diff options
Diffstat (limited to 'drivers/usb/serial/io_usbvend.h')
| -rw-r--r-- | drivers/usb/serial/io_usbvend.h | 681 |
1 files changed, 681 insertions, 0 deletions
diff --git a/drivers/usb/serial/io_usbvend.h b/drivers/usb/serial/io_usbvend.h new file mode 100644 index 000000000..7ca5ca49a --- /dev/null +++ b/drivers/usb/serial/io_usbvend.h @@ -0,0 +1,681 @@ +// SPDX-License-Identifier: GPL-2.0+ +/************************************************************************ + * + * USBVEND.H Vendor-specific USB definitions + * + * NOTE: This must be kept in sync with the Edgeport firmware and + * must be kept backward-compatible with older firmware. + * + ************************************************************************ + * + * Copyright (C) 1998 Inside Out Networks, Inc. + * + ************************************************************************/ + +#if !defined(_USBVEND_H) +#define _USBVEND_H + +/************************************************************************ + * + * D e f i n e s / T y p e d e f s + * + ************************************************************************/ + +// +// Definitions of USB product IDs +// + +#define USB_VENDOR_ID_ION 0x1608 // Our VID +#define USB_VENDOR_ID_TI 0x0451 // TI VID +#define USB_VENDOR_ID_AXIOHM 0x05D9 /* Axiohm VID */ + +// +// Definitions of USB product IDs (PID) +// We break the USB-defined PID into an OEM Id field (upper 6 bits) +// and a Device Id (bottom 10 bits). The Device Id defines what +// device this actually is regardless of what the OEM wants to +// call it. +// + +// ION-device OEM IDs +#define ION_OEM_ID_ION 0 // 00h Inside Out Networks +#define ION_OEM_ID_NLYNX 1 // 01h NLynx Systems +#define ION_OEM_ID_GENERIC 2 // 02h Generic OEM +#define ION_OEM_ID_MAC 3 // 03h Mac Version +#define ION_OEM_ID_MEGAWOLF 4 // 04h Lupusb OEM Mac version (MegaWolf) +#define ION_OEM_ID_MULTITECH 5 // 05h Multitech Rapidports +#define ION_OEM_ID_AGILENT 6 // 06h AGILENT board + + +// ION-device Device IDs +// Product IDs - assigned to match middle digit of serial number (No longer true) + +#define ION_DEVICE_ID_80251_NETCHIP 0x020 // This bit is set in the PID if this edgeport hardware$ + // is based on the 80251+Netchip. + +#define ION_DEVICE_ID_GENERATION_1 0x00 // Value for 930 based edgeports +#define ION_DEVICE_ID_GENERATION_2 0x01 // Value for 80251+Netchip. +#define ION_DEVICE_ID_GENERATION_3 0x02 // Value for Texas Instruments TUSB5052 chip +#define ION_DEVICE_ID_GENERATION_4 0x03 // Watchport Family of products +#define ION_GENERATION_MASK 0x03 + +#define ION_DEVICE_ID_HUB_MASK 0x0080 // This bit in the PID designates a HUB device + // for example 8C would be a 421 4 port hub + // and 8D would be a 2 port embedded hub + +#define EDGEPORT_DEVICE_ID_MASK 0x0ff // Not including OEM or GENERATION fields + +#define ION_DEVICE_ID_UNCONFIGURED_EDGE_DEVICE 0x000 // In manufacturing only +#define ION_DEVICE_ID_EDGEPORT_4 0x001 // Edgeport/4 RS232 +#define ION_DEVICE_ID_EDGEPORT_8R 0x002 // Edgeport with RJ45 no Ring +#define ION_DEVICE_ID_RAPIDPORT_4 0x003 // Rapidport/4 +#define ION_DEVICE_ID_EDGEPORT_4T 0x004 // Edgeport/4 RS232 for Telxon (aka "Fleetport") +#define ION_DEVICE_ID_EDGEPORT_2 0x005 // Edgeport/2 RS232 +#define ION_DEVICE_ID_EDGEPORT_4I 0x006 // Edgeport/4 RS422 +#define ION_DEVICE_ID_EDGEPORT_2I 0x007 // Edgeport/2 RS422/RS485 +#define ION_DEVICE_ID_EDGEPORT_8RR 0x008 // Edgeport with RJ45 with Data and RTS/CTS only +// ION_DEVICE_ID_EDGEPORT_8_HANDBUILT 0x009 // Hand-built Edgeport/8 (Placeholder, used in middle digit of serial number only!) +// ION_DEVICE_ID_MULTIMODEM_4X56 0x00A // MultiTech