1 files changed, 897 insertions, 0 deletions

diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
new file mode 100644
index 000000000..901f525c8
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
@@ -0,0 +1,897 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2017, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+
+#include <dt-bindings/phy/phy-qcom-qusb2.h>
+
+#define QUSB2PHY_PLL_TEST		0x04
+#define CLK_REF_SEL			BIT(7)
+
+#define QUSB2PHY_PLL_TUNE		0x08
+#define QUSB2PHY_PLL_USER_CTL1		0x0c
+#define QUSB2PHY_PLL_USER_CTL2		0x10
+#define QUSB2PHY_PLL_AUTOPGM_CTL1	0x1c
+#define QUSB2PHY_PLL_PWR_CTRL		0x18
+
+/* QUSB2PHY_PLL_STATUS register bits */
+#define PLL_LOCKED			BIT(5)
+
+/* QUSB2PHY_PLL_COMMON_STATUS_ONE register bits */
+#define CORE_READY_STATUS		BIT(0)
+
+/* QUSB2PHY_PORT_POWERDOWN register bits */
+#define CLAMP_N_EN			BIT(5)
+#define FREEZIO_N			BIT(1)
+#define POWER_DOWN			BIT(0)
+
+/* QUSB2PHY_PWR_CTRL1 register bits */
+#define PWR_CTRL1_VREF_SUPPLY_TRIM	BIT(5)
+#define PWR_CTRL1_CLAMP_N_EN		BIT(1)
+
+#define QUSB2PHY_REFCLK_ENABLE		BIT(0)
+
+#define PHY_CLK_SCHEME_SEL		BIT(0)
+
+/* QUSB2PHY_INTR_CTRL register bits */
+#define DMSE_INTR_HIGH_SEL			BIT(4)
+#define DPSE_INTR_HIGH_SEL			BIT(3)
+#define CHG_DET_INTR_EN				BIT(2)
+#define DMSE_INTR_EN				BIT(1)
+#define DPSE_INTR_EN				BIT(0)
+
+/* QUSB2PHY_PLL_CORE_INPUT_OVERRIDE register bits */
+#define CORE_PLL_EN_FROM_RESET			BIT(4)
+#define CORE_RESET				BIT(5)
+#define CORE_RESET_MUX				BIT(6)
+
+/* QUSB2PHY_IMP_CTRL1 register bits */
+#define IMP_RES_OFFSET_MASK			GENMASK(5, 0)
+#define IMP_RES_OFFSET_SHIFT			0x0
+
+/* QUSB2PHY_PORT_TUNE1 register bits */
+#define HSTX_TRIM_MASK				GENMASK(7, 4)
+#define HSTX_TRIM_SHIFT				0x4
+#define PREEMPH_WIDTH_HALF_BIT			BIT(2)
+#define PREEMPHASIS_EN_MASK			GENMASK(1, 0)
+#define PREEMPHASIS_EN_SHIFT			0x0
+
+#define QUSB2PHY_PLL_ANALOG_CONTROLS_TWO	0x04
+#define QUSB2PHY_PLL_CLOCK_INVERTERS		0x18c
+#define QUSB2PHY_PLL_CMODE			0x2c
+#define QUSB2PHY_PLL_LOCK_DELAY			0x184
+#define QUSB2PHY_PLL_DIGITAL_TIMERS_TWO		0xb4
+#define QUSB2PHY_PLL_BIAS_CONTROL_1		0x194
+#define QUSB2PHY_PLL_BIAS_CONTROL_2		0x198
+#define QUSB2PHY_PWR_CTRL2			0x214
+#define QUSB2PHY_IMP_CTRL1			0x220
+#define QUSB2PHY_IMP_CTRL2			0x224
+#define QUSB2PHY_CHG_CTRL2			0x23c
+
+struct qusb2_phy_init_tbl {
+	unsigned int offset;
+	unsigned int val;
+	/*
+	 * register part of layout ?
