1 files changed, 292 insertions, 0 deletions
diff --git a/drivers/ata/pata_hpt3x3.c b/drivers/ata/pata_hpt3x3.c
new file mode 100644
index 000000000..b2fc02378
--- /dev/null
+++ b/drivers/ata/pata_hpt3x3.c
@@ -0,0 +1,292 @@
+/*
+ *	pata_hpt3x3		-	HPT3x3 driver
+ *	(c) Copyright 2005-2006 Red Hat
+ *
+ *	Was pata_hpt34x but the naming was confusing as it supported the
+ *	343 and 363 so it has been renamed.
+ *
+ *	Based on:
+ *	linux/drivers/ide/pci/hpt34x.c		Version 0.40	Sept 10, 2002
+ *	Copyright (C) 1998-2000	Andre Hedrick <andre@linux-ide.org>
+ *
+ *	May be copied or modified under the terms of the GNU General Public
+ *	License
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME	"pata_hpt3x3"
+#define DRV_VERSION	"0.6.1"
+
+/**
+ *	hpt3x3_set_piomode		-	PIO setup
+ *	@ap: ATA interface
+ *	@adev: device on the interface
+ *
+ *	Set our PIO requirements. This is fairly simple on the HPT3x3 as
+ *	all we have to do is clear the MWDMA and UDMA bits then load the
+ *	mode number.
+ */
+
+static void hpt3x3_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 r1, r2;
+	int dn = 2 * ap->port_no + adev->devno;
+
+	pci_read_config_dword(pdev, 0x44, &r1);
+	pci_read_config_dword(pdev, 0x48, &r2);
+	/* Load the PIO timing number */
+	r1 &= ~(7 << (3 * dn));
+	r1 |= (adev->pio_mode - XFER_PIO_0) << (3 * dn);
+	r2 &= ~(0x11 << dn);	/* Clear MWDMA and UDMA bits */
+
+	pci_write_config_dword(pdev, 0x44, r1);
+	pci_write_config_dword(pdev, 0x48, r2);
+}
+
+#if defined(CONFIG_PATA_HPT3X3_DMA)
+/**
+ *	hpt3x3_set_dmamode		-	DMA timing setup
+ *	@ap: ATA interface
+ *	@adev: Device being configured
+ *
+ *	Set up the channel for MWDMA or UDMA modes. Much the same as with
+ *	PIO, load the mode number and then set MWDMA or UDMA flag.
+ *
+ *	0x44 : bit 0-2 master mode, 3-5 slave mode, etc
+ *	0x48 : bit 4/0 DMA/UDMA bit 5/1 for slave etc
+ */
+
+static void hpt3x3_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+	u32 r1, r2;
+	int dn = 2 * ap->port_no + adev->devno;
+	int mode_num = adev->dma_mode & 0x0F;
+
+	pci_read_config_dword(pdev, 0x44, &r1);
+	pci_read_config_dword(pdev, 0x48, &r2);
+	/* Load the timing number */
+	r1 &= ~(7 << (3 * dn));
+	r1 |= (mode_num << (3 * dn));
+	r2 &= ~(0x11 << dn);	/* Clear MWDMA and UDMA bits */
+
+	if (adev->dma_mode >= XFER_UDMA_0)
+		r2 |= (0x01 << dn);	/* Ultra mode */
+	else
+		r2 |= (0x10 << dn);	/* MWDMA */
+
+	pci_write_config_dword(pdev, 0x44, r1);
+	pci_write_config_dword(pdev, 0x48, r2);
+}
+
+/**
+ *	hpt3x3_freeze		-	DMA workaround
+ *	@ap: port to freeze
+ *
+ *	When freezing an HPT3x3 we must stop any pending DMA before
+ *	writing to the control register or the chip will hang
+ */
+
+static void hpt3x3_freeze(struct ata_port *ap)
+{
+	void __iomem *mmio = ap->ioaddr.bmdma_addr;
+
+	iowrite8(ioread8(mmio + ATA_DMA_CMD) & ~ ATA_DMA_START,
+			mmio + ATA_DMA_CMD);
+	ata_sff_dma_pause(ap);
+	ata_sff_freeze(ap);
+}
+
+/**
+ *	hpt3x3_bmdma_setup	-	DMA workaround
+ *	@qc: Queued command
+ *
+ *	When issuing BMDMA we must clean up the error/active bits in
+ *	software on this device
+ */
+
+static void hpt3x3_bmdma_setup(struct ata_queued_cmd *qc)
+{
+	struct ata_port *ap = qc->ap;
+	u8 r = ioread8(ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+	r |= ATA_DMA_INTR | ATA_DMA_ERR;
+	iowrite8(r, ap->ioaddr.bmdma_addr + ATA_DMA_STATUS);
+	return ata_bmdma_setup(qc);
+}
+
+/**
+ *	hpt3x3_atapi_dma	-	ATAPI DMA check
+ *	@qc: Queued command
+ *
+ *	Just say no - we don't do ATAPI DMA
+ */
+
+static int hpt3x3_atapi_dma(struct ata_queued_cmd *qc)
+{
+	return 1;
+}
+
+#endif /* CONFIG_PATA_HPT3X3_DMA */
+
+static struct scsi_host_template hpt3x3_sht = {
+	ATA_BMDMA_SHT(DRV_NAME),
+};
+
+static struct ata_port_operations hpt3x3_port_ops = {
+	.inherits	= &ata_bmdma_port_ops,
+	.cable_detect	= ata_cable_40wire,
+	.set_piomode	= hpt3x3_set_piomode,
+#if defined(CONFIG_PATA_HPT3X3_DMA)
+	.set_dmamode	= hpt3x3_set_dmamode,
+	.bmdma_setup	= hpt3x3_bmdma_setup,
+	.check_atapi_dma= hpt3x3_atapi_dma,
+	.freeze		= hpt3x3_freeze,
+#endif
+
+};
+
+/**
+ *	hpt3x3_init_chipset	-	chip setup
+ *	@dev: PCI device
+ *
+ *	Perform the setup required at boot and on resume.