version of RP/4 (Placeholder, used in middle digit of serial number only!) +#define ION_DEVICE_ID_EDGEPORT_PARALLEL_PORT 0x00B // Edgeport/(4)21 Parallel port (USS720) +#define ION_DEVICE_ID_EDGEPORT_421 0x00C // Edgeport/421 Hub+RS232+Parallel +#define ION_DEVICE_ID_EDGEPORT_21 0x00D // Edgeport/21 RS232+Parallel +#define ION_DEVICE_ID_EDGEPORT_8_DUAL_CPU 0x00E // Half of an Edgeport/8 (the kind with 2 EP/4s on 1 PCB) +#define ION_DEVICE_ID_EDGEPORT_8 0x00F // Edgeport/8 (single-CPU) +#define ION_DEVICE_ID_EDGEPORT_2_DIN 0x010 // Edgeport/2 RS232 with Apple DIN connector +#define ION_DEVICE_ID_EDGEPORT_4_DIN 0x011 // Edgeport/4 RS232 with Apple DIN connector +#define ION_DEVICE_ID_EDGEPORT_16_DUAL_CPU 0x012 // Half of an Edgeport/16 (the kind with 2 EP/8s) +#define ION_DEVICE_ID_EDGEPORT_COMPATIBLE 0x013 // Edgeport Compatible, for NCR, Axiohm etc. testing +#define ION_DEVICE_ID_EDGEPORT_8I 0x014 // Edgeport/8 RS422 (single-CPU) +#define ION_DEVICE_ID_EDGEPORT_1 0x015 // Edgeport/1 RS232 +#define ION_DEVICE_ID_EPOS44 0x016 // Half of an EPOS/44 (TIUMP BASED) +#define ION_DEVICE_ID_EDGEPORT_42 0x017 // Edgeport/42 +#define ION_DEVICE_ID_EDGEPORT_412_8 0x018 // Edgeport/412 8 port part +#define ION_DEVICE_ID_EDGEPORT_412_4 0x019 // Edgeport/412 4 port part +#define ION_DEVICE_ID_EDGEPORT_22I 0x01A // Edgeport/22I is an Edgeport/4 with ports 1&2 RS422 and ports 3&4 RS232 + +// Compact Form factor TI based devices 2c, 21c, 22c, 221c +#define ION_DEVICE_ID_EDGEPORT_2C 0x01B // Edgeport/2c is a TI based Edgeport/2 - Small I2c +#define ION_DEVICE_ID_EDGEPORT_221C 0x01C // Edgeport/221c is a TI based Edgeport/2 with lucent chip and + // 2 external hub ports - Large I2C +#define ION_DEVICE_ID_EDGEPORT_22C 0x01D // Edgeport/22c is a TI based Edgeport/2 with + // 2 external hub ports - Large I2C +#define ION_DEVICE_ID_EDGEPORT_21C 0x01E // Edgeport/21c is a TI based Edgeport/2 with lucent chip + // Small I2C + + +/* + * DANGER DANGER The 0x20 bit was used to indicate a 8251/netchip GEN 2 device. + * Since the MAC, Linux, and Optimal drivers still used the old code + * I suggest that you skip the 0x20 bit when creating new PIDs + */ + + +// Generation 3 devices -- 3410 based edgport/1 (256 byte I2C) +#define ION_DEVICE_ID_TI3410_EDGEPORT_1 0x040 // Edgeport/1 RS232 +#define ION_DEVICE_ID_TI3410_EDGEPORT_1I 0x041 // Edgeport/1i- RS422 model + +// Ti based software switchable RS232/RS422/RS485 devices +#define ION_DEVICE_ID_EDGEPORT_4S 0x042 // Edgeport/4s - software switchable model +#define ION_DEVICE_ID_EDGEPORT_8S 0x043 // Edgeport/8s - software switchable model + +// Usb to Ethernet dongle +#define ION_DEVICE_ID_EDGEPORT_E 0x0E0 // Edgeport/E Usb to Ethernet + +// Edgeport TI based devices +#define ION_DEVICE_ID_TI_EDGEPORT_4 0x0201 // Edgeport/4 RS232 +#define ION_DEVICE_ID_TI_EDGEPORT_2 0x0205 // Edgeport/2 RS232 +#define ION_DEVICE_ID_TI_EDGEPORT_4I 0x0206 // Edgeport/4i RS422 +#define ION_DEVICE_ID_TI_EDGEPORT_2I 0x0207 // Edgeport/2i RS422/RS485 +#define ION_DEVICE_ID_TI_EDGEPORT_421 0x020C // Edgeport/421 4 hub 2 RS232 + Parallel (lucent on a different hub port) +#define ION_DEVICE_ID_TI_EDGEPORT_21 0x020D // Edgeport/21 2 RS232 + Parallel (lucent on a different hub port) +#define ION_DEVICE_ID_TI_EDGEPORT_416 0x0212 // Edgeport/416 +#define ION_DEVICE_ID_TI_EDGEPORT_1 0x0215 // Edgeport/1 RS232 +#define ION_DEVICE_ID_TI_EDGEPORT_42 0x0217 // Edgeport/42 4 hub 2 RS232 +#define ION_DEVICE_ID_TI_EDGEPORT_22I 0x021A // Edgeport/22I is an Edgeport/4 with ports 1&2 RS422 and ports 3&4 RS232 +#define ION_DEVICE_ID_TI_EDGEPORT_2C 0x021B // Edgeport/2c RS232 +#define