From 76cb841cb886eef6b3bee341a2266c76578724ad Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Mon, 6 May 2024 03:02:30 +0200 Subject: Adding upstream version 4.19.249. Signed-off-by: Daniel Baumann --- Documentation/powerpc/00-INDEX | 34 ++ Documentation/powerpc/DAWR-POWER9.txt | 58 +++ Documentation/powerpc/bootwrapper.txt | 141 +++++ Documentation/powerpc/cpu_families.txt | 221 ++++++++ Documentation/powerpc/cpu_features.txt | 56 ++ Documentation/powerpc/cxl.txt | 449 ++++++++++++++++ Documentation/powerpc/cxlflash.txt | 429 ++++++++++++++++ Documentation/powerpc/dscr.txt | 83 +++ Documentation/powerpc/eeh-pci-error-recovery.txt | 334 ++++++++++++ Documentation/powerpc/firmware-assisted-dump.txt | 277 ++++++++++ Documentation/powerpc/hvcs.txt | 567 +++++++++++++++++++++ Documentation/powerpc/mpc52xx.txt | 39 ++ .../powerpc/pci_iov_resource_on_powernv.txt | 301 +++++++++++ Documentation/powerpc/pmu-ebb.txt | 137 +++++ Documentation/powerpc/ptrace.txt | 151 ++++++ Documentation/powerpc/qe_firmware.txt | 295 +++++++++++ Documentation/powerpc/syscall64-abi.txt | 105 ++++ Documentation/powerpc/transactional_memory.txt | 244 +++++++++ 18 files changed, 3921 insertions(+) create mode 100644 Documentation/powerpc/00-INDEX create mode 100644 Documentation/powerpc/DAWR-POWER9.txt create mode 100644 Documentation/powerpc/bootwrapper.txt create mode 100644 Documentation/powerpc/cpu_families.txt create mode 100644 Documentation/powerpc/cpu_features.txt create mode 100644 Documentation/powerpc/cxl.txt create mode 100644 Documentation/powerpc/cxlflash.txt create mode 100644 Documentation/powerpc/dscr.txt create mode 100644 Documentation/powerpc/eeh-pci-error-recovery.txt create mode 100644 Documentation/powerpc/firmware-assisted-dump.txt create mode 100644 Documentation/powerpc/hvcs.txt create mode 100644 Documentation/powerpc/mpc52xx.txt create mode 100644 Documentation/powerpc/pci_iov_resource_on_powernv.txt create mode 100644 Documentation/powerpc/pmu-ebb.txt create mode 100644 Documentation/powerpc/ptrace.txt create mode 100644 Documentation/powerpc/qe_firmware.txt create mode 100644 Documentation/powerpc/syscall64-abi.txt create mode 100644 Documentation/powerpc/transactional_memory.txt (limited to 'Documentation/powerpc') diff --git a/Documentation/powerpc/00-INDEX b/Documentation/powerpc/00-INDEX new file mode 100644 index 000000000..9dc845cf7 --- /dev/null +++ b/Documentation/powerpc/00-INDEX @@ -0,0 +1,34 @@ +Index of files in Documentation/powerpc. If you think something about +Linux/PPC needs an entry here, needs correction or you've written one +please mail me. + Cort Dougan (cort@fsmlabs.com) + +00-INDEX + - this file +bootwrapper.txt + - Information on how the powerpc kernel is wrapped for boot on various + different platforms. +cpu_features.txt + - info on how we support a variety of CPUs with minimal compile-time + options. +cxl.txt + - Overview of the CXL driver. +eeh-pci-error-recovery.txt + - info on PCI Bus EEH Error Recovery +firmware-assisted-dump.txt + - Documentation on the firmware assisted dump mechanism "fadump". +hvcs.txt + - IBM "Hypervisor Virtual Console Server" Installation Guide +mpc52xx.txt + - Linux 2.6.x on MPC52xx family +pmu-ebb.txt + - Description of the API for using the PMU with Event Based Branches. +qe_firmware.txt + - describes the layout of firmware binaries for the Freescale QUICC + Engine and the code that parses and uploads the microcode therein. +ptrace.txt + - Information on the ptrace interfaces for hardware debug registers. +transactional_memory.txt + - Overview of the Power8 transactional memory support. +dscr.txt + - Overview DSCR (Data Stream Control Register) support. diff --git a/Documentation/powerpc/DAWR-POWER9.txt b/Documentation/powerpc/DAWR-POWER9.txt new file mode 100644 index 000000000..2feaa6619 --- /dev/null +++ b/Documentation/powerpc/DAWR-POWER9.txt @@ -0,0 +1,58 @@ +DAWR issues on POWER9 +============================ + +On POWER9 the DAWR can cause a checkstop if it points to cache +inhibited (CI) memory. Currently Linux has no way to disinguish CI +memory when configuring the DAWR, so (for now) the DAWR is disabled by +this commit: + + commit 9654153158d3e0684a1bdb76dbababdb7111d5a0 + Author: Michael Neuling + Date: Tue Mar 27 15:37:24 2018 +1100 + powerpc: Disable DAWR in the base POWER9 CPU features + +Technical Details: +============================ + +DAWR has 6 different ways of being set. +1) ptrace +2) h_set_mode(DAWR) +3) h_set_dabr() +4) kvmppc_set_one_reg() +5) xmon + +For ptrace, we now advertise zero breakpoints on POWER9 via the +PPC_PTRACE_GETHWDBGINFO call. This results in GDB falling back to +software emulation of the watchpoint (which is slow). + +h_set_mode(DAWR) and h_set_dabr() will now return an error to the +guest on a POWER9 host. Current Linux guests ignore this error, so +they will silently not get the DAWR. + +kvmppc_set_one_reg() will store the value in the vcpu but won't +actually set it on POWER9 hardware. This is done so we don't break +migration from POWER8 to POWER9, at the cost of silently losing the +DAWR on the migration. + +For xmon, the 'bd' command will return an error on P9. + +Consequences for users +============================ + +For GDB watchpoints (ie 'watch' command) on POWER9 bare metal , GDB +will accept the command. Unfortunately since there is no hardware +support for the watchpoint, GDB will software emulate the watchpoint +making it run very slowly. + +The same will also be true for any guests started on a POWER9 +host. The watchpoint will fail and GDB will fall back to software +emulation. + +If a guest is started on a POWER8 host, GDB will accept the watchpoint +and configure the hardware to use the DAWR. This will run at full +speed since it can use the hardware emulation. Unfortunately if this +guest is migrated to a POWER9 host, the watchpoint will be lost on the +POWER9. Loads and stores to the watchpoint locations will not be +trapped in GDB. The watchpoint is remembered, so if the guest is +migrated back to the POWER8 host, it will start working again. + diff --git a/Documentation/powerpc/bootwrapper.txt b/Documentation/powerpc/bootwrapper.txt new file mode 100644 index 000000000..d60fced5e --- /dev/null +++ b/Documentation/powerpc/bootwrapper.txt @@ -0,0 +1,141 @@ +The PowerPC boot wrapper +------------------------ +Copyright (C) Secret Lab Technologies Ltd. + +PowerPC image targets compresses and wraps the kernel image (vmlinux) with +a boot wrapper to make it usable by the system firmware. There is no +standard PowerPC firmware interface, so the boot wrapper is designed to +be adaptable for each kind of image that needs to be built. + +The boot wrapper can be found in the arch/powerpc/boot/ directory. The +Makefile in that directory has targets for all the available image types. +The different image types are used to support all of the various firmware +interfaces found on PowerPC platforms. OpenFirmware is the most commonly +used firmware type on general purpose PowerPC systems from Apple, IBM and +others. U-Boot is typically found on embedded PowerPC hardware, but there +are a handful of other firmware implementations which are also popular. Each +firmware interface requires a different image format. + +The boot wrapper is built from the makefile in arch/powerpc/boot/Makefile and +it uses the wrapper script (arch/powerpc/boot/wrapper) to generate target +image. The details of the build system is discussed in the next section. +Currently, the following image format targets exist: + + cuImage.%: Backwards compatible uImage for older version of + U-Boot (for versions that don't understand the device + tree). This image embeds a device tree blob inside + the image. The boot wrapper, kernel and device tree + are all embedded inside the U-Boot uImage file format + with boot wrapper code that extracts data from the old + bd_info structure and loads the data into the device + tree before jumping into the kernel. + Because of the series of #ifdefs found in the + bd_info structure used in the old U-Boot interfaces, + cuImages are platform specific. Each specific + U-Boot platform has a different platform init file + which populates the embedded device tree with data + from the platform specific bd_info file. The platform + specific cuImage platform init code can be found in + arch/powerpc/boot/cuboot.*.c. Selection of the correct + cuImage init code for a specific board can be found in + the wrapper structure. + dtbImage.%: Similar to zImage, except device tree blob is embedded + inside the image instead of provided by firmware. The + output image file can be either an elf file or a flat + binary depending on the platform. + dtbImages are used on systems which do not have an + interface for passing a device tree directly. + dtbImages are similar to simpleImages except that + dtbImages have platform specific code for extracting + data from the board firmware, but simpleImages do not + talk to the firmware at all. + PlayStation 3 support uses dtbImage. So do Embedded + Planet boards using the PlanetCore firmware. Board + specific initialization code is typically found in a + file named arch/powerpc/boot/.c; but this + can be overridden by the wrapper script. + simpleImage.%: Firmware independent compressed image that does not + depend on any particular firmware interface and embeds + a device tree blob. This image is a flat binary that + can be loaded to any location in RAM and jumped to. + Firmware cannot pass any configuration data to the + kernel with this image type and it depends entirely on + the embedded device tree for all information. + The simpleImage is useful for booting systems with + an unknown firmware interface or for booting from + a debugger when no firmware is present (such as on + the Xilinx Virtex platform). The only assumption that + simpleImage makes is that RAM is correctly initialized + and that the MMU is either off or has RAM mapped to + base address 0. + simpleImage also supports inserting special platform + specific initialization code to the start of the bootup + sequence. The virtex405 platform uses this feature to + ensure that the cache is invalidated before caching + is enabled. Platform specific initialization code is + added as part of the wrapper script and is keyed on + the image target name. For example, all + simpleImage.virtex405-* targets will add the + virtex405-head.S initialization code (This also means + that the dts file for virtex405 targets should be + named (virtex405-.dts). Search the wrapper + script for 'virtex405' and see the file + arch/powerpc/boot/virtex405-head.S for details. + treeImage.%; Image format for used with OpenBIOS firmware found + on some ppc4xx hardware. This image embeds a device + tree blob inside the image. + uImage: Native image format used by U-Boot. The uImage target + does not add any boot code. It just wraps a compressed + vmlinux in the uImage data structure. This image + requires a version of U-Boot that is able to pass + a device tree to the kernel at boot. If using an older + version of U-Boot, then you need to use a cuImage + instead. + zImage.%: Image format which does not embed a device tree. + Used by OpenFirmware and other firmware interfaces + which are able to supply a device tree. This image + expects firmware to provide the device tree at boot. + Typically, if you have general purpose PowerPC + hardware then you want this image format. + +Image types which embed a device tree blob (simpleImage, dtbImage, treeImage, +and cuImage) all generate the device tree blob from a file in the +arch/powerpc/boot/dts/ directory. The Makefile selects the correct device +tree source based on the name of the target. Therefore, if the kernel is +built with 'make treeImage.walnut simpleImage.virtex405-ml403', then the +build system will use arch/powerpc/boot/dts/walnut.dts to build +treeImage.walnut and arch/powerpc/boot/dts/virtex405-ml403.dts to build +the simpleImage.virtex405-ml403. + +Two special targets called 'zImage' and 'zImage.initrd' also exist. These +targets build all the default images as selected by the kernel configuration. +Default images are selected by the boot wrapper Makefile +(arch/powerpc/boot/Makefile) by adding targets to the $image-y variable. Look +at the Makefile to see which default image targets are available. + +How it is built +--------------- +arch/powerpc is designed to support multiplatform kernels, which means +that a single vmlinux image can be booted on many different target boards. +It also means that the boot wrapper must be able to wrap for many kinds of +images on a single build. The design decision was made to not use any +conditional compilation code (#ifdef, etc) in the boot wrapper source code. +All of the boot wrapper pieces are buildable at any time regardless of the +kernel configuration. Building all the wrapper bits on every kernel build +also ensures that obscure parts of the wrapper are at the very least compile +tested in a large variety of environments. + +The wrapper is adapted for different image types at link time by linking in +just the wrapper bits that are appropriate for the image type. The 'wrapper +script' (found in arch/powerpc/boot/wrapper) is called by the Makefile and +is responsible for selecting the correct wrapper bits for the image type. +The