diff options
Diffstat (limited to '')
| -rw-r--r-- | arch/sh/drivers/pci/pci-sh5.c | 219 |
1 files changed, 219 insertions, 0 deletions
diff --git a/arch/sh/drivers/pci/pci-sh5.c b/arch/sh/drivers/pci/pci-sh5.c new file mode 100644 index 000000000..8229114c6 --- /dev/null +++ b/arch/sh/drivers/pci/pci-sh5.c @@ -0,0 +1,219 @@ +/* + * Copyright (C) 2001 David J. Mckay (david.mckay@st.com) + * Copyright (C) 2003, 2004 Paul Mundt + * Copyright (C) 2004 Richard Curnow + * + * May be copied or modified under the terms of the GNU General Public + * License. See linux/COPYING for more information. + * + * Support functions for the SH5 PCI hardware. + */ + +#include <linux/kernel.h> +#include <linux/rwsem.h> +#include <linux/smp.h> +#include <linux/interrupt.h> +#include <linux/init.h> +#include <linux/errno.h> +#include <linux/pci.h> +#include <linux/delay.h> +#include <linux/types.h> +#include <linux/irq.h> +#include <cpu/irq.h> +#include <asm/io.h> +#include "pci-sh5.h" + +unsigned long pcicr_virt; +unsigned long PCI_IO_AREA; + +/* Rounds a number UP to the nearest power of two. Used for + * sizing the PCI window. + */ +static u32 __init r2p2(u32 num) +{ + int i = 31; + u32 tmp = num; + + if (num == 0) + return 0; + + do { + if (tmp & (1 << 31)) + break; + i--; + tmp <<= 1; + } while (i >= 0); + + tmp = 1 << i; + /* If the original number isn't a power of 2, round it up */ + if (tmp != num) + tmp <<= 1; + + return tmp; +} + +static irqreturn_t pcish5_err_irq(int irq, void *dev_id) +{ + struct pt_regs *regs = get_irq_regs(); + unsigned pci_int, pci_air, pci_cir, pci_aint; + + pci_int = SH5PCI_READ(INT); + pci_cir = SH5PCI_READ(CIR); + pci_air = SH5PCI_READ(AIR); + + if (pci_int) { + printk("PCI INTERRUPT (at %08llx)!\n", regs->pc); + printk("PCI INT -> 0x%x\n", pci_int & 0xffff); + printk("PCI AIR -> 0x%x\n", pci_air); + printk("PCI CIR -> 0x%x\n", pci_cir); + SH5PCI_WRITE(INT, ~0); + } + + pci_aint = SH5PCI_READ(AINT); + if (pci_aint) { + printk("PCI ARB INTERRUPT!\n"); + printk("PCI AINT -> 0x%x\n", pci_aint); + printk("PCI AIR -> 0x%x\n", pci_air); + printk("PCI CIR -> 0x%x\n", pci_cir); + SH5PCI_WRITE(AINT, ~0); + } + + return IRQ_HANDLED; +} + +static irqreturn_t pcish5_serr_irq(int irq, void *dev_id) +{ + printk("SERR IRQ\n"); + + return IRQ_NONE; +} + +static struct resource sh5_pci_resources[2]; + +static struct pci_channel sh5pci_controller = { + .pci_ops = &sh5_pci_ops, + .resources = sh5_pci_resources, + .nr_resources = ARRAY_SIZE(sh5_pci_resources), + .mem_offset = 0x00000000, + .io_offset = 0x00000000, +}; + +static int __init sh5pci_init(void) +{ + unsigned long memStart = __pa(memory_start); + unsigned long memSize = __pa(memory_end) - memStart; + u32 lsr0; + u32 uval; + + if (request_irq(IRQ_ERR, pcish5_err_irq, + 0, "PCI Error",NULL) < 0) { + printk(KERN_ERR "PCISH5: Cannot hook PCI_PERR interrupt\n"); + return -EINVAL; + } + + if (request_irq(IRQ_SERR, pcish5_serr_irq, + 0, "PCI SERR interrupt", NULL) < 