+	 * if yes, then offset gives index in the reg-layout
+	 */
+	int in_layout;
+};
+
+#define QUSB2_PHY_INIT_CFG(o, v) \
+	{			\
+		.offset = o,	\
+		.val = v,	\
+	}
+
+#define QUSB2_PHY_INIT_CFG_L(o, v) \
+	{			\
+		.offset = o,	\
+		.val = v,	\
+		.in_layout = 1,	\
+	}
+
+/* set of registers with offsets different per-PHY */
+enum qusb2phy_reg_layout {
+	QUSB2PHY_PLL_CORE_INPUT_OVERRIDE,
+	QUSB2PHY_PLL_STATUS,
+	QUSB2PHY_PORT_TUNE1,
+	QUSB2PHY_PORT_TUNE2,
+	QUSB2PHY_PORT_TUNE3,
+	QUSB2PHY_PORT_TUNE4,
+	QUSB2PHY_PORT_TUNE5,
+	QUSB2PHY_PORT_TEST1,
+	QUSB2PHY_PORT_TEST2,
+	QUSB2PHY_PORT_POWERDOWN,
+	QUSB2PHY_INTR_CTRL,
+};
+
+static const unsigned int msm8996_regs_layout[] = {
+	[QUSB2PHY_PLL_STATUS]		= 0x38,
+	[QUSB2PHY_PORT_TUNE1]		= 0x80,
+	[QUSB2PHY_PORT_TUNE2]		= 0x84,
+	[QUSB2PHY_PORT_TUNE3]		= 0x88,
+	[QUSB2PHY_PORT_TUNE4]		= 0x8c,
+	[QUSB2PHY_PORT_TUNE5]		= 0x90,
+	[QUSB2PHY_PORT_TEST1]		= 0xb8,
+	[QUSB2PHY_PORT_TEST2]		= 0x9c,
+	[QUSB2PHY_PORT_POWERDOWN]	= 0xb4,
+	[QUSB2PHY_INTR_CTRL]		= 0xbc,
+};
+
+static const struct qusb2_phy_init_tbl msm8996_init_tbl[] = {
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xf8),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0xb3),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0x83),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0xc0),
+
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_TUNE, 0x30),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL1, 0x79),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_USER_CTL2, 0x21),
+
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TEST2, 0x14),
+
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_AUTOPGM_CTL1, 0x9f),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00),
+};
+
+static const unsigned int sdm845_regs_layout[] = {
+	[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8,
+	[QUSB2PHY_PLL_STATUS]		= 0x1a0,
+	[QUSB2PHY_PORT_TUNE1]		= 0x240,
+	[QUSB2PHY_PORT_TUNE2]		= 0x244,
+	[QUSB2PHY_PORT_TUNE3]		= 0x248,
+	[QUSB2PHY_PORT_TUNE4]		= 0x24c,
+	[QUSB2PHY_PORT_TUNE5]		= 0x250,
+	[QUSB2PHY_PORT_TEST1]		= 0x254,
+	[QUSB2PHY_PORT_TEST2]		= 0x258,
+	[QUSB2PHY_PORT_POWERDOWN]	= 0x210,
+	[QUSB2PHY_INTR_CTRL]		= 0x230,
+};
+
+static const struct qusb2_phy_init_tbl sdm845_init_tbl[] = {
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x03),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_1, 0x40),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_BIAS_CONTROL_2, 0x20),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PWR_CTRL2, 0x21),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL1, 0x0),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_IMP_CTRL2, 0x58),
+
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0x30),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x29),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE3, 0xca),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE4, 0x04),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE5, 0x03),
+
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_CHG_CTRL2, 0x0),
+};
+
+struct qusb2_phy_cfg {
+	const struct qusb2_phy_init_tbl *tbl;
+	/* number of entries in the table */
+	unsigned int tbl_num;
+	/* offset to PHY_CLK_SCHEME register in TCSR map */
+	unsigned int clk_scheme_offset;
+
+	/* array of registers with different offsets */
+	const unsigned int *regs;
+	unsigned int mask_core_ready;
+	unsigned int disable_ctrl;
+	unsigned int autoresume_en;
+
+	/* true if PHY has PLL_TEST register to select clk_scheme */
+	bool has_pll_test;
+
+	/* true if TUNE1 register must be updated by fused value, else TUNE2 */
+	bool update_tune1_with_efuse;
+
+	/* true if PHY has PLL_CORE_INPUT_OVERRIDE register to reset PLL */
+	bool has_pll_override;
+};
+
+static const struct qusb2_phy_cfg msm8996_phy_cfg = {
+	.tbl		= msm8996_init_tbl,