arguments are well documented in the script's comment block, so they +are not repeated here. However, it is worth mentioning that the script +uses the -p (platform) argument as the main method of deciding which wrapper +bits to compile in. Look for the large 'case "$platform" in' block in the +middle of the script. This is also the place where platform specific fixups +can be selected by changing the link order. + +In particular, care should be taken when working with cuImages. cuImage +wrapper bits are very board specific and care should be taken to make sure +the target you are trying to build is supported by the wrapper bits. diff --git a/Documentation/powerpc/cpu_families.txt b/Documentation/powerpc/cpu_families.txt new file mode 100644 index 000000000..fc08e22fe --- /dev/null +++ b/Documentation/powerpc/cpu_families.txt @@ -0,0 +1,221 @@ +CPU Families +============ + +This document tries to summarise some of the different cpu families that exist +and are supported by arch/powerpc. + + +Book3S (aka sPAPR) +------------------ + + - Hash MMU + - Mix of 32 & 64 bit + + +--------------+ +----------------+ + | Old POWER | --------------> | RS64 (threads) | + +--------------+ +----------------+ + | + | + v + +--------------+ +----------------+ +------+ + | 601 | --------------> | 603 | ---> | e300 | + +--------------+ +----------------+ +------+ + | | + | | + v v + +--------------+ +----------------+ +-------+ + | 604 | | 750 (G3) | ---> | 750CX | + +--------------+ +----------------+ +-------+ + | | | + | | | + v v v + +--------------+ +----------------+ +-------+ + | 620 (64 bit) | | 7400 | | 750CL | + +--------------+ +----------------+ +-------+ + | | | + | | | + v v v + +--------------+ +----------------+ +-------+ + | POWER3/630 | | 7410 | | 750FX | + +--------------+ +----------------+ +-------+ + | | + | | + v v + +--------------+ +----------------+ + | POWER3+ | | 7450 | + +--------------+ +----------------+ + | | + | | + v v + +--------------+ +----------------+ + | POWER4 | | 7455 | + +--------------+ +----------------+ + | | + | | + v v + +--------------+ +-------+ +----------------+ + | POWER4+ | --> | 970 | | 7447 | + +--------------+ +-------+ +----------------+ + | | | + | | | + v v v + +--------------+ +-------+ +----------------+ + | POWER5 | | 970FX | | 7448 | + +--------------+ +-------+ +----------------+ + | | | + | | | + v v v + +--------------+ +-------+ +----------------+ + | POWER5+ | | 970MP | | e600 | + +--------------+ +-------+ +----------------+ + | + | + v + +--------------+ + | POWER5++ | + +--------------+ + | + | + v + +--------------+ +-------+ + | POWER6 | <-?-> | Cell | + +--------------+ +-------+ + | + | + v + +--------------+ + | POWER7 | + +--------------+ + | + | + v + +--------------+ + | POWER7+ | + +--------------+ + | + | + v + +--------------+ + | POWER8 | + +--------------+ + + + +---------------+ + | PA6T (64 bit) | + +---------------+ + + +IBM BookE +--------- + + - Software loaded TLB. + - All 32 bit + + +--------------+ + | 401 | + +--------------+ + | + | + v + +--------------+ + | 403 | + +--------------+ + | + | + v + +--------------+ + | 405 | + +--------------+ + | + | + v + +--------------+ + | 440 | + +--------------+ + | + | + v + +--------------+ +----------------+ + | 450 | --> | BG/P | + +--------------+ +----------------+ + | + | + v + +--------------+ + | 460 | + +--------------+ + | + | + v + +--------------+ + | 476 | + +--------------+ + + +Motorola/Freescale 8xx +---------------------- + + - Software loaded with hardware assist. + - All 32 bit + + +-------------+ + | MPC8xx Core | + +-------------+ + + +Freescale BookE +--------------- + + - Software loaded TLB. + - e6500 adds HW loaded indirect TLB entries. + - Mix of 32 & 64 bit + + +--------------+ + | e200 | + +--------------+ + + + +--------------------------------+ + | e500 | + +--------------------------------+ + | + | + v + +--------------------------------+ + | e500v2 | + +--------------------------------+ + | + | + v + +--------------------------------+ + | e500mc (Book3e) | + +--------------------------------+ + | + | + v + +--------------------------------+ + | e5500 (64 bit) | + +--------------------------------+ + | + | + v + +--------------------------------+ + | e6500 (HW TLB) (Multithreaded) | + +--------------------------------+ + + +IBM A2 core +----------- + + - Book3E, software loaded TLB + HW loaded indirect TLB entries. + - 64 bit + + +--------------+ +----------------+ + | A2 core | --> | WSP | + +--------------+ +----------------+ + | + | + v + +--------------+ + | BG/Q | + +--------------+ diff --git a/Documentation/powerpc/cpu_features.txt b/Documentation/powerpc/cpu_features.txt new file mode 100644 index 000000000..ae09df872 --- /dev/null +++ b/Documentation/powerpc/cpu_features.txt @@ -0,0 +1,56 @@ +Hollis Blanchard +5 Jun 2002 + +This document describes the system (including self-modifying code) used in the +PPC Linux kernel to support a variety of PowerPC CPUs without requiring +compile-time selection. + +Early in the boot process the ppc32 kernel detects the current CPU type and +chooses a set of features accordingly. Some examples include Altivec support, +split instruction and data caches, and if the CPU supports the DOZE and NAP +sleep modes. + +Detection of the feature set is simple. A list of processors can be found in +arch/powerpc/kernel/cputable.c. The PVR register is masked and compared with +each value in the list. If a match is found, the cpu_features of cur_cpu_spec +is assigned to the feature bitmask for this processor and a __setup_cpu +function is called. + +C code may test 'cur_cpu_spec[smp_processor_id()]->cpu_features' for a +particular feature bit. This is done in quite a few places, for example +in ppc_setup_l2cr(). + +Implementing cpufeatures in assembly is a little more involved. There are +several paths that are performance-critical and would suffer if an array +index, structure dereference, and conditional branch were added. To avoid the +performance penalty but still allow for runtime (rather than compile-time) CPU +selection, unused code is replaced by 'nop' instructions. This nop'ing is +based on CPU 0's capabilities, so a multi-processor system with non-identical +processors will not work (but such a system would likely have other problems +anyways). + +After detecting the processor type, the kernel patches out sections of code +that shouldn't be used by writing nop's over it. Using cpufeatures requires +just 2 macros (found in arch/powerpc/include/asm/cputable.h), as seen in head.S +transfer_to_handler: + + #ifdef CONFIG_ALTIVEC + BEGIN_FTR_SECTION + mfspr r22,SPRN_VRSAVE /* if G4, save vrsave register value */ + stw r22,THREAD_VRSAVE(r23) + END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC) + #endif /* CONFIG_ALTIVEC */ + +If CPU 0 supports Altivec, the code is left untouched. If it doesn't, both +instructions are replaced with nop's. + +The END_FTR_SECTION macro has two simpler variations: END_FTR_SECTION_IFSET +and END_FTR_SECTION_IFCLR. These simply test if a flag is set (in +cur_cpu_spec[0]->cpu_features) or is cleared, respectively. These two macros +should be used in the majority of cases. + +The END_FTR_SECTION macros are implemented by storing information about this +code in the '__ftr_fixup' ELF section. When do_cpu_ftr_fixups +(arch/powerpc/kernel/misc.S) is invoked, it will iterate over the records in +__ftr_fixup, and if the required feature is not present it will loop writing +nop's from each BEGIN_FTR_SECTION to END_FTR_SECTION. diff --git a/Documentation/powerpc/cxl.txt b/Documentation/powerpc/cxl.txt new file mode 100644 index 000000000..c5e8d5098 --- /dev/null +++ b/Documentation/powerpc/cxl.txt @@ -0,0 +1,449 @@ +Coherent Accelerator Interface (CXL) +==================================== + +Introduction +============ + + The coherent accelerator interface is designed to allow the + coherent connection of accelerators (FPGAs and other devices) to a + POWER system. These devices need to adhere to the Coherent + Accelerator Interface Architecture (CAIA). + + IBM refers to this as the Coherent Accelerator Processor Interface + or CAPI. In the kernel it's referred to by the name CXL to avoid + confusion with the ISDN CAPI subsystem. + + Coherent in this context means that the accelerator and CPUs can + both access system memory directly and with the same effective + addresses. + + +Hardware overview +================= + + POWER8/9 FPGA + +----------+ +---------+ + | | | | + | CPU | | AFU | + | | | | + | | | | + | | | | + +----------+ +---------+ + | PHB | | | + | +------+ | PSL | + | | CAPP |<------>| | + +---+------+ PCIE +---------+ + + The POWER8/9 chip has a Coherently Attached Processor Proxy (CAPP) + unit which is part of the PCIe Host Bridge (PHB). This is managed + by Linux by calls into OPAL. Linux doesn't directly program the + CAPP. + + The FPGA (or coherently attached device) consists of two parts. + The POWER Service Layer (PSL) and the Accelerator Function Unit + (AFU). The AFU is used to implement specific functionality behind + the PSL. The PSL, among other things, provides memory address + translation services to allow each AFU direct access to userspace + memory. + + The AFU is the core part of the accelerator (eg. the compression, + crypto etc function). The kernel has no knowledge of the function + of the AFU. Only userspace interacts directly with the AFU. + + The PSL provides the translation and interrupt services that the + AFU needs. This is what the kernel interacts with. For example, if + the AFU needs to read a particular effective address, it sends + that address to the PSL, the PSL then translates it, fetches the + data from memory and returns it to the AFU. If the PSL has a + translation miss, it interrupts the kernel and the kernel services + the fault. The context to which this fault is serviced is based on + who owns that acceleration function. + + POWER8 <-----> PSL Version 8 is compliant to the CAIA Version 1.0. + POWER9 <-----> PSL Version 9 is compliant to the CAIA Version 2.0. + This PSL Version 9 provides new features such as: + * Interaction with the nest MMU on the P9 chip. + * Native DMA support. + * Supports sending ASB_Notify messages for host thread wakeup. + * Supports Atomic operations. + * .... + + Cards with a PSL9 won't work on a POWER8 system and cards with a + PSL8 won't work on a POWER9 system. + +AFU Modes +========= + + There are two programming modes supported by the AFU. Dedicated + and AFU directed. AFU may support one or both modes. + + When using dedicated mode only one MMU context is supported. In + this mode, only one userspace process can use the accelerator at + time. + + When using AFU directed mode, up to 16K simultaneous contexts can + be supported. This means up to 16K simultaneous userspace + applications may use the accelerator (although specific AFUs may + support fewer). In this mode, the AFU sends a 16 bit context ID + with each of its requests. This tells the PSL which context is + associated with each operation. If the PSL can't translate an + operation, the ID can also be accessed by the kernel so it can + determine the userspace context associated with an operation. + + +MMIO space +========== + + A portion of the accelerator MMIO space can be directly mapped + from the AFU to userspace. Either the whole space can be mapped or + just a per context portion. The hardware is self describing, hence + the kernel can determine the offset and size of the per context + portion. + + +Interrupts +========== + + AFUs may generate interrupts that are destined for userspace. These + are received by the kernel as hardware interrupts and passed onto + userspace by a read syscall documented below. + + Data storage faults and error interrupts are handled by the kernel + driver. + + +Work Element Descriptor (WED) +============================= + + The WED is a 64-bit parameter passed to the AFU when a context is + started. Its format is up to the AFU hence the kernel has no + knowledge of what it represents. Typically it will be the + effective address of a work queue or status block where the AFU + and userspace can share control and status information. + + + + +User API +======== + +1. AFU character devices + + For AFUs operating in AFU directed mode, two character device + files will be created. /dev/cxl/afu0.0m will correspond to a + master context and /dev/cxl/afu0.0s will correspond to a slave + context. Master contexts have access to the full MMIO space an + AFU provides. Slave contexts have access to only the per process + MMIO space an AFU provides. + + For AFUs operating in dedicated process mode, the driver will + only create a single character device per AFU called + /dev/cxl/afu0.0d. This will have access to the entire MMIO space + that the AFU provides (like master contexts in AFU directed). + + The types described below are defined in include/uapi/misc/cxl.h + + The following file operations are supported on both slave and + master devices. + + A userspace library libcxl is available here: + https://github.com/ibm-capi/libcxl + This provides a C interface to this kernel API. + +open +---- + + Opens the device and allocates a file descriptor to be used with + the rest of the API. + + A dedicated mode AFU only has one context and only