +- compatible: "cavium,octeon-3860-bootbus" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the Boot Bus' register bank. + +- #address-cells: Must be <2>. The first cell is the chip select + within the bootbus. The second cell is the offset from the chip select. + +- #size-cells: Must be <1>. + +- ranges: There must be one one triplet of (child-bus-address, + parent-bus-address, length) for each active chip select. If the + length element for any triplet is zero, the chip select is disabled, + making it inactive. + +The configuration parameters for each chip select are stored in child +nodes. + +Configuration Properties: +- compatible: "cavium,octeon-3860-bootbus-config" + +- cavium,cs-index: A single cell indicating the chip select that + corresponds to this configuration. + +- cavium,t-adr: A cell specifying the ADR timing (in nS). + +- cavium,t-ce: A cell specifying the CE timing (in nS). + +- cavium,t-oe: A cell specifying the OE timing (in nS). + +- cavium,t-we: A cell specifying the WE timing (in nS). + +- cavium,t-rd-hld: A cell specifying the RD_HLD timing (in nS). + +- cavium,t-wr-hld: A cell specifying the WR_HLD timing (in nS). + +- cavium,t-pause: A cell specifying the PAUSE timing (in nS). + +- cavium,t-wait: A cell specifying the WAIT timing (in nS). + +- cavium,t-page: A cell specifying the PAGE timing (in nS). + +- cavium,t-rd-dly: A cell specifying the RD_DLY timing (in nS). + +- cavium,pages: A cell specifying the PAGES parameter (0 = 8 bytes, 1 + = 2 bytes, 2 = 4 bytes, 3 = 8 bytes). + +- cavium,wait-mode: Optional. If present, wait mode (WAITM) is selected. + +- cavium,page-mode: Optional. If present, page mode (PAGEM) is selected. + +- cavium,bus-width: A cell specifying the WIDTH parameter (in bits) of + the bus for this chip select. + +- cavium,ale-mode: Optional. If present, ALE mode is selected. + +- cavium,sam-mode: Optional. If present, SAM mode is selected. + +- cavium,or-mode: Optional. If present, OR mode is selected. + +Example: + bootbus: bootbus@1180000000000 { + compatible = "cavium,octeon-3860-bootbus"; + reg = <0x11800 0x00000000 0x0 0x200>; + /* The chip select number and offset */ + #address-cells = <2>; + /* The size of the chip select region */ + #size-cells = <1>; + ranges = <0 0 0x0 0x1f400000 0xc00000>, + <1 0 0x10000 0x30000000 0>, + <2 0 0x10000 0x40000000 0>, + <3 0 0x10000 0x50000000 0>, + <4 0 0x0 0x1d020000 0x10000>, + <5 0 0x0 0x1d040000 0x10000>, + <6 0 0x0 0x1d050000 0x10000>, + <7 0 0x10000 0x90000000 0>; + + cavium,cs-config@0 { + compatible = "cavium,octeon-3860-bootbus-config"; + cavium,cs-index = <0>; + cavium,t-adr = <20>; + cavium,t-ce = <60>; + cavium,t-oe = <60>; + cavium,t-we = <45>; + cavium,t-rd-hld = <35>; + cavium,t-wr-hld = <45>; + cavium,t-pause = <0>; + cavium,t-wait = <0>; + cavium,t-page = <35>; + cavium,t-rd-dly = <0>; + + cavium,pages = <0>; + cavium,bus-width = <8>; + }; + . + . + . + cavium,cs-config@6 { + compatible = "cavium,octeon-3860-bootbus-config"; + cavium,cs-index = <6>; + cavium,t-adr = <5>; + cavium,t-ce = <300>; + cavium,t-oe = <270>; + cavium,t-we = <150>; + cavium,t-rd-hld = <100>; + cavium,t-wr-hld = <70>; + cavium,t-pause = <0>; + cavium,t-wait = <0>; + cavium,t-page = <320>; + cavium,t-rd-dly = <0>; + + cavium,pages = <0>; + cavium,wait-mode; + cavium,bus-width = <16>; + }; + . + . + . + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/cib.txt b/Documentation/devicetree/bindings/mips/cavium/cib.txt new file mode 100644 index 000000000..410efa322 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/cib.txt @@ -0,0 +1,41 @@ +* Cavium Interrupt Bus widget + +Properties: +- compatible: "cavium,octeon-7130-cib" + + Compatibility