diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt | 380 |
1 files changed, 380 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt new file mode 100644 index 000000000..70659c917 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt @@ -0,0 +1,380 @@ +Samsung GPIO and Pin Mux/Config controller + +Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware +controller. It controls the input/output settings on the available pads/pins +and also provides ability to multiplex and configure the output of various +on-chip controllers onto these pads. + +Required Properties: +- compatible: should be one of the following. + - "samsung,s3c2412-pinctrl": for S3C2412-compatible pin-controller, + - "samsung,s3c2416-pinctrl": for S3C2416-compatible pin-controller, + - "samsung,s3c2440-pinctrl": for S3C2440-compatible pin-controller, + - "samsung,s3c2450-pinctrl": for S3C2450-compatible pin-controller, + - "samsung,s3c64xx-pinctrl": for S3C64xx-compatible pin-controller, + - "samsung,s5pv210-pinctrl": for S5PV210-compatible pin-controller, + - "samsung,exynos3250-pinctrl": for Exynos3250 compatible pin-controller. + - "samsung,exynos4210-pinctrl": for Exynos4210 compatible pin-controller. + - "samsung,exynos4x12-pinctrl": for Exynos4x12 compatible pin-controller. + - "samsung,exynos5250-pinctrl": for Exynos5250 compatible pin-controller. + - "samsung,exynos5260-pinctrl": for Exynos5260 compatible pin-controller. + - "samsung,exynos5410-pinctrl": for Exynos5410 compatible pin-controller. + - "samsung,exynos5420-pinctrl": for Exynos5420 compatible pin-controller. + - "samsung,exynos5433-pinctrl": for Exynos5433 compatible pin-controller. + - "samsung,exynos7-pinctrl": for Exynos7 compatible pin-controller. + +- reg: Base address of the pin controller hardware module and length of + the address space it occupies. + + - reg: Second base address of the pin controller if the specific registers + of the pin controller are separated into the different base address. + + Eg: GPF[1-5] of Exynos5433 are separated into the two base address. + - First base address is for GPAx and GPF[1-5] external interrupt + registers. + - Second base address is for GPF[1-5] pinctrl registers. + + pinctrl_0: pinctrl@10580000 { + compatible = "samsung,exynos5433-pinctrl"; + reg = <0x10580000 0x1a20>, <0x11090000 0x100>; + + wakeup-interrupt-controller { + compatible = "samsung,exynos7-wakeup-eint"; + interrupts = <0 16 0>; + }; + }; + +- Pin banks as child nodes: Pin banks of the controller are represented by child + nodes of the controller node. Bank name is taken from name of the node. Each + bank node must contain following properties: + + - gpio-controller: identifies the node as a gpio controller and pin bank. + - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO + binding is used, the amount of cells must be specified as 2. See the below + mentioned gpio binding representation for description of particular cells. + + Eg: <&gpx2 6 0> + <[phandle of the gpio controller node] + [pin number within the gpio controller] + [flags]> + + Values for gpio specifier: + - Pin number: is a value between 0 to 7. + - Flags: 0 - Active High + 1 - Active Low + +- Pin mux/config groups as child nodes: The pin mux (selecting pin function + mode) and pin config (pull up/down, driver strength) settings are represented + as child nodes of the pin-controller node. There should be atleast one + child node and there is no limit on the count of these child nodes. It is + also possible for a child node to consist of several further child nodes + to allow grouping multiple pinctrl groups into one. The format of second + level child nodes is exactly the same as for first level ones and is + described below. + + The child node should contain a list of pin(s) on which a particular pin + function selection or pin configuration (or both) have to applied. This + list of pins is specified using the property name "samsung,pins". There + should be atleast one pin specfied for this property and there is no upper + limit on the count of pins that can be specified. The pins are specified + using pin names which are derived from the hardware manual of the SoC. As + an example, the pins in GPA0 bank of the pin controller can be represented + as "gpa0-0", "gpa0-1", "gpa0-2" and so on. The names should be in lower case. + The format of the pin names should be (as per the hardware manual) + "[pin bank name]-[pin number within the bank]". + + The pin function selection that should be applied on the pins listed in the + child node is specified using the "samsung,pin-function" property. The value + of this property that should