diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/tty/isicom.c | 1722 |
1 files changed, 1722 insertions, 0 deletions
diff --git a/drivers/tty/isicom.c b/drivers/tty/isicom.c new file mode 100644 index 000000000..8d96e8696 --- /dev/null +++ b/drivers/tty/isicom.c @@ -0,0 +1,1722 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Original driver code supplied by Multi-Tech + * + * Changes + * 1/9/98 alan@lxorguk.ukuu.org.uk + * Merge to 2.0.x kernel tree + * Obtain and use official major/minors + * Loader switched to a misc device + * (fixed range check bug as a side effect) + * Printk clean up + * 9/12/98 alan@lxorguk.ukuu.org.uk + * Rough port to 2.1.x + * + * 10/6/99 sameer Merged the ISA and PCI drivers to + * a new unified driver. + * + * 3/9/99 sameer Added support for ISI4616 cards. + * + * 16/9/99 sameer We do not force RTS low anymore. + * This is to prevent the firmware + * from getting confused. + * + * 26/10/99 sameer Cosmetic changes:The driver now + * dumps the Port Count information + * along with I/O address and IRQ. + * + * 13/12/99 sameer Fixed the problem with IRQ sharing. + * + * 10/5/00 sameer Fixed isicom_shutdown_board() + * to not lower DTR on all the ports + * when the last port on the card is + * closed. + * + * 10/5/00 sameer Signal mask setup command added + * to isicom_setup_port and + * isicom_shutdown_port. + * + * 24/5/00 sameer The driver is now SMP aware. + * + * + * 27/11/00 Vinayak P Risbud Fixed the Driver Crash Problem + * + * + * 03/01/01 anil .s Added support for resetting the + * internal modems on ISI cards. + * + * 08/02/01 anil .s Upgraded the driver for kernel + * 2.4.x + * + * 11/04/01 Kevin Fixed firmware load problem with + * ISIHP-4X card + * + * 30/04/01 anil .s Fixed the remote login through + * ISI port problem. Now the link + * does not go down before password + * prompt. + * + * 03/05/01 anil .s Fixed the problem with IRQ sharing + * among ISI-PCI cards. + * + * 03/05/01 anil .s Added support to display the version + * info during insmod as well as module + * listing by lsmod. + * + * 10/05/01 anil .s Done the modifications to the source + * file and Install script so that the + * same installation can be used for + * 2.2.x and 2.4.x kernel. + * + * 06/06/01 anil .s Now we drop both dtr and rts during + * shutdown_port as well as raise them + * during isicom_config_port. + * + * 09/06/01 acme@conectiva.com.br use capable, not suser, do + * restore_flags on failure in + * isicom_send_break, verify put_user + * result + * + * 11/02/03 ranjeeth Added support for 230 Kbps and 460 Kbps + * Baud index extended to 21 + * + * 20/03/03 ranjeeth Made to work for Linux Advanced server. + * Taken care of license warning. + * + * 10/12/03 Ravindra Made to work for Fedora Core 1 of + * Red Hat Distribution + * + * 06/01/05 Alan Cox Merged the ISI and base kernel strands + * into a single 2.6 driver + * + * *********************************************************** + * + * To use this driver you also need the support package. You + * can find this in RPM format on + * ftp://ftp.linux.org.uk/pub/linux/alan + * + * You can find the original tools for this direct from Multitech + * ftp://ftp.multitech.com/ISI-Cards/ + * + * Having installed the cards the module options (/etc/modprobe.d/) + * + * options isicom io=card1,card2,card3,card4 irq=card1,card2,card3,card4 + * + * Omit those entries for boards you don't have installed. + * + * TODO + * Merge testing + * 64-bit verification + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/module.h> +#include <linux/firmware.h> +#include <linux/kernel.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/termios.h> +#include <linux/fs.h> +#include <linux/sched.h> +#include <linux/serial.h> +#include <linux/mm.h> +#include <linux/interrupt.h> +#include <linux/timer.h> +#include <linux/delay.h> +#include <linux/ioport.h> +#include <linux/slab.h> + +#include <linux/uaccess.h> +#include <linux/io.h> + +#include <linux/pci.h> + +#include <linux/isicom.h> + +#define InterruptTheCard(base) outw(0, (base) + 0xc) +#define ClearInterrupt(base) inw((base) + 0x0a) + +#ifdef DEBUG +#define isicom_paranoia_check(a, b, c) __isicom_paranoia_check((a), (b), (c)) +#else +#define isicom_paranoia_check(a, b, c) 0 +#endif + +static int isicom_probe(struct pci_dev *, const struct pci_device_id *); +static void isicom_remove(struct pci_dev *); + +static const struct pci_device_id isicom_pci_tbl[] = { + { PCI_DEVICE(VENDOR_ID, 0x2028) }, + { PCI_DEVICE(VENDOR_ID, 0x2051) }, + { PCI_DEVICE(VENDOR_ID, 0x2052) }, + { PCI_DEVICE(VENDOR_ID, 0x2053) }, + { PCI_DEVICE(VENDOR_ID, 0x2054) }, + { PCI_DEVICE(VENDOR_ID, 0x2055) }, + { PCI_DEVICE(VENDOR_ID, 0x2056) }, + { PCI_DEVICE(VENDOR_ID, 0x2057) }, + { PCI_DEVICE(VENDOR_ID, 0x2058) }, + { 0 } +}; +MODULE_DEVICE_TABLE(pci, isicom_pci_tbl); + +static struct pci_driver isicom_driver = { + .name = "isicom", + .id_table = isicom_pci_tbl, + .probe = isicom_probe, + .remove = isicom_remove +}; + +static int prev_card = 3; /* start servicing isi_card[0] */ +static struct tty_driver *isicom_normal; + +static void isicom_tx(struct timer_list *unused); +static void isicom_start(struct tty_struct *tty); + +static DEFINE_TIMER(tx, isicom_tx); + +/* baud index mappings from linux defns to isi */ + +static signed char