+	.tbl_num	= ARRAY_SIZE(msm8996_init_tbl),
+	.regs		= msm8996_regs_layout,
+
+	.has_pll_test	= true,
+	.disable_ctrl	= (CLAMP_N_EN | FREEZIO_N | POWER_DOWN),
+	.mask_core_ready = PLL_LOCKED,
+	.autoresume_en	 = BIT(3),
+};
+
+static const struct qusb2_phy_cfg sdm845_phy_cfg = {
+	.tbl		= sdm845_init_tbl,
+	.tbl_num	= ARRAY_SIZE(sdm845_init_tbl),
+	.regs		= sdm845_regs_layout,
+
+	.disable_ctrl	= (PWR_CTRL1_VREF_SUPPLY_TRIM | PWR_CTRL1_CLAMP_N_EN |
+			   POWER_DOWN),
+	.mask_core_ready = CORE_READY_STATUS,
+	.has_pll_override = true,
+	.autoresume_en	  = BIT(0),
+	.update_tune1_with_efuse = true,
+};
+
+static const char * const qusb2_phy_vreg_names[] = {
+	"vdda-pll", "vdda-phy-dpdm",
+};
+
+#define QUSB2_NUM_VREGS		ARRAY_SIZE(qusb2_phy_vreg_names)
+
+/**
+ * struct qusb2_phy - structure holding qusb2 phy attributes
+ *
+ * @phy: generic phy
+ * @base: iomapped memory space for qubs2 phy
+ *
+ * @cfg_ahb_clk: AHB2PHY interface clock
+ * @ref_clk: phy reference clock
+ * @iface_clk: phy interface clock
+ * @phy_reset: phy reset control
+ * @vregs: regulator supplies bulk data
+ *
+ * @tcsr: TCSR syscon register map
+ * @cell: nvmem cell containing phy tuning value
+ *
+ * @override_imp_res_offset: PHY should use different rescode offset
+ * @imp_res_offset_value: rescode offset to be updated in IMP_CTRL1 register
+ * @override_hstx_trim: PHY should use different HSTX o/p current value
+ * @hstx_trim_value: HSTX_TRIM value to be updated in TUNE1 register
+ * @override_preemphasis: PHY should use different pre-amphasis amplitude
+ * @preemphasis_level: Amplitude Pre-Emphasis to be updated in TUNE1 register
+ * @override_preemphasis_width: PHY should use different pre-emphasis duration
+ * @preemphasis_width: half/full-width Pre-Emphasis updated via TUNE1
+ *
+ * @cfg: phy config data
+ * @has_se_clk_scheme: indicate if PHY has single-ended ref clock scheme
+ * @phy_initialized: indicate if PHY has been initialized
+ * @mode: current PHY mode
+ */
+struct qusb2_phy {
+	struct phy *phy;
+	void __iomem *base;
+
+	struct clk *cfg_ahb_clk;
+	struct clk *ref_clk;
+	struct clk *iface_clk;
+	struct reset_control *phy_reset;
+	struct regulator_bulk_data vregs[QUSB2_NUM_VREGS];
+
+	struct regmap *tcsr;
+	struct nvmem_cell *cell;
+
+	bool override_imp_res_offset;
+	u8 imp_res_offset_value;
+	bool override_hstx_trim;
+	u8 hstx_trim_value;
+	bool override_preemphasis;
+	u8 preemphasis_level;
+	bool override_preemphasis_width;
+	u8 preemphasis_width;
+
+	const struct qusb2_phy_cfg *cfg;
+	bool has_se_clk_scheme;
+	bool phy_initialized;
+	enum phy_mode mode;
+};
+
+static inline void qusb2_write_mask(void __iomem *base, u32 offset,
+				    u32 val, u32 mask)
+{
+	u32 reg;
+
+	reg = readl(base + offset);
+	reg &= ~mask;
+	reg |= val & mask;
+	writel(reg, base + offset);
+
+	/* Ensure above write is completed */
+	readl(base + offset);
+}
+
+static inline void qusb2_setbits(void __iomem *base, u32 offset, u32 val)
+{
+	u32 reg;
+
+	reg = readl(base + offset);
+	reg |= val;
+	writel(reg, base + offset);
+
+	/* Ensure above write is completed */
+	readl(base + offset);
+}
+
+static inline void qusb2_clrbits(void __iomem *base, u32 offset, u32 val)
+{
+	u32 reg;
+
+	reg = readl(base + offset);
+	reg &= ~val;
+	writel(reg, base + offset);
+
+	/* Ensure above write is completed */
+	readl(base + offset);
+}
+
+static inline
+void qcom_qusb2_phy_configure(void __iomem *base,
+			      const unsigned int *regs,
+			      const struct qusb2_phy_init_tbl tbl[], int num)
+{
+	int i;
+
+	for (i = 0; i < num; i++) {
+		if (tbl[i].in_layout)
+			writel(tbl[i].val, base + regs[tbl[i].offset]);
+		else
+			writel(tbl[i].val, base + tbl[i].offset);
+	}
+}
+
+/*
+ * Update board specific PHY tuning override values if specified from
+ * device tree.
