diff options
Diffstat (limited to 'drivers/misc/eeprom/Kconfig')
| -rw-r--r-- | drivers/misc/eeprom/Kconfig | 114 |
1 files changed, 114 insertions, 0 deletions
diff --git a/drivers/misc/eeprom/Kconfig b/drivers/misc/eeprom/Kconfig new file mode 100644 index 000000000..d382b13c2 --- /dev/null +++ b/drivers/misc/eeprom/Kconfig @@ -0,0 +1,114 @@ +menu "EEPROM support" + +config EEPROM_AT24 + tristate "I2C EEPROMs / RAMs / ROMs from most vendors" + depends on I2C && SYSFS + select NVMEM + select REGMAP_I2C + help + Enable this driver to get read/write support to most I2C EEPROMs + and compatible devices like FRAMs, SRAMs, ROMs etc. After you + configure the driver to know about each chip on your target + board. Use these generic chip names, instead of vendor-specific + ones like at24c64, 24lc02 or fm24c04: + + 24c00, 24c01, 24c02, spd (readonly 24c02), 24c04, 24c08, + 24c16, 24c32, 24c64, 24c128, 24c256, 24c512, 24c1024, 24c2048 + + Unless you like data loss puzzles, always be sure that any chip + you configure as a 24c32 (32 kbit) or larger is NOT really a + 24c16 (16 kbit) or smaller, and vice versa. Marking the chip + as read-only won't help recover from this. Also, if your chip + has any software write-protect mechanism you may want to review the + code to make sure this driver won't turn it on by accident. + + If you use this with an SMBus adapter instead of an I2C adapter, + full functionality is not available. Only smaller devices are + supported (24c16 and below, max 4 kByte). + + This driver can also be built as a module. If so, the module + will be called at24. + +config EEPROM_AT25 + tristate "SPI EEPROMs from most vendors" + depends on SPI && SYSFS + select NVMEM + help + Enable this driver to get read/write support to most SPI EEPROMs, + after you configure the board init code to know about each eeprom + on your target board. + + This driver can also be built as a module. If so, the module + will be called at25. + +config EEPROM_LEGACY + tristate "Old I2C EEPROM reader" + depends on I2C && SYSFS + help + If you say yes here you get read-only access to the EEPROM data + available on modern memory DIMMs and Sony Vaio laptops via I2C. Such + EEPROMs could theoretically be available on other devices as well. + + This driver can also be built as a module. If so, the module + will be called eeprom. + +config EEPROM_MAX6875 + tristate "Maxim MAX6874/5 power supply supervisor" + depends on I2C + help + If you say yes here you get read-only support for the user EEPROM of + the Maxim MAX6874/5 EEPROM-programmable, quad power-supply + sequencer/supervisor. + + All other features of this chip should be accessed via i2c-dev. + + This driver can also be built as a module. If so, the module + will be called max6875. + + +config EEPROM_93CX6 + tristate "EEPROM 93CX6 support" + help + This is a driver for the EEPROM chipsets 93c46 and 93c66. + The driver supports both read as well as write commands. + + If unsure, say N. + +config EEPROM_93XX46 + tristate "Microwire EEPROM 93XX46 support" + depends on SPI && SYSFS + select REGMAP + select NVMEM + help + Driver for the microwire EEPROM chipsets 93xx46x. The driver + supports both read and write commands and also the command to + erase the whole EEPROM. + + This driver can also be built as a module. If so, the module + will be called eeprom_93xx46. + + If unsure, say N. + +config EEPROM_DIGSY_MTC_CFG + bool "DigsyMTC display configuration EEPROMs device" + depends on GPIO_MPC5200 && SPI_GPIO + help + This option enables access to display configuration EEPROMs + on digsy_mtc board. You have to additionally select Microwire + EEPROM 93XX46 driver. sysfs entries will be created for that + EEPROM allowing to read/write the configuration data or to + erase the whole EEPROM. + + If unsure, say N. + +config EEPROM_IDT_89HPESX + tristate "IDT 89HPESx PCIe-swtiches EEPROM / CSR support" + depends on I2C && SYSFS + help + Enable this driver to get read/write access to EEPROM / CSRs + over IDT PCIe-swtich i2c-slave interface. + + This driver can also be built as a module. If so, the module + will be called idt_89hpesx. + +endmenu |