diff options
Diffstat (limited to 'drivers/net/hamradio/Kconfig')
| -rw-r--r-- | drivers/net/hamradio/Kconfig | 193 |
1 files changed, 193 insertions, 0 deletions
diff --git a/drivers/net/hamradio/Kconfig b/drivers/net/hamradio/Kconfig new file mode 100644 index 000000000..bf5e59687 --- /dev/null +++ b/drivers/net/hamradio/Kconfig @@ -0,0 +1,193 @@ +config MKISS + tristate "Serial port KISS driver" + depends on AX25 && TTY + select CRC16 + ---help--- + KISS is a protocol used for the exchange of data between a computer + and a Terminal Node Controller (a small embedded system commonly + used for networking over AX.25 amateur radio connections; it + connects the computer's serial port with the radio's microphone + input and speaker output). + + Although KISS is less advanced than the 6pack protocol, it has + the advantage that it is already supported by most modern TNCs + without the need for a firmware upgrade. + + To compile this driver as a module, choose M here: the module + will be called mkiss. + +config 6PACK + tristate "Serial port 6PACK driver" + depends on AX25 && TTY + ---help--- + 6pack is a transmission protocol for the data exchange between your + PC and your TNC (the Terminal Node Controller acts as a kind of + modem connecting your computer's serial port to your radio's + microphone input and speaker output). This protocol can be used as + an alternative to KISS for networking over AX.25 amateur radio + connections, but it has some extended functionality. + + Note that this driver is still experimental and might cause + problems. For details about the features and the usage of the + driver, read <file:Documentation/networking/6pack.txt>. + + To compile this driver as a module, choose M here: the module + will be called 6pack. + +config BPQETHER + tristate "BPQ Ethernet driver" + depends on AX25 + help + AX.25 is the protocol used for computer communication over amateur + radio. If you say Y here, you will be able to send and receive AX.25 + traffic over Ethernet (also called "BPQ AX.25"), which could be + useful if some other computer on your local network has a direct + amateur radio connection. + +config DMASCC + tristate "High-speed (DMA) SCC driver for AX.25" + depends on ISA && AX25 && BROKEN_ON_SMP && ISA_DMA_API + ---help--- + This is a driver for high-speed SCC boards, i.e. those supporting + DMA on one port. You usually use those boards to connect your + computer to an amateur radio modem (such as the WA4DSY 56kbps + modem), in order to send and receive AX.25 packet radio network + traffic. + + Currently, this driver supports Ottawa PI/PI2, Paccomm/Gracilis + PackeTwin, and S5SCC/DMA boards. They are detected automatically. + If you have one of these cards, say Y here and read the AX25-HOWTO, + available from <http://www.tldp.org/docs.html#howto>. + + This driver can operate multiple boards simultaneously. If you + compile it as a module (by saying M instead of Y), it will be called + dmascc. If you don't pass any parameter to the driver, all + possible I/O addresses are probed. This could irritate other devices + that are currently not in use. You may specify the list of addresses + to be probed by "dmascc.io=addr1,addr2,..." (when compiled into the + kernel image) or "io=addr1,addr2,..." (when loaded as a module). The + network interfaces will be called dmascc0 and dmascc1 for the board + detected first, dmascc2 and dmascc3 for the second one, and so on. + + Before you configure each interface with ifconfig, you MUST set + certain parameters, such as channel access timing, clock mode, and + DMA channel. This is accomplished with a small utility program, + dmascc_cfg, available at + <http://www.linux-ax25.org/wiki/Ax25-tools>. Please be sure to + get at least version 1.27 of dmascc_cfg, as older versions will not + work with the current driver. + +config SCC + tristate "Z8530 SCC driver" + depends on ISA && AX25 && ISA_DMA_API + ---help--- + These cards are used to connect your Linux box to an amateur radio + in order to communicate with other computers. If you want to use + this, read <file:Documentation/networking/z8530drv.txt> and the + AX25-HOWTO, available from + <http://www.tldp.org/docs.html#howto>. Also make sure to say Y + to "Amateur Radio AX.25 Level 2" support. + + To compile this driver as a module, choose M here: the module + will be called scc. + +config SCC_DELAY + bool "additional delay for PA0HZP OptoSCC compatible boards" + depends on SCC + help + Say Y here if you experience problems with the SCC driver not + working properly; please read + <file:Documentation/networking/z8530drv.txt> for details. + + If unsure, say N. + +config SCC_TRXECHO + bool "support for TRX that feedback the tx signal to rx" + depends on SCC + help + Some transmitters feed the transmitted signal back to the receive + line. Say Y here to foil this by explicitly disabling the receiver + during data transmission. + + If in doubt, say Y. + +config BAYCOM_SER_FDX + tristate "BAYCOM ser12 fullduplex driver for AX.25" + depends on AX25 && !S390 + select CRC_CCITT + ---help--- + This is one of two drivers for Baycom style simple amateur radio + modems that connect to a serial interface. The driver supports the + ser12 design in full-duplex mode. In addition, it allows the + baudrate to be set between 300 and 4800 baud (however not all modems + support all baudrates). This is the preferred driver. The next + driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old + driver and still provided in case this driver does not work with + your serial interface chip. To configure the driver, use the sethdlc + utility available in the standard ax25 utilities package. For + information on the modems, see <http://www.baycom.de/> and + <file:Documentation/networking/baycom.txt>. + + To compile this driver as a module, choose M here: the module + will be called baycom_ser_fdx. This is recommended. + +config BAYCOM_SER_HDX + tristate "BAYCOM ser12 halfduplex driver for AX.25" + depends on AX25 && !S390 + select CRC_CCITT + ---help--- + This is one of two drivers for Baycom style simple amateur radio + modems that connect to a serial interface. The driver supports the + ser12 design in half-duplex mode. This is the old driver. It is + still provided in case your serial interface chip does not work with + the full-duplex driver. This driver is deprecated. To configure + the driver, use the sethdlc utility available in the standard ax25 + utilities package. For information on the modems, see + <http://www.baycom.de/> and + <file:Documentation/networking/baycom.txt>. + + To compile this driver as a module, choose M here: the module + will be called baycom_ser_hdx. This is recommended. + +config BAYCOM_PAR + tristate "BAYCOM picpar and par96 driver for AX.25" + depends on PARPORT && AX25 + select CRC_CCITT + ---help--- + This is a driver for Baycom style simple amateur radio modems that + connect to a parallel interface. The driver supports the picpar and + par96 designs. To configure the driver, use the sethdlc utility + available in the standard ax25 utilities package. For information on + the modems, see <http://www.baycom.de/> and the file + <file:Documentation/networking/baycom.txt>. + + To compile this driver as a module, choose M here: the module + will be called baycom_par. This is recommended. + +config BAYCOM_EPP + tristate "BAYCOM epp driver for AX.25" + depends on PARPORT && AX25 && !64BIT + select CRC_CCITT + ---help--- + This is a driver for Baycom style simple amateur radio modems that + connect to a parallel interface. The driver supports the EPP + designs. To configure the driver, use the sethdlc utility available + in the standard ax25 utilities package. For information on the + modems, see <http://www.baycom.de/> and the file + <file:Documentation/networking/baycom.txt>. + + To compile this driver as a module, choose M here: the module + will be called baycom_epp. This is recommended. + +config YAM + tristate "YAM driver for AX.25" + depends on AX25 && !S390 + help + The YAM is a modem for packet radio which connects to the serial + port and includes some of the functions of a Terminal Node + Controller. If you have one of those, say Y here. + + To compile this driver as a module, choose M here: the module + will be called yam. + + |