+ */
+static void qusb2_phy_override_phy_params(struct qusb2_phy *qphy)
+{
+	const struct qusb2_phy_cfg *cfg = qphy->cfg;
+
+	if (qphy->override_imp_res_offset)
+		qusb2_write_mask(qphy->base, QUSB2PHY_IMP_CTRL1,
+			     qphy->imp_res_offset_value << IMP_RES_OFFSET_SHIFT,
+			     IMP_RES_OFFSET_MASK);
+
+	if (qphy->override_hstx_trim)
+		qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1],
+				 qphy->hstx_trim_value << HSTX_TRIM_SHIFT,
+				 HSTX_TRIM_MASK);
+
+	if (qphy->override_preemphasis)
+		qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1],
+				qphy->preemphasis_level << PREEMPHASIS_EN_SHIFT,
+				PREEMPHASIS_EN_MASK);
+
+	if (qphy->override_preemphasis_width) {
+		if (qphy->preemphasis_width ==
+		    QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT)
+			qusb2_setbits(qphy->base,
+				      cfg->regs[QUSB2PHY_PORT_TUNE1],
+				      PREEMPH_WIDTH_HALF_BIT);
+		else
+			qusb2_clrbits(qphy->base,
+				      cfg->regs[QUSB2PHY_PORT_TUNE1],
+				      PREEMPH_WIDTH_HALF_BIT);
+	}
+}
+
+/*
+ * Fetches HS Tx tuning value from nvmem and sets the
+ * QUSB2PHY_PORT_TUNE1/2 register.
+ * For error case, skip setting the value and use the default value.
+ */
+static void qusb2_phy_set_tune2_param(struct qusb2_phy *qphy)
+{
+	struct device *dev = &qphy->phy->dev;
+	const struct qusb2_phy_cfg *cfg = qphy->cfg;
+	u8 *val, hstx_trim;
+
+	/* efuse register is optional */
+	if (!qphy->cell)
+		return;
+
+	/*
+	 * Read efuse register having TUNE2/1 parameter's high nibble.
+	 * If efuse register shows value as 0x0 (indicating value is not
+	 * fused), or if we fail to find a valid efuse register setting,
+	 * then use default value for high nibble that we have already
+	 * set while configuring the phy.
