diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net')
166 files changed, 10522 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt new file mode 100644 index 000000000..e98118aef --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-emac.txt @@ -0,0 +1,19 @@ +* Allwinner EMAC ethernet controller + +Required properties: +- compatible: should be "allwinner,sun4i-a10-emac" (Deprecated: + "allwinner,sun4i-emac") +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device +- phy: see ethernet.txt file in the same directory. +- clocks: A phandle to the reference clock for this device + +Example: + +emac: ethernet@1c0b000 { + compatible = "allwinner,sun4i-a10-emac"; + reg = <0x01c0b000 0x1000>; + interrupts = <55>; + clocks = <&ahb_gates 17>; + phy = <&phy0>; +}; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt new file mode 100644 index 000000000..ab5b8613b --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun4i-mdio.txt @@ -0,0 +1,27 @@ +* Allwinner A10 MDIO Ethernet Controller interface + +Required properties: +- compatible: should be "allwinner,sun4i-a10-mdio" + (Deprecated: "allwinner,sun4i-mdio"). +- reg: address and length of the register set for the device. + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one + +Example at the SoC level: +mdio@1c0b080 { + compatible = "allwinner,sun4i-a10-mdio"; + reg = <0x01c0b080 0x14>; + #address-cells = <1>; + #size-cells = <0>; +}; + +And at the board level: + +mdio@1c0b080 { + phy-supply = <®_emac_3v3>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.txt b/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.txt new file mode 100644 index 000000000..8b3f95365 --- /dev/null +++ b/Documentation/devicetree/bindings/net/allwinner,sun7i-a20-gmac.txt @@ -0,0 +1,27 @@ +* Allwinner GMAC ethernet controller + +This device is a platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +Required properties: + - compatible: Should be "allwinner,sun7i-a20-gmac" + - clocks: Should contain the GMAC main clock, and tx clock + The tx clock type should be "allwinner,sun7i-a20-gmac-clk" + - clock-names: Should contain the clock names "stmmaceth", + and "allwinner_gmac_tx" + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one + +Examples: + + gmac: ethernet@1c50000 { + compatible = "allwinner,sun7i-a20-gmac"; + reg = <0x01c50000 0x10000>, + <0x01c20164 0x4>; + interrupts = <0 85 1>; + interrupt-names = "macirq"; + clocks = <&ahb_gates 49>, <&gmac_tx>; + clock-names = "stmmaceth", "allwinner_gmac_tx"; + phy-mode = "mii"; + }; diff --git a/Documentation/devicetree/bindings/net/altera_tse.txt b/Documentation/devicetree/bindings/net/altera_tse.txt new file mode 100644 index 000000000..0e21df94a --- /dev/null +++ b/Documentation/devicetree/bindings/net/altera_tse.txt @@ -0,0 +1,114 @@ +* Altera Triple-Speed Ethernet MAC driver (TSE) + +Required properties: +- compatible: Should be "altr,tse-1.0" for legacy SGDMA based TSE, and should + be "altr,tse-msgdma-1.0" for the preferred MSGDMA based TSE. + ALTR is supported for legacy device trees, but is deprecated. + altr should be used for all new designs. +- reg: Address and length of the register set for the device. It contains + the information of registers in the same order as described by reg-names +- reg-names: Should contain the reg names + "control_port": MAC configuration space region + "tx_csr": xDMA Tx dispatcher control and status space region + "tx_desc": MSGDMA Tx dispatcher descriptor space region + "rx_csr" : xDMA Rx dispatcher control and status space region + "rx_desc": MSGDMA Rx dispatcher descriptor space region + "rx_resp": MSGDMA Rx dispatcher response space region + "s1": SGDMA descriptor memory +- interrupts: Should contain the TSE interrupts and it's mode. +- interrupt-names: Should contain the interrupt names + "rx_irq": xDMA Rx dispatcher interrupt + "tx_irq": xDMA Tx dispatcher interrupt +- rx-fifo-depth: MAC receive FIFO buffer depth in bytes +- tx-fifo-depth: MAC transmit FIFO buffer depth in bytes +- phy-mode: See ethernet.txt in the same directory. +- phy-handle: See ethernet.txt in the same directory. +- phy-addr: See ethernet.txt in the same directory. A configuration should + include phy-handle or phy-addr. +- altr,has-supplementary-unicast: + If present, TSE supports additional unicast addresses. + Otherwise additional unicast addresses are not supported. +- altr,has-hash-multicast-filter: + If present, TSE supports a hash based multicast filter. + Otherwise, hash-based multicast filtering is not supported. + +- mdio device tree subnode: When the TSE has a phy connected to its local + mdio, there must be device tree subnode with the following + required properties: + + - compatible: Must be "altr,tse-mdio". + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For each phy on the mdio bus, there must be a node with the following + fields: + + - reg: phy id used to communicate to phy. + - device_type: Must be "ethernet-phy". + +Optional properties: +- local-mac-address: See ethernet.txt in the same directory. +- max-frame-size: See ethernet.txt in the same directory. + +Example: + + tse_sub_0_eth_tse_0: ethernet@1,00000000 { + compatible = "altr,tse-msgdma-1.0"; + reg = <0x00000001 0x00000000 0x00000400>, + <0x00000001 0x00000460 0x00000020>, + <0x00000001 0x00000480 0x00000020>, + <0x00000001 0x000004A0 0x00000008>, + <0x00000001 0x00000400 0x00000020>, + <0x00000001 0x00000420 0x00000020>; + reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 41 4>, <0 40 4>; + interrupt-names = "rx_irq", "tx_irq"; + rx-fifo-depth = <2048>; + tx-fifo-depth = <2048>; + address-bits = <48>; + max-frame-size = <1500>; + local-mac-address = [ 00 00 00 00 00 00 ]; + phy-mode = "gmii"; + altr,has-supplementary-unicast; + altr,has-hash-multicast-filter; + phy-handle = <&phy0>; + mdio { + compatible = "altr,tse-mdio"; + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <0x0>; + device_type = "ethernet-phy"; + }; + + phy1: ethernet-phy@1 { + reg = <0x1>; + device_type = "ethernet-phy"; + }; + + }; + }; + + tse_sub_1_eth_tse_0: ethernet@1,00001000 { + compatible = "altr,tse-msgdma-1.0"; + reg = <0x00000001 0x00001000 0x00000400>, + <0x00000001 0x00001460 0x00000020>, + <0x00000001 0x00001480 0x00000020>, + <0x00000001 0x000014A0 0x00000008>, + <0x00000001 0x00001400 0x00000020>, + <0x00000001 0x00001420 0x00000020>; + reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp", "tx_csr", "tx_desc"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 43 4>, <0 42 4>; + interrupt-names = "rx_irq", "tx_irq"; + rx-fifo-depth = <2048>; + tx-fifo-depth = <2048>; + address-bits = <48>; + max-frame-size = <1500>; + local-mac-address = [ 00 00 00 00 00 00 ]; + phy-mode = "gmii"; + altr,has-supplementary-unicast; + altr,has-hash-multicast-filter; + phy-handle = <&phy1>; + }; diff --git a/Documentation/devicetree/bindings/net/amd-xgbe.txt b/Documentation/devicetree/bindings/net/amd-xgbe.txt new file mode 100644 index 000000000..93dcb79a5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/amd-xgbe.txt @@ -0,0 +1,75 @@ +* AMD 10GbE driver (amd-xgbe) + +Required properties: +- compatible: Should be "amd,xgbe-seattle-v1a" +- reg: Address and length of the register sets for the device + - MAC registers + - PCS registers + - SerDes Rx/Tx registers + - SerDes integration registers (1/2) + - SerDes integration registers (2/2) +- interrupts: Should contain the amd-xgbe interrupt(s). The first interrupt + listed is required and is the general device interrupt. If the optional + amd,per-channel-interrupt property is specified, then one additional + interrupt for each DMA channel supported by the device should be specified. + The last interrupt listed should be the PCS auto-negotiation interrupt. +- clocks: + - DMA clock for the amd-xgbe device (used for calculating the + correct Rx interrupt watchdog timer value on a DMA channel + for coalescing) + - PTP clock for the amd-xgbe device +- clock-names: Should be the names of the clocks + - "dma_clk" for the DMA clock + - "ptp_clk" for the PTP clock +- phy-mode: See ethernet.txt file in the same directory + +Optional properties: +- mac-address: mac address to be assigned to the device. Can be overridden + by UEFI. +- dma-coherent: Present if dma operations are coherent +- amd,per-channel-interrupt: Indicates that Rx and Tx complete will generate + a unique interrupt for each DMA channel - this requires an additional + interrupt be configured for each DMA channel +- amd,speed-set: Speed capabilities of the device + 0 - 1GbE and 10GbE (default) + 1 - 2.5GbE and 10GbE + +The following optional properties are represented by an array with each +value corresponding to a particular speed. The first array value represents +the setting for the 1GbE speed, the second value for the 2.5GbE speed and +the third value for the 10GbE speed. All three values are required if the +property is used. +- amd,serdes-blwc: Baseline wandering correction enablement + 0 - Off + 1 - On +- amd,serdes-cdr-rate: CDR rate speed selection +- amd,serdes-pq-skew: PQ (data sampling) skew +- amd,serdes-tx-amp: TX amplitude boost +- amd,serdes-dfe-tap-config: DFE taps available to run +- amd,serdes-dfe-tap-enable: DFE taps to enable + +Example: + xgbe@e0700000 { + compatible = "amd,xgbe-seattle-v1a"; + reg = <0 0xe0700000 0 0x80000>, + <0 0xe0780000 0 0x80000>, + <0 0xe1240800 0 0x00400>, + <0 0xe1250000 0 0x00060>, + <0 0xe1250080 0 0x00004>; + interrupt-parent = <&gic>; + interrupts = <0 325 4>, + <0 326 1>, <0 327 1>, <0 328 1>, <0 329 1>, + <0 323 4>; + amd,per-channel-interrupt; + clocks = <&xgbe_dma_clk>, <&xgbe_ptp_clk>; + clock-names = "dma_clk", "ptp_clk"; + phy-mode = "xgmii"; + mac-address = [ 02 a1 a2 a3 a4 a5 ]; + amd,speed-set = <0>; + amd,serdes-blwc = <1>, <1>, <0>; + amd,serdes-cdr-rate = <2>, <2>, <7>; + amd,serdes-pq-skew = <10>, <10>, <30>; + amd,serdes-tx-amp = <15>, <15>, <10>; + amd,serdes-dfe-tap-config = <3>, <3>, <1>; + amd,serdes-dfe-tap-enable = <0>, <0>, <127>; + }; diff --git a/Documentation/devicetree/bindings/net/anarion-gmac.txt b/Documentation/devicetree/bindings/net/anarion-gmac.txt new file mode 100644 index 000000000..fe678965a --- /dev/null +++ b/Documentation/devicetree/bindings/net/anarion-gmac.txt @@ -0,0 +1,25 @@ +* Adaptrum Anarion ethernet controller + +This device is a platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +Required properties: + - compatible: Should be "adaptrum,anarion-gmac", "snps,dwmac" + - phy-mode: Should be "rgmii". Other modes are not currently supported. + + +Examples: + + gmac1: ethernet@f2014000 { + compatible = "adaptrum,anarion-gmac", "snps,dwmac"; + reg = <0xf2014000 0x4000>, <0xf2018100 8>; + + interrupt-parent = <&core_intc>; + interrupts = <21>; + interrupt-names = "macirq"; + + clocks = <&core_clk>; + clock-names = "stmmaceth"; + + phy-mode = "rgmii"; + }; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-enet.txt b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt new file mode 100644 index 000000000..f591ab782 --- /dev/null +++ b/Documentation/devicetree/bindings/net/apm-xgene-enet.txt @@ -0,0 +1,91 @@ +APM X-Gene SoC Ethernet nodes + +Ethernet nodes are defined to describe on-chip ethernet interfaces in +APM X-Gene SoC. + +Required properties for all the ethernet interfaces: +- compatible: Should state binding information from the following list, + - "apm,xgene-enet": RGMII based 1G interface + - "apm,xgene1-sgenet": SGMII based 1G interface + - "apm,xgene1-xgenet": XFI based 10G interface +- reg: Address and length of the register set for the device. It contains the + information of registers in the same order as described by reg-names +- reg-names: Should contain the register set names + - "enet_csr": Ethernet control and status register address space + - "ring_csr": Descriptor ring control and status register address space + - "ring_cmd": Descriptor ring command register address space +- interrupts: Two interrupt specifiers can be specified. + - First is the Rx interrupt. This irq is mandatory. + - Second is the Tx completion interrupt. + This is supported only on SGMII based 1GbE and 10GbE interfaces. +- channel: Ethernet to CPU, start channel (prefetch buffer) number + - Must map to the first irq and irqs must be sequential +- port-id: Port number (0 or 1) +- clocks: Reference to the clock entry. +- local-mac-address: MAC address assigned to this device +- phy-connection-type: Interface type between ethernet device and PHY device + +Required properties for ethernet interfaces that have external PHY: +- phy-handle: Reference to a PHY node connected to this device + +- mdio: Device tree subnode with the following required properties: + - compatible: Must be "apm,xgene-mdio". + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For the phy on the mdio bus, there must be a node with the following fields: + - compatible: PHY identifier. Please refer ./phy.txt for the format. + - reg: The ID number for the phy. + +Optional properties: +- status: Should be "ok" or "disabled" for enabled/disabled. Default is "ok". +- tx-delay: Delay value for RGMII bridge TX clock. + Valid values are between 0 to 7, that maps to + 417, 717, 1020, 1321, 1611, 1913, 2215, 2514 ps + Default value is 4, which corresponds to 1611 ps +- rx-delay: Delay value for RGMII bridge RX clock. + Valid values are between 0 to 7, that maps to + 273, 589, 899, 1222, 1480, 1806, 2147, 2464 ps + Default value is 2, which corresponds to 899 ps +- rxlos-gpios: Input gpio from SFP+ module to indicate availability of + incoming signal. + + +Example: + menetclk: menetclk { + compatible = "apm,xgene-device-clock"; + clock-output-names = "menetclk"; + status = "ok"; + }; + + menet: ethernet@17020000 { + compatible = "apm,xgene-enet"; + status = "disabled"; + reg = <0x0 0x17020000 0x0 0xd100>, + <0x0 0x17030000 0x0 0x400>, + <0x0 0x10000000 0x0 0x200>; + reg-names = "enet_csr", "ring_csr", "ring_cmd"; + interrupts = <0x0 0x3c 0x4>; + port-id = <0>; + clocks = <&menetclk 0>; + local-mac-address = [00 01 73 00 00 01]; + phy-connection-type = "rgmii"; + phy-handle = <&menetphy>; + mdio { + compatible = "apm,xgene-mdio"; + #address-cells = <1>; + #size-cells = <0>; + menetphy: menetphy@3 { + compatible = "ethernet-phy-id001c.c915"; + reg = <0x3>; + }; + + }; + }; + +/* Board-specific peripheral configurations */ +&menet { + tx-delay = <4>; + rx-delay = <2>; + status = "ok"; +}; diff --git a/Documentation/devicetree/bindings/net/apm-xgene-mdio.txt b/Documentation/devicetree/bindings/net/apm-xgene-mdio.txt new file mode 100644 index 000000000..78722d74c --- /dev/null +++ b/Documentation/devicetree/bindings/net/apm-xgene-mdio.txt @@ -0,0 +1,37 @@ +APM X-Gene SoC MDIO node + +MDIO node is defined to describe on-chip MDIO controller. + +Required properties: + - compatible: Must be "apm,xgene-mdio-rgmii" or "apm,xgene-mdio-xfi" + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + - reg: Address and length of the register set + - clocks: Reference to the clock entry + +For the phys on the mdio bus, there must be a node with the following fields: + - compatible: PHY identifier. Please refer ./phy.txt for the format. + - reg: The ID number for the phy. + +Example: + + mdio: mdio@17020000 { + compatible = "apm,xgene-mdio-rgmii"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x0 0x17020000 0x0 0xd100>; + clocks = <&menetclk 0>; + }; + + /* Board-specific peripheral configurations */ + &mdio { + menetphy: phy@3 { + reg = <0x3>; + }; + sgenet0phy: phy@4 { + reg = <0x4>; + }; + sgenet1phy: phy@5 { + reg = <0x5>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/arc_emac.txt b/Documentation/devicetree/bindings/net/arc_emac.txt new file mode 100644 index 000000000..c73a0e9c6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/arc_emac.txt @@ -0,0 +1,46 @@ +* Synopsys ARC EMAC 10/100 Ethernet driver (EMAC) + +Required properties: +- compatible: Should be "snps,arc-emac" +- reg: Address and length of the register set for the device +- interrupts: Should contain the EMAC interrupts +- max-speed: see ethernet.txt file in the same directory. +- phy: see ethernet.txt file in the same directory. + +Optional properties: +- phy-reset-gpios : Should specify the gpio for phy reset +- phy-reset-duration : Reset duration in milliseconds. Should present + only if property "phy-reset-gpios" is available. Missing the property + will have the duration be 1 millisecond. Numbers greater than 1000 are + invalid and 1 millisecond will be used instead. + +Clock handling: +The clock frequency is needed to calculate and set polling period of EMAC. +It must be provided by one of: +- clock-frequency: CPU frequency. +- clocks: reference to the clock supplying the EMAC. + +Child nodes of the driver are the individual PHY devices connected to the +MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. + +Examples: + + ethernet@c0fc2000 { + compatible = "snps,arc-emac"; + reg = <0xc0fc2000 0x3c>; + interrupts = <6>; + mac-address = [ 00 11 22 33 44 55 ]; + + clock-frequency = <80000000>; + /* or */ + clocks = <&emac_clock>; + + max-speed = <100>; + phy = <&phy0>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/bluetooth.txt b/Documentation/devicetree/bindings/net/bluetooth.txt new file mode 100644 index 000000000..94797df75 --- /dev/null +++ b/Documentation/devicetree/bindings/net/bluetooth.txt @@ -0,0 +1,5 @@ +The following properties are common to the Bluetooth controllers: + +- local-bd-address: array of 6 bytes, specifies the BD address that was + uniquely assigned to the Bluetooth device, formatted with least significant + byte first (little-endian). diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt new file mode 100644 index 000000000..0bfad656a --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,amac.txt @@ -0,0 +1,30 @@ +Broadcom AMAC Ethernet Controller Device Tree Bindings +------------------------------------------------------------- + +Required properties: + - compatible: "brcm,amac" + "brcm,nsp-amac" + "brcm,ns2-amac" + - reg: Address and length of the register set for the device. It + contains the information of registers in the same order as + described by reg-names + - reg-names: Names of the registers. + "amac_base": Address and length of the GMAC registers + "idm_base": Address and length of the GMAC IDM registers + (required for NSP and Northstar2) + "nicpm_base": Address and length of the NIC Port Manager + registers (required for Northstar2) + - interrupts: Interrupt number + +Optional properties: +- mac-address: See ethernet.txt file in the same directory + +Examples: + +amac0: ethernet@18022000 { + compatible = "brcm,nsp-amac"; + reg = <0x18022000 0x1000>, + <0x18110000 0x1000>; + reg-names = "amac_base", "idm_base"; + interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt new file mode 100644 index 000000000..b7336b9d6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,bcm7445-switch-v4.0.txt @@ -0,0 +1,132 @@ +* Broadcom Starfighter 2 integrated swich + +Required properties: + +- compatible: should be one of + "brcm,bcm7445-switch-v4.0" + "brcm,bcm7278-switch-v4.0" + "brcm,bcm7278-switch-v4.8" +- reg: addresses and length of the register sets for the device, must be 6 + pairs of register addresses and lengths +- interrupts: interrupts for the devices, must be two interrupts +- #address-cells: must be 1, see dsa/dsa.txt +- #size-cells: must be 0, see dsa/dsa.txt + +Deprecated binding required properties: + +- dsa,mii-bus: phandle to the MDIO bus controller, see dsa/dsa.txt +- dsa,ethernet: phandle to the CPU network interface controller, see dsa/dsa.txt +- #address-cells: must be 2, see dsa/dsa.txt + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. + +Optional properties: + +- reg-names: litteral names for the device base register addresses, when present + must be: "core", "reg", "intrl2_0", "intrl2_1", "fcb", "acb" + +- interrupt-names: litternal names for the device interrupt lines, when present + must be: "switch_0" and "switch_1" + +- brcm,num-gphy: specify the maximum number of integrated gigabit PHYs in the + switch + +- brcm,num-rgmii-ports: specify the maximum number of RGMII interfaces supported + by the switch + +- brcm,fcb-pause-override: boolean property, if present indicates that the switch + supports Failover Control Block pause override capability + +- brcm,acb-packets-inflight: boolean property, if present indicates that the switch + Admission Control Block supports reporting the number of packets in-flight in a + switch queue + +Port subnodes: + +Optional properties: + +- brcm,use-bcm-hdr: boolean property, if present, indicates that the switch + port has Broadcom tags enabled (per-packet metadata) + +Example: + +switch_top@f0b00000 { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0 0xf0b00000 0x40804>; + + ethernet_switch@0 { + compatible = "brcm,bcm7445-switch-v4.0"; + #size-cells = <0>; + #address-cells = <1>; + reg = <0x0 0x40000 + 0x40000 0x110 + 0x40340 0x30 + 0x40380 0x30 + 0x40400 0x34 + 0x40600 0x208>; + reg-names = "core", "reg", intrl2_0", "intrl2_1", + "fcb, "acb"; + interrupts = <0 0x18 0 + 0 0x19 0>; + brcm,num-gphy = <1>; + brcm,num-rgmii-ports = <2>; + brcm,fcb-pause-override; + brcm,acb-packets-inflight; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + label = "gphy"; + reg = <0>; + }; + }; + }; +}; + +Example using the old DSA DeviceTree binding: + +switch_top@f0b00000 { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0 0xf0b00000 0x40804>; + + ethernet_switch@0 { + compatible = "brcm,bcm7445-switch-v4.0"; + #size-cells = <0>; + #address-cells = <2>; + reg = <0x0 0x40000 + 0x40000 0x110 + 0x40340 0x30 + 0x40380 0x30 + 0x40400 0x34 + 0x40600 0x208>; + interrupts = <0 0x18 0 + 0 0x19 0>; + brcm,num-gphy = <1>; + brcm,num-rgmii-ports = <2>; + brcm,fcb-pause-override; + brcm,acb-packets-inflight; + + ... + switch@0 { + reg = <0 0>; + #size-cells = <0>; + #address-cells <1>; + + port@0 { + label = "gphy"; + reg = <0>; + brcm,use-bcm-hdr; + }; + ... + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt new file mode 100644 index 000000000..3956af1d3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,bcmgenet.txt @@ -0,0 +1,124 @@ +* Broadcom BCM7xxx Ethernet Controller (GENET) + +Required properties: +- compatible: should contain one of "brcm,genet-v1", "brcm,genet-v2", + "brcm,genet-v3", "brcm,genet-v4", "brcm,genet-v5". +- reg: address and length of the register set for the device +- interrupts and/or interrupts-extended: must be two cells, the first cell + is the general purpose interrupt line, while the second cell is the + interrupt for the ring RX and TX queues operating in ring mode. An + optional third interrupt cell for Wake-on-LAN can be specified. + See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt + for information on the property specifics. +- phy-mode: see ethernet.txt file in the same directory +- #address-cells: should be 1 +- #size-cells: should be 1 + +Optional properties: +- clocks: When provided, must be two phandles to the functional clocks nodes + of the GENET block. The first phandle is the main GENET clock used during + normal operation, while the second phandle is the Wake-on-LAN clock. +- clock-names: When provided, names of the functional clock phandles, first + name should be "enet" and second should be "enet-wol". + +- phy-handle: See ethernet.txt file in the same directory; used to describe + configurations where a PHY (internal or external) is used. + +- fixed-link: When the GENET interface is connected to a MoCA hardware block or + when operating in a RGMII to RGMII type of connection, or when the MDIO bus is + voluntarily disabled, this property should be used to describe the "fixed link". + See Documentation/devicetree/bindings/net/fixed-link.txt for information on + the property specifics + +Required child nodes: + +- mdio bus node: this node should always be present regardless of the PHY + configuration of the GENET instance + +MDIO bus node required properties: + +- compatible: should contain one of "brcm,genet-mdio-v1", "brcm,genet-mdio-v2" + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", "brcm,genet-mdio-v5", the version + has to match the parent node compatible property (e.g: brcm,genet-v4 pairs + with brcm,genet-mdio-v4) +- reg: address and length relative to the parent node base register address +- #address-cells: address cell for MDIO bus addressing, should be 1 +- #size-cells: size of the cells for MDIO bus addressing, should be 0 + +Ethernet PHY node properties: + +See Documentation/devicetree/bindings/net/phy.txt for the list of required and +optional properties. + +Internal Gigabit PHY example: + +ethernet@f0b60000 { + phy-mode = "internal"; + phy-handle = <&phy1>; + mac-address = [ 00 10 18 36 23 1a ]; + compatible = "brcm,genet-v4"; + #address-cells = <0x1>; + #size-cells = <0x1>; + reg = <0xf0b60000 0xfc4c>; + interrupts = <0x0 0x14 0x0>, <0x0 0x15 0x0>; + + mdio@e14 { + compatible = "brcm,genet-mdio-v4"; + #address-cells = <0x1>; + #size-cells = <0x0>; + reg = <0xe14 0x8>; + + phy1: ethernet-phy@1 { + max-speed = <1000>; + reg = <0x1>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + }; +}; + +MoCA interface / MAC to MAC example: + +ethernet@f0b80000 { + phy-mode = "moca"; + fixed-link = <1 0 1000 0 0>; + mac-address = [ 00 10 18 36 24 1a ]; + compatible = "brcm,genet-v4"; + #address-cells = <0x1>; + #size-cells = <0x1>; + reg = <0xf0b80000 0xfc4c>; + interrupts = <0x0 0x16 0x0>, <0x0 0x17 0x0>; + + mdio@e14 { + compatible = "brcm,genet-mdio-v4"; + #address-cells = <0x1>; + #size-cells = <0x0>; + reg = <0xe14 0x8>; + }; +}; + + +External MDIO-connected Gigabit PHY/switch: + +ethernet@f0ba0000 { + phy-mode = "rgmii"; + phy-handle = <&phy0>; + mac-address = [ 00 10 18 36 26 1a ]; + compatible = "brcm,genet-v4"; + #address-cells = <0x1>; + #size-cells = <0x1>; + reg = <0xf0ba0000 0xfc4c>; + interrupts = <0x0 0x18 0x0>, <0x0 0x19 0x0>; + + mdio@e14 { + compatible = "brcm,genet-mdio-v4"; + #address-cells = <0x1>; + #size-cells = <0x0>; + reg = <0xe14 0x8>; + + phy0: ethernet-phy@0 { + max-speed = <1000>; + reg = <0x0>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt b/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt new file mode 100644 index 000000000..8ba9ed11d --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,iproc-mdio.txt @@ -0,0 +1,23 @@ +* Broadcom iProc MDIO bus controller + +Required properties: +- compatible: should be "brcm,iproc-mdio" +- reg: address and length of the register set for the MDIO interface +- #size-cells: must be 1 +- #address-cells: must be 0 + +Child nodes of this MDIO bus controller node are standard Ethernet PHY device +nodes as described in Documentation/devicetree/bindings/net/phy.txt + +Example: + +mdio@18002000 { + compatible = "brcm,iproc-mdio"; + reg = <0x18002000 0x8>; + #size-cells = <1>; + #address-cells = <0>; + + enet-gphy@0 { + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt new file mode 100644 index 000000000..b58843f29 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,mdio-mux-iproc.txt @@ -0,0 +1,62 @@ +Properties for an MDIO bus multiplexer found in Broadcom iProc based SoCs. + +This MDIO bus multiplexer defines buses that could be internal as well as +external to SoCs and could accept MDIO transaction compatible to C-22 or +C-45 Clause. When child bus is selected, one needs to select these two +properties as well to generate desired MDIO transaction on appropriate bus. + +Required properties in addition to the generic multiplexer properties: + +MDIO multiplexer node: +- compatible: brcm,mdio-mux-iproc. + +Every non-ethernet PHY requires a compatible so that it could be probed based +on this compatible string. + +Optional properties: +- clocks: phandle of the core clock which drives the mdio block. + +Additional information regarding generic multiplexer properties can be found +at- Documentation/devicetree/bindings/net/mdio-mux.txt + + +for example: + mdio_mux_iproc: mdio-mux@66020000 { + compatible = "brcm,mdio-mux-iproc"; + reg = <0x66020000 0x250>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + pci_phy0: pci-phy@0 { + compatible = "brcm,ns2-pcie-phy"; + reg = <0x0>; + #phy-cells = <0>; + }; + }; + + mdio@7 { + reg = <0x7>; + #address-cells = <1>; + #size-cells = <0>; + + pci_phy1: pci-phy@0 { + compatible = "brcm,ns2-pcie-phy"; + reg = <0x0>; + #phy-cells = <0>; + }; + }; + mdio@10 { + reg = <0x10>; + #address-cells = <1>; + #size-cells = <0>; + + gphy0: eth-phy@10 { + reg = <0x10>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/brcm,systemport.txt b/Documentation/devicetree/bindings/net/brcm,systemport.txt new file mode 100644 index 000000000..83f29e0e1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,systemport.txt @@ -0,0 +1,33 @@ +* Broadcom BCM7xxx Ethernet Systemport Controller (SYSTEMPORT) + +Required properties: +- compatible: should be one of: + "brcm,systemport-v1.00" + "brcm,systemportlite-v1.00" or + "brcm,systemport" +- reg: address and length of the register set for the device. +- interrupts: interrupts for the device, first cell must be for the rx + interrupts, and the second cell should be for the transmit queues. An + optional third interrupt cell for Wake-on-LAN can be specified +- local-mac-address: Ethernet MAC address (48 bits) of this adapter +- phy-mode: Should be a string describing the PHY interface to the + Ethernet switch/PHY, see Documentation/devicetree/bindings/net/ethernet.txt +- fixed-link: see Documentation/devicetree/bindings/net/fixed-link.txt for + the property specific details + +Optional properties: +- systemport,num-tier2-arb: number of tier 2 arbiters, an integer +- systemport,num-tier1-arb: number of tier 1 arbiters, an integer +- systemport,num-txq: number of HW transmit queues, an integer +- systemport,num-rxq: number of HW receive queues, an integer + +Example: +ethernet@f04a0000 { + compatible = "brcm,systemport-v1.00"; + reg = <0xf04a0000 0x4650>; + local-mac-address = [ 00 11 22 33 44 55 ]; + fixed-link = <0 1 1000 0 0>; + phy-mode = "gmii"; + interrupts = <0x0 0x16 0x0>, + <0x0 0x17 0x0>; +}; diff --git a/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt new file mode 100644 index 000000000..e15589f47 --- /dev/null +++ b/Documentation/devicetree/bindings/net/brcm,unimac-mdio.txt @@ -0,0 +1,43 @@ +* Broadcom UniMAC MDIO bus controller + +Required properties: +- compatible: should one from "brcm,genet-mdio-v1", "brcm,genet-mdio-v2", + "brcm,genet-mdio-v3", "brcm,genet-mdio-v4", "brcm,genet-mdio-v5" or + "brcm,unimac-mdio" +- reg: address and length of the register set for the device, first one is the + base register, and the second one is optional and for indirect accesses to + larger than 16-bits MDIO transactions +- reg-names: name(s) of the register must be "mdio" and optional "mdio_indir_rw" +- #size-cells: must be 1 +- #address-cells: must be 0 + +Optional properties: +- interrupts: must be one if the interrupt is shared with the Ethernet MAC or + Ethernet switch this MDIO block is integrated from, or must be two, if there + are two separate interrupts, first one must be "mdio done" and second must be + for "mdio error" +- interrupt-names: must be "mdio_done_error" when there is a share interrupt fed + to this hardware block, or must be "mdio_done" for the first interrupt and + "mdio_error" for the second when there are separate interrupts +- clocks: A reference to the clock supplying the MDIO bus controller +- clock-frequency: the MDIO bus clock that must be output by the MDIO bus + hardware, if absent, the default hardware values are used + +Child nodes of this MDIO bus controller node are standard Ethernet PHY device +nodes as described in Documentation/devicetree/bindings/net/phy.txt + +Example: + +mdio@403c0 { + compatible = "brcm,unimac-mdio"; + reg = <0x403c0 0x8 0x40300 0x18>; + reg-names = "mdio", "mdio_indir_rw"; + #size-cells = <1>; + #address-cells = <0>; + + ... + phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt new file mode 100644 index 000000000..7c86d5e28 --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-bcm87xx.txt @@ -0,0 +1,29 @@ +The Broadcom BCM87XX devices are a family of 10G Ethernet PHYs. They +have these bindings in addition to the standard PHY bindings. + +Compatible: Should contain "broadcom,bcm8706" or "broadcom,bcm8727" and + "ethernet-phy-ieee802.3-c45" + +Optional Properties: + +- broadcom,c45-reg-init : one of more sets of 4 cells. The first cell + is the MDIO Manageable Device (MMD) address, the second a register + address within the MMD, the third cell contains a mask to be ANDed + with the existing register value, and the fourth cell is ORed with + he result to yield the new register value. If the third cell has a + value of zero, no read of the existing value is performed. + +Example: + + ethernet-phy@5 { + reg = <5>; + compatible = "broadcom,bcm8706", "ethernet-phy-ieee802.3-c45"; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + /* + * Set PMD Digital Control Register for + * GPIO[1] Tx/Rx + * GPIO[0] R64 Sync Acquired + */ + broadcom,c45-reg-init = <1 0xc808 0xff8f 0x70>; + }; diff --git a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt new file mode 100644 index 000000000..4194ff7e6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt @@ -0,0 +1,35 @@ +Broadcom Bluetooth Chips +--------------------- + +This documents the binding structure and common properties for serial +attached Broadcom devices. + +Serial attached Broadcom devices shall be a child node of the host UART +device the slave device is attached to. + +Required properties: + + - compatible: should contain one of the following: + * "brcm,bcm43438-bt" + +Optional properties: + + - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt + - shutdown-gpios: GPIO specifier, used to enable the BT module + - device-wakeup-gpios: GPIO specifier, used to wakeup the controller + - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor + - clocks: clock specifier if external clock provided to the controller + - clock-names: should be "extclk" + + +Example: + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + max-speed = <921600>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/btusb.txt b/Documentation/devicetree/bindings/net/btusb.txt new file mode 100644 index 000000000..d883a3564 --- /dev/null +++ b/Documentation/devicetree/bindings/net/btusb.txt @@ -0,0 +1,41 @@ +Generic Bluetooth controller over USB (btusb driver) +--------------------------------------------------- + +Required properties: + + - compatible : should comply with the format "usbVID,PID" specified in + Documentation/devicetree/bindings/usb/usb-device.txt + At the time of writing, the only OF supported devices + (more may be added later) are: + + "usb1286,204e" (Marvell 8997) + +Also, vendors that use btusb may have device additional properties, e.g: +Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt + +Optional properties: + + - interrupt-names: (see below) + - interrupts : The interrupt specified by the name "wakeup" is the interrupt + that shall be used for out-of-band wake-on-bt. Driver will + request this interrupt for wakeup. During system suspend, the + irq will be enabled so that the bluetooth chip can wakeup host + platform out of band. During system resume, the irq will be + disabled to make sure unnecessary interrupt is not received. + +Example: + +Following example uses irq pin number 3 of gpio0 for out of band wake-on-bt: + +&usb_host1_ehci { + #address-cells = <1>; + #size-cells = <0>; + + mvl_bt1: bt@1 { + compatible = "usb1286,204e"; + reg = <1>; + interrupt-parent = <&gpio0>; + interrupt-names = "wakeup"; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/calxeda-xgmac.txt b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt new file mode 100644 index 000000000..c8ae996bd --- /dev/null +++ b/Documentation/devicetree/bindings/net/calxeda-xgmac.txt @@ -0,0 +1,18 @@ +* Calxeda Highbank 10Gb XGMAC Ethernet + +Required properties: +- compatible : Should be "calxeda,hb-xgmac" +- reg : Address and length of the register set for the device +- interrupts : Should contain 3 xgmac interrupts. The 1st is main interrupt. + The 2nd is pwr mgt interrupt. The 3rd is low power state interrupt. + +Optional properties: +- dma-coherent : Present if dma operations are coherent + +Example: + +ethernet@fff50000 { + compatible = "calxeda,hb-xgmac"; + reg = <0xfff50000 0x1000>; + interrupts = <0 77 4 0 78 4 0 79 4>; +}; diff --git a/Documentation/devicetree/bindings/net/can/atmel-can.txt b/Documentation/devicetree/bindings/net/can/atmel-can.txt new file mode 100644 index 000000000..14e52a0d8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/atmel-can.txt @@ -0,0 +1,14 @@ +* AT91 CAN * + +Required properties: + - compatible: Should be "atmel,at91sam9263-can" or "atmel,at91sam9x5-can" + - reg: Should contain CAN controller registers location and length + - interrupts: Should contain IRQ line for the CAN controller + +Example: + + can0: can@f000c000 { + compatible = "atmel,at91sam9x5-can"; + reg = <0xf000c000 0x300>; + interrupts = <40 4 5> + }; diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt new file mode 100644 index 000000000..2d504256b --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/c_can.txt @@ -0,0 +1,65 @@ +Bosch C_CAN/D_CAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "bosch,c_can" for C_CAN controllers and + "bosch,d_can" for D_CAN controllers. + Can be "ti,dra7-d_can", "ti,am3352-d_can" or + "ti,am4372-d_can". +- reg : physical base address and size of the C_CAN/D_CAN + registers map +- interrupts : property with a value describing the interrupt + number + +The following are mandatory properties for DRA7x, AM33xx and AM43xx SoCs only: +- ti,hwmods : Must be "d_can<n>" or "c_can<n>", n being the + instance number + +The following are mandatory properties for Keystone 2 66AK2G SoCs only: +- power-domains : Should contain a phandle to a PM domain provider node + and an args specifier containing the DCAN device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt +- clocks : CAN functional clock phandle. This property is as per the + binding, + Documentation/devicetree/bindings/clock/ti,sci-clk.txt + +Optional properties: +- syscon-raminit : Handle to system control region that contains the + RAMINIT register, register offset to the RAMINIT + register and the CAN instance number (0 offset). + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Example: + +Step1: SoC common .dtsi file + + dcan1: d_can@481d0000 { + compatible = "bosch,d_can"; + reg = <0x481d0000 0x2000>; + interrupts = <55>; + interrupt-parent = <&intc>; + status = "disabled"; + }; + +(or) + + dcan1: d_can@481d0000 { + compatible = "bosch,d_can"; + ti,hwmods = "d_can1"; + reg = <0x481d0000 0x2000>; + interrupts = <55>; + interrupt-parent = <&intc>; + status = "disabled"; + }; + +Step 2: board specific .dts file + + &dcan1 { + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/net/can/can-transceiver.txt b/Documentation/devicetree/bindings/net/can/can-transceiver.txt new file mode 100644 index 000000000..0011f53ff --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/can-transceiver.txt @@ -0,0 +1,24 @@ +Generic CAN transceiver Device Tree binding +------------------------------ + +CAN transceiver typically limits the max speed in standard CAN and CAN FD +modes. Typically these limitations are static and the transceivers themselves +provide no way to detect this limitation at runtime. For this situation, +the "can-transceiver" node can be used. + +Required Properties: + max-bitrate: a positive non 0 value that determines the max + speed that CAN/CAN-FD can run. Any other value + will be ignored. + +Examples: + +Based on Texas Instrument's TCAN1042HGV CAN Transceiver + +m_can0 { + .... + can-transceiver { + max-bitrate = <5000000>; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/net/can/cc770.txt b/Documentation/devicetree/bindings/net/can/cc770.txt new file mode 100644 index 000000000..77027bf64 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/cc770.txt @@ -0,0 +1,53 @@ +Memory mapped Bosch CC770 and Intel AN82527 CAN controller + +Note: The CC770 is a CAN controller from Bosch, which is 100% +compatible with the old AN82527 from Intel, but with "bugs" being fixed. + +Required properties: + +- compatible : should be "bosch,cc770" for the CC770 and "intc,82527" + for the AN82527. + +- reg : should specify the chip select, address offset and size required + to map the registers of the controller. The size is usually 0x80. + +- interrupts : property with a value describing the interrupt source + (number and sensitivity) required for the controller. + +Optional properties: + +- bosch,external-clock-frequency : frequency of the external oscillator + clock in Hz. Note that the internal clock frequency used by the + controller is half of that value. If not specified, a default + value of 16000000 (16 MHz) is used. + +- bosch,clock-out-frequency : slock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + +- bosch,slew-rate : slew rate of the CLKOUT signal. If not specified, + a resonable value will be calculated. + +- bosch,disconnect-rx0-input : see data sheet. + +- bosch,disconnect-rx1-input : see data sheet. + +- bosch,disconnect-tx1-output : see data sheet. + +- bosch,polarity-dominant : see data sheet. + +- bosch,divide-memory-clock : see data sheet. + +- bosch,iso-low-speed-mux : see data sheet. + +For further information, please have a look to the CC770 or AN82527. + +Examples: + +can@3,100 { + compatible = "bosch,cc770"; + reg = <3 0x100 0x80>; + interrupts = <2 0>; + interrupt-parent = <&mpic>; + bosch,external-clock-frequency = <16000000>; +}; diff --git a/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt new file mode 100644 index 000000000..bfc0c4336 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/fsl-flexcan.txt @@ -0,0 +1,35 @@ +Flexcan CAN controller on Freescale's ARM and PowerPC system-on-a-chip (SOC). + +Required properties: + +- compatible : Should be "fsl,<processor>-flexcan" + + An implementation should also claim any of the following compatibles + that it is fully backwards compatible with: + + - fsl,p1010-flexcan + +- reg : Offset and length of the register set for this device +- interrupts : Interrupt tuple for this device + +Optional properties: + +- clock-frequency : The oscillator frequency driving the flexcan device + +- xceiver-supply: Regulator that powers the CAN transceiver + +- big-endian: This means the registers of FlexCAN controller are big endian. + This is optional property.i.e. if this property is not present in + device tree node then controller is assumed to be little endian. + if this property is present then controller is assumed to be big + endian. + +Example: + + can@1c000 { + compatible = "fsl,p1010-flexcan"; + reg = <0x1c000 0x1000>; + interrupts = <48 0x2>; + interrupt-parent = <&mpic>; + clock-frequency = <200000000>; // filled in by bootloader + }; diff --git a/Documentation/devicetree/bindings/net/can/grcan.txt b/Documentation/devicetree/bindings/net/can/grcan.txt new file mode 100644 index 000000000..34ef3498f --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/grcan.txt @@ -0,0 +1,28 @@ +Aeroflex Gaisler GRCAN and GRHCAN CAN controllers. + +The GRCAN and CRHCAN CAN controllers are available in the GRLIB VHDL IP core +library. + +Note: These properties are built from the AMBA plug&play in a Leon SPARC system +(the ordinary environment for GRCAN and GRHCAN). There are no dts files for +sparc. + +Required properties: + +- name : Should be "GAISLER_GRCAN", "01_03d", "GAISLER_GRHCAN" or "01_034" + +- reg : Address and length of the register set for the device + +- freq : Frequency of the external oscillator clock in Hz (the frequency of + the amba bus in the ordinary case) + +- interrupts : Interrupt number for this device + +Optional properties: + +- systemid : If not present or if the value of the least significant 16 bits + of this 32-bit property is smaller than GRCAN_TXBUG_SAFE_GRLIB_VERSION + a bug workaround is activated. + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/net/can/holt_hi311x.txt b/Documentation/devicetree/bindings/net/can/holt_hi311x.txt new file mode 100644 index 000000000..3a9926f99 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/holt_hi311x.txt @@ -0,0 +1,23 @@ +* Holt HI-311X stand-alone CAN controller device tree bindings + +Required properties: + - compatible: Should be one of the following: + - "holt,hi3110" for HI-3110 + - reg: SPI chip select. + - clocks: The clock feeding the CAN controller. + - interrupts: Should contain IRQ line for the CAN controller. + +Optional properties: + - vdd-supply: Regulator that powers the CAN controller. + - xceiver-supply: Regulator that powers the CAN transceiver. + +Example: + can0: can@1 { + compatible = "holt,hi3110"; + reg = <1>; + clocks = <&clk32m>; + interrupt-parent = <&gpio4>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; + vdd-supply = <®5v0>; + xceiver-supply = <®5v0>; + }; diff --git a/Documentation/devicetree/bindings/net/can/ifi_canfd.txt b/Documentation/devicetree/bindings/net/can/ifi_canfd.txt new file mode 100644 index 000000000..20ea5c70a --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/ifi_canfd.txt @@ -0,0 +1,15 @@ +IFI CANFD controller +-------------------- + +Required properties: + - compatible: Should be "ifi,canfd-1.0" + - reg: Should contain CAN controller registers location and length + - interrupts: Should contain IRQ line for the CAN controller + +Example: + + canfd0: canfd@ff220000 { + compatible = "ifi,canfd-1.0"; + reg = <0xff220000 0x00001000>; + interrupts = <0 43 0>; + }; diff --git a/Documentation/devicetree/bindings/net/can/m_can.txt b/Documentation/devicetree/bindings/net/can/m_can.txt new file mode 100644 index 000000000..ed614383a --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/m_can.txt @@ -0,0 +1,75 @@ +Bosch MCAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "bosch,m_can" for M_CAN controllers +- reg : physical base address and size of the M_CAN + registers map and Message RAM +- reg-names : Should be "m_can" and "message_ram" +- interrupts : Should be the interrupt number of M_CAN interrupt + line 0 and line 1, could be same if sharing + the same interrupt. +- interrupt-names : Should contain "int0" and "int1" +- clocks : Clocks used by controller, should be host clock + and CAN clock. +- clock-names : Should contain "hclk" and "cclk" +- pinctrl-<n> : Pinctrl states as described in bindings/pinctrl/pinctrl-bindings.txt +- pinctrl-names : Names corresponding to the numbered pinctrl states +- bosch,mram-cfg : Message RAM configuration data. + Multiple M_CAN instances can share the same Message + RAM and each element(e.g Rx FIFO or Tx Buffer and etc) + number in Message RAM is also configurable, + so this property is telling driver how the shared or + private Message RAM are used by this M_CAN controller. + + The format should be as follows: + <offset sidf_elems xidf_elems rxf0_elems rxf1_elems + rxb_elems txe_elems txb_elems> + The 'offset' is an address offset of the Message RAM + where the following elements start from. This is + usually set to 0x0 if you're using a private Message + RAM. The remain cells are used to specify how many + elements are used for each FIFO/Buffer. + + M_CAN includes the following elements according to user manual: + 11-bit Filter 0-128 elements / 0-128 words + 29-bit Filter 0-64 elements / 0-128 words + Rx FIFO 0 0-64 elements / 0-1152 words + Rx FIFO 1 0-64 elements / 0-1152 words + Rx Buffers 0-64 elements / 0-1152 words + Tx Event FIFO 0-32 elements / 0-64 words + Tx Buffers 0-32 elements / 0-576 words + + Please refer to 2.4.1 Message RAM Configuration in + Bosch M_CAN user manual for details. + +Optional Subnode: +- can-transceiver : Can-transceiver subnode describing maximum speed + that can be used for CAN/CAN-FD modes. See + Documentation/devicetree/bindings/net/can/can-transceiver.txt + for details. +Example: +SoC dtsi: +m_can1: can@20e8000 { + compatible = "bosch,m_can"; + reg = <0x020e8000 0x4000>, <0x02298000 0x4000>; + reg-names = "m_can", "message_ram"; + interrupts = <0 114 0x04>, + <0 114 0x04>; + interrupt-names = "int0", "int1"; + clocks = <&clks IMX6SX_CLK_CANFD>, + <&clks IMX6SX_CLK_CANFD>; + clock-names = "hclk", "cclk"; + bosch,mram-cfg = <0x0 0 0 32 0 0 0 1>; +}; + +Board dts: +&m_can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_m_can1>; + status = "enabled"; + + can-transceiver { + max-bitrate = <5000000>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt b/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt new file mode 100644 index 000000000..5a0111d4d --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/microchip,mcp251x.txt @@ -0,0 +1,25 @@ +* Microchip MCP251X stand-alone CAN controller device tree bindings + +Required properties: + - compatible: Should be one of the following: + - "microchip,mcp2510" for MCP2510. + - "microchip,mcp2515" for MCP2515. + - "microchip,mcp25625" for MCP25625. + - reg: SPI chip select. + - clocks: The clock feeding the CAN controller. + - interrupts: Should contain IRQ line for the CAN controller. + +Optional properties: + - vdd-supply: Regulator that powers the CAN controller. + - xceiver-supply: Regulator that powers the CAN transceiver. + +Example: + can0: can@1 { + compatible = "microchip,mcp2515"; + reg = <1>; + clocks = <&clk24m>; + interrupt-parent = <&gpio4>; + interrupts = <13 0x2>; + vdd-supply = <®5v0>; + xceiver-supply = <®5v0>; + }; diff --git a/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt new file mode 100644 index 000000000..2fa4fcd38 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/mpc5xxx-mscan.txt @@ -0,0 +1,53 @@ +CAN Device Tree Bindings +------------------------ + +(c) 2006-2009 Secret Lab Technologies Ltd +Grant Likely <grant.likely@secretlab.ca> + +fsl,mpc5200-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock (XTAL) + "ref" is default in case this property is not + present. + +fsl,mpc5121-mscan nodes +----------------------- +In addition to the required compatible-, reg- and interrupt-properties, you can +also specify which clock source and divider shall be used for the controller: + +- fsl,mscan-clock-source : a string describing the clock source. Valid values + are: "ip" for ip bus clock + "ref" for reference clock + "sys" for system clock + If this property is not present, an optimal CAN + clock source and frequency based on the system + clock will be selected. If this is not possible, + the reference clock will be used. + +- fsl,mscan-clock-divider: for the reference and system clock, an additional + clock divider can be specified. By default, a + value of 1 is used. + +Note that the MPC5121 Rev. 1 processor is not supported. + +Examples: + can@1300 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <12 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1300 0x80>; + }; + + can@1380 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <13 0x8>; + interrupt-parent = <&ipic>; + reg = <0x1380 0x80>; + fsl,mscan-clock-source = "ref"; + fsl,mscan-clock-divider = <3>; + }; diff --git a/Documentation/devicetree/bindings/net/can/rcar_can.txt b/Documentation/devicetree/bindings/net/can/rcar_can.txt new file mode 100644 index 000000000..94a7f33ac --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/rcar_can.txt @@ -0,0 +1,68 @@ +Renesas R-Car CAN controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible: "renesas,can-r8a7743" if CAN controller is a part of R8A7743 SoC. + "renesas,can-r8a7745" if CAN controller is a part of R8A7745 SoC. + "renesas,can-r8a7778" if CAN controller is a part of R8A7778 SoC. + "renesas,can-r8a7779" if CAN controller is a part of R8A7779 SoC. + "renesas,can-r8a7790" if CAN controller is a part of R8A7790 SoC. + "renesas,can-r8a7791" if CAN controller is a part of R8A7791 SoC. + "renesas,can-r8a7792" if CAN controller is a part of R8A7792 SoC. + "renesas,can-r8a7793" if CAN controller is a part of R8A7793 SoC. + "renesas,can-r8a7794" if CAN controller is a part of R8A7794 SoC. + "renesas,can-r8a7795" if CAN controller is a part of R8A7795 SoC. + "renesas,can-r8a7796" if CAN controller is a part of R8A7796 SoC. + "renesas,rcar-gen1-can" for a generic R-Car Gen1 compatible device. + "renesas,rcar-gen2-can" for a generic R-Car Gen2 or RZ/G1 + compatible device. + "renesas,rcar-gen3-can" for a generic R-Car Gen3 compatible device. + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: physical base address and size of the R-Car CAN register map. +- interrupts: interrupt specifier for the sole interrupt. +- clocks: phandles and clock specifiers for 3 CAN clock inputs. +- clock-names: 3 clock input name strings: "clkp1", "clkp2", "can_clk". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must be "default". + +Required properties for "renesas,can-r8a7795" and "renesas,can-r8a7796" +compatible: +In R8A7795 and R8A7796 SoCs, "clkp2" can be CANFD clock. This is a div6 clock +and can be used by both CAN and CAN FD controller at the same time. It needs to +be scaled to maximum frequency if any of these controllers use it. This is done +using the below properties: + +- assigned-clocks: phandle of clkp2(CANFD) clock. +- assigned-clock-rates: maximum frequency of this clock. + +Optional properties: +- renesas,can-clock-select: R-Car CAN Clock Source Select. Valid values are: + <0x0> (default) : Peripheral clock (clkp1) + <0x1> : Peripheral clock (clkp2) + <0x3> : Externally input clock + +Example +------- + +SoC common .dtsi file: + + can0: can@e6e80000 { + compatible = "renesas,can-r8a7791", "renesas,rcar-gen2-can"; + reg = <0 0xe6e80000 0 0x1000>; + interrupts = <0 186 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_RCAN0>, + <&cpg_clocks R8A7791_CLK_RCAN>, <&can_clk>; + clock-names = "clkp1", "clkp2", "can_clk"; + status = "disabled"; + }; + +Board specific .dts file: + +&can0 { + pinctrl-0 = <&can0_pins>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/net/can/rcar_canfd.txt b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt new file mode 100644 index 000000000..ac71daa46 --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/rcar_canfd.txt @@ -0,0 +1,100 @@ +Renesas R-Car CAN FD controller Device Tree Bindings +---------------------------------------------------- + +Required properties: +- compatible: Must contain one or more of the following: + - "renesas,rcar-gen3-canfd" for R-Car Gen3 compatible controller. + - "renesas,r8a7795-canfd" for R8A7795 (R-Car H3) compatible controller. + - "renesas,r8a7796-canfd" for R8A7796 (R-Car M3-W) compatible controller. + - "renesas,r8a77970-canfd" for R8A77970 (R-Car V3M) compatible controller. + - "renesas,r8a77980-canfd" for R8A77980 (R-Car V3H) compatible controller. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first, followed by the + family-specific and/or generic versions. + +- reg: physical base address and size of the R-Car CAN FD register map. +- interrupts: interrupt specifiers for the Channel & Global interrupts +- clocks: phandles and clock specifiers for 3 clock inputs. +- clock-names: 3 clock input name strings: "fck", "canfd", "can_clk". +- pinctrl-0: pin control group to be used for this controller. +- pinctrl-names: must be "default". + +Required child nodes: +The controller supports two channels and each is represented as a child node. +The name of the child nodes are "channel0" and "channel1" respectively. Each +child node supports the "status" property only, which is used to +enable/disable the respective channel. + +Required properties for "renesas,r8a7795-canfd" and "renesas,r8a7796-canfd" +compatible: +In R8A7795 and R8A7796 SoCs, canfd clock is a div6 clock and can be used by both +CAN and CAN FD controller at the same time. It needs to be scaled to maximum +frequency if any of these controllers use it. This is done using the below +properties: + +- assigned-clocks: phandle of canfd clock. +- assigned-clock-rates: maximum frequency of this clock. + +Optional property: +The controller can operate in either CAN FD only mode (default) or +Classical CAN only mode. The mode is global to both the channels. In order to +enable the later, define the following optional property. + - renesas,no-can-fd: puts the controller in Classical CAN only mode. + +Example +------- + +SoC common .dtsi file: + + canfd: can@e66c0000 { + compatible = "renesas,r8a7795-canfd", + "renesas,rcar-gen3-canfd"; + reg = <0 0xe66c0000 0 0x8000>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 914>, + <&cpg CPG_CORE R8A7795_CLK_CANFD>, + <&can_clk>; + clock-names = "fck", "canfd", "can_clk"; + assigned-clocks = <&cpg CPG_CORE R8A7795_CLK_CANFD>; + assigned-clock-rates = <40000000>; + power-domains = <&cpg>; + status = "disabled"; + + channel0 { + status = "disabled"; + }; + + channel1 { + status = "disabled"; + }; + }; + +Board specific .dts file: + +E.g. below enables Channel 1 alone in the board in Classical CAN only mode. + +&canfd { + pinctrl-0 = <&canfd1_pins>; + pinctrl-names = "default"; + renesas,no-can-fd; + status = "okay"; + + channel1 { + status = "okay"; + }; +}; + +E.g. below enables Channel 0 alone in the board using External clock +as fCAN clock. + +&canfd { + pinctrl-0 = <&canfd0_pins &can_clk_pins>; + pinctrl-names = "default"; + status = "okay"; + + channel0 { + status = "okay"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/can/sja1000.txt b/Documentation/devicetree/bindings/net/can/sja1000.txt new file mode 100644 index 000000000..ac3160eca --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/sja1000.txt @@ -0,0 +1,58 @@ +Memory mapped SJA1000 CAN controller from NXP (formerly Philips) + +Required properties: + +- compatible : should be one of "nxp,sja1000", "technologic,sja1000". + +- reg : should specify the chip select, address offset and size required + to map the registers of the SJA1000. The size is usually 0x80. + +- interrupts: property with a value describing the interrupt source + (number and sensitivity) required for the SJA1000. + +Optional properties: + +- reg-io-width : Specify the size (in bytes) of the IO accesses that + should be performed on the device. Valid value is 1, 2 or 4. + This property is ignored for technologic version. + Default to 1 (8 bits). + +- nxp,external-clock-frequency : Frequency of the external oscillator + clock in Hz. Note that the internal clock frequency used by the + SJA1000 is half of that value. If not specified, a default value + of 16000000 (16 MHz) is used. + +- nxp,tx-output-mode : operation mode of the TX output control logic: + <0x0> : bi-phase output mode + <0x1> : normal output mode (default) + <0x2> : test output mode + <0x3> : clock output mode + +- nxp,tx-output-config : TX output pin configuration: + <0x01> : TX0 invert + <0x02> : TX0 pull-down (default) + <0x04> : TX0 pull-up + <0x06> : TX0 push-pull + <0x08> : TX1 invert + <0x10> : TX1 pull-down + <0x20> : TX1 pull-up + <0x30> : TX1 push-pull + +- nxp,clock-out-frequency : clock frequency in Hz on the CLKOUT pin. + If not specified or if the specified value is 0, the CLKOUT pin + will be disabled. + +- nxp,no-comparator-bypass : Allows to disable the CAN input comparator. + +For further information, please have a look to the SJA1000 data sheet. + +Examples: + +can@3,100 { + compatible = "nxp,sja1000"; + reg = <3 0x100 0x80>; + interrupts = <2 0>; + interrupt-parent = <&mpic>; + nxp,external-clock-frequency = <16000000>; +}; + diff --git a/Documentation/devicetree/bindings/net/can/sun4i_can.txt b/Documentation/devicetree/bindings/net/can/sun4i_can.txt new file mode 100644 index 000000000..f69845e6f --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/sun4i_can.txt @@ -0,0 +1,36 @@ +Allwinner A10/A20 CAN controller Device Tree Bindings +----------------------------------------------------- + +Required properties: +- compatible: "allwinner,sun4i-a10-can" +- reg: physical base address and size of the Allwinner A10/A20 CAN register map. +- interrupts: interrupt specifier for the sole interrupt. +- clock: phandle and clock specifier. + +Example +------- + +SoC common .dtsi file: + + can0_pins_a: can0@0 { + allwinner,pins = "PH20","PH21"; + allwinner,function = "can"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; +... + can0: can@1c2bc00 { + compatible = "allwinner,sun4i-a10-can"; + reg = <0x01c2bc00 0x400>; + interrupts = <0 26 4>; + clocks = <&apb1_gates 4>; + status = "disabled"; + }; + +Board specific .dts file: + + can0: can@1c2bc00 { + pinctrl-names = "default"; + pinctrl-0 = <&can0_pins_a>; + status = "okay"; + }; diff --git a/Documentation/devicetree/bindings/net/can/ti_hecc.txt b/Documentation/devicetree/bindings/net/can/ti_hecc.txt new file mode 100644 index 000000000..e0f0a7cfe --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/ti_hecc.txt @@ -0,0 +1,32 @@ +Texas Instruments High End CAN Controller (HECC) +================================================ + +This file provides information, what the device node +for the hecc interface contains. + +Required properties: +- compatible: "ti,am3517-hecc" +- reg: addresses and lengths of the register spaces for 'hecc', 'hecc-ram' + and 'mbx' +- reg-names :"hecc", "hecc-ram", "mbx" +- interrupts: interrupt mapping for the hecc interrupts sources +- clocks: clock phandles (see clock bindings for details) + +Optional properties: +- ti,use-hecc1int: if provided configures HECC to produce all interrupts + on HECC1INT interrupt line. By default HECC0INT interrupt + line will be used. +- xceiver-supply: regulator that powers the CAN transceiver + +Example: + +For am3517evm board: + hecc: can@5c050000 { + compatible = "ti,am3517-hecc"; + reg = <0x5c050000 0x80>, + <0x5c053000 0x180>, + <0x5c052000 0x200>; + reg-names = "hecc", "hecc-ram", "mbx"; + interrupts = <24>; + clocks = <&hecc_ck>; + }; diff --git a/Documentation/devicetree/bindings/net/can/xilinx_can.txt b/Documentation/devicetree/bindings/net/can/xilinx_can.txt new file mode 100644 index 000000000..060e2d46b --- /dev/null +++ b/Documentation/devicetree/bindings/net/can/xilinx_can.txt @@ -0,0 +1,60 @@ +Xilinx Axi CAN/Zynq CANPS controller Device Tree Bindings +--------------------------------------------------------- + +Required properties: +- compatible : Should be: + - "xlnx,zynq-can-1.0" for Zynq CAN controllers + - "xlnx,axi-can-1.00.a" for Axi CAN controllers + - "xlnx,canfd-1.0" for CAN FD controllers +- reg : Physical base address and size of the controller + registers map. +- interrupts : Property with a value describing the interrupt + number. +- clock-names : List of input clock names + - "can_clk", "pclk" (For CANPS), + - "can_clk", "s_axi_aclk" (For AXI CAN and CAN FD). + (See clock bindings for details). +- clocks : Clock phandles (see clock bindings for details). +- tx-fifo-depth : Can Tx fifo depth (Zynq, Axi CAN). +- rx-fifo-depth : Can Rx fifo depth (Zynq, Axi CAN, CAN FD in + sequential Rx mode). +- tx-mailbox-count : Can Tx mailbox buffer count (CAN FD). +- rx-mailbox-count : Can Rx mailbox buffer count (CAN FD in mailbox Rx + mode). + + +Example: + +For Zynq CANPS Dts file: + zynq_can_0: can@e0008000 { + compatible = "xlnx,zynq-can-1.0"; + clocks = <&clkc 19>, <&clkc 36>; + clock-names = "can_clk", "pclk"; + reg = <0xe0008000 0x1000>; + interrupts = <0 28 4>; + interrupt-parent = <&intc>; + tx-fifo-depth = <0x40>; + rx-fifo-depth = <0x40>; + }; +For Axi CAN Dts file: + axi_can_0: axi-can@40000000 { + compatible = "xlnx,axi-can-1.00.a"; + clocks = <&clkc 0>, <&clkc 1>; + clock-names = "can_clk","s_axi_aclk" ; + reg = <0x40000000 0x10000>; + interrupt-parent = <&intc>; + interrupts = <0 59 1>; + tx-fifo-depth = <0x40>; + rx-fifo-depth = <0x40>; + }; +For CAN FD Dts file: + canfd_0: canfd@40000000 { + compatible = "xlnx,canfd-1.0"; + clocks = <&clkc 0>, <&clkc 1>; + clock-names = "can_clk", "s_axi_aclk"; + reg = <0x40000000 0x2000>; + interrupt-parent = <&intc>; + interrupts = <0 59 1>; + tx-mailbox-count = <0x20>; + rx-fifo-depth = <0x20>; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-mdio.txt b/Documentation/devicetree/bindings/net/cavium-mdio.txt new file mode 100644 index 000000000..020df08b8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-mdio.txt @@ -0,0 +1,84 @@ +* System Management Interface (SMI) / MDIO + +Properties: +- compatible: One of: + + "cavium,octeon-3860-mdio": Compatibility with all cn3XXX, cn5XXX + and cn6XXX SOCs. + + "cavium,thunder-8890-mdio": Compatibility with all cn8XXX SOCs. + +- reg: The base address of the MDIO bus controller register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. MDIO addresses have no size component. + +Typically an MDIO bus might have several children. + +Example: + mdio@1180000001800 { + compatible = "cavium,octeon-3860-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0x00001800 0x0 0x40>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; + + +* System Management Interface (SMI) / MDIO Nexus + + Several mdio buses may be gathered as children of a single PCI + device, this PCI device is the nexus of the buses. + +Properties: + +- compatible: "cavium,thunder-8890-mdio-nexus"; + +- reg: The PCI device and function numbers of the nexus device. + +- #address-cells: Must be <2>. + +- #size-cells: Must be <2>. + +- ranges: As needed for mapping of the MDIO bus device registers. + +- assigned-addresses: As needed for mapping of the MDIO bus device registers. + +Example: + + mdio-nexus@1,3 { + compatible = "cavium,thunder-8890-mdio-nexus"; + #address-cells = <2>; + #size-cells = <2>; + reg = <0x0b00 0 0 0 0>; /* DEVFN = 0x0b (1:3) */ + assigned-addresses = <0x03000000 0x87e0 0x05000000 0x0 0x800000>; + ranges = <0x87e0 0x05000000 0x03000000 0x87e0 0x05000000 0x0 0x800000>; + + mdio0@87e0,05003800 { + compatible = "cavium,thunder-8890-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x87e0 0x05003800 0x0 0x30>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; + mdio0@87e0,05003880 { + compatible = "cavium,thunder-8890-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x87e0 0x05003880 0x0 0x30>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-mix.txt b/Documentation/devicetree/bindings/net/cavium-mix.txt new file mode 100644 index 000000000..8d7c30963 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-mix.txt @@ -0,0 +1,34 @@ +* MIX Ethernet controller. + +Properties: +- compatible: "cavium,octeon-5750-mix" + + Compatibility with all cn5XXX and cn6XXX SOCs populated with MIX + devices. + +- reg: The base addresses of four separate register banks. The first + bank contains the MIX registers. The second bank the corresponding + AGL registers. The third bank are the AGL registers shared by all + MIX devices present. The fourth bank is the AGL_PRT_CTL shared by + all MIX devices present. + +- cell-index: A single cell specifying which portion of the shared + register banks corresponds to this MIX device. + +- interrupts: Two interrupt specifiers. The first is the MIX + interrupt routing and the second the routing for the AGL interrupts. + +- phy-handle: Optional, see ethernet.txt file in the same directory. + +Example: + ethernet@1070000100800 { + compatible = "cavium,octeon-5750-mix"; + reg = <0x10700 0x00100800 0x0 0x100>, /* MIX */ + <0x11800 0xE0000800 0x0 0x300>, /* AGL */ + <0x11800 0xE0000400 0x0 0x400>, /* AGL_SHARED */ + <0x11800 0xE0002008 0x0 0x8>; /* AGL_PRT_CTL */ + cell-index = <1>; + interrupts = <1 18>, < 1 46>; + local-mac-address = [ 00 0f b7 10 63 54 ]; + phy-handle = <&phy1>; + }; diff --git a/Documentation/devicetree/bindings/net/cavium-pip.txt b/Documentation/devicetree/bindings/net/cavium-pip.txt new file mode 100644 index 000000000..e3b8fe717 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cavium-pip.txt @@ -0,0 +1,99 @@ +* PIP Ethernet nexus. + +The PIP Ethernet nexus can control several data packet input/output +devices. The devices have a two level grouping scheme. There may be +several interfaces, and each interface may have several ports. These +ports might be an individual Ethernet PHY. + + +Properties for the PIP nexus: +- compatible: "cavium,octeon-3860-pip" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The base address of the PIP's register bank. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. + +Properties for PIP interfaces which is a child the PIP nexus: +- compatible: "cavium,octeon-3860-pip-interface" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The interface number. + +- #address-cells: Must be <1>. + +- #size-cells: Must be <0>. + +Properties for PIP port which is a child the PIP interface: +- compatible: "cavium,octeon-3860-pip-port" + + Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs. + +- reg: The port number within the interface group. + +- phy-handle: Optional, see ethernet.txt file in the same directory. + +- rx-delay: Delay value for RGMII receive clock. Optional. Disabled if 0. + Value range is 1-31, and mapping to the actual delay varies depending on HW. + +- tx-delay: Delay value for RGMII transmit clock. Optional. Disabled if 0. + Value range is 1-31, and mapping to the actual delay varies depending on HW. + +Example: + + pip@11800a0000000 { + compatible = "cavium,octeon-3860-pip"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0xa0000000 0x0 0x2000>; + + interface@0 { + compatible = "cavium,octeon-3860-pip-interface"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; /* interface */ + + ethernet@0 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x0>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 60 ]; + phy-handle = <&phy2>; + }; + ethernet@1 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x1>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 61 ]; + phy-handle = <&phy3>; + }; + ethernet@2 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x2>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 62 ]; + phy-handle = <&phy4>; + }; + ethernet@3 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x3>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 63 ]; + phy-handle = <&phy5>; + }; + }; + + interface@1 { + compatible = "cavium,octeon-3860-pip-interface"; + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; /* interface */ + + ethernet@0 { + compatible = "cavium,octeon-3860-pip-port"; + reg = <0x0>; /* Port */ + local-mac-address = [ 00 0f b7 10 63 64 ]; + phy-handle = <&phy6>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/cirrus,cs89x0.txt b/Documentation/devicetree/bindings/net/cirrus,cs89x0.txt new file mode 100644 index 000000000..c070076ba --- /dev/null +++ b/Documentation/devicetree/bindings/net/cirrus,cs89x0.txt @@ -0,0 +1,13 @@ +* Cirrus Logic CS8900/CS8920 Network Controller + +Required properties: +- compatible : Should be "cirrus,cs8900" or "cirrus,cs8920". +- reg : Address and length of the IO space. +- interrupts : Should contain the controller interrupt line. + +Examples: + eth0: eth@10000000 { + compatible = "cirrus,cs8900"; + reg = <0x10000000 0x400>; + interrupts = <10>; + }; diff --git a/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.txt b/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.txt new file mode 100644 index 000000000..6c559981d --- /dev/null +++ b/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.txt @@ -0,0 +1,92 @@ +Cortina Systems Gemini Ethernet Controller +========================================== + +This ethernet controller is found in the Gemini SoC family: +StorLink SL3512 and SL3516, also known as Cortina Systems +CS3512 and CS3516. + +Required properties: +- compatible: must be "cortina,gemini-ethernet" +- reg: must contain the global registers and the V-bit and A-bit + memory areas, in total three register sets. +- syscon: a phandle to the system controller +- #address-cells: must be specified, must be <1> +- #size-cells: must be specified, must be <1> +- ranges: should be state like this giving a 1:1 address translation + for the subnodes + +The subnodes represents the two ethernet ports in this device. +They are not independent of each other since they share resources +in the parent node, and are thus children. + +Required subnodes: +- port0: contains the resources for ethernet port 0 +- port1: contains the resources for ethernet port 1 + +Required subnode properties: +- compatible: must be "cortina,gemini-ethernet-port" +- reg: must contain two register areas: the DMA/TOE memory and + the GMAC memory area of the port +- interrupts: should contain the interrupt line of the port. + this is nominally a level interrupt active high. +- resets: this must provide an SoC-integrated reset line for + the port. +- clocks: this should contain a handle to the PCLK clock for + clocking the silicon in this port +- clock-names: must be "PCLK" + +Optional subnode properties: +- phy-mode: see ethernet.txt +- phy-handle: see ethernet.txt + +Example: + +mdio-bus { + (...) + phy0: ethernet-phy@1 { + reg = <1>; + device_type = "ethernet-phy"; + }; + phy1: ethernet-phy@3 { + reg = <3>; + device_type = "ethernet-phy"; + }; +}; + + +ethernet@60000000 { + compatible = "cortina,gemini-ethernet"; + reg = <0x60000000 0x4000>, /* Global registers, queue */ + <0x60004000 0x2000>, /* V-bit */ + <0x60006000 0x2000>; /* A-bit */ + syscon = <&syscon>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gmac0: ethernet-port@0 { + compatible = "cortina,gemini-ethernet-port"; + reg = <0x60008000 0x2000>, /* Port 0 DMA/TOE */ + <0x6000a000 0x2000>; /* Port 0 GMAC */ + interrupt-parent = <&intcon>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH>; + resets = <&syscon GEMINI_RESET_GMAC0>; + clocks = <&syscon GEMINI_CLK_GATE_GMAC0>; + clock-names = "PCLK"; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + }; + + gmac1: ethernet-port@1 { + compatible = "cortina,gemini-ethernet-port"; + reg = <0x6000c000 0x2000>, /* Port 1 DMA/TOE */ + <0x6000e000 0x2000>; /* Port 1 GMAC */ + interrupt-parent = <&intcon>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + resets = <&syscon GEMINI_RESET_GMAC1>; + clocks = <&syscon GEMINI_CLK_GATE_GMAC1>; + clock-names = "PCLK"; + phy-mode = "rgmii"; + phy-handle = <&phy1>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/cortina.txt b/Documentation/devicetree/bindings/net/cortina.txt new file mode 100644 index 000000000..40d0bd984 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cortina.txt @@ -0,0 +1,21 @@ +Cortina Phy Driver Device Tree Bindings +--------------------------------------- + +CORTINA is a registered trademark of Cortina Systems, Inc. + +The driver supports the Cortina Electronic Dispersion Compensation (EDC) +devices, equipped with clock and data recovery (CDR) circuits. These +devices make use of registers that are not compatible with Clause 45 or +Clause 22, therefore they need to be described using the +"ethernet-phy-id" compatible. + +Since the driver only implements polling mode support, interrupts info +can be skipped. + +Example (CS4340 phy): + mdio { + cs4340_phy@10 { + compatible = "ethernet-phy-id13e5.1002"; + reg = <0x10>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt new file mode 100644 index 000000000..764c0c79b --- /dev/null +++ b/Documentation/devicetree/bindings/net/cpsw-phy-sel.txt @@ -0,0 +1,30 @@ +TI CPSW Phy mode Selection Device Tree Bindings +----------------------------------------------- + +Required properties: +- compatible : Should be "ti,am3352-cpsw-phy-sel" for am335x platform and + "ti,dra7xx-cpsw-phy-sel" for dra7xx platform + "ti,am43xx-cpsw-phy-sel" for am43xx platform +- reg : physical base address and size of the cpsw + registers map +- reg-names : names of the register map given in "reg" node + +Optional properties: +-rmii-clock-ext : If present, the driver will configure the RMII + interface to external clock usage + +Examples: + + phy_sel: cpsw-phy-sel@44e10650 { + compatible = "ti,am3352-cpsw-phy-sel"; + reg= <0x44e10650 0x4>; + reg-names = "gmii-sel"; + }; + +(or) + phy_sel: cpsw-phy-sel@44e10650 { + compatible = "ti,am3352-cpsw-phy-sel"; + reg= <0x44e10650 0x4>; + reg-names = "gmii-sel"; + rmii-clock-ext; + }; diff --git a/Documentation/devicetree/bindings/net/cpsw.txt b/Documentation/devicetree/bindings/net/cpsw.txt new file mode 100644 index 000000000..b3acebe08 --- /dev/null +++ b/Documentation/devicetree/bindings/net/cpsw.txt @@ -0,0 +1,124 @@ +TI SoC Ethernet Switch Controller Device Tree Bindings +------------------------------------------------------ + +Required properties: +- compatible : Should be one of the below:- + "ti,cpsw" for backward compatible + "ti,am335x-cpsw" for AM335x controllers + "ti,am4372-cpsw" for AM437x controllers + "ti,dra7-cpsw" for DRA7x controllers +- reg : physical base address and size of the cpsw + registers map +- interrupts : property with a value describing the interrupt + number +- cpdma_channels : Specifies number of channels in CPDMA +- ale_entries : Specifies No of entries ALE can hold +- bd_ram_size : Specifies internal descriptor RAM size +- mac_control : Specifies Default MAC control register content + for the specific platform +- slaves : Specifies number for slaves +- active_slave : Specifies the slave to use for time stamping, + ethtool and SIOCGMIIPHY +- cpsw-phy-sel : Specifies the phandle to the CPSW phy mode selection + device. See also cpsw-phy-sel.txt for it's binding. + Note that in legacy cases cpsw-phy-sel may be + a child device instead of a phandle. + +Optional properties: +- ti,hwmods : Must be "cpgmac0" +- dual_emac : Specifies Switch to act as Dual EMAC +- syscon : Phandle to the system control device node, which is + the control module device of the am33x +- mode-gpios : Should be added if one/multiple gpio lines are + required to be driven so that cpsw data lines + can be connected to the phy via selective mux. + For example in dra72x-evm, pcf gpio has to be + driven low so that cpsw slave 0 and phy data + lines are connected via mux. +- cpts_clock_mult : Numerator to convert input clock ticks into nanoseconds +- cpts_clock_shift : Denominator to convert input clock ticks into nanoseconds + Mult and shift will be calculated basing on CPTS + rftclk frequency if both cpts_clock_shift and + cpts_clock_mult properties are not provided. + +Slave Properties: +Required properties: +- phy-mode : See ethernet.txt file in the same directory + +Optional properties: +- dual_emac_res_vlan : Specifies VID to be used to segregate the ports +- mac-address : See ethernet.txt file in the same directory +- phy_id : Specifies slave phy id (deprecated, use phy-handle) +- phy-handle : See ethernet.txt file in the same directory + +Slave sub-nodes: +- fixed-link : See fixed-link.txt file in the same directory + +Note: Exactly one of phy_id, phy-handle, or fixed-link must be specified. + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples: + + mac: ethernet@4a100000 { + compatible = "ti,cpsw"; + reg = <0x4A100000 0x1000>; + interrupts = <55 0x4>; + interrupt-parent = <&intc>; + cpdma_channels = <8>; + ale_entries = <1024>; + bd_ram_size = <0x2000>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; + syscon = <&cm>; + cpsw-phy-sel = <&phy_sel>; + cpsw_emac0: slave@0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + cpsw_emac1: slave@1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + }; + +(or) + mac: ethernet@4a100000 { + compatible = "ti,cpsw"; + ti,hwmods = "cpgmac0"; + cpdma_channels = <8>; + ale_entries = <1024>; + bd_ram_size = <0x2000>; + rx_descs = <64>; + mac_control = <0x20>; + slaves = <2>; + active_slave = <0>; + cpts_clock_mult = <0x80000000>; + cpts_clock_shift = <29>; + syscon = <&cm>; + cpsw-phy-sel = <&phy_sel>; + cpsw_emac0: slave@0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + cpsw_emac1: slave@1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "rgmii-txid"; + /* Filled in by U-Boot */ + mac-address = [ 00 00 00 00 00 00 ]; + }; + }; diff --git a/Documentation/devicetree/bindings/net/davicom-dm9000.txt b/Documentation/devicetree/bindings/net/davicom-dm9000.txt new file mode 100644 index 000000000..64c159e9c --- /dev/null +++ b/Documentation/devicetree/bindings/net/davicom-dm9000.txt @@ -0,0 +1,27 @@ +Davicom DM9000 Fast Ethernet controller + +Required properties: +- compatible = "davicom,dm9000"; +- reg : physical addresses and sizes of registers, must contain 2 entries: + first entry : address register, + second entry : data register. +- interrupts : interrupt specifier specific to interrupt controller + +Optional properties: +- davicom,no-eeprom : Configuration EEPROM is not available +- davicom,ext-phy : Use external PHY +- reset-gpios : phandle of gpio that will be used to reset chip during probe +- vcc-supply : phandle of regulator that will be used to enable power to chip + +Example: + + ethernet@18000000 { + compatible = "davicom,dm9000"; + reg = <0x18000000 0x2 0x18000004 0x2>; + interrupt-parent = <&gpn>; + interrupts = <7 4>; + local-mac-address = [00 00 de ad be ef]; + davicom,no-eeprom; + reset-gpios = <&gpf 12 GPIO_ACTIVE_LOW>; + vcc-supply = <ð0_power>; + }; diff --git a/Documentation/devicetree/bindings/net/davinci-mdio.txt b/Documentation/devicetree/bindings/net/davinci-mdio.txt new file mode 100644 index 000000000..e6527de80 --- /dev/null +++ b/Documentation/devicetree/bindings/net/davinci-mdio.txt @@ -0,0 +1,36 @@ +TI SoC Davinci/Keystone2 MDIO Controller Device Tree Bindings +--------------------------------------------------- + +Required properties: +- compatible : Should be "ti,davinci_mdio" + and "ti,keystone_mdio" for Keystone 2 SoCs + and "ti,cpsw-mdio" for am335x, am472x, am57xx/dra7, dm814x SoCs + and "ti,am4372-mdio" for am472x SoC +- reg : physical base address and size of the davinci mdio + registers map +- bus_freq : Mdio Bus frequency + +Optional properties: +- ti,hwmods : Must be "davinci_mdio" + +Note: "ti,hwmods" field is used to fetch the base address and irq +resources from TI, omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples: + + mdio: davinci_mdio@4a101000 { + compatible = "ti,davinci_mdio"; + reg = <0x4A101000 0x1000>; + bus_freq = <1000000>; + }; + +(or) + + mdio: davinci_mdio@4a101000 { + compatible = "ti,davinci_mdio"; + ti,hwmods = "davinci_mdio"; + bus_freq = <1000000>; + }; diff --git a/Documentation/devicetree/bindings/net/davinci_emac.txt b/Documentation/devicetree/bindings/net/davinci_emac.txt new file mode 100644 index 000000000..24c5cdaba --- /dev/null +++ b/Documentation/devicetree/bindings/net/davinci_emac.txt @@ -0,0 +1,41 @@ +* Texas Instruments Davinci EMAC + +This file provides information, what the device node +for the davinci_emac interface contains. + +Required properties: +- compatible: "ti,davinci-dm6467-emac", "ti,am3517-emac" or + "ti,dm816-emac" +- reg: Offset and length of the register set for the device +- ti,davinci-ctrl-reg-offset: offset to control register +- ti,davinci-ctrl-mod-reg-offset: offset to control module register +- ti,davinci-ctrl-ram-offset: offset to control module ram +- ti,davinci-ctrl-ram-size: size of control module ram +- interrupts: interrupt mapping for the davinci emac interrupts sources: + 4 sources: <Receive Threshold Interrupt + Receive Interrupt + Transmit Interrupt + Miscellaneous Interrupt> + +Optional properties: +- phy-handle: See ethernet.txt file in the same directory. + If absent, davinci_emac driver defaults to 100/FULL. +- ti,davinci-rmii-en: 1 byte, 1 means use RMII +- ti,davinci-no-bd-ram: boolean, does EMAC have BD RAM? + +Example (enbw_cmc board): + eth0: emac@1e20000 { + compatible = "ti,davinci-dm6467-emac"; + reg = <0x220000 0x4000>; + ti,davinci-ctrl-reg-offset = <0x3000>; + ti,davinci-ctrl-mod-reg-offset = <0x2000>; + ti,davinci-ctrl-ram-offset = <0>; + ti,davinci-ctrl-ram-size = <0x2000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <33 + 34 + 35 + 36 + >; + interrupt-parent = <&intc>; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt new file mode 100644 index 000000000..1811e1972 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/b53.txt @@ -0,0 +1,109 @@ +Broadcom BCM53xx Ethernet switches +================================== + +Required properties: + +- compatible: For external switch chips, compatible string must be exactly one + of: "brcm,bcm5325" + "brcm,bcm53115" + "brcm,bcm53125" + "brcm,bcm53128" + "brcm,bcm5365" + "brcm,bcm5395" + "brcm,bcm5389" + "brcm,bcm5397" + "brcm,bcm5398" + + For the BCM11360 SoC, must be: + "brcm,bcm11360-srab" and the mandatory "brcm,cygnus-srab" string + + For the BCM5310x SoCs with an integrated switch, must be one of: + "brcm,bcm53010-srab" + "brcm,bcm53011-srab" + "brcm,bcm53012-srab" + "brcm,bcm53018-srab" + "brcm,bcm53019-srab" and the mandatory "brcm,bcm5301x-srab" string + + For the BCM5831X/BCM1140x SoCs with an integrated switch, must be one of: + "brcm,bcm11404-srab" + "brcm,bcm11407-srab" + "brcm,bcm11409-srab" + "brcm,bcm58310-srab" + "brcm,bcm58311-srab" + "brcm,bcm58313-srab" and the mandatory "brcm,omega-srab" string + + For the BCM585xx/586XX/88312 SoCs with an integrated switch, must be one of: + "brcm,bcm58522-srab" + "brcm,bcm58523-srab" + "brcm,bcm58525-srab" + "brcm,bcm58622-srab" + "brcm,bcm58623-srab" + "brcm,bcm58625-srab" + "brcm,bcm88312-srab" and the mandatory "brcm,nsp-srab string + + For the BCM63xx/33xx SoCs with an integrated switch, must be one of: + "brcm,bcm3384-switch" + "brcm,bcm6328-switch" + "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch" + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional +required and optional properties. + +Examples: + +Ethernet switch connected via MDIO to the host, CPU port wired to eth0: + + eth0: ethernet@10001000 { + compatible = "brcm,unimac"; + reg = <0x10001000 0x1000>; + + fixed-link { + speed = <1000>; + duplex-full; + }; + }; + + mdio0: mdio@10000000 { + compatible = "brcm,unimac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + switch0: ethernet-switch@30 { + compatible = "brcm,bcm53125"; + #address-cells = <1>; + #size-cells = <0>; + + ports { + port0@0 { + reg = <0>; + label = "lan1"; + }; + + port1@1 { + reg = <1>; + label = "lan2"; + }; + + port5@5 { + reg = <5>; + label = "cable-modem"; + fixed-link { + speed = <1000>; + duplex-full; + }; + phy-mode = "rgmii-txid"; + }; + + port8@8 { + reg = <8>; + label = "cpu"; + fixed-link { + speed = <1000>; + duplex-full; + }; + phy-mode = "rgmii-txid"; + ethernet = <ð0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/dsa.txt b/Documentation/devicetree/bindings/net/dsa/dsa.txt new file mode 100644 index 000000000..3ceeb8de1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/dsa.txt @@ -0,0 +1,408 @@ +Distributed Switch Architecture Device Tree Bindings +---------------------------------------------------- + +Two bindings exist, one of which has been deprecated due to +limitations. + +Current Binding +--------------- + +Switches are true Linux devices and can be probes by any means. Once +probed, they register to the DSA framework, passing a node +pointer. This node is expected to fulfil the following binding, and +may contain additional properties as required by the device it is +embedded within. + +Required properties: + +- ports : A container for child nodes representing switch ports. + +Optional properties: + +- dsa,member : A two element list indicates which DSA cluster, and position + within the cluster a switch takes. <0 0> is cluster 0, + switch 0. <0 1> is cluster 0, switch 1. <1 0> is cluster 1, + switch 0. A switch not part of any cluster (single device + hanging off a CPU port) must not specify this property + +The ports container has the following properties + +Required properties: + +- #address-cells : Must be 1 +- #size-cells : Must be 0 + +Each port children node must have the following mandatory properties: +- reg : Describes the port address in the switch + +An uplink/downlink port between switches in the cluster has the following +mandatory property: + +- link : Should be a list of phandles to other switch's DSA + port. This port is used as the outgoing port + towards the phandle ports. The full routing + information must be given, not just the one hop + routes to neighbouring switches. + +A CPU port has the following mandatory property: + +- ethernet : Should be a phandle to a valid Ethernet device node. + This host device is what the switch port is + connected to. + +A user port has the following optional property: + +- label : Describes the label associated with this port, which + will become the netdev name. + +Port child nodes may also contain the following optional standardised +properties, described in binding documents: + +- phy-handle : Phandle to a PHY on an MDIO bus. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- phy-mode : See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + +Example + +The following example shows three switches on three MDIO busses, +linked into one DSA cluster. + +&mdio1 { + #address-cells = <1>; + #size-cells = <0>; + + switch0: switch0@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + + dsa,member = <0 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + switch0port5: port@5 { + reg = <5>; + phy-mode = "rgmii-txid"; + link = <&switch1port6 + &switch2port9>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + port@6 { + reg = <6>; + ethernet = <&fec1>; + fixed-link { + speed = <100>; + full-duplex; + }; + }; + }; + }; +}; + +&mdio2 { + #address-cells = <1>; + #size-cells = <0>; + + switch1: switch1@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + + dsa,member = <0 1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan3"; + phy-handle = <&switch1phy0>; + }; + + port@1 { + reg = <1>; + label = "lan4"; + phy-handle = <&switch1phy1>; + }; + + port@2 { + reg = <2>; + label = "lan5"; + phy-handle = <&switch1phy2>; + }; + + switch1port5: port@5 { + reg = <5>; + link = <&switch2port9>; + phy-mode = "rgmii-txid"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + switch1port6: port@6 { + reg = <6>; + phy-mode = "rgmii-txid"; + link = <&switch0port5>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + }; + switch1phy1: switch1phy0@1 { + reg = <1>; + }; + switch1phy2: switch1phy0@2 { + reg = <2>; + }; + }; + }; +}; + +&mdio4 { + #address-cells = <1>; + #size-cells = <0>; + + switch2: switch2@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + + dsa,member = <0 2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan6"; + }; + + port@1 { + reg = <1>; + label = "lan7"; + }; + + port@2 { + reg = <2>; + label = "lan8"; + }; + + port@3 { + reg = <3>; + label = "optical3"; + fixed-link { + speed = <1000>; + full-duplex; + link-gpios = <&gpio6 2 + GPIO_ACTIVE_HIGH>; + }; + }; + + port@4 { + reg = <4>; + label = "optical4"; + fixed-link { + speed = <1000>; + full-duplex; + link-gpios = <&gpio6 3 + GPIO_ACTIVE_HIGH>; + }; + }; + + switch2port9: port@9 { + reg = <9>; + phy-mode = "rgmii-txid"; + link = <&switch1port5 + &switch0port5>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +Deprecated Binding +------------------ + +The deprecated binding makes use of a platform device to represent the +switches. The switches themselves are not Linux devices, and make use +of an MDIO bus for management. + +Required properties: +- compatible : Should be "marvell,dsa" +- #address-cells : Must be 2, first cell is the address on the MDIO bus + and second cell is the address in the switch tree. + Second cell is used only when cascading/chaining. +- #size-cells : Must be 0 +- dsa,ethernet : Should be a phandle to a valid Ethernet device node +- dsa,mii-bus : Should be a phandle to a valid MDIO bus device node + +Optional properties: +- interrupts : property with a value describing the switch + interrupt number (not supported by the driver) + +A DSA node can contain multiple switch chips which are therefore child nodes of +the parent DSA node. The maximum number of allowed child nodes is 4 +(DSA_MAX_SWITCHES). +Each of these switch child nodes should have the following required properties: + +- reg : Contains two fields. The first one describes the + address on the MII bus. The second is the switch + number that must be unique in cascaded configurations +- #address-cells : Must be 1 +- #size-cells : Must be 0 + +A switch child node has the following optional property: + +- eeprom-length : Set to the length of an EEPROM connected to the + switch. Must be set if the switch can not detect + the presence and/or size of a connected EEPROM, + otherwise optional. + +A switch may have multiple "port" children nodes + +Each port children node must have the following mandatory properties: +- reg : Describes the port address in the switch +- label : Describes the label associated with this port, special + labels are "cpu" to indicate a CPU port and "dsa" to + indicate an uplink/downlink port. + +Note that a port labelled "dsa" will imply checking for the uplink phandle +described below. + +Optional property: +- link : Should be a list of phandles to another switch's DSA port. + This property is only used when switches are being + chained/cascaded together. This port is used as outgoing port + towards the phandle port, which can be more than one hop away. + +- phy-handle : Phandle to a PHY on an external MDIO bus, not the + switch internal one. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- phy-mode : String representing the connection to the designated + PHY node specified by the 'phy-handle' property. See + Documentation/devicetree/bindings/net/ethernet.txt + for details. + +- mii-bus : Should be a phandle to a valid MDIO bus device node. + This mii-bus will be used in preference to the + global dsa,mii-bus defined above, for this switch. + +Optional subnodes: +- fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + +Example: + + dsa@0 { + compatible = "marvell,dsa"; + #address-cells = <2>; + #size-cells = <0>; + + interrupts = <10>; + dsa,ethernet = <ðernet0>; + dsa,mii-bus = <&mii_bus0>; + + switch@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <16 0>; /* MDIO address 16, switch 0 in tree */ + + port@0 { + reg = <0>; + label = "lan1"; + phy-handle = <&phy0>; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + }; + + switch0port6: port@6 { + reg = <6>; + label = "dsa"; + link = <&switch1port0 + &switch2port0>; + }; + }; + + switch@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <17 1>; /* MDIO address 17, switch 1 in tree */ + mii-bus = <&mii_bus1>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + + switch1port0: port@0 { + reg = <0>; + label = "dsa"; + link = <&switch0port6>; + }; + switch1port1: port@1 { + reg = <1>; + label = "dsa"; + link = <&switch2port1>; + }; + }; + + switch@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <18 2>; /* MDIO address 18, switch 2 in tree */ + mii-bus = <&mii_bus1>; + + switch2port0: port@0 { + reg = <0>; + label = "dsa"; + link = <&switch1port1 + &switch0port6>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/ksz.txt b/Documentation/devicetree/bindings/net/dsa/ksz.txt new file mode 100644 index 000000000..ac145b885 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/ksz.txt @@ -0,0 +1,72 @@ +Microchip KSZ Series Ethernet switches +================================== + +Required properties: + +- compatible: For external switch chips, compatible string must be exactly one + of the following: + - "microchip,ksz9477" + - "microchip,ksz9897" + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional +required and optional properties. + +Examples: + +Ethernet switch connected via SPI to the host, CPU port wired to eth0: + + eth0: ethernet@10001000 { + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + + spi1: spi@f8008000 { + pinctrl-0 = <&pinctrl_spi_ksz>; + cs-gpios = <&pioC 25 0>; + id = <1>; + + ksz9477: ksz9477@0 { + compatible = "microchip,ksz9477"; + reg = <0>; + + spi-max-frequency = <44000000>; + spi-cpha; + spi-cpol; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + port@4 { + reg = <4>; + label = "lan5"; + }; + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <ð0>; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/lan9303.txt b/Documentation/devicetree/bindings/net/dsa/lan9303.txt new file mode 100644 index 000000000..464d6bf87 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/lan9303.txt @@ -0,0 +1,102 @@ +SMSC/MicroChip LAN9303 three port ethernet switch +------------------------------------------------- + +Required properties: + +- compatible: should be + - "smsc,lan9303-i2c" for I2C managed mode + or + - "smsc,lan9303-mdio" for mdio managed mode + +Optional properties: + +- reset-gpios: GPIO to be used to reset the whole device +- reset-duration: reset duration in milliseconds, defaults to 200 ms + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. The CPU port of this switch is always port 0. + +Note: always use 'reg = <0/1/2>;' for the three DSA ports, even if the device is +configured to use 1/2/3 instead. This hardware configuration will be +auto-detected and mapped accordingly. + +Example: + +I2C managed mode: + + master: masterdevice@X { + + fixed-link { /* RMII fixed link to LAN9303 */ + speed = <100>; + full-duplex; + }; + }; + + switch: switch@a { + compatible = "smsc,lan9303-i2c"; + reg = <0xa>; + reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; + reset-duration = <200>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { /* RMII fixed link to master */ + reg = <0>; + label = "cpu"; + ethernet = <&master>; + }; + + port@1 { /* external port 1 */ + reg = <1>; + label = "lan1"; + }; + + port@2 { /* external port 2 */ + reg = <2>; + label = "lan2"; + }; + }; + }; + +MDIO managed mode: + + master: masterdevice@X { + phy-handle = <&switch>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + switch: switch-phy@0 { + compatible = "smsc,lan9303-mdio"; + reg = <0>; + reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; + reset-duration = <100>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&master>; + }; + + port@1 { /* external port 1 */ + reg = <1>; + label = "lan1"; + }; + + port@2 { /* external port 2 */ + reg = <2>; + label = "lan2"; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt new file mode 100644 index 000000000..feb007af1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt @@ -0,0 +1,106 @@ +Marvell DSA Switch Device Tree Bindings +--------------------------------------- + +WARNING: This binding is currently unstable. Do not program it into a +FLASH never to be changed again. Once this binding is stable, this +warning will be removed. + +If you need a stable binding, use the old dsa.txt binding. + +Marvell Switches are MDIO devices. The following properties should be +placed as a child node of an mdio device. + +The properties described here are those specific to Marvell devices. +Additional required and optional properties can be found in dsa.txt. + +The compatibility string is used only to find an identification register, +which is at a different MDIO base address in different switch families. +- "marvell,mv88e6085" : Switch has base address 0x10. Use with models: + 6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165, + 6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321, + 6341, 6350, 6351, 6352 +- "marvell,mv88e6190" : Switch has base address 0x00. Use with models: + 6190, 6190X, 6191, 6290, 6390, 6390X + +Required properties: +- compatible : Should be one of "marvell,mv88e6085" or + "marvell,mv88e6190" as indicated above +- reg : Address on the MII bus for the switch. + +Optional properties: + +- reset-gpios : Should be a gpio specifier for a reset line +- interrupts : Interrupt from the switch +- interrupt-controller : Indicates the switch is itself an interrupt + controller. This is used for the PHY interrupts. +#interrupt-cells = <2> : Controller uses two cells, number and flag +- eeprom-length : Set to the length of an EEPROM connected to the + switch. Must be set if the switch can not detect + the presence and/or size of a connected EEPROM, + otherwise optional. +- mdio : Container of PHY and devices on the switches MDIO + bus. +- mdio? : Container of PHYs and devices on the external MDIO + bus. The node must contains a compatible string of + "marvell,mv88e6xxx-mdio-external" + +Example: + + mdio { + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + switch0: switch@0 { + compatible = "marvell,mv88e6085"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + interrupt-parent = <&switch0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + }; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + + switch0: switch@0 { + compatible = "marvell,mv88e6390"; + reg = <0>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + switch1phy0: switch1phy0@0 { + reg = <0>; + interrupt-parent = <&switch0>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + mdio1 { + compatible = "marvell,mv88e6xxx-mdio-external"; + #address-cells = <1>; + #size-cells = <0>; + switch1phy9: switch1phy0@9 { + reg = <9>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt new file mode 100644 index 000000000..aa3527f71 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/mt7530.txt @@ -0,0 +1,92 @@ +Mediatek MT7530 Ethernet switch +================================ + +Required properties: + +- compatible: Must be compatible = "mediatek,mt7530"; +- #address-cells: Must be 1. +- #size-cells: Must be 0. +- mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part + on multi-chip module belong to MT7623A has or the remotely standalone + chip as the function MT7623N reference board provided for. +- core-supply: Phandle to the regulator node necessary for the core power. +- io-supply: Phandle to the regulator node necessary for the I/O power. + See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt + for details for the regulator setup on these boards. + +If the property mediatek,mcm isn't defined, following property is required + +- reset-gpios: Should be a gpio specifier for a reset line. + +Else, following properties are required + +- resets : Phandle pointing to the system reset controller with + line index for the ethsys. +- reset-names : Should be set to "mcm". + +Required properties for the child nodes within ports container: + +- reg: Port address described must be 6 for CPU port and from 0 to 5 for + user ports. +- phy-mode: String, must be either "trgmii" or "rgmii" for port labeled + "cpu". + +See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional +required, optional properties and how the integrated switch subnodes must +be specified. + +Example: + + &mdio0 { + switch@0 { + compatible = "mediatek,mt7530"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + reset-gpios = <&pio 33 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.txt b/Documentation/devicetree/bindings/net/dsa/qca8k.txt new file mode 100644 index 000000000..bbcb255c3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/qca8k.txt @@ -0,0 +1,110 @@ +* Qualcomm Atheros QCA8xxx switch family + +Required properties: + +- compatible: should be one of: + "qca,qca8334" + "qca,qca8337" + +- #size-cells: must be 0 +- #address-cells: must be 1 + +Subnodes: + +The integrated switch subnode should be specified according to the binding +described in dsa/dsa.txt. As the QCA8K switches do not have a N:N mapping of +port and PHY id, each subnode describing a port needs to have a valid phandle +referencing the internal PHY connected to it. The CPU port of this switch is +always port 0. + +A CPU port node has the following optional node: + +- fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + +For QCA8K the 'fixed-link' sub-node supports only the following properties: + +- 'speed' (integer, mandatory), to indicate the link speed. Accepted + values are 10, 100 and 1000 +- 'full-duplex' (boolean, optional), to indicate that full duplex is + used. When absent, half duplex is assumed. + +Example: + + + &mdio0 { + phy_port1: phy@0 { + reg = <0>; + }; + + phy_port2: phy@1 { + reg = <1>; + }; + + phy_port3: phy@2 { + reg = <2>; + }; + + phy_port4: phy@3 { + reg = <3>; + }; + + phy_port5: phy@4 { + reg = <4>; + }; + + switch0@0 { + compatible = "qca,qca8337"; + #address-cells = <1>; + #size-cells = <0>; + + reg = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + fixed-link { + speed = 1000; + full-duplex; + }; + }; + + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy_port1>; + }; + + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy_port2>; + }; + + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy_port3>; + }; + + port@4 { + reg = <4>; + label = "lan4"; + phy-handle = <&phy_port4>; + }; + + port@5 { + reg = <5>; + label = "wan"; + phy-handle = <&phy_port5>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt new file mode 100644 index 000000000..b6ae8541b --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt @@ -0,0 +1,153 @@ +Realtek SMI-based Switches +========================== + +The SMI "Simple Management Interface" is a two-wire protocol using +bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does +not use the MDIO protocol. This binding defines how to specify the +SMI-based Realtek devices. + +Required properties: + +- compatible: must be exactly one of: + "realtek,rtl8366" + "realtek,rtl8366rb" (4+1 ports) + "realtek,rtl8366s" (4+1 ports) + "realtek,rtl8367" + "realtek,rtl8367b" + "realtek,rtl8368s" (8 port) + "realtek,rtl8369" + "realtek,rtl8370" (8 port) + +Required properties: +- mdc-gpios: GPIO line for the MDC clock line. +- mdio-gpios: GPIO line for the MDIO data line. +- reset-gpios: GPIO line for the reset signal. + +Optional properties: +- realtek,disable-leds: if the LED drivers are not used in the + hardware design this will disable them so they are not turned on + and wasting power. + +Required subnodes: + +- interrupt-controller + + This defines an interrupt controller with an IRQ line (typically + a GPIO) that will demultiplex and handle the interrupt from the single + interrupt line coming out of one of the SMI-based chips. It most + importantly provides link up/down interrupts to the PHY blocks inside + the ASIC. + +Required properties of interrupt-controller: + +- interrupt: parent interrupt, see interrupt-controller/interrupts.txt +- interrupt-controller: see interrupt-controller/interrupts.txt +- #address-cells: should be <0> +- #interrupt-cells: should be <1> + +- mdio + + This defines the internal MDIO bus of the SMI device, mostly for the + purpose of being able to hook the interrupts to the right PHY and + the right PHY to the corresponding port. + +Required properties of mdio: + +- compatible: should be set to "realtek,smi-mdio" for all SMI devices + +See net/mdio.txt for additional MDIO bus properties. + +See net/dsa/dsa.txt for a list of additional required and optional properties +and subnodes of DSA switches. + +Examples: + +switch { + compatible = "realtek,rtl8366rb"; + /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ + mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + + switch_intc: interrupt-controller { + /* GPIO 15 provides the interrupt */ + interrupt-parent = <&gpio0>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&phy0>; + }; + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy1>; + }; + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy2>; + }; + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy3>; + }; + port@4 { + reg = <4>; + label = "wan"; + phy-handle = <&phy4>; + }; + port@5 { + reg = <5>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + + mdio { + compatible = "realtek,smi-mdio", "dsa-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc>; + interrupts = <0>; + }; + phy1: phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc>; + interrupts = <1>; + }; + phy2: phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc>; + interrupts = <2>; + }; + phy3: phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc>; + interrupts = <3>; + }; + phy4: phy@4 { + reg = <4>; + interrupt-parent = <&switch_intc>; + interrupts = <12>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt new file mode 100644 index 000000000..ed4710c40 --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/vitesse,vsc73xx.txt @@ -0,0 +1,81 @@ +Vitesse VSC73xx Switches +======================== + +This defines device tree bindings for the Vitesse VSC73xx switch chips. +The Vitesse company has been acquired by Microsemi and Microsemi in turn +acquired by Microchip but retains this vendor branding. + +The currently supported switch chips are: +Vitesse VSC7385 SparX-G5 5+1-port Integrated Gigabit Ethernet Switch +Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch +Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch +Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch + +The device tree node is an SPI device so it must reside inside a SPI bus +device tree node, see spi/spi-bus.txt + +Required properties: + +- compatible: must be exactly one of: + "vitesse,vsc7385" + "vitesse,vsc7388" + "vitesse,vsc7395" + "vitesse,vsc7398" +- gpio-controller: indicates that this switch is also a GPIO controller, + see gpio/gpio.txt +- #gpio-cells: this must be set to <2> and indicates that we are a twocell + GPIO controller, see gpio/gpio.txt + +Optional properties: + +- reset-gpios: a handle to a GPIO line that can issue reset of the chip. + It should be tagged as active low. + +Required subnodes: + +See net/dsa/dsa.txt for a list of additional required and optional properties +and subnodes of DSA switches. + +Examples: + +switch@0 { + compatible = "vitesse,vsc7395"; + reg = <0>; + /* Specified for 2.5 MHz or below */ + spi-max-frequency = <2500000>; + gpio-controller; + #gpio-cells = <2>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + port@1 { + reg = <1>; + label = "lan2"; + }; + port@2 { + reg = <2>; + label = "lan3"; + }; + port@3 { + reg = <3>; + label = "lan4"; + }; + vsc: port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac1>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt new file mode 100644 index 000000000..5bb3a18cc --- /dev/null +++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt @@ -0,0 +1,200 @@ +* Allwinner sun8i GMAC ethernet controller + +This device is a platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +Required properties: +- compatible: must be one of the following string: + "allwinner,sun8i-a83t-emac" + "allwinner,sun8i-h3-emac" + "allwinner,sun8i-r40-gmac" + "allwinner,sun8i-v3s-emac" + "allwinner,sun50i-a64-emac" +- reg: address and length of the register for the device. +- interrupts: interrupt for the device +- interrupt-names: must be "macirq" +- clocks: A phandle to the reference clock for this device +- clock-names: must be "stmmaceth" +- resets: A phandle to the reset control for this device +- reset-names: must be "stmmaceth" +- phy-mode: See ethernet.txt +- phy-handle: See ethernet.txt +- syscon: A phandle to the device containing the EMAC or GMAC clock register + +Optional properties: +- allwinner,tx-delay-ps: TX clock delay chain value in ps. + Range is 0-700. Default is 0. + Unavailable for allwinner,sun8i-r40-gmac +- allwinner,rx-delay-ps: RX clock delay chain value in ps. + Range is 0-3100. Default is 0. + Range is 0-700 for allwinner,sun8i-r40-gmac +Both delay properties need to be a multiple of 100. They control the +clock delay for external RGMII PHY. They do not apply to the internal +PHY or external non-RGMII PHYs. + +Optional properties for the following compatibles: + - "allwinner,sun8i-h3-emac", + - "allwinner,sun8i-v3s-emac": +- allwinner,leds-active-low: EPHY LEDs are active low + +Required child node of emac: +- mdio bus node: should be named mdio with compatible "snps,dwmac-mdio" + +Required properties of the mdio node: +- #address-cells: shall be 1 +- #size-cells: shall be 0 + +The device node referenced by "phy" or "phy-handle" must be a child node +of the mdio node. See phy.txt for the generic PHY bindings. + +The following compatibles require that the emac node have a mdio-mux child +node called "mdio-mux": + - "allwinner,sun8i-h3-emac" + - "allwinner,sun8i-v3s-emac": +Required properties for the mdio-mux node: + - compatible = "allwinner,sun8i-h3-mdio-mux" + - mdio-parent-bus: a phandle to EMAC mdio + - one child mdio for the integrated mdio with the compatible + "allwinner,sun8i-h3-mdio-internal" + - one child mdio for the external mdio if present (V3s have none) +Required properties for the mdio-mux children node: + - reg: 1 for internal MDIO bus, 2 for external MDIO bus + +The following compatibles require a PHY node representing the integrated +PHY, under the integrated MDIO bus node if an mdio-mux node is used: + - "allwinner,sun8i-h3-emac", + - "allwinner,sun8i-v3s-emac": + +Additional information regarding generic multiplexer properties can be found +at Documentation/devicetree/bindings/net/mdio-mux.txt + +Required properties of the integrated phy node: +- clocks: a phandle to the reference clock for the EPHY +- resets: a phandle to the reset control for the EPHY +- Must be a child of the integrated mdio + +Example with integrated PHY: +emac: ethernet@1c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + + phy-handle = <&int_mii_phy>; + phy-mode = "mii"; + allwinner,leds-active-low; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + + mdio-mux { + compatible = "mdio-mux", "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + + mdio-parent-bus = <&mdio>; + + int_mdio: mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + int_mii_phy: ethernet-phy@1 { + reg = <1>; + clocks = <&ccu CLK_BUS_EPHY>; + resets = <&ccu RST_BUS_EPHY>; + phy-is-integrated; + }; + }; + ext_mdio: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + }; + }; +}; + +Example with external PHY: +emac: ethernet@1c0b000 { + compatible = "allwinner,sun8i-h3-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + allwinner,leds-active-low; + + mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + }; + + mdio-mux { + compatible = "allwinner,sun8i-h3-mdio-mux"; + #address-cells = <1>; + #size-cells = <0>; + + mdio-parent-bus = <&mdio>; + + int_mdio: mdio@1 { + compatible = "allwinner,sun8i-h3-mdio-internal"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + int_mii_phy: ethernet-phy@1 { + reg = <1>; + clocks = <&ccu CLK_BUS_EPHY>; + resets = <&ccu RST_BUS_EPHY>; + }; + }; + ext_mdio: mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + ext_rgmii_phy: ethernet-phy@1 { + reg = <1>; + }; + }: + }; +}; + +Example with SoC without integrated PHY + +emac: ethernet@1c0b000 { + compatible = "allwinner,sun8i-a83t-emac"; + syscon = <&syscon>; + reg = <0x01c0b000 0x104>; + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + resets = <&ccu RST_BUS_EMAC>; + reset-names = "stmmaceth"; + clocks = <&ccu CLK_BUS_EMAC>; + clock-names = "stmmaceth"; + + phy-handle = <&ext_rgmii_phy>; + phy-mode = "rgmii"; + + mdio: mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + ext_rgmii_phy: ethernet-phy@1 { + reg = <1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/emac_rockchip.txt b/Documentation/devicetree/bindings/net/emac_rockchip.txt new file mode 100644 index 000000000..05bd7dafc --- /dev/null +++ b/Documentation/devicetree/bindings/net/emac_rockchip.txt @@ -0,0 +1,52 @@ +* ARC EMAC 10/100 Ethernet platform driver for Rockchip RK3036/RK3066/RK3188 SoCs + +Required properties: +- compatible: should be "rockchip,<name>-emac" + "rockchip,rk3036-emac": found on RK3036 SoCs + "rockchip,rk3066-emac": found on RK3066 SoCs + "rockchip,rk3188-emac": found on RK3188 SoCs +- reg: Address and length of the register set for the device +- interrupts: Should contain the EMAC interrupts +- rockchip,grf: phandle to the syscon grf used to control speed and mode + for emac. +- phy: see ethernet.txt file in the same directory. +- phy-mode: see ethernet.txt file in the same directory. + +Optional properties: +- phy-supply: phandle to a regulator if the PHY needs one + +Clock handling: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Shall be "hclk" for the host clock needed to calculate and set + polling period of EMAC and "macref" for the reference clock needed to transfer + data to and from the phy. + +Child nodes of the driver are the individual PHY devices connected to the +MDIO bus. They must have a "reg" property given the PHY address on the MDIO bus. + +Examples: + +ethernet@10204000 { + compatible = "rockchip,rk3188-emac"; + reg = <0xc0fc2000 0x3c>; + interrupts = <6>; + mac-address = [ 00 11 22 33 44 55 ]; + + clocks = <&cru HCLK_EMAC>, <&cru SCLK_MAC>; + clock-names = "hclk", "macref"; + + pinctrl-names = "default"; + pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>; + + rockchip,grf = <&grf>; + + phy = <&phy0>; + phy-mode = "rmii"; + phy-supply = <&vcc_rmii>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/ethernet.txt b/Documentation/devicetree/bindings/net/ethernet.txt new file mode 100644 index 000000000..cfc376bc9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ethernet.txt @@ -0,0 +1,66 @@ +The following properties are common to the Ethernet controllers: + +NOTE: All 'phy*' properties documented below are Ethernet specific. For the +generic PHY 'phys' property, see +Documentation/devicetree/bindings/phy/phy-bindings.txt. + +- local-mac-address: array of 6 bytes, specifies the MAC address that was + assigned to the network device; +- mac-address: array of 6 bytes, specifies the MAC address that was last used by + the boot program; should be used in cases where the MAC address assigned to + the device by the boot program is different from the "local-mac-address" + property; +- nvmem-cells: phandle, reference to an nvmem node for the MAC address; +- nvmem-cell-names: string, should be "mac-address" if nvmem is to be used; +- max-speed: number, specifies maximum speed in Mbit/s supported by the device; +- max-frame-size: number, maximum transfer unit (IEEE defined MTU), rather than + the maximum frame size (there's contradiction in the Devicetree + Specification). +- phy-mode: string, operation mode of the PHY interface. This is now a de-facto + standard property; supported values are: + * "internal" + * "mii" + * "gmii" + * "sgmii" + * "qsgmii" + * "tbi" + * "rev-mii" + * "rmii" + * "rgmii" (RX and TX delays are added by the MAC when required) + * "rgmii-id" (RGMII with internal RX and TX delays provided by the PHY, the + MAC should not add the RX or TX delays in this case) + * "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC + should not add an RX delay in this case) + * "rgmii-txid" (RGMII with internal TX delay provided by the PHY, the MAC + should not add an TX delay in this case) + * "rtbi" + * "smii" + * "xgmii" + * "trgmii" + * "2000base-x", + * "2500base-x", + * "rxaui" + * "xaui" + * "10gbase-kr" (10GBASE-KR, XFI, SFI) +- phy-connection-type: the same as "phy-mode" property but described in the + Devicetree Specification; +- phy-handle: phandle, specifies a reference to a node representing a PHY + device; this property is described in the Devicetree Specification and so + preferred; +- phy: the same as "phy-handle" property, not recommended for new bindings. +- phy-device: the same as "phy-handle" property, not recommended for new + bindings. +- rx-fifo-depth: the size of the controller's receive fifo in bytes. This + is used for components that can have configurable receive fifo sizes, + and is useful for determining certain configuration settings such as + flow control thresholds. +- tx-fifo-depth: the size of the controller's transmit fifo in bytes. This + is used for components that can have configurable fifo sizes. +- managed: string, specifies the PHY management type. Supported values are: + "auto", "in-band-status". "auto" is the default, it usess MDIO for + management if fixed-link is not specified. + +Child nodes of the Ethernet controller are typically the individual PHY devices +connected via the MDIO bus (sometimes the MDIO bus controller is separate). +They are described in the phy.txt file in this same directory. +For non-MDIO PHY management see fixed-link.txt. diff --git a/Documentation/devicetree/bindings/net/ezchip_enet.txt b/Documentation/devicetree/bindings/net/ezchip_enet.txt new file mode 100644 index 000000000..4e29b2b82 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ezchip_enet.txt @@ -0,0 +1,15 @@ +* EZchip NPS Management Ethernet port driver + +Required properties: +- compatible: Should be "ezchip,nps-mgt-enet" +- reg: Address and length of the register set for the device +- interrupts: Should contain the ENET interrupt + +Examples: + + ethernet@f0003000 { + compatible = "ezchip,nps-mgt-enet"; + reg = <0xf0003000 0x44>; + interrupts = <7>; + mac-address = [ 00 11 22 33 44 55 ]; + }; diff --git a/Documentation/devicetree/bindings/net/faraday,ftmac.txt b/Documentation/devicetree/bindings/net/faraday,ftmac.txt new file mode 100644 index 000000000..be4f55e23 --- /dev/null +++ b/Documentation/devicetree/bindings/net/faraday,ftmac.txt @@ -0,0 +1,24 @@ +Faraday Ethernet Controller + +Required properties: + +- compatible : Must contain "faraday,ftmac", as well as one of + the SoC specific identifiers: + "andestech,atmac100" + "moxa,moxart-mac" +- reg : Should contain register location and length +- interrupts : Should contain the mac interrupt number + +Example: + + mac0: mac@90900000 { + compatible = "moxa,moxart-mac"; + reg = <0x90900000 0x100>; + interrupts = <25 0>; + }; + + mac1: mac@92000000 { + compatible = "moxa,moxart-mac"; + reg = <0x92000000 0x100>; + interrupts = <27 0>; + }; diff --git a/Documentation/devicetree/bindings/net/fixed-link.txt b/Documentation/devicetree/bindings/net/fixed-link.txt new file mode 100644 index 000000000..ec5d889fe --- /dev/null +++ b/Documentation/devicetree/bindings/net/fixed-link.txt @@ -0,0 +1,54 @@ +Fixed link Device Tree binding +------------------------------ + +Some Ethernet MACs have a "fixed link", and are not connected to a +normal MDIO-managed PHY device. For those situations, a Device Tree +binding allows to describe a "fixed link". + +Such a fixed link situation is described by creating a 'fixed-link' +sub-node of the Ethernet MAC device node, with the following +properties: + +* 'speed' (integer, mandatory), to indicate the link speed. Accepted + values are 10, 100 and 1000 +* 'full-duplex' (boolean, optional), to indicate that full duplex is + used. When absent, half duplex is assumed. +* 'pause' (boolean, optional), to indicate that pause should be + enabled. +* 'asym-pause' (boolean, optional), to indicate that asym_pause should + be enabled. +* 'link-gpios' ('gpio-list', optional), to indicate if a gpio can be read + to determine if the link is up. + +Old, deprecated 'fixed-link' binding: + +* A 'fixed-link' property in the Ethernet MAC node, with 5 cells, of the + form <a b c d e> with the following accepted values: + - a: emulated PHY ID, choose any but but unique to the all specified + fixed-links, from 0 to 31 + - b: duplex configuration: 0 for half duplex, 1 for full duplex + - c: link speed in Mbits/sec, accepted values are: 10, 100 and 1000 + - d: pause configuration: 0 for no pause, 1 for pause + - e: asymmetric pause configuration: 0 for no asymmetric pause, 1 for + asymmetric pause + +Examples: + +ethernet@0 { + ... + fixed-link { + speed = <1000>; + full-duplex; + }; + ... +}; + +ethernet@1 { + ... + fixed-link { + speed = <1000>; + pause; + link-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + ... +}; diff --git a/Documentation/devicetree/bindings/net/fsl-fec.txt b/Documentation/devicetree/bindings/net/fsl-fec.txt new file mode 100644 index 000000000..2d41fb96c --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-fec.txt @@ -0,0 +1,85 @@ +* Freescale Fast Ethernet Controller (FEC) + +Required properties: +- compatible : Should be "fsl,<soc>-fec" +- reg : Address and length of the register set for the device +- interrupts : Should contain fec interrupt +- phy-mode : See ethernet.txt file in the same directory + +Optional properties: +- phy-reset-gpios : Should specify the gpio for phy reset +- phy-reset-duration : Reset duration in milliseconds. Should present + only if property "phy-reset-gpios" is available. Missing the property + will have the duration be 1 millisecond. Numbers greater than 1000 are + invalid and 1 millisecond will be used instead. +- phy-reset-active-high : If present then the reset sequence using the GPIO + specified in the "phy-reset-gpios" property is reversed (H=reset state, + L=operation state). +- phy-reset-post-delay : Post reset delay in milliseconds. If present then + a delay of phy-reset-post-delay milliseconds will be observed after the + phy-reset-gpios has been toggled. Can be omitted thus no delay is + observed. Delay is in range of 1ms to 1000ms. Other delays are invalid. +- phy-supply : regulator that powers the Ethernet PHY. +- phy-handle : phandle to the PHY device connected to this device. +- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. + Use instead of phy-handle. +- fsl,num-tx-queues : The property is valid for enet-avb IP, which supports + hw multi queues. Should specify the tx queue number, otherwise set tx queue + number to 1. +- fsl,num-rx-queues : The property is valid for enet-avb IP, which supports + hw multi queues. Should specify the rx queue number, otherwise set rx queue + number to 1. +- fsl,magic-packet : If present, indicates that the hardware supports waking + up via magic packet. +- fsl,err006687-workaround-present: If present indicates that the system has + the hardware workaround for ERR006687 applied and does not need a software + workaround. + -interrupt-names: names of the interrupts listed in interrupts property in + the same order. The defaults if not specified are + __Number of interrupts__ __Default__ + 1 "int0" + 2 "int0", "pps" + 3 "int0", "int1", "int2" + 4 "int0", "int1", "int2", "pps" + The order may be changed as long as they correspond to the interrupts + property. Currently, only i.mx7 uses "int1" and "int2". They correspond to + tx/rx queues 1 and 2. "int0" will be used for queue 0 and ENET_MII interrupts. + For imx6sx, "int0" handles all 3 queues and ENET_MII. "pps" is for the pulse + per second interrupt associated with 1588 precision time protocol(PTP). + + +Optional subnodes: +- mdio : specifies the mdio bus in the FEC, used as a container for phy nodes + according to phy.txt in the same directory + +Example: + +ethernet@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */ + local-mac-address = [00 04 9F 01 1B B9]; + phy-supply = <®_fec_supply>; +}; + +Example with phy specified: + +ethernet@83fec000 { + compatible = "fsl,imx51-fec", "fsl,imx27-fec"; + reg = <0x83fec000 0x4000>; + interrupts = <87>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; /* GPIO2_14 */ + local-mac-address = [00 04 9F 01 1B B9]; + phy-supply = <®_fec_supply>; + phy-handle = <ðphy>; + mdio { + ethphy: ethernet-phy@6 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <6>; + max-speed = <100>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/fsl-fman.txt b/Documentation/devicetree/bindings/net/fsl-fman.txt new file mode 100644 index 000000000..1316f0aec --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-fman.txt @@ -0,0 +1,641 @@ +============================================================================= +Freescale Frame Manager Device Bindings + +CONTENTS + - FMan Node + - FMan Port Node + - FMan MURAM Node + - FMan dTSEC/XGEC/mEMAC Node + - FMan IEEE 1588 Node + - FMan MDIO Node + - Example + +============================================================================= +FMan Node + +DESCRIPTION + +Due to the fact that the FMan is an aggregation of sub-engines (ports, MACs, +etc.) the FMan node will have child nodes for each of them. + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: Must include "fsl,fman" + FMan version can be determined via FM_IP_REV_1 register in the + FMan block. The offset is 0xc4 from the beginning of the + Frame Processing Manager memory map (0xc3000 from the + beginning of the FMan node). + +- cell-index + Usage: required + Value type: <u32> + Definition: Specifies the index of the FMan unit. + + The cell-index value may be used by the SoC, to identify the + FMan unit in the SoC memory map. In the table below, + there's a description of the cell-index use in each SoC: + + - P1023: + register[bit] FMan unit cell-index + ============================================================ + DEVDISR[1] 1 0 + + - P2041, P3041, P4080 P5020, P5040: + register[bit] FMan unit cell-index + ============================================================ + DCFG_DEVDISR2[6] 1 0 + DCFG_DEVDISR2[14] 2 1 + (Second FM available only in P4080 and P5040) + + - B4860, T1040, T2080, T4240: + register[bit] FMan unit cell-index + ============================================================ + DCFG_CCSR_DEVDISR2[24] 1 0 + DCFG_CCSR_DEVDISR2[25] 2 1 + (Second FM available only in T4240) + + DEVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in + the specific SoC "Device Configuration/Pin Control" Memory + Map. + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. Specifies the offset of the + following configuration registers: + - BMI configuration registers. + - QMI configuration registers. + - DMA configuration registers. + - FPM configuration registers. + - FMan controller configuration registers. + +- ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. + +- clocks + Usage: required + Value type: <prop-encoded-array> + Definition: phandle for the fman input clock. + +- clock-names + usage: required + Value type: <stringlist> + Definition: "fmanclk" for the fman input clock. + +- interrupts + Usage: required + Value type: <prop-encoded-array> + Definition: A pair of IRQs are specified in this property. + The first element is associated with the event interrupts and + the second element is associated with the error interrupts. + +- fsl,qman-channel-range + Usage: required + Value type: <prop-encoded-array> + Definition: Specifies the range of the available dedicated + channels in the FMan. The first cell specifies the beginning + of the range and the second cell specifies the number of + channels. + Further information available at: + "Work Queue (WQ) Channel Assignments in the QMan" section + in DPAA Reference Manual. + +- fsl,qman +- fsl,bman + Usage: required + Definition: See soc/fsl/qman.txt and soc/fsl/bman.txt + +- fsl,erratum-a050385 + Usage: optional + Value type: boolean + Definition: A boolean property. Indicates the presence of the + erratum A050385 which indicates that DMA transactions that are + split can result in a FMan lock. + +============================================================================= +FMan MURAM Node + +DESCRIPTION + +FMan Internal memory - shared between all the FMan modules. +It contains data structures that are common and written to or read by +the modules. +FMan internal memory is split into the following parts: + Packet buffering (Tx/Rx FIFOs) + Frames internal context + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: Must include "fsl,fman-muram" + +- ranges + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. + Specifies the multi-user memory offset and the size within + the FMan. + +EXAMPLE + +muram@0 { + compatible = "fsl,fman-muram"; + ranges = <0 0x000000 0x28000>; +}; + +============================================================================= +FMan Port Node + +DESCRIPTION + +The Frame Manager (FMan) supports several types of hardware ports: + Ethernet receiver (RX) + Ethernet transmitter (TX) + Offline/Host command (O/H) + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: A standard property. + Must include one of the following: + - "fsl,fman-v2-port-oh" for FManV2 OH ports + - "fsl,fman-v2-port-rx" for FManV2 RX ports + - "fsl,fman-v2-port-tx" for FManV2 TX ports + - "fsl,fman-v3-port-oh" for FManV3 OH ports + - "fsl,fman-v3-port-rx" for FManV3 RX ports + - "fsl,fman-v3-port-tx" for FManV3 TX ports + +- cell-index + Usage: required + Value type: <u32> + Definition: Specifies the hardware port id. + Each hardware port on the FMan has its own hardware PortID. + Super set of all hardware Port IDs available at FMan Reference + Manual under "FMan Hardware Ports in Freescale Devices" table. + + Each hardware port is assigned a 4KB, port-specific page in + the FMan hardware port memory region (which is part of the + FMan memory map). The first 4 KB in the FMan hardware ports + memory region is used for what are called common registers. + The subsequent 63 4KB pages are allocated to the hardware + ports. + The page of a specific port is determined by the cell-index. + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: There is one reg region describing the port + configuration registers. + +- fsl,fman-10g-port + Usage: optional + Value type: boolean + Definition: The default port rate is 1G. + If this property exists, the port is s 10G port. + +- fsl,fman-best-effort-port + Usage: optional + Value type: boolean + Definition: Can be defined only if 10G-support is set. + This property marks a best-effort 10G port (10G port that + may not be capable of line rate). + +EXAMPLE + +port@a8000 { + cell-index = <0x28>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xa8000 0x1000>; +}; + +port@88000 { + cell-index = <0x8>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x88000 0x1000>; +}; + +port@81000 { + cell-index = <0x1>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x81000 0x1000>; +}; + +============================================================================= +FMan dTSEC/XGEC/mEMAC Node + +DESCRIPTION + +mEMAC/dTSEC/XGEC are the Ethernet network interfaces + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: A standard property. + Must include one of the following: + - "fsl,fman-dtsec" for dTSEC MAC + - "fsl,fman-xgec" for XGEC MAC + - "fsl,fman-memac" for mEMAC MAC + +- cell-index + Usage: required + Value type: <u32> + Definition: Specifies the MAC id. + + The cell-index value may be used by the FMan or the SoC, to + identify the MAC unit in the FMan (or SoC) memory map. + In the tables below there's a description of the cell-index + use, there are two tables, one describes the use of cell-index + by the FMan, the second describes the use by the SoC: + + 1. FMan Registers + + FManV2: + register[bit] MAC cell-index + ============================================================ + FM_EPI[16] XGEC 8 + FM_EPI[16+n] dTSECn n-1 + FM_NPI[11+n] dTSECn n-1 + n = 1,..,5 + + FManV3: + register[bit] MAC cell-index + ============================================================ + FM_EPI[16+n] mEMACn n-1 + FM_EPI[25] mEMAC10 9 + + FM_NPI[11+n] mEMACn n-1 + FM_NPI[10] mEMAC10 9 + FM_NPI[11] mEMAC9 8 + n = 1,..8 + + FM_EPI and FM_NPI are located in the FMan memory map. + + 2. SoC registers: + + - P2041, P3041, P4080 P5020, P5040: + register[bit] FMan MAC cell + Unit index + ============================================================ + DCFG_DEVDISR2[7] 1 XGEC 8 + DCFG_DEVDISR2[7+n] 1 dTSECn n-1 + DCFG_DEVDISR2[15] 2 XGEC 8 + DCFG_DEVDISR2[15+n] 2 dTSECn n-1 + n = 1,..5 + + - T1040, T2080, T4240, B4860: + register[bit] FMan MAC cell + Unit index + ============================================================ + DCFG_CCSR_DEVDISR2[n-1] 1 mEMACn n-1 + DCFG_CCSR_DEVDISR2[11+n] 2 mEMACn n-1 + n = 1,..6,9,10 + + EVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in + the specific SoC "Device Configuration/Pin Control" Memory + Map. + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. + +- fsl,fman-ports + Usage: required + Value type: <prop-encoded-array> + Definition: An array of two phandles - the first references is + the FMan RX port and the second is the TX port used by this + MAC. + +- ptp-timer + Usage required + Value type: <phandle> + Definition: A phandle for 1EEE1588 timer. + +- pcsphy-handle + Usage required for "fsl,fman-memac" MACs + Value type: <phandle> + Definition: A phandle for pcsphy. + +- tbi-handle + Usage required for "fsl,fman-dtsec" MACs + Value type: <phandle> + Definition: A phandle for tbiphy. + +EXAMPLE + +fman1_tx28: port@a8000 { + cell-index = <0x28>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xa8000 0x1000>; +}; + +fman1_rx8: port@88000 { + cell-index = <0x8>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x88000 0x1000>; +}; + +ptp-timer: ptp_timer@fe000 { + compatible = "fsl,fman-ptp-timer"; + reg = <0xfe000 0x1000>; +}; + +ethernet@e0000 { + compatible = "fsl,fman-dtsec"; + cell-index = <0>; + reg = <0xe0000 0x1000>; + fsl,fman-ports = <&fman1_rx8 &fman1_tx28>; + ptp-timer = <&ptp-timer>; + tbi-handle = <&tbi0>; +}; + +============================================================================ +FMan IEEE 1588 Node + +Refer to Documentation/devicetree/bindings/ptp/ptp-qoriq.txt + +============================================================================= +FMan MDIO Node + +DESCRIPTION + +The MDIO is a bus to which the PHY devices are connected. + +PROPERTIES + +- compatible + Usage: required + Value type: <stringlist> + Definition: A standard property. + Must include "fsl,fman-mdio" for 1 Gb/s MDIO from FMan v2. + Must include "fsl,fman-xmdio" for 10 Gb/s MDIO from FMan v2. + Must include "fsl,fman-memac-mdio" for 1/10 Gb/s MDIO from + FMan v3. + +- reg + Usage: required + Value type: <prop-encoded-array> + Definition: A standard property. + +- bus-frequency + Usage: optional + Value type: <u32> + Definition: Specifies the external MDIO bus clock speed to + be used, if different from the standard 2.5 MHz. + This may be due to the standard speed being unsupported (e.g. + due to a hardware problem), or to advertise that all relevant + components in the system support a faster speed. + +- interrupts + Usage: required for external MDIO + Value type: <prop-encoded-array> + Definition: Event interrupt of external MDIO controller. + +- fsl,fman-internal-mdio + Usage: required for internal MDIO + Value type: boolean + Definition: Fman has internal MDIO for internal PCS(Physical + Coding Sublayer) PHYs and external MDIO for external PHYs. + The settings and programming routines for internal/external + MDIO are different. Must be included for internal MDIO. + +For internal PHY device on internal mdio bus, a PHY node should be created. +See the definition of the PHY node in booting-without-of.txt for an +example of how to define a PHY (Internal PHY has no interrupt line). +- For "fsl,fman-mdio" compatible internal mdio bus, the PHY is TBI PHY. +- For "fsl,fman-memac-mdio" compatible internal mdio bus, the PHY is PCS PHY, + PCS PHY addr must be '0'. + +EXAMPLE + +Example for FMan v2 external MDIO: + +mdio@f1000 { + compatible = "fsl,fman-xmdio"; + reg = <0xf1000 0x1000>; + interrupts = <101 2 0 0>; +}; + +Example for FMan v2 internal MDIO: + +mdio@e3120 { + compatible = "fsl,fman-mdio"; + reg = <0xe3120 0xee0>; + fsl,fman-internal-mdio; + + tbi1: tbi-phy@8 { + reg = <0x8>; + device_type = "tbi-phy"; + }; +}; + +Example for FMan v3 internal MDIO: + +mdio@f1000 { + compatible = "fsl,fman-memac-mdio"; + reg = <0xf1000 0x1000>; + fsl,fman-internal-mdio; + + pcsphy6: ethernet-phy@0 { + reg = <0x0>; + }; +}; + +============================================================================= +Example + +fman@400000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <1>; + compatible = "fsl,fman" + ranges = <0 0x400000 0x100000>; + reg = <0x400000 0x100000>; + clocks = <&fman_clk>; + clock-names = "fmanclk"; + interrupts = < + 96 2 0 0 + 16 2 1 1>; + fsl,qman-channel-range = <0x40 0xc>; + + muram@0 { + compatible = "fsl,fman-muram"; + reg = <0x0 0x28000>; + }; + + port@81000 { + cell-index = <1>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x81000 0x1000>; + }; + + port@82000 { + cell-index = <2>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x82000 0x1000>; + }; + + port@83000 { + cell-index = <3>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x83000 0x1000>; + }; + + port@84000 { + cell-index = <4>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x84000 0x1000>; + }; + + port@85000 { + cell-index = <5>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x85000 0x1000>; + }; + + port@86000 { + cell-index = <6>; + compatible = "fsl,fman-v2-port-oh"; + reg = <0x86000 0x1000>; + }; + + fman1_rx_0x8: port@88000 { + cell-index = <0x8>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x88000 0x1000>; + }; + + fman1_rx_0x9: port@89000 { + cell-index = <0x9>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x89000 0x1000>; + }; + + fman1_rx_0xa: port@8a000 { + cell-index = <0xa>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x8a000 0x1000>; + }; + + fman1_rx_0xb: port@8b000 { + cell-index = <0xb>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x8b000 0x1000>; + }; + + fman1_rx_0xc: port@8c000 { + cell-index = <0xc>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x8c000 0x1000>; + }; + + fman1_rx_0x10: port@90000 { + cell-index = <0x10>; + compatible = "fsl,fman-v2-port-rx"; + reg = <0x90000 0x1000>; + }; + + fman1_tx_0x28: port@a8000 { + cell-index = <0x28>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xa8000 0x1000>; + }; + + fman1_tx_0x29: port@a9000 { + cell-index = <0x29>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xa9000 0x1000>; + }; + + fman1_tx_0x2a: port@aa000 { + cell-index = <0x2a>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xaa000 0x1000>; + }; + + fman1_tx_0x2b: port@ab000 { + cell-index = <0x2b>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xab000 0x1000>; + }; + + fman1_tx_0x2c: port@ac0000 { + cell-index = <0x2c>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xac000 0x1000>; + }; + + fman1_tx_0x30: port@b0000 { + cell-index = <0x30>; + compatible = "fsl,fman-v2-port-tx"; + reg = <0xb0000 0x1000>; + }; + + ethernet@e0000 { + compatible = "fsl,fman-dtsec"; + cell-index = <0>; + reg = <0xe0000 0x1000>; + fsl,fman-ports = <&fman1_rx_0x8 &fman1_tx_0x28>; + tbi-handle = <&tbi5>; + }; + + ethernet@e2000 { + compatible = "fsl,fman-dtsec"; + cell-index = <1>; + reg = <0xe2000 0x1000>; + fsl,fman-ports = <&fman1_rx_0x9 &fman1_tx_0x29>; + tbi-handle = <&tbi6>; + }; + + ethernet@e4000 { + compatible = "fsl,fman-dtsec"; + cell-index = <2>; + reg = <0xe4000 0x1000>; + fsl,fman-ports = <&fman1_rx_0xa &fman1_tx_0x2a>; + tbi-handle = <&tbi7>; + }; + + ethernet@e6000 { + compatible = "fsl,fman-dtsec"; + cell-index = <3>; + reg = <0xe6000 0x1000>; + fsl,fman-ports = <&fman1_rx_0xb &fman1_tx_0x2b>; + tbi-handle = <&tbi8>; + }; + + ethernet@e8000 { + compatible = "fsl,fman-dtsec"; + cell-index = <4>; + reg = <0xf0000 0x1000>; + fsl,fman-ports = <&fman1_rx_0xc &fman1_tx_0x2c>; + tbi-handle = <&tbi9>; + + ethernet@f0000 { + cell-index = <8>; + compatible = "fsl,fman-xgec"; + reg = <0xf0000 0x1000>; + fsl,fman-ports = <&fman1_rx_0x10 &fman1_tx_0x30>; + }; + + ptp-timer@fe000 { + compatible = "fsl,fman-ptp-timer"; + reg = <0xfe000 0x1000>; + }; + + mdio@f1000 { + compatible = "fsl,fman-xmdio"; + reg = <0xf1000 0x1000>; + interrupts = <101 2 0 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt new file mode 100644 index 000000000..047bdf7bd --- /dev/null +++ b/Documentation/devicetree/bindings/net/fsl-tsec-phy.txt @@ -0,0 +1,89 @@ +* MDIO IO device + +The MDIO is a bus to which the PHY devices are connected. For each +device that exists on this bus, a child node should be created. See +the definition of the PHY node in booting-without-of.txt for an example +of how to define a PHY. + +Required properties: + - reg : Offset and length of the register set for the device, and optionally + the offset and length of the TBIPA register (TBI PHY address + register). If TBIPA register is not specified, the driver will + attempt to infer it from the register set specified (your mileage may + vary). + - compatible : Should define the compatible device type for the + mdio. Currently supported strings/devices are: + - "fsl,gianfar-tbi" + - "fsl,gianfar-mdio" + - "fsl,etsec2-tbi" + - "fsl,etsec2-mdio" + - "fsl,ucc-mdio" + - "fsl,fman-mdio" + When device_type is "mdio", the following strings are also considered: + - "gianfar" + - "ucc_geth_phy" + +Example: + + mdio@24520 { + reg = <24520 20>; + compatible = "fsl,gianfar-mdio"; + + ethernet-phy@0 { + ...... + }; + }; + +* TBI Internal MDIO bus + +As of this writing, every tsec is associated with an internal TBI PHY. +This PHY is accessed through the local MDIO bus. These buses are defined +similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi". +The TBI PHYs underneath them are similar to normal PHYs, but the reg property +is considered instructive, rather than descriptive. The reg property should +be chosen so it doesn't interfere with other PHYs on the bus. + +* Gianfar-compatible ethernet nodes + +Properties: + + - device_type : Should be "network" + - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" + - compatible : Should be "gianfar" + - reg : Offset and length of the register set for the device + - interrupts : For FEC devices, the first interrupt is the device's + interrupt. For TSEC and eTSEC devices, the first interrupt is + transmit, the second is receive, and the third is error. + - phy-handle : See ethernet.txt file in the same directory. + - fixed-link : See fixed-link.txt in the same directory. + - phy-connection-type : See ethernet.txt file in the same directory. + This property is only really needed if the connection is of type + "rgmii-id", as all other connection types are detected by hardware. + - fsl,magic-packet : If present, indicates that the hardware supports + waking up via magic packet. + - fsl,wake-on-filer : If present, indicates that the hardware supports + waking up by Filer General Purpose Interrupt (FGPI) asserted on the + Rx int line. This is an advanced power management capability allowing + certain packet types (user) defined by filer rules to wake up the system. + - bd-stash : If present, indicates that the hardware supports stashing + buffer descriptors in the L2. + - rx-stash-len : Denotes the number of bytes of a received buffer to stash + in the L2. + - rx-stash-idx : Denotes the index of the first byte from the received + buffer to stash in the L2. + +Example: + ethernet@24000 { + device_type = "network"; + model = "TSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + local-mac-address = [ 00 E0 0C 00 73 00 ]; + interrupts = <29 2 30 2 34 2>; + interrupt-parent = <&mpic>; + phy-handle = <&phy0> + }; + +* Gianfar PTP clock nodes + +Refer to Documentation/devicetree/bindings/ptp/ptp-qoriq.txt diff --git a/Documentation/devicetree/bindings/net/ftgmac100.txt b/Documentation/devicetree/bindings/net/ftgmac100.txt new file mode 100644 index 000000000..72e7aaf72 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ftgmac100.txt @@ -0,0 +1,34 @@ +* Faraday Technology FTGMAC100 gigabit ethernet controller + +Required properties: +- compatible: "faraday,ftgmac100" + + Must also contain one of these if used as part of an Aspeed AST2400 + or 2500 family SoC as they have some subtle tweaks to the + implementation: + + - "aspeed,ast2400-mac" + - "aspeed,ast2500-mac" + +- reg: Address and length of the register set for the device +- interrupts: Should contain ethernet controller interrupt + +Optional properties: +- phy-mode: See ethernet.txt file in the same directory. If the property is + absent, "rgmii" is assumed. Supported values are "rgmii*" and "rmii" for + aspeed parts. Other (unknown) parts will accept any value. +- use-ncsi: Use the NC-SI stack instead of an MDIO PHY. Currently assumes + rmii (100bT) but kept as a separate property in case NC-SI grows support + for a gigabit link. +- no-hw-checksum: Used to disable HW checksum support. Here for backward + compatibility as the driver now should have correct defaults based on + the SoC. + +Example: + + mac0: ethernet@1e660000 { + compatible = "aspeed,ast2500-mac", "faraday,ftgmac100"; + reg = <0x1e660000 0x180>; + interrupts = <2>; + use-ncsi; + }; diff --git a/Documentation/devicetree/bindings/net/gpmc-eth.txt b/Documentation/devicetree/bindings/net/gpmc-eth.txt new file mode 100644 index 000000000..f7da3d73c --- /dev/null +++ b/Documentation/devicetree/bindings/net/gpmc-eth.txt @@ -0,0 +1,97 @@ +Device tree bindings for Ethernet chip connected to TI GPMC + +Besides being used to interface with external memory devices, the +General-Purpose Memory Controller can be used to connect Pseudo-SRAM devices +such as ethernet controllers to processors using the TI GPMC as a data bus. + +Ethernet controllers connected to TI GPMC are represented as child nodes of +the GPMC controller with an "ethernet" name. + +All timing relevant properties as well as generic GPMC child properties are +explained in a separate documents. Please refer to +Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt + +For the properties relevant to the ethernet controller connected to the GPMC +refer to the binding documentation of the device. For example, the documentation +for the SMSC 911x is Documentation/devicetree/bindings/net/smsc911x.txt + +Child nodes need to specify the GPMC bus address width using the "bank-width" +property but is possible that an ethernet controller also has a property to +specify the I/O registers address width. Even when the GPMC has a maximum 16-bit +address width, it supports devices with 32-bit word registers. +For example with an SMSC LAN911x/912x controller connected to the TI GPMC on an +OMAP2+ board, "bank-width = <2>;" and "reg-io-width = <4>;". + +Required properties: +- bank-width: Address width of the device in bytes. GPMC supports 8-bit + and 16-bit devices and so must be either 1 or 2 bytes. +- compatible: Compatible string property for the ethernet child device. +- gpmc,cs-on-ns: Chip-select assertion time +- gpmc,cs-rd-off-ns: Chip-select de-assertion time for reads +- gpmc,cs-wr-off-ns: Chip-select de-assertion time for writes +- gpmc,oe-on-ns: Output-enable assertion time +- gpmc,oe-off-ns: Output-enable de-assertion time +- gpmc,we-on-ns: Write-enable assertion time +- gpmc,we-off-ns: Write-enable de-assertion time +- gpmc,access-ns: Start cycle to first data capture (read access) +- gpmc,rd-cycle-ns: Total read cycle time +- gpmc,wr-cycle-ns: Total write cycle time +- reg: Chip-select, base address (relative to chip-select) + and size of the memory mapped for the device. + Note that base address will be typically 0 as this + is the start of the chip-select. + +Optional properties: +- gpmc,XXX Additional GPMC timings and settings parameters. See + Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt + +Example: + +gpmc: gpmc@6e000000 { + compatible = "ti,omap3430-gpmc"; + ti,hwmods = "gpmc"; + reg = <0x6e000000 0x1000>; + interrupts = <20>; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <4>; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <5 0 0x2c000000 0x1000000>; + + ethernet@5,0 { + compatible = "smsc,lan9221", "smsc,lan9115"; + reg = <5 0 0xff>; + bank-width = <2>; + + gpmc,mux-add-data; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <186>; + gpmc,cs-wr-off-ns = <186>; + gpmc,adv-on-ns = <12>; + gpmc,adv-rd-off-ns = <48>; + gpmc,adv-wr-off-ns = <48>; + gpmc,oe-on-ns = <54>; + gpmc,oe-off-ns = <168>; + gpmc,we-on-ns = <54>; + gpmc,we-off-ns = <168>; + gpmc,rd-cycle-ns = <186>; + gpmc,wr-cycle-ns = <186>; + gpmc,access-ns = <114>; + gpmc,page-burst-access-ns = <6>; + gpmc,bus-turnaround-ns = <12>; + gpmc,cycle2cycle-delay-ns = <18>; + gpmc,wr-data-mux-bus-ns = <90>; + gpmc,wr-access-ns = <186>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + + interrupt-parent = <&gpio6>; + interrupts = <16>; + vmmc-supply = <&vddvario>; + vmmc_aux-supply = <&vdd33a>; + reg-io-width = <4>; + + smsc,save-mac-address; + }; +}; diff --git a/Documentation/devicetree/bindings/net/hisilicon-femac-mdio.txt b/Documentation/devicetree/bindings/net/hisilicon-femac-mdio.txt new file mode 100644 index 000000000..23a39a309 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-femac-mdio.txt @@ -0,0 +1,22 @@ +Hisilicon Fast Ethernet MDIO Controller interface + +Required properties: +- compatible: should be "hisilicon,hisi-femac-mdio". +- reg: address and length of the register set for the device. +- clocks: A phandle to the reference clock for this device. + +- PHY subnode: inherits from phy binding [1] +[1] Documentation/devicetree/bindings/net/phy.txt + +Example: +mdio: mdio@10091100 { + compatible = "hisilicon,hisi-femac-mdio"; + reg = <0x10091100 0x10>; + clocks = <&crg HI3516CV300_MDIO_CLK>; + #address-cells = <1>; + #size-cells = <0>; + + phy0: phy@1 { + reg = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/hisilicon-femac.txt b/Documentation/devicetree/bindings/net/hisilicon-femac.txt new file mode 100644 index 000000000..d11af5eca --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-femac.txt @@ -0,0 +1,39 @@ +Hisilicon Fast Ethernet MAC controller + +Required properties: +- compatible: should contain one of the following version strings: + * "hisilicon,hisi-femac-v1" + * "hisilicon,hisi-femac-v2" + and the soc string "hisilicon,hi3516cv300-femac". +- reg: specifies base physical address(s) and size of the device registers. + The first region is the MAC core register base and size. + The second region is the global MAC control register. +- interrupts: should contain the MAC interrupt. +- clocks: A phandle to the MAC main clock. +- resets: should contain the phandle to the MAC reset signal(required) and + the PHY reset signal(optional). +- reset-names: should contain the reset signal name "mac"(required) + and "phy"(optional). +- mac-address: see ethernet.txt [1]. +- phy-mode: see ethernet.txt [1]. +- phy-handle: see ethernet.txt [1]. +- hisilicon,phy-reset-delays-us: triplet of delays if PHY reset signal given. + The 1st cell is reset pre-delay in micro seconds. + The 2nd cell is reset pulse in micro seconds. + The 3rd cell is reset post-delay in micro seconds. + +[1] Documentation/devicetree/bindings/net/ethernet.txt + +Example: + hisi_femac: ethernet@10090000 { + compatible = "hisilicon,hi3516cv300-femac","hisilicon,hisi-femac-v2"; + reg = <0x10090000 0x1000>,<0x10091300 0x200>; + interrupts = <12>; + clocks = <&crg HI3518EV200_ETH_CLK>; + resets = <&crg 0xec 0>,<&crg 0xec 3>; + reset-names = "mac","phy"; + mac-address = [00 00 00 00 00 00]; + phy-mode = "mii"; + phy-handle = <&phy0>; + hisilicon,phy-reset-delays-us = <10000 20000 20000>; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt new file mode 100644 index 000000000..d1df8a00e --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hip04-net.txt @@ -0,0 +1,88 @@ +Hisilicon hip04 Ethernet Controller + +* Ethernet controller node + +Required properties: +- compatible: should be "hisilicon,hip04-mac". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device. +- port-handle: <phandle port channel> + phandle, specifies a reference to the syscon ppe node + port, port number connected to the controller + channel, recv channel start from channel * number (RX_DESC_NUM) +- phy-mode: see ethernet.txt [1]. + +Optional properties: +- phy-handle: see ethernet.txt [1]. + +[1] Documentation/devicetree/bindings/net/ethernet.txt + + +* Ethernet ppe node: +Control rx & tx fifos of all ethernet controllers. +Have 2048 recv channels shared by all ethernet controllers, only if no overlap. +Each controller's recv channel start from channel * number (RX_DESC_NUM). + +Required properties: +- compatible: "hisilicon,hip04-ppe", "syscon". +- reg: address and length of the register set for the device. + + +* MDIO bus node: + +Required properties: + +- compatible: should be "hisilicon,mdio". +- Inherits from MDIO bus node binding [2] +[2] Documentation/devicetree/bindings/net/phy.txt + +Example: + mdio { + compatible = "hisilicon,mdio"; + reg = <0x28f1000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + marvell,reg-init = <18 0x14 0 0x8001>; + }; + + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + marvell,reg-init = <18 0x14 0 0x8001>; + }; + }; + + ppe: ppe@28c0000 { + compatible = "hisilicon,hip04-ppe", "syscon"; + reg = <0x28c0000 0x10000>; + }; + + fe: ethernet@28b0000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x28b0000 0x10000>; + interrupts = <0 413 4>; + phy-mode = "mii"; + port-handle = <&ppe 31 0>; + }; + + ge0: ethernet@2800000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x2800000 0x10000>; + interrupts = <0 402 4>; + phy-mode = "sgmii"; + port-handle = <&ppe 0 1>; + phy-handle = <&phy0>; + }; + + ge8: ethernet@2880000 { + compatible = "hisilicon,hip04-mac"; + reg = <0x2880000 0x10000>; + interrupts = <0 410 4>; + phy-mode = "sgmii"; + port-handle = <&ppe 8 2>; + phy-handle = <&phy1>; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt new file mode 100644 index 000000000..eea73adc6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hix5hd2-gmac.txt @@ -0,0 +1,58 @@ +Hisilicon hix5hd2 gmac controller + +Required properties: +- compatible: should contain one of the following SoC strings: + * "hisilicon,hix5hd2-gmac" + * "hisilicon,hi3798cv200-gmac" + * "hisilicon,hi3516a-gmac" + and one of the following version string: + * "hisilicon,hisi-gmac-v1" + * "hisilicon,hisi-gmac-v2" + The version v1 includes SoCs hix5hd2. + The version v2 includes SoCs hi3798cv200, hi3516a. +- reg: specifies base physical address(s) and size of the device registers. + The first region is the MAC register base and size. + The second region is external interface control register. +- interrupts: should contain the MAC interrupt. +- #address-cells: must be <1>. +- #size-cells: must be <0>. +- phy-mode: see ethernet.txt [1]. +- phy-handle: see ethernet.txt [1]. +- mac-address: see ethernet.txt [1]. +- clocks: clock phandle and specifier pair. +- clock-names: contain the clock name "mac_core"(required) and "mac_ifc"(optional). +- resets: should contain the phandle to the MAC core reset signal(optional), + the MAC interface reset signal(optional) + and the PHY reset signal(optional). +- reset-names: contain the reset signal name "mac_core"(optional), + "mac_ifc"(optional) and "phy"(optional). +- hisilicon,phy-reset-delays-us: triplet of delays if PHY reset signal given. + The 1st cell is reset pre-delay in micro seconds. + The 2nd cell is reset pulse in micro seconds. + The 3rd cell is reset post-delay in micro seconds. + +- PHY subnode: inherits from phy binding [2] + +[1] Documentation/devicetree/bindings/net/ethernet.txt +[2] Documentation/devicetree/bindings/net/phy.txt + +Example: + gmac0: ethernet@f9840000 { + compatible = "hisilicon,hi3798cv200-gmac", "hisilicon,hisi-gmac-v2"; + reg = <0xf9840000 0x1000>,<0xf984300c 0x4>; + interrupts = <0 71 4>; + #address-cells = <1>; + #size-cells = <0>; + phy-mode = "rgmii"; + phy-handle = <&phy2>; + mac-address = [00 00 00 00 00 00]; + clocks = <&crg HISTB_ETH0_MAC_CLK>, <&crg HISTB_ETH0_MACIF_CLK>; + clock-names = "mac_core", "mac_ifc"; + resets = <&crg 0xcc 8>, <&crg 0xcc 10>, <&crg 0xcc 12>; + reset-names = "mac_core", "mac_ifc", "phy"; + hisilicon,phy-reset-delays-us = <10000 10000 30000>; + + phy2: ethernet-phy@2 { + reg = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt new file mode 100644 index 000000000..8ee4b1ced --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt @@ -0,0 +1,90 @@ +Hisilicon DSA Fabric device controller + +Required properties: +- compatible: should be "hisilicon,hns-dsaf-v1" or "hisilicon,hns-dsaf-v2". + "hisilicon,hns-dsaf-v1" is for hip05. + "hisilicon,hns-dsaf-v2" is for Hi1610 and Hi1612. +- mode: dsa fabric mode string. only support one of dsaf modes like these: + "2port-64vf", + "6port-16rss", + "6port-16vf", + "single-port". +- interrupts: should contain the DSA Fabric and rcb interrupt. +- reg: specifies base physical address(es) and size of the device registers. + The first region is external interface control register base and size(optional, + only used when subctrl-syscon does not exist). It is recommended using + subctrl-syscon rather than this address. + The second region is SerDes base register and size(optional, only used when + serdes-syscon in port node does not exist). It is recommended using + serdes-syscon rather than this address. + The third region is the PPE register base and size. + The fourth region is dsa fabric base register and size. It is not required for + single-port mode. +- reg-names: may be ppe-base and(or) dsaf-base. It is used to find the + corresponding reg's index. + +- phy-handle: phy handle of physical port, 0 if not any phy device. It is optional + attribute. If port node exists, phy-handle in each port node will be used. + see ethernet.txt [1]. +- subctrl-syscon: is syscon handle for external interface control register. +- reset-field-offset: is offset of reset field. Its value depends on the hardware + user manual. +- buf-size: rx buffer size, should be 16-1024. +- desc-num: number of description in TX and RX queue, should be 512, 1024, 2048 or 4096. + +- port: subnodes of dsaf. A dsaf node may contain several port nodes(Depending + on mode of dsaf). Port node contain some attributes listed below: +- reg: is physical port index in one dsaf. +- phy-handle: phy handle of physical port. It is not required if there isn't + phy device. see ethernet.txt [1]. +- serdes-syscon: is syscon handle for SerDes register. +- cpld-syscon: is syscon handle + register offset pair for cpld register. It is + not required if there isn't cpld device. +- port-rst-offset: is offset of reset field for each port in dsaf. Its value + depends on the hardware user manual. +- port-mode-offset: is offset of port mode field for each port in dsaf. Its + value depends on the hardware user manual. +- mc-mac-mask: mask of multicast address, determines bit in multicast address + to set: + 1 stands for this bit will be precisely matched, TCAM will check this bit of + MAC address. + 0 stands for this bit will be fuzzy matched, TCAM won't care about this bit + of MAC address. + +[1] Documentation/devicetree/bindings/net/phy.txt + +Example: + +dsaf0: dsa@c7000000 { + compatible = "hisilicon,hns-dsaf-v1"; + mode = "6port-16rss"; + interrupt-parent = <&mbigen_dsa>; + reg = <0x0 0xc5000000 0x0 0x890000 + 0x0 0xc7000000 0x0 0x60000>; + reg-names = "ppe-base", "dsaf-base"; + subctrl-syscon = <&subctrl>; + reset-field-offset = 0; + interrupts = <131 4>,<132 4>, <133 4>,<134 4>, + <135 4>,<136 4>, <137 4>,<138 4>, + <139 4>,<140 4>, <141 4>,<142 4>, + <143 4>,<144 4>, <145 4>,<146 4>, + <147 4>,<148 4>, <384 1>,<385 1>, + <386 1>,<387 1>, <388 1>,<389 1>, + <390 1>,<391 1>, + buf-size = <4096>; + desc-num = <1024>; + dma-coherent; + + port@0 { + reg = 0; + phy-handle = <&phy0>; + serdes-syscon = <&serdes>; + mc-mac-mask = [ff f0 00 00 00 00]; + }; + + port@1 { + reg = 1; + serdes-syscon = <&serdes>; + mc-mac-mask = [ff f0 00 00 00 00]; + }; +}; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt new file mode 100644 index 000000000..4a7ede965 --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-mdio.txt @@ -0,0 +1,27 @@ +Hisilicon MDIO bus controller + +Properties: +- compatible: can be one of: + "hisilicon,hns-mdio" + "hisilicon,mdio" + "hisilicon,hns-mdio" is recommended to be used for hip05 and later SOCs, + while "hisilicon,mdio" is optional for backwards compatibility only on + hip04 Soc. +- reg: The base address of the MDIO bus controller register bank. +- #address-cells: Must be <1>. +- #size-cells: Must be <0>. MDIO addresses have no size component. + +Typically an MDIO bus might have several children. + +Example: + mdio@803c0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "hisilicon,hns-mdio","hisilicon,mdio"; + reg = <0x0 0x803c0000 0x0 0x10000>; + + ethernet-phy@0 { + ... + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt new file mode 100644 index 000000000..f0421ee3c --- /dev/null +++ b/Documentation/devicetree/bindings/net/hisilicon-hns-nic.txt @@ -0,0 +1,76 @@ +Hisilicon Network Subsystem NIC controller + +Required properties: +- compatible: "hisilicon,hns-nic-v1" or "hisilicon,hns-nic-v2". + "hisilicon,hns-nic-v1" is for hip05. + "hisilicon,hns-nic-v2" is for Hi1610 and Hi1612. +- ae-handle: accelerator engine handle for hns, + specifies a reference to the associating hardware driver node. + see Documentation/devicetree/bindings/net/hisilicon-hns-dsaf.txt +- port-id: is the index of port provided by DSAF (the accelerator). DSAF can + connect to 8 PHYs. Port 0 to 1 are both used for administration purpose. They + are called debug ports. + + The remaining 6 PHYs are taken according to the mode of DSAF. + + In NIC mode of DSAF, all 6 PHYs are taken as ethernet ports to the CPU. The + port-id can be 2 to 7. Here is the diagram: + +-----+---------------+ + | CPU | + +-+-+-+---+-+-+-+-+-+-+ + | | | | | | | | + debug service + port port + (0,1) (2-7) + + In Switch mode of DSAF, all 6 PHYs are taken as physical ports connect to a + LAN Switch while the CPU side assume itself have one single NIC connect to + this switch. In this case, the port-id will be 2 only. + +-----+---------------+ + | CPU | + +-+-+-+---+-+-+-+-+-+-+ + | | service| port(2) + debug +------------+ + port | switch | + (0,1) +-+-+-+-+-+-++ + | | | | | | + external port + + This attribute is remained for compatible purpose. It is not recommended to + use it in new code. + +- port-idx-in-ae: is the index of port provided by AE. + In NIC mode of DSAF, all 6 PHYs of service DSAF are taken as ethernet ports + to the CPU. The port-idx-in-ae can be 0 to 5. Here is the diagram: + +-----+---------------+ + | CPU | + +-+-+-+---+-+-+-+-+-+-+ + | | | | | | | | + debug debug service + port port port + (0) (0) (0-5) + + In Switch mode of DSAF, all 6 PHYs of service DSAF are taken as physical + ports connected to a LAN Switch while the CPU side assume itself have one + single NIC connected to this switch. In this case, the port-idx-in-ae + will be 0 only. + +-----+-----+------+------+ + | CPU | + +-+-+-+-+-+-+-+-+-+-+-+-+-+ + | | service| port(0) + debug debug +------------+ + port port | switch | + (0) (0) +-+-+-+-+-+-++ + | | | | | | + external port + +- local-mac-address: mac addr of the ethernet interface + +Example: + + ethernet@0{ + compatible = "hisilicon,hns-nic-v1"; + ae-handle = <&dsaf0>; + port-idx-in-ae = <0>; + local-mac-address = [a2 14 e4 4b 56 76]; + }; diff --git a/Documentation/devicetree/bindings/net/ibm,emac.txt b/Documentation/devicetree/bindings/net/ibm,emac.txt new file mode 100644 index 000000000..c0c14aa3f --- /dev/null +++ b/Documentation/devicetree/bindings/net/ibm,emac.txt @@ -0,0 +1,205 @@ + 4xx/Axon EMAC ethernet nodes + + The EMAC ethernet controller in IBM and AMCC 4xx chips, and also + the Axon bridge. To operate this needs to interact with a this + special McMAL DMA controller, and sometimes an RGMII or ZMII + interface. In addition to the nodes and properties described + below, the node for the OPB bus on which the EMAC sits must have a + correct clock-frequency property. + + i) The EMAC node itself + + Required properties: + - device_type : "network" + + - compatible : compatible list, contains 2 entries, first is + "ibm,emac-CHIP" where CHIP is the host ASIC (440gx, + 405gp, Axon) and second is either "ibm,emac" or + "ibm,emac4". For Axon, thus, we have: "ibm,emac-axon", + "ibm,emac4" + - interrupts : <interrupt mapping for EMAC IRQ and WOL IRQ> + - reg : <registers mapping> + - local-mac-address : 6 bytes, MAC address + - mal-device : phandle of the associated McMAL node + - mal-tx-channel : 1 cell, index of the tx channel on McMAL associated + with this EMAC + - mal-rx-channel : 1 cell, index of the rx channel on McMAL associated + with this EMAC + - cell-index : 1 cell, hardware index of the EMAC cell on a given + ASIC (typically 0x0 and 0x1 for EMAC0 and EMAC1 on + each Axon chip) + - max-frame-size : 1 cell, maximum frame size supported in bytes + - rx-fifo-size : 1 cell, Rx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048 + - tx-fifo-size : 1 cell, Tx fifo size in bytes for 10 and 100 Mb/sec + operations. + For Axon, 2048. + - fifo-entry-size : 1 cell, size of a fifo entry (used to calculate + thresholds). + For Axon, 0x00000010 + - mal-burst-size : 1 cell, MAL burst size (used to calculate thresholds) + in bytes. + For Axon, 0x00000100 (I think ...) + - phy-mode : string, mode of operations of the PHY interface. + Supported values are: "mii", "rmii", "smii", "rgmii", + "tbi", "gmii", rtbi", "sgmii". + For Axon on CAB, it is "rgmii" + - mdio-device : 1 cell, required iff using shared MDIO registers + (440EP). phandle of the EMAC to use to drive the + MDIO lines for the PHY used by this EMAC. + - zmii-device : 1 cell, required iff connected to a ZMII. phandle of + the ZMII device node + - zmii-channel : 1 cell, required iff connected to a ZMII. Which ZMII + channel or 0xffffffff if ZMII is only used for MDIO. + - rgmii-device : 1 cell, required iff connected to an RGMII. phandle + of the RGMII device node. + For Axon: phandle of plb5/plb4/opb/rgmii + - rgmii-channel : 1 cell, required iff connected to an RGMII. Which + RGMII channel is used by this EMAC. + Fox Axon: present, whatever value is appropriate for each + EMAC, that is the content of the current (bogus) "phy-port" + property. + + Optional properties: + - phy-address : 1 cell, optional, MDIO address of the PHY. If absent, + a search is performed. + - phy-map : 1 cell, optional, bitmap of addresses to probe the PHY + for, used if phy-address is absent. bit 0x00000001 is + MDIO address 0. + For Axon it can be absent, though my current driver + doesn't handle phy-address yet so for now, keep + 0x00ffffff in it. + - phy-handle : Used to describe configurations where a external PHY + is used. Please refer to: + Documentation/devicetree/bindings/net/ethernet.txt + - rx-fifo-size-gige : 1 cell, Rx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + rx-fifo-size). For Axon, either absent or 2048. + - tx-fifo-size-gige : 1 cell, Tx fifo size in bytes for 1000 Mb/sec + operations (if absent the value is the same as + tx-fifo-size). For Axon, either absent or 2048. + - tah-device : 1 cell, optional. If connected to a TAH engine for + offload, phandle of the TAH device node. + - tah-channel : 1 cell, optional. If appropriate, channel used on the + TAH engine. + - fixed-link : Fixed-link subnode describing a link to a non-MDIO + managed entity. See + Documentation/devicetree/bindings/net/fixed-link.txt + for details. + - mdio subnode : When the EMAC has a phy connected to its local + mdio, which us supported by the kernel's network + PHY library in drivers/net/phy, there must be device + tree subnode with the following required properties: + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For PHY definitions: Please refer to + Documentation/devicetree/bindings/net/phy.txt and + Documentation/devicetree/bindings/net/ethernet.txt + + Examples: + + EMAC0: ethernet@40000800 { + device_type = "network"; + compatible = "ibm,emac-440gp", "ibm,emac"; + interrupt-parent = <&UIC1>; + interrupts = <1c 4 1d 4>; + reg = <40000800 70>; + local-mac-address = [00 04 AC E3 1B 1E]; + mal-device = <&MAL0>; + mal-tx-channel = <0 1>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <5dc>; + rx-fifo-size = <1000>; + tx-fifo-size = <800>; + phy-mode = "rmii"; + phy-map = <00000001>; + zmii-device = <&ZMII0>; + zmii-channel = <0>; + }; + + EMAC1: ethernet@ef600c00 { + device_type = "network"; + compatible = "ibm,emac-apm821xx", "ibm,emac4sync"; + interrupt-parent = <&EMAC1>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = <0 &UIC2 0x10 IRQ_TYPE_LEVEL_HIGH /* Status */ + 1 &UIC2 0x14 IRQ_TYPE_LEVEL_HIGH /* Wake */>; + reg = <0xef600c00 0x000000c4>; + local-mac-address = [000000000000]; /* Filled in by U-Boot */ + mal-device = <&MAL0>; + mal-tx-channel = <0>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <9000>; + rx-fifo-size = <16384>; + tx-fifo-size = <2048>; + fifo-entry-size = <10>; + phy-mode = "rgmii"; + phy-handle = <&phy0>; + phy-map = <0x00000000>; + rgmii-device = <&RGMII0>; + rgmii-channel = <0>; + tah-device = <&TAH0>; + tah-channel = <0>; + has-inverted-stacr-oc; + has-new-stacr-staopc; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; + }; + + + ii) McMAL node + + Required properties: + - device_type : "dma-controller" + - compatible : compatible list, containing 2 entries, first is + "ibm,mcmal-CHIP" where CHIP is the host ASIC (like + emac) and the second is either "ibm,mcmal" or + "ibm,mcmal2". + For Axon, "ibm,mcmal-axon","ibm,mcmal2" + - interrupts : <interrupt mapping for the MAL interrupts sources: + 5 sources: tx_eob, rx_eob, serr, txde, rxde>. + For Axon: This is _different_ from the current + firmware. We use the "delayed" interrupts for txeob + and rxeob. Thus we end up with mapping those 5 MPIC + interrupts, all level positive sensitive: 10, 11, 32, + 33, 34 (in decimal) + - dcr-reg : < DCR registers range > + - dcr-parent : if needed for dcr-reg + - num-tx-chans : 1 cell, number of Tx channels + - num-rx-chans : 1 cell, number of Rx channels + + iii) ZMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,zmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,zmii". + For Axon, there is no ZMII node. + - reg : <registers mapping> + + iv) RGMII node + + Required properties: + - compatible : compatible list, containing 2 entries, first is + "ibm,rgmii-CHIP" where CHIP is the host ASIC (like + EMAC) and the second is "ibm,rgmii". + For Axon, "ibm,rgmii-axon","ibm,rgmii" + - reg : <registers mapping> + - revision : as provided by the RGMII new version register if + available. + For Axon: 0x0000012a diff --git a/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt b/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt new file mode 100644 index 000000000..d24172cc6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/adf7242.txt @@ -0,0 +1,18 @@ +* ADF7242 IEEE 802.15.4 * + +Required properties: + - compatible: should be "adi,adf7242", "adi,adf7241" + - spi-max-frequency: maximal bus speed (12.5 MHz) + - reg: the chipselect index + - interrupts: the interrupt generated by the device via pin IRQ1. + IRQ_TYPE_LEVEL_HIGH (4) or IRQ_TYPE_EDGE_FALLING (1) + +Example: + + adf7242@0 { + compatible = "adi,adf7242"; + spi-max-frequency = <10000000>; + reg = <0>; + interrupts = <98 IRQ_TYPE_LEVEL_HIGH>; + interrupt-parent = <&gpio3>; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt new file mode 100644 index 000000000..168f1be50 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/at86rf230.txt @@ -0,0 +1,27 @@ +* AT86RF230 IEEE 802.15.4 * + +Required properties: + - compatible: should be "atmel,at86rf230", "atmel,at86rf231", + "atmel,at86rf233" or "atmel,at86rf212" + - spi-max-frequency: maximal bus speed, should be set to 7500000 depends + sync or async operation mode + - reg: the chipselect index + - interrupts: the interrupt generated by the device. Non high-level + can occur deadlocks while handling isr. + +Optional properties: + - reset-gpio: GPIO spec for the rstn pin + - sleep-gpio: GPIO spec for the slp_tr pin + - xtal-trim: u8 value for fine tuning the internal capacitance + arrays of xtal pins: 0 = +0 pF, 0xf = +4.5 pF + +Example: + + at86rf231@0 { + compatible = "atmel,at86rf231"; + spi-max-frequency = <7500000>; + reg = <0>; + interrupts = <19 4>; + interrupt-parent = <&gpio3>; + xtal-trim = /bits/ 8 <0x06>; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/ca8210.txt b/Documentation/devicetree/bindings/net/ieee802154/ca8210.txt new file mode 100644 index 000000000..a1046e636 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/ca8210.txt @@ -0,0 +1,28 @@ +* CA8210 IEEE 802.15.4 * + +Required properties: + - compatible: Should be "cascoda,ca8210" + - reg: Controlling chip select + - spi-max-frequency: Maximum clock speed, should be *less than* + 4000000 + - spi-cpol: Requires inverted clock polarity + - reset-gpio: GPIO attached to reset + - irq-gpio: GPIO attached to IRQ +Optional properties: + - extclock-enable: Include for the ca8210 to route its 16MHz clock + to an output + - extclock-freq: Frequency in Hz of the external clock + - extclock-gpio: GPIO of the ca8210 to output the clock on + +Example: + ca8210@0 { + compatible = "cascoda,ca8210"; + reg = <0>; + spi-max-frequency = <3000000>; + spi-cpol; + reset-gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>; + irq-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + extclock-enable; + extclock-freq = 16000000; + extclock-gpio = 2; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt new file mode 100644 index 000000000..fb6d49f18 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/cc2520.txt @@ -0,0 +1,33 @@ +*CC2520 IEEE 802.15.4 Compatible Radio* + +Required properties: + - compatible: should be "ti,cc2520" + - spi-max-frequency: maximal bus speed (8000000), should be set to 4000000 depends + sync or async operation mode + - reg: the chipselect index + - pinctrl-0: pin control group to be used for this controller. + - pinctrl-names: must contain a "default" entry. + - fifo-gpio: GPIO spec for the FIFO pin + - fifop-gpio: GPIO spec for the FIFOP pin + - sfd-gpio: GPIO spec for the SFD pin + - cca-gpio: GPIO spec for the CCA pin + - vreg-gpio: GPIO spec for the VREG pin + - reset-gpio: GPIO spec for the RESET pin +Optional properties: + - amplified: include if the CC2520 is connected to a CC2591 amplifier + +Example: + cc2520@0 { + compatible = "ti,cc2520"; + reg = <0>; + spi-max-frequency = <4000000>; + amplified; + pinctrl-names = "default"; + pinctrl-0 = <&cc2520_cape_pins>; + fifo-gpio = <&gpio1 18 0>; + fifop-gpio = <&gpio1 19 0>; + sfd-gpio = <&gpio1 13 0>; + cca-gpio = <&gpio1 16 0>; + vreg-gpio = <&gpio0 31 0>; + reset-gpio = <&gpio1 12 0>; + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/mcr20a.txt b/Documentation/devicetree/bindings/net/ieee802154/mcr20a.txt new file mode 100644 index 000000000..2aaef567c --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/mcr20a.txt @@ -0,0 +1,23 @@ +* MCR20A IEEE 802.15.4 * + +Required properties: + - compatible: should be "nxp,mcr20a" + - spi-max-frequency: maximal bus speed, should be set to a frequency + lower than 9000000 depends sync or async operation mode + - reg: the chipselect index + - interrupts: the interrupt generated by the device. Non high-level + can occur deadlocks while handling isr. + +Optional properties: + - rst_b-gpio: GPIO spec for the RST_B pin + +Example: + + mcr20a@0 { + compatible = "nxp,mcr20a"; + spi-max-frequency = <9000000>; + reg = <0>; + interrupts = <17 2>; + interrupt-parent = <&gpio>; + rst_b-gpio = <&gpio 27 1> + }; diff --git a/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt b/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt new file mode 100644 index 000000000..a4ed2efb5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ieee802154/mrf24j40.txt @@ -0,0 +1,20 @@ +* MRF24J40 IEEE 802.15.4 * + +Required properties: + - compatible: should be "microchip,mrf24j40", "microchip,mrf24j40ma", + or "microchip,mrf24j40mc" depends on your transceiver + board + - spi-max-frequency: maximal bus speed, should be set something under or equal + 10000000 + - reg: the chipselect index + - interrupts: the interrupt generated by the device. + +Example: + + mrf24j40ma@0 { + compatible = "microchip,mrf24j40ma"; + spi-max-frequency = <8500000>; + reg = <0>; + interrupts = <19 8>; + interrupt-parent = <&gpio3>; + }; diff --git a/Documentation/devicetree/bindings/net/ipq806x-dwmac.txt b/Documentation/devicetree/bindings/net/ipq806x-dwmac.txt new file mode 100644 index 000000000..6d7ab4e52 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ipq806x-dwmac.txt @@ -0,0 +1,35 @@ +* IPQ806x DWMAC Ethernet controller + +The device inherits all the properties of the dwmac/stmmac devices +described in the file net/stmmac.txt with the following changes. + +Required properties: + +- compatible: should be "qcom,ipq806x-gmac" along with "snps,dwmac" + and any applicable more detailed version number + described in net/stmmac.txt + +- qcom,nss-common: should contain a phandle to a syscon device mapping the + nss-common registers. + +- qcom,qsgmii-csr: should contain a phandle to a syscon device mapping the + qsgmii-csr registers. + +Example: + + gmac: ethernet@37000000 { + device_type = "network"; + compatible = "qcom,ipq806x-gmac"; + reg = <0x37000000 0x200000>; + interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + + qcom,nss-common = <&nss_common>; + qcom,qsgmii-csr = <&qsgmii_csr>; + + clocks = <&gcc GMAC_CORE1_CLK>; + clock-names = "stmmaceth"; + + resets = <&gcc GMAC_CORE1_RESET>; + reset-names = "stmmaceth"; + }; diff --git a/Documentation/devicetree/bindings/net/keystone-netcp.txt b/Documentation/devicetree/bindings/net/keystone-netcp.txt new file mode 100644 index 000000000..04ba1dc34 --- /dev/null +++ b/Documentation/devicetree/bindings/net/keystone-netcp.txt @@ -0,0 +1,221 @@ +This document describes the device tree bindings associated with the +keystone network coprocessor(NetCP) driver support. + +The network coprocessor (NetCP) is a hardware accelerator that processes +Ethernet packets. NetCP has a gigabit Ethernet (GbE) subsystem with a ethernet +switch sub-module to send and receive packets. NetCP also includes a packet +accelerator (PA) module to perform packet classification operations such as +header matching, and packet modification operations such as checksum +generation. NetCP can also optionally include a Security Accelerator (SA) +capable of performing IPSec operations on ingress/egress packets. + +Keystone II SoC's also have a 10 Gigabit Ethernet Subsystem (XGbE) which +includes a 3-port Ethernet switch sub-module capable of 10Gb/s and 1Gb/s rates +per Ethernet port. + +Keystone NetCP driver has a plug-in module architecture where each of the NetCP +sub-modules exist as a loadable kernel module which plug in to the netcp core. +These sub-modules are represented as "netcp-devices" in the dts bindings. It is +mandatory to have the ethernet switch sub-module for the ethernet interface to +be operational. Any other sub-module like the PA is optional. + +NetCP Ethernet SubSystem Layout: + +----------------------------- + NetCP subsystem(10G or 1G) +----------------------------- + | + |-> NetCP Devices -> | + | |-> GBE/XGBE Switch + | | + | |-> Packet Accelerator + | | + | |-> Security Accelerator + | + | + | + |-> NetCP Interfaces -> | + |-> Ethernet Port 0 + | + |-> Ethernet Port 1 + | + |-> Ethernet Port 2 + | + |-> Ethernet Port 3 + + +NetCP subsystem properties: +Required properties: +- compatible: Should be "ti,netcp-1.0" +- clocks: phandle to the reference clocks for the subsystem. +- dma-id: Navigator packet dma instance id. +- ranges: address range of NetCP (includes, Ethernet SS, PA and SA) + +Optional properties: +- reg: register location and the size for the following register + regions in the specified order. + - Efuse MAC address register +- dma-coherent: Present if dma operations are coherent +- big-endian: Keystone devices can be operated in a mode where the DSP is in + the big endian mode. In such cases enable this option. This + option should also be enabled if the ARM is operated in + big endian mode with the DSP in little endian. + +NetCP device properties: Device specification for NetCP sub-modules. +1Gb/10Gb (gbe/xgbe) ethernet switch sub-module specifications. +Required properties: +- label: Must be "netcp-gbe" for 1Gb & "netcp-xgbe" for 10Gb. +- compatible: Must be one of below:- + "ti,netcp-gbe" for 1GbE on NetCP 1.4 + "ti,netcp-gbe-5" for 1GbE N NetCP 1.5 (N=5) + "ti,netcp-gbe-9" for 1GbE N NetCP 1.5 (N=9) + "ti,netcp-gbe-2" for 1GbE N NetCP 1.5 (N=2) + "ti,netcp-xgbe" for 10 GbE + +- reg: register location and the size for the following register + regions in the specified order. + - switch subsystem registers + - sgmii port3/4 module registers (only for NetCP 1.4) + - switch module registers + - serdes registers (only for 10G) + + NetCP 1.4 ethss, here is the order + index #0 - switch subsystem registers + index #1 - sgmii port3/4 module registers + index #2 - switch module registers + + NetCP 1.5 ethss 9 port, 5 port and 2 port + index #0 - switch subsystem registers + index #1 - switch module registers + index #2 - serdes registers + +- tx-channel: the navigator packet dma channel name for tx. +- tx-queue: the navigator queue number associated with the tx dma channel. +- interfaces: specification for each of the switch port to be registered as a + network interface in the stack. +-- slave-port: Switch port number, 0 based numbering. +-- link-interface: type of link interface, supported options are + - mac<->mac auto negotiate mode: 0 + - mac<->phy mode: 1 + - mac<->mac forced mode: 2 + - mac<->fiber mode: 3 + - mac<->phy mode with no mdio: 4 + - 10Gb mac<->phy mode : 10 + - 10Gb mac<->mac forced mode : 11 +----phy-handle: phandle to PHY device + +Optional properties: +- enable-ale: NetCP driver keeps the address learning feature in the ethernet + switch module disabled. This attribute is to enable the address + learning. +- secondary-slave-ports: specification for each of the switch port not be + registered as a network interface. NetCP driver + will only initialize these ports and attach PHY + driver to them if needed. + +NetCP interface properties: Interface specification for NetCP sub-modules. +Required properties: +- rx-channel: the navigator packet dma channel name for rx. +- rx-queue: the navigator queue number associated with rx dma channel. +- rx-pool: specifies the number of descriptors to be used & the region-id + for creating the rx descriptor pool. +- tx-pool: specifies the number of descriptors to be used & the region-id + for creating the tx descriptor pool. +- rx-queue-depth: number of descriptors in each of the free descriptor + queue (FDQ) for the pktdma Rx flow. There can be at + present a maximum of 4 queues per Rx flow. +- rx-buffer-size: the buffer size for each of the Rx flow FDQ. +- tx-completion-queue: the navigator queue number where the descriptors are + recycled after Tx DMA completion. + +Optional properties: +- efuse-mac: If this is 1, then the MAC address for the interface is + obtained from the device efuse mac address register. + If this is 2, the two DWORDs occupied by the MAC address + are swapped. The netcp driver will swap the two DWORDs + back to the proper order when this property is set to 2 + when it obtains the mac address from efuse. +- local-mac-address: the driver is designed to use the of_get_mac_address api + only if efuse-mac is 0. When efuse-mac is 0, the MAC + address is obtained from local-mac-address. If this + attribute is not present, then the driver will use a + random MAC address. +- "netcp-device label": phandle to the device specification for each of NetCP + sub-module attached to this interface. + +Example binding: + +netcp: netcp@2000000 { + reg = <0x2620110 0x8>; + reg-names = "efuse"; + compatible = "ti,netcp-1.0"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x2000000 0xfffff>; + clocks = <&papllclk>, <&clkcpgmac>, <&chipclk12>; + dma-coherent; + /* big-endian; */ + dma-id = <0>; + + netcp-devices { + #address-cells = <1>; + #size-cells = <1>; + ranges; + gbe@90000 { + label = "netcp-gbe"; + reg = <0x90000 0x300>, <0x90400 0x400>, <0x90800 0x700>; + /* enable-ale; */ + tx-queue = <648>; + tx-channel = <8>; + + interfaces { + gbe0: interface-0 { + slave-port = <0>; + link-interface = <4>; + }; + gbe1: interface-1 { + slave-port = <1>; + link-interface = <4>; + }; + }; + + secondary-slave-ports { + port-2 { + slave-port = <2>; + link-interface = <2>; + }; + port-3 { + slave-port = <3>; + link-interface = <2>; + }; + }; + }; + }; + + netcp-interfaces { + interface-0 { + rx-channel = <22>; + rx-pool = <1024 12>; + tx-pool = <1024 12>; + rx-queue-depth = <128 128 0 0>; + rx-buffer-size = <1518 4096 0 0>; + rx-queue = <8704>; + tx-completion-queue = <8706>; + efuse-mac = <1>; + netcp-gbe = <&gbe0>; + + }; + interface-1 { + rx-channel = <23>; + rx-pool = <1024 12>; + tx-pool = <1024 12>; + rx-queue-depth = <128 128 0 0>; + rx-buffer-size = <1518 4096 0 0>; + rx-queue = <8705>; + tx-completion-queue = <8707>; + efuse-mac = <0>; + local-mac-address = [02 18 31 7e 3e 6f]; + netcp-gbe = <&gbe1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/lpc-eth.txt b/Documentation/devicetree/bindings/net/lpc-eth.txt new file mode 100644 index 000000000..b92e92780 --- /dev/null +++ b/Documentation/devicetree/bindings/net/lpc-eth.txt @@ -0,0 +1,23 @@ +* NXP LPC32xx SoC Ethernet Controller + +Required properties: +- compatible: Should be "nxp,lpc-eth" +- reg: Address and length of the register set for the device +- interrupts: Should contain ethernet controller interrupt + +Optional properties: +- phy-mode: See ethernet.txt file in the same directory. If the property is + absent, "rmii" is assumed. +- use-iram: Use LPC32xx internal SRAM (IRAM) for DMA buffering + +Example: + + mac: ethernet@31060000 { + compatible = "nxp,lpc-eth"; + reg = <0x31060000 0x1000>; + interrupt-parent = <&mic>; + interrupts = <29 0>; + + phy-mode = "rmii"; + use-iram; + }; diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt new file mode 100644 index 000000000..3e17ac1d5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/macb.txt @@ -0,0 +1,49 @@ +* Cadence MACB/GEM Ethernet controller + +Required properties: +- compatible: Should be "cdns,[<chip>-]{macb|gem}" + Use "cdns,at91rm9200-emac" Atmel at91rm9200 SoC. + Use "cdns,at91sam9260-macb" for Atmel at91sam9 SoCs or the 10/100Mbit IP + available on sama5d3 SoCs. + Use "cdns,np4-macb" for NP4 SoC devices. + Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb". + Use "cdns,pc302-gem" for Picochip picoXcell pc302 and later devices based on + the Cadence GEM, or the generic form: "cdns,gem". + Use "atmel,sama5d2-gem" for the GEM IP (10/100) available on Atmel sama5d2 SoCs. + Use "atmel,sama5d3-macb" for the 10/100Mbit IP available on Atmel sama5d3 SoCs. + Use "atmel,sama5d3-gem" for the Gigabit IP available on Atmel sama5d3 SoCs. + Use "atmel,sama5d4-gem" for the GEM IP (10/100) available on Atmel sama5d4 SoCs. + Use "cdns,zynq-gem" Xilinx Zynq-7xxx SoC. + Use "cdns,zynqmp-gem" for Zynq Ultrascale+ MPSoC. + Or the generic form: "cdns,emac". +- reg: Address and length of the register set for the device +- interrupts: Should contain macb interrupt +- phy-mode: See ethernet.txt file in the same directory. +- clock-names: Tuple listing input clock names. + Required elements: 'pclk', 'hclk' + Optional elements: 'tx_clk' + Optional elements: 'rx_clk' applies to cdns,zynqmp-gem + Optional elements: 'tsu_clk' +- clocks: Phandles to input clocks. + +Optional properties for PHY child node: +- reset-gpios : Should specify the gpio for phy reset +- magic-packet : If present, indicates that the hardware supports waking + up via magic packet. +- phy-handle : see ethernet.txt file in the same directory + +Examples: + + macb0: ethernet@fffc4000 { + compatible = "cdns,at32ap7000-macb"; + reg = <0xfffc4000 0x4000>; + interrupts = <21>; + phy-mode = "rmii"; + local-mac-address = [3a 0e 03 04 05 06]; + clock-names = "pclk", "hclk", "tx_clk"; + clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>; + ethernet-phy@1 { + reg = <0x1>; + reset-gpios = <&pioE 6 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.txt b/Documentation/devicetree/bindings/net/marvell,prestera.txt new file mode 100644 index 000000000..c329608fa --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell,prestera.txt @@ -0,0 +1,47 @@ +Marvell Prestera Switch Chip bindings +------------------------------------- + +Required properties: +- compatible: one of the following + "marvell,prestera-98dx3236", + "marvell,prestera-98dx3336", + "marvell,prestera-98dx4251", +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device + +Optional properties: +- dfx: phandle reference to the "DFX Server" node + +Example: + +switch { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>; + + packet-processor@0 { + compatible = "marvell,prestera-98dx3236"; + reg = <0 0x4000000>; + interrupts = <33>, <34>, <35>; + dfx = <&dfx>; + }; +}; + +DFX Server bindings +------------------- + +Required properties: +- compatible: must be "marvell,dfx-server", "simple-bus" +- ranges: describes the address mapping of a memory-mapped bus. +- reg: address and length of the register set for the device. + +Example: + +dfx-server { + compatible = "marvell,dfx-server", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>; + reg = <MBUS_ID(0x08, 0x00) 0 0x100000>; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt new file mode 100644 index 000000000..bedcfd5a5 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt @@ -0,0 +1,49 @@ +* Marvell Armada 370 / Armada XP / Armada 3700 Ethernet Controller (NETA) + +Required properties: +- compatible: could be one of the following: + "marvell,armada-370-neta" + "marvell,armada-xp-neta" + "marvell,armada-3700-neta" +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device +- phy: See ethernet.txt file in the same directory. +- phy-mode: See ethernet.txt file in the same directory +- clocks: List of clocks for this device. At least one clock is + mandatory for the core clock. If several clocks are given, then the + clock-names property must be used to identify them. + +Optional properties: +- tx-csum-limit: maximum mtu supported by port that allow TX checksum. + Value is presented in bytes. If not used, by default 1600B is set for + "marvell,armada-370-neta" and 9800B for others. +- clock-names: List of names corresponding to clocks property; shall be + "core" for core clock and "bus" for the optional bus clock. + + +Optional properties (valid only for Armada XP/38x): + +- buffer-manager: a phandle to a buffer manager node. Please refer to + Documentation/devicetree/bindings/net/marvell-neta-bm.txt +- bm,pool-long: ID of a pool, that will accept all packets of a size + higher than 'short' pool's threshold (if set) and up to MTU value. + Obligatory, when the port is supposed to use hardware + buffer management. +- bm,pool-short: ID of a pool, that will be used for accepting + packets of a size lower than given threshold. If not set, the port + will use a single 'long' pool for all packets, as defined above. + +Example: + +ethernet@70000 { + compatible = "marvell,armada-370-neta"; + reg = <0x70000 0x2500>; + interrupts = <8>; + clocks = <&gate_clk 4>; + tx-csum-limit = <9800> + phy = <&phy0>; + phy-mode = "rgmii-id"; + buffer-manager = <&bm>; + bm,pool-long = <0>; + bm,pool-short = <1>; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt new file mode 100644 index 000000000..957e5e5c2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt @@ -0,0 +1,83 @@ +Marvell 8897/8997 (sd8897/sd8997) bluetooth devices (SDIO or USB based) +------ +The 8997 devices supports multiple interfaces. When used on SDIO interfaces, +the btmrvl driver is used and when used on USB interface, the btusb driver is +used. + +Required properties: + + - compatible : should be one of the following: + * "marvell,sd8897-bt" (for SDIO) + * "marvell,sd8997-bt" (for SDIO) + * "usb1286,204e" (for USB) + +Optional properties: + + - marvell,cal-data: Calibration data downloaded to the device during + initialization. This is an array of 28 values(u8). + This is only applicable to SDIO devices. + + - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip. + firmware will use the pin to wakeup host system (u16). + - marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host + platform. The value will be configured to firmware. This + is needed to work chip's sleep feature as expected (u16). + - interrupt-names: Used only for USB based devices (See below) + - interrupts : specifies the interrupt pin number to the cpu. For SDIO, the + driver will use the first interrupt specified in the interrupt + array. For USB based devices, the driver will use the interrupt + named "wakeup" from the interrupt-names and interrupt arrays. + The driver will request an irq based on this interrupt number. + During system suspend, the irq will be enabled so that the + bluetooth chip can wakeup host platform under certain + conditions. During system resume, the irq will be disabled + to make sure unnecessary interrupt is not received. + +Example: + +IRQ pin 119 is used as system wakeup source interrupt. +wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host +using this device side pin and wakeup latency. + +Example for SDIO device follows (calibration data is also available in +below example). + +&mmc3 { + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + btmrvl: bluetooth@2 { + compatible = "marvell,sd8897-bt"; + reg = <2>; + interrupt-parent = <&pio>; + interrupts = <119 IRQ_TYPE_LEVEL_LOW>; + + marvell,cal-data = /bits/ 8 < + 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 + 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 + 0x00 0x00 0xf0 0x00>; + marvell,wakeup-pin = /bits/ 16 <0x0d>; + marvell,wakeup-gap-ms = /bits/ 16 <0x64>; + }; +}; + +Example for USB device: + +&usb_host1_ohci { + #address-cells = <1>; + #size-cells = <0>; + + mvl_bt1: bt@1 { + compatible = "usb1286,204e"; + reg = <1>; + interrupt-parent = <&gpio0>; + interrupt-names = "wakeup"; + interrupts = <119 IRQ_TYPE_LEVEL_LOW>; + marvell,wakeup-pin = /bits/ 16 <0x0d>; + marvell,wakeup-gap-ms = /bits/ 16 <0x64>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-neta-bm.txt b/Documentation/devicetree/bindings/net/marvell-neta-bm.txt new file mode 100644 index 000000000..07b31050d --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-neta-bm.txt @@ -0,0 +1,47 @@ +* Marvell Armada 380/XP Buffer Manager driver (BM) + +Required properties: + +- compatible: should be "marvell,armada-380-neta-bm". +- reg: address and length of the register set for the device. +- clocks: a pointer to the reference clock for this device. +- internal-mem: a phandle to BM internal SRAM definition. + +Optional properties (port): + +- pool<0 : 3>,capacity: size of external buffer pointers' ring maintained + in DRAM. Can be set for each pool (id 0 : 3) separately. The value has + to be chosen between 128 and 16352 and it also has to be aligned to 32. + Otherwise the driver would adjust a given number or choose default if + not set. +- pool<0 : 3>,pkt-size: maximum size of a packet accepted by a given buffer + pointers' pool (id 0 : 3). It will be taken into consideration only when pool + type is 'short'. For 'long' ones it would be overridden by port's MTU. + If not set a driver will choose a default value. + +In order to see how to hook the BM to a given ethernet port, please +refer to Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt. + +Example: + +- main node: + +bm: bm@c8000 { + compatible = "marvell,armada-380-neta-bm"; + reg = <0xc8000 0xac>; + clocks = <&gateclk 13>; + internal-mem = <&bm_bppi>; + pool2,capacity = <4096>; + pool1,pkt-size = <512>; +}; + +- internal SRAM node: + +bm_bppi: bm-bppi { + compatible = "mmio-sram"; + reg = <MBUS_ID(0x0c, 0x04) 0 0x100000>; + ranges = <0 MBUS_ID(0x0c, 0x04) 0 0x100000>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&gateclk 13>; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt new file mode 100644 index 000000000..3f3cfc1d8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-orion-mdio.txt @@ -0,0 +1,54 @@ +* Marvell MDIO Ethernet Controller interface + +The Ethernet controllers of the Marvel Kirkwood, Dove, Orion5x, +MV78xx0, Armada 370, Armada XP, Armada 7k and Armada 8k have an +identical unit that provides an interface with the MDIO bus. +Additionally, Armada 7k and Armada 8k has a second unit which +provides an interface with the xMDIO bus. This driver handles +these interfaces. + +Required properties: +- compatible: "marvell,orion-mdio" or "marvell,xmdio" +- reg: address and length of the MDIO registers. When an interrupt is + not present, the length is the size of the SMI register (4 bytes) + otherwise it must be 0x84 bytes to cover the interrupt control + registers. + +Optional properties: +- interrupts: interrupt line number for the SMI error/done interrupt +- clocks: phandle for up to four required clocks for the MDIO instance + +The child nodes of the MDIO driver are the individual PHY devices +connected to this MDIO bus. They must have a "reg" property given the +PHY address on the MDIO bus. + +Example at the SoC level without an interrupt property: + +mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; + reg = <0xd0072004 0x4>; +}; + +Example with an interrupt property: + +mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; + reg = <0xd0072004 0x84>; + interrupts = <30>; +}; + +And at the board level: + +mdio { + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; +} diff --git a/Documentation/devicetree/bindings/net/marvell-orion-net.txt b/Documentation/devicetree/bindings/net/marvell-orion-net.txt new file mode 100644 index 000000000..6fd988c84 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-orion-net.txt @@ -0,0 +1,83 @@ +Marvell Orion/Discovery ethernet controller +============================================= + +The Marvell Discovery ethernet controller can be found on Marvell Orion SoCs +(Kirkwood, Dove, Orion5x, and Discovery Innovation) and as part of Marvell +Discovery system controller chips (mv64[345]60). + +The Discovery ethernet controller is described with two levels of nodes. The +first level describes the ethernet controller itself and the second level +describes up to 3 ethernet port nodes within that controller. The reason for +the multiple levels is that the port registers are interleaved within a single +set of controller registers. Each port node describes port-specific properties. + +Note: The above separation is only true for Discovery system controllers. +For Orion SoCs we stick to the separation, although there each controller has +only one port associated. Multiple ports are implemented as multiple single-port +controllers. As Kirkwood has some issues with proper initialization after reset, +an extra compatible string is added for it. + +* Ethernet controller node + +Required controller properties: + - #address-cells: shall be 1. + - #size-cells: shall be 0. + - compatible: shall be one of "marvell,orion-eth", "marvell,kirkwood-eth". + - reg: address and length of the controller registers. + +Optional controller properties: + - clocks: phandle reference to the controller clock. + - marvell,tx-checksum-limit: max tx packet size for hardware checksum. + +* Ethernet port node + +Required port properties: + - compatible: shall be one of "marvell,orion-eth-port", + "marvell,kirkwood-eth-port". + - reg: port number relative to ethernet controller, shall be 0, 1, or 2. + - interrupts: port interrupt. + - local-mac-address: See ethernet.txt file in the same directory. + +Optional port properties: + - marvell,tx-queue-size: size of the transmit ring buffer. + - marvell,tx-sram-addr: address of transmit descriptor buffer located in SRAM. + - marvell,tx-sram-size: size of transmit descriptor buffer located in SRAM. + - marvell,rx-queue-size: size of the receive ring buffer. + - marvell,rx-sram-addr: address of receive descriptor buffer located in SRAM. + - marvell,rx-sram-size: size of receive descriptor buffer located in SRAM. + +and + + - phy-handle: See ethernet.txt file in the same directory. + - phy-mode: See ethernet.txt file in the same directory. + +or + + - speed: port speed if no PHY connected. + - duplex: port mode if no PHY connected. + +* Node example: + +mdio-bus { + ... + ethphy: ethernet-phy@8 { + ... + }; +}; + +eth: ethernet-controller@72000 { + compatible = "marvell,orion-eth"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x72000 0x2000>; + clocks = <&gate_clk 2>; + marvell,tx-checksum-limit = <1600>; + + ethernet@0 { + compatible = "marvell,orion-eth-port"; + reg = <0>; + interrupts = <29>; + phy-handle = <ðphy>; + local-mac-address = [00 00 00 00 00 00]; + }; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-pp2.txt b/Documentation/devicetree/bindings/net/marvell-pp2.txt new file mode 100644 index 000000000..fc019df0d --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-pp2.txt @@ -0,0 +1,122 @@ +* Marvell Armada 375 Ethernet Controller (PPv2.1) + Marvell Armada 7K/8K Ethernet Controller (PPv2.2) + +Required properties: + +- compatible: should be one of: + "marvell,armada-375-pp2" + "marvell,armada-7k-pp2" +- reg: addresses and length of the register sets for the device. + For "marvell,armada-375-pp2", must contain the following register + sets: + - common controller registers + - LMS registers + - one register area per Ethernet port + For "marvell,armada-7k-pp2", must contain the following register + sets: + - packet processor registers + - networking interfaces registers + +- clocks: pointers to the reference clocks for this device, consequently: + - main controller clock (for both armada-375-pp2 and armada-7k-pp2) + - GOP clock (for both armada-375-pp2 and armada-7k-pp2) + - MG clock (only for armada-7k-pp2) + - MG Core clock (only for armada-7k-pp2) + - AXI clock (only for armada-7k-pp2) +- clock-names: names of used clocks, must be "pp_clk", "gop_clk", "mg_clk", + "mg_core_clk" and "axi_clk" (the 3 latter only for armada-7k-pp2). + +The ethernet ports are represented by subnodes. At least one port is +required. + +Required properties (port): + +- interrupts: interrupt for the port +- port-id: ID of the port from the MAC point of view +- gop-port-id: only for marvell,armada-7k-pp2, ID of the port from the + GOP (Group Of Ports) point of view. This ID is used to index the + per-port registers in the second register area. +- phy-mode: See ethernet.txt file in the same directory + +Optional properties (port): + +- marvell,loopback: port is loopback mode +- phy: a phandle to a phy node defining the PHY address (as the reg + property, a single integer). +- interrupt-names: if more than a single interrupt for rx is given, must + be the name associated to the interrupts listed. Valid + names are: "tx-cpu0", "tx-cpu1", "tx-cpu2", "tx-cpu3", + "rx-shared", "link". +- marvell,system-controller: a phandle to the system controller. + +Example for marvell,armada-375-pp2: + +ethernet@f0000 { + compatible = "marvell,armada-375-pp2"; + reg = <0xf0000 0xa000>, + <0xc0000 0x3060>, + <0xc4000 0x100>, + <0xc5000 0x100>; + clocks = <&gateclk 3>, <&gateclk 19>; + clock-names = "pp_clk", "gop_clk"; + + eth0: eth0@c4000 { + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + port-id = <0>; + phy = <&phy0>; + phy-mode = "gmii"; + }; + + eth1: eth1@c5000 { + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; + port-id = <1>; + phy = <&phy3>; + phy-mode = "gmii"; + }; +}; + +Example for marvell,armada-7k-pp2: + +cpm_ethernet: ethernet@0 { + compatible = "marvell,armada-7k-pp22"; + reg = <0x0 0x100000>, <0x129000 0xb000>; + clocks = <&cpm_syscon0 1 3>, <&cpm_syscon0 1 9>, + <&cpm_syscon0 1 5>, <&cpm_syscon0 1 6>, <&cpm_syscon0 1 18>; + clock-names = "pp_clk", "gop_clk", "mg_clk", "mg_core_clk", "axi_clk"; + + eth0: eth0 { + interrupts = <ICU_GRP_NSR 39 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 43 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 47 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 51 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 55 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", + "tx-cpu3", "rx-shared"; + port-id = <0>; + gop-port-id = <0>; + }; + + eth1: eth1 { + interrupts = <ICU_GRP_NSR 40 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 44 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 48 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 52 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 56 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", + "tx-cpu3", "rx-shared"; + port-id = <1>; + gop-port-id = <2>; + }; + + eth2: eth2 { + interrupts = <ICU_GRP_NSR 41 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 45 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 49 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 53 IRQ_TYPE_LEVEL_HIGH>, + <ICU_GRP_NSR 57 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx-cpu0", "tx-cpu1", "tx-cpu2", + "tx-cpu3", "rx-shared"; + port-id = <2>; + gop-port-id = <3>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/marvell-pxa168.txt b/Documentation/devicetree/bindings/net/marvell-pxa168.txt new file mode 100644 index 000000000..845a148a3 --- /dev/null +++ b/Documentation/devicetree/bindings/net/marvell-pxa168.txt @@ -0,0 +1,36 @@ +* Marvell PXA168 Ethernet Controller + +Required properties: +- compatible: should be "marvell,pxa168-eth". +- reg: address and length of the register set for the device. +- interrupts: interrupt for the device. +- clocks: pointer to the clock for the device. + +Optional properties: +- port-id: Ethernet port number. Should be '0','1' or '2'. +- #address-cells: must be 1 when using sub-nodes. +- #size-cells: must be 0 when using sub-nodes. +- phy-handle: see ethernet.txt file in the same directory. +- local-mac-address: see ethernet.txt file in the same directory. + +Sub-nodes: +Each PHY can be represented as a sub-node. This is not mandatory. + +Sub-nodes required properties: +- reg: the MDIO address of the PHY. + +Example: + + eth0: ethernet@f7b90000 { + compatible = "marvell,pxa168-eth"; + reg = <0xf7b90000 0x10000>; + clocks = <&chip CLKID_GETH0>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + phy-handle = <ðphy0>; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/maxim,ds26522.txt b/Documentation/devicetree/bindings/net/maxim,ds26522.txt new file mode 100644 index 000000000..ee8bb725f --- /dev/null +++ b/Documentation/devicetree/bindings/net/maxim,ds26522.txt @@ -0,0 +1,13 @@ +* Maxim (Dallas) DS26522 Dual T1/E1/J1 Transceiver + +Required properties: +- compatible: Should contain "maxim,ds26522". +- reg: SPI CS. +- spi-max-frequency: SPI clock. + +Example: + slic@1 { + compatible = "maxim,ds26522"; + reg = <1>; + spi-max-frequency = <2000000>; /* input clock */ + }; diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.txt b/Documentation/devicetree/bindings/net/mdio-gpio.txt new file mode 100644 index 000000000..8dbcf8295 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-gpio.txt @@ -0,0 +1,26 @@ +MDIO on GPIOs + +Currently defined compatibles: +- virtual,gpio-mdio + +MDC and MDIO lines connected to GPIO controllers are listed in the +gpios property as described in section VIII.1 in the following order: + +MDC, MDIO. + +Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases" +node. + +Example: + +aliases { + mdio-gpio0 = &mdio0; +}; + +mdio0: mdio { + compatible = "virtual,mdio-gpio"; + #address-cells = <1>; + #size-cells = <0>; + gpios = <&qe_pio_a 11 + &qe_pio_c 6>; +}; diff --git a/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt new file mode 100644 index 000000000..694987d3c --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-gpio.txt @@ -0,0 +1,119 @@ +Properties for an MDIO bus multiplexer/switch controlled by GPIO pins. + +This is a special case of a MDIO bus multiplexer. One or more GPIO +lines are used to control which child bus is connected. + +Required properties in addition to the generic multiplexer properties: + +- compatible : mdio-mux-gpio. +- gpios : GPIO specifiers for each GPIO line. One or more must be specified. + + +Example : + + /* The parent MDIO bus. */ + smi1: mdio@1180000001900 { + compatible = "cavium,octeon-3860-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0x00001900 0x0 0x40>; + }; + + /* + An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a + pair of GPIO lines. Child busses 2 and 3 populated with 4 + PHYs each. + */ + mdio-mux { + compatible = "mdio-mux-gpio"; + gpios = <&gpio1 3 0>, <&gpio1 4 0>; + mdio-parent-bus = <&smi1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy11: ethernet-phy@1 { + reg = <1>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy12: ethernet-phy@2 { + reg = <2>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy13: ethernet-phy@3 { + reg = <3>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy14: ethernet-phy@4 { + reg = <4>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + }; + + mdio@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + phy21: ethernet-phy@1 { + reg = <1>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy22: ethernet-phy@2 { + reg = <2>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy23: ethernet-phy@3 { + reg = <3>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy24: ethernet-phy@4 { + reg = <4>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt new file mode 100644 index 000000000..065e8bdb9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux-mmioreg.txt @@ -0,0 +1,75 @@ +Properties for an MDIO bus multiplexer controlled by a memory-mapped device + +This is a special case of a MDIO bus multiplexer. A memory-mapped device, +like an FPGA, is used to control which child bus is connected. The mdio-mux +node must be a child of the memory-mapped device. The driver currently only +supports devices with 8, 16 or 32-bit registers. + +Required properties in addition to the generic multiplexer properties: + +- compatible : string, must contain "mdio-mux-mmioreg" + +- reg : integer, contains the offset of the register that controls the bus + multiplexer. The size field in the 'reg' property is the size of + register, and must therefore be 1, 2, or 4. + +- mux-mask : integer, contains an eight-bit mask that specifies which + bits in the register control the actual bus multiplexer. The + 'reg' property of each child mdio-mux node must be constrained by + this mask. + +Example: + +The FPGA node defines a memory-mapped FPGA with a register space of 0x30 bytes. +For the "EMI2" MDIO bus, register 9 (BRDCFG1) controls the mux on that bus. +A bitmask of 0x6 means that bits 1 and 2 (bit 0 is lsb) are the bits on +BRDCFG1 that control the actual mux. + + /* The FPGA node */ + fpga: board-control@3,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p5020ds-fpga", "fsl,fpga-ngpixis"; + reg = <3 0 0x30>; + ranges = <0 3 0 0x30>; + + mdio-mux-emi2 { + compatible = "mdio-mux-mmioreg", "mdio-mux"; + mdio-parent-bus = <&xmdio0>; + #address-cells = <1>; + #size-cells = <0>; + reg = <9 1>; // BRDCFG1 + mux-mask = <0x6>; // EMI2 + + emi2_slot1: mdio@0 { // Slot 1 XAUI (FM2) + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + phy_xgmii_slot1: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <4>; + }; + }; + + emi2_slot2: mdio@2 { // Slot 2 XAUI (FM1) + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy_xgmii_slot2: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0>; + }; + }; + }; + }; + + /* The parent MDIO bus. */ + xmdio0: mdio@f1000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,fman-xmdio"; + reg = <0xf1000 0x1000>; + interrupts = <100 1 0 0>; + }; diff --git a/Documentation/devicetree/bindings/net/mdio-mux.txt b/Documentation/devicetree/bindings/net/mdio-mux.txt new file mode 100644 index 000000000..f58571f36 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio-mux.txt @@ -0,0 +1,129 @@ +Common MDIO bus multiplexer/switch properties. + +An MDIO bus multiplexer/switch will have several child busses that are +numbered uniquely in a device dependent manner. The nodes for an MDIO +bus multiplexer/switch will have one child node for each child bus. + +Required properties: +- #address-cells = <1>; +- #size-cells = <0>; + +Optional properties: +- mdio-parent-bus : phandle to the parent MDIO bus. + +- Other properties specific to the multiplexer/switch hardware. + +Required properties for child nodes: +- #address-cells = <1>; +- #size-cells = <0>; +- reg : The sub-bus number. + + +Example : + + /* The parent MDIO bus. */ + smi1: mdio@1180000001900 { + compatible = "cavium,octeon-3860-mdio"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11800 0x00001900 0x0 0x40>; + }; + + /* + An NXP sn74cbtlv3253 dual 1-of-4 switch controlled by a + pair of GPIO lines. Child busses 2 and 3 populated with 4 + PHYs each. + */ + mdio-mux { + compatible = "mdio-mux-gpio"; + gpios = <&gpio1 3 0>, <&gpio1 4 0>; + mdio-parent-bus = <&smi1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@2 { + reg = <2>; + #address-cells = <1>; + #size-cells = <0>; + + phy11: ethernet-phy@1 { + reg = <1>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy12: ethernet-phy@2 { + reg = <2>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy13: ethernet-phy@3 { + reg = <3>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + phy14: ethernet-phy@4 { + reg = <4>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <10 8>; /* Pin 10, active low */ + }; + }; + + mdio@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + phy21: ethernet-phy@1 { + reg = <1>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy22: ethernet-phy@2 { + reg = <2>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy23: ethernet-phy@3 { + reg = <3>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + phy24: ethernet-phy@4 { + reg = <4>; + marvell,reg-init = <3 0x10 0 0x5777>, + <3 0x11 0 0x00aa>, + <3 0x12 0 0x4105>, + <3 0x13 0 0x0a60>; + interrupt-parent = <&gpio>; + interrupts = <12 8>; /* Pin 12, active low */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mdio.txt b/Documentation/devicetree/bindings/net/mdio.txt new file mode 100644 index 000000000..e3e1603f2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mdio.txt @@ -0,0 +1,37 @@ +Common MDIO bus properties. + +These are generic properties that can apply to any MDIO bus. + +Optional properties: +- reset-gpios: One GPIO that control the RESET lines of all PHYs on that MDIO + bus. +- reset-delay-us: RESET pulse width in microseconds. + +A list of child nodes, one per device on the bus is expected. These +should follow the generic phy.txt, or a device specific binding document. + +The 'reset-delay-us' indicates the RESET signal pulse width in microseconds and +applies to all PHY devices. It must therefore be appropriately determined based +on all PHY requirements (maximum value of all per-PHY RESET pulse widths). + +Example : +This example shows these optional properties, plus other properties +required for the TI Davinci MDIO driver. + + davinci_mdio: ethernet@5c030000 { + compatible = "ti,davinci_mdio"; + reg = <0x5c030000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; + reset-delay-us = <2>; + + ethphy0: ethernet-phy@1 { + reg = <1>; + }; + + ethphy1: ethernet-phy@3 { + reg = <3>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt b/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt new file mode 100644 index 000000000..358fed2fa --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek,mt7620-gsw.txt @@ -0,0 +1,24 @@ +Mediatek Gigabit Switch +======================= + +The mediatek gigabit switch can be found on Mediatek SoCs (mt7620, mt7621). + +Required properties: +- compatible: Should be "mediatek,mt7620-gsw" or "mediatek,mt7621-gsw" +- reg: Address and length of the register set for the device +- interrupts: Should contain the gigabit switches interrupt +- resets: Should contain the gigabit switches resets +- reset-names: Should contain the reset names "gsw" + +Example: + +gsw@10110000 { + compatible = "ralink,mt7620-gsw"; + reg = <0x10110000 8000>; + + resets = <&rstctrl 23>; + reset-names = "gsw"; + + interrupt-parent = <&intc>; + interrupts = <17>; +}; diff --git a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt new file mode 100644 index 000000000..14ceb2a5b --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt @@ -0,0 +1,35 @@ +MediaTek SoC built-in Bluetooth Devices +================================== + +This device is a serial attached device to BTIF device and thus it must be a +child node of the serial node with BTIF. The dt-bindings details for BTIF +device can be known via Documentation/devicetree/bindings/serial/8250.txt. + +Required properties: + +- compatible: Must be + "mediatek,mt7622-bluetooth": for MT7622 SoC +- clocks: Should be the clock specifiers corresponding to the entry in + clock-names property. +- clock-names: Should contain "ref" entries. +- power-domains: Phandle to the power domain that the device is part of + +Example: + + btif: serial@1100c000 { + compatible = "mediatek,mt7622-btif", + "mediatek,mtk-btif"; + reg = <0 0x1100c000 0 0x1000>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_BTIF_PD>; + clock-names = "main"; + reg-shift = <2>; + reg-io-width = <4>; + + bluetooth { + compatible = "mediatek,mt7622-bluetooth"; + power-domains = <&scpsys MT7622_POWER_DOMAIN_WB>; + clocks = <&clk25m>; + clock-names = "ref"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt new file mode 100644 index 000000000..503f2b919 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek-net.txt @@ -0,0 +1,87 @@ +MediaTek Frame Engine Ethernet controller +========================================= + +The frame engine ethernet controller can be found on MediaTek SoCs. These SoCs +have dual GMAC each represented by a child node.. + +* Ethernet controller node + +Required properties: +- compatible: Should be + "mediatek,mt2701-eth": for MT2701 SoC + "mediatek,mt7623-eth", "mediatek,mt2701-eth": for MT7623 SoC + "mediatek,mt7622-eth": for MT7622 SoC +- reg: Address and length of the register set for the device +- interrupts: Should contain the three frame engines interrupts in numeric + order. These are fe_int0, fe_int1 and fe_int2. +- clocks: the clock used by the core +- clock-names: the names of the clock listed in the clocks property. These are + "ethif", "esw", "gp2", "gp1" : For MT2701 and MT7623 SoC + "ethif", "esw", "gp0", "gp1", "gp2", "sgmii_tx250m", "sgmii_rx250m", + "sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll" : For MT7622 SoC +- power-domains: phandle to the power domain that the ethernet is part of +- resets: Should contain phandles to the ethsys reset signals +- reset-names: Should contain the names of reset signal listed in the resets + property + These are "fe", "gmac" and "ppe" +- mediatek,ethsys: phandle to the syscon node that handles the port setup +- mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup + which is required for those SoCs equipped with SGMII such as MT7622 SoC. +- mediatek,pctl: phandle to the syscon node that handles the ports slew rate + and driver current: only for MT2701 and MT7623 SoC + +* Ethernet MAC node + +Required properties: +- compatible: Should be "mediatek,eth-mac" +- reg: The number of the MAC +- phy-handle: see ethernet.txt file in the same directory and + the phy-mode "trgmii" required being provided when reg + is equal to 0 and the MAC uses fixed-link to connect + with internal switch such as MT7530. + +Example: + +eth: ethernet@1b100000 { + compatible = "mediatek,mt7623-eth"; + reg = <0 0x1b100000 0 0x20000>; + clocks = <&topckgen CLK_TOP_ETHIF_SEL>, + <ðsys CLK_ETHSYS_ESW>, + <ðsys CLK_ETHSYS_GP2>, + <ðsys CLK_ETHSYS_GP1>; + clock-names = "ethif", "esw", "gp2", "gp1"; + interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_LOW + GIC_SPI 199 IRQ_TYPE_LEVEL_LOW + GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT2701_POWER_DOMAIN_ETH>; + resets = <ðsys MT2701_ETHSYS_ETH_RST>; + reset-names = "eth"; + mediatek,ethsys = <ðsys>; + mediatek,pctl = <&syscfg_pctl_a>; + #address-cells = <1>; + #size-cells = <0>; + + gmac1: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-handle = <&phy0>; + }; + + gmac2: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-handle = <&phy1>; + }; + + mdio-bus { + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "rgmii"; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + phy-mode = "rgmii"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/meson-dwmac.txt b/Documentation/devicetree/bindings/net/meson-dwmac.txt new file mode 100644 index 000000000..1321bb194 --- /dev/null +++ b/Documentation/devicetree/bindings/net/meson-dwmac.txt @@ -0,0 +1,71 @@ +* Amlogic Meson DWMAC Ethernet controller + +The device inherits all the properties of the dwmac/stmmac devices +described in the file stmmac.txt in the current directory with the +following changes. + +Required properties on all platforms: + +- compatible: Depending on the platform this should be one of: + - "amlogic,meson6-dwmac" + - "amlogic,meson8b-dwmac" + - "amlogic,meson8m2-dwmac" + - "amlogic,meson-gxbb-dwmac" + - "amlogic,meson-axg-dwmac" + Additionally "snps,dwmac" and any applicable more + detailed version number described in net/stmmac.txt + should be used. + +- reg: The first register range should be the one of the DWMAC + controller. The second range is is for the Amlogic specific + configuration (for example the PRG_ETHERNET register range + on Meson8b and newer) + +Required properties on Meson8b, Meson8m2, GXBB and newer: +- clock-names: Should contain the following: + - "stmmaceth" - see stmmac.txt + - "clkin0" - first parent clock of the internal mux + - "clkin1" - second parent clock of the internal mux + +Optional properties on Meson8b, Meson8m2, GXBB and newer: +- amlogic,tx-delay-ns: The internal RGMII TX clock delay (provided + by this driver) in nanoseconds. Allowed values + are: 0ns, 2ns, 4ns, 6ns. + When phy-mode is set to "rgmii" then the TX + delay should be explicitly configured. When + not configured a fallback of 2ns is used. + When the phy-mode is set to either "rgmii-id" + or "rgmii-txid" the TX clock delay is already + provided by the PHY. In that case this + property should be set to 0ns (which disables + the TX clock delay in the MAC to prevent the + clock from going off because both PHY and MAC + are adding a delay). + Any configuration is ignored when the phy-mode + is set to "rmii". + +Example for Meson6: + + ethmac: ethernet@c9410000 { + compatible = "amlogic,meson6-dwmac", "snps,dwmac"; + reg = <0xc9410000 0x10000 + 0xc1108108 0x4>; + interrupts = <0 8 1>; + interrupt-names = "macirq"; + clocks = <&clk81>; + clock-names = "stmmaceth"; + } + +Example for GXBB: + ethmac: ethernet@c9410000 { + compatible = "amlogic,meson-gxbb-dwmac", "snps,dwmac"; + reg = <0x0 0xc9410000 0x0 0x10000>, + <0x0 0xc8834540 0x0 0x8>; + interrupts = <0 8 1>; + interrupt-names = "macirq"; + clocks = <&clkc CLKID_ETH>, + <&clkc CLKID_FCLK_DIV2>, + <&clkc CLKID_MPLL2>; + clock-names = "stmmaceth", "clkin0", "clkin1"; + phy-mode = "rgmii"; + }; diff --git a/Documentation/devicetree/bindings/net/micrel-ks8851.txt b/Documentation/devicetree/bindings/net/micrel-ks8851.txt new file mode 100644 index 000000000..bbdf9a735 --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel-ks8851.txt @@ -0,0 +1,18 @@ +Micrel KS8851 Ethernet mac (MLL) + +Required properties: +- compatible = "micrel,ks8851-mll" of parallel interface +- reg : 2 physical address and size of registers for data and command +- interrupts : interrupt connection + +Micrel KS8851 Ethernet mac (SPI) + +Required properties: +- compatible = "micrel,ks8851" or the deprecated "ks8851" +- reg : chip select number +- interrupts : interrupt connection + +Optional properties: +- vdd-supply: analog 3.3V supply for Ethernet mac +- vdd-io-supply: digital 1.8V IO supply for Ethernet mac +- reset-gpios: reset_n input pin diff --git a/Documentation/devicetree/bindings/net/micrel-ks8995.txt b/Documentation/devicetree/bindings/net/micrel-ks8995.txt new file mode 100644 index 000000000..281bc2498 --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel-ks8995.txt @@ -0,0 +1,20 @@ +Micrel KS8995 SPI controlled Ethernet Switch families + +Required properties (according to spi-bus.txt): +- compatible: either "micrel,ks8995", "micrel,ksz8864" or "micrel,ksz8795" + +Optional properties: +- reset-gpios : phandle of gpio that will be used to reset chip during probe + +Example: + +spi-master { + ... + switch@0 { + compatible = "micrel,ksz8795"; + + reg = <0>; + spi-max-frequency = <50000000>; + reset-gpios = <&gpio0 46 GPIO_ACTIVE_LOW>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt new file mode 100644 index 000000000..e22d8cfea --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel-ksz90x1.txt @@ -0,0 +1,81 @@ +Micrel KSZ9021/KSZ9031 Gigabit Ethernet PHY + +Some boards require special tuning values, particularly when it comes +to clock delays. You can specify clock delay values in the PHY OF +device node. Deprecated, but still supported, these properties can +also be added to an Ethernet OF device node. + +Note that these settings are applied after any phy-specific fixup from +phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c), +and therefore may overwrite them. + +KSZ9021: + + All skew control options are specified in picoseconds. The minimum + value is 0, the maximum value is 3000, and it is incremented by 200ps + steps. + + Optional properties: + + - rxc-skew-ps : Skew control of RXC pad + - rxdv-skew-ps : Skew control of RX CTL pad + - txc-skew-ps : Skew control of TXC pad + - txen-skew-ps : Skew control of TX CTL pad + - rxd0-skew-ps : Skew control of RX data 0 pad + - rxd1-skew-ps : Skew control of RX data 1 pad + - rxd2-skew-ps : Skew control of RX data 2 pad + - rxd3-skew-ps : Skew control of RX data 3 pad + - txd0-skew-ps : Skew control of TX data 0 pad + - txd1-skew-ps : Skew control of TX data 1 pad + - txd2-skew-ps : Skew control of TX data 2 pad + - txd3-skew-ps : Skew control of TX data 3 pad + +KSZ9031: + + All skew control options are specified in picoseconds. The minimum + value is 0, and the maximum is property-dependent. The increment + step is 60ps. The default value is the neutral setting, so setting + rxc-skew-ps=<0> actually results in -900 picoseconds adjustment. + + Optional properties: + + Maximum value of 1860, default value 900: + + - rxc-skew-ps : Skew control of RX clock pad + - txc-skew-ps : Skew control of TX clock pad + + Maximum value of 900, default value 420: + + - rxdv-skew-ps : Skew control of RX CTL pad + - txen-skew-ps : Skew control of TX CTL pad + - rxd0-skew-ps : Skew control of RX data 0 pad + - rxd1-skew-ps : Skew control of RX data 1 pad + - rxd2-skew-ps : Skew control of RX data 2 pad + - rxd3-skew-ps : Skew control of RX data 3 pad + - txd0-skew-ps : Skew control of TX data 0 pad + - txd1-skew-ps : Skew control of TX data 1 pad + - txd2-skew-ps : Skew control of TX data 2 pad + - txd3-skew-ps : Skew control of TX data 3 pad + + - micrel,force-master: + Boolean, force phy to master mode. Only set this option if the phy + reference clock provided at CLK125_NDO pin is used as MAC reference + clock because the clock jitter in slave mode is to high (errata#2). + Attention: The link partner must be configurable as slave otherwise + no link will be established. + +Examples: + + mdio { + phy0: ethernet-phy@0 { + rxc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + txc-skew-ps = <3000>; + txen-skew-ps = <0>; + reg = <0>; + }; + }; + ethernet@70000 { + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; diff --git a/Documentation/devicetree/bindings/net/micrel.txt b/Documentation/devicetree/bindings/net/micrel.txt new file mode 100644 index 000000000..8d157f029 --- /dev/null +++ b/Documentation/devicetree/bindings/net/micrel.txt @@ -0,0 +1,47 @@ +Micrel PHY properties. + +These properties cover the base properties Micrel PHYs. + +Optional properties: + + - micrel,led-mode : LED mode value to set for PHYs with configurable LEDs. + + Configure the LED mode with single value. The list of PHYs and the + bits that are currently supported: + + KSZ8001: register 0x1e, bits 15..14 + KSZ8041: register 0x1e, bits 15..14 + KSZ8021: register 0x1f, bits 5..4 + KSZ8031: register 0x1f, bits 5..4 + KSZ8051: register 0x1f, bits 5..4 + KSZ8081: register 0x1f, bits 5..4 + KSZ8091: register 0x1f, bits 5..4 + + See the respective PHY datasheet for the mode values. + + - micrel,rmii-reference-clock-select-25-mhz: RMII Reference Clock Select + bit selects 25 MHz mode + + Setting the RMII Reference Clock Select bit enables 25 MHz rather + than 50 MHz clock mode. + + Note that this option in only needed for certain PHY revisions with a + non-standard, inverted function of this configuration bit. + Specifically, a clock reference ("rmii-ref" below) is always needed to + actually select a mode. + + - clocks, clock-names: contains clocks according to the common clock bindings. + + supported clocks: + - KSZ8021, KSZ8031, KSZ8081, KSZ8091: "rmii-ref": The RMII reference + input clock. Used to determine the XI input clock. + + - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode + + Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled + by the FXEN boot strapping pin. It can't be determined from the PHY + registers whether the PHY is in fiber mode, so this boolean device tree + property can be used to describe it. + + In fiber mode, auto-negotiation is disabled and the PHY can only work in + 100base-fx (full and half duplex) modes. diff --git a/Documentation/devicetree/bindings/net/microchip,enc28j60.txt b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt new file mode 100644 index 000000000..24626e082 --- /dev/null +++ b/Documentation/devicetree/bindings/net/microchip,enc28j60.txt @@ -0,0 +1,55 @@ +* Microchip ENC28J60 + +This is a standalone 10 MBit ethernet controller with SPI interface. + +For each device connected to a SPI bus, define a child node within +the SPI master node. + +Required properties: +- compatible: Should be "microchip,enc28j60" +- reg: Specify the SPI chip select the ENC28J60 is wired to +- interrupts: Specify the interrupt index within the interrupt controller (referred + to above in interrupt-parent) and interrupt type. The ENC28J60 natively + generates falling edge interrupts, however, additional board logic + might invert the signal. +- pinctrl-names: List of assigned state names, see pinctrl binding documentation. +- pinctrl-0: List of phandles to configure the GPIO pin used as interrupt line, + see also generic and your platform specific pinctrl binding + documentation. + +Optional properties: +- spi-max-frequency: Maximum frequency of the SPI bus when accessing the ENC28J60. + According to the ENC28J80 datasheet, the chip allows a maximum of 20 MHz, however, + board designs may need to limit this value. +- local-mac-address: See ethernet.txt in the same directory. + + +Example (for NXP i.MX28 with pin control stuff for GPIO irq): + + ssp2: ssp@80014000 { + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_b &spi2_sck_cfg>; + + enc28j60: ethernet@0 { + compatible = "microchip,enc28j60"; + pinctrl-names = "default"; + pinctrl-0 = <&enc28j60_pins>; + reg = <0>; + interrupt-parent = <&gpio3>; + interrupts = <3 IRQ_TYPE_EDGE_FALLING>; + spi-max-frequency = <12000000>; + }; + }; + + pinctrl@80018000 { + enc28j60_pins: enc28j60_pins@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART0_RTS__GPIO_3_3 /* Interrupt */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/microchip,lan78xx.txt b/Documentation/devicetree/bindings/net/microchip,lan78xx.txt new file mode 100644 index 000000000..76786a0f6 --- /dev/null +++ b/Documentation/devicetree/bindings/net/microchip,lan78xx.txt @@ -0,0 +1,54 @@ +Microchip LAN78xx Gigabit Ethernet controller + +The LAN78XX devices are usually configured by programming their OTP or with +an external EEPROM, but some platforms (e.g. Raspberry Pi 3 B+) have neither. +The Device Tree properties, if present, override the OTP and EEPROM. + +Required properties: +- compatible: Should be one of "usb424,7800", "usb424,7801" or "usb424,7850". + +Optional properties: +- local-mac-address: see ethernet.txt +- mac-address: see ethernet.txt + +Optional properties of the embedded PHY: +- microchip,led-modes: a 0..4 element vector, with each element configuring + the operating mode of an LED. Omitted LEDs are turned off. Allowed values + are defined in "include/dt-bindings/net/microchip-lan78xx.h". + +Example: + +/* Based on the configuration for a Raspberry Pi 3 B+ */ +&usb { + usb-port@1 { + compatible = "usb424,2514"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + usb-port@1 { + compatible = "usb424,2514"; + reg = <1>; + #address-cells = <1>; + #size-cells = <0>; + + ethernet: ethernet@1 { + compatible = "usb424,7800"; + reg = <1>; + local-mac-address = [ 00 11 22 33 44 55 ]; + + mdio { + #address-cells = <0x1>; + #size-cells = <0x0>; + eth_phy: ethernet-phy@1 { + reg = <1>; + microchip,led-modes = < + LAN78XX_LINK_1000_ACTIVITY + LAN78XX_LINK_10_100_ACTIVITY + >; + }; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/mscc-miim.txt b/Documentation/devicetree/bindings/net/mscc-miim.txt new file mode 100644 index 000000000..7104679cf --- /dev/null +++ b/Documentation/devicetree/bindings/net/mscc-miim.txt @@ -0,0 +1,26 @@ +Microsemi MII Management Controller (MIIM) / MDIO +================================================= + +Properties: +- compatible: must be "mscc,ocelot-miim" +- reg: The base address of the MDIO bus controller register bank. Optionally, a + second register bank can be defined if there is an associated reset register + for internal PHYs +- #address-cells: Must be <1>. +- #size-cells: Must be <0>. MDIO addresses have no size component. +- interrupts: interrupt specifier (refer to the interrupt binding) + +Typically an MDIO bus might have several children. + +Example: + mdio@107009c { + #address-cells = <1>; + #size-cells = <0>; + compatible = "mscc,ocelot-miim"; + reg = <0x107009c 0x36>, <0x10700f0 0x8>; + interrupts = <14>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mscc-ocelot.txt b/Documentation/devicetree/bindings/net/mscc-ocelot.txt new file mode 100644 index 000000000..0a84711ab --- /dev/null +++ b/Documentation/devicetree/bindings/net/mscc-ocelot.txt @@ -0,0 +1,82 @@ +Microsemi Ocelot network Switch +=============================== + +The Microsemi Ocelot network switch can be found on Microsemi SoCs (VSC7513, +VSC7514) + +Required properties: +- compatible: Should be "mscc,vsc7514-switch" +- reg: Must contain an (offset, length) pair of the register set for each + entry in reg-names. +- reg-names: Must include the following entries: + - "sys" + - "rew" + - "qs" + - "hsio" + - "qsys" + - "ana" + - "portX" with X from 0 to the number of last port index available on that + switch +- interrupts: Should contain the switch interrupts for frame extraction and + frame injection +- interrupt-names: should contain the interrupt names: "xtr", "inj" +- ethernet-ports: A container for child nodes representing switch ports. + +The ethernet-ports container has the following properties + +Required properties: + +- #address-cells: Must be 1 +- #size-cells: Must be 0 + +Each port node must have the following mandatory properties: +- reg: Describes the port address in the switch + +Port nodes may also contain the following optional standardised +properties, described in binding documents: + +- phy-handle: Phandle to a PHY on an MDIO bus. See + Documentation/devicetree/bindings/net/ethernet.txt for details. + +Example: + + switch@1010000 { + compatible = "mscc,vsc7514-switch"; + reg = <0x1010000 0x10000>, + <0x1030000 0x10000>, + <0x1080000 0x100>, + <0x10d0000 0x10000>, + <0x11e0000 0x100>, + <0x11f0000 0x100>, + <0x1200000 0x100>, + <0x1210000 0x100>, + <0x1220000 0x100>, + <0x1230000 0x100>, + <0x1240000 0x100>, + <0x1250000 0x100>, + <0x1260000 0x100>, + <0x1270000 0x100>, + <0x1280000 0x100>, + <0x1800000 0x80000>, + <0x1880000 0x10000>; + reg-names = "sys", "rew", "qs", "hsio", "port0", + "port1", "port2", "port3", "port4", "port5", + "port6", "port7", "port8", "port9", "port10", + "qsys", "ana"; + interrupts = <21 22>; + interrupt-names = "xtr", "inj"; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + port0: port@0 { + reg = <0>; + phy-handle = <&phy0>; + }; + port1: port@1 { + reg = <1>; + phy-handle = <&phy1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt new file mode 100644 index 000000000..0eedabe22 --- /dev/null +++ b/Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt @@ -0,0 +1,73 @@ +* Microsemi - vsc8531 Giga bit ethernet phy + +Required properties: +- compatible : Should contain phy id as "ethernet-phy-idAAAA.BBBB" + The PHY device uses the binding described in + Documentation/devicetree/bindings/net/phy.txt + +Optional properties: +- vsc8531,vddmac : The vddmac in mV. Allowed values is listed + in the first row of Table 1 (below). + This property is only used in combination + with the 'edge-slowdown' property. + Default value is 3300. +- vsc8531,edge-slowdown : % the edge should be slowed down relative to + the fastest possible edge time. + Edge rate sets the drive strength of the MAC + interface output signals. Changing the + drive strength will affect the edge rate of + the output signal. The goal of this setting + is to help reduce electrical emission (EMI) + by being able to reprogram drive strength + and in effect slow down the edge rate if + desired. + To adjust the edge-slowdown, the 'vddmac' + must be specified. Table 1 lists the + supported edge-slowdown values for a given + 'vddmac'. + Default value is 0%. + Ref: Table:1 - Edge rate change (below). +- vsc8531,led-0-mode : LED mode. Specify how the LED[0] should behave. + Allowed values are define in + "include/dt-bindings/net/mscc-phy-vsc8531.h". + Default value is VSC8531_LINK_1000_ACTIVITY (1). +- vsc8531,led-1-mode : LED mode. Specify how the LED[1] should behave. + Allowed values are define in + "include/dt-bindings/net/mscc-phy-vsc8531.h". + Default value is VSC8531_LINK_100_ACTIVITY (2). + +Table: 1 - Edge rate change +----------------------------------------------------------------| +| Edge Rate Change (VDDMAC) | +| | +| 3300 mV 2500 mV 1800 mV 1500 mV | +|---------------------------------------------------------------| +| 0% 0% 0% 0% | +| (Fastest) (recommended) (recommended) | +|---------------------------------------------------------------| +| 2% 3% 5% 6% | +|---------------------------------------------------------------| +| 4% 6% 9% 14% | +|---------------------------------------------------------------| +| 7% 10% 16% 21% | +|(recommended) (recommended) | +|---------------------------------------------------------------| +| 10% 14% 23% 29% | +|---------------------------------------------------------------| +| 17% 23% 35% 42% | +|---------------------------------------------------------------| +| 29% 37% 52% 58% | +|---------------------------------------------------------------| +| 53% 63% 76% 77% | +| (slowest) | +|---------------------------------------------------------------| + +Example: + + vsc8531_0: ethernet-phy@0 { + compatible = "ethernet-phy-id0007.0570"; + vsc8531,vddmac = <3300>; + vsc8531,edge-slowdown = <7>; + vsc8531,led-0-mode = <LINK_1000_ACTIVITY>; + vsc8531,led-1-mode = <LINK_100_ACTIVITY>; + }; diff --git a/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt new file mode 100644 index 000000000..c9b35251b --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt @@ -0,0 +1,84 @@ +* Marvell International Ltd. NCI NFC Controller + +Required properties: +- compatible: Should be: + - "marvell,nfc-uart" or "mrvl,nfc-uart" for UART devices + - "marvell,nfc-i2c" for I2C devices + - "marvell,nfc-spi" for SPI devices + +Optional SoC specific properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- reset-n-io: Output GPIO pin used to reset the chip (active low). +- hci-muxed: Specifies that the chip is muxing NCI over HCI frames. + +Optional UART-based chip specific properties: +- flow-control: Specifies that the chip is using RTS/CTS. +- break-control: Specifies that the chip needs specific break management. + +Optional I2C-based chip specific properties: +- i2c-int-falling: Specifies that the chip read event shall be trigged on + falling edge. +- i2c-int-rising: Specifies that the chip read event shall be trigged on + rising edge. + +Example (for ARM-based BeagleBoard Black with 88W8887 on UART5): + +&uart5 { + + nfcmrvluart: nfcmrvluart@5 { + compatible = "marvell,nfc-uart"; + + reset-n-io = <&gpio3 16 0>; + + hci-muxed; + flow-control; + } +}; + + +Example (for ARM-based BeagleBoard Black with 88W8887 on I2C1): + +&i2c1 { + clock-frequency = <400000>; + + nfcmrvli2c0: i2c@1 { + compatible = "marvell,nfc-i2c"; + + reg = <0x8>; + + /* I2C INT configuration */ + interrupt-parent = <&gpio3>; + interrupts = <21 0>; + + /* I2C INT trigger configuration */ + i2c-int-rising; + + /* Reset IO */ + reset-n-io = <&gpio3 19 0>; + }; +}; + + +Example (for ARM-based BeagleBoard Black on SPI0): + +&spi0 { + + mrvlnfcspi0: spi@0 { + compatible = "marvell,nfc-spi"; + + reg = <0>; + + /* SPI Bus configuration */ + spi-max-frequency = <3000000>; + spi-cpha; + spi-cpol; + + /* SPI INT configuration */ + interrupt-parent = <&gpio1>; + interrupts = <17 0>; + + /* Reset IO */ + reset-n-io = <&gpio3 19 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt new file mode 100644 index 000000000..9e4dc510a --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt @@ -0,0 +1,33 @@ +* NXP Semiconductors NXP NCI NFC Controllers + +Required properties: +- compatible: Should be "nxp,nxp-nci-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the chip +- firmware-gpios: Output GPIO pin used to enter firmware download mode + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with NPC100 NFC controller on I2C2): + +&i2c2 { + + + npc100: npc100@29 { + + compatible = "nxp,nxp-nci-i2c"; + + reg = <0x29>; + clock-frequency = <100000>; + + interrupt-parent = <&gpio1>; + interrupts = <29 IRQ_TYPE_LEVEL_HIGH>; + + enable-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt new file mode 100644 index 000000000..2efe3886b --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt @@ -0,0 +1,29 @@ +* NXP Semiconductors PN532 NFC Controller + +Required properties: +- compatible: Should be "nxp,pn532-i2c" or "nxp,pn533-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupts: GPIO interrupt to which the chip is connected + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with PN532 on I2C2): + +&i2c2 { + + + pn532: pn532@24 { + + compatible = "nxp,pn532-i2c"; + + reg = <0x24>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; + + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/pn544.txt b/Documentation/devicetree/bindings/net/nfc/pn544.txt new file mode 100644 index 000000000..2bd82562c --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/pn544.txt @@ -0,0 +1,33 @@ +* NXP Semiconductors PN544 NFC Controller + +Required properties: +- compatible: Should be "nxp,pn544-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the PN544 +- firmware-gpios: Output GPIO pin used to enter firmware download mode + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with PN544 on I2C2): + +&i2c2 { + + + pn544: pn544@28 { + + compatible = "nxp,pn544-i2c"; + + reg = <0x28>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + + enable-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt b/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt new file mode 100644 index 000000000..f02f6fb7f --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt @@ -0,0 +1,25 @@ +* Samsung S3FWRN5 NCI NFC Controller + +Required properties: +- compatible: Should be "samsung,s3fwrn5-i2c". +- reg: address on the bus +- interrupts: GPIO interrupt to which the chip is connected +- s3fwrn5,en-gpios: Output GPIO pin used for enabling/disabling the chip +- s3fwrn5,fw-gpios: Output GPIO pin used to enter firmware mode and + sleep/wakeup control + +Example: + +&hsi2c_4 { + s3fwrn5@27 { + compatible = "samsung,s3fwrn5-i2c"; + + reg = <0x27>; + + interrupt-parent = <&gpa1>; + interrupts = <3 0 0>; + + s3fwrn5,en-gpios = <&gpf1 4 0>; + s3fwrn5,fw-gpios = <&gpj0 2 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt new file mode 100644 index 000000000..baa8f8133 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt @@ -0,0 +1,38 @@ +* STMicroelectronics SAS. ST NCI NFC Controller + +Required properties: +- compatible: Should be "st,st21nfcb-i2c" or "st,st21nfcc-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupts: GPIO interrupt to which the chip is connected +- reset-gpios: Output GPIO pin used to reset the ST21NFCB + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): + +&i2c2 { + + + st21nfcb: st21nfcb@8 { + + compatible = "st,st21nfcb-i2c"; + + reg = <0x08>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt new file mode 100644 index 000000000..d33343330 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt @@ -0,0 +1,36 @@ +* STMicroelectronics SAS. ST NCI NFC Controller + +Required properties: +- compatible: Should be "st,st21nfcb-spi" +- spi-max-frequency: Maximum SPI frequency (<= 4000000). +- interrupts: GPIO interrupt to which the chip is connected +- reset-gpios: Output GPIO pin used to reset the ST21NFCB + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4): + +&mcspi4 { + + + st21nfcb: st21nfcb@0 { + + compatible = "st,st21nfcb-spi"; + + clock-frequency = <4000000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_EDGE_RISING>; + + reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt new file mode 100644 index 000000000..b8bd90f80 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt @@ -0,0 +1,37 @@ +* STMicroelectronics SAS. ST21NFCA NFC Controller + +Required properties: +- compatible: Should be "st,st21nfca-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- enable-gpios: Output GPIO pin used for enabling/disabling the ST21NFCA + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2): + +&i2c2 { + + + st21nfca: st21nfca@1 { + + compatible = "st,st21nfca-i2c"; + + reg = <0x01>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + + enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st95hf.txt b/Documentation/devicetree/bindings/net/nfc/st95hf.txt new file mode 100644 index 000000000..3f373a1e2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st95hf.txt @@ -0,0 +1,45 @@ +* STMicroelectronics : NFC Transceiver ST95HF + +ST NFC Transceiver is required to attach with SPI bus. +ST95HF node should be defined in DT as SPI slave device of SPI +master with which ST95HF transceiver is physically connected. +The properties defined below are required to be the part of DT +to include ST95HF transceiver into the platform. + +Required properties: +=================== +- reg: Address of SPI slave "ST95HF transceiver" on SPI master bus. + +- compatible: should be "st,st95hf" for ST95HF NFC transceiver + +- spi-max-frequency: Max. operating SPI frequency for ST95HF + transceiver. + +- enable-gpio: GPIO line to enable ST95HF transceiver. + +- interrupts : Standard way to define ST95HF transceiver's out + interrupt. + +Optional property: +================= +- st95hfvin-supply : This is an optional property. It contains a + phandle to ST95HF transceiver's regulator supply node in DT. + +Example: +======= +spi@9840000 { + reg = <0x9840000 0x110>; + #address-cells = <1>; + #size-cells = <0>; + cs-gpios = <&pio0 4>; + + st95hf@0{ + reg = <0>; + compatible = "st,st95hf"; + spi-max-frequency = <1000000>; + enable-gpio = <&pio4 0>; + interrupt-parent = <&pio0>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + }; + +}; diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt new file mode 100644 index 000000000..ba1934b95 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt @@ -0,0 +1,43 @@ +* Texas Instruments TRF7970A RFID/NFC/15693 Transceiver + +Required properties: +- compatible: Should be "ti,trf7970a". +- spi-max-frequency: Maximum SPI frequency (<= 2000000). +- interrupts: A single interrupt specifier. +- ti,enable-gpios: One or two GPIO entries used for 'EN' and 'EN2' pins on the + TRF7970A. EN2 is optional. +- vin-supply: Regulator for supply voltage to VIN pin + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- autosuspend-delay: Specify autosuspend delay in milliseconds. +- irq-status-read-quirk: Specify that the trf7970a being used has the + "IRQ Status Read" erratum. +- en2-rf-quirk: Specify that the trf7970a being used has the "EN2 RF" + erratum. +- vdd-io-supply: Regulator specifying voltage for vdd-io +- clock-frequency: Set to specify that the input frequency to the trf7970a is 13560000Hz or 27120000Hz + +Example (for ARM-based BeagleBone with TRF7970A on SPI1): + +&spi1 { + + nfc@0 { + compatible = "ti,trf7970a"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&trf7970a_default>; + spi-max-frequency = <2000000>; + interrupt-parent = <&gpio2>; + interrupts = <14 0>; + ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>, + <&gpio2 5 GPIO_ACTIVE_HIGH>; + vin-supply = <&ldo3_reg>; + vdd-io-supply = <&ldo2_reg>; + autosuspend-delay = <30000>; + irq-status-read-quirk; + en2-rf-quirk; + clock-frequency = <27120000>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nixge.txt b/Documentation/devicetree/bindings/net/nixge.txt new file mode 100644 index 000000000..e55af7f08 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nixge.txt @@ -0,0 +1,32 @@ +* NI XGE Ethernet controller + +Required properties: +- compatible: Should be "ni,xge-enet-2.00" +- reg: Address and length of the register set for the device +- interrupts: Should contain tx and rx interrupt +- interrupt-names: Should be "rx" and "tx" +- phy-mode: See ethernet.txt file in the same directory. +- phy-handle: See ethernet.txt file in the same directory. +- nvmem-cells: Phandle of nvmem cell containing the MAC address +- nvmem-cell-names: Should be "address" + +Examples (10G generic PHY): + nixge0: ethernet@40000000 { + compatible = "ni,xge-enet-2.00"; + reg = <0x40000000 0x6000>; + + nvmem-cells = <ð1_addr>; + nvmem-cell-names = "address"; + + interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "rx", "tx"; + interrupt-parent = <&intc>; + + phy-mode = "xgmii"; + phy-handle = <ðernet_phy1>; + + ethernet_phy1: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <4>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/nokia-bluetooth.txt b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt new file mode 100644 index 000000000..42be7dc9a --- /dev/null +++ b/Documentation/devicetree/bindings/net/nokia-bluetooth.txt @@ -0,0 +1,51 @@ +Nokia Bluetooth Chips +--------------------- + +Nokia phones often come with UART connected bluetooth chips from different +vendors and modified device API. Those devices speak a protocol named H4+ +(also known as h4p) by Nokia, which is similar to the H4 protocol from the +Bluetooth standard. In addition to the H4 protocol it specifies two more +UART status lines for wakeup of UART transceivers to improve power management +and a few new packet types used to negotiate uart speed. + +Required properties: + + - compatible: should contain "nokia,h4p-bluetooth" as well as one of the following: + * "brcm,bcm2048-nokia" + * "ti,wl1271-bluetooth-nokia" + - reset-gpios: GPIO specifier, used to reset the BT module (active low) + - bluetooth-wakeup-gpios: GPIO specifier, used to wakeup the BT module (active high) + - host-wakeup-gpios: GPIO specifier, used to wakeup the host processor (active high) + - clock-names: should be "sysclk" + - clocks: should contain a clock specifier for every name in clock-names + +Optional properties: + + - None + +Example: + +/ { + /* controlled (enabled/disabled) directly by BT module */ + bluetooth_clk: vctcxo { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + }; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + + bluetooth { + compatible = "ti,wl1271-bluetooth-nokia", "nokia,h4p-bluetooth"; + + reset-gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; /* gpio26 */ + host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* gpio101 */ + bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* gpio37 */ + + clocks = <&bluetooth_clk>; + clock-names = "sysclk"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nxp,lpc1850-dwmac.txt b/Documentation/devicetree/bindings/net/nxp,lpc1850-dwmac.txt new file mode 100644 index 000000000..7edba1264 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nxp,lpc1850-dwmac.txt @@ -0,0 +1,20 @@ +* NXP LPC1850 GMAC ethernet controller + +This device is a platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +Required properties: + - compatible: Should contain "nxp,lpc1850-dwmac" + +Examples: + +mac: ethernet@40010000 { + compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac"; + reg = <0x40010000 0x2000>; + interrupts = <5>; + interrupt-names = "macirq"; + clocks = <&ccu1 CLK_CPU_ETHERNET>; + clock-names = "stmmaceth"; + resets = <&rgu 22>; + reset-names = "stmmaceth"; +} diff --git a/Documentation/devicetree/bindings/net/opencores-ethoc.txt b/Documentation/devicetree/bindings/net/opencores-ethoc.txt new file mode 100644 index 000000000..2dc127c30 --- /dev/null +++ b/Documentation/devicetree/bindings/net/opencores-ethoc.txt @@ -0,0 +1,22 @@ +* OpenCores MAC 10/100 Mbps + +Required properties: +- compatible: Should be "opencores,ethoc". +- reg: two memory regions (address and length), + first region is for the device registers and descriptor rings, + second is for the device packet memory. +- interrupts: interrupt for the device. + +Optional properties: +- clocks: phandle to refer