allows the + device to be opened once. + + An AFU directed mode AFU can have many contexts, the device can be + opened once for each context that is available. + + When all available contexts are allocated the open call will fail + and return -ENOSPC. + + Note: IRQs need to be allocated for each context, which may limit + the number of contexts that can be created, and therefore + how many times the device can be opened. The POWER8 CAPP + supports 2040 IRQs and 3 are used by the kernel, so 2037 are + left. If 1 IRQ is needed per context, then only 2037 + contexts can be allocated. If 4 IRQs are needed per context, + then only 2037/4 = 509 contexts can be allocated. + + +ioctl +----- + + CXL_IOCTL_START_WORK: + Starts the AFU context and associates it with the current + process. Once this ioctl is successfully executed, all memory + mapped into this process is accessible to this AFU context + using the same effective addresses. No additional calls are + required to map/unmap memory. The AFU memory context will be + updated as userspace allocates and frees memory. This ioctl + returns once the AFU context is started. + + Takes a pointer to a struct cxl_ioctl_start_work: + + struct cxl_ioctl_start_work { + __u64 flags; + __u64 work_element_descriptor; + __u64 amr; + __s16 num_interrupts; + __s16 reserved1; + __s32 reserved2; + __u64 reserved3; + __u64 reserved4; + __u64 reserved5; + __u64 reserved6; + }; + + flags: + Indicates which optional fields in the structure are + valid. + + work_element_descriptor: + The Work Element Descriptor (WED) is a 64-bit argument + defined by the AFU. Typically this is an effective + address pointing to an AFU specific structure + describing what work to perform. + + amr: + Authority Mask Register (AMR), same as the powerpc + AMR. This field is only used by the kernel when the + corresponding CXL_START_WORK_AMR value is specified in + flags. If not specified the kernel will use a default + value of 0. + + num_interrupts: + Number of userspace interrupts to request. This field + is only used by the kernel when the corresponding + CXL_START_WORK_NUM_IRQS value is specified in flags. + If not specified the minimum number required by the + AFU will be allocated. The min and max number can be + obtained from sysfs. + + reserved fields: + For ABI padding and future extensions + + CXL_IOCTL_GET_PROCESS_ELEMENT: + Get the current context id, also known as the process element. + The value is returned from the kernel as a __u32. + + +mmap +---- + + An AFU may have an MMIO space to facilitate communication with the + AFU. If it does, the MMIO space can be accessed via mmap. The size + and contents of this area are specific to the particular AFU. The + size can be discovered via sysfs. + + In AFU directed mode, master contexts are allowed to map all of + the MMIO space and slave contexts are allowed to only map the per + process MMIO space associated with the context. In dedicated + process mode the entire MMIO space can always be mapped. + + This mmap call must be done after the START_WORK ioctl. + + Care should be taken when accessing MMIO space. Only 32 and 64-bit + accesses are supported by POWER8. Also, the AFU will be designed + with a specific endianness, so all MMIO accesses should consider + endianness (recommend endian(3) variants like: le64toh(), + be64toh() etc). These endian issues equally apply to shared memory + queues the WED may describe. + + +read +---- + + Reads events from the AFU. Blocks if no events are pending + (unless O_NONBLOCK is supplied). Returns -EIO in the case of an + unrecoverable error or if the card is removed. + + read() will always return an integral number of events. + + The buffer passed to read() must be at least 4K bytes. + + The result of the read will be a buffer of one or more events, + each event is of type struct cxl_event, of varying size. + + struct cxl_event { + struct cxl_event_header header; + union { + struct cxl_event_afu_interrupt irq; + struct cxl_event_data_storage fault; + struct cxl_event_afu_error afu_error; + }; + }; + + The struct cxl_event_header is defined as: + + struct cxl_event_header { + __u16 type; + __u16 size; + __u16 process_element; + __u16 reserved1; + }; + + type: + This defines the type of event. The type determines how + the rest of the event is structured. These types are + described below and defined by enum cxl_event_type. + + size: + This is the size of the event in bytes including the + struct cxl_event_header. The start of the next event can + be found at this offset from the start of the current + event. + + process_element: + Context ID of the event. + + reserved field: + For future extensions and padding. + + If the event type is CXL_EVENT_AFU_INTERRUPT then the event + structure is defined as: + + struct cxl_event_afu_interrupt { + __u16 flags; + __u16 irq; /* Raised AFU interrupt number */ + __u32 reserved1; + }; + + flags: + These flags indicate which optional fields are present + in this struct. Currently all fields are mandatory. + + irq: + The IRQ number sent by the AFU. + + reserved field: + For future extensions and padding. + + If the event type is CXL_EVENT_DATA_STORAGE then the event + structure is defined as: + + struct cxl_event_data_storage { + __u16 flags; + __u16 reserved1; + __u32 reserved2; + __u64 addr; + __u64 dsisr; + __u64 reserved3; + }; + + flags: + These flags indicate which optional fields are present in + this struct. Currently all fields are mandatory. + + address: + The address that the AFU unsuccessfully attempted to + access. Valid accesses will be handled transparently by the + kernel but invalid accesses will generate this event. + + dsisr: + This field gives information on the type of fault. It is a + copy of the DSISR from the PSL hardware when the address + fault occurred. The form of the DSISR is as defined in the + CAIA. + + reserved fields: + For future extensions + + If the event type is CXL_EVENT_AFU_ERROR then the event structure + is defined as: + + struct cxl_event_afu_error { + __u16 flags; + __u16 reserved1; + __u32 reserved2; + __u64 error; + }; + + flags: + These flags indicate which optional fields are present in + this struct. Currently all fields are Mandatory. + + error: + Error status from the AFU. Defined by the AFU. + + reserved fields: + For future extensions and padding + + +2. Card character device (powerVM guest only) + + In a powerVM guest, an extra character device is created for the + card. The device is only used to write (flash) a new image on the + FPGA accelerator. Once the image is written and verified, the + device tree is updated and the card is reset to reload the updated + image. + +open +---- + + Opens the device and allocates a file descriptor to be used with + the rest of the API. The device can only be opened once. + +ioctl +----- + +CXL_IOCTL_DOWNLOAD_IMAGE: +CXL_IOCTL_VALIDATE_IMAGE: + Starts and controls flashing a new FPGA image. Partial + reconfiguration is not supported (yet), so the image must contain + a copy of the PSL and AFU(s). Since an image can be quite large, + the caller may have to iterate, splitting the image in smaller + chunks. + + Takes a pointer to a struct cxl_adapter_image: + struct cxl_adapter_image { + __u64 flags; + __u64 data; + __u64 len_data; + __u64 len_image; + __u64 reserved1; + __u64 reserved2; + __u64 reserved3; + __u64 reserved4; + }; + + flags: + These flags indicate which optional fields are present in + this struct. Currently all fields are mandatory. + + data: + Pointer to a buffer with part of the image to write to the + card. + + len_data: + Size of the buffer pointed to by data. + + len_image: + Full size of the image. + + +Sysfs Class +=========== + + A cxl sysfs class is added under /sys/class/cxl to facilitate + enumeration and tuning of the accelerators. Its layout is + described in Documentation/ABI/testing/sysfs-class-cxl + + +Udev rules +========== + + The following udev rules could be used to create a symlink to the + most logical chardev to use in any programming mode (afuX.Yd for + dedicated, afuX.Ys for afu directed), since the API is virtually + identical for each: + + SUBSYSTEM=="cxl", ATTRS{mode}=="dedicated_process", SYMLINK="cxl/%b" + SUBSYSTEM=="cxl", ATTRS{mode}=="afu_directed", \ + KERNEL=="afu[0-9]*.[0-9]*s", SYMLINK="cxl/%b" diff --git a/Documentation/powerpc/cxlflash.txt b/Documentation/powerpc/cxlflash.txt new file mode 100644 index 000000000..a64bdaa0a --- /dev/null +++ b/Documentation/powerpc/cxlflash.txt @@ -0,0 +1,429 @@ +Introduction +============ + + The IBM Power architecture provides support for CAPI (Coherent + Accelerator Power Interface), which is available to certain PCIe slots + on Power 8 systems. CAPI can be thought of as a special tunneling + protocol through PCIe that allow PCIe adapters to look like special + purpose co-processors which can read or write an application's + memory and generate page faults. As a result, the host interface to + an adapter running in CAPI mode does not require the data buffers to + be mapped to the device's memory (IOMMU bypass) nor does it require + memory to be pinned. + + On Linux, Coherent Accelerator (CXL) kernel services present CAPI + devices as a PCI device by implementing a virtual PCI host bridge. + This abstraction simplifies the infrastructure and programming + model, allowing for drivers to look similar to other native PCI + device drivers. + + CXL provides a mechanism by which user space applications can + directly talk to a device (network or storage) bypassing the typical + kernel/device driver stack. The CXL Flash Adapter Driver enables a + user space application direct access to Flash storage. + + The CXL Flash Adapter Driver is a kernel module that sits in the + SCSI stack as a low level device driver (below the SCSI disk and + protocol drivers) for the IBM CXL Flash Adapter. This driver is + responsible for the initialization of the adapter, setting up the + special path for user space access, and performing error recovery. It + communicates directly the Flash Accelerator Functional Unit (AFU) + as described in Documentation/powerpc/cxl.txt. + + The cxlflash driver supports two, mutually exclusive, modes of + operation at the device (LUN) level: + + - Any flash device (LUN) can be configured to be accessed as a + regular disk device (i.e.: /dev/sdc). This is the default mode. + + - Any flash device (LUN) can be configured to be accessed from + user space with a special block library. This mode further + specifies the means of accessing the device and provides for + either raw access to the entire LUN (referred to as direct + or physical LUN access) or access to a kernel/AFU-mediated + partition of the LUN (referred to as virtual LUN access). The + segmentation of a disk device into virtual LUNs is assisted + by special translation services provided by the Flash AFU. + +Overview +======== + + The Coherent Accelerator Interface Architecture (CAIA) introduces a + concept of a master context. A master typically has special privileges + granted to it by the kernel or hypervisor allowing it to perform AFU + wide management and control. The master may or may not be involved + directly in each user I/O, but at the minimum is involved in the + initial setup before the user application is allowed to send requests + directly to the AFU. + + The CXL Flash Adapter Driver establishes a master context with the + AFU. It uses memory mapped I/O (MMIO) for this control and setup. The + Adapter Problem Space Memory Map looks like this: + + +-------------------------------+ + | 512 * 64 KB User MMIO | + | (per context) | + | User Accessible | + +-------------------------------+ + | 512 * 128 B per context | + | Provisioning and Control | + | Trusted Process accessible | + +-------------------------------+ + | 64 KB Global | + | Trusted Process accessible | + +-------------------------------+ + + This driver configures itself into the SCSI software stack as an + adapter driver. The driver is the only entity that is considered a + Trusted Process to program the Provisioning and Control and Global + areas in the MMIO Space shown above. The master context driver + discovers all LUNs attached to the CXL Flash adapter and instantiates + scsi block devices (/dev/sdb, /dev/sdc etc.) for each unique LUN + seen from each path. + + Once these scsi block devices are instantiated, an application + written to a specification provided by the block library may get + access to the Flash from user space (without requiring a system call). + + This master context driver also provides a series of ioctls for this + block library to enable this user space access. The driver supports + two modes for accessing the block device. + + The first mode is called a virtual mode. In this mode a single scsi + block device (/dev/sdb) may be carved up into any number of distinct + virtual LUNs. The virtual LUNs may be resized as long as the sum of + the sizes of all the virtual LUNs, along with the meta-data associated + with it does not exceed the physical capacity. + + The second mode is called the physical mode. In this mode a single + block device (/dev/sdb) may be opened directly by the block library + and the entire space for the LUN is available to the application. + + Only the physical mode provides persistence of the data. i.e. The + data