diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/tty/serial/pnx8xxx_uart.c | 863 |
1 files changed, 863 insertions, 0 deletions
diff --git a/drivers/tty/serial/pnx8xxx_uart.c b/drivers/tty/serial/pnx8xxx_uart.c new file mode 100644 index 000000000..223a94991 --- /dev/null +++ b/drivers/tty/serial/pnx8xxx_uart.c @@ -0,0 +1,863 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * UART driver for PNX8XXX SoCs + * + * Author: Per Hallsmark per.hallsmark@mvista.com + * Ported to 2.6 kernel by EmbeddedAlley + * Reworked by Vitaly Wool <vitalywool@gmail.com> + * + * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. + * Copyright (C) 2000 Deep Blue Solutions Ltd. + */ + +#if defined(CONFIG_SERIAL_PNX8XXX_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/device.h> +#include <linux/platform_device.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/serial_pnx8xxx.h> + +#include <asm/io.h> +#include <asm/irq.h> + +/* We'll be using StrongARM sa1100 serial port major/minor */ +#define SERIAL_PNX8XXX_MAJOR 204 +#define MINOR_START 5 + +#define NR_PORTS 2 + +#define PNX8XXX_ISR_PASS_LIMIT 256 + +/* + * Convert from ignore_status_mask or read_status_mask to FIFO + * and interrupt status bits + */ +#define SM_TO_FIFO(x) ((x) >> 10) +#define SM_TO_ISTAT(x) ((x) & 0x000001ff) +#define FIFO_TO_SM(x) ((x) << 10) +#define ISTAT_TO_SM(x) ((x) & 0x000001ff) + +/* + * This is the size of our serial port register set. + */ +#define UART_PORT_SIZE 0x1000 + +/* + * This determines how often we check the modem status signals + * for any change. They generally aren't connected to an IRQ + * so we have to poll them. We also check immediately before + * filling the TX fifo incase CTS has been dropped. + */ +#define MCTRL_TIMEOUT (250*HZ/1000) + +extern struct pnx8xxx_port pnx8xxx_ports[]; + +static inline int serial_in(struct pnx8xxx_port *sport, int offset) +{ + return (__raw_readl(sport->port.membase + offset)); +} + +static inline void serial_out(struct pnx8xxx_port *sport, int offset, int value) +{ + __raw_writel(value, sport->port.membase + offset); +} + +/* + * Handle any change of modem status signal since we were last called. + */ +static void pnx8xxx_mctrl_check(struct pnx8xxx_port *sport) +{ + unsigned int status, changed; + + status = sport->port.ops->get_mctrl(&sport->port); + changed = status ^ sport->old_status; + + if (changed == 0) + return; + + sport->old_status = status; + + if (changed & TIOCM_RI) + sport->port.icount.rng++; + if (changed & TIOCM_DSR) + sport->port.icount.dsr++; + if (changed & TIOCM_CAR) + uart_handle_dcd_change(&sport->port, status & TIOCM_CAR); + if (changed & TIOCM_CTS) + uart_handle_cts_change(&sport->port, status & TIOCM_CTS); + + wake_up_interruptible(&sport->port.state->port.delta_msr_wait); +} + +/* + * This is our per-port timeout handler, for checking the + * modem status signals. + */ +static void pnx8xxx_timeout(struct timer_list *t) +{ + struct pnx8xxx_port *sport = from_timer(sport, t, timer); + unsigned long flags; + + if (sport->port.state) { + spin_lock_irqsave(&sport->port.lock, flags); + pnx8xxx_mctrl_check(sport); + spin_unlock_irqrestore(&sport->port.lock, flags); + + mod_timer(&sport->timer, jiffies + MCTRL_TIMEOUT); + } +} + +/* + * interrupts disabled on entry + */ +static void pnx8xxx_stop_tx(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + u32 ien; + + /* Disable TX intr */ + ien = serial_in(sport, PNX8XXX_IEN); + serial_out(sport, PNX8XXX_IEN, ien & ~PNX8XXX_UART_INT_ALLTX); + + /* Clear all pending