to the clk used as per + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Examples: + + enet0: ethoc@fd030000 { + compatible = "opencores,ethoc"; + reg = <0xfd030000 0x4000 0xfd800000 0x4000>; + interrupts = <1>; + local-mac-address = [00 50 c2 13 6f 00]; + clocks = <&osc>; + }; diff --git a/Documentation/devicetree/bindings/net/oxnas-dwmac.txt b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt new file mode 100644 index 000000000..d7117a22f --- /dev/null +++ b/Documentation/devicetree/bindings/net/oxnas-dwmac.txt @@ -0,0 +1,38 @@ +* Oxford Semiconductor OXNAS DWMAC Ethernet controller + +The device inherits all the properties of the dwmac/stmmac devices +described in the file stmmac.txt in the current directory with the +following changes. + +Required properties on all platforms: + +- compatible: For the OX820 SoC, it should be : + - "oxsemi,ox820-dwmac" to select glue + - "snps,dwmac-3.512" to select IP version. + +- clocks: Should contain phandles to the following clocks +- clock-names: Should contain the following: + - "stmmaceth" for the host clock - see stmmac.txt + - "gmac" for the peripheral gate clock + +- oxsemi,sys-ctrl: a phandle to the system controller syscon node + +Example : + +etha: ethernet@40400000 { + compatible = "oxsemi,ox820-dwmac", "snps,dwmac-3.512"; + reg = <0x40400000 0x2000>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq", "eth_wake_irq"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + phy-mode = "rgmii"; + + clocks = <&stdclk CLK_820_ETHA>, <&gmacclk>; + clock-names = "gmac", "stmmaceth"; + resets = <&reset RESET_MAC>; + + /* Regmap for sys registers */ + oxsemi,sys-ctrl = <&sys>; + +}; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt new file mode 100644 index 000000000..17c1d2bd0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -0,0 +1,73 @@ +PHY nodes + +Required properties: + + - interrupts : interrupt specifier for the sole interrupt. + - reg : The ID number for the phy, usually a small integer + +Optional Properties: + +- compatible: Compatible list, may contain + "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for + PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45 + specifications. If neither of these are specified, the default is to + assume clause 22. + + If the PHY reports an incorrect ID (or none at all) then the + "compatible" list may contain an entry with the correct PHY ID in the + form: "ethernet-phy-idAAAA.BBBB" where + AAAA - The value of the 16 bit Phy Identifier 1 register as + 4 hex digits. This is the chip vendor OUI bits 3:18 + BBBB - The value of the 16 bit Phy Identifier 2 register as + 4 hex digits. This is the chip vendor OUI bits 19:24, + followed by 10 bits of a vendor specific ID. + + The compatible list should not contain other values than those + listed here. + +- max-speed: Maximum PHY supported speed (10, 100, 1000...) + +- broken-turn-around: If set, indicates the PHY device does not correctly + release the turn around line low at the end of a MDIO transaction. + +- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to + compensate for the board being designed with the lanes swapped. + +- enet-phy-lane-no-swap: If set, indicates that PHY will disable swap of the + TX/RX lanes. This property allows the PHY to work correcly after e.g. wrong + bootstrap configuration caused by issues in PCB layout design. + +- eee-broken-100tx: +- eee-broken-1000t: +- eee-broken-10gt: +- eee-broken-1000kx: +- eee-broken-10gkx4: +- eee-broken-10gkr: + Mark the corresponding energy efficient ethernet mode as broken and + request the ethernet to stop advertising it. + +- phy-is-integrated: If set, indicates that the PHY is integrated into the same + physical package as the Ethernet MAC. If needed, muxers should be configured + to ensure the integrated PHY is used. The absence of this property indicates + the muxers should be configured so that the external PHY is used. + +- reset-gpios: The GPIO phandle and specifier for the PHY reset signal. + +- reset-assert-us: Delay after the reset was asserted in microseconds. + If this property is missing the delay will be skipped. + +- reset-deassert-us: Delay after the reset was deasserted in microseconds. + If this property is missing the delay will be skipped. + +Example: + +ethernet-phy@0 { + compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c22"; + interrupt-parent = <&PIC>; + interrupts = <35 IRQ_TYPE_EDGE_RISING>; + reg = <0>; + + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + reset-assert-us = <1000>; + reset-deassert-us = <2000>; +}; diff --git a/Documentation/devicetree/bindings/net/qca,qca7000.txt b/Documentation/devicetree/bindings/net/qca,qca7000.txt new file mode 100644 index 000000000..e4a8a5108 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qca,qca7000.txt @@ -0,0 +1,85 @@ +* Qualcomm QCA7000 + +The QCA7000 is a serial-to-powerline bridge with a host interface which could +be configured either as SPI or UART slave. This configuration is done by +the QCA7000 firmware. + +(a) Ethernet over SPI + +In order to use the QCA7000 as SPI device it must be defined as a child of a +SPI master in the device tree. + +Required properties: +- compatible : Should be "qca,qca7000" +- reg : Should specify the SPI chip select +- interrupts : The first cell should specify the index of the source + interrupt and the second cell should specify the trigger + type as rising edge +- spi-cpha : Must be set +- spi-cpol : Must be set + +Optional properties: +- spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at. + Numbers smaller than 1000000 or greater than 16000000 + are invalid. Missing the property will set the SPI + frequency to 8000000 Hertz. +- local-mac-address : see ./ethernet.txt +- qca,legacy-mode : Set the SPI data transfer of the QCA7000 to legacy mode. + In this mode the SPI master must toggle the chip select + between each data word. In burst mode these gaps aren't + necessary, which is faster. This setting depends on how + the QCA7000 is setup via GPIO pin strapping. If the + property is missing the driver defaults to burst mode. + +SPI Example: + +/* Freescale i.MX28 SPI master*/ +ssp2: spi@80014000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx28-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + + qca7000: ethernet@0 { + compatible = "qca,qca7000"; + reg = <0x0>; + interrupt-parent = <&gpio3>; /* GPIO Bank 3 */ + interrupts = <25 0x1>; /* Index: 25, rising edge */ + spi-cpha; /* SPI mode: CPHA=1 */ + spi-cpol; /* SPI mode: CPOL=1 */ + spi-max-frequency = <8000000>; /* freq: 8 MHz */ + local-mac-address = [ A0 B0 C0 D0 E0 F0 ]; + }; +}; + +(b) Ethernet over UART + +In order to use the QCA7000 as UART slave it must be defined as a child of a +UART master in the device tree. It is possible to preconfigure the UART +settings of the QCA7000 firmware, but it's not possible to change them during +runtime. + +Required properties: +- compatible : Should be "qca,qca7000" + +Optional properties: +- local-mac-address : see ./ethernet.txt +- current-speed : current baud rate of QCA7000 which defaults to 115200 + if absent, see also ../serial/slave-device.txt + +UART Example: + +/* Freescale i.MX28 UART */ +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + pinctrl-names = "default"; + pinctrl-0 = <&auart0_2pins_a>; + + qca7000: ethernet { + compatible = "qca,qca7000"; + local-mac-address = [ A0 B0 C0 D0 E0 F0 ]; + current-speed = <38400>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/qcom-emac.txt b/Documentation/devicetree/bindings/net/qcom-emac.txt new file mode 100644 index 000000000..346e6c7f4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/qcom-emac.txt @@ -0,0 +1,111 @@ +Qualcomm Technologies EMAC Gigabit Ethernet Controller + +This network controller consists of two devices: a MAC and an SGMII +internal PHY. Each device is represented by a device tree node. A phandle +connects the MAC node to its corresponding internal phy node. Another +phandle points to the external PHY node. + +Required properties: + +MAC node: +- compatible : Should be "qcom,fsm9900-emac". +- reg : Offset and length of the register regions for the device +- interrupts : Interrupt number used by this controller +- mac-address : The 6-byte MAC address. If present, it is the default + MAC address. +- internal-phy : phandle to the internal PHY node +- phy-handle : phandle the the external PHY node + +Internal PHY node: +- compatible : Should be "qcom,fsm9900-emac-sgmii" or "qcom,qdf2432-emac-sgmii". +- reg : Offset and length of the register region(s) for the device +- interrupts : Interrupt number used by this controller + +The external phy child node: +- reg : The phy address + +Example: + +FSM9900: + +soc { + #address-cells = <1>; + #size-cells = <1>; + + emac0: ethernet@feb20000 { + compatible = "qcom,fsm9900-emac"; + reg = <0xfeb20000 0x10000>, + <0xfeb36000 0x1000>; + interrupts = <76>; + + clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>, + <&gcc 6>, <&gcc 7>; + clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk", + "mdio_clk", "tx_clk", "rx_clk", "sys_clk"; + + internal-phy = <&emac_sgmii>; + + phy-handle = <&phy0>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@0 { + reg = <0>; + }; + + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins_a>; + }; + + emac_sgmii: ethernet@feb38000 { + compatible = "qcom,fsm9900-emac-sgmii"; + reg = <0xfeb38000 0x1000>; + interrupts = <80>; + }; + + tlmm: pinctrl@fd510000 { + compatible = "qcom,fsm9900-pinctrl"; + + mdio_pins_a: mdio { + state { + pins = "gpio123", "gpio124"; + function = "mdio"; + }; + }; + }; + + +QDF2432: + +soc { + #address-cells = <2>; + #size-cells = <2>; + + emac0: ethernet@38800000 { + compatible = "qcom,fsm9900-emac"; + reg = <0x0 0x38800000 0x0 0x10000>, + <0x0 0x38816000 0x0 0x1000>; + interrupts = <0 256 4>; + + clocks = <&gcc 0>, <&gcc 1>, <&gcc 3>, <&gcc 4>, <&gcc 5>, + <&gcc 6>, <&gcc 7>; + clock-names = "axi_clk", "cfg_ahb_clk", "high_speed_clk", + "mdio_clk", "tx_clk", "rx_clk", "sys_clk"; + + internal-phy = <&emac_sgmii>; + + phy-handle = <&phy0>; + + #address-cells = <1>; + #size-cells = <0>; + phy0: ethernet-phy@4 { + reg = <4>; + }; + }; + + emac_sgmii: ethernet@410400 { + compatible = "qcom,qdf2432-emac-sgmii"; + reg = <0x0 0x00410400 0x0 0xc00>, /* Base address */ + <0x0 0x00410000 0x0 0x400>; /* Per-lane digital */ + interrupts = <0 254 1>; + }; diff --git a/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt new file mode 100644 index 000000000..824c0e23c --- /dev/null +++ b/Documentation/devicetree/bindings/net/qualcomm-bluetooth.txt @@ -0,0 +1,55 @@ +Qualcomm Bluetooth Chips +--------------------- + +This documents the binding structure and common properties for serial +attached Qualcomm devices. + +Serial attached Qualcomm devices shall be a child node of the host UART +device the slave device is attached to. + +Required properties: + - compatible: should contain one of the following: + * "qcom,qca6174-bt" + * "qcom,wcn3990-bt" + +Optional properties for compatible string qcom,qca6174-bt: + + - enable-gpios: gpio specifier used to enable chip + - clocks: clock provided to the controller (SUSCLK_32KHZ) + +Required properties for compatible string qcom,wcn3990-bt: + + - vddio-supply: VDD_IO supply regulator handle. + - vddxo-supply: VDD_XO supply regulator handle. + - vddrf-supply: VDD_RF supply regulator handle. + - vddch0-supply: VDD_CH0 supply regulator handle. + +Optional properties for compatible string qcom,wcn3990-bt: + + - max-speed: see Documentation/devicetree/bindings/serial/slave-device.txt + +Examples: + +serial@7570000 { + label = "BT-UART"; + status = "okay"; + + bluetooth { + compatible = "qcom,qca6174-bt"; + + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + }; +}; + +serial@898000 { + bluetooth { + compatible = "qcom,wcn3990-bt"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt b/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt new file mode 100644 index 000000000..9fe1a0a22 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ralink,rt2880-net.txt @@ -0,0 +1,59 @@ +Ralink Frame Engine Ethernet controller +======================================= + +The Ralink frame engine ethernet controller can be found on Ralink and +Mediatek SoCs (RT288x, RT3x5x, RT366x, RT388x, rt5350, mt7620, mt7621, mt76x8). + +Depending on the SoC, there is a number of ports connected to the CPU port +directly and/or via a (gigabit-)switch. + +* Ethernet controller node + +Required properties: +- compatible: Should be one of "ralink,rt2880-eth", "ralink,rt3050-eth", + "ralink,rt3050-eth", "ralink,rt3883-eth", "ralink,rt5350-eth", + "mediatek,mt7620-eth", "mediatek,mt7621-eth" +- reg: Address and length of the register set for the device +- interrupts: Should contain the frame engines interrupt +- resets: Should contain the frame engines resets +- reset-names: Should contain the reset names "fe". If a switch is present + "esw" is also required. + + +* Ethernet port node + +Required properties: +- compatible: Should be "ralink,eth-port" +- reg: The number of the physical port +- phy-handle: reference to the node describing the phy + +Example: + +mdio-bus { + ... + phy0: ethernet-phy@0 { + phy-mode = "mii"; + reg = <0>; + }; +}; + +ethernet@400000 { + compatible = "ralink,rt2880-eth"; + reg = <0x00400000 10000>; + + #address-cells = <1>; + #size-cells = <0>; + + resets = <&rstctrl 18>; + reset-names = "fe"; + + interrupt-parent = <&cpuintc>; + interrupts = <5>; + + port@0 { + compatible = "ralink,eth-port"; + reg = <0>; + phy-handle = <&phy0>; + }; + +}; diff --git a/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt b/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt new file mode 100644 index 000000000..87e315856 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ralink,rt3050-esw.txt @@ -0,0 +1,30 @@ +Ralink Fast Ethernet Embedded Switch +==================================== + +The ralink fast ethernet embedded switch can be found on Ralink and Mediatek +SoCs (RT3x5x, RT5350, MT76x8). + +Required properties: +- compatible: Should be "ralink,rt3050-esw" +- reg: Address and length of the register set for the device +- interrupts: Should contain the embedded switches interrupt +- resets: Should contain the embedded switches resets +- reset-names: Should contain the reset names "esw" + +Optional properties: +- ralink,portmap: can be used to choose if the default switch setup is + llllw or wllll +- ralink,led_polarity: override the active high/low settings of the leds + +Example: + +esw@10110000 { + compatible = "ralink,rt3050-esw"; + reg = <0x10110000 8000>; + + resets = <&rstctrl 23>; + reset-names = "esw"; + + interrupt-parent = <&intc>; + interrupts = <17>; +}; diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt new file mode 100644 index 000000000..da249b7c4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt @@ -0,0 +1,129 @@ +* Renesas Electronics Ethernet AVB + +This file provides information on what the device node for the Ethernet AVB +interface contains. + +Required properties: +- compatible: Must contain one or more of the following: + - "renesas,etheravb-r8a7743" for the R8A7743 SoC. + - "renesas,etheravb-r8a7745" for the R8A7745 SoC. + - "renesas,etheravb-r8a77470" for the R8A77470 SoC. + - "renesas,etheravb-r8a7790" for the R8A7790 SoC. + - "renesas,etheravb-r8a7791" for the R8A7791 SoC. + - "renesas,etheravb-r8a7792" for the R8A7792 SoC. + - "renesas,etheravb-r8a7793" for the R8A7793 SoC. + - "renesas,etheravb-r8a7794" for the R8A7794 SoC. + - "renesas,etheravb-rcar-gen2" as a fallback for the above + R-Car Gen2 and RZ/G1 devices. + + - "renesas,etheravb-r8a774a1" for the R8A774A1 SoC. + - "renesas,etheravb-r8a7795" for the R8A7795 SoC. + - "renesas,etheravb-r8a7796" for the R8A7796 SoC. + - "renesas,etheravb-r8a77965" for the R8A77965 SoC. + - "renesas,etheravb-r8a77970" for the R8A77970 SoC. + - "renesas,etheravb-r8a77980" for the R8A77980 SoC. + - "renesas,etheravb-r8a77990" for the R8A77990 SoC. + - "renesas,etheravb-r8a77995" for the R8A77995 SoC. + - "renesas,etheravb-rcar-gen3" as a fallback for the above + R-Car Gen3 and RZ/G2 devices. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first followed by + the generic version. + +- reg: Offset and length of (1) the register block and (2) the stream buffer. + The region for the register block is mandatory. + The region for the stream buffer is optional, as it is only present on + R-Car Gen2 and RZ/G1 SoCs, and on R-Car H3 (R8A7795), M3-W (R8A7796), + and M3-N (R8A77965). +- interrupts: A list of interrupt-specifiers, one for each entry in + interrupt-names. + If interrupt-names is not present, an interrupt specifier + for a single muxed interrupt. +- phy-mode: see ethernet.txt file in the same directory. +- phy-handle: see ethernet.txt file in the same directory. +- #address-cells: number of address cells for the MDIO bus, must be equal to 1. +- #size-cells: number of size cells on the MDIO bus, must be equal to 0. +- clocks: clock phandle and specifier pair. +- pinctrl-0: phandle, referring to a default pin configuration node. + +Optional properties: +- interrupt-names: A list of interrupt names. + For the R-Car Gen 3 SoCs this property is mandatory; + it should include one entry per channel, named "ch%u", + where %u is the channel number ranging from 0 to 24. + For other SoCs this property is optional; if present + it should contain "mux" for a single muxed interrupt. +- pinctrl-names: pin configuration state name ("default"). +- renesas,no-ether-link: boolean, specify when a board does not provide a proper + AVB_LINK signal. +- renesas,ether-link-active-low: boolean, specify when the AVB_LINK signal is + active-low instead of normal active-high. + +Example: + + ethernet@e6800000 { + compatible = "renesas,etheravb-r8a7795", "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 812>; + power-domains = <&cpg>; + phy-mode = "rgmii-id"; + phy-handle = <&phy0>; + + pinctrl-0 = <ðer_pins>; + pinctrl-names = "default"; + renesas,no-ether-link; + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@0 { + rxc-skew-ps = <900>; + rxdv-skew-ps = <0>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txc-skew-ps = <900>; + txen-skew-ps = <0>; + txd0-skew-ps = <0>; + txd1-skew-ps = <0>; + txd2-skew-ps = <0>; + txd3-skew-ps = <0>; + reg = <0>; + interrupt-parent = <&gpio2>; + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt new file mode 100644 index 000000000..3b71da7e8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt @@ -0,0 +1,76 @@ +Rockchip SoC RK3288 10/100/1000 Ethernet driver(GMAC) + +The device node has following properties. + +Required properties: + - compatible: should be "rockchip,<name>-gamc" + "rockchip,px30-gmac": found on PX30 SoCs + "rockchip,rk3128-gmac": found on RK312x SoCs + "rockchip,rk3228-gmac": found on RK322x SoCs + "rockchip,rk3288-gmac": found on RK3288 SoCs + "rockchip,rk3328-gmac": found on RK3328 SoCs + "rockchip,rk3366-gmac": found on RK3366 SoCs + "rockchip,rk3368-gmac": found on RK3368 SoCs + "rockchip,rk3399-gmac": found on RK3399 SoCs + "rockchip,rv1108-gmac": found on RV1108 SoCs + - reg: addresses and length of the register sets for the device. + - interrupts: Should contain the GMAC interrupts. + - interrupt-names: Should contain the interrupt names "macirq". + - rockchip,grf: phandle to the syscon grf used to control speed and mode. + - clocks: <&cru SCLK_MAC>: clock selector for main clock, from PLL or PHY. + <&cru SCLK_MAC_PLL>: PLL clock for SCLK_MAC + <&cru SCLK_MAC_RX>: clock gate for RX + <&cru SCLK_MAC_TX>: clock gate for TX + <&cru SCLK_MACREF>: clock gate for RMII referce clock + <&cru SCLK_MACREF_OUT> clock gate for RMII reference clock output + <&cru ACLK_GMAC>: AXI clock gate for GMAC + <&cru PCLK_GMAC>: APB clock gate for GMAC + - clock-names: One name for each entry in the clocks property. + - phy-mode: See ethernet.txt file in the same directory. + - pinctrl-names: Names corresponding to the numbered pinctrl states. + - pinctrl-0: pin-control mode. can be <&rgmii_pins> or <&rmii_pins>. + - clock_in_out: For RGMII, it must be "input", means main clock(125MHz) + is not sourced from SoC's PLL, but input from PHY; For RMII, "input" means + PHY provides the reference clock(50MHz), "output" means GMAC provides the + reference clock. + - snps,reset-gpio gpio number for phy reset. + - snps,reset-active-low boolean flag to indicate if phy reset is active low. + - assigned-clocks: main clock, should be <&cru SCLK_MAC>; + - assigned-clock-parents = parent of main clock. + can be <&ext_gmac> or <&cru SCLK_MAC_PLL>. + +Optional properties: + - tx_delay: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as default. + - rx_delay: Delay value for RXD timing. Range value is 0~0x7F, 0x10 as default. + - phy-supply: phandle to a regulator if the PHY needs one + +Example: + +gmac: ethernet@ff290000 { + compatible = "rockchip,rk3288-gmac"; + reg = <0xff290000 0x10000>; + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "macirq"; + rockchip,grf = <&grf>; + clocks = <&cru SCLK_MAC>, + <&cru SCLK_MAC_RX>, <&cru SCLK_MAC_TX>, + <&cru SCLK_MACREF>, <&cru SCLK_MACREF_OUT>, + <&cru ACLK_GMAC>, <&cru PCLK_GMAC>; + clock-names = "stmmaceth", + "mac_clk_rx", "mac_clk_tx", + "clk_mac_ref", "clk_mac_refout", + "aclk_mac", "pclk_mac"; + phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii_pins /*&rmii_pins*/>; + + clock_in_out = "input"; + snps,reset-gpio = <&gpio4 7 0>; + snps,reset-active-low; + + assigned-clocks = <&cru SCLK_MAC>; + assigned-clock-parents = <&ext_gmac>; + tx_delay = <0x30>; + rx_delay = <0x10>; + +}; diff --git a/Documentation/devicetree/bindings/net/samsung-sxgbe.txt b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt new file mode 100644 index 000000000..46e591178 --- /dev/null +++ b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt @@ -0,0 +1,50 @@ +* Samsung 10G Ethernet driver (SXGBE) + +Required properties: +- compatible: Should be "samsung,sxgbe-v2.0a" +- reg: Address and length of the register set for the device +- interrupts: Should contain the SXGBE interrupts + These interrupts are ordered by fixed and follows variable + trasmit DMA interrupts, receive DMA interrupts and lpi interrupt. + index 0 - this is fixed common interrupt of SXGBE and it is always + available. + index 1 to 25 - 8 variable trasmit interrupts, variable 16 receive interrupts + and 1 optional lpi interrupt. +- phy-mode: String, operation mode of the PHY interface. + Supported values are: "sgmii", "xgmii". +- samsung,pbl: Integer, Programmable Burst Length. + Supported values are 1, 2, 4, 8, 16, or 32. +- samsung,burst-map: Integer, Program the possible bursts supported by sxgbe + This is an integer and represents allowable DMA bursts when fixed burst. + Allowable range is 0x01-0x3F. When this field is set fixed burst is enabled. + When fixed length is needed for burst mode, it can be set within allowable + range. + +Optional properties: +- mac-address: 6 bytes, mac address +- max-frame-size: Maximum Transfer Unit (IEEE defined MTU), rather + than the maximum frame size. + +Example: + + aliases { + ethernet0 = <&sxgbe0>; + }; + + sxgbe0: ethernet@1a040000 { + compatible = "samsung,sxgbe-v2.0a"; + reg = <0 0x1a040000 0 0x10000>; + interrupt-parent = <&gic>; + interrupts = <0 209 4>, <0 185 4>, <0 186 4>, <0 187 4>, + <0 188 4>, <0 189 4>, <0 190 4>, <0 191 4>, + <0 192 4>, <0 193 4>, <0 194 4>, <0 195 4>, + <0 196 4>, <0 197 4>, <0 198 4>, <0 199 4>, + <0 200 4>, <0 201 4>, <0 202 4>, <0 203 4>, + <0 204 4>, <0 205 4>, <0 206 4>, <0 207 4>, + <0 208 4>, <0 210 4>; + samsung,pbl = <0x08> + samsung,burst-map = <0x20> + mac-address = [ 00 11 22 33 44 55 ]; /* Filled in by U-Boot */ + max-frame-size = <9000>; + phy-mode = "xgmii"; + }; diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt b/Documentation/devicetree/bindings/net/sff,sfp.txt new file mode 100644 index 000000000..832139919 --- /dev/null +++ b/Documentation/devicetree/bindings/net/sff,sfp.txt @@ -0,0 +1,85 @@ +Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP) +Transceiver + +Required properties: + +- compatible : must be one of + "sff,sfp" for SFP modules + "sff,sff" for soldered down SFF modules + +- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial + interface + +Optional Properties: + +- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) + module presence input gpio signal, active (module absent) high. Must + not be present for SFF modules + +- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal + Indication input gpio signal, active (signal lost) high + +- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter + Fault input gpio signal, active (fault condition) high + +- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable + output gpio signal, active (Tx disable) high + +- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate + Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate + Must not be present for SFF modules + +- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate + Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high: + high Tx rate. Must not be present for SFF modules + +- maximum-power-milliwatt : Maximum module power consumption + Specifies the maximum power consumption allowable by a module in the + slot, in milli-Watts. Presently, modules can be up to 1W, 1.5W or 2W. + +Example #1: Direct serdes to SFP connection + +sfp_eth3: sfp-eth3 { + compatible = "sff,sfp"; + i2c-bus = <&sfp_1g_i2c>; + los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>; + maximum-power-milliwatt = <1000>; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>; + tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>; +}; + +&cps_emac3 { + phy-names = "comphy"; + phys = <&cps_comphy5 0>; + sfp = <&sfp_eth3>; +}; + +Example #2: Serdes to PHY to SFP connection + +sfp_eth0: sfp-eth0 { + compatible = "sff,sfp"; + i2c-bus = <&sfpp0_i2c>; + los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cps_sfpp0_pins>; + tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; +}; + +p0_phy: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>; + reg = <0>; + interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>; + sfp = <&sfp_eth0>; +}; + +&cpm_eth0 { + phy = <&p0_phy>; + phy-mode = "10gbase-kr"; +}; diff --git a/Documentation/devicetree/bindings/net/sh_eth.txt b/Documentation/devicetree/bindings/net/sh_eth.txt new file mode 100644 index 000000000..abc362742 --- /dev/null +++ b/Documentation/devicetree/bindings/net/sh_eth.txt @@ -0,0 +1,69 @@ +* Renesas Electronics SH EtherMAC + +This file provides information on what the device node for the SH EtherMAC +interface contains. + +Required properties: +- compatible: Must contain one or more of the following: + "renesas,gether-r8a7740" if the device is a part of R8A7740 SoC. + "renesas,ether-r8a7743" if the device is a part of R8A7743 SoC. + "renesas,ether-r8a7745" if the device is a part of R8A7745 SoC. + "renesas,ether-r8a7778" if the device is a part of R8A7778 SoC. + "renesas,ether-r8a7779" if the device is a part of R8A7779 SoC. + "renesas,ether-r8a7790" if the device is a part of R8A7790 SoC. + "renesas,ether-r8a7791" if the device is a part of R8A7791 SoC. + "renesas,ether-r8a7793" if the device is a part of R8A7793 SoC. + "renesas,ether-r8a7794" if the device is a part of R8A7794 SoC. + "renesas,gether-r8a77980" if the device is a part of R8A77980 SoC. + "renesas,ether-r7s72100" if the device is a part of R7S72100 SoC. + "renesas,ether-r7s9210" if the device is a part of R7S9210 SoC. + "renesas,rcar-gen1-ether" for a generic R-Car Gen1 device. + "renesas,rcar-gen2-ether" for a generic R-Car Gen2 or RZ/G1 + device. + + When compatible with the generic version, nodes must list + the SoC-specific version corresponding to the platform + first followed by the generic version. + +- reg: offset and length of (1) the E-DMAC/feLic register block (required), + (2) the TSU register block (optional). +- interrupts: interrupt specifier for the sole interrupt. +- phy-mode: see ethernet.txt file in the same directory. +- phy-handle: see ethernet.txt file in the same directory. +- #address-cells: number of address cells for the MDIO bus, must be equal to 1. +- #size-cells: number of size cells on the MDIO bus, must be equal to 0. +- clocks: clock phandle and specifier pair. +- pinctrl-0: phandle, referring to a default pin configuration node. + +Optional properties: +- pinctrl-names: pin configuration state name ("default"). +- renesas,no-ether-link: boolean, specify when a board does not provide a proper + Ether LINK signal. +- renesas,ether-link-active-low: boolean, specify when the Ether LINK signal is + active-low instead of normal active-high. + +Example (Lager board): + + ethernet@ee700000 { + compatible = "renesas,ether-r8a7790", + "renesas,rcar-gen2-ether"; + reg = <0 0xee700000 0 0x400>; + interrupt-parent = <&gic>; + interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7790_CLK_ETHER>; + phy-mode = "rmii"; + phy-handle = <&phy1>; + pinctrl-0 = <ðer_pins>; + pinctrl-names = "default"; + renesas,ether-link-active-low; + #address-cells = <1>; + #size-cells = <0>; + + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&irqc0>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + pinctrl-0 = <&phy1_pins>; + pinctrl-names = "default"; + }; + }; diff --git a/Documentation/devicetree/bindings/net/smsc-lan87xx.txt b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt new file mode 100644 index 000000000..8b7c719b0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc-lan87xx.txt @@ -0,0 +1,23 @@ +SMSC LAN87xx Ethernet PHY + +Some boards require special tuning values. Configure them +through an Ethernet OF device node. + +Optional properties: + +- smsc,disable-energy-detect: + If set, do not enable energy detect mode for the SMSC phy. + default: enable energy detect mode + +Examples: +smsc phy with disabled energy detect mode on an am335x based board. +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&davinci_mdio_default>; + pinctrl-1 = <&davinci_mdio_sleep>; + + ethernetphy0: ethernet-phy@0 { + reg = <0>; + smsc,disable-energy-detect; + }; +}; diff --git a/Documentation/devicetree/bindings/net/smsc-lan91c111.txt b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt new file mode 100644 index 000000000..309e37eb7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc-lan91c111.txt @@ -0,0 +1,17 @@ +SMSC LAN91c111 Ethernet mac + +Required properties: +- compatible = "smsc,lan91c111"; +- reg : physical address and size of registers +- interrupts : interrupt connection + +Optional properties: +- phy-device : see ethernet.txt file in the same directory +- reg-io-width : Mask of sizes (in bytes) of the IO accesses that + are supported on the device. Valid value for SMSC LAN91c111 are + 1, 2 or 4. If it's omitted or invalid, the size would be 2 meaning + 16-bit access only. +- power-gpios: GPIO to control the PWRDWN pin +- reset-gpios: GPIO to control the RESET pin +- pxa-u16-align4 : Boolean, put in place the workaround the force all + u16 writes to be 32 bits aligned diff --git a/Documentation/devicetree/bindings/net/smsc911x.txt b/Documentation/devicetree/bindings/net/smsc911x.txt new file mode 100644 index 000000000..acfafc8e1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/smsc911x.txt @@ -0,0 +1,43 @@ +* Smart Mixed-Signal Connectivity (SMSC) LAN911x/912x Controller + +Required properties: +- compatible : Should be "smsc,lan<model>", "smsc,lan9115" +- reg : Address and length of the io space for SMSC LAN +- interrupts : one or two interrupt specifiers + - The first interrupt is the SMSC LAN interrupt line + - The second interrupt (if present) is the PME (power + management event) interrupt that is able to wake up the host + system with a 50ms pulse on network activity +- phy-mode : See ethernet.txt file in the same directory + +Optional properties: +- reg-shift : Specify the quantity to shift the register offsets by +- reg-io-width : Specify the size (in bytes) of the IO accesses that + should be performed on the device. Valid value for SMSC LAN is + 2 or 4. If it's omitted or invalid, the size would be 2. +- smsc,irq-active-high : Indicates the IRQ polarity is active-high +- smsc,irq-push-pull : Indicates the IRQ type is push-pull +- smsc,force-internal-phy : Forces SMSC LAN controller to use + internal PHY +- smsc,force-external-phy : Forces SMSC LAN controller to use + external PHY +- smsc,save-mac-address : Indicates that mac address needs to be saved + before resetting the controller +- reset-gpios : a GPIO line connected to the RESET (active low) signal + of the device. On many systems this is wired high so the device goes + out of reset at power-on, but if it is under program control, this + optional GPIO can wake up in response to it. +- vdd33a-supply, vddvario-supply : 3.3V analog and IO logic power supplies + +Examples: + +lan9220@f4000000 { + compatible = "smsc,lan9220", "smsc,lan9115"; + reg = <0xf4000000 0x2000000>; + phy-mode = "mii"; + interrupt-parent = <&gpio1>; + interrupts = <31>, <32>; + reset-gpios = <&gpio1 30 GPIO_ACTIVE_LOW>; + reg-io-width = <4>; + smsc,irq-push-pull; +}; diff --git a/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt new file mode 100644 index 000000000..36f1aef58 --- /dev/null +++ b/Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt @@ -0,0 +1,167 @@ +* Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC) + +This binding is deprecated, but it continues to be supported, but new +features should be preferably added to the stmmac binding document. + +This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service) +IP block. The IP supports multiple options for bus type, clocking and reset +structure, and feature list. Consequently, a number of properties and list +entries in properties are marked as optional, or only required in specific HW +configurations. + +Required properties: +- compatible: One of: + - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10" + Represents the IP core when integrated into the Axis ARTPEC-6 SoC. + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10" + Represents the IP core when integrated into the NVIDIA Tegra186 SoC. + - "snps,dwc-qos-ethernet-4.10" + This combination is deprecated. It should be treated as equivalent to + "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10". It is supported to be + compatible with earlier revisions of this binding. +- reg: Address and length of the register set for the device +- clocks: Phandle and clock specifiers for each entry in clock-names, in the + same order. See ../clock/clock-bindings.txt. +- clock-names: May contain any/all of the following depending on the IP + configuration, in any order: + - "tx" + The EQOS transmit path clock. The HW signal name is clk_tx_i. + In some configurations (e.g. GMII/RGMII), this clock also drives the PHY TX + path. In other configurations, other clocks (such as tx_125, rmii) may + drive the PHY TX path. + - "rx" + The EQOS receive path clock. The HW signal name is clk_rx_i. + In some configurations (e.g. GMII/RGMII), this clock is derived from the + PHY's RX clock output. In other configurations, other clocks (such as + rx_125, rmii) may drive the EQOS RX path. + In cases where the PHY clock is directly fed into the EQOS receive path + without intervening logic, the DT need not represent this clock, since it + is assumed to be fully under the control of the PHY device/driver. In + cases where SoC integration adds additional logic to this path, such as a + SW-controlled clock gate, this clock should be represented in DT. + - "slave_bus" + The CPU/slave-bus (CSR) interface clock. This applies to any bus type; + APB, AHB, AXI, etc. The HW signal name is hclk_i (AHB) or clk_csr_i (other + buses). + - "master_bus" + The master bus interface clock. Only required in configurations that use a + separate clock for the master and slave bus interfaces. The HW signal name + is hclk_i (AHB) or aclk_i (AXI). + - "ptp_ref" + The PTP reference clock. The HW signal name is clk_ptp_ref_i. + - "phy_ref_clk" + This clock is deprecated and should not be used by new compatible values. + It is equivalent to "tx". + - "apb_pclk" + This clock is deprecated and should not be used by new compatible values. + It is equivalent to "slave_bus". + + Note: Support for additional IP configurations may require adding the + following clocks to this list in the future: clk_rx_125_i, clk_tx_125_i, + clk_pmarx_0_i, clk_pmarx1_i, clk_rmii_i, clk_revmii_rx_i, clk_revmii_tx_i. + Configurations exist where multiple similar clocks are used at once, e.g. all + of clk_rx_125_i, clk_pmarx_0_i, clk_pmarx1_i. For this reason it is best to + extend the binding with a separate clock-names entry for each of those RX + clocks, rather than repurposing the existing "rx" clock-names entry as a + generic/logical clock in a similar fashion to "master_bus" and "slave_bus". + This will allow easy support for configurations that support multiple PHY + interfaces using a mux, and hence need to have explicit control over + specific RX clocks. + + The following compatible values require the following set of clocks: + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10": + - "slave_bus" + - "master_bus" + - "rx" + - "tx" + - "ptp_ref" + - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10": + - "slave_bus" + - "master_bus" + - "tx" + - "ptp_ref" + - "snps,dwc-qos-ethernet-4.10" (deprecated): + - "phy_ref_clk" + - "apb_clk" +- interrupts: Should contain the core's combined interrupt signal +- phy-mode: See ethernet.txt file in the same directory +- resets: Phandle and reset specifiers for each entry in reset-names, in the + same order. See ../reset/reset.txt. +- reset-names: May contain any/all of the following depending on the IP + configuration, in any order: + - "eqos". The reset to the entire module. The HW signal name is hreset_n + (AHB) or aresetn_i (AXI). + + The following compatible values require the following set of resets: + (the reset properties may be omitted if empty) + - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10": + - "eqos". + - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10": + - None. + - "snps,dwc-qos-ethernet-4.10" (deprecated): + - None. + +Optional properties: +- dma-coherent: Present if dma operations are coherent +- mac-address: See ethernet.txt in the same directory +- local-mac-address: See ethernet.txt in the same directory +- phy-reset-gpios: Phandle and specifier for any GPIO used to reset the PHY. + See ../gpio/gpio.txt. +- snps,en-lpi: If present it enables use of the AXI low-power interface +- snps,write-requests: Number of write requests that the AXI port can issue. + It depends on the SoC configuration. +- snps,read-requests: Number of read requests that the AXI port can issue. + It depends on the SoC configuration. +- snps,burst-map: Bitmap of allowed AXI burst lengts, with the LSB + representing 4, then 8 etc. +- snps,txpbl: DMA Programmable burst length for the TX DMA +- snps,rxpbl: DMA Programmable burst length for the RX DMA +- snps,en-tx-lpi-clockgating: Enable gating of the MAC TX clock during + TX low-power mode. +- phy-handle: See ethernet.txt file in the same directory +- mdio device tree subnode: When the GMAC has a phy connected to its local + mdio, there must be device tree subnode with the following + required properties: + - compatible: Must be "snps,dwc-qos-ethernet-mdio". + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For each phy on the mdio bus, there must be a node with the following + fields: + + - reg: phy id used to communicate to phy. + - device_type: Must be "ethernet-phy". + - fixed-mode device tree subnode: see fixed-link.txt in the same directory + +Examples: +ethernet2@40010000 { + clock-names = "phy_ref_clk", "apb_pclk"; + clocks = <&clkc 17>, <&clkc 15>; + compatible = "snps,dwc-qos-ethernet-4.10"; + interrupt-parent = <&intc>; + interrupts = <0x0 0x1e 0x4>; + reg = <0x40010000 0x4000>; + phy-handle = <&phy2>; + phy-mode = "gmii"; + phy-reset-gpios = <&gpioctlr 43 GPIO_ACTIVE_LOW>; + + snps,en-tx-lpi-clockgating; + snps,en-lpi; + snps,write-requests = <2>; + snps,read-requests = <16>; + snps,burst-map = <0x7>; + snps,txpbl = <8>; + snps,rxpbl = <2>; + + dma-coherent; + + mdio { + #address-cells = <0x1>; + #size-cells = <0x0>; + phy2: phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + device_type = "ethernet-phy"; + reg = <0x1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt new file mode 100644 index 000000000..17d681966 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -0,0 +1,51 @@ +Altera SOCFPGA SoC DWMAC controller + +This is a variant of the dwmac/stmmac driver an inherits all descriptions +present in Documentation/devicetree/bindings/net/stmmac.txt. + +The device node has additional properties: + +Required properties: + - compatible : Should contain "altr,socfpga-stmmac" along with + "snps,dwmac" and any applicable more detailed + designware version numbers documented in stmmac.txt + - altr,sysmgr-syscon : Should be the phandle to the system manager node that + encompasses the glue register, the register offset, and the register shift. + - altr,f2h_ptp_ref_clk use f2h_ptp_ref_clk instead of default eosc1 clock + for ptp ref clk. This affects all emacs as the clock is common. + +Optional properties: +altr,emac-splitter: Should be the phandle to the emac splitter soft IP node if + DWMAC controller is connected emac splitter. +phy-mode: The phy mode the ethernet operates in +altr,sgmii-to-sgmii-converter: phandle to the TSE SGMII converter + +This device node has additional phandle dependency, the sgmii converter: + +Required properties: + - compatible : Should be altr,gmii-to-sgmii-2.0 + - reg-names : Should be "eth_tse_control_port" + +Example: + +gmii_to_sgmii_converter: phy@100000240 { + compatible = "altr,gmii-to-sgmii-2.0"; + reg = <0x00000001 0x00000240 0x00000008>, + <0x00000001 0x00000200 0x00000040>; + reg-names = "eth_tse_control_port"; + clocks = <&sgmii_1_clk_0 &emac1 1 &sgmii_clk_125 &sgmii_clk_125>; + clock-names = "tse_pcs_ref_clk_clock_connection", "tse_rx_cdr_refclk"; +}; + +gmac0: ethernet@ff700000 { + compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x60 0>; + reg = <0xff700000 0x2000>; + interrupts = <0 115 4>; + interrupt-names = "macirq"; + mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */ + clocks = <&emac_0_clk>; + clock-names = "stmmaceth"; + phy-mode = "sgmii"; + altr,gmii-to-sgmii-converter = <&gmii_to_sgmii_converter>; +}; diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt new file mode 100644 index 000000000..fc8f01718 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt @@ -0,0 +1,64 @@ +* Socionext AVE ethernet controller + +This describes