diff options
Diffstat (limited to 'drivers/tty/serial/jsm/jsm.h')
| -rw-r--r-- | drivers/tty/serial/jsm/jsm.h | 438 |
1 files changed, 438 insertions, 0 deletions
diff --git a/drivers/tty/serial/jsm/jsm.h b/drivers/tty/serial/jsm/jsm.h new file mode 100644 index 000000000..7a128aaa3 --- /dev/null +++ b/drivers/tty/serial/jsm/jsm.h @@ -0,0 +1,438 @@ +// SPDX-License-Identifier: GPL-2.0+ +/************************************************************************ + * Copyright 2003 Digi International (www.digi.com) + * + * Copyright (C) 2004 IBM Corporation. All rights reserved. + * + * Contact Information: + * Scott H Kilau <Scott_Kilau@digi.com> + * Wendy Xiong <wendyx@us.ibm.com> + * + ***********************************************************************/ + +#ifndef __JSM_DRIVER_H +#define __JSM_DRIVER_H + +#include <linux/kernel.h> +#include <linux/types.h> /* To pick up the varions Linux types */ +#include <linux/tty.h> +#include <linux/serial_core.h> +#include <linux/device.h> + +/* + * Debugging levels can be set using debug insmod variable + * They can also be compiled out completely. + */ +enum { + DBG_INIT = 0x01, + DBG_BASIC = 0x02, + DBG_CORE = 0x04, + DBG_OPEN = 0x08, + DBG_CLOSE = 0x10, + DBG_READ = 0x20, + DBG_WRITE = 0x40, + DBG_IOCTL = 0x80, + DBG_PROC = 0x100, + DBG_PARAM = 0x200, + DBG_PSCAN = 0x400, + DBG_EVENT = 0x800, + DBG_DRAIN = 0x1000, + DBG_MSIGS = 0x2000, + DBG_MGMT = 0x4000, + DBG_INTR = 0x8000, + DBG_CARR = 0x10000, +}; + +#define jsm_dbg(nlevel, pdev, fmt, ...) \ +do { \ + if (DBG_##nlevel & jsm_debug) \ + dev_dbg(pdev->dev, fmt, ##__VA_ARGS__); \ +} while (0) + +#define MAXLINES 256 +#define MAXPORTS 8 +#define MAX_STOPS_SENT 5 + +/* Board ids */ +#define PCI_DEVICE_ID_CLASSIC_4 0x0028 +#define PCI_DEVICE_ID_CLASSIC_8 0x0029 +#define PCI_DEVICE_ID_CLASSIC_4_422 0x00D0 +#define PCI_DEVICE_ID_CLASSIC_8_422 0x00D1 +#define PCI_DEVICE_ID_NEO_4 0x00B0 +#define PCI_DEVICE_ID_NEO_1_422 0x00CC +#define PCI_DEVICE_ID_NEO_1_422_485 0x00CD +#define PCI_DEVICE_ID_NEO_2_422_485 0x00CE +#define PCIE_DEVICE_ID_NEO_8 0x00F0 +#define PCIE_DEVICE_ID_NEO_4 0x00F1 +#define PCIE_DEVICE_ID_NEO_4RJ45 0x00F2 +#define PCIE_DEVICE_ID_NEO_8RJ45 0x00F3 + +/* Board type definitions */ + +#define T_NEO 0000 +#define T_CLASSIC 0001 +#define T_PCIBUS 0400 + +/* Board State Definitions */ + +#define BD_RUNNING 0x0 +#define BD_REASON 0x7f +#define BD_NOTFOUND 0x1 +#define BD_NOIOPORT 0x2 +#define BD_NOMEM 0x3 +#define BD_NOBIOS 0x4 +#define BD_NOFEP 0x5 +#define BD_FAILED 0x6 +#define BD_ALLOCATED 0x7 +#define BD_TRIBOOT 0x8 +#define BD_BADKME 0x80 + + +/* 4 extra for alignment play space */ +#define WRITEBUFLEN ((4096) + 4) + +#define JSM_VERSION "jsm: 1.2-1-INKERNEL" +#define JSM_PARTNUM "40002438_A-INKERNEL" + +struct jsm_board; +struct jsm_channel; + +/************************************************************************ + * Per board operations structure * + ************************************************************************/ +struct board_ops { + irq_handler_t intr; + void (*uart_init)(struct jsm_channel *ch); + void (*uart_off)(struct jsm_channel *ch); + void (*param)(struct jsm_channel *ch); + void (*assert_modem_signals)(struct jsm_channel *ch); + void (*flush_uart_write)(struct jsm_channel *ch); + void (*flush_uart_read)(struct jsm_channel *ch); + void (*disable_receiver)(struct jsm_channel *ch); + void (*enable_receiver)(struct jsm_channel *ch); + void (*send_break)(struct jsm_channel *ch); + void (*clear_break)(struct jsm_channel *ch); + void (*send_start_character)(struct jsm_channel *ch); + void (*send_stop_character)(struct jsm_channel *ch); + void (*copy_data_from_queue_to_uart)(struct jsm_channel *ch); + u32 (*get_uart_bytes_left)(struct jsm_channel *ch); + void (*send_immediate_char)(struct jsm_channel *ch, unsigned char); +}; + + +/* + * Per-board information + */ +struct jsm_board +{ + int boardnum; /* Board number: 0-32 */ + + int type; /* Type of board */ + u8 rev; /* PCI revision ID */ + struct pci_dev *pci_dev; + u32 maxports; /* MAX ports this board can handle */ + + spinlock_t bd_intr_lock; /* Used to protect the poller tasklet and + * the interrupt routine from each other. + */ + + u32 nasync; /* Number of ports on card */ + + u32 irq; /* Interrupt request number */ + + u64 membase; /* Start of base memory of the card */ + u64 membase_end; /* End of base memory of the card */ + + u8 __iomem *re_map_membase;/* Remapped memory of the card */ + + u64 iobase; /* Start of io base of the card */ + u64 iobase_end; /* End of io base of the card */ + + u32 bd_uart_offset; /* Space between each UART */ + + struct jsm_channel *channels[MAXPORTS]; /* array of pointers to our channels. */ + + u32 bd_dividend; /* Board/UARTs specific dividend */ + + struct board_ops *bd_ops; + + struct list_head jsm_board_entry; +}; + +/************************************************************************ + * Device flag definitions for ch_flags. + ************************************************************************/ +#define CH_PRON 0x0001 /* Printer on string */ +#define CH_STOP 0x0002 /* Output is stopped */ +#define CH_STOPI 0x0004 /* Input is stopped */ +#define CH_CD 0x0008 /* Carrier is present */ +#define CH_FCAR 0x0010 /* Carrier forced on */ +#define CH_HANGUP 0x0020 /* Hangup received */ + +#define CH_RECEIVER_OFF 0x0040 /* Receiver is off */ +#define CH_OPENING 0x0080 /* Port in fragile open state */ +#define CH_CLOSING 0x0100 /* Port in fragile close state */ +#define CH_FIFO_ENABLED 0x0200 /* Port has FIFOs enabled */ +#define CH_TX_FIFO_EMPTY 0x0400 /* TX Fifo is completely empty */ +#define CH_TX_FIFO_LWM 0x0800 /* TX Fifo is below Low Water */ +#define CH_BREAK_SENDING 0x1000 /* Break is being sent */ +#define CH_LOOPBACK 0x2000 /* Channel is in lookback mode */ +#define CH_BAUD0 0x08000 /* Used for checking B0 transitions */ + +/* Our Read/Error queue sizes */ +#define RQUEUEMASK 0x1FFF /* 8 K - 1 */ +#define EQUEUEMASK 0x1FFF /* 8 K - 1 */ +#define RQUEUESIZE (RQUEUEMASK + 1) +#define EQUEUESIZE RQUEUESIZE + + +/************************************************************************ + * Channel information structure. + ************************************************************************/ +struct jsm_channel { + struct uart_port uart_port; + struct jsm_board *ch_bd; /* Board structure pointer */ + + spinlock_t ch_lock; /* provide for serialization */ + wait_queue_head_t