TX intr */ + serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLTX); +} + +/* + * interrupts may not be disabled on entry + */ +static void pnx8xxx_start_tx(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + u32 ien; + + /* Clear all pending TX intr */ + serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLTX); + + /* Enable TX intr */ + ien = serial_in(sport, PNX8XXX_IEN); + serial_out(sport, PNX8XXX_IEN, ien | PNX8XXX_UART_INT_ALLTX); +} + +/* + * Interrupts enabled + */ +static void pnx8xxx_stop_rx(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + u32 ien; + + /* Disable RX intr */ + ien = serial_in(sport, PNX8XXX_IEN); + serial_out(sport, PNX8XXX_IEN, ien & ~PNX8XXX_UART_INT_ALLRX); + + /* Clear all pending RX intr */ + serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLRX); +} + +/* + * Set the modem control timer to fire immediately. + */ +static void pnx8xxx_enable_ms(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + + mod_timer(&sport->timer, jiffies); +} + +static void pnx8xxx_rx_chars(struct pnx8xxx_port *sport) +{ + unsigned int status, ch, flg; + + status = FIFO_TO_SM(serial_in(sport, PNX8XXX_FIFO)) | + ISTAT_TO_SM(serial_in(sport, PNX8XXX_ISTAT)); + while (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFIFO)) { + ch = serial_in(sport, PNX8XXX_FIFO) & 0xff; + + sport->port.icount.rx++; + + flg = TTY_NORMAL; + + /* + * note that the error handling code is + * out of the main execution path + */ + if (status & (FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE | + PNX8XXX_UART_FIFO_RXPAR | + PNX8XXX_UART_FIFO_RXBRK) | + ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN))) { + if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXBRK)) { + status &= ~(FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE) | + FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR)); + sport->port.icount.brk++; + if (uart_handle_break(&sport->port)) + goto ignore_char; + } else if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR)) + sport->port.icount.parity++; + else if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE)) + sport->port.icount.frame++; + if (status & ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN)) + sport->port.icount.overrun++; + + status &= sport->port.read_status_mask; + + if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR)) + flg = TTY_PARITY; + else if (status & FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE)) + flg = TTY_FRAME; + +#ifdef SUPPORT_SYSRQ + sport->port.sysrq = 0; +#endif + } + + if (uart_handle_sysrq_char(&sport->port, ch)) + goto ignore_char; + + uart_insert_char(&sport->port, status, + ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN), ch, flg); + + ignore_char: + serial_out(sport, PNX8XXX_LCR, serial_in(sport, PNX8XXX_LCR) | + PNX8XXX_UART_LCR_RX_NEXT); + status = FIFO_TO_SM(serial_in(sport, PNX8XXX_FIFO)) | + ISTAT_TO_SM(serial_in(sport, PNX8XXX_ISTAT)); + } + + spin_unlock(&sport->port.lock); + tty_flip_buffer_push(&sport->port.state->port); + spin_lock(&sport->port.lock); +} + +static void pnx8xxx_tx_chars(struct pnx8xxx_port *sport) +{ + struct circ_buf *xmit = &sport->port.state->xmit; + + if (sport->port.x_char) { + serial_out(sport, PNX8XXX_FIFO, sport->port.x_char); + sport->port.icount.tx++; + sport->port.x_char = 0; + return; + } + + /* + * Check the modem control lines before + * transmitting anything. + */ + pnx8xxx_mctrl_check(sport); + + if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) { + pnx8xxx_stop_tx(&sport->port); + return; + } + + /* + * TX