with cn70XX SoCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: Two elements consisting of the addresses of the RAW and EN + registers of the CIB block + +- cavium,max-bits: The index (zero based) of the highest numbered bit + in the CIB block. + +- interrupts: The CIU line to which the CIB block is connected. + +- #interrupt-cells: Must be <2>. The first cell is the bit within the + CIB. The second cell specifies the triggering semantics of the + line. + +Example: + + interrupt-controller@107000000e000 { + compatible = "cavium,octeon-7130-cib"; + reg = <0x10700 0x0000e000 0x0 0x8>, /* RAW */ + <0x10700 0x0000e100 0x0 0x8>; /* EN */ + cavium,max-bits = <23>; + + interrupt-controller; + interrupt-parent = <&ciu>; + interrupts = <1 24>; + /* Interrupts are specified by two parts: + * 1) Bit number in the CIB* registers + * 2) Triggering (1 - edge rising + * 2 - edge falling + * 4 - level active high + * 8 - level active low) + */ + #interrupt-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu.txt b/Documentation/devicetree/bindings/mips/cavium/ciu.txt new file mode 100644 index 000000000..2c2d0746b --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/ciu.txt @@ -0,0 +1,26 @@ +* Central Interrupt Unit + +Properties: +- compatible: "cavium,octeon-3860-ciu" + + Compatibility with all cn3XXX, cn5XXX and cn63XX SOCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: The base address of the CIU's register bank. + +- #interrupt-cells: Must be <2>. The first cell is the bank within + the CIU and may have a value of 0 or 1. The second cell is the bit + within the bank and may have a value between 0 and 63. + +Example: + interrupt-controller@1070000000000 { + compatible = "cavium,octeon-3860-ciu"; + interrupt-controller; + /* Interrupts are specified by two parts: + * 1) Controller register (0 or 1) + * 2) Bit within the register (0..63) + */ + #interrupt-cells = <2>; + reg = <0x10700 0x00000000 0x0 0x7000>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu2.txt b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt new file mode 100644 index 000000000..0ec7ba8bb --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/ciu2.txt @@ -0,0 +1,27 @@ +* Central Interrupt Unit + +Properties: +- compatible: "cavium,octeon-6880-ciu2" + + Compatibility with 68XX SOCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: The base address of the CIU's register bank. + +- #interrupt-cells: Must be <2>. The first cell is the bank within + the CIU and may have a value between 0 and 63. The second cell is + the bit within the bank and may also have a value between 0 and 63. + +Example: + interrupt-controller@1070100000000 { + compatible = "cavium,octeon-6880-ciu2"; + interrupt-controller; + /* Interrupts are specified by two parts: + * 1) Controller register (0..63) + * 2) Bit within the register (0..63) + */ + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x10701 0x00000000 0x0 0x4000000>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/ciu3.txt b/Documentation/devicetree/bindings/mips/cavium/ciu3.txt new file mode 100644 index 000000000..616862ad2 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/ciu3.txt @@ -0,0 +1,27 @@ +* Central Interrupt Unit v3 + +Properties: +- compatible: "cavium,octeon-7890-ciu3" + + Compatibility with 78XX and 73XX SOCs. + +- interrupt-controller: This is an interrupt controller. + +- reg: The base address of the CIU's register bank. + +- #interrupt-cells: Must be <2>. The first cell is source number. + The second cell indicates the triggering semantics, and may have a + value of either 4 for level semantics, or 1 for edge semantics. + +Example: + interrupt-controller@1010000000000 { + compatible = "cavium,octeon-7890-ciu3"; + interrupt-controller; + /* Interrupts are specified by two parts: + * 1) Source number (20 significant bits) + * 2) Trigger type: (4 == level, 1 == edge) + */ + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x10100 0x00000000 0x0 0xb0000000>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt new file mode 100644 index 000000000..a5bdff400 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/dma-engine.txt @@ -0,0 +1,21 @@ +* DMA Engine. + +The Octeon DMA Engine transfers between the Boot Bus and main memory. +The DMA Engine will be referred to by phandle by any device that is +connected to it. + +Properties: +- compatible: "cavium,octeon-5750-bootbus-dma" + + Compatibility with all cn52XX, cn56XX and cn6XXX SOCs. + +- reg: The base address of the DMA Engine's register bank. + +- interrupts: A single interrupt specifier. + +Example: + dma0: dma-engine@1180000000100 { + compatible = "cavium,octeon-5750-bootbus-dma"; + reg = <0x11800 0x00000100 0x0 0x8>; + interrupts = <0 63>; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/sata-uctl.txt b/Documentation/devicetree/bindings/mips/cavium/sata-uctl.txt new file mode 100644 index 000000000..3bd3c2f0b --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/sata-uctl.txt @@ -0,0 +1,42 @@ +* UCTL SATA controller glue + +UCTL is the bridge unit between the I/O interconnect (an internal bus) +and the SATA AHCI host controller (UAHC). It performs the following functions: + - provides interfaces for the applications to access the UAHC AHCI + registers on the CN71XX I/O space. + - provides a bridge for UAHC to fetch AHCI command table entries and data + buffers from Level 2 Cache. + - posts interrupts to the CIU. + - contains registers that: + - control the behavior of the UAHC + - control the clock/reset generation to UAHC + - control endian swapping for all UAHC registers and DMA accesses + +Properties: + +- compatible: "cavium,octeon-7130-sata-uctl" + + Compatibility with the cn7130 SOC. + +- reg: The base address of the UCTL register bank. + +- #address-cells, #size-cells, ranges and dma-ranges must be present and hold + suitable values to map all child nodes. + +Example: + + uctl@118006c000000 { + compatible = "cavium,octeon-7130-sata-uctl"; + reg = <0x11800 0x6c000000 0x0 0x100>; + ranges; /* Direct mapping */ + dma-ranges; + #address-cells = <2>; + #size-cells = <2>; + + sata: sata@16c0000000000 { + compatible = "cavium,octeon-7130-ahci"; + reg = <0x16c00 0x00000000 0x0 0x200>; + interrupt-parent = <&cibsata>; + interrupts = <2 4>; /* Bit: 2, level */ + }; + }; diff --git a/Documentation/devicetree/bindings/mips/cavium/uctl.txt b/Documentation/devicetree/bindings/mips/cavium/uctl.txt new file mode 100644 index 000000000..aa66b9b8d --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cavium/uctl.txt @@ -0,0 +1,46 @@ +* UCTL USB controller glue + +Properties: +- compatible: "cavium,octeon-6335-uctl" + + Compatibility with all cn6XXX SOCs. + +- reg: The base address of the UCTL register bank. + +- #address-cells: Must be <2>. + +- #size-cells: Must be <2>. + +- ranges: Empty to signify direct mapping of the children. + +- refclk-frequency: A single cell containing the reference clock + frequency in Hz. + +- refclk-type: A string describing the reference clock connection + either "crystal" or "external". + +Example: + uctl@118006f000000 { + compatible = "cavium,octeon-6335-uctl"; + reg = <0x11800 0x6f000000 0x0 0x100>; + ranges; /* Direct mapping */ + #address-cells = <2>; + #size-cells = <2>; + /* 12MHz, 24MHz and 48MHz allowed */ + refclk-frequency = <24000000>; + /* Either "crystal" or "external" */ + refclk-type = "crystal"; + + ehci@16f0000000000 { + compatible = "cavium,octeon-6335-ehci","usb-ehci"; + reg = <0x16f00 0x00000000 0x0 0x100>; + interrupts = <0 56>; + big-endian-regs; + }; + ohci@16f0000000400 { + compatible = "cavium,octeon-6335-ohci","usb-ohci"; + reg = <0x16f00 0x00000400 0x0 0x100>; + interrupts = <0 56>; + big-endian-regs; + }; + }; diff --git a/Documentation/devicetree/bindings/mips/cpu_irq.txt b/Documentation/devicetree/bindings/mips/cpu_irq.txt new file mode 100644 index 000000000..f080f06da --- /dev/null +++ b/Documentation/devicetree/bindings/mips/cpu_irq.txt @@ -0,0 +1,47 @@ +MIPS CPU interrupt controller + +On MIPS the mips_cpu_irq_of_init() helper can be used to initialize the 8 CPU +IRQs from a devicetree file and create a irq_domain for IRQ controller. + +With the irq_domain in place we can describe how the 8 IRQs are wired to the +platforms internal interrupt controller cascade. + +Below is an example of a platform describing the cascade inside the devicetree +and the code used to load it inside arch_init_irq(). + +Required properties: +- compatible : Should be "mti,cpu-interrupt-controller" + +Example devicetree: + cpu-irq: cpu-irq { + #address-cells = <0>; + + interrupt-controller; + #interrupt-cells = <1>; + + compatible = "mti,cpu-interrupt-controller"; + }; + + intc: intc@200 { + compatible = "ralink,rt2880-intc"; + reg = <0x200 0x100>; + + interrupt-controller; + #interrupt-cells = <1>; + + interrupt-parent = <&cpu-irq>; + interrupts = <2>; + }; + + +Example platform irq.c: +static struct of_device_id __initdata of_irq_ids[] = { + { .compatible = "mti,cpu-interrupt-controller", .data = mips_cpu_irq_of_init }, + { .compatible = "ralink,rt2880-intc", .data = intc_of_init }, + {}, +}; + +void __init arch_init_irq(void) +{ + of_irq_init(of_irq_ids); +} diff --git a/Documentation/devicetree/bindings/mips/img/pistachio-marduk.txt b/Documentation/devicetree/bindings/mips/img/pistachio-marduk.txt new file mode 100644 index 000000000..2d5126d52 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/img/pistachio-marduk.txt @@ -0,0 +1,10 @@ +Imagination Technologies' Pistachio SoC based Marduk Board +========================================================== + +Compatible string must be "img,pistachio-marduk", "img,pistachio" + +Hardware and other related documentation is available at +https://docs.creatordev.io/ci40/ + +It is also known as Creator Ci40. Marduk is legacy name and will +be there for decades. diff --git a/Documentation/devicetree/bindings/mips/img/pistachio.txt b/Documentation/devicetree/bindings/mips/img/pistachio.txt new file mode 100644 index 000000000..a736d889c --- /dev/null +++ b/Documentation/devicetree/bindings/mips/img/pistachio.txt @@ -0,0 +1,42 @@ +Imagination Pistachio SoC +========================= + +Required properties: +-------------------- + - compatible: Must include "img,pistachio". + +CPU nodes: +---------- +A "cpus" node is required. Required properties: + - #address-cells: Must be 1. + - #size-cells: Must be 0. +A CPU sub-node is also required for at least CPU 0. Since the topology may +be probed via CPS, it is not necessary to specify secondary CPUs. Required +propertis: + - device_type: Must be "cpu". + - compatible: Must be "mti,interaptiv". + - reg: CPU number. + - clocks: Must include the CPU clock. See ../../clock/clock-bindings.txt for + details on clock bindings. +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "mti,interaptiv"; + reg = <0>; + clocks = <&clk_core CLK_MIPS>; + }; + }; + + +Boot protocol: +-------------- +In accordance with the MIPS UHI specification[1], the bootloader must pass the +following arguments to the kernel: + - $a0: -2. + - $a1: KSEG0 address of the flattened