diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/isdn/README.hysdn | 195 |
1 files changed, 195 insertions, 0 deletions
diff --git a/Documentation/isdn/README.hysdn b/Documentation/isdn/README.hysdn new file mode 100644 index 000000000..eeca11f00 --- /dev/null +++ b/Documentation/isdn/README.hysdn @@ -0,0 +1,195 @@ +$Id: README.hysdn,v 1.3.6.1 2001/02/10 14:41:19 kai Exp $ +The hysdn driver has been written by +Werner Cornelius (werner@isdn4linux.de or werner@titro.de) +for Hypercope GmbH Aachen Germany. Hypercope agreed to publish this driver +under the GNU General Public License. + +The CAPI 2.0-support was added by Ulrich Albrecht (ualbrecht@hypercope.de) +for Hypercope GmbH Aachen, Germany. + + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License as published by + the Free Software Foundation; either version 2 of the License, or + (at your option) any later version. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + +Table of contents +================= + +1. About the driver + +2. Loading/Unloading the driver + +3. Entries in the /proc filesystem + +4. The /proc/net/hysdn/cardconfX file + +5. The /proc/net/hysdn/cardlogX file + +6. Where to get additional info and help + + +1. About the driver + + The drivers/isdn/hysdn subdir contains a driver for HYPERCOPEs active + PCI isdn cards Champ, Ergo and Metro. To enable support for this cards + enable ISDN support in the kernel config and support for HYSDN cards in + the active cards submenu. The driver may only be compiled and used if + support for loadable modules and the process filesystem have been enabled. + + These cards provide two different interfaces to the kernel. Without the + optional CAPI 2.0 support, they register as ethernet card. IP-routing + to a ISDN-destination is performed on the card itself. All necessary + handlers for various protocols like ppp and others as well as config info + and firmware may be fetched from Hypercopes WWW-Site www.hypercope.de. + + With CAPI 2.0 support enabled, the card can also be used as a CAPI 2.0 + compliant devices with either CAPI 2.0 applications + (check isdn4k-utils) or -using the capidrv module- as a regular + isdn4linux device. This is done via the same mechanism as with the + active AVM cards and in fact uses the same module. + + +2. Loading/Unloading the driver + + The module has no command line parameters and auto detects up to 10 cards + in the id-range 0-9. + If a loaded driver shall be unloaded all open files in the /proc/net/hysdn + subdir need to be closed and all ethernet interfaces allocated by this + driver must be shut down. Otherwise the module counter will avoid a module + unload. + + If you are using the CAPI 2.0-interface, make sure to load/modprobe the + kernelcapi-module first. + + If you plan to use the capidrv-link to isdn4linux, make sure to load + capidrv.o after all modules using this driver (i.e. after hysdn and + any avm-specific modules). + +3. Entries in the /proc filesystem + + When the module has been loaded it adds the directory hysdn in the + /proc/net tree. This directory contains exactly 2 file entries for each + card. One is called cardconfX and the other cardlogX, where X is the + card id number from 0 to 9. + The cards are numbered in the order found in the PCI config data. + +4. The /proc/net/hysdn/cardconfX file + + This file may be read to get by everyone to get info about the cards type, + actual state, available features and used resources. + The first 3 entries (id, bus and slot) are PCI info fields, the following + type field gives the information about the cards type: + + 4 -> Ergo card (server card with 2 b-chans) + 5 -> Metro card (server card with 4 or 8 b-chans) + 6 -> Champ card (client card with 2 b-chans) + + The following 3 fields show the hardware assignments for irq, iobase and the + dual ported memory (dp-mem). + The fields b-chans and fax-chans announce the available card resources of + this types for the user. + The state variable indicates the actual drivers state for this card with the + following assignments. + + 0 -> card has not been booted since driver load + 1 -> card booting is actually in progess + 2 -> card is in an error state due to a previous boot failure + 3 -> card is booted and active + + And the last field (device) shows the name of the ethernet device assigned + to this card. Up to the first successful boot this field only shows a - + to tell that no net device has been allocated up to now. Once a net device + has been allocated it remains assigned to this card, even if a card is + rebooted and an boot error occurs. + + Writing to the cardconfX file boots the card or transfers config lines to + the cards firmware. The type of data is automatically detected when the + first data is written. Only root has write access to this file. + The firmware boot files are normally called hyclient.pof for client cards + and hyserver.pof for server cards. + After successfully writing the boot file, complete config files or single + config lines may be copied to this file. + If an error occurs the return value given to the writing process has the + following additional codes (decimal): + + 1000 Another process is currently bootng the card + 1001 Invalid firmware header + 1002 Boards dual-port RAM test failed + 1003 Internal firmware handler error + 1004 Boot image size invalid + 1005 First boot stage (bootstrap loader) failed + 1006 Second boot stage failure + 1007 Timeout waiting for card ready during boot + 1008 Operation only allowed in booted state + 1009 Config line too long + 1010 Invalid channel number + 1011 Timeout sending config data + + Additional info about error reasons may be fetched from the log output. + +5. The /proc/net/hysdn/cardlogX file + + The cardlogX file entry may be opened multiple for reading by everyone to + get the cards and drivers log data. Card messages always start with the + keyword LOG. All other lines are output from the driver. + The driver log data may be redirected to the syslog by selecting the + appropriate bitmask. The cards log messages will always be send to this + interface but never to the syslog. + + A root user may write a decimal or hex (with 0x) value t this file to select + desired output options. As mentioned above the cards log dat is always + written to the cardlog file independent of the following options only used + to check and debug the driver itself: + + For example: + echo "0x34560078" > /proc/net/hysdn/cardlog0 + to output the hex log mask 34560078 for card 0. + + The written value is regarded as an unsigned 32-Bit value, bit ored for + desired output. The following bits are already assigned: + + 0x80000000 All driver log data is alternatively via syslog + 0x00000001 Log memory allocation errors + 0x00000010 Firmware load start and close are logged + 0x00000020 Log firmware record parser + 0x00000040 Log every firmware write actions + 0x00000080 Log all card related boot messages + 0x00000100 Output all config data sent for debugging purposes + 0x00000200 Only non comment config lines are shown wth channel + 0x00000400 Additional conf log output + 0x00001000 Log the asynchronous scheduler actions (config and log) + 0x00100000 Log all open and close actions to /proc/net/hysdn/card files + 0x00200000 Log all actions from /proc file entries + 0x00010000 Log network interface init and deinit + +6. Where to get additional info and help + + If you have any problems concerning the driver or configuration contact + the Hypercope support team (support@hypercope.de) and or the authors + Werner Cornelius (werner@isdn4linux or cornelius@titro.de) or + Ulrich Albrecht (ualbrecht@hypercope.de). + + + + + + + + + + + + + + + |