+	 */
+	val = nvmem_cell_read(qphy->cell, NULL);
+	if (IS_ERR(val)) {
+		dev_dbg(dev, "failed to read a valid hs-tx trim value\n");
+		return;
+	}
+	hstx_trim = val[0];
+	kfree(val);
+	if (!hstx_trim) {
+		dev_dbg(dev, "failed to read a valid hs-tx trim value\n");
+		return;
+	}
+
+	/* Fused TUNE1/2 value is the higher nibble only */
+	if (cfg->update_tune1_with_efuse)
+		qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE1],
+				 hstx_trim << HSTX_TRIM_SHIFT, HSTX_TRIM_MASK);
+	else
+		qusb2_write_mask(qphy->base, cfg->regs[QUSB2PHY_PORT_TUNE2],
+				 hstx_trim << HSTX_TRIM_SHIFT, HSTX_TRIM_MASK);
+}
+
+static int qusb2_phy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+	struct qusb2_phy *qphy = phy_get_drvdata(phy);
+
+	qphy->mode = mode;
+
+	return 0;
+}
+
+static int __maybe_unused qusb2_phy_runtime_suspend(struct device *dev)
+{
+	struct qusb2_phy *qphy = dev_get_drvdata(dev);
+	const struct qusb2_phy_cfg *cfg = qphy->cfg;
+	u32 intr_mask;
+
+	dev_vdbg(dev, "Suspending QUSB2 Phy, mode:%d\n", qphy->mode);
+
+	if (!qphy->phy_initialized) {
+		dev_vdbg(dev, "PHY not initialized, bailing out\n");
+		return 0;
+	}
+
+	/*
+	 * Enable DP/DM interrupts to detect line state changes based on current
+	 * speed. In other words, enable the triggers _opposite_ of what the
+	 * current D+/D- levels are e.g. if currently D+ high, D- low
+	 * (HS 'J'/Suspend), configure the mask to trigger on D+ low OR D- high
+	 */
+	intr_mask = DPSE_INTR_EN | DMSE_INTR_EN;
+	switch (qphy->mode) {
+	case PHY_MODE_USB_HOST_HS:
+	case PHY_MODE_USB_HOST_FS:
+	case PHY_MODE_USB_DEVICE_HS:
+	case PHY_MODE_USB_DEVICE_FS:
+		intr_mask |= DMSE_INTR_HIGH_SEL;
+		break;
+	case PHY_MODE_USB_HOST_LS:
+	case PHY_MODE_USB_DEVICE_LS:
+		intr_mask |= DPSE_INTR_HIGH_SEL;
+		break;
+	default:
+		/* No device connected, enable both DP/DM high interrupt */
+		intr_mask |= DMSE_INTR_HIGH_SEL;
+		intr_mask |= DPSE_INTR_HIGH_SEL;
+		break;
+	}
+
+	writel(intr_mask, qphy->base + cfg->regs[QUSB2PHY_INTR_CTRL]);
+
+	/* hold core PLL into reset */
+	if (cfg->has_pll_override) {
+		qusb2_setbits(qphy->base,
+			      cfg->regs[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE],
+			      CORE_PLL_EN_FROM_RESET | CORE_RESET |
+			      CORE_RESET_MUX);
+	}
+
+	/* enable phy auto-resume only if device is connected on bus */
+	if (qphy->mode != PHY_MODE_INVALID) {
+		qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TEST1],
+			      cfg->autoresume_en);
+		/* Autoresume bit has to be toggled in order to enable it */
+		qusb2_clrbits(qphy->base, cfg->regs[QUSB2PHY_PORT_TEST1],
+			      cfg->autoresume_en);
+	}
+
+	if (!qphy->has_se_clk_scheme)
+		clk_disable_unprepare(qphy->ref_clk);
+
+	clk_disable_unprepare(qphy->cfg_ahb_clk);
+	clk_disable_unprepare(qphy->iface_clk);
+
+	return 0;
+}
+
+static int __maybe_unused qusb2_phy_runtime_resume(struct device *dev)
+{
+	struct qusb2_phy *qphy = dev_get_drvdata(dev);
+	const struct qusb2_phy_cfg *cfg = qphy->cfg;
+	int ret;
+
+	dev_vdbg(dev, "Resuming QUSB2 phy, mode:%d\n", qphy->mode);
+
+	if (!qphy->phy_initialized) {
+		dev_vdbg(dev, "PHY not initialized, bailing out\n");
+		return 0;
