diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/ata/pata_it8213.c | 298 |
1 files changed, 298 insertions, 0 deletions
diff --git a/drivers/ata/pata_it8213.c b/drivers/ata/pata_it8213.c new file mode 100644 index 000000000..4f97d1e52 --- /dev/null +++ b/drivers/ata/pata_it8213.c @@ -0,0 +1,298 @@ +/* + * pata_it8213.c - iTE Tech. Inc. IT8213 PATA driver + * + * The IT8213 is a very Intel ICH like device for timing purposes, having + * a similar register layout and the same split clock arrangement. Cable + * detection is different, and it does not have slave channels or all the + * clutter of later ICH/SATA setups. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/device.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/ata.h> + +#define DRV_NAME "pata_it8213" +#define DRV_VERSION "0.0.3" + +/** + * it8213_pre_reset - probe begin + * @link: link + * @deadline: deadline jiffies for the operation + * + * Filter out ports by the enable bits before doing the normal reset + * and probe. + */ + +static int it8213_pre_reset(struct ata_link *link, unsigned long deadline) +{ + static const struct pci_bits it8213_enable_bits[] = { + { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ + }; + struct ata_port *ap = link->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + if (!pci_test_config_bits(pdev, &it8213_enable_bits[ap->port_no])) + return -ENOENT; + + return ata_sff_prereset(link, deadline); +} + +/** + * it8213_cable_detect - check for 40/80 pin + * @ap: Port + * + * Perform cable detection for the 8213 ATA interface. This is + * different to the PIIX arrangement + */ + +static int it8213_cable_detect(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 tmp; + pci_read_config_byte(pdev, 0x42, &tmp); + if (tmp & 2) /* The initial docs are incorrect */ + return ATA_CBL_PATA40; + return ATA_CBL_PATA80; +} + +/** + * it8213_set_piomode - Initialize host controller PATA PIO timings + * @ap: Port whose timings we are configuring + * @adev: Device whose timings we are configuring + * + * Set PIO mode for device, in host controller PCI config space. + * + * LOCKING: + * None (inherited from caller). + */ + +static void it8213_set_piomode (struct ata_port *ap, struct ata_device *adev) +{ + unsigned int pio = adev->pio_mode - XFER_PIO_0; + struct pci_dev *dev = to_pci_dev(ap->host->dev); + unsigned int master_port = ap->port_no ? 0x42 : 0x40; + u16 master_data; + int control = 0; + + /* + * See Intel Document 298600-004 for the timing programing rules + * for PIIX/ICH. The 8213 is a clone so very similar + */ + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + if (pio > 1) + control |= 1; /* TIME */ + if (ata_pio_need_iordy(adev)) /* PIO 3/4 require IORDY */ + control |= 2; /* IE */ + /* Bit 2 is set for ATAPI on the IT8213 - reverse of ICH/PIIX */ + if (adev->class != ATA_DEV_ATA) + control |= 4; /* PPE */ + + pci_read_config_word(dev, master_port, &master_data); + + /* Set PPE, IE, and TIME as appropriate */ + if (adev->devno == 0) { + master_data &= 0xCCF0; + master_data |= control; + master_data |= (timings[pio][0] << 12) | + (timings[pio][1] << 8); + } else { + u8 slave_data; + + master_data &= 0xFF0F; + master_data |= (control << 4); + + /* Slave timing in separate register */ + pci_read_config_byte(dev, 0x44, &slave_data); + slave_data &= 0xF0; + slave_data |= (timings[pio][0] << 2) | timings[pio][1]; + pci_write_config_byte(dev, 0x44, slave_data); + } + + master_data |= 0x4000; /* Ensure SITRE is set */ + pci_write_config_word(dev, master_port, master_data); +} + +/** + * it8213_set_dmamode - Initialize host controller PATA DMA timings + * @ap: Port whose timings we are configuring + * @adev: Device to program + * + * Set UDMA/MWDMA mode for device, in host controller PCI config space. + * This device is basically an ICH alike. + * + * LOCKING: + * None (inherited from caller). + */ + +static void it8213_set_dmamode (struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *dev = to_pci_dev(ap->host->dev); + u16 master_data; + u8 speed = adev->dma_mode; + int devid = adev->devno; + u8 