the devicetree bindings for AVE ethernet controller +implemented on Socionext UniPhier SoCs. + +Required properties: + - compatible: Should be + - "socionext,uniphier-pro4-ave4" : for Pro4 SoC + - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC + - "socionext,uniphier-ld11-ave4" : for LD11 SoC + - "socionext,uniphier-ld20-ave4" : for LD20 SoC + - "socionext,uniphier-pxs3-ave4" : for PXs3 SoC + - reg: Address where registers are mapped and size of region. + - interrupts: Should contain the MAC interrupt. + - phy-mode: See ethernet.txt in the same directory. Allow to choose + "rgmii", "rmii", "mii", or "internal" according to the PHY. + The acceptable mode is SoC-dependent. + - phy-handle: Should point to the external phy device. + See ethernet.txt file in the same directory. + - clocks: A phandle to the clock for the MAC. + For Pro4 SoC, that is "socionext,uniphier-pro4-ave4", + another MAC clock, GIO bus clock and PHY clock are also required. + - clock-names: Should contain + - "ether", "ether-gb", "gio", "ether-phy" for Pro4 SoC + - "ether" for others + - resets: A phandle to the reset control for the MAC. For Pro4 SoC, + GIO bus reset is also required. + - reset-names: Should contain + - "ether", "gio" for Pro4 SoC + - "ether" for others + - socionext,syscon-phy-mode: A phandle to syscon with one argument + that configures phy mode. The argument is the ID of MAC instance. + +Optional properties: + - local-mac-address: See ethernet.txt in the same directory. + +Required subnode: + - mdio: A container for child nodes representing phy nodes. + See phy.txt in the same directory. + +Example: + + ether: ethernet@65000000 { + compatible = "socionext,uniphier-ld20-ave4"; + reg = <0x65000000 0x8500>; + interrupts = <0 66 4>; + phy-mode = "rgmii"; + phy-handle = <ðphy>; + clock-names = "ether"; + clocks = <&sys_clk 6>; + reset-names = "ether"; + resets = <&sys_rst 6>; + socionext,syscon-phy-mode = <&soc_glue 0>; + local-mac-address = [00 00 00 00 00 00]; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy: ethphy@1 { + reg = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/socionext-netsec.txt b/Documentation/devicetree/bindings/net/socionext-netsec.txt new file mode 100644 index 000000000..0cff94fb0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socionext-netsec.txt @@ -0,0 +1,53 @@ +* Socionext NetSec Ethernet Controller IP + +Required properties: +- compatible: Should be "socionext,synquacer-netsec" +- reg: Address and length of the control register area, followed by the + address and length of the EEPROM holding the MAC address and + microengine firmware +- interrupts: Should contain ethernet controller interrupt +- clocks: phandle to the PHY reference clock +- clock-names: Should be "phy_ref_clk" +- phy-mode: See ethernet.txt file in the same directory +- phy-handle: See ethernet.txt in the same directory. + +- mdio device tree subnode: When the Netsec has a phy connected to its local + mdio, there must be device tree subnode with the following + required properties: + + - #address-cells: Must be <1>. + - #size-cells: Must be <0>. + + For each phy on the mdio bus, there must be a node with the following + fields: + - compatible: Refer to phy.txt + - reg: phy id used to communicate to phy. + +Optional properties: (See ethernet.txt file in the same directory) +- dma-coherent: Boolean property, must only be present if memory + accesses performed by the device are cache coherent. +- local-mac-address: See ethernet.txt in the same directory. +- mac-address: See ethernet.txt in the same directory. +- max-speed: See ethernet.txt in the same directory. +- max-frame-size: See ethernet.txt in the same directory. + +Example: + eth0: ethernet@522d0000 { + compatible = "socionext,synquacer-netsec"; + reg = <0 0x522d0000 0x0 0x10000>, <0 0x10000000 0x0 0x10000>; + interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_netsec>; + clock-names = "phy_ref_clk"; + phy-mode = "rgmii"; + max-speed = <1000>; + max-frame-size = <9000>; + phy-handle = <&phy1>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy1: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/sti-dwmac.txt b/Documentation/devicetree/bindings/net/sti-dwmac.txt new file mode 100644 index 000000000..062c5174a --- /dev/null +++ b/Documentation/devicetree/bindings/net/sti-dwmac.txt @@ -0,0 +1,60 @@ +STMicroelectronics SoC DWMAC glue layer controller + +This file documents differences between the core properties in +Documentation/devicetree/bindings/net/stmmac.txt +and what is needed on STi platforms to program the stmmac glue logic. + +The device node has following properties. + +Required properties: + - compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac", + "st,stih407-dwmac", "st,stid127-dwmac". + - st,syscon : Should be phandle/offset pair. The phandle to the syscon node which + encompases the glue register, and the offset of the control register. + - st,gmac_en: this is to enable the gmac into a dedicated sysctl control + register available on STiH407 SoC. + - pinctrl-0: pin-control for all the MII mode supported. + +Optional properties: + - resets : phandle pointing to the system reset controller with correct + reset line index for ethernet reset. + - st,ext-phyclk: valid only for RMII where PHY can generate 50MHz clock or + MAC can generate it. + - st,tx-retime-src: This specifies which clk is wired up to the mac for + retimeing tx lines. This is totally board dependent and can take one of the + posssible values from "txclk", "clk_125" or "clkgen". + If not passed, the internal clock will be used by default. + - sti-ethclk: this is the phy clock. + - sti-clkconf: this is an extra sysconfig register, available in new SoCs, + to program the clk retiming. + - st,gmac_en: to enable the GMAC, this only is present in some SoCs; e.g. + STiH407. + +Example: + +ethernet0: dwmac@9630000 { + device_type = "network"; + compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + reg = <0x9630000 0x8000>; + reg-names = "stmmaceth"; + + st,syscon = <&syscfg_sbc_reg 0x80>; + st,gmac_en; + resets = <&softreset STIH407_ETH1_SOFTRESET>; + reset-names = "stmmaceth"; + + interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>, + <GIC_SPI 99 IRQ_TYPE_NONE>, + <GIC_SPI 100 IRQ_TYPE_NONE>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; + snps,mixed-burst; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii1>; + + clock-names = "stmmaceth", "sti-ethclk"; + clocks = <&CLK_S_C0_FLEXGEN CLK_EXT2F_A9>, + <&CLK_S_C0_FLEXGEN CLK_ETH_PHY>; +}; diff --git a/Documentation/devicetree/bindings/net/stm32-dwmac.txt b/Documentation/devicetree/bindings/net/stm32-dwmac.txt new file mode 100644 index 000000000..134101272 --- /dev/null +++ b/Documentation/devicetree/bindings/net/stm32-dwmac.txt @@ -0,0 +1,45 @@ +STMicroelectronics STM32 / MCU DWMAC glue layer controller + +This file documents platform glue layer for stmmac. +Please see stmmac.txt for the other unchanged properties. + +The device node has following properties. + +Required properties: +- compatible: For MCU family should be "st,stm32-dwmac" to select glue, and + "snps,dwmac-3.50a" to select IP version. + For MPU family should be "st,stm32mp1-dwmac" to select + glue, and "snps,dwmac-4.20a" to select IP version. +- clocks: Must contain a phandle for each entry in clock-names. +- clock-names: Should be "stmmaceth" for the host clock. + Should be "mac-clk-tx" for the MAC TX clock. + Should be "mac-clk-rx" for the MAC RX clock. + For MPU family need to add also "ethstp" for power mode clock and, + "syscfg-clk" for SYSCFG clock. +- interrupt-names: Should contain a list of interrupt names corresponding to + the interrupts in the interrupts property, if available. + Should be "macirq" for the main MAC IRQ + Should be "eth_wake_irq" for the IT which wake up system +- st,syscon : Should be phandle/offset pair. The phandle to the syscon node which + encompases the glue register, and the offset of the control register. + +Optional properties: +- clock-names: For MPU family "mac-clk-ck" for PHY without quartz +- st,int-phyclk (boolean) : valid only where PHY do not have quartz and need to be clock + by RCC + +Example: + + ethernet@40028000 { + compatible = "st,stm32-dwmac", "snps,dwmac-3.50a"; + reg = <0x40028000 0x8000>; + reg-names = "stmmaceth"; + interrupts = <0 61 0>, <0 62 0>; + interrupt-names = "macirq", "eth_wake_irq"; + clock-names = "stmmaceth", "mac-clk-tx", "mac-clk-rx"; + clocks = <&rcc 0 25>, <&rcc 0 26>, <&rcc 0 27>; + st,syscon = <&syscfg 0x4>; + snps,pbl = <8>; + snps,mixed-burst; + dma-ranges; + }; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt new file mode 100644 index 000000000..cb694062a --- /dev/null +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -0,0 +1,178 @@ +* STMicroelectronics 10/100/1000/2500/10000 Ethernet (GMAC/XGMAC) + +Required properties: +- compatible: Should be "snps,dwmac-<ip_version>", "snps,dwmac" or + "snps,dwxgmac-<ip_version>", "snps,dwxgmac". + For backwards compatibility: "st,spear600-gmac" is also supported. +- reg: Address and length of the register set for the device +- interrupts: Should contain the STMMAC interrupts +- interrupt-names: Should contain a list of interrupt names corresponding to + the interrupts in the interrupts property, if available. + Valid interrupt names are: + - "macirq" (combined signal for various interrupt events) + - "eth_wake_irq" (the interrupt to manage the remote wake-up packet detection) + - "eth_lpi" (the interrupt that occurs when Rx exits the LPI state) +- phy-mode: See ethernet.txt file in the same directory. +- snps,reset-gpio gpio number for phy reset. +- snps,reset-active-low boolean flag to indicate if phy reset is active low. +- snps,reset-delays-us is triplet of delays + The 1st cell is reset pre-delay in micro seconds. + The 2nd cell is reset pulse in micro seconds. + The 3rd cell is reset post-delay in micro seconds. + +Optional properties: +- resets: Should contain a phandle to the STMMAC reset signal, if any +- reset-names: Should contain the reset signal name "stmmaceth", if a + reset phandle is given +- max-frame-size: See ethernet.txt file in the same directory +- clocks: If present, the first clock should be the GMAC main clock and + the second clock should be peripheral's register interface clock. Further + clocks may be specified in derived bindings. +- clock-names: One name for each entry in the clocks property, the + first one should be "stmmaceth" and the second one should be "pclk". +- ptp_ref: this is the PTP reference clock; in case of the PTP is available + this clock is used for programming the Timestamp Addend Register. If not + passed then the system clock will be used and this is fine on some + platforms. +- tx-fifo-depth: See ethernet.txt file in the same directory +- rx-fifo-depth: See ethernet.txt file in the same directory +- snps,pbl Programmable Burst Length (tx and rx) +- snps,txpbl Tx Programmable Burst Length. Only for GMAC and newer. + If set, DMA tx will use this value rather than snps,pbl. +- snps,rxpbl Rx Programmable Burst Length. Only for GMAC and newer. + If set, DMA rx will use this value rather than snps,pbl. +- snps,no-pbl-x8 Don't multiply the pbl/txpbl/rxpbl values by 8. + For core rev < 3.50, don't multiply the values by 4. +- snps,aal Address-Aligned Beats +- snps,fixed-burst Program the DMA to use the fixed burst mode +- snps,mixed-burst Program the DMA to use the mixed burst mode +- snps,force_thresh_dma_mode Force DMA to use the threshold mode for + both tx and rx +- snps,force_sf_dma_mode Force DMA to use the Store and Forward + mode for both tx and rx. This flag is + ignored if force_thresh_dma_mode is set. +- snps,en-tx-lpi-clockgating Enable gating of the MAC TX clock during + TX low-power mode +- snps,multicast-filter-bins: Number of multicast filter hash bins + supported by this device instance +- snps,perfect-filter-entries: Number of perfect filter entries supported + by this device instance +- snps,ps-speed: port selection speed that can be passed to the core when + PCS is supported. For example, this is used in case of SGMII + and MAC2MAC connection. +- snps,tso: this enables the TSO feature otherwise it will be managed by + MAC HW capability register. Only for GMAC4 and newer. +- AXI BUS Mode parameters: below the list of all the parameters to program the + AXI register inside the DMA module: + - snps,lpi_en: enable Low Power Interface + - snps,xit_frm: unlock on WoL + - snps,wr_osr_lmt: max write outstanding req. limit + - snps,rd_osr_lmt: max read outstanding req. limit + - snps,kbbe: do not cross 1KiB boundary. + - snps,blen: this is a vector of supported burst length. + - snps,fb: fixed-burst + - snps,mb: mixed-burst + - snps,rb: rebuild INCRx Burst +- mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus. +- Multiple RX Queues parameters: below the list of all the parameters to + configure the multiple RX queues: + - snps,rx-queues-to-use: number of RX queues to be used in the driver + - Choose one of these RX scheduling algorithms: + - snps,rx-sched-sp: Strict priority + - snps,rx-sched-wsp: Weighted Strict priority + - For each RX queue + - Choose one of these modes: + - snps,dcb-algorithm: Queue to be enabled as DCB + - snps,avb-algorithm: Queue to be enabled as AVB + - snps,map-to-dma-channel: Channel to map + - Specifiy specific packet routing: + - snps,route-avcp: AV Untagged Control packets + - snps,route-ptp: PTP Packets + - snps,route-dcbcp: DCB Control Packets + - snps,route-up: Untagged Packets + - snps,route-multi-broad: Multicast & Broadcast Packets + - snps,priority: RX queue priority (Range: 0x0 to 0xF) +- Multiple TX Queues parameters: below the list of all the parameters to + configure the multiple TX queues: + - snps,tx-queues-to-use: number of TX queues to be used in the driver + - Choose one of these TX scheduling algorithms: + - snps,tx-sched-wrr: Weighted Round Robin + - snps,tx-sched-wfq: Weighted Fair Queuing + - snps,tx-sched-dwrr: Deficit Weighted Round Robin + - snps,tx-sched-sp: Strict priority + - For each TX queue + - snps,weight: TX queue weight (if using a DCB weight algorithm) + - Choose one of these modes: + - snps,dcb-algorithm: TX queue will be working in DCB + - snps,avb-algorithm: TX queue will be working in AVB + [Attention] Queue 0 is reserved for legacy traffic + and so no AVB is available in this queue. + - Configure Credit Base Shaper (if AVB Mode selected): + - snps,send_slope: enable Low Power Interface + - snps,idle_slope: unlock on WoL + - snps,high_credit: max write outstanding req. limit + - snps,low_credit: max read outstanding req. limit + - snps,priority: TX queue priority (Range: 0x0 to 0xF) +Examples: + + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <0xf>; + snps,rd_osr_lmt = <0xf>; + snps,blen = <256 128 64 32 0 0 0>; + }; + + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <1>; + snps,rx-sched-sp; + queue0 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + snps,priority = <0x0>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <2>; + snps,tx-sched-wrr; + queue0 { + snps,weight = <0x10>; + snps,dcb-algorithm; + snps,priority = <0x0>; + }; + + queue1 { + snps,avb-algorithm; + snps,send_slope = <0x1000>; + snps,idle_slope = <0x1000>; + snps,high_credit = <0x3E800>; + snps,low_credit = <0xFFC18000>; + snps,priority = <0x1>; + }; + }; + + gmac0: ethernet@e0800000 { + compatible = "st,spear600-gmac"; + reg = <0xe0800000 0x8000>; + interrupt-parent = <&vic1>; + interrupts = <24 23 22>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + mac-address = [000000000000]; /* Filled in by U-Boot */ + max-frame-size = <3800>; + phy-mode = "gmii"; + snps,multicast-filter-bins = <256>; + snps,perfect-filter-entries = <128>; + rx-fifo-depth = <16384>; + tx-fifo-depth = <16384>; + clocks = <&clock>; + clock-names = "stmmaceth"; + snps,axi-config = <&stmmac_axi_setup>; + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "snps,dwmac-mdio"; + phy1: ethernet-phy@0 { + }; + }; + snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; + }; diff --git a/Documentation/devicetree/bindings/net/ti,dp83867.txt b/Documentation/devicetree/bindings/net/ti,dp83867.txt new file mode 100644 index 000000000..9ef9338aa --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,dp83867.txt @@ -0,0 +1,48 @@ +* Texas Instruments - dp83867 Giga bit ethernet phy + +Required properties: + - reg - The ID number for the phy, usually a small integer + - ti,rx-internal-delay - RGMII Receive Clock Delay - see dt-bindings/net/ti-dp83867.h + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_RXID + - ti,tx-internal-delay - RGMII Transmit Clock Delay - see dt-bindings/net/ti-dp83867.h + for applicable values. Required only if interface type is + PHY_INTERFACE_MODE_RGMII_ID or PHY_INTERFACE_MODE_RGMII_TXID + - ti,fifo-depth - Transmitt FIFO depth- see dt-bindings/net/ti-dp83867.h + for applicable values + +Optional property: + - ti,min-output-impedance - MAC Interface Impedance control to set + the programmable output impedance to + minimum value (35 ohms). + - ti,max-output-impedance - MAC Interface Impedance control to set + the programmable output impedance to + maximum value (70 ohms). + - ti,dp83867-rxctrl-strap-quirk - This denotes the fact that the + board has RX_DV/RX_CTRL pin strapped in + mode 1 or 2. To ensure PHY operation, + there are specific actions that + software needs to take when this pin is + strapped in these modes. See data manual + for details. + - ti,clk-output-sel - Muxing option for CLK_OUT pin - see dt-bindings/net/ti-dp83867.h + for applicable values. + +Note: ti,min-output-impedance and ti,max-output-impedance are mutually + exclusive. When both properties are present ti,max-output-impedance + takes precedence. + +Default child nodes are standard Ethernet PHY device +nodes as described in Documentation/devicetree/bindings/net/phy.txt + +Example: + + ethernet-phy@0 { + reg = <0>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + }; + +Datasheet can be found: +http://www.ti.com/product/DP83867IR/datasheet diff --git a/Documentation/devicetree/bindings/net/ti-bluetooth.txt b/Documentation/devicetree/bindings/net/ti-bluetooth.txt new file mode 100644 index 000000000..6d03ff8c7 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti-bluetooth.txt @@ -0,0 +1,61 @@ +Texas Instruments Bluetooth Chips +--------------------------------- + +This documents the binding structure and common properties for serial +attached TI Bluetooth devices. The following chips are included in this +binding: + +* TI CC256x Bluetooth devices +* TI WiLink 7/8 (wl12xx/wl18xx) Shared Transport BT/FM/GPS devices + +TI WiLink devices have a UART interface for providing Bluetooth, FM radio, +and GPS over what's called "shared transport". The shared transport is +standard BT HCI protocol with additional channels for the other functions. + +TI WiLink devices also have a separate WiFi interface as described in +wireless/ti,wlcore.txt. + +This bindings follows the UART slave device binding in +../serial/slave-device.txt. + +Required properties: + - compatible: should be one of the following: + "ti,cc2560" + "ti,wl1271-st" + "ti,wl1273-st" + "ti,wl1281-st" + "ti,wl1283-st" + "ti,wl1285-st" + "ti,wl1801-st" + "ti,wl1805-st" + "ti,wl1807-st" + "ti,wl1831-st" + "ti,wl1835-st" + "ti,wl1837-st" + +Optional properties: + - enable-gpios : GPIO signal controlling enabling of BT. Active high. + - vio-supply : Vio input supply (1.8V) + - vbat-supply : Vbat input supply (2.9-4.8V) + - clocks : Must contain an entry, for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names : Must include the following entry: + "ext_clock" (External clock provided to the TI combo chip). + - nvmem-cells: phandle to nvmem data cell that contains a 6 byte BD address + with the most significant byte first (big-endian). + - nvmem-cell-names: "bd-address" (required when nvmem-cells is specified) + +Example: + +&serial0 { + compatible = "ns16550a"; + ... + bluetooth { + compatible = "ti,wl1835-st"; + enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + clocks = <&clk32k_wl18xx>; + clock-names = "ext_clock"; + nvmem-cells = <&bd_address>; + nvmem-cell-names = "bd-address"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/via-rhine.txt b/Documentation/devicetree/bindings/net/via-rhine.txt new file mode 100644 index 000000000..334eca2bf --- /dev/null +++ b/Documentation/devicetree/bindings/net/via-rhine.txt @@ -0,0 +1,17 @@ +* VIA Rhine 10/100 Network Controller + +Required properties: +- compatible : Should be "via,vt8500-rhine" for integrated + Rhine controllers found in VIA VT8500, WonderMedia WM8950 + and similar. These are listed as 1106:3106 rev. 0x84 on the + virtual PCI bus under vendor-provided kernels +- reg : Address and length of the io space +- interrupts : Should contain the controller interrupt line + +Examples: + +ethernet@d8004000 { + compatible = "via,vt8500-rhine"; + reg = <0xd8004000 0x100>; + interrupts = <10>; +}; diff --git a/Documentation/devicetree/bindings/net/via-velocity.txt b/Documentation/devicetree/bindings/net/via-velocity.txt new file mode 100644 index 000000000..b3db469b1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/via-velocity.txt @@ -0,0 +1,20 @@ +* VIA Velocity 10/100/1000 Network Controller + +Required properties: +- compatible : Should be "via,velocity-vt6110" +- reg : Address and length of the io space +- interrupts : Should contain the controller interrupt line + +Optional properties: +- no-eeprom : PCI network cards use an external EEPROM to store data. Embedded + devices quite often set this data in uboot and do not provide an eeprom. + Specify this option if you have no external eeprom. + +Examples: + +eth0@d8004000 { + compatible = "via,velocity-vt6110"; + reg = <0xd8004000 0x400>; + interrupts = <10>; + no-eeprom; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt new file mode 100644 index 000000000..cffb2d687 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt @@ -0,0 +1,38 @@ +Broadcom BCM43xx Fullmac wireless SDIO devices + +This node provides properties for controlling the Broadcom wireless device. The +node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + + - compatible : Should be "brcm,bcm4329-fmac". + +Optional properties: + - brcm,drive-strength : drive strength used for SDIO pins on device in mA + (default = 6). + - interrupts : specifies attributes for the out-of-band interrupt (host-wake). + When not specified the device will use in-band SDIO interrupts. + - interrupt-names : name of the out-of-band interrupt, which must be set + to "host-wake". + +Example: + +mmc3: mmc@1c12000 { + #address-cells = <1>; + #size-cells = <0>; + + pinctrl-names = "default"; + pinctrl-0 = <&mmc3_pins_a>; + vmmc-supply = <®_vmmc3>; + bus-width = <4>; + non-removable; + + brcmf: wifi@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + interrupt-parent = <&pio>; + interrupts = <10 8>; /* PH10 / EINT10 */ + interrupt-names = "host-wake"; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt new file mode 100644 index 000000000..6830c4786 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt @@ -0,0 +1,30 @@ +Espressif ESP8089 wireless SDIO devices + +This node provides properties for controlling the ESP8089 wireless device. +The node is expected to be specified as a child node to the SDIO controller +that connects the device to the system. + +Required properties: + + - compatible : Should be "esp,esp8089". + +Optional properties: + - esp,crystal-26M-en: Integer value for the crystal_26M_en firmware parameter + +Example: + +&mmc1 { + #address-cells = <1>; + #size-cells = <0>; + + vmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + + esp8089: sdio_wifi@1 { + compatible = "esp,esp8089"; + reg = <1>; + esp,crystal-26M-en = <2>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ieee80211.txt b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt new file mode 100644 index 000000000..f6442b139 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt @@ -0,0 +1,24 @@ +Common IEEE 802.11 properties + +This provides documentation of common properties that are valid for all wireless +devices. + +Optional properties: + - ieee80211-freq-limit : list of supported frequency ranges in KHz. This can be + used for devices that in a given config support less channels than + normally. It may happen chipset supports a wide wireless band but it is + limited to some part of it due to used antennas or power amplifier. + An example case for this can be tri-band wireless router with two + identical chipsets used for two different 5 GHz subbands. Using them + incorrectly could not work or decrease performance noticeably. + +Example: + +pcie@0,0 { + reg = <0x0000 0 0 0 0>; + wifi@0,0 { + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <2402000 2482000>, + <5170000 5250000>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt new file mode 100644 index 000000000..9bf9bbac1 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt @@ -0,0 +1,68 @@ +Marvell 8787/8897/8997 (sd8787/sd8897/sd8997/pcie8997) SDIO/PCIE devices +------ + +This node provides properties for controlling the Marvell SDIO/PCIE wireless device. +The node is expected to be specified as a child node to the SDIO/PCIE controller that +connects the device to the system. + +Required properties: + + - compatible : should be one of the following: + * "marvell,sd8787" + * "marvell,sd8897" + * "marvell,sd8997" + * "pci11ab,2b42" + * "pci1b4b,2b42" + +Optional properties: + + - marvell,caldata* : A series of properties with marvell,caldata prefix, + represent calibration data downloaded to the device during + initialization. This is an array of unsigned 8-bit values. + the properties should follow below property name and + corresponding array length: + "marvell,caldata-txpwrlimit-2g" (length = 566). + "marvell,caldata-txpwrlimit-5g-sub0" (length = 502). + "marvell,caldata-txpwrlimit-5g-sub1" (length = 688). + "marvell,caldata-txpwrlimit-5g-sub2" (length = 750). + "marvell,caldata-txpwrlimit-5g-sub3" (length = 502). + - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured + to firmware. Firmware will wakeup the host using this pin + during suspend/resume. + - interrupts : interrupt pin number to the cpu. driver will request an irq based on + this interrupt number. during system suspend, the irq will be enabled + so that the wifi chip can wakeup host platform under certain condition. + during system resume, the irq will be disabled to make sure + unnecessary interrupt is not received. + - vmmc-supply: a phandle of a regulator, supplying VCC to the card + - mmc-pwrseq: phandle to the MMC power sequence node. See "mmc-pwrseq-*" + for documentation of MMC power sequence bindings. + +Example: + +Tx power limit calibration data is configured in below example. +The calibration data is an array of unsigned values, the length +can vary between hw versions. +IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured +so that firmware can wakeup host using this device side pin. + +&mmc3 { + vmmc-supply = <&wlan_en_reg>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + mwifiex: wifi@1 { + compatible = "marvell,sd8897"; + reg = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_LOW>; + + marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 < + 0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>; + marvell,wakeup-pin = <3>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt new file mode 100644 index 000000000..0c17a0ec9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt @@ -0,0 +1,32 @@ +* MediaTek mt76xx devices + +This node provides properties for configuring the MediaTek mt76xx wireless +device. The node is expected to be specified as a child node of the PCI +controller to which the wireless chip is connected. + +Optional properties: + +- mac-address: See ethernet.txt in the parent directory +- local-mac-address: See ethernet.txt in the parent directory +- ieee80211-freq-limit: See ieee80211.txt +- mediatek,mtd-eeprom: Specify a MTD partition + offset containing EEPROM data + +Optional nodes: +- led: Properties for a connected LED + Optional properties: + - led-sources: See Documentation/devicetree/bindings/leds/common.txt + +&pcie { + pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + ieee80211-freq-limit = <5000000 6000000>; + mediatek,mtd-eeprom = <&factory 0x8000>; + + led { + led-sources = <2>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt new file mode 100644 index 000000000..b7396c8c2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt @@ -0,0 +1,48 @@ +* Qualcomm Atheros ath9k wireless devices + +This node provides properties for configuring the ath9k wireless device. The +node is expected to be specified as a child node of the PCI controller to +which the wireless chip is connected. + +Required properties: +- compatible: For PCI and PCIe devices this should be an identifier following + the format as defined in "PCI Bus Binding to Open Firmware" + Revision 2.1. One of the possible formats is "pciVVVV,DDDD" + where VVVV is the PCI vendor ID and DDDD is PCI device ID. + Typically QCA's PCI vendor ID 168c is used while the PCI device + ID depends on the chipset - see the following (possibly + incomplete) list: + - 0023 for AR5416 + - 0024 for AR5418 + - 0027 for AR9160 + - 0029 for AR9220 and AR9223 + - 002a for AR9280 and AR9283 + - 002b for AR9285 + - 002c for AR2427 + - 002d for AR9227 + - 002e for AR9287 + - 0030 for AR9380, AR9381 and AR9382 + - 0032 for AR9485 + - 0033 for AR9580 and AR9590 + - 0034 for AR9462 + - 0036 for AR9565 + - 0037 for AR9485 +- reg: Address and length of the register set for the device. + +Optional properties: +- qca,no-eeprom: Indicates that there is no physical EEPROM connected to the + ath9k wireless chip (in this case the calibration / + EEPROM data will be loaded from userspace using the + kernel firmware loader). +- mac-address: See ethernet.txt in the parent directory +- local-mac-address: See ethernet.txt in the parent directory + + +In this example, the node is defined as child node of the PCI controller: +&pci0 { + wifi@168c,002d { + compatible = "pci168c,002d"; + reg = <0x7000 0 0 0 0x1000>; + qca,no-eeprom; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt new file mode 100644 index 000000000..7fd4e8ce4 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -0,0 +1,152 @@ +* Qualcomm Atheros ath10k wireless devices + +Required properties: +- compatible: Should be one of the following: + * "qcom,ath10k" + * "qcom,ipq4019-wifi" + * "qcom,wcn3990-wifi" + +PCI based devices uses compatible string "qcom,ath10k" and takes calibration +data along with board specific data via "qcom,ath10k-calibration-data". +Rest of the properties are not applicable for PCI based devices. + +AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi" +and also uses most of the properties defined in this doc (except +"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data" +to carry pre calibration data. + +In general, entry "qcom,ath10k-pre-calibration-data" and +"qcom,ath10k-calibration-data" conflict with each other and only one +can be provided per device. + +SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi". + +Optional properties: +- reg: Address and length of the register set for the device. +- reg-names: Must include the list of following reg names, + "membase" +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reseti.txt for details. +- reset-names: Must include the list of following reset names, + "wifi_cpu_init" + "wifi_radio_srif" + "wifi_radio_warm" + "wifi_radio_cold" + "wifi_core_warm" + "wifi_core_cold" +- clocks: List of clock specifiers, must contain an entry for each required + entry in clock-names. +- clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref", + "wifi_wcss_rtc". +- interrupts: List of interrupt lines. Must contain an entry + for each entry in the interrupt-names property. +- interrupt-names: Must include the entries for MSI interrupt + names ("msi0" to "msi15") and legacy interrupt + name ("legacy"), +- qcom,msi_addr: MSI interrupt address. +- qcom,msi_base: Base value to add before writing MSI data into + MSI address register. +- qcom,ath10k-calibration-variant: string to search for in the board-2.bin + variant list with the same bus and device + specific ids +- qcom,ath10k-calibration-data : calibration data + board specific data + as an array, the length can vary between + hw versions. +- qcom,ath10k-pre-calibration-data : pre calibration data as an array, + the length can vary between hw versions. +- <supply-name>-supply: handle to the regulator device tree node + optional "supply-name" is "vdd-0.8-cx-mx". + +Example (to supply the calibration data alone): + +In this example, the node is defined as child node of the PCI controller. + +pci { + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + ath10k@0,0 { + reg = <0 0 0 0 0>; + device_type = "pci"; + qcom,ath10k-calibration-data = [ 01 02 03 ... ]; + }; + }; +}; + +Example (to supply ipq4019 SoC wifi block details): + +wifi0: wifi@a000000 { + compatible = "qcom,ipq4019-wifi"; + reg = <0xa000000 0x200000>; + resets = <&gcc WIFI0_CPU_INIT_RESET>, + <&gcc WIFI0_RADIO_SRIF_RESET>, + <&gcc WIFI0_RADIO_WARM_RESET>, + <&gcc WIFI0_RADIO_COLD_RESET>, + <&gcc WIFI0_CORE_WARM_RESET>, + <&gcc WIFI0_CORE_COLD_RESET>; + reset-names = "wifi_cpu_init", + "wifi_radio_srif", + "wifi_radio_warm", + "wifi_radio_cold", + "wifi_core_warm", + "wifi_core_cold"; + clocks = <&gcc GCC_WCSS2G_CLK>, + <&gcc GCC_WCSS2G_REF_CLK>, + <&gcc GCC_WCSS2G_RTC_CLK>; + clock-names = "wifi_wcss_cmd", + "wifi_wcss_ref", + "wifi_wcss_rtc"; + interrupts = <0 0x20 0x1>, + <0 0x21 0x1>, + <0 0x22 0x1>, + <0 0x23 0x1>, + <0 0x24 0x1>, + <0 0x25 0x1>, + <0 0x26 0x1>, + <0 0x27 0x1>, + <0 0x28 0x1>, + <0 0x29 0x1>, + <0 0x2a 0x1>, + <0 0x2b 0x1>, + <0 0x2c 0x1>, + <0 0x2d 0x1>, + <0 0x2e 0x1>, + <0 0x2f 0x1>, + <0 0xa8 0x0>; + interrupt-names = "msi0", "msi1", "msi2", "msi3", + "msi4", "msi5", "msi6", "msi7", + "msi8", "msi9", "msi10", "msi11", + "msi12", "msi13", "msi14", "msi15", + "legacy"; + qcom,msi_addr = <0x0b006040>; + qcom,msi_base = <0x40>; + qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; +}; + +Example (to supply wcn3990 SoC wifi block details): + +wifi@18000000 { + compatible = "qcom,wcn3990-wifi"; + reg = <0x18800000 0x800000>; + reg-names = "membase"; + clocks = <&clock_gcc clk_aggre2_noc_clk>; + clock-names = "smmu_aggre2_noc_clk" + interrupts = + <0 130 0 /* CE0 */ >, + <0 131 0 /* CE1 */ >, + <0 132 0 /* CE2 */ >, + <0 133 0 /* CE3 */ >, + <0 134 0 /* CE4 */ >, + <0 135 0 /* CE5 */ >, + <0 136 0 /* CE6 */ >, + <0 137 0 /* CE7 */ >, + <0 138 0 /* CE8 */ >, + <0 139 0 /* CE9 */ >, + <0 140 0 /* CE10 */ >, + <0 141 0 /* CE11 */ >; + vdd-0.8-cx-mx-supply = <&pm8998_l5>; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt new file mode 100644 index 000000000..bb2fcde6f --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt @@ -0,0 +1,37 @@ +* Texas Instruments wl1251 wireless lan controller + +The wl1251 chip can be connected via SPI or via SDIO. This +document describes the binding for the SPI connected chip. + +Required properties: +- compatible : Should be "ti,wl1251" +- reg : Chip select address of device +- spi-max-frequency : Maximum SPI clocking speed of device in Hz +- interrupts : Should contain interrupt line +- vio-supply : phandle to regulator providing VIO +- ti,power-gpio : GPIO connected to chip's PMEN pin + +Optional properties: +- ti,wl1251-has-eeprom : boolean, the wl1251 has an eeprom connected, which + provides configuration data (calibration, MAC, ...) +- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt + for optional SPI connection related properties, + +Examples: + +&spi1 { + wl1251@0 { + compatible = "ti,wl1251"; + + reg = <0>; + spi-max-frequency = <48000000>; + spi-cpol; + spi-cpha; + + interrupt-parent = <&gpio2>; + interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */ + + vio-supply = <&vio>; + ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */ + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt new file mode 100644 index 000000000..cb5c9e156 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt @@ -0,0 +1,57 @@ +* Texas Instruments wl12xx/wl18xx wireless lan controller + +The wl12xx/wl18xx chips can be connected via SPI or via SDIO. This +document describes the binding for the SPI connected chip. + +Required properties: +- compatible : Should be one of the following: + * "ti,wl1271" + * "ti,wl1273" + * "ti,wl1281" + * "ti,wl1283" + * "ti,wl1801" + * "ti,wl1805" + * "ti,wl1807" + * "ti,wl1831" + * "ti,wl1835" + * "ti,wl1837" +- reg : Chip select address of device +- spi-max-frequency : Maximum SPI clocking speed of device in Hz +- interrupts : Should contain parameters for 1 interrupt line. +- vwlan-supply : Point the node of the regulator that powers/enable the + wl12xx/wl18xx chip + +Optional properties: +- ref-clock-frequency : Reference clock frequency (should be set for wl12xx) +- clock-xtal : boolean, clock is generated from XTAL + +- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt + for optional SPI connection related properties, + +Examples: + +For wl12xx family: +&spi1 { + wlcore: wlcore@1 { + compatible = "ti,wl1271"; + reg = <1>; + spi-max-frequency = <48000000>; + interrupt-parent = <&gpio3>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; + vwlan-supply = <&vwlan_fixed>; + clock-xtal; + ref-clock-frequency = <38400000>; + }; +}; + +For wl18xx family: +&spi0 { + wlcore: wlcore@0 { + compatible = "ti,wl1835"; + reg = <0>; + spi-max-frequency = <48000000>; + interrupt-parent = <&gpio0>; + interrupts = <27 IRQ_TYPE_EDGE_RISING>; + vwlan-supply = <&vwlan_fixed>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt new file mode 100644 index 000000000..9306c4dad --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt @@ -0,0 +1,45 @@ +TI Wilink 6/7/8 (wl12xx/wl18xx) SDIO devices + +This node provides properties for controlling the wilink wireless device. The +node is expected to be specified as a child node to the SDIO controller that +connects the device to the system. + +Required properties: + - compatible: should be one of the following: + * "ti,wl1271" + * "ti,wl1273" + * "ti,wl1281" + * "ti,wl1283" + * "ti,wl1285" + * "ti,wl1801" + * "ti,wl1805" + * "ti,wl1807" + * "ti,wl1831" + * "ti,wl1835" + * "ti,wl1837" + - interrupts : specifies attributes for the out-of-band interrupt. + +Optional properties: + - ref-clock-frequency : ref clock frequency in Hz + - tcxo-clock-frequency : tcxo clock frequency in Hz + +Note: the *-clock-frequency properties assume internal clocks. In case of external +clock, new bindings (for parsing the clock nodes) have to be added. + +Example: + +&mmc3 { + vmmc-supply = <&wlan_en_reg>; + bus-width = <4>; + cap-power-off-card; + keep-power-in-suspend; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1835"; + reg = <2>; + interrupt-parent = <&gpio0>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt new file mode 100644 index 000000000..38f9ec076 --- /dev/null +++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt @@ -0,0 +1,55 @@ +XILINX AXI ETHERNET Device Tree Bindings +-------------------------------------------------------- + +Also called AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core +provides connectivity to an external ethernet PHY supporting different +interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two +segments of memory for buffering TX and RX, as well as the capability of +offloading TX/RX checksum calculation off the processor. + +Management configuration is done through the AXI interface, while payload is +sent and received through means of an AXI DMA controller. This driver +includes the DMA driver code, so this driver is incompatible with AXI DMA +driver. + +For more details about mdio please refer phy.txt file in the same directory. + +Required properties: +- compatible : Must be one of "xlnx,axi-ethernet-1.00.a", + "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a" +- reg : Address and length of the IO space. +- interrupts : Should be a list of two interrupt, TX and RX. +- phy-handle : Should point to the external phy device. + See ethernet.txt file in the same directory. +- xlnx,rxmem : Set to allocated memory buffer for Rx/Tx in the hardware + +Optional properties: +- phy-mode : See ethernet.txt +- xlnx,phy-type : Deprecated, do not use, but still accepted in preference + to phy-mode. +- xlnx,txcsum : 0 or empty for disabling TX checksum offload, + 1 to enable partial TX checksum offload, + 2 to enable full TX checksum offload +- xlnx,rxcsum : Same values as xlnx,txcsum but for RX checksum offload + +Example: + axi_ethernet_eth: ethernet@40c00000 { + compatible = "xlnx,axi-ethernet-1.00.a"; + device_type = "network"; + interrupt-parent = <µblaze_0_axi_intc>; + interrupts = <2 0>; + phy-mode = "mii"; + reg = <0x40c00000 0x40000>; + xlnx,rxcsum = <0x2>; + xlnx,rxmem = <0x800>; + xlnx,txcsum = <0x2>; + phy-handle = <&phy0>; + axi_ethernetlite_0_mdio: mdio { + #address-cells = <1>; + #size-cells = <0>; + phy0: phy@0 { + device_type = "ethernet-phy"; + reg = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/xilinx_gmii2rgmii.txt b/Documentation/devicetree/bindings/net/xilinx_gmii2rgmii.txt new file mode 100644 index 000000000..038dda48b --- /dev/null +++ b/Documentation/devicetree/bindings/net/xilinx_gmii2rgmii.txt @@ -0,0 +1,35 @@ +XILINX GMIITORGMII Converter Driver Device Tree Bindings +-------------------------------------------------------- + +The Gigabit Media Independent Interface (GMII) to Reduced Gigabit Media +Independent Interface (RGMII) core provides the RGMII between RGMII-compliant +Ethernet physical media devices (PHY) and the Gigabit Ethernet controller. +This core can be used in all three modes of operation(10/100/1000 Mb/s). +The Management Data Input/Output (MDIO) interface is used to configure the +Speed of operation. This core can switch dynamically between the three +Different speed modes by configuring the conveter register through mdio write. + +This converter sits between the ethernet MAC and the external phy. +MAC <==> GMII2RGMII <==> RGMII_PHY + +For more details about mdio please refer phy.txt file in the same directory. + +Required properties: +- compatible : Should be "xlnx,gmii-to-rgmii-1.0" +- reg : The ID number for the phy, usually a small integer +- phy-handle : Should point to the external phy device. + See ethernet.txt file in the same directory. + +Example: + mdio { + #address-cells = <1>; + #size-cells = <0>; + phy: ethernet-phy@0 { + ...... + }; + gmiitorgmii: gmiitorgmii@8 { + compatible = "xlnx,gmii-to-rgmii-1.0"; + reg = <8>; + phy-handle = <&phy>; + }; + }; |