be applied to each of the pins listed in the + "samsung,pins" property should be picked from the hardware manual of the SoC + for the specified pin group. This property is optional in the child node if + no specific function selection is desired for the pins listed in the child + node. The value of this property is used as-is to program the pin-controller + function selector register of the pin-bank. + + The child node can also optionally specify one or more of the pin + configuration that should be applied on all the pins listed in the + "samsung,pins" property of the child node. The following pin configuration + properties are supported. + + - samsung,pin-val: Initial value of pin output buffer. + - samsung,pin-pud: Pull up/down configuration. + - samsung,pin-drv: Drive strength configuration. + - samsung,pin-pud-pdn: Pull up/down configuration in power down mode. + - samsung,pin-drv-pdn: Drive strength configuration in power down mode. + + The values specified by these config properties should be derived from the + hardware manual and these values are programmed as-is into the pin + pull up/down and driver strength register of the pin-controller. + + Note: A child should include atleast a pin function selection property or + pin configuration property (one or more) or both. + + The client nodes that require a particular pin function selection and/or + pin configuration should use the bindings listed in the "pinctrl-bindings.txt" + file. + +External GPIO and Wakeup Interrupts: + +The controller supports two types of external interrupts over gpio. The first +is the external gpio interrupt and second is the external wakeup interrupts. +The difference between the two is that the external wakeup interrupts can be +used as system wakeup events. + +A. External GPIO Interrupts: For supporting external gpio interrupts, the + following properties should be specified in the pin-controller device node. + + - interrupts: interrupt specifier for the controller. The format and value of + the interrupt specifier depends on the interrupt parent for the controller. + + In addition, following properties must be present in node of every bank + of pins supporting GPIO interrupts: + + - interrupt-controller: identifies the controller node as interrupt-parent. + - #interrupt-cells: the value of this property should be 2. + - First Cell: represents the external gpio interrupt number local to the + external gpio interrupt space of the controller. + - Second Cell: flags to identify the type of the interrupt + - 1 = rising edge triggered + - 2 = falling edge triggered + - 3 = rising and falling edge triggered + - 4 = high level triggered + - 8 = low level triggered + +B. External Wakeup Interrupts: For supporting external wakeup interrupts, a + child node representing the external wakeup interrupt controller should be + included in the pin-controller device node. + + Only one pin-controller device node can include external wakeup interrupts + child node (in other words, only one External Wakeup Interrupts + pin-controller is supported). + + This child node should include following properties: + + - compatible: identifies the type of the external wakeup interrupt controller + The possible values are: + - samsung,s3c2410-wakeup-eint: represents wakeup interrupt controller + found on Samsung S3C24xx SoCs except S3C2412 and S3C2413, + - samsung,s3c2412-wakeup-eint: represents wakeup interrupt controller + found on Samsung S3C2412 and S3C2413 SoCs, + - samsung,s3c64xx-wakeup-eint: represents wakeup interrupt controller + found on Samsung S3C64xx SoCs, + - samsung,s5pv210-wakeup-eint: represents wakeup interrupt controller + found on Samsung S5Pv210 SoCs, + - samsung,exynos4210-wakeup-eint: represents wakeup interrupt controller + found on Samsung Exynos4210 and S5PC110/S5PV210 SoCs. + - samsung,exynos7-wakeup-eint: represents wakeup interrupt controller + found on Samsung Exynos7 SoC. + - interrupts: interrupt used by multiplexed wakeup interrupts. + + In addition, following properties must be present in node of every bank + of pins supporting wake-up interrupts: + + - interrupt-controller: identifies the node as interrupt-parent. + - #interrupt-cells: the value of this property should be 2 + - First Cell: represents the external wakeup interrupt number local to + the external wakeup interrupt space of the controller. + - Second Cell: flags to identify the type of the interrupt + - 1 = rising edge triggered + - 2 = falling edge triggered + - 3 = rising and falling edge triggered + - 4 = high level triggered + - 8 = low level triggered + + Node of every bank of pins supporting