linuxb_to_isib[] = { + -1, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 16, 17, 18, 19, 20, 21 +}; + +struct isi_board { + unsigned long base; + int irq; + unsigned char port_count; + unsigned short status; + unsigned short port_status; /* each bit for each port */ + unsigned short shift_count; + struct isi_port *ports; + signed char count; + spinlock_t card_lock; /* Card wide lock 11/5/00 -sameer */ + unsigned long flags; + unsigned int index; +}; + +struct isi_port { + unsigned short magic; + struct tty_port port; + u16 channel; + u16 status; + struct isi_board *card; + unsigned char *xmit_buf; + int xmit_head; + int xmit_tail; + int xmit_cnt; +}; + +static struct isi_board isi_card[BOARD_COUNT]; +static struct isi_port isi_ports[PORT_COUNT]; + +/* + * Locking functions for card level locking. We need to own both + * the kernel lock for the card and have the card in a position that + * it wants to talk. + */ + +static int WaitTillCardIsFree(unsigned long base) +{ + unsigned int count = 0; + + while (!(inw(base + 0xe) & 0x1) && count++ < 100) + mdelay(1); + + return !(inw(base + 0xe) & 0x1); +} + +static int lock_card(struct isi_board *card) +{ + unsigned long base = card->base; + unsigned int retries, a; + + for (retries = 0; retries < 10; retries++) { + spin_lock_irqsave(&card->card_lock, card->flags); + for (a = 0; a < 10; a++) { + if (inw(base + 0xe) & 0x1) + return 1; + udelay(10); + } + spin_unlock_irqrestore(&card->card_lock, card->flags); + msleep(10); + } + pr_warn("Failed to lock Card (0x%lx)\n", card->base); + + return 0; /* Failed to acquire the card! */ +} + +static void unlock_card(struct isi_board *card) +{ + spin_unlock_irqrestore(&card->card_lock, card->flags); +} + +/* + * ISI Card specific ops ... + */ + +/* card->lock HAS to be held */ +static void raise_dtr(struct isi_port *port) +{ + struct isi_board *card = port->card; + unsigned long base = card->base; + u16 channel = port->channel; + + if (WaitTillCardIsFree(base)) + return; + + outw(0x8000 | (channel << card->shift_count) | 0x02, base); + outw(0x0504, base); + InterruptTheCard(base); + port->status |= ISI_DTR; +} + +/* card->lock HAS to be held */ +static void drop_dtr(struct isi_port *port) +{ + struct isi_board *card = port->card; + unsigned long base = card->base; + u16 channel = port->channel; + + if (WaitTillCardIsFree(base)) + return; + + outw(0x8000 | (channel << card->shift_count) | 0x02, base); + outw(0x0404, base); + InterruptTheCard(base); + port->status &= ~ISI_DTR; +} + +/* card->lock HAS to be held */ +static inline void raise_rts(struct isi_port *port) +{ + struct isi_board *card = port->card; + unsigned long base = card->base; + u16 channel = port->channel; + + if (WaitTillCardIsFree(base)) + return; + + outw(0x8000 | (channel << card->shift_count) | 0x02, base); + outw(0x0a04, base); + InterruptTheCard(base); + port->status |= ISI_RTS; +} + +/* card->lock HAS to be held */ +static inline void drop_rts(struct isi_port *port) +{ + struct isi_board *card = port->card; + unsigned long base = card->base; + u16 channel = port->channel; + + if (WaitTillCardIsFree(base)) + return; + + outw(0x8000 | (channel << card->shift_count) | 0x02, base); + outw(0x0804, base); + InterruptTheCard(base); + port->status &= ~ISI_RTS; +} + +/* card->lock MUST NOT be held */ + +static void isicom_dtr_rts(struct tty_port *port, int on) +{ + struct isi_port *ip = container_of(port, struct isi_port, port); + struct isi_board *card = ip->card; + unsigned long base = card->base; + u16 channel = ip->channel; + + if (!lock_card(card)) + return; + + if (on) { + outw(0x8000 | (channel << card->shift_count) | 0x02, base); + outw(0x0f04, base); + InterruptTheCard(base); + ip->status |= (ISI_DTR | ISI_RTS); + } else { + outw(0x8000 | (channel << card->shift_count) | 0x02, base); + outw(0x0C04, base); + InterruptTheCard(base); + ip->status &= ~(ISI_DTR | ISI_RTS); + } + unlock_card(card); +} + +/* card->lock HAS to be held */ +static void drop_dtr_rts(struct isi_port *port) +{ + struct isi_board *card = port->card; + unsigned long base = card->base; + u16 channel = port->channel; + + if (WaitTillCardIsFree(base)) + return; + + outw(0x8000 | (channel << card->shift_count) | 0x02, base); + outw(0x0c04, base); + InterruptTheCard(base); + port->status &= ~(ISI_RTS | ISI_DTR); +} + +/* + * ISICOM Driver specific routines ... + * + */ + +static inline int __isicom_paranoia_check(struct isi_port const *port, + char *name, const char *routine) +{ + if (!port) { + pr_warn("Warning: bad isicom magic for dev %s in %s\n", + name, routine); + return 1; + } + if (port->magic != ISICOM_MAGIC) { + pr_warn("Warning: NULL isicom port for dev %s in %s\n", + name, routine); + return 1; + } + + return 0; +} + +/* + * Transmitter. + * + * We shovel data into the card buffers on a regular basis. The card + * will do the rest of the work for us. + */ + +static void isicom_tx(struct timer_list *unused) +{ + unsigned long flags, base; + unsigned int retries; + short count = (BOARD_COUNT-1), card; + short txcount, wrd, residue, word_count, cnt; + struct isi_port *port; + struct tty_struct *tty; + + /* find next active board */ + card = (prev_card + 1) & 0x0003; + while (count-- > 0) { + if (isi_card[card].status & BOARD_ACTIVE) + break; + card = (card + 1) & 0x0003; + } + if (!