0) { + printk(KERN_ERR "PCISH5: Cannot hook PCI_SERR interrupt\n"); + return -EINVAL; + } + + pcicr_virt = (unsigned long)ioremap_nocache(SH5PCI_ICR_BASE, 1024); + if (!pcicr_virt) { + panic("Unable to remap PCICR\n"); + } + + PCI_IO_AREA = (unsigned long)ioremap_nocache(SH5PCI_IO_BASE, 0x10000); + if (!PCI_IO_AREA) { + panic("Unable to remap PCIIO\n"); + } + + /* Clear snoop registers */ + SH5PCI_WRITE(CSCR0, 0); + SH5PCI_WRITE(CSCR1, 0); + + /* Switch off interrupts */ + SH5PCI_WRITE(INTM, 0); + SH5PCI_WRITE(AINTM, 0); + SH5PCI_WRITE(PINTM, 0); + + /* Set bus active, take it out of reset */ + uval = SH5PCI_READ(CR); + + /* Set command Register */ + SH5PCI_WRITE(CR, uval | CR_LOCK_MASK | CR_CFINT| CR_FTO | CR_PFE | + CR_PFCS | CR_BMAM); + + uval=SH5PCI_READ(CR); + + /* Allow it to be a master */ + /* NB - WE DISABLE I/O ACCESS to stop overlap */ + /* set WAIT bit to enable stepping, an attempt to improve stability */ + SH5PCI_WRITE_SHORT(CSR_CMD, + PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER | + PCI_COMMAND_WAIT); + + /* + ** Set translation mapping memory in order to convert the address + ** used for the main bus, to the PCI internal address. + */ + SH5PCI_WRITE(MBR,0x40000000); + + /* Always set the max size 512M */ + SH5PCI_WRITE(MBMR, PCISH5_MEM_SIZCONV(512*1024*1024)); + + /* + ** I/O addresses are mapped at internal PCI specific address + ** as is described into the configuration bridge table. + ** These are changed to 0, to allow cards that have legacy + ** io such as vga to function correctly. We set the SH5 IOBAR to + ** 256K, which is a bit big as we can only have 64K of address space + */ + + SH5PCI_WRITE(IOBR,0x0); + + /* Set up a 256K window. Totally pointless waste of address space */ + SH5PCI_WRITE(IOBMR,0); + + /* The SH5 has a HUGE 256K I/O region, which breaks the PCI spec. + * Ideally, we would want to map the I/O region somewhere, but it + * is so big this is not that easy! + */ + SH5PCI_WRITE(CSR_IBAR0,~0); + /* Set memory size value */ + memSize = memory_end - memory_start; + + /* Now we set up the mbars so the PCI bus can see the memory of + * the machine */ + if (memSize < (1024 * 1024)) { + printk(KERN_ERR "PCISH5: Ridiculous memory size of 0x%lx?\n", + memSize); + return -EINVAL; + } + + /* Set LSR 0 */ + lsr0 = (memSize > (512 * 1024 * 1024)) ? 0x1ff00001 : + ((r2p2(memSize) - 0x100000) | 0x1); + SH5PCI_WRITE(LSR0, lsr0); + + /* Set MBAR 0 */ + SH5PCI_WRITE(CSR_MBAR0, memory_start); + SH5PCI_WRITE(LAR0, memory_start); + + SH5PCI_WRITE(CSR_MBAR1,0); + SH5PCI_WRITE(LAR1,0); + SH5PCI_WRITE(LSR1,0); + + /* Enable the PCI interrupts on the device */ + SH5PCI_WRITE(INTM, ~0); + SH5PCI_WRITE(AINTM, ~0); + SH5PCI_WRITE(PINTM, ~0); + + sh5_pci_resources[0].start = PCI_IO_AREA; + sh5_pci_resources[0].end = PCI_IO_AREA + 0x10000; + + sh5_pci_resources[1].start = memStart; + sh5_pci_resources[1].end = memStart + memSize; + + return register_pci_controller(&sh5pci_controller); +} +arch_initcall(sh5pci_init); |