while bytes available + */ + while (((serial_in(sport, PNX8XXX_FIFO) & + PNX8XXX_UART_FIFO_TXFIFO) >> 16) < 16) { + serial_out(sport, PNX8XXX_FIFO, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + sport->port.icount.tx++; + if (uart_circ_empty(xmit)) + break; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&sport->port); + + if (uart_circ_empty(xmit)) + pnx8xxx_stop_tx(&sport->port); +} + +static irqreturn_t pnx8xxx_int(int irq, void *dev_id) +{ + struct pnx8xxx_port *sport = dev_id; + unsigned int status; + + spin_lock(&sport->port.lock); + /* Get the interrupts */ + status = serial_in(sport, PNX8XXX_ISTAT) & serial_in(sport, PNX8XXX_IEN); + + /* Byte or break signal received */ + if (status & (PNX8XXX_UART_INT_RX | PNX8XXX_UART_INT_BREAK)) + pnx8xxx_rx_chars(sport); + + /* TX holding register empty - transmit a byte */ + if (status & PNX8XXX_UART_INT_TX) + pnx8xxx_tx_chars(sport); + + /* Clear the ISTAT register */ + serial_out(sport, PNX8XXX_ICLR, status); + + spin_unlock(&sport->port.lock); + return IRQ_HANDLED; +} + +/* + * Return TIOCSER_TEMT when transmitter is not busy. + */ +static unsigned int pnx8xxx_tx_empty(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + + return serial_in(sport, PNX8XXX_FIFO) & PNX8XXX_UART_FIFO_TXFIFO_STA ? 0 : TIOCSER_TEMT; +} + +static unsigned int pnx8xxx_get_mctrl(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + unsigned int mctrl = TIOCM_DSR; + unsigned int msr; + + /* REVISIT */ + + msr = serial_in(sport, PNX8XXX_MCR); + + mctrl |= msr & PNX8XXX_UART_MCR_CTS ? TIOCM_CTS : 0; + mctrl |= msr & PNX8XXX_UART_MCR_DCD ? TIOCM_CAR : 0; + + return mctrl; +} + +static void pnx8xxx_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ +#if 0 /* FIXME */ + struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port; + unsigned int msr; +#endif +} + +/* + * Interrupts always disabled. + */ +static void pnx8xxx_break_ctl(struct uart_port *port, int break_state) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + unsigned long flags; + unsigned int lcr; + + spin_lock_irqsave(&sport->port.lock, flags); + lcr = serial_in(sport, PNX8XXX_LCR); + if (break_state == -1) + lcr |= PNX8XXX_UART_LCR_TXBREAK; + else + lcr &= ~PNX8XXX_UART_LCR_TXBREAK; + serial_out(sport, PNX8XXX_LCR, lcr); + spin_unlock_irqrestore(&sport->port.lock, flags); +} + +static int pnx8xxx_startup(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + int retval; + + /* + * Allocate the IRQ + */ + retval = request_irq(sport->port.irq, pnx8xxx_int, 0, + "pnx8xxx-uart", sport); + if (retval) + return retval; + + /* + * Finally, clear and enable interrupts + */ + + serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLRX | + PNX8XXX_UART_INT_ALLTX); + + serial_out(sport, PNX8XXX_IEN, serial_in(sport, PNX8XXX_IEN) | + PNX8XXX_UART_INT_ALLRX | + PNX8XXX_UART_INT_ALLTX); + + /* + * Enable modem status interrupts + */ + spin_lock_irq(&sport->port.lock); + pnx8xxx_enable_ms(&sport->port); + spin_unlock_irq(&sport->port.lock); + + return 0; +} + +static void pnx8xxx_shutdown(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + int lcr; + + /* + * Stop our timer. + */ + del_timer_sync(&sport->timer); + + /* + * Disable all interrupts + */ + serial_out(sport, PNX8XXX_IEN, 0); + + /* + * Reset the Tx and Rx FIFOS, disable the break condition + */ + lcr = serial_in(sport, PNX8XXX_LCR); + lcr &= ~PNX8XXX_UART_LCR_TXBREAK; + lcr |= PNX8XXX_UART_LCR_TX_RST | PNX8XXX_UART_LCR_RX_RST; + serial_out(sport, PNX8XXX_LCR, lcr); + + /* + * Clear