diff options
Diffstat (limited to 'drivers/net/can/Kconfig')
-rw-r--r-- | drivers/net/can/Kconfig | 177 |
1 files changed, 177 insertions, 0 deletions
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig new file mode 100644 index 000000000..7cdd0cead --- /dev/null +++ b/drivers/net/can/Kconfig @@ -0,0 +1,177 @@ +menu "CAN Device Drivers" + +config CAN_VCAN + tristate "Virtual Local CAN Interface (vcan)" + ---help--- + Similar to the network loopback devices, vcan offers a + virtual local CAN interface. + + This driver can also be built as a module. If so, the module + will be called vcan. + +config CAN_VXCAN + tristate "Virtual CAN Tunnel (vxcan)" + ---help--- + Similar to the virtual ethernet driver veth, vxcan implements a + local CAN traffic tunnel between two virtual CAN network devices. + When creating a vxcan, two vxcan devices are created as pair. + When one end receives the packet it appears on its pair and vice + versa. The vxcan can be used for cross namespace communication. + + In opposite to vcan loopback devices the vxcan only forwards CAN + frames to its pair and does *not* provide a local echo of sent + CAN frames. To disable a potential echo in af_can.c the vxcan driver + announces IFF_ECHO in the interface flags. To have a clean start + in each namespace the CAN GW hop counter is set to zero. + + This driver can also be built as a module. If so, the module + will be called vxcan. + +config CAN_SLCAN + tristate "Serial / USB serial CAN Adaptors (slcan)" + depends on TTY + ---help--- + CAN driver for several 'low cost' CAN interfaces that are attached + via serial lines or via USB-to-serial adapters using the LAWICEL + ASCII protocol. The driver implements the tty linediscipline N_SLCAN. + + As only the sending and receiving of CAN frames is implemented, this + driver should work with the (serial/USB) CAN hardware from: + www.canusb.com / www.can232.com / www.mictronics.de / www.canhack.de + + Userspace tools to attach the SLCAN line discipline (slcan_attach, + slcand) can be found in the can-utils at the SocketCAN SVN, see + http://developer.berlios.de/projects/socketcan for details. + + The slcan driver supports up to 10 CAN netdevices by default which + can be changed by the 'maxdev=xx' module option. This driver can + also be built as a module. If so, the module will be called slcan. + +config CAN_DEV + tristate "Platform CAN drivers with Netlink support" + default y + ---help--- + Enables the common framework for platform CAN drivers with Netlink + support. This is the standard library for CAN drivers. + If unsure, say Y. + +if CAN_DEV + +config CAN_CALC_BITTIMING + bool "CAN bit-timing calculation" + default y + ---help--- + If enabled, CAN bit-timing parameters will be calculated for the + bit-rate specified via Netlink argument "bitrate" when the device + get started. This works fine for the most common CAN controllers + with standard bit-rates but may fail for exotic bit-rates or CAN + source clock frequencies. Disabling saves some space, but then the + bit-timing parameters must be specified directly using the Netlink + arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw". + If unsure, say Y. + +config CAN_LEDS + bool "Enable LED triggers for Netlink based drivers" + depends on LEDS_CLASS + # The netdev trigger (LEDS_TRIGGER_NETDEV) should be able to do + # everything that this driver is doing. This is marked as broken + # because it uses stuff that is intended to be changed or removed. + # Please consider switching to the netdev trigger and confirm it + # fulfills your needs instead of fixing this driver. + depends on BROKEN + select LEDS_TRIGGERS + ---help--- + This option adds two LED triggers for packet receive and transmit + events on each supported CAN device. + + Say Y here if you are working on a system with led-class supported + LEDs and you want to use them as canbus activity indicators. + +config CAN_AT91 + tristate "Atmel AT91 onchip CAN controller" + depends on (ARCH_AT91 || COMPILE_TEST) && HAS_IOMEM + ---help--- + This is a driver for the SoC CAN controller in Atmel's AT91SAM9263 + and AT91SAM9X5 processors. + +config CAN_FLEXCAN + tristate "Support for Freescale FLEXCAN based chips" + depends on ARM || PPC + ---help--- + Say Y here if you want to support for Freescale FlexCAN. + +config CAN_GRCAN + tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices" + depends on OF && HAS_DMA + ---help--- + Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN. + Note that the driver supports little endian, even though little + endian syntheses of the cores would need some modifications on + the hardware level to work. + +config CAN_JANZ_ICAN3 + tristate "Janz VMOD-ICAN3 Intelligent CAN controller" + depends on MFD_JANZ_CMODIO + ---help--- + Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which + connects to a MODULbus carrier board. + + This driver can also be built as a module. If so, the module will be + called janz-ican3.ko. + +config CAN_SUN4I + tristate "Allwinner A10 CAN controller" + depends on MACH_SUN4I || MACH_SUN7I || COMPILE_TEST + ---help--- + Say Y here if you want to use CAN controller found on Allwinner + A10/A20 SoCs. + + To compile this driver as a module, choose M here: the module will + be called sun4i_can. + +config CAN_TI_HECC + depends on ARM + tristate "TI High End CAN Controller" + ---help--- + Driver for TI HECC (High End CAN Controller) module found on many + TI devices. The device specifications are available from www.ti.com + +config CAN_XILINXCAN + tristate "Xilinx CAN" + depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST + depends on COMMON_CLK && HAS_IOMEM + ---help--- + Xilinx CAN driver. This driver supports both soft AXI CAN IP and + Zynq CANPS IP. + +config PCH_CAN + tristate "Intel EG20T PCH CAN controller" + depends on PCI && (X86_32 || COMPILE_TEST) + ---help--- + This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which + is an IOH for x86 embedded processor (Intel Atom E6xx series). + This driver can access CAN bus. + +source "drivers/net/can/c_can/Kconfig" +source "drivers/net/can/cc770/Kconfig" +source "drivers/net/can/ifi_canfd/Kconfig" +source "drivers/net/can/m_can/Kconfig" +source "drivers/net/can/mscan/Kconfig" +source "drivers/net/can/peak_canfd/Kconfig" +source "drivers/net/can/rcar/Kconfig" +source "drivers/net/can/sja1000/Kconfig" +source "drivers/net/can/softing/Kconfig" +source "drivers/net/can/spi/Kconfig" +source "drivers/net/can/usb/Kconfig" + +endif + +config CAN_DEBUG_DEVICES + bool "CAN devices debugging messages" + ---help--- + Say Y here if you want the CAN device drivers to produce a bunch of + debug messages to the system log. Select this if you are having + a problem with CAN support and want to see more of what is going + on. + +endmenu |