ION_DEVICE_ID_TI_EDGEPORT_221C 0x021C // Edgeport/221c is a TI based Edgeport/2 with lucent chip and + // 2 external hub ports - Large I2C +#define ION_DEVICE_ID_TI_EDGEPORT_22C 0x021D // Edgeport/22c is a TI based Edgeport/2 with + // 2 external hub ports - Large I2C +#define ION_DEVICE_ID_TI_EDGEPORT_21C 0x021E // Edgeport/21c is a TI based Edgeport/2 with lucent chip + +// Generation 3 devices -- 3410 based edgport/1 (256 byte I2C) +#define ION_DEVICE_ID_TI_TI3410_EDGEPORT_1 0x0240 // Edgeport/1 RS232 +#define ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I 0x0241 // Edgeport/1i- RS422 model + +// Ti based software switchable RS232/RS422/RS485 devices +#define ION_DEVICE_ID_TI_EDGEPORT_4S 0x0242 // Edgeport/4s - software switchable model +#define ION_DEVICE_ID_TI_EDGEPORT_8S 0x0243 // Edgeport/8s - software switchable model +#define ION_DEVICE_ID_TI_EDGEPORT_8 0x0244 // Edgeport/8 (single-CPU) +#define ION_DEVICE_ID_TI_EDGEPORT_416B 0x0247 // Edgeport/416 + + +/************************************************************************ + * + * Generation 4 devices + * + ************************************************************************/ + +// Watchport based on 3410 both 1-wire and binary products (16K I2C) +#define ION_DEVICE_ID_WP_UNSERIALIZED 0x300 // Watchport based on 3410 both 1-wire and binary products +#define ION_DEVICE_ID_WP_PROXIMITY 0x301 // Watchport/P Discontinued +#define ION_DEVICE_ID_WP_MOTION 0x302 // Watchport/M +#define ION_DEVICE_ID_WP_MOISTURE 0x303 // Watchport/W +#define ION_DEVICE_ID_WP_TEMPERATURE 0x304 // Watchport/T +#define ION_DEVICE_ID_WP_HUMIDITY 0x305 // Watchport/H + +#define ION_DEVICE_ID_WP_POWER 0x306 // Watchport +#define ION_DEVICE_ID_WP_LIGHT 0x307 // Watchport +#define ION_DEVICE_ID_WP_RADIATION 0x308 // Watchport +#define ION_DEVICE_ID_WP_ACCELERATION 0x309 // Watchport/A +#define ION_DEVICE_ID_WP_DISTANCE 0x30A // Watchport/D Discontinued +#define ION_DEVICE_ID_WP_PROX_DIST 0x30B // Watchport/D uses distance sensor + // Default to /P function + +#define ION_DEVICE_ID_PLUS_PWR_HP4CD 0x30C // 5052 Plus Power HubPort/4CD+ (for Dell) +#define ION_DEVICE_ID_PLUS_PWR_HP4C 0x30D // 5052 Plus Power HubPort/4C+ +#define ION_DEVICE_ID_PLUS_PWR_PCI 0x30E // 3410 Plus Power PCI Host Controller 4 port + + +// +// Definitions for AXIOHM USB product IDs +// +#define USB_VENDOR_ID_AXIOHM 0x05D9 // Axiohm VID + +#define AXIOHM_DEVICE_ID_MASK 0xffff +#define AXIOHM_DEVICE_ID_EPIC_A758 0xA758 +#define AXIOHM_DEVICE_ID_EPIC_A794 0xA794 +#define AXIOHM_DEVICE_ID_EPIC_A225 0xA225 + + +// +// Definitions for NCR USB product IDs +// +#define USB_VENDOR_ID_NCR 0x0404 // NCR VID + +#define NCR_DEVICE_ID_MASK 0xffff +#define NCR_DEVICE_ID_EPIC_0202 0x0202 +#define NCR_DEVICE_ID_EPIC_0203 0x0203 +#define NCR_DEVICE_ID_EPIC_0310 0x0310 +#define NCR_DEVICE_ID_EPIC_0311 0x0311 +#define NCR_DEVICE_ID_EPIC_0312 0x0312 + + +// +// Definitions for SYMBOL USB product IDs +// +#define USB_VENDOR_ID_SYMBOL 0x05E0 // Symbol VID +#define SYMBOL_DEVICE_ID_MASK 0xffff +#define SYMBOL_DEVICE_ID_KEYFOB 0x0700 + + +// +// Definitions for other product IDs +#define ION_DEVICE_ID_MT4X56USB 0x1403 // OEM device +#define ION_DEVICE_ID_E5805A 0x1A01 // OEM device (rebranded Edgeport/4) + + +#define GENERATION_ID_FROM_USB_PRODUCT_ID(ProductId) \ + ((__u16) ((ProductId >> 8) & (ION_GENERATION_MASK))) + +#define MAKE_USB_PRODUCT_ID(OemId, DeviceId) \ + ((__u16) (((OemId) << 10) || (DeviceId))) + +#define DEVICE_ID_FROM_USB_PRODUCT_ID(ProductId) \ + ((__u16) ((ProductId) & (EDGEPORT_DEVICE_ID_MASK))) + +#define OEM_ID_FROM_USB_PRODUCT_ID(ProductId) \ + ((__u16) (((ProductId) >> 