diff options
Diffstat (limited to 'Documentation/devicetree/bindings/ufs')
4 files changed, 200 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt b/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt new file mode 100644 index 000000000..71c077796 --- /dev/null +++ b/Documentation/devicetree/bindings/ufs/tc-dwc-g210-pltfrm.txt @@ -0,0 +1,26 @@ +* Universal Flash Storage (UFS) DesignWare Host Controller + +DWC_UFS nodes are defined to describe on-chip UFS host controllers and MPHY. +Each UFS controller instance should have its own node. + +Required properties: +- compatible : compatible list must contain the PHY type & version: + "snps,g210-tc-6.00-20bit" + "snps,g210-tc-6.00-40bit" + complemented with the Controller IP version: + "snps,dwc-ufshcd-1.40a" + complemented with the JEDEC version: + "jedec,ufs-1.1" + "jedec,ufs-2.0" + +- reg : <registers mapping> +- interrupts : <interrupt mapping for UFS host controller IRQ> + +Example for a setup using a 1.40a DWC Controller with a 6.00 G210 40-bit TC: + dwc-ufs@d0000000 { + compatible = "snps,g210-tc-6.00-40bit", + "snps,dwc-ufshcd-1.40a", + "jedec,ufs-2.0"; + reg = < 0xd0000000 0x10000 >; + interrupts = < 24 >; + }; diff --git a/Documentation/devicetree/bindings/ufs/ufs-hisi.txt b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt new file mode 100644 index 000000000..a48c44817 --- /dev/null +++ b/Documentation/devicetree/bindings/ufs/ufs-hisi.txt @@ -0,0 +1,41 @@ +* Hisilicon Universal Flash Storage (UFS) Host Controller + +UFS nodes are defined to describe on-chip UFS hardware macro. +Each UFS Host Controller should have its own node. + +Required properties: +- compatible : compatible list, contains one of the following - + "hisilicon,hi3660-ufs", "jedec,ufs-1.1" for hisi ufs + host controller present on Hi36xx chipset. +- reg : should contain UFS register address space & UFS SYS CTRL register address, +- interrupt-parent : interrupt device +- interrupts : interrupt number +- clocks : List of phandle and clock specifier pairs +- clock-names : List of clock input name strings sorted in the same + order as the clocks property. "ref_clk", "phy_clk" is optional +- freq-table-hz : Array of <min max> operating frequencies stored in the same + order as the clocks property. If this property is not + defined or a value in the array is "0" then it is assumed + that the frequency is set by the parent clock or a + fixed rate clock source. +- resets : describe reset node register +- reset-names : reset node register, the "rst" corresponds to reset the whole UFS IP. + +Example: + + ufs: ufs@ff3b0000 { + compatible = "hisilicon,hi3660-ufs", "jedec,ufs-1.1"; + /* 0: HCI standard */ + /* 1: UFS SYS CTRL */ + reg = <0x0 0xff3b0000 0x0 0x1000>, + <0x0 0xff3b1000 0x0 0x1000>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>, + <&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>; + clock-names = "ref_clk", "phy_clk"; + freq-table-hz = <0 0>, <0 0>; + /* offset: 0x84; bit: 12 */ + resets = <&crg_rst 0x84 12>; + reset-names = "rst"; + }; diff --git a/Documentation/devicetree/bindings/ufs/ufs-qcom.txt b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt new file mode 100644 index 000000000..21d9a93db --- /dev/null +++ b/Documentation/devicetree/bindings/ufs/ufs-qcom.txt @@ -0,0 +1,60 @@ +* Qualcomm Technologies Inc Universal Flash Storage (UFS) PHY + +UFSPHY nodes are defined to describe on-chip UFS PHY hardware macro. +Each UFS PHY node should have its own node. + +To bind UFS PHY with UFS host controller, the controller node should +contain a phandle reference to UFS PHY node. + +Required properties: +- compatible : compatible list, contains one of the following - + "qcom,ufs-phy-qmp-20nm" for 20nm ufs phy, + "qcom,ufs-phy-qmp-14nm" for legacy 14nm ufs phy, + "qcom,msm8996-ufs-phy-qmp-14nm" for 14nm ufs phy + present on MSM8996 chipset. +- reg : should contain PHY register address space (mandatory), +- reg-names : indicates various resources passed to driver (via reg proptery) by name. + Required "reg-names" is "phy_mem". +- #phy-cells : This property shall be set to 0 +- vdda-phy-supply : phandle to main PHY supply for analog domain +- vdda-pll-supply : phandle to PHY PLL and Power-Gen block power supply +- clocks : List of phandle and clock specifier pairs +- clock-names : List of clock input name strings sorted in the same + order as the clocks property. "ref_clk_src", "ref_clk", + "tx_iface_clk" & "rx_iface_clk" are mandatory but + "ref_clk_parent" is optional + +Optional properties: +- vdda-phy-max-microamp : specifies max. load that can be drawn from phy supply +- vdda-pll-max-microamp : specifies max. load that can be drawn from pll supply +- vddp-ref-clk-supply : phandle to UFS device ref_clk pad power supply +- vddp-ref-clk-max-microamp : specifies max. load that can be drawn from this supply + +Example: + + ufsphy1: ufsphy@fc597000 { + compatible = "qcom,ufs-phy-qmp-20nm"; + reg = <0xfc597000 0x800>; + reg-names = "phy_mem"; + #phy-cells = <0>; + vdda-phy-supply = <&pma8084_l4>; + vdda-pll-supply = <&pma8084_l12>; + vdda-phy-max-microamp = <50000>; + vdda-pll-max-microamp = <1000>; + clock-names = "ref_clk_src", + "ref_clk_parent", + "ref_clk", + "tx_iface_clk", + "rx_iface_clk"; + clocks = <&clock_rpm clk_ln_bb_clk>, + <&clock_gcc clk_pcie_1_phy_ldo >, + <&clock_gcc clk_ufs_phy_ldo>, + <&clock_gcc clk_gcc_ufs_tx_cfg_clk>, + <&clock_gcc clk_gcc_ufs_rx_cfg_clk>; + }; + + ufshc@fc598000 { + ... + phys = <&ufsphy1>; + phy-names = "ufsphy"; + }; diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt new file mode 100644 index 000000000..2df00524b --- /dev/null +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -0,0 +1,73 @@ +* Universal Flash Storage (UFS) Host Controller + +UFSHC nodes are defined to describe on-chip UFS host controllers. +Each UFS controller instance should have its own node. + +Required properties: +- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0", may + also list one or more of the following: + "qcom,msm8994-ufshc" + "qcom,msm8996-ufshc" + "qcom,ufshc" +- interrupts : <interrupt mapping for UFS host controller IRQ> +- reg : <registers mapping> + +Optional properties: +- phys : phandle to UFS PHY node +- phy-names : the string "ufsphy" when is found in a node, along + with "phys" attribute, provides phandle to UFS PHY node +- vdd-hba-supply : phandle to UFS host controller supply regulator node +- vcc-supply : phandle to VCC supply regulator node +- vccq-supply : phandle to VCCQ supply regulator node +- vccq2-supply : phandle to VCCQ2 supply regulator node +- vcc-supply-1p8 : For embedded UFS devices, valid VCC range is 1.7-1.95V + or 2.7-3.6V. This boolean property when set, specifies + to use low voltage range of 1.7-1.95V. Note for external + UFS cards this property is invalid and valid VCC range is + always 2.7-3.6V. +- vcc-max-microamp : specifies max. load that can be drawn from vcc supply +- vccq-max-microamp : specifies max. load that can be drawn from vccq supply +- vccq2-max-microamp : specifies max. load that can be drawn from vccq2 supply +- <name>-fixed-regulator : boolean property specifying that <name>-supply is a fixed regulator + +- clocks : List of phandle and clock specifier pairs +- clock-names : List of clock input name strings sorted in the same + order as the clocks property. +- freq-table-hz : Array of <min max> operating frequencies stored in the same + order as the clocks property. If this property is not + defined or a value in the array is "0" then it is assumed + that the frequency is set by the parent clock or a + fixed rate clock source. +-lanes-per-direction : number of lanes available per direction - either 1 or 2. + Note that it is assume same number of lanes is used both + directions at once. If not specified, default is 2 lanes per direction. +- resets : reset node register +- reset-names : describe reset node register, the "rst" corresponds to reset the whole UFS IP. + +Note: If above properties are not defined it can be assumed that the supply +regulators or clocks are always on. + +Example: + ufshc@fc598000 { + compatible = "jedec,ufs-1.1"; + reg = <0xfc598000 0x800>; + interrupts = <0 28 0>; + + vdd-hba-supply = <&xxx_reg0>; + vdd-hba-fixed-regulator; + vcc-supply = <&xxx_reg1>; + vcc-supply-1p8; + vccq-supply = <&xxx_reg2>; + vccq2-supply = <&xxx_reg3>; + vcc-max-microamp = 500000; + vccq-max-microamp = 200000; + vccq2-max-microamp = 200000; + + clocks = <&core 0>, <&ref 0>, <&phy 0>, <&iface 0>; + clock-names = "core_clk", "ref_clk", "phy_clk", "iface_clk"; + freq-table-hz = <100000000 200000000>, <0 0>, <0 0>, <0 0>; + resets = <&reset 0 1>; + reset-names = "rst"; + phys = <&ufsphy1>; + phy-names = "ufsphy"; + }; |