written to the block device will survive application exit and + restart and also reboot. The virtual LUNs do not persist (i.e. do + not survive after the application terminates or the system reboots). + + +Block library API +================= + + Applications intending to get access to the CXL Flash from user + space should use the block library, as it abstracts the details of + interfacing directly with the cxlflash driver that are necessary for + performing administrative actions (i.e.: setup, tear down, resize). + The block library can be thought of as a 'user' of services, + implemented as IOCTLs, that are provided by the cxlflash driver + specifically for devices (LUNs) operating in user space access + mode. While it is not a requirement that applications understand + the interface between the block library and the cxlflash driver, + a high-level overview of each supported service (IOCTL) is provided + below. + + The block library can be found on GitHub: + http://github.com/open-power/capiflash + + +CXL Flash Driver LUN IOCTLs +=========================== + + Users, such as the block library, that wish to interface with a flash + device (LUN) via user space access need to use the services provided + by the cxlflash driver. As these services are implemented as ioctls, + a file descriptor handle must first be obtained in order to establish + the communication channel between a user and the kernel. This file + descriptor is obtained by opening the device special file associated + with the scsi disk device (/dev/sdb) that was created during LUN + discovery. As per the location of the cxlflash driver within the + SCSI protocol stack, this open is actually not seen by the cxlflash + driver. Upon successful open, the user receives a file descriptor + (herein referred to as fd1) that should be used for issuing the + subsequent ioctls listed below. + + The structure definitions for these IOCTLs are available in: + uapi/scsi/cxlflash_ioctl.h + +DK_CXLFLASH_ATTACH +------------------ + + This ioctl obtains, initializes, and starts a context using the CXL + kernel services. These services specify a context id (u16) by which + to uniquely identify the context and its allocated resources. The + services additionally provide a second file descriptor (herein + referred to as fd2) that is used by the block library to initiate + memory mapped I/O (via mmap()) to the CXL flash device and poll for + completion events. This file descriptor is intentionally installed by + this driver and not the CXL kernel services to allow for intermediary + notification and access in the event of a non-user-initiated close(), + such as a killed process. This design point is described in further + detail in the description for the DK_CXLFLASH_DETACH ioctl. + + There are a few important aspects regarding the "tokens" (context id + and fd2) that are provided back to the user: + + - These tokens are only valid for the process under which they + were created. The child of a forked process cannot continue + to use the context id or file descriptor created by its parent + (see DK_CXLFLASH_VLUN_CLONE for further details). + + - These tokens are only valid for the lifetime of the context and + the process under which they were created. Once either is + destroyed, the tokens are to be considered stale and subsequent + usage will result in errors. + + - A valid adapter file descriptor (fd2 >= 0) is only returned on + the initial attach for a context. Subsequent attaches to an + existing context (DK_CXLFLASH_ATTACH_REUSE_CONTEXT flag present) + do not provide the adapter file descriptor as it was previously + made known to the application. + + - When a context is no longer needed, the user shall detach from + the context via the DK_CXLFLASH_DETACH ioctl. When this ioctl + returns with a valid adapter file descriptor and the return flag + DK_CXLFLASH_APP_CLOSE_ADAP_FD is present, the application _must_ + close the adapter file descriptor following a successful detach. + + - When this ioctl returns with a valid fd2 and the return flag + DK_CXLFLASH_APP_CLOSE_ADAP_FD is present, the application _must_ + close fd2 in the following circumstances: + + + Following a successful detach of the last user of the context + + Following a successful recovery on the context's original fd2 + + In the child process of a fork(), following a clone ioctl, + on the fd2 associated with the source context + + - At any time, a close on fd2 will invalidate the tokens. Applications + should exercise caution to only close fd2 when appropriate (outlined + in the previous bullet) to avoid premature loss of I/O. + +DK_CXLFLASH_USER_DIRECT +----------------------- + This ioctl is responsible for transitioning the LUN to direct + (physical) mode access and configuring the AFU for direct access from + user space on a per-context basis. Additionally, the block size and + last logical block address (LBA) are returned to the user. + + As mentioned previously, when operating in user space access mode, + LUNs may be accessed in whole or in part. Only one mode is allowed + at a time and if one mode is active (outstanding references exist), + requests to use the LUN in a different mode are denied. + + The AFU is configured for direct access from user space by adding an + entry to the AFU's resource handle table. The index of the entry is + treated as a resource handle that is returned to the user. The user + is then able to use the handle to reference the LUN during I/O. + +DK_CXLFLASH_USER_VIRTUAL +------------------------ + This ioctl is responsible for transitioning the LUN to virtual mode + of access and configuring the AFU for virtual access from user space + on a per-context basis. Additionally, the block size and last logical + block address (LBA) are returned to the user. + + As mentioned previously, when operating in user space access mode, + LUNs may be accessed in whole or in part. Only one mode is allowed + at a time and if one mode is active (outstanding references exist), + requests to use the LUN in a different mode are denied. + + The AFU is configured for virtual access from user space by adding + an entry to the AFU's resource handle table. The index of the entry + is treated as a resource handle that is returned to the user. The + user is then able to use the handle to reference the LUN during I/O. + + By default, the virtual LUN is created with a size of 0. The user + would need to use the DK_CXLFLASH_VLUN_RESIZE ioctl to adjust the grow + the virtual LUN to a desired size. To avoid having to perform this + resize for the initial creation of the virtual LUN, the user has the + option of specifying a size as part of the DK_CXLFLASH_USER_VIRTUAL + ioctl, such that when success is returned to the user, the + resource handle that is provided is already referencing provisioned + storage. This is reflected by the last LBA being a non-zero value. + + When a LUN is accessible from more than one port, this ioctl will + return with the DK_CXLFLASH_ALL_PORTS_ACTIVE return flag set. This + provides the user with a hint that I/O can be retried in the event + of an I/O error as the LUN can be reached over multiple paths. + +DK_CXLFLASH_VLUN_RESIZE +----------------------- + This ioctl is responsible for resizing a previously created virtual + LUN and will fail if invoked upon a LUN that is not in virtual + mode. Upon success, an updated last LBA is returned to the user + indicating the new size of the virtual LUN associated with the + resource handle. + + The partitioning of virtual LUNs is jointly mediated by the cxlflash + driver and the AFU. An allocation table is kept for each LUN that is + operating in the virtual mode and used to program a LUN translation + table that the AFU references when provided with a resource handle. + + This ioctl can return -EAGAIN if an AFU sync operation takes too long. + In addition to returning a failure to user, cxlflash will also schedule + an asynchronous AFU reset. Should the user choose to retry the operation, + it is expected to succeed. If this ioctl fails with -EAGAIN, the user + can either retry the operation or treat it as a failure. + +DK_CXLFLASH_RELEASE +------------------- + This ioctl is responsible for releasing a previously obtained + reference to either a physical or virtual LUN. This can be + thought of as the inverse of the DK_CXLFLASH_USER_DIRECT or + DK_CXLFLASH_USER_VIRTUAL ioctls. Upon success, the resource handle + is no longer valid and the entry in the resource handle table is + made available to be used again. + + As part of the release process for virtual LUNs, the virtual LUN + is first resized to 0 to clear out and free the translation tables + associated with the virtual LUN reference. + +DK_CXLFLASH_DETACH +------------------ + This ioctl is responsible for unregistering a context with the + cxlflash driver and release outstanding resources that were + not explicitly released via the DK_CXLFLASH_RELEASE ioctl. Upon + success, all "tokens" which had been provided to the user from the + DK_CXLFLASH_ATTACH onward are no longer valid. + + When the DK_CXLFLASH_APP_CLOSE_ADAP_FD flag was returned on a successful + attach, the application _must_ close the fd2 associated with the context + following the detach of the final user of the context. + +DK_CXLFLASH_VLUN_CLONE +---------------------- + This ioctl is responsible for cloning a previously created + context to a more recently created context. It exists solely to + support maintaining user space access to storage after a process + forks. Upon success, the child process (which invoked the ioctl) + will have access to the same LUNs via the same resource handle(s) + as the parent, but under a different context. + + Context sharing across processes is not supported with CXL and + therefore each fork must be met with establishing a new context + for the child process. This ioctl simplifies the state management + and playback required by a user in such a scenario. When a process + forks, child process can clone the parents context by first creating + a context (via DK_CXLFLASH_ATTACH) and then using this ioctl to + perform the clone from the parent to the child. + + The clone itself is fairly simple. The resource handle and lun + translation tables are copied from the parent context to the child's + and then synced with the AFU. + + When the DK_CXLFLASH_APP_CLOSE_ADAP_FD flag was returned on a successful + attach, the application _must_ close the fd2 associated with the source + context (still resident/accessible in the parent process) following the + clone. This is to avoid a stale entry in the file descriptor table of the + child process. + + This ioctl can return -EAGAIN if an AFU sync operation takes too long. + In addition to returning a failure to user, cxlflash will also schedule + an asynchronous AFU reset. Should the user choose to retry the operation, + it is expected to succeed. If this ioctl fails with -EAGAIN, the user + can either retry the operation or treat it as a failure. + +DK_CXLFLASH_VERIFY +------------------ + This ioctl is used to detect various changes such as the capacity of + the disk changing, the number of LUNs visible changing, etc. In cases + where the changes affect the application (such as a LUN resize), the + cxlflash driver will report the changed state to the application. + + The user calls in when they want to validate that a LUN hasn't been + changed in response to a check condition. As the user is operating out + of band from the kernel, they will see these types of events without + the kernel's knowledge. When encountered, the user's architected + behavior is to call in to this ioctl, indicating what they want to + verify and passing along any appropriate information. For now, only + verifying a LUN change (ie: size different) with sense data is + supported. + +DK_CXLFLASH_RECOVER_AFU +----------------------- + This ioctl is used to drive recovery (if such an action is warranted) + of a specified user context. Any state associated with the user context + is re-established upon successful recovery. + + User contexts are put into an error condition when the device needs to + be reset or is terminating. Users are notified of this error condition + by seeing all 0xF's on an MMIO read. Upon encountering this, the + architected behavior for a user is to call into this ioctl to recover + their context. A user may also call into this ioctl at any time to + check if the device is operating normally. If a failure is returned + from this ioctl, the user is expected to gracefully clean up their + context via release/detach ioctls. Until they do, the context they + hold is not relinquished. The user may also optionally exit the process + at which time the context/resources they held will be freed as part of + the release fop. + + When the DK_CXLFLASH_APP_CLOSE_ADAP_FD flag was returned on a successful + attach, the application _must_ unmap and close the fd2 associated with the + original context following this ioctl returning success and indicating that + the context was recovered (DK_CXLFLASH_RECOVER_AFU_CONTEXT_RESET). + +DK_CXLFLASH_MANAGE_LUN +---------------------- + This ioctl is used to switch a LUN from a mode where it is available + for file-system access (legacy), to a mode where it is set aside for + exclusive user space access (superpipe). In case a LUN is visible + across multiple ports and adapters, this ioctl is used to uniquely + identify each LUN by its World Wide Node Name (WWNN). + + +CXL Flash Driver Host IOCTLs +============================ + + Each host adapter instance that is supported by the cxlflash driver + has a special character device associated with it to enable a set of + host management function. These character devices are hosted in a + class dedicated for cxlflash and can be accessed via /dev/cxlflash/*. + + Applications can be written to perform various functions using the + host ioctl APIs below. + + The structure definitions for these IOCTLs are available in: + uapi/scsi/cxlflash_ioctl.h + +HT_CXLFLASH_LUN_PROVISION +------------------------- + This ioctl is used to create and delete persistent LUNs on cxlflash + devices that lack an external LUN management interface. It is only + valid when used with AFUs that support the LUN provision capability. + + When sufficient space is available, LUNs can be created by specifying + the target port to host the LUN and a desired size in 4K blocks. Upon + success, the LUN ID and WWID of the created LUN will be returned and + the SCSI bus can be scanned to detect the change in LUN topology. Note + that partial allocations are not supported. Should a creation fail due + to a space issue, the target port can be queried for its current LUN + geometry. + + To remove a LUN, the device must first be disassociated from the Linux + SCSI subsystem. The LUN deletion can then be initiated by specifying a + target port and LUN ID. Upon success, the LUN geometry associated with + the port will be updated to reflect new number of provisioned LUNs and + available capacity. + + To query the LUN geometry of a port, the target port is specified and + upon success, the following information is presented: + + - Maximum number of provisioned LUNs allowed for the port + - Current number of provisioned LUNs for the port + - Maximum total capacity of provisioned LUNs for the port (4K blocks) + - Current total capacity of provisioned LUNs for the port (4K blocks) + + With this information, the number of available LUNs and capacity can be + can be calculated. + +HT_CXLFLASH_AFU_DEBUG +--------------------- + This ioctl is used to debug AFUs by supporting a command pass-through + interface. It is only valid when used with AFUs that support the AFU + debug capability. + + With exception of buffer management, AFU debug commands are opaque to + cxlflash and treated as pass-through. For debug commands that do require + data transfer, the user supplies an adequately sized data buffer and must + specify the data transfer direction with respect to the host. There is a + maximum transfer size of 256K imposed. Note that partial read completions + are not supported - when errors are experienced with a host read data + transfer, the data buffer is not copied back to the user. diff --git a/Documentation/powerpc/dscr.txt b/Documentation/powerpc/dscr.txt new file mode 100644 index 000000000..ece300c64 --- /dev/null +++ b/Documentation/powerpc/dscr.txt @@ -0,0 +1,83 @@ + DSCR (Data Stream Control Register) + ================================================ + +DSCR register in powerpc allows user to have some control of prefetch of data +stream in the processor. Please refer to the ISA documents or related manual +for more detailed information regarding how to use this DSCR to attain this +control of the prefetches . This document here provides an overview of kernel +support for DSCR, related kernel objects, it's functionalities and exported +user interface. + +(A) Data Structures: + + (1) thread_struct: + dscr /* Thread DSCR value */ + dscr_inherit /* Thread has changed default DSCR */ + + (2) PACA: + dscr_default /* per-CPU DSCR default value */ + + (3) sysfs.c: + dscr_default /* System DSCR default value */ + +(B) Scheduler Changes: + + Scheduler will write the per-CPU DSCR default which is stored in the + CPU's PACA value into the register if the thread has dscr_inherit value + cleared which means that it has not changed the default DSCR till now. + If the dscr_inherit value is set which means that it has changed the + default DSCR value, scheduler will write the changed value which will + now be contained in thread struct's dscr into the register instead of + the per-CPU default PACA based DSCR value. + + NOTE: Please note here that the system wide global DSCR value never + gets used directly in the scheduler process context switch at all. + +(C) SYSFS Interface: + + Global DSCR default: /sys/devices/system/cpu/dscr_default + CPU specific DSCR default: /sys/devices/system/cpu/cpuN/dscr + + Changing the global DSCR default in the sysfs will change all the CPU + specific DSCR defaults immediately in their PACA structures. Again if + the current process has the dscr_inherit clear, it also writes the new + value into every CPU's DSCR register right away and updates the current + thread's DSCR value as well. + + Changing the CPU specific DSCR default value in the sysfs does exactly + the same thing as above but unlike the global one above, it just changes + stuff for that particular CPU instead for all the CPUs on the system. + +(D) User Space Instructions: + + The DSCR register can be accessed in the user space using any of these + two SPR numbers available for that purpose. + + (1) Problem state SPR: 0x03 (Un-privileged, POWER8 only) + (2) Privileged state SPR: 0x11 (Privileged) + + Accessing DSCR through privileged SPR number (0x11) from user space + works, as it is emulated following an illegal instruction exception + inside the kernel. Both mfspr and mtspr instructions are emulated. + + Accessing DSCR through user level SPR (0x03) from user space will first + create a facility unavailable exception. Inside this exception handler + all mfspr instruction based read attempts will get emulated and returned + where as the first mtspr instruction based write attempts will enable + the DSCR facility for the next time around (both for read and write) by + setting DSCR facility in the FSCR register. + +(E) Specifics about 'dscr_inherit': + + The thread struct element 'dscr_inherit' represents whether the thread + in question has attempted and changed the DSCR itself using any of the + following methods. This element signifies whether the thread wants to + use the CPU default DSCR value or its own changed DSCR value in the + kernel. + + (1) mtspr instruction (SPR number 0x03) + (2) mtspr instruction (SPR number 0x11) + (3) ptrace interface (Explicitly set user DSCR value) + + Any child of the process created after this event in the process inherits + this same behaviour as well. diff --git a/Documentation/powerpc/eeh-pci-error-recovery.txt b/Documentation/powerpc/eeh-pci-error-recovery.txt new file mode 100644 index 000000000..678189280 --- /dev/null +++ b/Documentation/powerpc/eeh-pci-error-recovery.txt @@ -0,0 +1,334 @@ + + + PCI Bus EEH Error Recovery + -------------------------- + Linas Vepstas + + 12 January 2005 + + +Overview: +--------- +The IBM POWER-based pSeries and iSeries computers include PCI bus +controller chips that have extended capabilities for detecting and +reporting a large variety of PCI bus error conditions. These features +go under the name of "EEH", for "Enhanced Error Handling". The EEH +hardware features allow PCI bus errors to be cleared and a PCI +card to be "rebooted", without also having to reboot the operating +system. + +This is in contrast to traditional PCI error handling, where the +PCI chip is wired directly to the CPU, and an error would cause +a CPU machine-check/check-stop condition, halting the CPU entirely. +Another "traditional" technique is to ignore such errors, which +can lead to data corruption, both of user data or of kernel data, +hung/unresponsive adapters, or system crashes/lockups. Thus, +the idea behind EEH is that the operating system can become more +reliable and robust by protecting it from PCI errors, and giving +the OS the ability to "reboot"/recover individual PCI devices. + +Future systems from other vendors, based on the PCI-E specification, +may contain similar features. + + +Causes of EEH Errors +-------------------- +EEH was originally designed to guard against hardware failure, such +as PCI cards dying from heat, humidity, dust, vibration and bad +electrical connections. The vast majority of EEH errors seen in +"real life" are due to either poorly seated PCI cards, or, +unfortunately quite commonly, due to device driver bugs, device firmware +bugs, and sometimes PCI card hardware bugs. + +The most common software bug, is one that causes the device to +attempt to DMA to a location in system memory that has not been +reserved for DMA access for that card. This is a powerful feature, +as it prevents what; otherwise, would have been silent memory +corruption caused by the bad DMA. A number of device driver +bugs have been found and fixed in this way over the past few +years. Other possible causes of EEH errors include data or +address line parity errors (for example, due to poor electrical +connectivity due to a poorly seated card), and PCI-X split-completion +errors (due to software, device firmware, or device PCI hardware bugs). +The vast majority of "true hardware failures" can be cured by +physically removing and re-seating the PCI card. + + +Detection and Recovery +---------------------- +In the following discussion, a generic overview of how to detect +and recover from EEH errors will be presented. This is followed +by an overview of how the current implementation in the Linux +kernel does it. The actual implementation is subject to change, +and some of the finer points are still being debated. These +may in turn be swayed if or when other architectures implement +similar functionality. + +When a PCI Host Bridge (PHB, the bus controller connecting the +PCI bus to the system CPU electronics complex) detects a PCI error +condition, it will "isolate" the affected PCI card. Isolation +will block all writes (either to the card from the system, or +from the card to the system), and it will cause all reads to +return all-ff's (0xff, 0xffff, 0xffffffff for 8/16/32-bit reads). +This value was chosen because it is the same value you would +get if the device was physically unplugged from the slot. +This includes access to PCI memory, I/O space, and PCI config +space. Interrupts; however, will continued to be delivered. + +Detection and recovery are performed with the aid of ppc64 +firmware. The programming interfaces in the Linux kernel +into the firmware are referred to as RTAS (Run-Time Abstraction +Services). The Linux kernel does not (should not) access +the EEH function in the PCI chipsets directly, primarily because +there are a number of different chipsets out there, each with +different interfaces and quirks. The firmware provides a +uniform abstraction layer that will work with all pSeries +and iSeries hardware (and be forwards-compatible). + +If the OS or device driver suspects that a PCI slot has been +EEH-isolated, there is a firmware call it can make to determine if +this is the case. If so, then the device driver should put itself +into a consistent state (given that it won't be able to complete any +pending work) and start recovery of the card. Recovery normally +would consist of resetting the PCI device (holding the PCI #RST +line high for two seconds), followed by setting up the device +config space (the base address registers (BAR's), latency timer, +cache line size, interrupt line, and so on). This is followed by a +reinitialization of the device driver. In a worst-case scenario, +the power to the card can be toggled, at least on hot-plug-capable +slots. In principle, layers far above the device driver probably +do not need to know that the PCI card has been "rebooted" in this +way; ideally, there should be at most a pause in Ethernet/disk/USB +I/O while the card is being reset. + +If the card cannot be recovered after three or four resets, the +kernel/device driver should assume the worst-case scenario, that the +card has died completely, and report this error to the sysadmin. +In addition, error messages are reported through RTAS and also through +syslogd (/var/log/messages) to alert the sysadmin of PCI resets. +The correct way to deal with failed adapters is to use the standard +PCI hotplug tools to remove and replace the dead card. + + +Current PPC64 Linux EEH Implementation +-------------------------------------- +At this time, a generic EEH recovery mechanism has been implemented, +so that individual device drivers do not need to be modified to support +EEH recovery. This generic mechanism piggy-backs on the PCI hotplug +infrastructure, and percolates events up through the userspace/udev +infrastructure. Following is a detailed description of how this is +accomplished. + +EEH must be enabled in the PHB's very early during the boot process, +and if a PCI slot is hot-plugged. The former is performed by +eeh_init() in arch/powerpc/platforms/pseries/eeh.c, and the later by +drivers/pci/hotplug/pSeries_pci.c calling in to the eeh.c code. +EEH must be enabled before a PCI scan of the device can proceed. +Current Power5 hardware will not work unless EEH is enabled; +although older Power4 can run with it disabled. Effectively, +EEH can no