udma_enable; + + static const /* ISP RTC */ + u8 timings[][2] = { { 0, 0 }, + { 0, 0 }, + { 1, 0 }, + { 2, 1 }, + { 2, 3 }, }; + + pci_read_config_word(dev, 0x40, &master_data); + pci_read_config_byte(dev, 0x48, &udma_enable); + + if (speed >= XFER_UDMA_0) { + unsigned int udma = adev->dma_mode - XFER_UDMA_0; + u16 udma_timing; + u16 ideconf; + int u_clock, u_speed; + + /* Clocks follow the PIIX style */ + u_speed = min(2 - (udma & 1), udma); + if (udma > 4) + u_clock = 0x1000; /* 100Mhz */ + else if (udma > 2) + u_clock = 1; /* 66Mhz */ + else + u_clock = 0; /* 33Mhz */ + + udma_enable |= (1 << devid); + + /* Load the UDMA cycle time */ + pci_read_config_word(dev, 0x4A, &udma_timing); + udma_timing &= ~(3 << (4 * devid)); + udma_timing |= u_speed << (4 * devid); + pci_write_config_word(dev, 0x4A, udma_timing); + + /* Load the clock selection */ + pci_read_config_word(dev, 0x54, &ideconf); + ideconf &= ~(0x1001 << devid); + ideconf |= u_clock << devid; + pci_write_config_word(dev, 0x54, ideconf); + } else { + /* + * MWDMA is driven by the PIO timings. We must also enable + * IORDY unconditionally along with TIME1. PPE has already + * been set when the PIO timing was set. + */ + unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; + unsigned int control; + u8 slave_data; + static const unsigned int needed_pio[3] = { + XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 + }; + int pio = needed_pio[mwdma] - XFER_PIO_0; + + control = 3; /* IORDY|TIME1 */ + + /* If the drive MWDMA is faster than it can do PIO then + we must force PIO into PIO0 */ + + if (adev->pio_mode < needed_pio[mwdma]) + /* Enable DMA timing only */ + control |= 8; /* PIO cycles in PIO0 */ + + if (devid) { /* Slave */ + master_data &= 0xFF4F; /* Mask out IORDY|TIME1|DMAONLY */ + master_data |= control << 4; + pci_read_config_byte(dev, 0x44, &slave_data); + slave_data &= 0xF0; + /* Load the matching timing */ + slave_data |= ((timings[pio][0] << 2) | timings[pio][1]) << (ap->port_no ? 4 : 0); + pci_write_config_byte(dev, 0x44, slave_data); + } else { /* Master */ + master_data &= 0xCCF4; /* Mask out IORDY|TIME1|DMAONLY + and master timing bits */ + master_data |= control; + master_data |= + (timings[pio][0] << 12) | + (timings[pio][1] << 8); + } + udma_enable &= ~(1 << devid); + pci_write_config_word(dev, 0x40, master_data); + } + pci_write_config_byte(dev, 0x48, udma_enable); +} + +static struct scsi_host_template it8213_sht = { + ATA_BMDMA_SHT(DRV_NAME), +}; + + +static struct ata_port_operations it8213_ops = { + .inherits = &ata_bmdma_port_ops, + .cable_detect = it8213_cable_detect, + .set_piomode = it8213_set_piomode, + .set_dmamode = it8213_set_dmamode, + .prereset = it8213_pre_reset, +}; + + +/** + * it8213_init_one - Register 8213 ATA PCI device with kernel services + * @pdev: PCI device to register + * @ent: Entry in it8213_pci_tbl matching with @pdev + * + * Called from kernel PCI layer. + * + * LOCKING: + * Inherited from PCI layer (may sleep). + * + * RETURNS: + * Zero on success, or -ERRNO value. + */ + +static int it8213_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static const struct ata_port_info info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA12_ONLY, + .udma_mask = ATA_UDMA6, + .port_ops = &it8213_ops, + }; + /* Current IT8213 stuff is single port */ + const struct ata_port_info *ppi[] = { &info, &ata_dummy_port_info }; + + ata_print_version_once(&pdev->dev, DRV_VERSION); + + return ata_pci_bmdma_init_one(pdev, ppi, &it8213_sht, NULL, 0); +} + +static const struct pci_device_id it8213_pci_tbl[] = { + { PCI_VDEVICE(ITE, PCI_DEVICE_ID_ITE_8213), }, + + { } /* terminate list */ +}; + +static struct pci_driver it8213_pci_driver = { + .name = DRV_NAME, + .id_table = it8213_pci_tbl, + .probe = it8213_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif +}; + +module_pci_driver(it8213_pci_driver); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("SCSI low-level driver for the ITE 8213"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, it8213_pci_tbl); +MODULE_VERSION(DRV_VERSION); |