10) & 0x3F)) + +// +// Definitions of parameters for download code. Note that these are +// specific to a given version of download code and must change if the +// corresponding download code changes. +// + +// TxCredits value below which driver won't bother sending (to prevent too many small writes). +// Send only if above 25% +#define EDGE_FW_GET_TX_CREDITS_SEND_THRESHOLD(InitialCredit, MaxPacketSize) (max(((InitialCredit) / 4), (MaxPacketSize))) + +#define EDGE_FW_BULK_MAX_PACKET_SIZE 64 // Max Packet Size for Bulk In Endpoint (EP1) +#define EDGE_FW_BULK_READ_BUFFER_SIZE 1024 // Size to use for Bulk reads + +#define EDGE_FW_INT_MAX_PACKET_SIZE 32 // Max Packet Size for Interrupt In Endpoint + // Note that many units were shipped with MPS=16, we + // force an upgrade to this value). +#define EDGE_FW_INT_INTERVAL 2 // 2ms polling on IntPipe + + +// +// Definitions of I/O Networks vendor-specific requests +// for default endpoint +// +// bmRequestType = 01000000 Set vendor-specific, to device +// bmRequestType = 11000000 Get vendor-specific, to device +// +// These are the definitions for the bRequest field for the +// above bmRequestTypes. +// +// For the read/write Edgeport memory commands, the parameters +// are as follows: +// wValue = 16-bit address +// wIndex = unused (though we could put segment 00: or FF: here) +// wLength = # bytes to read/write (max 64) +// + +#define USB_REQUEST_ION_RESET_DEVICE 0 // Warm reboot Edgeport, retaining USB address +#define USB_REQUEST_ION_GET_EPIC_DESC 1 // Get Edgeport Compatibility Descriptor +// unused 2 // Unused, available +#define USB_REQUEST_ION_READ_RAM 3 // Read EdgePort RAM at specified addr +#define USB_REQUEST_ION_WRITE_RAM 4 // Write EdgePort RAM at specified addr +#define USB_REQUEST_ION_READ_ROM 5 // Read EdgePort ROM at specified addr +#define USB_REQUEST_ION_WRITE_ROM 6 // Write EdgePort ROM at specified addr +#define USB_REQUEST_ION_EXEC_DL_CODE 7 // Begin execution of RAM-based download + // code by jumping to address in wIndex:wValue +// 8 // Unused, available +#define USB_REQUEST_ION_ENABLE_SUSPEND 9 // Enable/Disable suspend feature + // (wValue != 0: Enable; wValue = 0: Disable) + +#define USB_REQUEST_ION_SEND_IOSP 10 // Send an IOSP command to the edgeport over the control pipe +#define USB_REQUEST_ION_RECV_IOSP 11 // Receive an IOSP command from the edgeport over the control pipe + + +#define USB_REQUEST_ION_DIS_INT_TIMER 0x80 // Sent to Axiohm to enable/ disable + // interrupt token timer + // wValue = 1, enable (default) + // wValue = 0, disable + +// +// Define parameter values for our vendor-specific commands +// + +// +// Edgeport Compatibility Descriptor +// +// This descriptor is only returned by Edgeport-compatible devices +// supporting the EPiC spec. True ION devices do not return this +// descriptor, but instead return STALL on receipt of the +// GET_EPIC_DESC command. The driver interprets a STALL to mean that +// this is a "real" Edgeport. +// + +struct edge_compatibility_bits { + // This __u32 defines which Vendor-specific commands/functionality + // the device supports on the default EP0 pipe. + + __u32 VendEnableSuspend : 1; // 0001 Set if device supports ION_ENABLE_SUSPEND + __u32 VendUnused : 31; // Available for future expansion, must be 0 + + // This __u32 defines which IOSP commands are supported over the + // bulk pipe EP1. + + // xxxx Set if device supports: + __u32 IOSPOpen : 1; // 0001 OPEN / OPEN_RSP (Currently must be 1) + __u32 IOSPClose : 1; // 0002 CLOSE + __u32 IOSPChase : 1; // 0004 CHASE / CHASE_RSP + __u32 IOSPSetRxFlow : 1; // 0008 SET_RX_FLOW + __u32 