1 files changed, 66 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt
new file mode 100644
index 000000000..cfc376bc9
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/ethernet.txt
@@ -0,0 +1,66 @@
+The following properties are common to the Ethernet controllers:
+
+NOTE: All 'phy*' properties documented below are Ethernet specific. For the
+generic PHY 'phys' property, see
+Documentation/devicetree/bindings/phy/phy-bindings.txt.
+
+- local-mac-address: array of 6 bytes, specifies the MAC address that was
+  assigned to the network device;
+- mac-address: array of 6 bytes, specifies the MAC address that was last used by
+  the boot program; should be used in cases where the MAC address assigned to
+  the device by the boot program is different from the "local-mac-address"
+  property;
+- nvmem-cells: phandle, reference to an nvmem node for the MAC address;
+- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used;
+- max-speed: number, specifies maximum speed in Mbit/s supported by the device;
+- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than
+  the maximum frame size (there's contradiction in the Devicetree
+  Specification).
+- phy-mode: string, operation mode of the PHY interface. This is now a de-facto
+  standard property; supported values are:
+  * "internal"
+  * "mii"
+  * "gmii"
+  * "sgmii"
+  * "qsgmii"
+  * "tbi"
+  * "rev-mii"
+  * "rmii"
+  * "rgmii" (RX and TX delays are added by the MAC when required)
+  * "rgmii-id" (RGMII with internal RX and TX delays provided by the PHY, the
+     MAC should not add the RX or TX delays in this case)
+  * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
+     should not add an RX delay in this case)
+  * "rgmii-txid" (RGMII with internal TX delay provided by the PHY, the MAC
+     should not add an TX delay in this case)
+  * "rtbi"
+  * "smii"
+  * "xgmii"
+  * "trgmii"
+  * "2000base-x",
+  * "2500base-x",
+  * "rxaui"
+  * "xaui"
+  * "10gbase-kr" (10GBASE-KR, XFI, SFI)
+- phy-connection-type: the same as "phy-mode" property but described in the
+  Devicetree Specification;
+- phy-handle: phandle, specifies a reference to a node representing a PHY
+  device; this property is described in the Devicetree Specification and so
+  preferred;
+- phy: the same as "phy-handle" property, not recommended for new bindings.
+- phy-device: the same as "phy-handle" property, not recommended for new
+  bindings.
+- rx-fifo-depth: the size of the controller's receive fifo in bytes. This
+  is used for components that can have configurable receive fifo sizes,
+  and is useful for determining certain configuration settings such as
+  flow control thresholds.
+- tx-fifo-depth: the size of the controller's transmit fifo in bytes. This
+  is used for components that can have configurable fifo sizes.
+- managed: string, specifies the PHY management type. Supported values are:
+  "auto", "in-band-status". "auto" is the default, it usess MDIO for
+  management if fixed-link is not specified.
+
+Child nodes of the Ethernet controller are typically the individual PHY devices
+connected via the MDIO bus (sometimes the MDIO bus controller is separate).
+They are described in the phy.txt file in this same directory.
+For non-MDIO PHY management see fixed-link.txt.