diff options
Diffstat (limited to 'drivers/input/touchscreen/bu21013_ts.c')
| -rw-r--r-- | drivers/input/touchscreen/bu21013_ts.c | 730 |
1 files changed, 730 insertions, 0 deletions
diff --git a/drivers/input/touchscreen/bu21013_ts.c b/drivers/input/touchscreen/bu21013_ts.c new file mode 100644 index 000000000..4fa5da8d5 --- /dev/null +++ b/drivers/input/touchscreen/bu21013_ts.c @@ -0,0 +1,730 @@ +/* + * Copyright (C) ST-Ericsson SA 2010 + * Author: Naveen Kumar G <naveen.gaddipati@stericsson.com> for ST-Ericsson + * License terms:GNU General Public License (GPL) version 2 + */ + +#include <linux/kernel.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/i2c.h> +#include <linux/workqueue.h> +#include <linux/input.h> +#include <linux/input/bu21013.h> +#include <linux/slab.h> +#include <linux/regulator/consumer.h> +#include <linux/module.h> +#include <linux/gpio.h> +#include <linux/of.h> +#include <linux/of_gpio.h> + +#define PEN_DOWN_INTR 0 +#define MAX_FINGERS 2 +#define RESET_DELAY 30 +#define PENUP_TIMEOUT (10) +#define DELTA_MIN 16 +#define MASK_BITS 0x03 +#define SHIFT_8 8 +#define SHIFT_2 2 +#define LENGTH_OF_BUFFER 11 +#define I2C_RETRY_COUNT 5 + +#define BU21013_SENSORS_BTN_0_7_REG 0x70 +#define BU21013_SENSORS_BTN_8_15_REG 0x71 +#define BU21013_SENSORS_BTN_16_23_REG 0x72 +#define BU21013_X1_POS_MSB_REG 0x73 +#define BU21013_X1_POS_LSB_REG 0x74 +#define BU21013_Y1_POS_MSB_REG 0x75 +#define BU21013_Y1_POS_LSB_REG 0x76 +#define BU21013_X2_POS_MSB_REG 0x77 +#define BU21013_X2_POS_LSB_REG 0x78 +#define BU21013_Y2_POS_MSB_REG 0x79 +#define BU21013_Y2_POS_LSB_REG 0x7A +#define BU21013_INT_CLR_REG 0xE8 +#define BU21013_INT_MODE_REG 0xE9 +#define BU21013_GAIN_REG 0xEA +#define BU21013_OFFSET_MODE_REG 0xEB +#define BU21013_XY_EDGE_REG 0xEC +#define BU21013_RESET_REG 0xED +#define BU21013_CALIB_REG 0xEE +#define BU21013_DONE_REG 0xEF +#define BU21013_SENSOR_0_7_REG 0xF0 +#define BU21013_SENSOR_8_15_REG 0xF1 +#define BU21013_SENSOR_16_23_REG 0xF2 +#define BU21013_POS_MODE1_REG 0xF3 +#define BU21013_POS_MODE2_REG 0xF4 +#define BU21013_CLK_MODE_REG 0xF5 +#define BU21013_IDLE_REG 0xFA +#define BU21013_FILTER_REG 0xFB +#define BU21013_TH_ON_REG 0xFC +#define BU21013_TH_OFF_REG 0xFD + + +#define BU21013_RESET_ENABLE 0x01 + +#define BU21013_SENSORS_EN_0_7 0x3F +#define BU21013_SENSORS_EN_8_15 0xFC +#define BU21013_SENSORS_EN_16_23 0x1F + +#define BU21013_POS_MODE1_0 0x02 +#define BU21013_POS_MODE1_1 0x04 +#define BU21013_POS_MODE1_2 0x08 + +#define BU21013_POS_MODE2_ZERO 0x01 +#define BU21013_POS_MODE2_AVG1 0x02 +#define BU21013_POS_MODE2_AVG2 0x04 +#define BU21013_POS_MODE2_EN_XY 0x08 +#define BU21013_POS_MODE2_EN_RAW 0x10 +#define BU21013_POS_MODE2_MULTI 0x80 + +#define BU21013_CLK_MODE_DIV 0x01 +#define BU21013_CLK_MODE_EXT 0x02 +#define BU21013_CLK_MODE_CALIB 0x80 + +#define BU21013_IDLET_0 0x01 +#define BU21013_IDLET_1 0x02 +#define BU21013_IDLET_2 0x04 +#define BU21013_IDLET_3 0x08 +#define BU21013_IDLE_INTERMIT_EN 0x10 + +#define BU21013_DELTA_0_6 0x7F +#define BU21013_FILTER_EN 0x80 + +#define BU21013_INT_MODE_LEVEL 0x00 +#define BU21013_INT_MODE_EDGE 0x01 + +#define BU21013_GAIN_0 0x01 +#define BU21013_GAIN_1 0x02 +#define BU21013_GAIN_2 0x04 + +#define BU21013_OFFSET_MODE_DEFAULT 0x00 +#define BU21013_OFFSET_MODE_MOVE 0x01 +#define