IOSPSetTxFlow : 1; // 0010 SET_TX_FLOW + __u32 IOSPSetXChar : 1; // 0020 SET_XON_CHAR/SET_XOFF_CHAR + __u32 IOSPRxCheck : 1; // 0040 RX_CHECK_REQ/RX_CHECK_RSP + __u32 IOSPSetClrBreak : 1; // 0080 SET_BREAK/CLEAR_BREAK + __u32 IOSPWriteMCR : 1; // 0100 MCR register writes (set/clr DTR/RTS) + __u32 IOSPWriteLCR : 1; // 0200 LCR register writes (wordlen/stop/parity) + __u32 IOSPSetBaudRate : 1; // 0400 setting Baud rate (writes to LCR.80h and DLL/DLM register) + __u32 IOSPDisableIntPipe : 1; // 0800 Do not use the interrupt pipe for TxCredits or RxButesAvailable + __u32 IOSPRxDataAvail : 1; // 1000 Return status of RX Fifo (Data available in Fifo) + __u32 IOSPTxPurge : 1; // 2000 Purge TXBuffer and/or Fifo in Edgeport hardware + __u32 IOSPUnused : 18; // Available for future expansion, must be 0 + + // This __u32 defines which 'general' features are supported + + __u32 TrueEdgeport : 1; // 0001 Set if device is a 'real' Edgeport + // (Used only by driver, NEVER set by an EPiC device) + __u32 GenUnused : 31; // Available for future expansion, must be 0 +}; + +#define EDGE_COMPATIBILITY_MASK0 0x0001 +#define EDGE_COMPATIBILITY_MASK1 0x3FFF +#define EDGE_COMPATIBILITY_MASK2 0x0001 + +struct edge_compatibility_descriptor { + __u8 Length; // Descriptor Length (per USB spec) + __u8 DescType; // Descriptor Type (per USB spec, =DEVICE type) + __u8 EpicVer; // Version of EPiC spec supported + // (Currently must be 1) + __u8 NumPorts; // Number of serial ports supported + __u8 iDownloadFile; // Index of string containing download code filename + // 0=no download, FF=download compiled into driver. + __u8 Unused[3]; // Available for future expansion, must be 0 + // (Currently must be 0). + __u8 MajorVersion; // Firmware version: xx. + __u8 MinorVersion; // yy. + __le16 BuildNumber; // zzzz (LE format) + + // The following structure contains __u32s, with each bit + // specifying whether the EPiC device supports the given + // command or functionality. + struct edge_compatibility_bits Supports; +}; + +// Values for iDownloadFile +#define EDGE_DOWNLOAD_FILE_NONE 0 // No download requested +#define EDGE_DOWNLOAD_FILE_INTERNAL 0xFF // Download the file compiled into driver (930 version) +#define EDGE_DOWNLOAD_FILE_I930 0xFF // Download the file compiled into driver (930 version) +#define EDGE_DOWNLOAD_FILE_80251 0xFE // Download the file compiled into driver (80251 version) + + + +/* + * Special addresses for READ/WRITE_RAM/ROM + */ + +// Version 1 (original) format of DeviceParams +#define EDGE_MANUF_DESC_ADDR_V1 0x00FF7F00 +#define EDGE_MANUF_DESC_LEN_V1 sizeof(EDGE_MANUF_DESCRIPTOR_V1) + +// Version 2 format of DeviceParams. This format is longer (3C0h) +// and starts lower in memory, at the uppermost 1K in ROM. +#define EDGE_MANUF_DESC_ADDR 0x00FF7C00 +#define EDGE_MANUF_DESC_LEN sizeof(struct edge_manuf_descriptor) + +// Boot params descriptor +#define EDGE_BOOT_DESC_ADDR 0x00FF7FC0 +#define EDGE_BOOT_DESC_LEN sizeof(struct edge_boot_descriptor) + +// Define the max block size that may be read or written +// in a read/write RAM/ROM command. +#define MAX_SIZE_REQ_ION_READ_MEM ((__u16)64) +#define MAX_SIZE_REQ_ION_WRITE_MEM ((__u16)64) + + +// +// Notes for the following two ION vendor-specific param descriptors: +// +// 1. These have a standard USB descriptor header so they look like a +// normal descriptor. +// 2. Any strings in the structures are in USB-defined string +// descriptor format, so that they may be separately retrieved, +// if necessary, with a minimum of work on the 930. This also +// requires them to be in UNICODE format, which, for English at +// least, simply means