(isi_card[card].status & BOARD_ACTIVE)) + goto sched_again; + + prev_card = card; + + count = isi_card[card].port_count; + port = isi_card[card].ports; + base = isi_card[card].base; + + spin_lock_irqsave(&isi_card[card].card_lock, flags); + for (retries = 0; retries < 100; retries++) { + if (inw(base + 0xe) & 0x1) + break; + udelay(2); + } + if (retries >= 100) + goto unlock; + + tty = tty_port_tty_get(&port->port); + if (tty == NULL) + goto put_unlock; + + for (; count > 0; count--, port++) { + /* port not active or tx disabled to force flow control */ + if (!tty_port_initialized(&port->port) || + !(port->status & ISI_TXOK)) + continue; + + txcount = min_t(short, TX_SIZE, port->xmit_cnt); + if (txcount <= 0 || tty->stopped || tty->hw_stopped) + continue; + + if (!(inw(base + 0x02) & (1 << port->channel))) + continue; + + pr_debug("txing %d bytes, port%d.\n", + txcount, port->channel + 1); + outw((port->channel << isi_card[card].shift_count) | txcount, + base); + residue = NO; + wrd = 0; + while (1) { + cnt = min_t(int, txcount, (SERIAL_XMIT_SIZE + - port->xmit_tail)); + if (residue == YES) { + residue = NO; + if (cnt > 0) { + wrd |= (port->port.xmit_buf[port->xmit_tail] + << 8); + port->xmit_tail = (port->xmit_tail + 1) + & (SERIAL_XMIT_SIZE - 1); + port->xmit_cnt--; + txcount--; + cnt--; + outw(wrd, base); + } else { + outw(wrd, base); + break; + } + } + if (cnt <= 0) + break; + word_count = cnt >> 1; + outsw(base, port->port.xmit_buf+port->xmit_tail, word_count); + port->xmit_tail = (port->xmit_tail + + (word_count << 1)) & (SERIAL_XMIT_SIZE - 1); + txcount -= (word_count << 1); + port->xmit_cnt -= (word_count << 1); + if (cnt & 0x0001) { + residue = YES; + wrd = port->port.xmit_buf[port->xmit_tail]; + port->xmit_tail = (port->xmit_tail + 1) + & (SERIAL_XMIT_SIZE - 1); + port->xmit_cnt--; + txcount--; + } + } + + InterruptTheCard(base); + if (port->xmit_cnt <= 0) + port->status &= ~ISI_TXOK; + if (port->xmit_cnt <= WAKEUP_CHARS) + tty_wakeup(tty); + } + +put_unlock: + tty_kref_put(tty); +unlock: + spin_unlock_irqrestore(&isi_card[card].card_lock, flags); + /* schedule another tx for hopefully in about 10ms */ +sched_again: + mod_timer(&tx, jiffies + msecs_to_jiffies(10)); +} + +/* + * Main interrupt handler routine + */ + +static irqreturn_t isicom_interrupt(int irq, void *dev_id) +{ + struct isi_board *card = dev_id; + struct isi_port *port; + struct tty_struct *tty; + unsigned long base; + u16 header, word_count, count, channel; + short byte_count; + unsigned char *rp; + + if (!card || !(card->status & FIRMWARE_LOADED)) + return IRQ_NONE; + + base = card->base; + + /* did the card interrupt us? */ + if (!(inw(base + 0x0e) & 0x02)) + return IRQ_NONE; + + spin_lock(&card->card_lock); + + /* + * disable any interrupts from the PCI card and lower the + * interrupt line + */ + outw(0x8000, base+0x04); + ClearInterrupt(base); + + inw(base); /* get the dummy word out */ + header = inw(base); + channel = (header & 0x7800) >> card->shift_count; + byte_count = header & 0xff; + + if (channel + 1 > card->port_count) { + pr_warn("%s(0x%lx): %d(channel) > port_count\n", + __func__, base, channel + 1); + outw(0x0000, base+0x04); /* enable interrupts */ + spin_unlock(&card->card_lock); + return IRQ_HANDLED; + } + port = card->ports + channel; + if (!tty_port_initialized(&port->port)) { + outw(0x0000, base+0x04); /* enable interrupts */ + spin_unlock(&card->card_lock); + return IRQ_HANDLED; + } + + tty = tty_port_tty_get(&port->port); + if (tty == NULL) { + word_count = byte_count >> 1; + while (byte_count > 1) { + inw(base); + byte_count -= 2; + } + if (byte_count & 0x01) + inw(base); + outw(0x0000, base+0x04); /* enable interrupts */ + spin_unlock(&card->card_lock); + return IRQ_HANDLED; + } + + if (header & 0x8000) { /* Status Packet */ + header = inw(base); + switch (header & 0xff) { + case 0: /* Change in EIA signals */ + if (tty_port_check_carrier(&port->port)) { + if (port->status & ISI_DCD) { + if (!(header & ISI_DCD)) { + /* Carrier has been lost */ + pr_debug("%s: DCD->low.\n", + __func__); + port->status &= ~ISI_DCD; + tty_hangup(tty); + } + } else if (header & ISI_DCD) { + /* Carrier has been detected */ + pr_debug("%s: DCD->high.\n", + __func__); + port->status |= ISI_DCD; + wake_up_interruptible(&port->port.open_wait); + } + } else { + if (header & ISI_DCD) + port->status |= ISI_DCD; + else + port->status &= ~ISI_DCD; + } + + if (tty_port_cts_enabled(&port->port)) { + if (tty->hw_stopped) { + if (header & ISI_CTS) { + tty->hw_stopped = 0; + /* start tx ing */ + port->status |= (ISI_TXOK + | ISI_CTS); + tty_wakeup(tty); + } + } else if (!(header & ISI_CTS)) { + tty->hw_stopped = 1; + /* stop tx ing */ + port->status &= ~(ISI_TXOK | ISI_CTS); + } + } else { + if (header & ISI_CTS) + port->status |= ISI_CTS; + else + port->status &= ~ISI_CTS; + } + + if (header & ISI_DSR) + port->status |= ISI_DSR; + else + port->status &= ~ISI_DSR; + + if (header & ISI_RI) + port->status |= ISI_RI; + else + port->status &= ~ISI_RI; + + break; + + case 1: /* Received Break !!! */ + tty_insert_flip_char(&port->port, 0, TTY_BREAK); + if (port->port.flags & ASYNC_SAK) + do_SAK(tty); + tty_flip_buffer_push(&port->port); + break; + + case 2: /* Statistics */ + pr_debug("%s: stats!!!\n", __func__); + break; + + default: + pr_debug("%s: Unknown code in status packet.