+	}
+
+	ret = clk_prepare_enable(qphy->iface_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable iface_clk, %d\n", ret);
+		return ret;
+	}
+
+	ret = clk_prepare_enable(qphy->cfg_ahb_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable cfg ahb clock, %d\n", ret);
+		goto disable_iface_clk;
+	}
+
+	if (!qphy->has_se_clk_scheme) {
+		ret = clk_prepare_enable(qphy->ref_clk);
+		if (ret) {
+			dev_err(dev, "failed to enable ref clk, %d\n", ret);
+			goto disable_ahb_clk;
+		}
+	}
+
+	writel(0x0, qphy->base + cfg->regs[QUSB2PHY_INTR_CTRL]);
+
+	/* bring core PLL out of reset */
+	if (cfg->has_pll_override) {
+		qusb2_clrbits(qphy->base,
+			      cfg->regs[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE],
+			      CORE_RESET | CORE_RESET_MUX);
+	}
+
+	return 0;
+
+disable_ahb_clk:
+	clk_disable_unprepare(qphy->cfg_ahb_clk);
+disable_iface_clk:
+	clk_disable_unprepare(qphy->iface_clk);
+
+	return ret;
+}
+
+static int qusb2_phy_init(struct phy *phy)
+{
+	struct qusb2_phy *qphy = phy_get_drvdata(phy);
+	const struct qusb2_phy_cfg *cfg = qphy->cfg;
+	unsigned int val = 0;
+	unsigned int clk_scheme;
+	int ret;
+
+	dev_vdbg(&phy->dev, "%s(): Initializing QUSB2 phy\n", __func__);
+
+	/* turn on regulator supplies */
+	ret = regulator_bulk_enable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
+	if (ret)
+		return ret;
+
+	ret = clk_prepare_enable(qphy->iface_clk);
+	if (ret) {
+		dev_err(&phy->dev, "failed to enable iface_clk, %d\n", ret);
+		goto poweroff_phy;
+	}
+
+	/* enable ahb interface clock to program phy */
+	ret = clk_prepare_enable(qphy->cfg_ahb_clk);
+	if (ret) {
+		dev_err(&phy->dev, "failed to enable cfg ahb clock, %d\n", ret);
+		goto disable_iface_clk;
+	}
+
+	/* Perform phy reset */
+	ret = reset_control_assert(qphy->phy_reset);
+	if (ret) {
+		dev_err(&phy->dev, "failed to assert phy_reset, %d\n", ret);
+		goto disable_ahb_clk;
+	}
+
+	/* 100 us delay to keep PHY in reset mode */
+	usleep_range(100, 150);
+
+	ret = reset_control_deassert(qphy->phy_reset);
+	if (ret) {
+		dev_err(&phy->dev, "failed to de-assert phy_reset, %d\n", ret);
+		goto disable_ahb_clk;
+	}
+
+	/* Disable the PHY */
+	qusb2_setbits(qphy->base, cfg->regs[QUSB2PHY_PORT_POWERDOWN],
+		      qphy->cfg->disable_ctrl);
+
+	if (cfg->has_pll_test) {
+		/* save reset value to override reference clock scheme later */
+		val = readl(qphy->base + QUSB2PHY_PLL_TEST);
+	}
+
+	qcom_qusb2_phy_configure(qphy->base, cfg->regs, cfg->tbl,
+				 cfg->tbl_num);
+
+	/* Override board specific PHY tuning values */
+	qusb2_phy_override_phy_params(qphy);
+
+	/* Set efuse value for tuning the PHY */
+	qusb2_phy_set_tune2_param(qphy);
+
+	/* Enable the PHY */
+	qusb2_clrbits(qphy->base, cfg->regs[QUSB2PHY_PORT_POWERDOWN],
+		      POWER_DOWN);
+
+	/* Required to get phy pll lock successfully */
+	usleep_range(150, 160);
+
+	/* Default is single-ended clock on msm8996 */
+	qphy->has_se_clk_scheme = true;
+	/*
+	 * read TCSR_PHY_CLK_SCHEME register to check if single-ended
+	 * clock scheme is selected. If yes, then disable differential
+	 * ref_clk and use single-ended clock, otherwise use differential
+	 * ref_clk only.