extending each __u8 into a __u16. +// 3. For all fields, 00 means 'uninitialized'. +// 4. All unused areas should be set to 00 for future expansion. +// + +// This structure is ver 2 format. It contains ALL USB descriptors as +// well as the configuration parameters that were in the original V1 +// structure. It is NOT modified when new boot code is downloaded; rather, +// these values are set or modified by manufacturing. It is located at +// xC00-xFBF (length 3C0h) in the ROM. +// This structure is a superset of the v1 structure and is arranged so +// that all of the v1 fields remain at the same address. We are just +// adding more room to the front of the structure to hold the descriptors. +// +// The actual contents of this structure are defined in a 930 assembly +// file, converted to a binary image, and then written by the serialization +// program. The C definition of this structure just defines a dummy +// area for general USB descriptors and the descriptor tables (the root +// descriptor starts at xC00). At the bottom of the structure are the +// fields inherited from the v1 structure. + +#define MAX_SERIALNUMBER_LEN 12 +#define MAX_ASSEMBLYNUMBER_LEN 14 + +struct edge_manuf_descriptor { + + __u16 RootDescTable[0x10]; // C00 Root of descriptor tables (just a placeholder) + __u8 DescriptorArea[0x2E0]; // C20 Descriptors go here, up to 2E0h (just a placeholder) + + // Start of v1-compatible section + __u8 Length; // F00 Desc length for what follows, per USB (= C0h ) + __u8 DescType; // F01 Desc type, per USB (=DEVICE type) + __u8 DescVer; // F02 Desc version/format (currently 2) + __u8 NumRootDescEntries; // F03 # entries in RootDescTable + + __u8 RomSize; // F04 Size of ROM/E2PROM in K + __u8 RamSize; // F05 Size of external RAM in K + __u8 CpuRev; // F06 CPU revision level (chg only if s/w visible) + __u8 BoardRev; // F07 PCB revision level (chg only if s/w visible) + + __u8 NumPorts; // F08 Number of ports + __u8 DescDate[3]; // F09 MM/DD/YY when descriptor template was compiler, + // so host can track changes to USB-only descriptors. + + __u8 SerNumLength; // F0C USB string descriptor len + __u8 SerNumDescType; // F0D USB descriptor type (=STRING type) + __le16 SerialNumber[MAX_SERIALNUMBER_LEN]; // F0E "01-01-000100" Unicode Serial Number + + __u8 AssemblyNumLength; // F26 USB string descriptor len + __u8 AssemblyNumDescType; // F27 USB descriptor type (=STRING type) + __le16 AssemblyNumber[MAX_ASSEMBLYNUMBER_LEN]; // F28 "350-1000-01-A " assembly number + + __u8 OemAssyNumLength; // F44 USB string descriptor len + __u8 OemAssyNumDescType; // F45 USB descriptor type (=STRING type) + __le16 OemAssyNumber[MAX_ASSEMBLYNUMBER_LEN]; // F46 "xxxxxxxxxxxxxx" OEM assembly number + + __u8 ManufDateLength; // F62 USB string descriptor len + __u8 ManufDateDescType; // F63 USB descriptor type (=STRING type) + __le16 ManufDate[6]; // F64 "MMDDYY" manufacturing date + + __u8 Reserved3[0x4D]; // F70 -- unused, set to 0 -- + + __u8 UartType; // FBD Uart Type + __u8 IonPid; // FBE Product ID, == LSB of USB DevDesc.PID + // (Note: Edgeport/4s before 11/98 will have + // 00 here instead of 01) + __u8 IonConfig; // FBF Config byte for ION manufacturing use + // FBF end of structure, total len = 3C0h + +}; + + +#define MANUF_DESC_VER_1 1 // Original definition of MANUF_DESC +#define MANUF_DESC_VER_2 2 // Ver 2, starts at xC00h len 3C0h + + +// Uart Types +// Note: Since this field was added only recently, all Edgeport/4 units +// shipped before 11/98 will have 00 in this field. Therefore, +// both 00 and 01 values mean '654. +#define MANUF_UART_EXAR_654_EARLY 0 // Exar 16C654 in