\n", + __func__); + break; + } + } else { /* Data Packet */ + count = tty_prepare_flip_string(&port->port, &rp, + byte_count & ~1); + pr_debug("%s: Can rx %d of %d bytes.\n", + __func__, count, byte_count); + word_count = count >> 1; + insw(base, rp, word_count); + byte_count -= (word_count << 1); + if (count & 0x0001) { + tty_insert_flip_char(&port->port, inw(base) & 0xff, + TTY_NORMAL); + byte_count -= 2; + } + if (byte_count > 0) { + pr_debug("%s(0x%lx:%d): Flip buffer overflow! dropping bytes...\n", + __func__, base, channel + 1); + /* drain out unread xtra data */ + while (byte_count > 0) { + inw(base); + byte_count -= 2; + } + } + tty_flip_buffer_push(&port->port); + } + outw(0x0000, base+0x04); /* enable interrupts */ + spin_unlock(&card->card_lock); + tty_kref_put(tty); + + return IRQ_HANDLED; +} + +static void isicom_config_port(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + struct isi_board *card = port->card; + unsigned long baud; + unsigned long base = card->base; + u16 channel_setup, channel = port->channel, + shift_count = card->shift_count; + unsigned char flow_ctrl; + + /* FIXME: Switch to new tty baud API */ + baud = C_BAUD(tty); + if (baud & CBAUDEX) { + baud &= ~CBAUDEX; + + /* if CBAUDEX bit is on and the baud is set to either 50 or 75 + * then the card is programmed for 57.6Kbps or 115Kbps + * respectively. + */ + + /* 1,2,3,4 => 57.6, 115.2, 230, 460 kbps resp. */ + if (baud < 1 || baud > 4) + tty->termios.c_cflag &= ~CBAUDEX; + else + baud += 15; + } + if (baud == 15) { + + /* the ASYNC_SPD_HI and ASYNC_SPD_VHI options are set + * by the set_serial_info ioctl ... this is done by + * the 'setserial' utility. + */ + + if ((port->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_HI) + baud++; /* 57.6 Kbps */ + if ((port->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_VHI) + baud += 2; /* 115 Kbps */ + if ((port->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_SHI) + baud += 3; /* 230 kbps*/ + if ((port->port.flags & ASYNC_SPD_MASK) == ASYNC_SPD_WARP) + baud += 4; /* 460 kbps*/ + } + if (linuxb_to_isib[baud] == -1) { + /* hang up */ + drop_dtr(port); + return; + } else + raise_dtr(port); + + if (WaitTillCardIsFree(base) == 0) { + outw(0x8000 | (channel << shift_count) | 0x03, base); + outw(linuxb_to_isib[baud] << 8 | 0x03, base); + channel_setup = 0; + switch (C_CSIZE(tty)) { + case CS5: + channel_setup |= ISICOM_CS5; + break; + case CS6: + channel_setup |= ISICOM_CS6; + break; + case CS7: + channel_setup |= ISICOM_CS7; + break; + case CS8: + channel_setup |= ISICOM_CS8; + break; + } + + if (C_CSTOPB(tty)) + channel_setup |= ISICOM_2SB; + if (C_PARENB(tty)) { + channel_setup |= ISICOM_EVPAR; + if (C_PARODD(tty)) + channel_setup |= ISICOM_ODPAR; + } + outw(channel_setup, base); + InterruptTheCard(base); + } + tty_port_set_check_carrier(&port->port, !C_CLOCAL(tty)); + + /* flow control settings ...*/ + flow_ctrl = 0; + tty_port_set_cts_flow(&port->port, C_CRTSCTS(tty)); + if (C_CRTSCTS(tty)) + flow_ctrl |= ISICOM_CTSRTS; + if (I_IXON(tty)) + flow_ctrl |= ISICOM_RESPOND_XONXOFF; + if (I_IXOFF(tty)) + flow_ctrl |= ISICOM_INITIATE_XONXOFF; + + if (WaitTillCardIsFree(base) == 0) { + outw(0x8000 | (channel << shift_count) | 0x04, base); + outw(flow_ctrl << 8 | 0x05, base); + outw((STOP_CHAR(tty)) << 8 | (START_CHAR(tty)), base); + InterruptTheCard(base); + } + + /* rx enabled -> enable port for rx on the card */ + if (C_CREAD(tty)) { + card->port_status |= (1 << channel); + outw(card->port_status, base + 0x02); + } +} + +/* open et all */ + +static inline void isicom_setup_board(struct isi_board *bp) +{ + int channel; + struct isi_port *port; + + bp->count++; + if (!(bp->status & BOARD_INIT)) { + port = bp->ports; + for (channel = 0; channel < bp->port_count; channel++, port++) + drop_dtr_rts(port); + } + bp->status |= BOARD_ACTIVE | BOARD_INIT; +} + +/* Activate and thus setup board are protected from races against shutdown + by the tty_port mutex */ + +static int isicom_activate(struct tty_port *tport, struct tty_struct *tty) +{ + struct isi_port *port = container_of(tport, struct isi_port, port); + struct isi_board *card = port->card; + unsigned long flags; + + if (tty_port_alloc_xmit_buf(tport) < 0) + return -ENOMEM; + + spin_lock_irqsave(&card->card_lock, flags); + isicom_setup_board(card); + + port->xmit_cnt = port->xmit_head = port->xmit_tail = 0; + + /* discard any residual data */ + if (WaitTillCardIsFree(card->base) == 0) { + outw(0x8000 | (port->channel << card->shift_count) | 0x02, + card->base); + outw(((ISICOM_KILLTX | ISICOM_KILLRX) << 8) | 0x06, card->base); + InterruptTheCard(card->base); + } + isicom_config_port(tty); + spin_unlock_irqrestore(&card->card_lock, flags); + + return 0; +} + +static int isicom_carrier_raised(struct tty_port *port) +{ + struct isi_port *ip = container_of(port, struct isi_port, port); + return (ip->status & ISI_DCD)?1 : 0; +} + +static struct tty_port *isicom_find_port(struct tty_struct *tty) +{ + struct isi_port *port; + struct isi_board *card; + unsigned int board; + int line = tty->index; + + board = BOARD(line); + card = &isi_card[board]; + + if (!