BU21013_OFFSET_MODE_DISABLE 0x02 + +#define BU21013_TH_ON_0 0x01 +#define BU21013_TH_ON_1 0x02 +#define BU21013_TH_ON_2 0x04 +#define BU21013_TH_ON_3 0x08 +#define BU21013_TH_ON_4 0x10 +#define BU21013_TH_ON_5 0x20 +#define BU21013_TH_ON_6 0x40 +#define BU21013_TH_ON_7 0x80 +#define BU21013_TH_ON_MAX 0xFF + +#define BU21013_TH_OFF_0 0x01 +#define BU21013_TH_OFF_1 0x02 +#define BU21013_TH_OFF_2 0x04 +#define BU21013_TH_OFF_3 0x08 +#define BU21013_TH_OFF_4 0x10 +#define BU21013_TH_OFF_5 0x20 +#define BU21013_TH_OFF_6 0x40 +#define BU21013_TH_OFF_7 0x80 +#define BU21013_TH_OFF_MAX 0xFF + +#define BU21013_X_EDGE_0 0x01 +#define BU21013_X_EDGE_1 0x02 +#define BU21013_X_EDGE_2 0x04 +#define BU21013_X_EDGE_3 0x08 +#define BU21013_Y_EDGE_0 0x10 +#define BU21013_Y_EDGE_1 0x20 +#define BU21013_Y_EDGE_2 0x40 +#define BU21013_Y_EDGE_3 0x80 + +#define BU21013_DONE 0x01 +#define BU21013_NUMBER_OF_X_SENSORS (6) +#define BU21013_NUMBER_OF_Y_SENSORS (11) + +#define DRIVER_TP "bu21013_tp" + +/** + * struct bu21013_ts_data - touch panel data structure + * @client: pointer to the i2c client + * @wait: variable to wait_queue_head_t structure + * @touch_stopped: touch stop flag + * @chip: pointer to the touch panel controller + * @in_dev: pointer to the input device structure + * @intr_pin: interrupt pin value + * @regulator: pointer to the Regulator used for touch screen + * + * Touch panel device data structure + */ +struct bu21013_ts_data { + struct i2c_client *client; + wait_queue_head_t wait; + const struct bu21013_platform_device *chip; + struct input_dev *in_dev; + struct regulator *regulator; + unsigned int irq; + unsigned int intr_pin; + bool touch_stopped; +}; + +/** + * bu21013_read_block_data(): read the touch co-ordinates + * @data: bu21013_ts_data structure pointer + * @buf: byte pointer + * + * Read the touch co-ordinates using i2c read block into buffer + * and returns integer. + */ +static int bu21013_read_block_data(struct bu21013_ts_data *data, u8 *buf) +{ + int ret, i; + + for (i = 0; i < I2C_RETRY_COUNT; i++) { + ret = i2c_smbus_read_i2c_block_data + (data->client, BU21013_SENSORS_BTN_0_7_REG, + LENGTH_OF_BUFFER, buf); + if (ret == LENGTH_OF_BUFFER) + return 0; + } + return -EINVAL; +} + +/** + * bu21013_do_touch_report(): Get the touch co-ordinates + * @data: bu21013_ts_data structure pointer + * + * Get the touch co-ordinates from touch sensor registers and writes + * into device structure and returns integer. + */ +static int bu21013_do_touch_report(struct bu21013_ts_data *data) +{ + u8 buf[LENGTH_OF_BUFFER]; + unsigned int pos_x[2], pos_y[2]; + bool has_x_sensors, has_y_sensors; + int finger_down_count = 0; + int i; + + if (data == NULL) + return -EINVAL; + + if (bu21013_read_block_data(data, buf) < 0) + return -EINVAL; + + has_x_sensors = hweight32(buf[0] & BU21013_SENSORS_EN_0_7); + has_y_sensors = hweight32(((buf[1] & BU21013_SENSORS_EN_8_15) | + ((buf[2] & BU21013_SENSORS_EN_16_23) << SHIFT_8)) >> SHIFT_2); + if (!has_x_sensors || !has_y_sensors) + return 0; + + for (i = 0; i < MAX_FINGERS; i++) { + const u8 *p = &buf[4 * i + 3]; + unsigned int x = p[0] << SHIFT_2 | (p[1] & MASK_BITS); + unsigned int y = p[2] << SHIFT_2 | (p[3] & MASK_BITS); + if (x == 0 || y == 0) + continue; + pos_x[finger_down_count] = x; + pos_y[finger_down_count] = y; + finger_down_count++; + } + + if (finger_down_count) { + if (finger_down_count == 2 && + (abs(pos_x[0] - pos_x[1]) < DELTA_MIN || + abs(pos_y[0] - pos_y[1]) < DELTA_MIN)) { + return 0; + } + + for (i = 0; i < finger_down_count; i++) { + if (data->chip->x_flip) + pos_x[i] = data->chip->touch_x_max - pos_x[i]; + if (data->chip->y_flip) + pos_y[i] = data->chip->touch_y_max - pos_y[i]; + + input_report_abs(data->in_dev, + ABS_MT_POSITION_X, pos_x[i]); + input_report_abs(data->in_dev, + ABS_MT_POSITION_Y, pos_y[i]); + input_mt_sync(data->in_dev); + } + } else + input_mt_sync(data->in_dev); + + input_sync(data->in_dev); + + return 0; +} +/** + * bu21013_gpio_irq() - gpio thread function for touch interrupt + * @irq: irq value + * @device_data: void pointer + * + * This gpio thread function for touch interrupt + * and returns irqreturn_t. + */ +static irqreturn_t bu21013_gpio_irq(int irq, void *device_data) +{ + struct bu21013_ts_data *data = device_data; + struct i2c_client *i2c = data->client; + int retval; + + do { + retval = bu21013_do_touch_report(data); + if (retval < 0) { + dev_err(&i2c->dev, "bu21013_do_touch_report failed\n"); + return IRQ_NONE; + } + + data->intr_pin = gpio_get_value(data->chip->touch_pin); + if (data->intr_pin == PEN_DOWN_INTR) + wait_event_timeout(data->wait, data->touch_stopped, + msecs_to_jiffies(2)); + } while (!data->intr_pin && !data->touch_stopped); + + return IRQ_HANDLED; +} + +/** + * bu21013_init_chip() - power on sequence for the bu21013 controller + * @data: device structure pointer + * + * This function is used to power on + * the bu21013 controller and returns integer. + */ +static int bu21013_init_chip(struct bu21013_ts_data *data) +{ + int retval; + struct i2c_client *i2c = data->client; + + retval = i2c_smbus_write_byte_data(i2c, BU21013_RESET_REG, + BU21013_RESET_ENABLE); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_RESET reg write failed\n"); + return retval; + } + msleep(RESET_DELAY); + + retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_0_7_REG, + BU21013_SENSORS_EN_0_7); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_SENSOR_0_7 reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_8_15_REG, + BU21013_SENSORS_EN_8_15); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_SENSOR_8_15 reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_SENSOR_16_23_REG, + BU21013_SENSORS_EN_16_23); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_SENSOR_16_23 reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_POS_MODE1_REG, + (BU21013_POS_MODE1_0 | BU21013_POS_MODE1_1)); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_POS_MODE1 reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_POS_MODE2_REG, + (BU21013_POS_MODE2_ZERO | BU21013_POS_MODE2_AVG1 | + BU21013_POS_MODE2_AVG2 | BU21013_POS_MODE2_EN_RAW | + BU21013_POS_MODE2_MULTI)); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_POS_MODE2 reg write failed\n"); + return retval; + } + + if (data->chip->ext_clk) + retval = i2c_smbus_write_byte_data(i2c, BU21013_CLK_MODE_REG, + (BU21013_CLK_MODE_EXT | BU21013_CLK_MODE_CALIB)); + else + retval = i2c_smbus_write_byte_data(i2c, BU21013_CLK_MODE_REG, + (BU21013_CLK_MODE_DIV | BU21013_CLK_MODE_CALIB)); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_CLK_MODE reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_IDLE_REG, + (BU21013_IDLET_0 | BU21013_IDLE_INTERMIT_EN)); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_IDLE reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_INT_MODE_REG, + BU21013_INT_MODE_LEVEL); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_INT_MODE reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_FILTER_REG, + (BU21013_DELTA_0_6 | + BU21013_FILTER_EN)); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_FILTER reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_TH_ON_REG, + BU21013_TH_ON_5); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_TH_ON reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_TH_OFF_REG, + BU21013_TH_OFF_4 | BU21013_TH_OFF_3); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_TH_OFF reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_GAIN_REG, + (BU21013_GAIN_0 | BU21013_GAIN_1)); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_GAIN reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_OFFSET_MODE_REG, + BU21013_OFFSET_MODE_DEFAULT); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_OFFSET_MODE reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_XY_EDGE_REG, + (BU21013_X_EDGE_0 | BU21013_X_EDGE_2 | + BU21013_Y_EDGE_1 | BU21013_Y_EDGE_3)); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_XY_EDGE reg write failed\n"); + return retval; + } + + retval = i2c_smbus_write_byte_data(i2c, BU21013_DONE_REG, + BU21013_DONE); + if (retval < 0) { + dev_err(&i2c->dev, "BU21013_REG_DONE reg write failed\n"); + return retval; + } + + return 0; +} + +/** + * bu21013_free_irq() - frees IRQ registered for touchscreen + * @bu21013_data: device structure pointer + * + * This function signals interrupt thread to stop processing and + * frees interrupt. + */ +static void bu21013_free_irq(struct bu21013_ts_data *bu21013_data) +{ + bu21013_data->touch_stopped = true; + wake_up(&bu21013_data->wait); + free_irq(bu21013_data->irq, bu21013_data); +} + +/** + * bu21013_cs_disable() - deconfigures the touch panel controller + * @bu21013_data: device structure pointer + * + * This function is used to deconfigure the chip selection + * for touch panel controller. + */ +static void bu21013_cs_disable(struct bu21013_ts_data *bu21013_data) +{ + int error; + + error = gpio_direction_output(bu21013_data->chip->cs_pin, 0); + if (error < 0) + dev_warn(&bu21013_data->client->dev, + "%s: gpio direction failed, error: %d\n", + __func__, error); + else + gpio_set_value(bu21013_data->chip->cs_pin, 0); + + gpio_free(bu21013_data->chip->cs_pin); +} + +#ifdef CONFIG_OF +static const struct bu21013_platform_device * +bu21013_parse_dt(struct device *dev) +{ + struct device_node *np = dev->of_node; + struct bu21013_platform_device *pdata; + + if (!np) { + dev_err(dev, "no device tree or platform data\n"); + return ERR_PTR(-EINVAL); + } + + pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); + if (!pdata) + return ERR_PTR(-ENOMEM); + + pdata->y_flip = pdata->x_flip = false; + + pdata->x_flip = of_property_read_bool(np, "rohm,flip-x"); + pdata->y_flip = of_property_read_bool(np, "rohm,flip-y"); + + of_property_read_u32(np, "rohm,touch-max-x", &pdata->touch_x_max); + of_property_read_u32(np, "rohm,touch-max-y", &pdata->touch_y_max); + + pdata->touch_pin = of_get_named_gpio(np, "touch-gpio", 0); + pdata->cs_pin = of_get_named_gpio(np, "reset-gpio", 0); + + pdata->ext_clk = false; + + return pdata; +} +#else +static inline const struct bu21013_platform_device * +bu21013_parse_dt(struct device *dev) +{ + dev_err(dev, "no platform data available\n"); + return ERR_PTR(-EINVAL); +} +#endif + +/** + * bu21013_probe() - initializes the i2c-client touchscreen driver + * @client: i2c client structure pointer + * @id: i2c device id pointer + * + * This function used to initializes the i2c-client touchscreen + * driver and returns integer. + */ +static int bu21013_probe(struct i2c_client *client, + const struct i2c_device_id *id) +{ + const struct bu21013_platform_device *pdata = + dev_get_platdata(&client->dev); + struct bu21013_ts_data *bu21013_data; + struct input_dev *in_dev; + int error; + + if (!i2c_check_functionality(client->adapter, + I2C_FUNC_SMBUS_BYTE_DATA)) { + dev_err(&client->dev, "i2c smbus byte data not supported\n"); + return -EIO; + } + + if (!pdata) { + pdata = bu21013_parse_dt(&client->dev); + if (IS_ERR(pdata)) + return PTR_ERR(pdata); + } + + if (!gpio_is_valid(pdata->touch_pin)) { + dev_err(&client->dev, "invalid touch_pin supplied\n"); + return -EINVAL; + } + + bu21013_data = kzalloc(sizeof(struct bu21013_ts_data), GFP_KERNEL); + in_dev = input_allocate_device(); + if (!bu21013_data || !in_dev) { + dev_err(&client->dev, "device memory alloc failed\n"); + error = -ENOMEM; + goto err_free_mem; + } + + bu21013_data->in_dev = in_dev; + bu21013_data->chip = pdata; + bu21013_data->client = client; + bu21013_data->irq = gpio_to_irq(pdata->touch_pin); + + bu21013_data->regulator = regulator_get(&client->dev, "avdd"); + if (IS_ERR(bu21013_data->regulator)) { + dev_err(&client->dev, "regulator_get failed\n"); + error = PTR_ERR(bu21013_data->regulator); + goto err_free_mem; + } + + error = regulator_enable(bu21013_data->regulator); + if (error < 0) { + dev_err(&client->dev, "regulator enable failed\n"); + goto err_put_regulator; + } + + bu21013_data->touch_stopped = false; + init_waitqueue_head(&bu21013_data->wait); + + /* configure the gpio pins */ + error = gpio_request_one(pdata->cs_pin, GPIOF_OUT_INIT_HIGH, + "touchp_reset"); + if (error < 0) { + dev_err(&client->dev, "Unable to request gpio reset_pin\n"); + goto err_disable_regulator; + } + + /* configure the touch panel controller */ + error = bu21013_init_chip(bu21013_data); + if (error) { + dev_err(&client->dev, "error in bu21013 config\n"); + goto err_cs_disable; + } + + /* register the device to input subsystem */ + in_dev->name = DRIVER_TP; + in_dev->id.bustype = BUS_I2C; + in_dev->dev.parent = &client->dev; + + __set_bit(EV_SYN, in_dev->evbit); + __set_bit(EV_KEY, in_dev->evbit); + __set_bit(EV_ABS, in_dev->evbit); + + input_set_abs_params(in_dev, ABS_MT_POSITION_X, 0, + pdata->touch_x_max, 0, 0); + input_set_abs_params(in_dev, ABS_MT_POSITION_Y, 0, + pdata->touch_y_max, 0, 0); + input_set_drvdata(in_dev, bu21013_data); + + error = request_threaded_irq(bu21013_data->irq, NULL, bu21013_gpio_irq, + IRQF_TRIGGER_FALLING | IRQF_SHARED | + IRQF_ONESHOT, + DRIVER_TP, bu21013_data); + if (error) { + dev_err(&client->dev, "request irq %d failed\n", + bu21013_data->irq); + goto err_cs_disable; + } + + error = input_register_device(in_dev); + if (error) { + dev_err(&client->dev, "failed to register input device\n"); + goto err_free_irq; + } + + device_init_wakeup(&client->dev, pdata->wakeup); + i2c_set_clientdata(client, bu21013_data); + + return 0; + +err_free_irq: + bu21013_free_irq(bu21013_data); +err_cs_disable: + bu21013_cs_disable(bu21013_data); +err_disable_regulator: + regulator_disable(bu21013_data->regulator); +err_put_regulator: + regulator_put(bu21013_data->regulator); +err_free_mem: + input_free_device(in_dev); + kfree(bu21013_data); + + return error; +} +/** + * bu21013_remove() - removes the i2c-client touchscreen driver + * @client: i2c client structure pointer + * + * This function uses to remove the i2c-client + * touchscreen driver and returns integer. + */ +static int bu21013_remove(struct i2c_client *client) +{ + struct bu21013_ts_data *bu21013_data = i2c_get_clientdata(client); + + bu21013_free_irq(bu21013_data); + + bu21013_cs_disable(bu21013_data); + + input_unregister_device(bu21013_data->in_dev); + + regulator_disable(bu21013_data->regulator); + regulator_put(bu21013_data->regulator); + + kfree(bu21013_data); + + return 0; +} + +#ifdef CONFIG_PM +/** + * bu21013_suspend() - suspend the touch screen controller + * @dev: pointer to device structure + * + * This function is used to suspend the + * touch panel controller and returns integer + */ +static int bu21013_suspend(struct device *dev) +{ + struct bu21013_ts_data *bu21013_data = dev_get_drvdata(dev); + struct i2c_client *client = bu21013_data->client; + + bu21013_data->touch_stopped = true; + if (device_may_wakeup(&client->dev)) + enable_irq_wake(bu21013_data->irq); + else + disable_irq(bu21013_data->irq); + + regulator_disable(bu21013_data->regulator); + + return 0; +} + +/** + * bu21013_resume() - resume the touch screen controller + * @dev: pointer to device structure + * + * This function is used to resume the touch panel + * controller and returns integer. + */ +static int bu21013_resume(struct device *dev) +{ + struct bu21013_ts_data *bu21013_data = dev_get_drvdata(dev); + struct i2c_client *client = bu21013_data->client; + int retval; + + retval = regulator_enable(bu21013_data->regulator); + if (retval < 0) { + dev_err(&client->dev, "bu21013 regulator enable failed\n"); + return retval; + } + + retval = bu21013_init_chip(bu21013_data); + if (retval < 0) { + dev_err(&client->dev, "bu21013 controller config failed\n"); + return retval; + } + + bu21013_data->touch_stopped = false; + + if (device_may_wakeup(&client->dev)) + disable_irq_wake(bu21013_data->irq); + else + enable_irq(bu21013_data->irq); + + return 0; +} + +static const struct dev_pm_ops bu21013_dev_pm_ops = { + .suspend = bu21013_suspend, + .resume = bu21013_resume, +}; +#endif + +static const struct i2c_device_id bu21013_id[] = { + { DRIVER_TP, 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, bu21013_id); + +static struct i2c_driver bu21013_driver = { + .driver = { + .name = DRIVER_TP, +#ifdef CONFIG_PM + .pm = &bu21013_dev_pm_ops, +#endif + }, + .probe = bu21013_probe, + .remove = bu21013_remove, + .id_table = bu21013_id, +}; + +module_i2c_driver(bu21013_driver); + +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Naveen Kumar G <naveen.gaddipati@stericsson.com>"); +MODULE_DESCRIPTION("bu21013 touch screen controller driver"); |