diff options
Diffstat (limited to 'arch/arm/boot/dts/ste-href-stuib.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/ste-href-stuib.dtsi | 194 |
1 files changed, 194 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/ste-href-stuib.dtsi b/arch/arm/boot/dts/ste-href-stuib.dtsi new file mode 100644 index 000000000..35e944d8b --- /dev/null +++ b/arch/arm/boot/dts/ste-href-stuib.dtsi @@ -0,0 +1,194 @@ +/* + * Copyright 2012 ST-Ericsson AB + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include <dt-bindings/interrupt-controller/irq.h> + +/ { + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&prox_stuib_mode>, <&hall_stuib_mode>; + + button@139 { + /* Proximity sensor */ + gpios = <&gpio6 25 GPIO_ACTIVE_HIGH>; + linux,code = <11>; /* SW_FRONT_PROXIMITY */ + label = "SFH7741 Proximity Sensor"; + }; + button@145 { + /* Hall sensor */ + gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>; + linux,code = <0>; /* SW_LID */ + label = "HED54XXU11 Hall Effect Sensor"; + }; + }; + + soc { + i2c@80004000 { + stmpe1601: stmpe1601@40 { + compatible = "st,stmpe1601"; + reg = <0x40>; + interrupts = <26 IRQ_TYPE_EDGE_FALLING>; + interrupt-parent = <&gpio6>; + interrupt-controller; + vcc-supply = <&db8500_vsmps2_reg>; + vio-supply = <&db8500_vsmps2_reg>; + + wakeup-source; + st,autosleep-timeout = <1024>; + + stmpe_keypad { + compatible = "st,stmpe-keypad"; + + debounce-interval = <64>; + st,scan-count = <8>; + st,no-autorepeat; + + linux,keymap = <0x205006b + 0x4010074 + 0x3050072 + 0x1030004 + 0x502006a + 0x500000a + 0x5008b + 0x706001c + 0x405000b + 0x6070003 + 0x3040067 + 0x303006c + 0x60400e7 + 0x602009e + 0x4020073 + 0x5050002 + 0x4030069 + 0x3020008>; + }; + }; + }; + + /* Sensors mounted on this board variant */ + i2c@80128000 { + lis331dl@1c { + /* Accelerometer */ + compatible = "st,lis331dl-accel"; + st,drdy-int-pin = <1>; + reg = <0x1c>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_stuib_mode>; + interrupt-parent = <&gpio2>; + interrupts = <18 IRQ_TYPE_EDGE_RISING>, + <19 IRQ_TYPE_EDGE_RISING>; + }; + ak8974@f { + /* Magnetometer */ + compatible = "asahi-kasei,ak8974"; + reg = <0x0f>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vddio-supply = <&db8500_vsmps2_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&magneto_stuib_mode>; + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_EDGE_RISING>; + }; + }; + + i2c@80110000 { + bu21013_tp@5c { + compatible = "rohm,bu21013_tp"; + reg = <0x5c>; + avdd-supply = <&ab8500_ldo_aux1_reg>; + + rohm,touch-max-x = <384>; + rohm,touch-max-y = <704>; + rohm,flip-y; + pinctrl-names = "default"; + pinctrl-0 = <&touch_rohm_mode>; + }; + + bu21013_tp@5d { + compatible = "rohm,bu21013_tp"; + reg = <0x5d>; + avdd-supply = <&ab8500_ldo_aux1_reg>; + + rohm,touch-max-x = <384>; + rohm,touch-max-y = <704>; + rohm,flip-y; + pinctrl-names = "default"; + pinctrl-0 = <&touch_rohm_mode>; + }; + }; + + pinctrl { + prox { + prox_stuib_mode: prox_stuib { + stuib_cfg { + pins = "GPIO217_AH12"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + hall { + hall_stuib_mode: stuib_tvk { + stuib_cfg { + pins = "GPIO145_C13"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + accelerometer { + accel_stuib_mode: accel_stuib { + /* Accelerometer interrupt lines 1 & 2 */ + stuib_cfg { + pins = "GPIO82_C1", "GPIO83_D3"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + magnetometer { + magneto_stuib_mode: magneto_stuib { + /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */ + stuib_cfg1 { + pins = "GPIO31_V3"; + ste,config = <&gpio_in_pu>; + }; + stuib_cfg2 { + pins = "GPIO32_V2"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + touch { + touch_rohm_mode: touch_rohm { + /* + * ROHM touch screen uses GPIO 143 for + * RST1, GPIO 146 for RST2 and + * GPIO 67 for interrupts. Pull-up + * the IRQ line and drive both + * reset signals low. + */ + stuib_cfg1 { + pins = "GPIO143_D12", "GPIO146_D13"; + ste,config = <&gpio_out_lo>; + }; + stuib_cfg2 { + pins = "GPIO67_G2"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + }; + }; +}; |