diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 111 |
1 files changed, 111 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt new file mode 100644 index 000000000..2e9318151 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -0,0 +1,111 @@ +* USB2 ChipIdea USB controller for ci13xxx + +Required properties: +- compatible: should be one of: + "fsl,imx23-usb" + "fsl,imx27-usb" + "fsl,imx28-usb" + "fsl,imx6q-usb" + "fsl,imx6sl-usb" + "fsl,imx6sx-usb" + "fsl,imx6ul-usb" + "fsl,imx7d-usb" + "lsi,zevio-usb" + "qcom,ci-hdrc" + "chipidea,usb2" + "xlnx,zynq-usb-2.20a" +- reg: base address and length of the registers +- interrupts: interrupt for the USB controller + +Recommended properies: +- phy_type: the type of the phy connected to the core. Should be one + of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this + property the PORTSC register won't be touched. +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +Deprecated properties: +- usb-phy: phandle for the PHY device. Use "phys" instead. +- fsl,usbphy: phandle of usb phy that connects to the port. Use "phys" instead. + +Optional properties: +- clocks: reference to the USB clock +- phys: reference to the USB PHY +- phy-names: should be "usb-phy" +- vbus-supply: reference to the VBUS regulator +- maximum-speed: limit the maximum connection speed to "full-speed". +- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts +- itc-setting: interrupt threshold control register control, the setting + should be aligned with ITC bits at register USBCMD. +- ahb-burst-config: it is vendor dependent, the required value should be + aligned with AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This + property is used to change AHB burst configuration, check the chipidea + spec for meaning of each value. If this property is not existed, it + will use the reset value. +- tx-burst-size-dword: it is vendor dependent, the tx burst size in dword + (4 bytes), This register represents the maximum length of a the burst + in 32-bit words while moving data from system memory to the USB + bus, the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. +- rx-burst-size-dword: it is vendor dependent, the rx burst size in dword + (4 bytes), This register represents the maximum length of a the burst + in 32-bit words while moving data from the USB bus to system memory, + the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. +- extcon: phandles to external connector devices. First phandle should point to + external connector, which provide "USB" cable events, the second should point + to external connector device, which provide "USB-HOST" cable events. If one + of the external connector devices is not required, empty <0> phandle should + be specified. +- phy-clkgate-delay-us: the delay time (us) between putting the PHY into + low power mode and gating the PHY clock. +- non-zero-ttctrl-ttha: after setting this property, the value of register + ttctrl.ttha will be 0x7f; if not, the value will be 0x0, this is the default + value. It needs to be very carefully for setting this property, it is + recommended that consult with your IC engineer before setting this value. + On the most of chipidea platforms, the "usage_tt" flag at RTL is 0, so this + property only affects siTD. + If this property is not set, the max packet size is 1023 bytes, and if + the total of packet size for pervious transactions are more than 256 bytes, + it can't accept any transactions within this frame. The use case is single + transaction, but higher frame rate. + If this property is set, the max packet size is 188 bytes, it can handle + more transactions than above case, it can accept transactions until it + considers the left room size within frame is less than 188 bytes, software + needs to make sure it does not send more than 90% + maximum_periodic_data_per_frame. The use case is multiple transactions, but + less frame rate. +- mux-controls: The mux control for toggling host/device output of this + controller. It's expected that a mux state of 0 indicates device mode and a + mux state of 1 indicates host mode. +- mux-control-names: Shall be "usb_switch" if mux-controls is specified. + +i.mx specific properties +- fsl,usbmisc: phandler of non-core register device, with one + argument that indicate usb controller index +- disable-over-current: disable over current detect +- over-current-active-high: over current signal polarity is high active, + typically over current signal polarity is low active. +- external-vbus-divider: enables off-chip resistor divider for Vbus + +Example: + + usb@f7ed0000 { + compatible = "chipidea,usb2"; + reg = <0xf7ed0000 0x10000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&chip CLKID_USB0>; + phys = <&usb_phy0>; + phy-names = "usb-phy"; + vbus-supply = <®_usb0_vbus>; + itc-setting = <0x4>; /* 4 micro-frames */ + /* Incremental burst of unspecified length */ + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; /* 64 bytes */ + rx-burst-size-dword = <0x10>; + extcon = <0>, <&usb_id>; + phy-clkgate-delay-us = <400>; + mux-controls = <&usb_switch>; + mux-control-names = "usb_switch"; + }; |