diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/ata/pata_sc1200.c | 269 |
1 files changed, 269 insertions, 0 deletions
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c new file mode 100644 index 000000000..c71de5d68 --- /dev/null +++ b/drivers/ata/pata_sc1200.c @@ -0,0 +1,269 @@ +/* + * New ATA layer SC1200 driver Alan Cox <alan@lxorguk.ukuu.org.uk> + * + * TODO: Mode selection filtering + * TODO: Needs custom DMA cleanup code + * + * Based very heavily on + * + * linux/drivers/ide/pci/sc1200.c Version 0.91 28-Jan-2003 + * + * Copyright (C) 2000-2002 Mark Lord <mlord@pobox.com> + * May be copied or modified under the terms of the GNU General Public License + * + * Development of this chipset driver was funded + * by the nice folks at National Semiconductor. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> + +#define DRV_NAME "pata_sc1200" +#define DRV_VERSION "0.2.6" + +#define SC1200_REV_A 0x00 +#define SC1200_REV_B1 0x01 +#define SC1200_REV_B3 0x02 +#define SC1200_REV_C1 0x03 +#define SC1200_REV_D1 0x04 + +/** + * sc1200_clock - PCI clock + * + * Return the PCI bus clocking for the SC1200 chipset configuration + * in use. We return 0 for 33MHz 1 for 48MHz and 2 for 66Mhz + */ + +static int sc1200_clock(void) +{ + /* Magic registers that give us the chipset data */ + u8 chip_id = inb(0x903C); + u8 silicon_rev = inb(0x903D); + u16 pci_clock; + + if (chip_id == 0x04 && silicon_rev < SC1200_REV_B1) + return 0; /* 33 MHz mode */ + + /* Clock generator configuration 0x901E its 8/9 are the PCI clocking + 0/3 is 33Mhz 1 is 48 2 is 66 */ + + pci_clock = inw(0x901E); + pci_clock >>= 8; + pci_clock &= 0x03; + if (pci_clock == 3) + pci_clock = 0; + return pci_clock; +} + +/** + * sc1200_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Set our PIO requirements. This is fairly simple on the SC1200 + */ + +static void sc1200_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + static const u32 pio_timings[4][5] = { + /* format0, 33Mhz */ + { 0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010 }, + /* format1, 33Mhz */ + { 0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010 }, + /* format1, 48Mhz */ + { 0xfaa3f4f3, 0xc23232b2, 0x513101c1, 0x31213121, 0x10211021 }, + /* format1, 66Mhz */ + { 0xfff4fff4, 0xf35353d3, 0x814102f1, 0x42314231, 0x11311131 } + }; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 format; + unsigned int reg = 0x40 + 0x10 * ap->port_no; + int mode = adev->pio_mode - XFER_PIO_0; + + pci_read_config_dword(pdev, reg + 4, &format); + format >>= 31; + format += sc1200_clock(); + pci_write_config_dword(pdev, reg + 8 * adev->devno, + pio_timings[format][mode]); +} + +/** + * sc1200_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * We cannot mix MWDMA and UDMA without reloading timings each switch + * master to slave. + */ + +static void sc1200_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + static const u32 udma_timing[3][3] = { + { 0x00921250, 0x00911140, 0x00911030 }, + { 0x00932470, 0x00922260, 0x00922140 }, + { 0x009436A1, 0x00933481, 0x00923261 } + }; + + static const u32 mwdma_timing[3][3] = { + { 0x00077771, 0x00012121, 0x00002020 }, + { 0x000BBBB2, 0x00024241, 0x00013131 }, + { 0x000FFFF3, 0x00035352, 0x00015151 } + }; + + int clock = sc1200_clock(); + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + unsigned int reg = 0x40 + 0x10 * ap->port_no; + int mode = adev->dma_mode; + u32 format; + + if (mode >= XFER_UDMA_0) + format = udma_timing[clock][mode - XFER_UDMA_0]; + else + format = mwdma_timing[clock][mode - XFER_MW_DMA_0]; + + if (adev->devno == 0) { + u32 timings; + + pci_read_config_dword(pdev, reg + 4, &timings); + timings &= 0x80000000UL; + timings |= format; + pci_write_config_dword(pdev, reg + 4, timings); + } else + pci_write_config_dword(pdev, reg + 12, format); +} + +/** + * sc1200_qc_issue - command issue + * @qc: command pending + * + * Called when the libata layer is about to issue a command. We wrap + * this interface so that we can load the correct ATA timings if + * necessary. Specifically we have a problem that there is only + * one MWDMA/UDMA bit. + */ + +static unsigned int sc1200_qc_issue(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct ata_device *adev = qc->dev; + struct ata_device *prev = ap->private_data; + + /* See if the DMA settings could be wrong */ + if (ata_dma_enabled(adev) && adev != prev && prev != NULL) { + /* Maybe, but do the channels match MWDMA/UDMA ? */ + if ((ata_using_udma(adev) && !ata_using_udma(prev)) || + (ata_using_udma(prev) && !ata_using_udma(adev))) + /* Switch the mode bits */ + sc1200_set_dmamode(ap, adev); + } + + return ata_bmdma_qc_issue(qc); +} + +/** + * sc1200_qc_defer - implement serialization + * @qc: command + * + * Serialize command issue on this controller. + */ + +static int sc1200_qc_defer(struct ata_queued_cmd *qc) +{ + struct ata_host *host = qc->ap->host; + struct ata_port *alt = host->ports[1 ^ qc->ap->port_no]; + int rc; + + /* First apply the usual rules */ + rc = ata_std_qc_defer(qc); + if (rc != 0) + return rc; + + /* Now apply serialization rules. Only allow a command if the + other channel state machine is idle */ + if (alt && alt->qc_active) + return ATA_DEFER_PORT; + return 0; +} + +static struct scsi_host_template sc1200_sht = { + ATA_BMDMA_SHT(DRV_NAME), + .sg_tablesize = LIBATA_DUMB_MAX_PRD, +}; + +static struct ata_port_operations sc1200_port_ops = { + .inherits = &ata_bmdma_port_ops, + .qc_prep = ata_bmdma_dumb_qc_prep, + .qc_issue = sc1200_qc_issue, + .qc_defer = sc1200_qc_defer, + .cable_detect = ata_cable_40wire, + .set_piomode = sc1200_set_piomode, + .set_dmamode = sc1200_set_dmamode, +}; + +/** + * sc1200_init_one - Initialise an SC1200 + * @dev: PCI device + * @id: Entry in match table + * + * Just throw the needed data at the libata helper and it does all + * our work. + */ + +static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + static const struct ata_port_info info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA2, + .port_ops = &sc1200_port_ops + }; + const struct ata_port_info *ppi[] = { &info, NULL }; + + return ata_pci_bmdma_init_one(dev, ppi, &sc1200_sht, NULL, 0); +} + +static const struct pci_device_id sc1200[] = { + { PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_SCx200_IDE), }, + + { }, +}; + +static struct pci_driver sc1200_pci_driver = { + .name = DRV_NAME, + .id_table = sc1200, + .probe = sc1200_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = ata_pci_device_resume, +#endif +}; + +module_pci_driver(sc1200_pci_driver); + +MODULE_AUTHOR("Alan Cox, Mark Lord"); +MODULE_DESCRIPTION("low-level driver for the NS/AMD SC1200"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, sc1200); +MODULE_VERSION(DRV_VERSION); |