+	 */
+	if (qphy->tcsr) {
+		ret = regmap_read(qphy->tcsr, qphy->cfg->clk_scheme_offset,
+				  &clk_scheme);
+		if (ret) {
+			dev_err(&phy->dev, "failed to read clk scheme reg\n");
+			goto assert_phy_reset;
+		}
+
+		/* is it a differential clock scheme ? */
+		if (!(clk_scheme & PHY_CLK_SCHEME_SEL)) {
+			dev_vdbg(&phy->dev, "%s(): select differential clk\n",
+				 __func__);
+			qphy->has_se_clk_scheme = false;
+		} else {
+			dev_vdbg(&phy->dev, "%s(): select single-ended clk\n",
+				 __func__);
+		}
+	}
+
+	if (!qphy->has_se_clk_scheme) {
+		ret = clk_prepare_enable(qphy->ref_clk);
+		if (ret) {
+			dev_err(&phy->dev, "failed to enable ref clk, %d\n",
+				ret);
+			goto assert_phy_reset;
+		}
+	}
+
+	if (cfg->has_pll_test) {
+		if (!qphy->has_se_clk_scheme)
+			val &= ~CLK_REF_SEL;
+		else
+			val |= CLK_REF_SEL;
+
+		writel(val, qphy->base + QUSB2PHY_PLL_TEST);
+
+		/* ensure above write is through */
+		readl(qphy->base + QUSB2PHY_PLL_TEST);
+	}
+
+	/* Required to get phy pll lock successfully */
+	usleep_range(100, 110);
+
+	val = readb(qphy->base + cfg->regs[QUSB2PHY_PLL_STATUS]);
+	if (!(val & cfg->mask_core_ready)) {
+		dev_err(&phy->dev,
+			"QUSB2PHY pll lock failed: status reg = %x\n", val);
+		ret = -EBUSY;
+		goto disable_ref_clk;
+	}
+	qphy->phy_initialized = true;
+
+	return 0;
+
+disable_ref_clk:
+	if (!qphy->has_se_clk_scheme)
+		clk_disable_unprepare(qphy->ref_clk);
+assert_phy_reset:
+	reset_control_assert(qphy->phy_reset);
+disable_ahb_clk:
+	clk_disable_unprepare(qphy->cfg_ahb_clk);
+disable_iface_clk:
+	clk_disable_unprepare(qphy->iface_clk);
+poweroff_phy:
+	regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
+
+	return ret;
+}
+
+static int qusb2_phy_exit(struct phy *phy)
+{
+	struct qusb2_phy *qphy = phy_get_drvdata(phy);
+
+	/* Disable the PHY */
+	qusb2_setbits(qphy->base, qphy->cfg->regs[QUSB2PHY_PORT_POWERDOWN],
+		      qphy->cfg->disable_ctrl);
+
+	if (!qphy->has_se_clk_scheme)
+		clk_disable_unprepare(qphy->ref_clk);
+
+	reset_control_assert(qphy->phy_reset);
+
+	clk_disable_unprepare(qphy->cfg_ahb_clk);
+	clk_disable_unprepare(qphy->iface_clk);
+
+	regulator_bulk_disable(ARRAY_SIZE(qphy->vregs), qphy->vregs);
+
+	qphy->phy_initialized = false;
+
+	return 0;
+}
+
+static const struct phy_ops qusb2_phy_gen_ops = {
+	.init		= qusb2_phy_init,
+	.exit		= qusb2_phy_exit,
+	.set_mode	= qusb2_phy_set_mode,
+	.owner		= THIS_MODULE,
+};
+
+static const struct of_device_id qusb2_phy_of_match_table[] = {
+	{
+		.compatible	= "qcom,msm8996-qusb2-phy",
+		.data		= &msm8996_phy_cfg,
+	}, {
+		.compatible	= "qcom,sdm845-qusb2-phy",
+		.data		= &sdm845_phy_cfg,
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, qusb2_phy_of_match_table);
+
+static const struct dev_pm_ops qusb2_phy_pm_ops = {
+	SET_RUNTIME_PM_OPS(qusb2_phy_runtime_suspend,
+			   qusb2_phy_runtime_resume, NULL)
+};
+
+static int qusb2_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct qusb2_phy *qphy;
+	struct phy_provider *phy_provider;
+	struct phy *generic_phy;
+	struct resource *res;
+	int ret, i;
+	int num;
+	u32 value;
+
+	qphy = devm_kzalloc(dev, sizeof(*qphy), GFP_KERNEL);
+	if (!qphy)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	qphy->base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(qphy->base))
+		return PTR_ERR(qphy->base);
+
+	qphy->cfg_ahb_clk = devm_clk_get(dev, "cfg_ahb");
+	if (IS_ERR(qphy->cfg_ahb_clk)) {
