diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/clk/bcm/clk-iproc.h | 224 |
1 files changed, 224 insertions, 0 deletions
diff --git a/drivers/clk/bcm/clk-iproc.h b/drivers/clk/bcm/clk-iproc.h new file mode 100644 index 000000000..a48ddd3e0 --- /dev/null +++ b/drivers/clk/bcm/clk-iproc.h @@ -0,0 +1,224 @@ +/* + * Copyright (C) 2014 Broadcom Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#ifndef _CLK_IPROC_H +#define _CLK_IPROC_H + +#include <linux/kernel.h> +#include <linux/list.h> +#include <linux/spinlock.h> +#include <linux/slab.h> +#include <linux/device.h> +#include <linux/of.h> +#include <linux/clk-provider.h> + +#define IPROC_CLK_NAME_LEN 25 +#define IPROC_CLK_INVALID_OFFSET 0xffffffff +#define bit_mask(width) ((1 << (width)) - 1) + +/* clocks that should not be disabled at runtime */ +#define IPROC_CLK_AON BIT(0) + +/* PLL that requires gating through ASIU */ +#define IPROC_CLK_PLL_ASIU BIT(1) + +/* PLL that has fractional part of the NDIV */ +#define IPROC_CLK_PLL_HAS_NDIV_FRAC BIT(2) + +/* + * Some of the iProc PLL/clocks may have an ASIC bug that requires read back + * of the same register following the write to flush the write transaction into + * the intended register + */ +#define IPROC_CLK_NEEDS_READ_BACK BIT(3) + +/* + * Some PLLs require the PLL SW override bit to be set before changes can be + * applied to the PLL + */ +#define IPROC_CLK_PLL_NEEDS_SW_CFG BIT(4) + +/* + * Some PLLs use a different way to control clock power, via the PWRDWN bit in + * the PLL control register + */ +#define IPROC_CLK_EMBED_PWRCTRL BIT(5) + +/* + * Some PLLs have separate registers for Status and Control. Identify this to + * let the driver know if additional registers need to be used + */ +#define IPROC_CLK_PLL_SPLIT_STAT_CTRL BIT(6) + +/* + * Some PLLs have an additional divide by 2 in master clock calculation; + * MCLK = VCO_freq / (Mdiv * 2). Identify this to let the driver know + * of modified calculations + */ +#define IPROC_CLK_MCLK_DIV_BY_2 BIT(7) + +/* + * Some PLLs provide a look up table for the leaf clock frequencies and + * auto calculates VCO frequency parameters based on the provided leaf + * clock frequencies. They have a user mode that allows the divider + * controls to be determined by the user + */ +#define IPROC_CLK_PLL_USER_MODE_ON BIT(8) + +/* + * Some PLLs have an active low reset + */ +#define IPROC_CLK_PLL_RESET_ACTIVE_LOW BIT(9) + +/* + * Calculate the PLL parameters are runtime, instead of using table + */ +#define IPROC_CLK_PLL_CALC_PARAM BIT(10) + +/* + * Parameters for VCO frequency configuration + * + * VCO frequency = + * ((ndiv_int + ndiv_frac / 2^20) * (ref freqeuncy / pdiv) + */ +struct iproc_pll_vco_param { + unsigned long rate; + unsigned int ndiv_int; + unsigned int ndiv_frac; + unsigned int pdiv; +}; + +struct iproc_clk_reg_op { + unsigned int offset; + unsigned int shift; + unsigned int width; +}; + +/* + * Clock gating control at the top ASIU level + */ +struct iproc_asiu_gate { + unsigned int offset; + unsigned int en_shift; +}; + +/* + * Control of powering on/off of a PLL + * + * Before powering off a PLL, input isolation (ISO) needs to be enabled + */ +struct iproc_pll_aon_pwr_ctrl { + unsigned int offset; + unsigned int pwr_width; + unsigned int pwr_shift; + unsigned int iso_shift; +}; + +/* + * Control of the PLL reset + */ +struct iproc_pll_reset_ctrl { + unsigned int offset; + unsigned int reset_shift; + unsigned int p_reset_shift; +}; + +/* + * Control of the Ki, Kp, and Ka parameters + */ +struct iproc_pll_dig_filter_ctrl { + unsigned int offset; + unsigned int ki_shift; + unsigned int ki_width; + unsigned int kp_shift; + unsigned int kp_width; + unsigned int ka_shift; + unsigned int ka_width; +}; + +/* + * To enable SW control of the PLL + */ +struct iproc_pll_sw_ctrl { + unsigned int offset; + unsigned int shift; +}; + +struct iproc_pll_vco_ctrl { + unsigned int u_offset; + unsigned int l_offset; +}; + +/* + * Main PLL control parameters + */ +struct iproc_pll_ctrl { + unsigned long flags; + struct iproc_pll_aon_pwr_ctrl aon; + struct iproc_asiu_gate asiu; + struct iproc_pll_reset_ctrl reset; + struct iproc_pll_dig_filter_ctrl dig_filter; + struct iproc_pll_sw_ctrl sw_ctrl; + struct iproc_clk_reg_op ndiv_int; + struct iproc_clk_reg_op ndiv_frac; + struct iproc_clk_reg_op pdiv; + struct iproc_pll_vco_ctrl vco_ctrl; + struct iproc_clk_reg_op status; + struct iproc_clk_reg_op macro_mode; +}; + +/* + * Controls enabling/disabling a PLL derived clock + */ +struct iproc_clk_enable_ctrl { + unsigned int offset; + unsigned int enable_shift; + unsigned int hold_shift; + unsigned int bypass_shift; +}; + +/* + * Main clock control parameters for clocks derived from the PLLs + */ +struct iproc_clk_ctrl { + unsigned int channel; + unsigned long flags; + struct iproc_clk_enable_ctrl enable; + struct iproc_clk_reg_op mdiv; +}; + +/* + * Divisor of the ASIU clocks + */ +struct iproc_asiu_div { + unsigned int offset; + unsigned int en_shift; + unsigned int high_shift; + unsigned int high_width; + unsigned int low_shift; + unsigned int low_width; +}; + +void iproc_armpll_setup(struct device_node *node); +void iproc_pll_clk_setup(struct device_node *node, + const struct iproc_pll_ctrl *pll_ctrl, + const struct iproc_pll_vco_param *vco, + unsigned int num_vco_entries, + const struct iproc_clk_ctrl *clk_ctrl, + unsigned int num_clks); +void iproc_asiu_setup(struct device_node *node, + const struct iproc_asiu_div *div, + const struct iproc_asiu_gate *gate, + unsigned int num_clks); + +#endif /* _CLK_IPROC_H */ |