longer be turned off. PCI devices *must* be +registered with the EEH code; the EEH code needs to know about +the I/O address ranges of the PCI device in order to detect an +error. Given an arbitrary address, the routine +pci_get_device_by_addr() will find the pci device associated +with that address (if any). + +The default arch/powerpc/include/asm/io.h macros readb(), inb(), insb(), +etc. include a check to see if the i/o read returned all-0xff's. +If so, these make a call to eeh_dn_check_failure(), which in turn +asks the firmware if the all-ff's value is the sign of a true EEH +error. If it is not, processing continues as normal. The grand +total number of these false alarms or "false positives" can be +seen in /proc/ppc64/eeh (subject to change). Normally, almost +all of these occur during boot, when the PCI bus is scanned, where +a large number of 0xff reads are part of the bus scan procedure. + +If a frozen slot is detected, code in +arch/powerpc/platforms/pseries/eeh.c will print a stack trace to +syslog (/var/log/messages). This stack trace has proven to be very +useful to device-driver authors for finding out at what point the EEH +error was detected, as the error itself usually occurs slightly +beforehand. + +Next, it uses the Linux kernel notifier chain/work queue mechanism to +allow any interested parties to find out about the failure. Device +drivers, or other parts of the kernel, can use +eeh_register_notifier(struct notifier_block *) to find out about EEH +events. The event will include a pointer to the pci device, the +device node and some state info. Receivers of the event can "do as +they wish"; the default handler will be described further in this +section. + +To assist in the recovery of the device, eeh.c exports the +following functions: + +rtas_set_slot_reset() -- assert the PCI #RST line for 1/8th of a second +rtas_configure_bridge() -- ask firmware to configure any PCI bridges + located topologically under the pci slot. +eeh_save_bars() and eeh_restore_bars(): save and restore the PCI + config-space info for a device and any devices under it. + + +A handler for the EEH notifier_block events is implemented in +drivers/pci/hotplug/pSeries_pci.c, called handle_eeh_events(). +It saves the device BAR's and then calls rpaphp_unconfig_pci_adapter(). +This last call causes the device driver for the card to be stopped, +which causes uevents to go out to user space. This triggers +user-space scripts that might issue commands such as "ifdown eth0" +for ethernet cards, and so on. This handler then sleeps for 5 seconds, +hoping to give the user-space scripts enough time to complete. +It then resets the PCI card, reconfigures the device BAR's, and +any bridges underneath. It then calls rpaphp_enable_pci_slot(), +which restarts the device driver and triggers more user-space +events (for example, calling "ifup eth0" for ethernet cards). + + +Device Shutdown and User-Space Events +------------------------------------- +This section documents what happens when a pci slot is unconfigured, +focusing on how the device driver gets shut down, and on how the +events get delivered to user-space scripts. + +Following is an example sequence of events that cause a device driver +close function to be called during the first phase of an EEH reset. +The following sequence is an example of the pcnet32 device driver. + + rpa_php_unconfig_pci_adapter (struct slot *) // in rpaphp_pci.c + { + calls + pci_remove_bus_device (struct pci_dev *) // in /drivers/pci/remove.c + { + calls + pci_destroy_dev (struct pci_dev *) + { + calls + device_unregister (&dev->dev) // in /drivers/base/core.c + { + calls + device_del (struct device *) + { + calls + bus_remove_device() // in /drivers/base/bus.c + { + calls + device_release_driver() + { + calls + struct device_driver->remove() which is just + pci_device_remove() // in /drivers/pci/pci_driver.c + { + calls + struct pci_driver->remove() which is just + pcnet32_remove_one() // in /drivers/net/pcnet32.c + { + calls + unregister_netdev() // in /net/core/dev.c + { + calls + dev_close() // in /net/core/dev.c + { + calls dev->stop(); + which is just pcnet32_close() // in pcnet32.c + { + which does what you wanted + to stop the device + } + } + } + which + frees pcnet32 device driver memory + } + }}}}}} + + + in drivers/pci/pci_driver.c, + struct device_driver->remove() is just pci_device_remove() + which calls struct pci_driver->remove() which is pcnet32_remove_one() + which calls unregister_netdev() (in net/core/dev.c) + which calls dev_close() (in net/core/dev.c) + which calls dev->stop() which is pcnet32_close() + which then does the appropriate shutdown. + +--- +Following is the analogous stack trace for events sent to user-space +when the pci device is unconfigured. + +rpa_php_unconfig_pci_adapter() { // in rpaphp_pci.c + calls + pci_remove_bus_device (struct pci_dev *) { // in /drivers/pci/remove.c + calls + pci_destroy_dev (struct pci_dev *) { + calls + device_unregister (&dev->dev) { // in /drivers/base/core.c + calls + device_del(struct device * dev) { // in /drivers/base/core.c + calls + kobject_del() { //in /libs/kobject.c + calls + kobject_uevent() { // in /libs/kobject.c + calls + kset_uevent() { // in /lib/kobject.c + calls + kset->uevent_ops->uevent() // which is really just + a call to + dev_uevent() { // in /drivers/base/core.c + calls + dev->bus->uevent() which is really just a call to + pci_uevent () { // in drivers/pci/hotplug.c + which prints device name, etc.... + } + } + then kobject_uevent() sends a netlink uevent to userspace + --> userspace uevent + (during early boot, nobody listens to netlink events and + kobject_uevent() executes uevent_helper[], which runs the + event process /sbin/hotplug) + } + } + kobject_del() then calls sysfs_remove_dir(), which would + trigger any user-space daemon that was watching /sysfs, + and notice the delete event. + + +Pro's and Con's of the Current Design +------------------------------------- +There are several issues with the current EEH software recovery design, +which may be addressed in future revisions. But first, note that the +big plus of the current design is that no changes need to be made to +individual device drivers, so that the current design throws a wide net. +The biggest negative of the design is that it potentially disturbs +network daemons and file systems that didn't need to be disturbed. + +-- A minor complaint is that resetting the network card causes + user-space back-to-back ifdown/ifup burps that potentially disturb + network daemons, that didn't need to even know that the pci + card was being rebooted. + +-- A more serious concern is that the same reset, for SCSI devices, + causes havoc to mounted file systems. Scripts cannot post-facto + unmount a file system without flushing pending buffers, but this + is impossible, because I/O has already been stopped. Thus, + ideally, the reset should happen at or below the block layer, + so that the file systems are not disturbed. + + Reiserfs does not tolerate errors returned from the block device. + Ext3fs seems to be tolerant, retrying reads/writes until it does + succeed. Both have been only lightly tested in this scenario. + + The SCSI-generic subsystem already has built-in code for performing + SCSI device resets, SCSI bus resets, and SCSI host-bus-adapter + (HBA) resets. These are cascaded into a chain of attempted + resets if a SCSI command fails. These are completely hidden + from the block layer. It would be very natural to add an EEH + reset into this chain of events. + +-- If a SCSI error occurs for the root device, all is lost unless + the sysadmin had the foresight to run /bin, /sbin, /etc, /var + and so on, out of ramdisk/tmpfs. + + +Conclusions +----------- +There's forward progress ... + + diff --git a/Documentation/powerpc/firmware-assisted-dump.txt b/Documentation/powerpc/firmware-assisted-dump.txt new file mode 100644 index 000000000..bdd344aa1 --- /dev/null +++ b/Documentation/powerpc/firmware-assisted-dump.txt @@ -0,0 +1,277 @@ + + Firmware-Assisted Dump + ------------------------ + July 2011 + +The goal of firmware-assisted dump is to enable the dump of +a crashed system, and to do so from a fully-reset system, and +to minimize the total elapsed time until the system is back +in production use. + +- Firmware assisted dump (fadump) infrastructure is intended to replace + the existing phyp assisted dump. +- Fadump uses the same firmware interfaces and memory reservation model + as phyp assisted dump. +- Unlike phyp dump, fadump exports the memory dump through /proc/vmcore + in the ELF format in the same way as kdump. This helps us reuse the + kdump infrastructure for dump capture and filtering. +- Unlike phyp dump, userspace tool does not need to refer any sysfs + interface while reading /proc/vmcore. +- Unlike phyp dump, fadump allows user to release all the memory reserved + for dump, with a single operation of echo 1 > /sys/kernel/fadump_release_mem. +- Once enabled through kernel boot parameter, fadump can be + started/stopped through /sys/kernel/fadump_registered interface (see + sysfs files section below) and can be easily integrated with kdump + service start/stop init scripts. + +Comparing with kdump or other strategies, firmware-assisted +dump offers several strong, practical advantages: + +-- Unlike kdump, the system has been reset, and loaded + with a fresh copy of the kernel. In particular, + PCI and I/O devices have been reinitialized and are + in a clean, consistent state. +-- Once the dump is copied out, the memory that held the dump + is immediately available to the running kernel. And therefore, + unlike kdump, fadump doesn't need a 2nd reboot to get back + the system to the production configuration. + +The above can only be accomplished by coordination with, +and assistance from the Power firmware. The procedure is +as follows: + +-- The first kernel registers the sections of memory with the + Power firmware for dump preservation during OS initialization. + These registered sections of memory are reserved by the first + kernel during early boot. + +-- When a system crashes, the Power firmware will save + the low memory (boot memory of size larger of 5% of system RAM + or 256MB) of RAM to the previous registered region. It will + also save system registers, and hardware PTE's. + + NOTE: The term 'boot memory' means size of the low memory chunk + that is required for a kernel to boot successfully when + booted with restricted memory. By default, the boot memory + size will be the larger of 5% of system RAM or 256MB. + Alternatively, user can also specify boot memory size + through boot parameter 'crashkernel=' which will override + the default calculated size. Use this option if default + boot memory size is not sufficient for second kernel to + boot successfully. For syntax of crashkernel= parameter, + refer to Documentation/kdump/kdump.txt. If any offset is + provided in crashkernel= parameter, it will be ignored + as fadump uses a predefined offset to reserve memory + for boot memory dump preservation in case of a crash. + +-- After the low memory (boot memory) area has been saved, the + firmware will reset PCI and other hardware state. It will + *not* clear the RAM. It will then launch the bootloader, as + normal. + +-- The freshly booted kernel will notice that there is a new + node (ibm,dump-kernel) in the device tree, indicating that + there is crash data available from a previous boot. During + the early boot OS will reserve rest of the memory above + boot memory size effectively booting with restricted memory + size. This will make sure that the second kernel will not + touch any of the dump memory area. + +-- User-space tools will read /proc/vmcore to obtain the contents + of memory, which holds the previous crashed kernel dump in ELF + format. The userspace tools may copy this info to disk, or + network, nas, san, iscsi, etc. as desired. + +-- Once the userspace tool is done saving dump, it will echo + '1' to /sys/kernel/fadump_release_mem to release the reserved + memory back to general use, except the memory required for + next firmware-assisted dump registration. + + e.g. + # echo 1 > /sys/kernel/fadump_release_mem + +Please note that the firmware-assisted dump feature +is only available on Power6 and above systems with recent +firmware versions. + +Implementation details: +---------------------- + +During boot, a check is made to see if firmware supports +this feature on that particular machine. If it does, then +we check to see if an active dump is waiting for us. If yes +then everything but boot memory size of RAM is reserved during +early boot (See Fig. 2). This area is released once we finish +collecting the dump from user land scripts (e.g. kdump scripts) +that are run. If there is dump data, then the +/sys/kernel/fadump_release_mem file is created, and the reserved +memory is held. + +If there is no waiting dump data, then only the memory required +to hold CPU state, HPTE region, boot memory dump and elfcore +header, is usually reserved at an offset greater than boot memory +size (see Fig. 1). This area is *not* released: this region will +be kept permanently reserved, so that it can act as a receptacle +for a copy of the boot memory content in addition to CPU state +and HPTE region, in the case a crash does occur. + + o Memory Reservation during first kernel + + Low memory Top of memory + 0 boot memory size | + | | |<--Reserved dump area -->| | + V V | Permanent Reservation | V + +-----------+----------/ /---+---+----+-----------+----+------+ + | | |CPU|HPTE| DUMP |ELF | | + +-----------+----------/ /---+---+----+-----------+----+------+ + | ^ + | | + \ / + ------------------------------------------- + Boot memory content gets transferred to + reserved area by firmware at the time of + crash + Fig. 1 + + o Memory Reservation during second kernel after crash + + Low memory Top of memory + 0 boot memory size | + | |<------------- Reserved dump area ----------- -->| + V V V + +-----------+----------/ /---+---+----+-----------+----+------+ + | | |CPU|HPTE| DUMP |ELF | | + +-----------+----------/ /---+---+----+-----------+----+------+ + | | + V V + Used by second /proc/vmcore + kernel to boot + Fig. 2 + +Currently the dump will be copied from /proc/vmcore to a +a new file upon user intervention. The dump data available through +/proc/vmcore will be in ELF format. Hence the existing kdump +infrastructure (kdump scripts) to save the dump works fine with +minor modifications. + +The tools to examine the dump will be same as the ones +used for kdump. + +How to enable firmware-assisted dump (fadump): +------------------------------------- + +1. Set config option CONFIG_FA_DUMP=y and build kernel. +2. Boot into linux kernel with 'fadump=on' kernel cmdline option. +3. Optionally, user can also set 'crashkernel=' kernel cmdline + to specify size of the memory to reserve for boot memory dump + preservation. + +NOTE: 1. 