+		ret = PTR_ERR(qphy->cfg_ahb_clk);
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "failed to get cfg ahb clk, %d\n", ret);
+		return ret;
+	}
+
+	qphy->ref_clk = devm_clk_get(dev, "ref");
+	if (IS_ERR(qphy->ref_clk)) {
+		ret = PTR_ERR(qphy->ref_clk);
+		if (ret != -EPROBE_DEFER)
+			dev_err(dev, "failed to get ref clk, %d\n", ret);
+		return ret;
+	}
+
+	qphy->iface_clk = devm_clk_get(dev, "iface");
+	if (IS_ERR(qphy->iface_clk)) {
+		ret = PTR_ERR(qphy->iface_clk);
+		if (ret == -EPROBE_DEFER)
+			return ret;
+		qphy->iface_clk = NULL;
+		dev_dbg(dev, "failed to get iface clk, %d\n", ret);
+	}
+
+	qphy->phy_reset = devm_reset_control_get_by_index(&pdev->dev, 0);
+	if (IS_ERR(qphy->phy_reset)) {
+		dev_err(dev, "failed to get phy core reset\n");
+		return PTR_ERR(qphy->phy_reset);
+	}
+
+	num = ARRAY_SIZE(qphy->vregs);
+	for (i = 0; i < num; i++)
+		qphy->vregs[i].supply = qusb2_phy_vreg_names[i];
+
+	ret = devm_regulator_bulk_get(dev, num, qphy->vregs);
+	if (ret) {
+		dev_err(dev, "failed to get regulator supplies\n");
+		return ret;
+	}
+
+	/* Get the specific init parameters of QMP phy */
+	qphy->cfg = of_device_get_match_data(dev);
+
+	qphy->tcsr = syscon_regmap_lookup_by_phandle(dev->of_node,
+							"qcom,tcsr-syscon");
+	if (IS_ERR(qphy->tcsr)) {
+		dev_dbg(dev, "failed to lookup TCSR regmap\n");
+		qphy->tcsr = NULL;
+	}
+
+	qphy->cell = devm_nvmem_cell_get(dev, NULL);
+	if (IS_ERR(qphy->cell)) {
+		if (PTR_ERR(qphy->cell) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+		qphy->cell = NULL;
+		dev_dbg(dev, "failed to lookup tune2 hstx trim value\n");
+	}
+
+	if (!of_property_read_u32(dev->of_node, "qcom,imp-res-offset-value",
+				  &value)) {
+		qphy->imp_res_offset_value = (u8)value;
+		qphy->override_imp_res_offset = true;
+	}
+
+	if (!of_property_read_u32(dev->of_node, "qcom,hstx-trim-value",
+				  &value)) {
+		qphy->hstx_trim_value = (u8)value;
+		qphy->override_hstx_trim = true;
+	}
+
+	if (!of_property_read_u32(dev->of_node, "qcom,preemphasis-level",
+				     &value)) {
+		qphy->preemphasis_level = (u8)value;
+		qphy->override_preemphasis = true;
+	}
+
+	if (!of_property_read_u32(dev->of_node, "qcom,preemphasis-width",
+				     &value)) {
+		qphy->preemphasis_width = (u8)value;
+		qphy->override_preemphasis_width = true;
+	}
+
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+	/*
+	 * Prevent runtime pm from being ON by default. Users can enable
+	 * it using power/control in sysfs.
+	 */
+	pm_runtime_forbid(dev);
+
+	generic_phy = devm_phy_create(dev, NULL, &qusb2_phy_gen_ops);
+	if (IS_ERR(generic_phy)) {
+		ret = PTR_ERR(generic_phy);
+		dev_err(dev, "failed to create phy, %d\n", ret);
+		pm_runtime_disable(dev);
+		return ret;
+	}
+	qphy->phy = generic_phy;
+
+	dev_set_drvdata(dev, qphy);
+	phy_set_drvdata(generic_phy, qphy);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+	if (!IS_ERR(phy_provider))
+		dev_info(dev, "Registered Qcom-QUSB2 phy\n");
+	else
+		pm_runtime_disable(dev);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver qusb2_phy_driver = {
+	.probe		= qusb2_phy_probe,
+	.driver = {
+		.name	= "qcom-qusb2-phy",
+		.pm	= &qusb2_phy_pm_ops,
+		.of_match_table = qusb2_phy_of_match_table,
+	},
+};
+
+module_platform_driver(qusb2_phy_driver);
+
+MODULE_AUTHOR("Vivek Gautam <vivek.gautam@codeaurora.org>");
+MODULE_DESCRIPTION("Qualcomm QUSB2 PHY driver");
+MODULE_LICENSE("GPL v2");