(card->status & FIRMWARE_LOADED)) + return NULL; + + /* open on a port greater than the port count for the card !!! */ + if (line > ((board * 16) + card->port_count - 1)) + return NULL; + + port = &isi_ports[line]; + if (isicom_paranoia_check(port, tty->name, "isicom_open")) + return NULL; + + return &port->port; +} + +static int isicom_open(struct tty_struct *tty, struct file *filp) +{ + struct isi_port *port; + struct tty_port *tport; + + tport = isicom_find_port(tty); + if (tport == NULL) + return -ENODEV; + port = container_of(tport, struct isi_port, port); + + tty->driver_data = port; + return tty_port_open(tport, tty, filp); +} + +/* close et all */ + +/* card->lock HAS to be held */ +static void isicom_shutdown_port(struct isi_port *port) +{ + struct isi_board *card = port->card; + + if (--card->count < 0) { + pr_debug("%s: bad board(0x%lx) count %d.\n", + __func__, card->base, card->count); + card->count = 0; + } + /* last port was closed, shutdown that board too */ + if (!card->count) + card->status &= BOARD_ACTIVE; +} + +static void isicom_flush_buffer(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + struct isi_board *card = port->card; + unsigned long flags; + + if (isicom_paranoia_check(port, tty->name, "isicom_flush_buffer")) + return; + + spin_lock_irqsave(&card->card_lock, flags); + port->xmit_cnt = port->xmit_head = port->xmit_tail = 0; + spin_unlock_irqrestore(&card->card_lock, flags); + + tty_wakeup(tty); +} + +static void isicom_shutdown(struct tty_port *port) +{ + struct isi_port *ip = container_of(port, struct isi_port, port); + struct isi_board *card = ip->card; + unsigned long flags; + + /* indicate to the card that no more data can be received + on this port */ + spin_lock_irqsave(&card->card_lock, flags); + card->port_status &= ~(1 << ip->channel); + outw(card->port_status, card->base + 0x02); + isicom_shutdown_port(ip); + spin_unlock_irqrestore(&card->card_lock, flags); + tty_port_free_xmit_buf(port); +} + +static void isicom_close(struct tty_struct *tty, struct file *filp) +{ + struct isi_port *ip = tty->driver_data; + struct tty_port *port; + + if (ip == NULL) + return; + + port = &ip->port; + if (isicom_paranoia_check(ip, tty->name, "isicom_close")) + return; + tty_port_close(port, tty, filp); +} + +/* write et all */ +static int isicom_write(struct tty_struct *tty, const unsigned char *buf, + int count) +{ + struct isi_port *port = tty->driver_data; + struct isi_board *card = port->card; + unsigned long flags; + int cnt, total = 0; + + if (isicom_paranoia_check(port, tty->name, "isicom_write")) + return 0; + + spin_lock_irqsave(&card->card_lock, flags); + + while (1) { + cnt = min_t(int, count, min(SERIAL_XMIT_SIZE - port->xmit_cnt + - 1, SERIAL_XMIT_SIZE - port->xmit_head)); + if (cnt <= 0) + break; + + memcpy(port->port.xmit_buf + port->xmit_head, buf, cnt); + port->xmit_head = (port->xmit_head + cnt) & (SERIAL_XMIT_SIZE + - 1); + port->xmit_cnt += cnt; + buf += cnt; + count -= cnt; + total += cnt; + } + if (port->xmit_cnt && !tty->stopped && !tty->hw_stopped) + port->status |= ISI_TXOK; + spin_unlock_irqrestore(&card->card_lock, flags); + return total; +} + +/* put_char et all */ +static int isicom_put_char(struct tty_struct *tty, unsigned char ch) +{ + struct isi_port *port = tty->driver_data; + struct isi_board *card = port->card; + unsigned long flags; + + if (isicom_paranoia_check(port, tty->name, "isicom_put_char")) + return 0; + + spin_lock_irqsave(&card->card_lock, flags); + if (port->xmit_cnt >= SERIAL_XMIT_SIZE - 1) { + spin_unlock_irqrestore(&card->card_lock, flags); + return 0; + } + + port->port.xmit_buf[port->xmit_head++] = ch; + port->xmit_head &= (SERIAL_XMIT_SIZE - 1); + port->xmit_cnt++; + spin_unlock_irqrestore(&card->card_lock, flags); + return 1; +} + +/* flush_chars et all */ +static void isicom_flush_chars(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + + if (isicom_paranoia_check(port, tty->name, "isicom_flush_chars")) + return; + + if (port->xmit_cnt <= 0 || tty->stopped || tty->hw_stopped || + !port->port.xmit_buf) + return; + + /* this tells the transmitter to consider this port for + data output to the card ... that's the best we can do. */ + port->status |= ISI_TXOK; +} + +/* write_room et all */ +static int isicom_write_room(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + int free; + + if (isicom_paranoia_check(port, tty->name, "isicom_write_room")) + return 0; + + free = SERIAL_XMIT_SIZE - port->xmit_cnt - 1; + if (free < 0) + free = 0; + return free; +} + +/* chars_in_buffer et all */ +static int isicom_chars_in_buffer(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + if (isicom_paranoia_check(port, tty->name, "isicom_chars_in_buffer")) + return 0; + return port->xmit_cnt; +} + +/* ioctl et all */ +static int isicom_send_break(struct tty_struct *tty, int length) +{ + struct isi_port *port = tty->driver_data; + struct isi_board *card = port->card; + unsigned long base = card->base; + + if (length == -1) + return -EOPNOTSUPP; + + if (!lock_card(card)) + return -EINVAL; + + outw(0x8000 | ((port->channel) << (card->shift_count)) | 0x3, base); + outw((length & 0xff) << 8 | 0x00, base); + outw((length & 0xff00u), base); + InterruptTheCard(base); + + unlock_card(card); + return 0; +} + +static int isicom_tiocmget(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + /* just send the port status */ + u16 status = port->status; + + if (isicom_paranoia_check(port, tty->name, "isicom_ioctl")) + return -ENODEV; + + return ((status & ISI_RTS) ? TIOCM_RTS : 0) | + ((status & ISI_DTR) ? TIOCM_DTR : 0) | + ((status & ISI_DCD) ? TIOCM_CAR : 0) | + ((status & ISI_DSR) ? TIOCM_DSR : 0) | + ((status & ISI_CTS) ? TIOCM_CTS : 0) | + ((status & ISI_RI ) ? TIOCM_RI : 0); +} + +static int isicom_tiocmset(struct tty_struct *tty, + unsigned int set, unsigned int clear) +{ + struct isi_port *port = tty->driver_data; + unsigned long flags; + + if (isicom_paranoia_check(port, tty->name, "isicom_ioctl")) + return -ENODEV; + + spin_lock_irqsave(&port->card->card_lock, flags); + if (set & TIOCM_RTS) + raise_rts(port); + if (set & TIOCM_DTR) + raise_dtr(port); + + if (clear & TIOCM_RTS) + drop_rts(port); + if (clear & TIOCM_DTR) + drop_dtr(port); + spin_unlock_irqrestore(&port->card->card_lock, flags); + + return 0; +} + +static int isicom_set_serial_info(struct tty_struct *tty, + struct serial_struct __user *info) +{ + struct isi_port *port = tty->driver_data; + struct serial_struct newinfo; + int reconfig_port; + + if (copy_from_user(&newinfo, info, sizeof(newinfo))) + return -EFAULT; + + mutex_lock(&port->port.mutex); + reconfig_port = ((port->port.flags & ASYNC_SPD_MASK) != + (newinfo.flags & ASYNC_SPD_MASK)); + + if (!capable(CAP_SYS_ADMIN)) { + if ((newinfo.close_delay != port->port.close_delay) || + (newinfo.closing_wait != port->port.closing_wait) || + ((newinfo.flags & ~ASYNC_USR_MASK) != + (port->port.flags & ~ASYNC_USR_MASK))) { + mutex_unlock(&port->port.mutex); + return -EPERM; + } + port->port.flags = ((port->port.flags & ~ASYNC_USR_MASK) | + (newinfo.flags & ASYNC_USR_MASK)); + } else { + port->port.close_delay = newinfo.close_delay; + port->port.closing_wait = newinfo.closing_wait; + port->port.flags = ((port->port.flags & ~ASYNC_FLAGS) | + (newinfo.flags & ASYNC_FLAGS)); + } + if (reconfig_port) { + unsigned long flags; + spin_lock_irqsave(&port->card->card_lock, flags); + isicom_config_port(tty); + spin_unlock_irqrestore(&port->card->card_lock, flags); + } + mutex_unlock(&port->port.mutex); + return 0; +} + +static int isicom_get_serial_info(struct isi_port *port, + struct serial_struct __user *info) +{ + struct serial_struct out_info; + + mutex_lock(&port->port.mutex); + memset(&out_info, 0, sizeof(out_info)); +/* out_info.type = ? */ + out_info.line = port - isi_ports; + out_info.port = port->card->base; + out_info.irq = port->card->irq; + out_info.flags = port->port.flags; +/* out_info.baud_base = ? */ + out_info.close_delay = port->port.close_delay; + out_info.closing_wait = port->port.closing_wait; + mutex_unlock(&port->port.mutex); + if (copy_to_user(info, &out_info, sizeof(out_info))) + return -EFAULT; + return 0; +} + +static int isicom_ioctl(struct tty_struct *tty, + unsigned int cmd, unsigned long arg) +{ + struct isi_port *port = tty->driver_data; + void __user *argp = (void __user *)arg; + + if (isicom_paranoia_check(port, tty->name, "isicom_ioctl")) + return -ENODEV; + + switch (cmd) { + case TIOCGSERIAL: + return isicom_get_serial_info(port, argp); + + case TIOCSSERIAL: + return isicom_set_serial_info(tty, argp); + + default: + return -ENOIOCTLCMD; + } + return 0; +} + +/* set_termios et all */ +static void isicom_set_termios(struct tty_struct *tty, + struct ktermios *old_termios) +{ + struct isi_port *port = tty->driver_data; + unsigned long flags; + + if (isicom_paranoia_check(port, tty->name, "isicom_set_termios")) + return; + + if (tty->termios.c_cflag == old_termios->c_cflag && + tty->termios.c_iflag == old_termios->c_iflag) + return; + + spin_lock_irqsave(&port->card->card_lock, flags); + isicom_config_port(tty); + spin_unlock_irqrestore(&port->card->card_lock, flags); + + if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) { + tty->hw_stopped = 0; + isicom_start(tty); + } +} + +/* throttle et all */ +static void isicom_throttle(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + struct isi_board *card = port->card; + + if (isicom_paranoia_check(port, tty->name, "isicom_throttle")) + return; + + /* tell the card that this port cannot handle any more data for now */ + card->port_status &= ~(1 << port->channel); + outw(card->port_status, card->base + 0x02); +} + +/* unthrottle et all */ +static void isicom_unthrottle(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + struct isi_board *card = port->card; + + if (isicom_paranoia_check(port, tty->name, "isicom_unthrottle")) + return; + + /* tell the card that this port is ready to accept more data */ + card->port_status |= (1 << port->channel); + outw(card->port_status, card->base + 0x02); +} + +/* stop et all */ +static void isicom_stop(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + + if (isicom_paranoia_check(port, tty->name, "isicom_stop")) + return; + + /* this tells the transmitter not to consider this port for + data output to the card. */ + port->status &= ~ISI_TXOK; +} + +/* start et all */ +static void isicom_start(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + + if (isicom_paranoia_check(port, tty->name, "isicom_start")) + return; + + /* this tells the transmitter to consider this port for + data output to the card. */ + port->status |= ISI_TXOK; +} + +static void isicom_hangup(struct tty_struct *tty) +{ + struct isi_port *port = tty->driver_data; + + if (isicom_paranoia_check(port, tty->name, "isicom_hangup")) + return; + tty_port_hangup(&port->port); +} + + +/* + * Driver