all interrupts + */ + serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLRX | + PNX8XXX_UART_INT_ALLTX); + + /* + * Free the interrupt + */ + free_irq(sport->port.irq, sport); +} + +static void +pnx8xxx_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + unsigned long flags; + unsigned int lcr_fcr, old_ien, baud, quot; + unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8; + + /* + * We only support CS7 and CS8. + */ + while ((termios->c_cflag & CSIZE) != CS7 && + (termios->c_cflag & CSIZE) != CS8) { + termios->c_cflag &= ~CSIZE; + termios->c_cflag |= old_csize; + old_csize = CS8; + } + + if ((termios->c_cflag & CSIZE) == CS8) + lcr_fcr = PNX8XXX_UART_LCR_8BIT; + else + lcr_fcr = 0; + + if (termios->c_cflag & CSTOPB) + lcr_fcr |= PNX8XXX_UART_LCR_2STOPB; + if (termios->c_cflag & PARENB) { + lcr_fcr |= PNX8XXX_UART_LCR_PAREN; + if (!(termios->c_cflag & PARODD)) + lcr_fcr |= PNX8XXX_UART_LCR_PAREVN; + } + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); + quot = uart_get_divisor(port, baud); + + spin_lock_irqsave(&sport->port.lock, flags); + + sport->port.read_status_mask = ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN) | + ISTAT_TO_SM(PNX8XXX_UART_INT_EMPTY) | + ISTAT_TO_SM(PNX8XXX_UART_INT_RX); + if (termios->c_iflag & INPCK) + sport->port.read_status_mask |= + FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE) | + FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR); + if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK)) + sport->port.read_status_mask |= + ISTAT_TO_SM(PNX8XXX_UART_INT_BREAK); + + /* + * Characters to ignore + */ + sport->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + sport->port.ignore_status_mask |= + FIFO_TO_SM(PNX8XXX_UART_FIFO_RXFE) | + FIFO_TO_SM(PNX8XXX_UART_FIFO_RXPAR); + if (termios->c_iflag & IGNBRK) { + sport->port.ignore_status_mask |= + ISTAT_TO_SM(PNX8XXX_UART_INT_BREAK); + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + sport->port.ignore_status_mask |= + ISTAT_TO_SM(PNX8XXX_UART_INT_RXOVRN); + } + + /* + * ignore all characters if CREAD is not set + */ + if ((termios->c_cflag & CREAD) == 0) + sport->port.ignore_status_mask |= + ISTAT_TO_SM(PNX8XXX_UART_INT_RX); + + del_timer_sync(&sport->timer); + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + /* + * disable interrupts and drain transmitter + */ + old_ien = serial_in(sport, PNX8XXX_IEN); + serial_out(sport, PNX8XXX_IEN, old_ien & ~(PNX8XXX_UART_INT_ALLTX | + PNX8XXX_UART_INT_ALLRX)); + + while (serial_in(sport, PNX8XXX_FIFO) & PNX8XXX_UART_FIFO_TXFIFO_STA) + barrier(); + + /* then, disable everything */ + serial_out(sport, PNX8XXX_IEN, 0); + + /* Reset the Rx and Tx FIFOs too */ + lcr_fcr |= PNX8XXX_UART_LCR_TX_RST; + lcr_fcr |= PNX8XXX_UART_LCR_RX_RST; + + /* set the parity, stop bits and data size */ + serial_out(sport, PNX8XXX_LCR, lcr_fcr); + + /* set the baud rate */ + quot -= 1; + serial_out(sport, PNX8XXX_BAUD, quot); + + serial_out(sport, PNX8XXX_ICLR, -1); + + serial_out(sport, PNX8XXX_IEN, old_ien); + + if (UART_ENABLE_MS(&sport->port, termios->c_cflag)) + pnx8xxx_enable_ms(&sport->port); + + spin_unlock_irqrestore(&sport->port.lock, flags); +} + +static const char *pnx8xxx_type(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + + return sport->port.type == PORT_PNX8XXX ? "PNX8XXX" : NULL; +} + +/* + * Release the memory region(s) being used by 'port'. + */ +static void pnx8xxx_release_port(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + + release_mem_region(sport->port.mapbase, UART_PORT_SIZE); +} + +/* + * Request the memory region(s) being used by 'port'. + */ +static int pnx8xxx_request_port(struct uart_port *port) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + return request_mem_region(sport->port.mapbase, UART_PORT_SIZE, + "pnx8xxx-uart") != NULL ? 