+ */
+
+static void hpt3x3_init_chipset(struct pci_dev *dev)
+{
+	u16 cmd;
+	/* Initialize the board */
+	pci_write_config_word(dev, 0x80, 0x00);
+	/* Check if it is a 343 or a 363. 363 has COMMAND_MEMORY set */
+	pci_read_config_word(dev, PCI_COMMAND, &cmd);
+	if (cmd & PCI_COMMAND_MEMORY)
+		pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0xF0);
+	else
+		pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x20);
+}
+
+/**
+ *	hpt3x3_init_one		-	Initialise an HPT343/363
+ *	@pdev: PCI device
+ *	@id: Entry in match table
+ *
+ *	Perform basic initialisation. We set the device up so we access all
+ *	ports via BAR4. This is necessary to work around errata.
+ */
+
+static int hpt3x3_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	static const struct ata_port_info info = {
+		.flags = ATA_FLAG_SLAVE_POSS,
+		.pio_mask = ATA_PIO4,
+#if defined(CONFIG_PATA_HPT3X3_DMA)
+		/* Further debug needed */
+		.mwdma_mask = ATA_MWDMA2,
+		.udma_mask = ATA_UDMA2,
+#endif
+		.port_ops = &hpt3x3_port_ops
+	};
+	/* Register offsets of taskfiles in BAR4 area */
+	static const u8 offset_cmd[2] = { 0x20, 0x28 };
+	static const u8 offset_ctl[2] = { 0x36, 0x3E };
+	const struct ata_port_info *ppi[] = { &info, NULL };
+	struct ata_host *host;
+	int i, rc;
+	void __iomem *base;
+
+	hpt3x3_init_chipset(pdev);
+
+	ata_print_version_once(&pdev->dev, DRV_VERSION);
+
+	host = ata_host_alloc_pinfo(&pdev->dev, ppi, 2);
+	if (!host)
+		return -ENOMEM;
+	/* acquire resources and fill host */
+	rc = pcim_enable_device(pdev);
+	if (rc)
+		return rc;
+
+	/* Everything is relative to BAR4 if we set up this way */
+	rc = pcim_iomap_regions(pdev, 1 << 4, DRV_NAME);
+	if (rc == -EBUSY)
+		pcim_pin_device(pdev);
+	if (rc)
+		return rc;
+	host->iomap = pcim_iomap_table(pdev);
+	rc = dma_set_mask(&pdev->dev, ATA_DMA_MASK);
+	if (rc)
+		return rc;
+	rc = dma_set_coherent_mask(&pdev->dev, ATA_DMA_MASK);
+	if (rc)
+		return rc;
+
+	base = host->iomap[4];	/* Bus mastering base */
+
+	for (i = 0; i < host->n_ports; i++) {
+		struct ata_port *ap = host->ports[i];
+		struct ata_ioports *ioaddr = &ap->ioaddr;
+
+		ioaddr->cmd_addr = base + offset_cmd[i];
+		ioaddr->altstatus_addr =
+		ioaddr->ctl_addr = base + offset_ctl[i];
+		ioaddr->scr_addr = NULL;
+		ata_sff_std_ports(ioaddr);
+		ioaddr->bmdma_addr = base + 8 * i;
+
+		ata_port_pbar_desc(ap, 4, -1, "ioport");
+		ata_port_pbar_desc(ap, 4, offset_cmd[i], "cmd");
+	}
+	pci_set_master(pdev);
+	return ata_host_activate(host, pdev->irq, ata_bmdma_interrupt,
+				 IRQF_SHARED, &hpt3x3_sht);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int hpt3x3_reinit_one(struct pci_dev *dev)
+{
+	struct ata_host *host = pci_get_drvdata(dev);
+	int rc;
+
+	rc = ata_pci_device_do_resume(dev);
+	if (rc)
+		return rc;
+
+	hpt3x3_init_chipset(dev);
+
+	ata_host_resume(host);
+	return 0;
+}
+#endif
+
+static const struct pci_device_id hpt3x3[] = {
+	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT343), },
+
+	{ },
+};
+
+static struct pci_driver hpt3x3_pci_driver = {
+	.name 		= DRV_NAME,
+	.id_table	= hpt3x3,
+	.probe 		= hpt3x3_init_one,
+	.remove		= ata_pci_remove_one,
+#ifdef CONFIG_PM_SLEEP
+	.suspend	= ata_pci_device_suspend,
+	.resume		= hpt3x3_reinit_one,
+#endif
+};
+
+module_pci_driver(hpt3x3_pci_driver);
+
+MODULE_AUTHOR("Alan Cox");
+MODULE_DESCRIPTION("low-level driver for the Highpoint HPT343/363");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, hpt3x3);
+MODULE_VERSION(DRV_VERSION);