ch_flags_wait; + + u32 ch_portnum; /* Port number, 0 offset. */ + u32 ch_open_count; /* open count */ + u32 ch_flags; /* Channel flags */ + + u64 ch_close_delay; /* How long we should drop RTS/DTR for */ + + tcflag_t ch_c_iflag; /* channel iflags */ + tcflag_t ch_c_cflag; /* channel cflags */ + tcflag_t ch_c_oflag; /* channel oflags */ + tcflag_t ch_c_lflag; /* channel lflags */ + u8 ch_stopc; /* Stop character */ + u8 ch_startc; /* Start character */ + + u8 ch_mostat; /* FEP output modem status */ + u8 ch_mistat; /* FEP input modem status */ + + /* Pointers to the "mapped" UART structs */ + struct neo_uart_struct __iomem *ch_neo_uart; /* NEO card */ + struct cls_uart_struct __iomem *ch_cls_uart; /* Classic card */ + + u8 ch_cached_lsr; /* Cached value of the LSR register */ + + u8 *ch_rqueue; /* Our read queue buffer - malloc'ed */ + u16 ch_r_head; /* Head location of the read queue */ + u16 ch_r_tail; /* Tail location of the read queue */ + + u8 *ch_equeue; /* Our error queue buffer - malloc'ed */ + u16 ch_e_head; /* Head location of the error queue */ + u16 ch_e_tail; /* Tail location of the error queue */ + + u64 ch_rxcount; /* total of data received so far */ + u64 ch_txcount; /* total of data transmitted so far */ + + u8 ch_r_tlevel; /* Receive Trigger level */ + u8 ch_t_tlevel; /* Transmit Trigger level */ + + u8 ch_r_watermark; /* Receive Watermark */ + + + u32 ch_stops_sent; /* How many times I have sent a stop character + * to try to stop the other guy sending. + */ + u64 ch_err_parity; /* Count of parity errors on channel */ + u64 ch_err_frame; /* Count of framing errors on channel */ + u64 ch_err_break; /* Count of breaks on channel */ + u64 ch_err_overrun; /* Count of overruns on channel */ + + u64 ch_xon_sends; /* Count of xons transmitted */ + u64 ch_xoff_sends; /* Count of xoffs transmitted */ +}; + +/************************************************************************ + * Per channel/port Classic UART structures * + ************************************************************************ + * Base Structure Entries Usage Meanings to Host * + * * + * W = read write R = read only * + * U = Unused. * + ************************************************************************/ + +struct cls_uart_struct { + u8 txrx; /* WR RHR/THR - Holding Reg */ + u8 ier; /* WR IER - Interrupt Enable Reg */ + u8 isr_fcr; /* WR ISR/FCR - Interrupt Status Reg/Fifo Control Reg*/ + u8 lcr; /* WR LCR - Line Control Reg */ + u8 mcr; /* WR MCR - Modem Control Reg */ + u8 lsr; /* WR LSR - Line Status Reg */ + u8 msr; /* WR MSR - Modem Status Reg */ + u8 spr; /* WR SPR - Scratch Pad Reg */ +}; + +/* Where to read the interrupt register (8bits) */ +#define UART_CLASSIC_POLL_ADDR_OFFSET 0x40 + +#define UART_EXAR654_ENHANCED_REGISTER_SET 0xBF + +#define UART_16654_FCR_TXTRIGGER_8 0x0 +#define UART_16654_FCR_TXTRIGGER_16 0x10 +#define UART_16654_FCR_TXTRIGGER_32 0x20 +#define UART_16654_FCR_TXTRIGGER_56 0x30 + +#define UART_16654_FCR_RXTRIGGER_8 0x0 +#define UART_16654_FCR_RXTRIGGER_16 0x40 +#define UART_16654_FCR_RXTRIGGER_56 0x80 +#define UART_16654_FCR_RXTRIGGER_60 0xC0 + +#define UART_IIR_CTSRTS 0x20 /* Received CTS/RTS change of state */ +#define UART_IIR_RDI_TIMEOUT 0x0C /* Receiver data TIMEOUT */ + +/* + * These are the EXTENDED definitions for the Exar 654's Interrupt + * Enable Register. + */ +#define UART_EXAR654_EFR_ECB 0x10 /* Enhanced control bit */ +#define UART_EXAR654_EFR_IXON 0x2 /* Receiver compares Xon1/Xoff1 */ +#define UART_EXAR654_EFR_IXOFF 0x8 /* Transmit Xon1/Xoff1 */ +#define UART_EXAR654_EFR_RTSDTR 0x40 /* Auto RTS/DTR Flow Control Enable */ +#define UART_EXAR654_EFR_CTSDSR 0x80 /* Auto CTS/DSR Flow COntrol Enable */ + +#define UART_EXAR654_XOFF_DETECT 0x1 /* Indicates whether chip saw an incoming XOFF char */ +#define UART_EXAR654_XON_DETECT 0x2 /* Indicates whether chip saw an incoming XON char */ + +#define UART_EXAR654_IER_XOFF 0x20 /* Xoff Interrupt Enable */ +#define UART_EXAR654_IER_RTSDTR 0x40 /* Output Interrupt Enable */ +#define UART_EXAR654_IER_CTSDSR 0x80 /* Input Interrupt Enable */ + +/************************************************************************ + * Per channel/port NEO UART structure * + ************************************************************************ + * Base Structure Entries Usage Meanings to Host * + * * + * W = read write R = read only * + * U = Unused. * + ************************************************************************/ + +struct neo_uart_struct { + u8 txrx; /* WR RHR/THR - Holding Reg */ + u8 ier; /* WR IER - Interrupt Enable Reg */ + u8 isr_fcr; /* WR ISR/FCR - Interrupt Status Reg/Fifo Control Reg */ + u8 lcr; /* WR LCR - Line Control Reg */ + u8 mcr; /* WR MCR - Modem Control Reg */ + u8 lsr; /* WR LSR - Line Status Reg */ + u8 msr; /* WR MSR - Modem Status Reg */ + u8 spr; /* WR SPR - Scratch Pad Reg */ + u8 fctr; /* WR FCTR - Feature Control Reg */ + u8 efr; /* WR EFR - Enhanced Function Reg */ + u8 tfifo; /* WR TXCNT/TXTRG - Transmit FIFO Reg */ + u8 rfifo; /* WR RXCNT/RXTRG - Receive FIFO Reg */ + u8 xoffchar1; /* WR XOFF 1 - XOff Character 1 Reg */ + u8 xoffchar2; /* WR XOFF 2 - XOff Character 2 Reg */ + u8 xonchar1; /* WR XON 1 - Xon Character 1 Reg */ + u8 xonchar2; /* WR XON 2 - XOn Character 2 Reg */ + + u8 reserved1[0x2ff - 0x200]; /* U Reserved by Exar */ + u8 txrxburst[64]; /* RW 64 bytes of RX/TX FIFO Data */ + u8 reserved2[0x37f - 0x340]; /* U Reserved by Exar */ + u8 rxburst_with_errors[64]; /* R 64 bytes of RX FIFO Data + LSR */ +}; + +/* Where to read the extended interrupt register (32bits instead of 8bits) */ +#define UART_17158_POLL_ADDR_OFFSET 0x80 + +/* + * These are the redefinitions for the FCTR on the XR17C158, since + * Exar made them different than their earlier design. (XR16C854) + */ + +/* These are only applicable when table D is selected */ +#define UART_17158_FCTR_RTS_NODELAY 0x00 +#define UART_17158_FCTR_RTS_4DELAY 0x01 +#define UART_17158_FCTR_RTS_6DELAY 0x02 +#define UART_17158_FCTR_RTS_8DELAY 0x03 +#define UART_17158_FCTR_RTS_12DELAY 0x12 +#define UART_17158_FCTR_RTS_16DELAY 0x05 +#define UART_17158_FCTR_RTS_20DELAY 0x13 +#define UART_17158_FCTR_RTS_24DELAY 0x06 +#define UART_17158_FCTR_RTS_28DELAY 0x14 +#define UART_17158_FCTR_RTS_32DELAY 0x07 +#define UART_17158_FCTR_RTS_36DELAY 0x16 +#define UART_17158_FCTR_RTS_40DELAY 0x08 +#define UART_17158_FCTR_RTS_44DELAY 0x09 +#define UART_17158_FCTR_RTS_48DELAY 0x10 +#define