0 : -EBUSY; +} + +/* + * Configure/autoconfigure the port. + */ +static void pnx8xxx_config_port(struct uart_port *port, int flags) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + + if (flags & UART_CONFIG_TYPE && + pnx8xxx_request_port(&sport->port) == 0) + sport->port.type = PORT_PNX8XXX; +} + +/* + * Verify the new serial_struct (for TIOCSSERIAL). + * The only change we allow are to the flags and type, and + * even then only between PORT_PNX8XXX and PORT_UNKNOWN + */ +static int +pnx8xxx_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + int ret = 0; + + if (ser->type != PORT_UNKNOWN && ser->type != PORT_PNX8XXX) + ret = -EINVAL; + if (sport->port.irq != ser->irq) + ret = -EINVAL; + if (ser->io_type != SERIAL_IO_MEM) + ret = -EINVAL; + if (sport->port.uartclk / 16 != ser->baud_base) + ret = -EINVAL; + if ((void *)sport->port.mapbase != ser->iomem_base) + ret = -EINVAL; + if (sport->port.iobase != ser->port) + ret = -EINVAL; + if (ser->hub6 != 0) + ret = -EINVAL; + return ret; +} + +static const struct uart_ops pnx8xxx_pops = { + .tx_empty = pnx8xxx_tx_empty, + .set_mctrl = pnx8xxx_set_mctrl, + .get_mctrl = pnx8xxx_get_mctrl, + .stop_tx = pnx8xxx_stop_tx, + .start_tx = pnx8xxx_start_tx, + .stop_rx = pnx8xxx_stop_rx, + .enable_ms = pnx8xxx_enable_ms, + .break_ctl = pnx8xxx_break_ctl, + .startup = pnx8xxx_startup, + .shutdown = pnx8xxx_shutdown, + .set_termios = pnx8xxx_set_termios, + .type = pnx8xxx_type, + .release_port = pnx8xxx_release_port, + .request_port = pnx8xxx_request_port, + .config_port = pnx8xxx_config_port, + .verify_port = pnx8xxx_verify_port, +}; + + +/* + * Setup the PNX8XXX serial ports. + * + * Note also that we support "console=ttySx" where "x" is either 0 or 1. + */ +static void __init pnx8xxx_init_ports(void) +{ + static int first = 1; + int i; + + if (!first) + return; + first = 0; + + for (i = 0; i < NR_PORTS; i++) { + timer_setup(&pnx8xxx_ports[i].timer, pnx8xxx_timeout, 0); + pnx8xxx_ports[i].port.ops = &pnx8xxx_pops; + } +} + +#ifdef CONFIG_SERIAL_PNX8XXX_CONSOLE + +static void pnx8xxx_console_putchar(struct uart_port *port, int ch) +{ + struct pnx8xxx_port *sport = + container_of(port, struct pnx8xxx_port, port); + int status; + + do { + /* Wait for UART_TX register to empty */ + status = serial_in(sport, PNX8XXX_FIFO); + } while (status & PNX8XXX_UART_FIFO_TXFIFO); + serial_out(sport, PNX8XXX_FIFO, ch); +} + +/* + * Interrupts are disabled on entering + */static void +pnx8xxx_console_write(struct console *co, const char *s, unsigned int count) +{ + struct pnx8xxx_port *sport = &pnx8xxx_ports[co->index]; + unsigned int old_ien, status; + + /* + * First, save IEN and then disable interrupts + */ + old_ien = serial_in(sport, PNX8XXX_IEN); + serial_out(sport, PNX8XXX_IEN, old_ien & ~(PNX8XXX_UART_INT_ALLTX | + PNX8XXX_UART_INT_ALLRX)); + + uart_console_write(&sport->port, s, count, pnx8xxx_console_putchar); + + /* + * Finally, wait for transmitter to become empty + * and restore IEN + */ + do { + /* Wait for UART_TX register to empty */ + status = serial_in(sport, PNX8XXX_FIFO); + } while (status & PNX8XXX_UART_FIFO_TXFIFO); + + /* Clear TX and EMPTY interrupt */ + serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_TX | + PNX8XXX_UART_INT_EMPTY); + + serial_out(sport, PNX8XXX_IEN, old_ien); +} + +static int __init +pnx8xxx_console_setup(struct console *co, char *options) +{ + struct pnx8xxx_port *sport; + int baud = 38400; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + /* + * Check whether an invalid uart number has been specified, and + * if so, search for the first available port that does have + * console support. + */ + if (co->index == -1 || co->index >= NR_PORTS) + co->index = 0; + sport = &pnx8xxx_ports[co->index]; + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + + return uart_set_options(&sport->port, co, baud, parity, bits, flow); +} + +static struct uart_driver pnx8xxx_reg; +static struct console pnx8xxx_console = { + .name = "ttyS", + .write = pnx8xxx_console_write, + .device = uart_console_device, + .setup = pnx8xxx_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &pnx8xxx_reg, +}; + +static int __init pnx8xxx_rs_console_init(void) +{ + pnx8xxx_init_ports(); + register_console(&pnx8xxx_console); + return 0; +} +console_initcall(pnx8xxx_rs_console_init); + +#define PNX8XXX_CONSOLE &pnx8xxx_console +#else +#define PNX8XXX_CONSOLE NULL +#endif + +static struct uart_driver pnx8xxx_reg = { + .owner = THIS_MODULE, + .driver_name = "ttyS", + .dev_name = "ttyS", + .major = SERIAL_PNX8XXX_MAJOR, + .minor = MINOR_START, + .nr = NR_PORTS, + .cons = PNX8XXX_CONSOLE, +}; + +static int pnx8xxx_serial_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct pnx8xxx_port *sport = platform_get_drvdata(pdev); + + return uart_suspend_port(&pnx8xxx_reg, &sport->port); +} + +static int pnx8xxx_serial_resume(struct platform_device *pdev) +{ + struct pnx8xxx_port *sport = platform_get_drvdata(pdev); + + return uart_resume_port(&pnx8xxx_reg, &sport->port); +} + +static int pnx8xxx_serial_probe(struct platform_device *pdev) +{ + struct resource *res = pdev->resource; + int i; + + for (i = 0; i < pdev->num_resources; i++, res++) { + if (!(res->flags & IORESOURCE_MEM)) + continue; + + for (i = 0; i < NR_PORTS; i++) { + if (pnx8xxx_ports[i].port.mapbase != res->start) + continue; + + pnx8xxx_ports[i].port.dev = &pdev->dev; + uart_add_one_port(&pnx8xxx_reg, &pnx8xxx_ports[i].port); + platform_set_drvdata(pdev, &pnx8xxx_ports[i]); + break; + } + } + + return 0; +} + +static int pnx8xxx_serial_remove(struct platform_device *pdev) +{ + struct pnx8xxx_port *sport = platform_get_drvdata(pdev); + + if (sport) + uart_remove_one_port(&pnx8xxx_reg, &sport->port); + + return 0; +} + +static struct platform_driver pnx8xxx_serial_driver = { + .driver = { + .name = "pnx8xxx-uart", + }, + .probe = pnx8xxx_serial_probe, + .remove = pnx8xxx_serial_remove, + .suspend = pnx8xxx_serial_suspend, + .resume = pnx8xxx_serial_resume, +}; + +static int __init pnx8xxx_serial_init(void) +{ + int ret; + + printk(KERN_INFO "Serial: PNX8XXX driver\n"); + + pnx8xxx_init_ports(); + + ret = uart_register_driver(&pnx8xxx_reg); + if (ret == 0) { + ret = platform_driver_register(&pnx8xxx_serial_driver); + if (ret) + uart_unregister_driver(&pnx8xxx_reg); + } + return ret; +} + +static void __exit pnx8xxx_serial_exit(void) +{ + platform_driver_unregister(&pnx8xxx_serial_driver); + uart_unregister_driver(&pnx8xxx_reg); +} + +module_init(pnx8xxx_serial_init); +module_exit(pnx8xxx_serial_exit); + +MODULE_AUTHOR("Embedded Alley Solutions, Inc."); +MODULE_DESCRIPTION("PNX8XXX SoCs serial port driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_PNX8XXX_MAJOR); +MODULE_ALIAS("platform:pnx8xxx-uart"); |