Edgeport/4s before 11/98 +#define MANUF_UART_EXAR_654 1 // Exar 16C654 +#define MANUF_UART_EXAR_2852 2 // Exar 16C2852 + +// +// Note: The CpuRev and BoardRev values do not conform to manufacturing +// revisions; they are to be incremented only when the CPU or hardware +// changes in a software-visible way, such that the 930 software or +// the host driver needs to handle the hardware differently. +// + +// Values of bottom 5 bits of CpuRev & BoardRev for +// Implementation 0 (ie, 930-based) +#define MANUF_CPU_REV_AD4 1 // 930 AD4, with EP1 Rx bug (needs RXSPM) +#define MANUF_CPU_REV_AD5 2 // 930 AD5, with above bug (supposedly) fixed +#define MANUF_CPU_80251 0x20 // Intel 80251 + + +#define MANUF_BOARD_REV_A 1 // Original version, == Manuf Rev A +#define MANUF_BOARD_REV_B 2 // Manuf Rev B, wakeup interrupt works +#define MANUF_BOARD_REV_C 3 // Manuf Rev C, 2/4 ports, rs232/rs422 +#define MANUF_BOARD_REV_GENERATION_2 0x20 // Second generaiton edgeport + + +// Values of bottom 5 bits of CpuRev & BoardRev for +// Implementation 1 (ie, 251+Netchip-based) +#define MANUF_CPU_REV_1 1 // C251TB Rev 1 (Need actual Intel rev here) + +#define MANUF_BOARD_REV_A 1 // First rev of 251+Netchip design + +#define MANUF_SERNUM_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->SerialNumber) +#define MANUF_ASSYNUM_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->AssemblyNumber) +#define MANUF_OEMASSYNUM_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->OemAssyNumber) +#define MANUF_MANUFDATE_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->ManufDate) + +#define MANUF_ION_CONFIG_DIAG_NO_LOOP 0x20 // As below but no ext loopback test +#define MANUF_ION_CONFIG_DIAG 0x40 // 930 based device: 1=Run h/w diags, 0=norm + // TIUMP Device : 1=IONSERIAL needs to run Final Test +#define MANUF_ION_CONFIG_MASTER 0x80 // 930 based device: 1=Master mode, 0=Normal + // TIUMP Device : 1=First device on a multi TIUMP Device + +// +// This structure describes parameters for the boot code, and +// is programmed along with new boot code. These are values +// which are specific to a given build of the boot code. It +// is exactly 64 bytes long and is fixed at address FF:xFC0 +// - FF:xFFF. Note that the 930-mandated UCONFIG bytes are +// included in this structure. +// +struct edge_boot_descriptor { + __u8 Length; // C0 Desc length, per USB (= 40h) + __u8 DescType; // C1 Desc type, per USB (= DEVICE type) + __u8 DescVer; // C2 Desc version/format + __u8 Reserved1; // C3 -- unused, set to 0 -- + + __le16 BootCodeLength; // C4 Boot code goes from FF:0000 to FF:(len-1) + // (LE format) + + __u8 MajorVersion; // C6 Firmware version: xx. + __u8 MinorVersion; // C7 yy. + __le16 BuildNumber; // C8 zzzz (LE format) + + __u16 EnumRootDescTable; // CA Root of ROM-based descriptor table + __u8 NumDescTypes; // CC Number of supported descriptor types + + __u8 Reserved4; // CD Fix Compiler Packing + + __le16 Capabilities; // CE-CF Capabilities flags (LE format) + __u8 Reserved2[0x28]; // D0 -- unused, set to 0 -- + __u8 UConfig0; // F8 930-defined CPU configuration byte 0 + __u8 UConfig1; // F9 930-defined CPU configuration byte 1 + __u8 Reserved3[6]; // FA -- unused, set to 0 -- + // FF end of structure, total len = 80 +}; + + +#define BOOT_DESC_VER_1 1 // Original definition of BOOT_PARAMS +#define BOOT_DESC_VER_2 2 // 2nd definition, descriptors not included in boot + + + // Capabilities flags + +#define BOOT_CAP_RESET_CMD 0x0001 // If set, boot correctly supports ION_RESET_DEVICE + + +/************************************************************************ + T I U M P D E F I N I T I O N S + ***********************************************************************/ + +// Chip definitions in I2C +#define UMP5152 0x52 +#define UMP3410 0x10 + + +//************************************************************************ +// TI I2C Format Definitions +//************************************************************************ +#define I2C_DESC_TYPE_INFO_BASIC 0x01 +#define I2C_DESC_TYPE_FIRMWARE_BASIC 0x02 +#define I2C_DESC_TYPE_DEVICE 0x03 +#define I2C_DESC_TYPE_CONFIG 0x04 +#define I2C_DESC_TYPE_STRING 0x05 +#define I2C_DESC_TYPE_FIRMWARE_AUTO 0x07 // for 3410 download +#define I2C_DESC_TYPE_CONFIG_KLUDGE 0x14 // for 3410 +#define I2C_DESC_TYPE_WATCHPORT_VERSION 0x15 // firmware version number for watchport +#define I2C_DESC_TYPE_WATCHPORT_CALIBRATION_DATA 0x16 // Watchport Calibration Data + +#define I2C_DESC_TYPE_FIRMWARE_BLANK 0xf2 + +// Special section defined by ION +#define I2C_DESC_TYPE_ION 0 // Not defined by TI + + +struct ti_i2c_desc { + __u8 Type; // Type of descriptor + __le16 Size; // Size of data only not including header + __u8 CheckSum; // Checksum (8 bit sum of data only) + __u8 Data[0]; // Data starts here +} __attribute__((packed)); + +// for 5152 devices only (type 2 record) +// for 3410 the version is stored in the WATCHPORT_FIRMWARE_VERSION descriptor +struct ti_i2c_firmware_rec { + __u8 Ver_Major; // Firmware Major version number + __u8 Ver_Minor; // Firmware Minor version number + __u8 Data[0]; // Download starts here +} __attribute__((packed)); + + +struct watchport_firmware_version { +// Added 2 bytes for version number + __u8 Version_Major; // Download Version (for Watchport) + __u8 Version_Minor; +} __attribute__((packed)); + + +// Structure of header of download image in fw_down.h +struct ti_i2c_image_header { + __le16 Length; + __u8 CheckSum; +} __attribute__((packed)); + +struct ti_basic_descriptor { + __u8 Power; // Self powered + // bit 7: 1 - power switching supported + // 0 - power switching not supported + // + // bit 0: 1 - self powered + // 0 - bus powered + // + // + __u16 HubVid; // VID HUB + __u16 HubPid; // PID HUB + __u16 DevPid; // PID Edgeport + __u8 HubTime; // Time for power on to power good + __u8 HubCurrent; // HUB Current = 100ma +} __attribute__((packed)); + + +// CPU / Board Rev Definitions +#define TI_CPU_REV_5052 2 // 5052 based edgeports +#define TI_CPU_REV_3410 3 // 3410 based edgeports + +#define TI_BOARD_REV_TI_EP 0 // Basic ti based edgeport +#define TI_BOARD_REV_COMPACT 1 // Compact board +#define TI_BOARD_REV_WATCHPORT 2 // Watchport + + +#define TI_GET_CPU_REVISION(x) (__u8)((((x)>>4)&0x0f)) +#define TI_GET_BOARD_REVISION(x) (__u8)(((x)&0x0f)) + +#define TI_I2C_SIZE_MASK 0x1f // 5 bits +#define TI_GET_I2C_SIZE(x) ((((x) & TI_I2C_SIZE_MASK)+1)*256) + +#define TI_MAX_I2C_SIZE (16 * 1024) + +#define TI_MANUF_VERSION_0 0 + +// IonConig2 flags +#define TI_CONFIG2_RS232 0x01 +#define TI_CONFIG2_RS422 0x02 +#define TI_CONFIG2_RS485 0x04 +#define TI_CONFIG2_SWITCHABLE 0x08 + +#define TI_CONFIG2_WATCHPORT 0x10 + + +struct edge_ti_manuf_descriptor { + __u8 IonConfig; // Config byte for ION manufacturing use + __u8 IonConfig2; // Expansion + __u8 Version; // Version + __u8 CpuRev_BoardRev; // CPU revision level (0xF0) and Board Rev Level (0x0F) + __u8 NumPorts; // Number of ports for this UMP + __u8 NumVirtualPorts; // Number of Virtual ports + __u8 HubConfig1; // Used to configure the Hub + __u8 HubConfig2; // Used to configure the Hub + __u8 TotalPorts; // Total Number of Com Ports for the entire device (All UMPs) + __u8 Reserved; // Reserved +} __attribute__((packed)); + + +#endif // if !defined(_USBVEND_H) |