diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/fb/pxafb.txt | 142 |
1 files changed, 142 insertions, 0 deletions
diff --git a/Documentation/fb/pxafb.txt b/Documentation/fb/pxafb.txt new file mode 100644 index 000000000..d143a0a74 --- /dev/null +++ b/Documentation/fb/pxafb.txt @@ -0,0 +1,142 @@ +Driver for PXA25x LCD controller +================================ + +The driver supports the following options, either via +options=<OPTIONS> when modular or video=pxafb:<OPTIONS> when built in. + +For example: + modprobe pxafb options=vmem:2M,mode:640x480-8,passive +or on the kernel command line + video=pxafb:vmem:2M,mode:640x480-8,passive + +vmem: VIDEO_MEM_SIZE + Amount of video memory to allocate (can be suffixed with K or M + for kilobytes or megabytes) + +mode:XRESxYRES[-BPP] + XRES == LCCR1_PPL + 1 + YRES == LLCR2_LPP + 1 + The resolution of the display in pixels + BPP == The bit depth. Valid values are 1, 2, 4, 8 and 16. + +pixclock:PIXCLOCK + Pixel clock in picoseconds + +left:LEFT == LCCR1_BLW + 1 +right:RIGHT == LCCR1_ELW + 1 +hsynclen:HSYNC == LCCR1_HSW + 1 +upper:UPPER == LCCR2_BFW +lower:LOWER == LCCR2_EFR +vsynclen:VSYNC == LCCR2_VSW + 1 + Display margins and sync times + +color | mono => LCCR0_CMS + umm... + +active | passive => LCCR0_PAS + Active (TFT) or Passive (STN) display + +single | dual => LCCR0_SDS + Single or dual panel passive display + +4pix | 8pix => LCCR0_DPD + 4 or 8 pixel monochrome single panel data + +hsync:HSYNC +vsync:VSYNC + Horizontal and vertical sync. 0 => active low, 1 => active + high. + +dpc:DPC + Double pixel clock. 1=>true, 0=>false + +outputen:POLARITY + Output Enable Polarity. 0 => active low, 1 => active high + +pixclockpol:POLARITY + pixel clock polarity + 0 => falling edge, 1 => rising edge + + +Overlay Support for PXA27x and later LCD controllers +==================================================== + + PXA27x and later processors support overlay1 and overlay2 on-top of the + base framebuffer (although under-neath the base is also possible). They + support palette and no-palette RGB formats, as well as YUV formats (only + available on overlay2). These overlays have dedicated DMA channels and + behave in a similar way as a framebuffer. + + However, there are some differences between these overlay framebuffers + and normal framebuffers, as listed below: + + 1. overlay can start at a 32-bit word aligned position within the base + framebuffer, which means they have a start (x, y). This information + is encoded into var->nonstd (no, var->xoffset and var->yoffset are + not for such purpose). + + 2. overlay framebuffer is allocated dynamically according to specified + 'struct fb_var_screeninfo', the amount is decided by: + + var->xres_virtual * var->yres_virtual * bpp + + bpp = 16 -- for RGB565 or RGBT555 + = 24 -- for YUV444 packed + = 24 -- for YUV444 planar + = 16 -- for YUV422 planar (1 pixel = 1 Y + 1/2 Cb + 1/2 Cr) + = 12 -- for YUV420 planar (1 pixel = 1 Y + 1/4 Cb + 1/4 Cr) + + NOTE: + + a. overlay does not support panning in x-direction, thus + var->xres_virtual will always be equal to var->xres + + b. line length of overlay(s) must be on a 32-bit word boundary, + for YUV planar modes, it is a requirement for the component + with minimum bits per pixel, e.g. for YUV420, Cr component + for one pixel is actually 2-bits, it means the line length + should be a multiple of 16-pixels + + c. starting horizontal position (XPOS) should start on a 32-bit + word boundary, otherwise the fb_check_var() will just fail. + + d. the rectangle of the overlay should be within the base plane, + otherwise fail + + Applications should follow the sequence below to operate an overlay + framebuffer: + + a. open("/dev/fb[1-2]", ...) + b. ioctl(fd, FBIOGET_VSCREENINFO, ...) + c. modify 'var' with desired parameters: + 1) var->xres and var->yres + 2) larger var->yres_virtual if more memory is required, + usually for double-buffering + 3) var->nonstd for starting (x, y) and color format + 4) var->{red, green, blue, transp} if RGB mode is to be used + d. ioctl(fd, FBIOPUT_VSCREENINFO, ...) + e. ioctl(fd, FBIOGET_FSCREENINFO, ...) + f. mmap + g. ... + + 3. for YUV planar formats, these are actually not supported within the + framebuffer framework, application has to take care of the offsets + and lengths of each component within the framebuffer. + + 4. var->nonstd is used to pass starting (x, y) position and color format, + the detailed bit fields are shown below: + + 31 23 20 10 0 + +-----------------+---+----------+----------+ + | ... unused ... |FOR| XPOS | YPOS | + +-----------------+---+----------+----------+ + + FOR - color format, as defined by OVERLAY_FORMAT_* in pxafb.h + 0 - RGB + 1 - YUV444 PACKED + 2 - YUV444 PLANAR + 3 - YUV422 PLANAR + 4 - YUR420 PLANAR + + XPOS - starting horizontal position + YPOS - starting vertical position |