init and deinit functions + */ + +static const struct tty_operations isicom_ops = { + .open = isicom_open, + .close = isicom_close, + .write = isicom_write, + .put_char = isicom_put_char, + .flush_chars = isicom_flush_chars, + .write_room = isicom_write_room, + .chars_in_buffer = isicom_chars_in_buffer, + .ioctl = isicom_ioctl, + .set_termios = isicom_set_termios, + .throttle = isicom_throttle, + .unthrottle = isicom_unthrottle, + .stop = isicom_stop, + .start = isicom_start, + .hangup = isicom_hangup, + .flush_buffer = isicom_flush_buffer, + .tiocmget = isicom_tiocmget, + .tiocmset = isicom_tiocmset, + .break_ctl = isicom_send_break, +}; + +static const struct tty_port_operations isicom_port_ops = { + .carrier_raised = isicom_carrier_raised, + .dtr_rts = isicom_dtr_rts, + .activate = isicom_activate, + .shutdown = isicom_shutdown, +}; + +static int reset_card(struct pci_dev *pdev, + const unsigned int card, unsigned int *signature) +{ + struct isi_board *board = pci_get_drvdata(pdev); + unsigned long base = board->base; + unsigned int sig, portcount = 0; + int retval = 0; + + dev_dbg(&pdev->dev, "ISILoad:Resetting Card%d at 0x%lx\n", card + 1, + base); + + inw(base + 0x8); + + msleep(10); + + outw(0, base + 0x8); /* Reset */ + + msleep(1000); + + sig = inw(base + 0x4) & 0xff; + + if (sig != 0xa5 && sig != 0xbb && sig != 0xcc && sig != 0xdd && + sig != 0xee) { + dev_warn(&pdev->dev, "ISILoad:Card%u reset failure (Possible " + "bad I/O Port Address 0x%lx).\n", card + 1, base); + dev_dbg(&pdev->dev, "Sig=0x%x\n", sig); + retval = -EIO; + goto end; + } + + msleep(10); + + portcount = inw(base + 0x2); + if (!(inw(base + 0xe) & 0x1) || (portcount != 0 && portcount != 4 && + portcount != 8 && portcount != 16)) { + dev_err(&pdev->dev, "ISILoad:PCI Card%d reset failure.\n", + card + 1); + retval = -EIO; + goto end; + } + + switch (sig) { + case 0xa5: + case 0xbb: + case 0xdd: + board->port_count = (portcount == 4) ? 4 : 8; + board->shift_count = 12; + break; + case 0xcc: + case 0xee: + board->port_count = 16; + board->shift_count = 11; + break; + } + dev_info(&pdev->dev, "-Done\n"); + *signature = sig; + +end: + return retval; +} + +static int load_firmware(struct pci_dev *pdev, + const unsigned int index, const unsigned int signature) +{ + struct isi_board *board = pci_get_drvdata(pdev); + const struct firmware *fw; + unsigned long base = board->base; + unsigned int a; + u16 word_count, status; + int retval = -EIO; + char *name; + u8 *data; + + struct stframe { + u16 addr; + u16 count; + u8 data[0]; + } *frame; + + switch (signature) { + case 0xa5: + name = "isi608.bin"; + break; + case 0xbb: + name = "isi608em.bin"; + break; + case 0xcc: + name = "isi616em.bin"; + break; + case 0xdd: + name = "isi4608.bin"; + break; + case 0xee: + name = "isi4616.bin"; + break; + default: + dev_err(&pdev->dev, "Unknown signature.\n"); + goto end; + } + + retval = request_firmware(&fw, name, &pdev->dev); + if (retval) + goto end; + + retval = -EIO; + + for (frame = (struct stframe *)fw->data; + frame < (struct stframe *)(fw->data + fw->size); + frame = (struct stframe *)((u8 *)(frame + 1) + + frame->count)) { + if (WaitTillCardIsFree(base)) + goto errrelfw; + + outw(0xf0, base); /* start upload sequence */ + outw(0x00, base); + outw(frame->addr, base); /* lsb of address */ + + word_count = frame->count / 2 + frame->count % 2; + outw(word_count, base); + InterruptTheCard(base); + + udelay(100); /* 0x2f */ + + if (WaitTillCardIsFree(base)) + goto errrelfw; + + status = inw(base + 0x4); + if (status != 0) { + dev_warn(&pdev->dev, "Card%d rejected load header:\n" + "Address:0x%x\n" + "Count:0x%x\n" + "Status:0x%x\n", + index + 1, frame->addr, frame->count, status); + goto errrelfw; + } + outsw(base, frame->data, word_count); + + InterruptTheCard(base); + + udelay(50); /* 0x0f */ + + if (WaitTillCardIsFree(base)) + goto errrelfw; + + status = inw(base + 0x4); + if (status != 0) { + dev_err(&pdev->dev, "Card%d got out of sync.Card " + "Status:0x%x\n", index + 1, status); + goto errrelfw; + } + } + +/* XXX: should we test it by reading it back and comparing with original like + * in load firmware package? */ + for (frame = (struct stframe *)fw->data; + frame < (struct stframe *)(fw->data + fw->size); + frame = (struct stframe *)((u8 *)(frame + 1) + + frame->count)) { + if (WaitTillCardIsFree(base)) + goto errrelfw; + + outw(0xf1, base); /* start download sequence */ + outw(0x00, base); + outw(frame->addr, base); /* lsb of address */ + + word_count = (frame->count >> 1) + frame->count % 2; + outw(word_count + 1, base); + InterruptTheCard(base); + + udelay(50); /* 0xf */ + + if (WaitTillCardIsFree(base)) + goto errrelfw; + + status = inw(base + 0x4); + if (status != 0) { + dev_warn(&pdev->dev, "Card%d rejected verify header:\n" + "Address:0x%x\n" + "Count:0x%x\n" + "Status: 0x%x\n", + index + 1, frame->addr, frame->count, status); + goto errrelfw; + } + + data = kmalloc_array(word_count, 2, GFP_KERNEL); + if (data == NULL) { + dev_err(&pdev->dev, "Card%d, firmware upload " + "failed, not enough memory\n", index + 1); + goto errrelfw; + } + inw(base); + insw(base, data, word_count); + InterruptTheCard(base); + + for (a = 0; a < frame->count; a++) + if (data[a] != frame->data[a]) { + kfree(data); + dev_err(&pdev->dev, "Card%d, firmware