direct wake-up interrupts (without + multiplexing) must contain following properties: + + - interrupts: interrupts of the interrupt parent which are used for external + wakeup interrupts from pins of the bank, must contain interrupts for all + pins of the bank. + +Aliases: + +All the pin controller nodes should be represented in the aliases node using +the following format 'pinctrl{n}' where n is a unique number for the alias. + +Aliases for controllers compatible with "samsung,exynos7-pinctrl": +- pinctrl0: pin controller of ALIVE block, +- pinctrl1: pin controller of BUS0 block, +- pinctrl2: pin controller of NFC block, +- pinctrl3: pin controller of TOUCH block, +- pinctrl4: pin controller of FF block, +- pinctrl5: pin controller of ESE block, +- pinctrl6: pin controller of FSYS0 block, +- pinctrl7: pin controller of FSYS1 block, +- pinctrl8: pin controller of BUS1 block, +- pinctrl9: pin controller of AUDIO block, + +Example: A pin-controller node with pin banks: + + pinctrl_0: pinctrl@11400000 { + compatible = "samsung,exynos4210-pinctrl"; + reg = <0x11400000 0x1000>; + interrupts = <0 47 0>; + + /* ... */ + + /* Pin bank without external interrupts */ + gpy0: gpy0 { + gpio-controller; + #gpio-cells = <2>; + }; + + /* ... */ + + /* Pin bank with external GPIO or muxed wake-up interrupts */ + gpj0: gpj0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + /* ... */ + + /* Pin bank with external direct wake-up interrupts */ + gpx0: gpx0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + interrupt-parent = <&gic>; + interrupts = <0 16 0>, <0 17 0>, <0 18 0>, <0 19 0>, + <0 20 0>, <0 21 0>, <0 22 0>, <0 23 0>; + #interrupt-cells = <2>; + }; + + /* ... */ + }; + +Example 1: A pin-controller node with pin groups. + + #include <dt-bindings/pinctrl/samsung.h> + + pinctrl_0: pinctrl@11400000 { + compatible = "samsung,exynos4210-pinctrl"; + reg = <0x11400000 0x1000>; + interrupts = <0 47 0>; + + /* ... */ + + uart0_data: uart0-data { + samsung,pins = "gpa0-0", "gpa0-1"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + uart0_fctl: uart0-fctl { + samsung,pins = "gpa0-2", "gpa0-3"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + uart1_data: uart1-data { + samsung,pins = "gpa0-4", "gpa0-5"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + uart1_fctl: uart1-fctl { + samsung,pins = "gpa0-6", "gpa0-7"; + samsung,pin-function = <EXYNOS_PIN_FUNC_2>; + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + i2c2_bus: i2c2-bus { + samsung,pins = "gpa0-6", "gpa0-7"; + samsung,pin-function = <EXYNOS_PIN_FUNC_3>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>; + }; + + sd4_bus8: sd4-bus-width8 { + part-1 { + samsung,pins = "gpk0-3", "gpk0-4", + "gpk0-5", "gpk0-6"; + samsung,pin-function = <EXYNOS_PIN_FUNC_3>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; + }; + part-2 { + samsung,pins = "gpk1-3", "gpk1-4", + "gpk1-5", "gpk1-6"; + samsung,pin-function = <EXYNOS_PIN_FUNC_4>; + samsung,pin-pud = <EXYNOS_PIN_PULL_UP>; + samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>; + }; + }; + }; + +Example 2: A pin-controller node with external wakeup interrupt controller node. + + pinctrl_1: pinctrl@11000000 { + compatible = "samsung,exynos4210-pinctrl"; + reg = <0x11000000 0x1000>; + interrupts = <0 46 0> + + /* ... */ + + wakeup-interrupt-controller { + compatible = "samsung,exynos4210-wakeup-eint"; + interrupt-parent = <&gic>; + interrupts = <0 32 0>; + }; + }; + +Example 3: A uart client node that supports 'default' and 'flow-control' states. + + uart@13800000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x13800000 0x100>; + interrupts = <0 52 0>; + pinctrl-names = "default", "flow-control; + pinctrl-0 = <&uart0_data>; + pinctrl-1 = <&uart0_data &uart0_fctl>; + }; + +Example 4: Set up the default pin state for uart controller. + + static int s3c24xx_serial_probe(struct platform_device *pdev) { + struct pinctrl *pinctrl; + + /* ... */ + + pinctrl = devm_pinctrl_get_select_default(&pdev->dev); + } + +Example 5: A display port client node that supports 'default' pinctrl state + and gpio binding. + + display-port-controller { + /* ... */ + + samsung,hpd-gpio = <&gpx2 6 0>; + pinctrl-names = "default"; + pinctrl-0 = <&dp_hpd>; + }; + +Example 6: Request the gpio for display port controller + + static int exynos_dp_probe(struct platform_device *pdev) + { + int hpd_gpio, ret; + struct device *dev = &pdev->dev; + struct device_node *dp_node = dev->of_node; + + /* ... */ + + hpd_gpio = of_get_named_gpio(dp_node, "samsung,hpd-gpio", 0); + + /* ... */ + + ret = devm_gpio_request_one(&pdev->dev, hpd_gpio, GPIOF_IN, + "hpd_gpio"); + /* ... */ + } |