UART_17158_FCTR_RTS_52DELAY 0x11 + +#define UART_17158_FCTR_RTS_IRDA 0x10 +#define UART_17158_FCTR_RS485 0x20 +#define UART_17158_FCTR_TRGA 0x00 +#define UART_17158_FCTR_TRGB 0x40 +#define UART_17158_FCTR_TRGC 0x80 +#define UART_17158_FCTR_TRGD 0xC0 + +/* 17158 trigger table selects.. */ +#define UART_17158_FCTR_BIT6 0x40 +#define UART_17158_FCTR_BIT7 0x80 + +/* 17158 TX/RX memmapped buffer offsets */ +#define UART_17158_RX_FIFOSIZE 64 +#define UART_17158_TX_FIFOSIZE 64 + +/* 17158 Extended IIR's */ +#define UART_17158_IIR_RDI_TIMEOUT 0x0C /* Receiver data TIMEOUT */ +#define UART_17158_IIR_XONXOFF 0x10 /* Received an XON/XOFF char */ +#define UART_17158_IIR_HWFLOW_STATE_CHANGE 0x20 /* CTS/DSR or RTS/DTR state change */ +#define UART_17158_IIR_FIFO_ENABLED 0xC0 /* 16550 FIFOs are Enabled */ + +/* + * These are the extended interrupts that get sent + * back to us from the UART's 32bit interrupt register + */ +#define UART_17158_RX_LINE_STATUS 0x1 /* RX Ready */ +#define UART_17158_RXRDY_TIMEOUT 0x2 /* RX Ready Timeout */ +#define UART_17158_TXRDY 0x3 /* TX Ready */ +#define UART_17158_MSR 0x4 /* Modem State Change */ +#define UART_17158_TX_AND_FIFO_CLR 0x40 /* Transmitter Holding Reg Empty */ +#define UART_17158_RX_FIFO_DATA_ERROR 0x80 /* UART detected an RX FIFO Data error */ + +/* + * These are the EXTENDED definitions for the 17C158's Interrupt + * Enable Register. + */ +#define UART_17158_EFR_ECB 0x10 /* Enhanced control bit */ +#define UART_17158_EFR_IXON 0x2 /* Receiver compares Xon1/Xoff1 */ +#define UART_17158_EFR_IXOFF 0x8 /* Transmit Xon1/Xoff1 */ +#define UART_17158_EFR_RTSDTR 0x40 /* Auto RTS/DTR Flow Control Enable */ +#define UART_17158_EFR_CTSDSR 0x80 /* Auto CTS/DSR Flow COntrol Enable */ + +#define UART_17158_XOFF_DETECT 0x1 /* Indicates whether chip saw an incoming XOFF char */ +#define UART_17158_XON_DETECT 0x2 /* Indicates whether chip saw an incoming XON char */ + +#define UART_17158_IER_RSVD1 0x10 /* Reserved by Exar */ +#define UART_17158_IER_XOFF 0x20 /* Xoff Interrupt Enable */ +#define UART_17158_IER_RTSDTR 0x40 /* Output Interrupt Enable */ +#define UART_17158_IER_CTSDSR 0x80 /* Input Interrupt Enable */ + +#define PCI_DEVICE_NEO_2DB9_PCI_NAME "Neo 2 - DB9 Universal PCI" +#define PCI_DEVICE_NEO_2DB9PRI_PCI_NAME "Neo 2 - DB9 Universal PCI - Powered Ring Indicator" +#define PCI_DEVICE_NEO_2RJ45_PCI_NAME "Neo 2 - RJ45 Universal PCI" +#define PCI_DEVICE_NEO_2RJ45PRI_PCI_NAME "Neo 2 - RJ45 Universal PCI - Powered Ring Indicator" +#define PCIE_DEVICE_NEO_IBM_PCI_NAME "Neo 4 - PCI Express - IBM" + +/* + * Our Global Variables. + */ +extern struct uart_driver jsm_uart_driver; +extern struct board_ops jsm_neo_ops; +extern struct board_ops jsm_cls_ops; +extern int jsm_debug; + +/************************************************************************* + * + * Prototypes for non-static functions used in more than one module + * + *************************************************************************/ +int jsm_tty_init(struct jsm_board *); +int jsm_uart_port_init(struct jsm_board *); +int jsm_remove_uart_port(struct jsm_board *); +void jsm_input(struct jsm_channel *ch); +void jsm_check_queue_flow_control(struct jsm_channel *ch); + +#endif |