upload " + "failed\n", index + 1); + goto errrelfw; + } + kfree(data); + + udelay(50); /* 0xf */ + + if (WaitTillCardIsFree(base)) + goto errrelfw; + + status = inw(base + 0x4); + if (status != 0) { + dev_err(&pdev->dev, "Card%d verify got out of sync. " + "Card Status:0x%x\n", index + 1, status); + goto errrelfw; + } + } + + /* xfer ctrl */ + if (WaitTillCardIsFree(base)) + goto errrelfw; + + outw(0xf2, base); + outw(0x800, base); + outw(0x0, base); + outw(0x0, base); + InterruptTheCard(base); + outw(0x0, base + 0x4); /* for ISI4608 cards */ + + board->status |= FIRMWARE_LOADED; + retval = 0; + +errrelfw: + release_firmware(fw); +end: + return retval; +} + +/* + * Insmod can set static symbols so keep these static + */ +static unsigned int card_count; + +static int isicom_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + unsigned int uninitialized_var(signature), index; + int retval = -EPERM; + struct isi_board *board = NULL; + + if (card_count >= BOARD_COUNT) + goto err; + + retval = pci_enable_device(pdev); + if (retval) { + dev_err(&pdev->dev, "failed to enable\n"); + goto err; + } + + dev_info(&pdev->dev, "ISI PCI Card(Device ID 0x%x)\n", ent->device); + + /* allot the first empty slot in the array */ + for (index = 0; index < BOARD_COUNT; index++) { + if (isi_card[index].base == 0) { + board = &isi_card[index]; + break; + } + } + if (index == BOARD_COUNT) { + retval = -ENODEV; + goto err_disable; + } + + board->index = index; + board->base = pci_resource_start(pdev, 3); + board->irq = pdev->irq; + card_count++; + + pci_set_drvdata(pdev, board); + + retval = pci_request_region(pdev, 3, ISICOM_NAME); + if (retval) { + dev_err(&pdev->dev, "I/O Region 0x%lx-0x%lx is busy. Card%d " + "will be disabled.\n", board->base, board->base + 15, + index + 1); + retval = -EBUSY; + goto errdec; + } + + retval = request_irq(board->irq, isicom_interrupt, + IRQF_SHARED, ISICOM_NAME, board); + if (retval < 0) { + dev_err(&pdev->dev, "Could not install handler at Irq %d. " + "Card%d will be disabled.\n", board->irq, index + 1); + goto errunrr; + } + + retval = reset_card(pdev, index, &signature); + if (retval < 0) + goto errunri; + + retval = load_firmware(pdev, index, signature); + if (retval < 0) + goto errunri; + + for (index = 0; index < board->port_count; index++) { + struct tty_port *tport = &board->ports[index].port; + tty_port_init(tport); + tport->ops = &isicom_port_ops; + tport->close_delay = 50 * HZ/100; + tport->closing_wait = 3000 * HZ/100; + tty_port_register_device(tport, isicom_normal, + board->index * 16 + index, &pdev->dev); + } + + return 0; + +errunri: + free_irq(board->irq, board); +errunrr: + pci_release_region(pdev, 3); +errdec: + board->base = 0; + card_count--; +err_disable: + pci_disable_device(pdev); +err: + return retval; +} + +static void isicom_remove(struct pci_dev *pdev) +{ + struct isi_board *board = pci_get_drvdata(pdev); + unsigned int i; + + for (i = 0; i < board->port_count; i++) { + tty_unregister_device(isicom_normal, board->index * 16 + i); + tty_port_destroy(&board->ports[i].port); + } + + free_irq(board->irq, board); + pci_release_region(pdev, 3); + board->base = 0; + card_count--; + pci_disable_device(pdev); +} + +static int __init isicom_init(void) +{ + int retval, idx, channel; + struct isi_port *port; + + for (idx = 0; idx < BOARD_COUNT; idx++) { + port = &isi_ports[idx * 16]; + isi_card[idx].ports = port; + spin_lock_init(&isi_card[idx].card_lock); + for (channel = 0; channel < 16; channel++, port++) { + port->magic = ISICOM_MAGIC; + port->card = &isi_card[idx]; + port->channel = channel; + port->status = 0; + /* . . . */ + } + isi_card[idx].base = 0; + isi_card[idx].irq = 0; + } + + /* tty driver structure initialization */ + isicom_normal = alloc_tty_driver(PORT_COUNT); + if (!isicom_normal) { + retval = -ENOMEM; + goto error; + } + + isicom_normal->name = "ttyM"; + isicom_normal->major = ISICOM_NMAJOR; + isicom_normal->minor_start = 0; + isicom_normal->type = TTY_DRIVER_TYPE_SERIAL; + isicom_normal->subtype = SERIAL_TYPE_NORMAL; + isicom_normal->init_termios = tty_std_termios; + isicom_normal->init_termios.c_cflag = B9600 | CS8 | CREAD | HUPCL | + CLOCAL; + isicom_normal->flags = TTY_DRIVER_REAL_RAW | + TTY_DRIVER_DYNAMIC_DEV | TTY_DRIVER_HARDWARE_BREAK; + tty_set_operations(isicom_normal, &isicom_ops); + + retval = tty_register_driver(isicom_normal); + if (retval) { + pr_debug("Couldn't register the dialin driver\n"); + goto err_puttty; + } + + retval = pci_register_driver(&isicom_driver); + if (retval < 0) { + pr_err("Unable to register pci driver.\n"); + goto err_unrtty; + } + + mod_timer(&tx, jiffies + 1); + + return 0; +err_unrtty: + tty_unregister_driver(isicom_normal); +err_puttty: + put_tty_driver(isicom_normal); +error: + return retval; +} + +static void __exit isicom_exit(void) +{ + del_timer_sync(&tx); + + pci_unregister_driver(&isicom_driver); + tty_unregister_driver(isicom_normal); + put_tty_driver(isicom_normal); +} + +module_init(isicom_init); +module_exit(isicom_exit); + +MODULE_AUTHOR("MultiTech"); +MODULE_DESCRIPTION("Driver for the ISI series of cards by MultiTech"); +MODULE_LICENSE("GPL"); +MODULE_FIRMWARE("isi608.bin"); +MODULE_FIRMWARE("isi608em.bin"); +MODULE_FIRMWARE("isi616em.bin"); +MODULE_FIRMWARE("isi4608.bin"); +MODULE_FIRMWARE("isi4616.bin"); |