device-tree blob. + +[1] http://prplfoundation.org/wiki/MIPS_documentation diff --git a/Documentation/devicetree/bindings/mips/img/xilfpga.txt b/Documentation/devicetree/bindings/mips/img/xilfpga.txt new file mode 100644 index 000000000..57e7ee942 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/img/xilfpga.txt @@ -0,0 +1,83 @@ +Imagination University Program MIPSfpga +======================================= + +Under the Imagination University Program, a microAptiv UP core has been +released for academic usage. + +As we are dealing with a MIPS core instantiated on an FPGA, specifications +are fluid and can be varied in RTL. + +This binding document is provided as baseline guidance for the example +project provided by IMG. + +The example project runs on the Nexys4DDR board by Digilent powered by +the ARTIX-7 FPGA by Xilinx. + +Relevant details about the example project and the Nexys4DDR board: + +- microAptiv UP core m14Kc +- 50MHz clock speed +- 128Mbyte DDR RAM at 0x0000_0000 +- 8Kbyte RAM at 0x1000_0000 +- axi_intc at 0x1020_0000 +- axi_uart16550 at 0x1040_0000 +- axi_gpio at 0x1060_0000 +- axi_i2c at 0x10A0_0000 +- custom_gpio at 0x10C0_0000 +- axi_ethernetlite at 0x10E0_0000 +- 8Kbyte BootRAM at 0x1FC0_0000 + +Required properties: +-------------------- + - compatible: Must include "digilent,nexys4ddr","img,xilfpga". + +CPU nodes: +---------- +A "cpus" node is required. Required properties: + - #address-cells: Must be 1. + - #size-cells: Must be 0. +A CPU sub-node is also required for at least CPU 0. Required properties: + - device_type: Must be "cpu". + - compatible: Must be "mips,m14Kc". + - reg: Must be <0>. + - clocks: phandle to ext clock for fixed-clock received by MIPS core. + +Example: + + compatible = "img,xilfpga","digilent,nexys4ddr"; + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "mips,m14Kc"; + reg = <0>; + clocks = <&ext>; + }; + }; + + ext: ext { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + +Boot protocol: +-------------- + +The BootRAM is a writeable "RAM" in FPGA at 0x1FC0_0000. +This is for easy reprogrammibility via JTAG. + +The BootRAM initializes the cache and the axi_uart peripheral. + +DDR initialization is already handled by a HW IP block. + +When the example project bitstream is loaded, the cpu_reset button +needs to be pressed. + +The bootram initializes the cache and axi_uart. +Then outputs MIPSFPGA\n\r on the serial port on the Nexys4DDR board. + +At this point, the board is ready to load the Linux kernel +vmlinux file via JTAG. diff --git a/Documentation/devicetree/bindings/mips/lantiq/fpi-bus.txt b/Documentation/devicetree/bindings/mips/lantiq/fpi-bus.txt new file mode 100644 index 000000000..0a2df4338 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/lantiq/fpi-bus.txt @@ -0,0 +1,31 @@ +Lantiq XWAY SoC FPI BUS binding +============================ + + +------------------------------------------------------------------------------- +Required properties: +- compatible : Should be one of + "lantiq,xrx200-fpi" +- reg : The address and length of the XBAR + configuration register. + Address and length of the FPI bus itself. +- lantiq,rcu : A phandle to the RCU syscon +- lantiq,offset-endianness : Offset of the endianness configuration + register + +------------------------------------------------------------------------------- +Example for the FPI on the xrx200 SoCs: + fpi@10000000 { + compatible = "lantiq,xrx200-fpi"; + ranges = <0x0 0x10000000 0xf000000>; + reg = <0x1f400000 0x1000>, + <0x10000000 0xf000000>; + lantiq,rcu = <&rcu0>; + lantiq,offset-endianness = <0x4c>; + #address-cells = <1>; + #size-cells = <1>; + + gptu@e100a00 { + ...... + }; + }; diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt new file mode 100644 index 000000000..a0c19bd1c --- /dev/null +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu-gphy.txt @@ -0,0 +1,36 @@ +Lantiq XWAY SoC GPHY binding +============================ + +This binding describes a software-defined ethernet PHY, provided by the RCU +module on newer Lantiq XWAY SoCs (xRX200 and newer). + +------------------------------------------------------------------------------- +Required properties: +- compatible : Should be one of + "lantiq,xrx200a1x-gphy" + "lantiq,xrx200a2x-gphy" + "lantiq,xrx300-gphy" + "lantiq,xrx330-gphy" +- reg : Addrress of the GPHY FW load address register +- resets : Must reference the RCU GPHY reset bit +- reset-names : One entry, value must be "gphy" or optional "gphy2" +- clocks : A reference to the (PMU) GPHY clock gate + +Optional properties: +- lantiq,gphy-mode : GPHY_MODE_GE (default) or GPHY_MODE_FE as defined in + <dt-bindings/mips/lantiq_xway_gphy.h> + + +------------------------------------------------------------------------------- +Example for the GPHys on the xRX200 SoCs: + +#include <dt-bindings/mips/lantiq_rcu_gphy.h> + gphy0: gphy@20 { + compatible = "lantiq,xrx200a2x-gphy"; + reg = <0x20 0x4>; + + resets = <&reset0 31 30>, <&reset1 7 7>; + reset-names = "gphy", "gphy2"; + clocks = <&pmu0 XRX200_PMU_GATE_GPHY>; + lantiq,gphy-mode = <GPHY_MODE_GE>; + }; diff --git a/Documentation/devicetree/bindings/mips/lantiq/rcu.txt b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt new file mode 100644 index 000000000..7f0822b4b --- /dev/null +++ b/Documentation/devicetree/bindings/mips/lantiq/rcu.txt @@ -0,0 +1,87 @@ +Lantiq XWAY SoC RCU binding +=========================== + +This binding describes the RCU (reset controller unit) multifunction device, +where each sub-device has it's own set of registers. + +The RCU register range is used for multiple purposes. Mostly one device +uses one or multiple register exclusively, but for some registers some +bits are for one driver and some other bits are for a different driver. +With this patch all accesses to the RCU registers will go through +syscon. + + +------------------------------------------------------------------------------- +Required properties: +- compatible : The first and second values must be: + "lantiq,xrx200-rcu", "simple-mfd", "syscon" +- reg : The address and length of the system control registers + + +------------------------------------------------------------------------------- +Example of the RCU bindings on a xRX200 SoC: + rcu0: rcu@203000 { + compatible = "lantiq,xrx200-rcu", "simple-mfd", "syscon"; + reg = <0x203000 0x100>; + ranges = <0x0 0x203000 0x100>; + big-endian; + + gphy0: gphy@20 { + compatible = "lantiq,xrx200a2x-gphy"; + reg = <0x20 0x4>; + + resets = <&reset0 31 30>, <&reset1 7 7>; + reset-names = "gphy", "gphy2"; + lantiq,gphy-mode = <GPHY_MODE_GE>; + }; + + gphy1: gphy@68 { + compatible = "lantiq,xrx200a2x-gphy"; + reg = <0x68 0x4>; + + resets = <&reset0 29 28>, <&reset1 6 6>; + reset-names = "gphy", "gphy2"; + lantiq,gphy-mode = <GPHY_MODE_GE>; + }; + + reset0: reset-controller@10 { + compatible = "lantiq,xrx200-reset"; + reg = <0x10 4>, <0x14 4>; + + #reset-cells = <2>; + }; + + reset1: reset-controller@48 { + compatible = "lantiq,xrx200-reset"; + reg = <0x48 4>, <0x24 4>; + + #reset-cells = <2>; + }; + + usb_phy0: usb2-phy@18 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x18 4>, <0x38 4>; + + resets = <&reset1 4 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; + + usb_phy1: usb2-phy@34 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x34 4>, <0x3C 4>; + + resets = <&reset1 5 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; + + reboot@10 { + compatible = "syscon-reboot"; + reg = <0x10 4>; + + regmap = <&rcu0>; + offset = <0x10>; + mask = <0x40000000>; + }; + }; diff --git a/Documentation/devicetree/bindings/mips/mscc.txt b/Documentation/devicetree/bindings/mips/mscc.txt new file mode 100644 index 000000000..ae15ec333 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/mscc.txt @@ -0,0 +1,43 @@ +* Microsemi MIPS CPUs + +Boards with a SoC of the Microsemi MIPS family shall have the following +properties: + +Required properties: +- compatible: "mscc,ocelot" + + +* Other peripherals: + +o CPU chip regs: + +The SoC has a few registers (DEVCPU_GCB:CHIP_REGS) handling miscellaneous +functionalities: chip ID, general purpose register for software use, reset +controller, hardware status and configuration, efuses. + +Required properties: +- compatible: Should be "mscc,ocelot-chip-regs", "simple-mfd", "syscon" +- reg : Should contain registers location and length + +Example: + syscon@71070000 { + compatible = "mscc,ocelot-chip-regs", "simple-mfd", "syscon"; + reg = <0x71070000 0x1c>; + }; + + +o CPU system control: + +The SoC has a few registers (ICPU_CFG:CPU_SYSTEM_CTRL) handling configuration of +the CPU: 8 general purpose registers, reset control, CPU en/disabling, CPU +endianness, CPU bus control, CPU status. + +Required properties: +- compatible: Should be "mscc,ocelot-cpu-syscon", "syscon" +- reg : Should contain registers location and length + +Example: + syscon@70000000 { + compatible = "mscc,ocelot-cpu-syscon", "syscon"; + reg = <0x70000000 0x2c>; + }; diff --git a/Documentation/devicetree/bindings/mips/ni.txt b/Documentation/devicetree/bindings/mips/ni.txt new file mode 100644 index 000000000..722bf2d62 --- /dev/null +++ b/Documentation/devicetree/bindings/mips/ni.txt @@ -0,0 +1,7 @@ +National Instruments MIPS platforms + +required root node properties: + - compatible: must be "ni,169445" + +CPU Nodes + - compatible: must be "mti,mips14KEc" diff --git a/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt b/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt new file mode 100644 index 000000000..1c8dbc45f --- /dev/null +++ b/Documentation/devicetree/bindings/mips/pic32/microchip,pic32mzda.txt @@ -0,0 +1,31 @@ +* Microchip PIC32MZDA Platforms + +PIC32MZDA Starter Kit +Required root node properties: + - compatible = "microchip,pic32mzda-sk", "microchip,pic32mzda" + +CPU nodes: +---------- +A "cpus" node is required. Required properties: + - #address-cells: Must be 1. + - #size-cells: Must be 0. +A CPU sub-node is also required. Required properties: + - device_type: Must be "cpu". + - compatible: Must be "mti,mips14KEc". +Example: + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "mti,mips14KEc"; + }; + }; + +Boot protocol +-------------- +In accordance with Unified Hosting Interface Reference Manual (MD01069), the +bootloader must pass the following arguments to the kernel: + - $a0: -2. + - $a1: KSEG0 address of the flattened device-tree blob. diff --git a/Documentation/devicetree/bindings/mips/ralink.txt b/Documentation/devicetree/bindings/mips/ralink.txt new file mode 100644 index 000000000..a16e8d7fe --- /dev/null +++ b/Documentation/devicetree/bindings/mips/ralink.txt @@ -0,0 +1,18 @@ +Ralink MIPS SoC device tree bindings + +1. SoCs + +Each device tree must specify a compatible value for the Ralink SoC +it uses in the compatible property of the root node. The compatible +value must be one of the following values: + + ralink,rt2880-soc + ralink,rt3050-soc + ralink,rt3052-soc + ralink,rt3350-soc + ralink,rt3352-soc + ralink,rt3883-soc + ralink,rt5350-soc + ralink,mt7620a-soc + ralink,mt7620n-soc + ralink,mt7628a-soc |