'fadump_reserve_mem=' parameter has been deprecated. Instead + use 'crashkernel=' to specify size of the memory to reserve + for boot memory dump preservation. + 2. If firmware-assisted dump fails to reserve memory then it + will fallback to existing kdump mechanism if 'crashkernel=' + option is set at kernel cmdline. + +Sysfs/debugfs files: +------------ + +Firmware-assisted dump feature uses sysfs file system to hold +the control files and debugfs file to display memory reserved region. + +Here is the list of files under kernel sysfs: + + /sys/kernel/fadump_enabled + + This is used to display the fadump status. + 0 = fadump is disabled + 1 = fadump is enabled + + This interface can be used by kdump init scripts to identify if + fadump is enabled in the kernel and act accordingly. + + /sys/kernel/fadump_registered + + This is used to display the fadump registration status as well + as to control (start/stop) the fadump registration. + 0 = fadump is not registered. + 1 = fadump is registered and ready to handle system crash. + + To register fadump echo 1 > /sys/kernel/fadump_registered and + echo 0 > /sys/kernel/fadump_registered for un-register and stop the + fadump. Once the fadump is un-registered, the system crash will not + be handled and vmcore will not be captured. This interface can be + easily integrated with kdump service start/stop. + + /sys/kernel/fadump_release_mem + + This file is available only when fadump is active during + second kernel. This is used to release the reserved memory + region that are held for saving crash dump. To release the + reserved memory echo 1 to it: + + echo 1 > /sys/kernel/fadump_release_mem + + After echo 1, the content of the /sys/kernel/debug/powerpc/fadump_region + file will change to reflect the new memory reservations. + + The existing userspace tools (kdump infrastructure) can be easily + enhanced to use this interface to release the memory reserved for + dump and continue without 2nd reboot. + +Here is the list of files under powerpc debugfs: +(Assuming debugfs is mounted on /sys/kernel/debug directory.) + + /sys/kernel/debug/powerpc/fadump_region + + This file shows the reserved memory regions if fadump is + enabled otherwise this file is empty. The output format + is: + : [-] bytes, Dumped: + + e.g. + Contents when fadump is registered during first kernel + + # cat /sys/kernel/debug/powerpc/fadump_region + CPU : [0x0000006ffb0000-0x0000006fff001f] 0x40020 bytes, Dumped: 0x0 + HPTE: [0x0000006fff0020-0x0000006fff101f] 0x1000 bytes, Dumped: 0x0 + DUMP: [0x0000006fff1020-0x0000007fff101f] 0x10000000 bytes, Dumped: 0x0 + + Contents when fadump is active during second kernel + + # cat /sys/kernel/debug/powerpc/fadump_region + CPU : [0x0000006ffb0000-0x0000006fff001f] 0x40020 bytes, Dumped: 0x40020 + HPTE: [0x0000006fff0020-0x0000006fff101f] 0x1000 bytes, Dumped: 0x1000 + DUMP: [0x0000006fff1020-0x0000007fff101f] 0x10000000 bytes, Dumped: 0x10000000 + : [0x00000010000000-0x0000006ffaffff] 0x5ffb0000 bytes, Dumped: 0x5ffb0000 + +NOTE: Please refer to Documentation/filesystems/debugfs.txt on + how to mount the debugfs filesystem. + + +TODO: +----- + o Need to come up with the better approach to find out more + accurate boot memory size that is required for a kernel to + boot successfully when booted with restricted memory. + o The fadump implementation introduces a fadump crash info structure + in the scratch area before the ELF core header. The idea of introducing + this structure is to pass some important crash info data to the second + kernel which will help second kernel to populate ELF core header with + correct data before it gets exported through /proc/vmcore. The current + design implementation does not address a possibility of introducing + additional fields (in future) to this structure without affecting + compatibility. Need to come up with the better approach to address this. + The possible approaches are: + 1. Introduce version field for version tracking, bump up the version + whenever a new field is added to the structure in future. The version + field can be used to find out what fields are valid for the current + version of the structure. + 2. Reserve the area of predefined size (say PAGE_SIZE) for this + structure and have unused area as reserved (initialized to zero) + for future field additions. + The advantage of approach 1 over 2 is we don't need to reserve extra space. +--- +Author: Mahesh Salgaonkar +This document is based on the original documentation written for phyp +assisted dump by Linas Vepstas and Manish Ahuja. diff --git a/Documentation/powerpc/hvcs.txt b/Documentation/powerpc/hvcs.txt new file mode 100644 index 000000000..a730ca5a0 --- /dev/null +++ b/Documentation/powerpc/hvcs.txt @@ -0,0 +1,567 @@ +=========================================================================== + HVCS + IBM "Hypervisor Virtual Console Server" Installation Guide + for Linux Kernel 2.6.4+ + Copyright (C) 2004 IBM Corporation + +=========================================================================== +NOTE:Eight space tabs are the optimum editor setting for reading this file. +=========================================================================== + + Author(s) : Ryan S. Arnold + Date Created: March, 02, 2004 + Last Changed: August, 24, 2004 + +--------------------------------------------------------------------------- +Table of contents: + + 1. Driver Introduction: + 2. System Requirements + 3. Build Options: + 3.1 Built-in: + 3.2 Module: + 4. Installation: + 5. Connection: + 6. Disconnection: + 7. Configuration: + 8. Questions & Answers: + 9. Reporting Bugs: + +--------------------------------------------------------------------------- +1. Driver Introduction: + +This is the device driver for the IBM Hypervisor Virtual Console Server, +"hvcs". The IBM hvcs provides a tty driver interface to allow Linux user +space applications access to the system consoles of logically partitioned +operating systems (Linux and AIX) running on the same partitioned Power5 +ppc64 system. Physical hardware consoles per partition are not practical +on this hardware so system consoles are accessed by this driver using +firmware interfaces to virtual terminal devices. + +--------------------------------------------------------------------------- +2. System Requirements: + +This device driver was written using 2.6.4 Linux kernel APIs and will only +build and run on kernels of this version or later. + +This driver was written to operate solely on IBM Power5 ppc64 hardware +though some care was taken to abstract the architecture dependent firmware +calls from the driver code. + +Sysfs must be mounted on the system so that the user can determine which +major and minor numbers are associated with each vty-server. Directions +for sysfs mounting are outside the scope of this document. + +--------------------------------------------------------------------------- +3. Build Options: + +The hvcs driver registers itself as a tty driver. The tty layer +dynamically allocates a block of major and minor numbers in a quantity +requested by the registering driver. The hvcs driver asks the tty layer +for 64 of these major/minor numbers by default to use for hvcs device node +entries. + +If the default number of device entries is adequate then this driver can be +built into the kernel. If not, the default can be over-ridden by inserting +the driver as a module with insmod parameters. + +--------------------------------------------------------------------------- +3.1 Built-in: + +The following menuconfig example demonstrates selecting to build this +driver into the kernel. + + Device Drivers ---> + Character devices ---> + <*> IBM Hypervisor Virtual Console Server Support + +Begin the kernel make process. + +--------------------------------------------------------------------------- +3.2 Module: + +The following menuconfig example demonstrates selecting to build this +driver as a kernel module. + + Device Drivers ---> + Character devices ---> + IBM Hypervisor Virtual Console Server Support + +The make process will build the following kernel modules: + + hvcs.ko + hvcserver.ko + +To insert the module with the default allocation execute the following +commands in the order they appear: + + insmod hvcserver.ko + insmod hvcs.ko + +The hvcserver module contains architecture specific firmware calls and must +be inserted first, otherwise the hvcs module will not find some of the +symbols it expects. + +To override the default use an insmod parameter as follows (requesting 4 +tty devices as an example): + + insmod hvcs.ko hvcs_parm_num_devs=4 + +There is a maximum number of dev entries that can be specified on insmod. +We think that 1024 is currently a decent maximum number of server adapters +to allow. This can always be changed by modifying the constant in the +source file before building. + +NOTE: The length of time it takes to insmod the driver seems to be related +to the number of tty interfaces the registering driver requests. + +In order to remove the driver module execute the following command: + + rmmod hvcs.ko + +The recommended method for installing hvcs as a module is to use depmod to +build a current modules.dep file in /lib/modules/`uname -r` and then +execute: + +modprobe hvcs hvcs_parm_num_devs=4 + +The modules.dep file indicates that hvcserver.ko needs to be inserted +before hvcs.ko and modprobe uses this file to smartly insert the modules in +the proper order. + +The following modprobe command is used to remove hvcs and hvcserver in the +proper order: + +modprobe -r hvcs + +--------------------------------------------------------------------------- +4. Installation: + +The tty layer creates sysfs entries which contain the major and minor +numbers allocated for the hvcs driver. The following snippet of "tree" +output of the sysfs directory shows where these numbers are presented: + + sys/ + |-- *other sysfs base dirs* + | + |-- class + | |-- *other classes of devices* + | | + | `-- tty + | |-- *other tty devices* + | | + | |-- hvcs0 + | | `-- dev + | |-- hvcs1 + | | `-- dev + | |-- hvcs2 + | | `-- dev + | |-- hvcs3 + | | `-- dev + | | + | |-- *other tty devices* + | + |-- *other sysfs base dirs* + +For the above examples the following output is a result of cat'ing the +"dev" entry in the hvcs directory: + + Pow5:/sys/class/tty/hvcs0/ # cat dev + 254:0 + + Pow5:/sys/class/tty/hvcs1/ # cat dev + 254:1 + + Pow5:/sys/class/tty/hvcs2/ # cat dev + 254:2 + + Pow5:/sys/class/tty/hvcs3/ # cat dev + 254:3 + +The output from reading the "dev" attribute is the char device major and +minor numbers that the tty layer has allocated for this driver's use. Most +systems running hvcs will already have the device entries created or udev +will do it automatically. + +Given the example output above, to manually create a /dev/hvcs* node entry +mknod can be used as follows: + + mknod /dev/hvcs0 c 254 0 + mknod /dev/hvcs1 c 254 1 + mknod /dev/hvcs2 c 254 2 + mknod /dev/hvcs3 c 254 3 + +Using mknod to manually create the device entries makes these device nodes +persistent. Once created they will exist prior to the driver insmod. + +Attempting to connect an application to /dev/hvcs* prior to insertion of +the hvcs module will result in an error message similar to the following: + + "/dev/hvcs*: No such device". + +NOTE: Just because there is a device node present doesn't mean that there +is a vty-server device configured for that node. + +--------------------------------------------------------------------------- +5. Connection + +Since this driver controls devices that provide a tty interface a user can +interact with the device node entries using any standard tty-interactive +method (e.g. "cat", "dd", "echo"). The intent of this driver however, is +to provide real time console interaction with a Linux partition's console, +which requires the use of applications that provide bi-directional, +interactive I/O with a tty device. + +Applications (e.g. "minicom" and "screen") that act as terminal emulators +or perform terminal type control sequence conversion on the data being +passed through them are NOT acceptable for providing interactive console +I/O. These programs often emulate antiquated terminal types (vt100 and +ANSI) and expect inbound data to take the form of one of these supported +terminal types but they either do not convert, or do not _adequately_ +convert, outbound data into the terminal type of the terminal which invoked +them (though screen makes an attempt and can apparently be configured with +much termcap wrestling.) + +For this reason kermit and cu are two of the recommended applications for +interacting with a Linux console via an hvcs device. These programs simply +act as a conduit for data transfer to and from the tty device. They do not +require inbound data to take the form of a particular terminal type, nor do +they cook outbound data to a particular terminal type. + +In order to ensure proper functioning of console applications one must make +sure that once connected to a /dev/hvcs console that the console's $TERM +env variable is set to the exact terminal type of the terminal emulator +used to launch the interactive I/O application. If one is using xterm and +kermit to connect to /dev/hvcs0 when the console prompt becomes available +one should "export TERM=xterm" on the console. This tells ncurses +applications that are invoked from the console that they should output +control sequences that xterm can understand. + +As a precautionary measure an hvcs user should always "exit" from their +session before disconnecting an application such as kermit from the device +node. If this is not done, the next user to connect to the console will +continue using the previous user's logged in session which includes +using the $TERM variable that the previous user supplied. + +Hotplug add and remove of vty-server adapters affects which /dev/hvcs* node +is used to connect to each vty-server adapter. In order to determine which +vty-server adapter is associated with which /dev/hvcs* node a special sysfs +attribute has been added to each vty-server sysfs entry. This entry is +called "index" and showing it reveals an integer that refers to the +/dev/hvcs* entry to use to connect to that device. For instance cating the +index attribute of vty-server adapter 30000004 shows the following. + + Pow5:/sys/bus/vio/drivers/hvcs/30000004 # cat index + 2 + +This index of '2' means that in order to connect to vty-server adapter +30000004 the user should interact with /dev/hvcs2. + +It should be noted that due to the system hotplug I/O capabilities of a +system the /dev/hvcs* entry that interacts with a particular vty-server +adapter is not guaranteed to remain the same across system reboots. Look +in the Q & A section for more on this issue. + +--------------------------------------------------------------------------- +6. Disconnection + +As a security feature to prevent the delivery of stale data to an +unintended target the Power5 system firmware disables the fetching of data +and discards that data when a connection between a vty-server and a vty has +been severed. As an example, when a vty-server is immediately disconnected +from a vty following output of data to the vty the vty adapter may not have +enough time between when it received the data interrupt and when the +connection was severed to fetch the data from firmware before the fetch is +disabled by firmware. + +When hvcs is being used to serve consoles this behavior is not a huge issue +because the adapter stays connected for large amounts of time following +almost all data writes. When hvcs is being used as a tty conduit to tunnel +data between two partitions [see Q & A below] this is a huge problem +because the standard Linux behavior when cat'ing or dd'ing data to a device +is to open the tty, send the data, and then close the tty. If this driver +manually terminated vty-server connections on tty close this would close +the vty-server and vty connection before the target vty has had a chance to +fetch the data. + +Additionally, disconnecting a vty-server and vty only on module removal or +adapter removal is impractical because other vty-servers in other +partitions may require the usage of the target vty at any time. + +Due to this behavioral restriction disconnection of vty-servers from the +connected vty is a manual procedure using a write to a sysfs attribute +outlined below, on the other hand the initial vty-server connection to a +vty is established automatically by this driver. Manual vty-server +connection is never required. + +In order to terminate the connection between a vty-server and vty the +"vterm_state" sysfs attribute within each vty-server's sysfs entry is used. +Reading this attribute reveals the current connection state of the +vty-server adapter. A zero means that the vty-server is not connected to a +vty. A one indicates that a connection is active. + +Writing a '0' (zero) to the vterm_state attribute will disconnect the VTERM +connection between the vty-server and target vty ONLY if the vterm_state +previously read '1'. The write directive is ignored if the vterm_state +read '0' or if any value other than '0' was written to the vterm_state +attribute. The following example will show the method used for verifying +the vty-server connection status and disconnecting a vty-server connection. + + Pow5:/sys/bus/vio/drivers/hvcs/30000004 # cat vterm_state + 1 + + Pow5:/sys/bus/vio/drivers/hvcs/30000004 # echo 0 > vterm_state + + Pow5:/sys/bus/vio/drivers/hvcs/30000004 # cat vterm_state + 0 + +All vty-server connections are automatically terminated when the device is +hotplug removed and when the module is removed. + +--------------------------------------------------------------------------- +7. Configuration + +Each vty-server has a sysfs entry in the /sys/devices/vio directory, which +is symlinked in several other sysfs tree directories, notably under the +hvcs driver entry, which looks like the following example: + + Pow5:/sys/bus/vio/drivers/hvcs # ls + . .. 30000003 30000004 rescan + +By design, firmware notifies the hvcs driver of vty-server lifetimes and +partner vty removals but not the addition of partner vtys. Since an HMC +Super Admin can add partner info dynamically we have provided the hvcs +driver sysfs directory with the "rescan" update attribute which will query +firmware and update the partner info for all the vty-servers that this +driver manages. Writing a '1' to the attribute triggers the update. An +explicit example follows: + + Pow5:/sys/bus/vio/drivers/hvcs # echo 1 > rescan + +Reading the attribute will indicate a state of '1' or '0'. A one indicates +that an update is in process. A zero indicates that an update has +completed or was never executed. + +Vty-server entries in this directory are a 32 bit partition unique unit +address that is created by firmware. An example vty-server sysfs entry +looks like the following: + + Pow5:/sys/bus/vio/drivers/hvcs/30000004 # ls + . current_vty devspec name partner_vtys + .. index partner_clcs vterm_state + +Each entry is provided, by default with a "name" attribute. Reading the +"name" attribute will reveal the device type as shown in the following +example: + + Pow5:/sys/bus/vio/drivers/hvcs/30000003 # cat name + vty-server + +Each entry is also provided, by default, with a "devspec" attribute which +reveals the full device specification when read, as shown in the following +example: + + Pow5:/sys/bus/vio/drivers/hvcs/30000004 # cat devspec + /vdevice/vty-server@30000004 + +Each vty-server sysfs dir is provided with two read-only attributes that +provide lists of easily parsed partner vty data: "partner_vtys" and +"partner_clcs". + + Pow5:/sys/bus/vio/drivers/hvcs/30000004 # cat partner_vtys + 30000000 + 30000001 + 30000002 + 30000000 + 30000000 + + Pow5:/sys/bus/vio/drivers/hvcs/30000004 # cat partner_clcs + U5112.428.103048A-V3-C0 + U5112.428.103048A-V3-C2 + U5112.428.103048A-V3-C3 + U5112.428.103048A-V4-C0 + U5112.428.103048A-V5-C0 + +Reading partner_vtys returns a list of partner vtys. Vty unit address +numbering is only per-partition-unique so entries will frequently repeat. + +Reading partner_clcs returns a list of "converged location codes" which are +composed of a system serial number followed by "-V*", where the '*' is the +target partition number, and "-C*", where the '*' is the slot of the +adapter. The first vty partner corresponds to the first clc item, the +second vty partner to the second clc item, etc. + +A vty-server can only be connected to a single vty at a time. The entry, +"current_vty" prints the clc of the currently selected partner vty when +read. + +The current_vty can be changed by writing a valid partner clc to the entry +as in the following example: + + Pow5:/sys/bus/vio/drivers/hvcs/30000004 # echo U5112.428.10304 + 8A-V4-C0 > current_vty + +Changing the current_vty when a vty-server is already connected to a vty +does not affect the current connection. The change takes effect when the +currently open connection is freed. + +Information on the "vterm_state" attribute was covered earlier on the +chapter entitled "disconnection". + +--------------------------------------------------------------------------- +8. Questions & Answers: +=========================================================================== +Q: What are the security concerns involving hvcs? + +A: There are three main security concerns: + + 1. The creator of the /dev/hvcs* nodes has the ability to restrict + the access of the device entries to certain users or groups. It + may be best to create a special hvcs group privilege for providing + access to system consoles. + + 2. To provide network security when grabbing the console it is + suggested that the user connect to the console hosting partition + using a secure method, such as SSH or sit at a hardware console. + + 3. Make sure to exit the user session when done with a console or + the next vty-server connection (which may be from another + partition) will experience the previously logged in session. + +--------------------------------------------------------------------------- +Q: How do I multiplex a console that I grab through hvcs so that other +people can see it: + +A: You can use "screen" to directly connect to the /dev/hvcs* device and +setup a session on your machine with the console group privileges. As +pointed out earlier by default screen doesn't provide the termcap settings +for most terminal emulators to provide adequate character conversion from +term type "screen" to others. This means that curses based programs may +not display properly in screen sessions. + +--------------------------------------------------------------------------- +Q: Why are the colors all messed up? +Q: Why are the control characters acting strange or not working? +Q: Why is the console output all strange and unintelligible? + +A: Please see the preceding section on "Connection" for a discussion of how +applications can affect the display of character control sequences. +Additionally, just because you logged into the console using and xterm +doesn't mean someone else didn't log into the console with the HMC console +(vt320) before you and leave the session logged in. The best thing to do +is to export TERM to the terminal type of your terminal emulator when you +get the console. Additionally make sure to "exit" the console before you +disconnect from the console. This will ensure that the next user gets +their own TERM type set when they login. + +--------------------------------------------------------------------------- +Q: When I try to CONNECT kermit to an hvcs device I get: +"Sorry, can't open connection: /dev/hvcs*"What is happening? + +A: Some other Power5 console mechanism has a connection to the vty and +isn't giving it up. You can try to force disconnect the consoles from the +HMC by right clicking on the partition and then selecting "close terminal". +Otherwise you have to hunt down the people who have console authority. It +is possible that you already have the console open using another kermit +session and just forgot about it. Please review the console options for +Power5 systems to determine the many ways a system console can be held. + +OR + +A: Another user may not have a connectivity method currently attached to a +/dev/hvcs device but the vterm_state may reveal that they still have the +vty-server connection established. They need to free this using the method +outlined in the section on "Disconnection" in order for others to connect +to the target vty. + +OR + +A: The user profile you are using to execute kermit probably doesn't have +permissions to use the /dev/hvcs* device. + +OR + +A: You probably haven't inserted the hvcs.ko module yet but the /dev/hvcs* +entry still exists (on systems without udev). + +OR + +A: There is not a corresponding vty-server device that maps to an existing +/dev/hvcs* entry. + +--------------------------------------------------------------------------- +Q: When I try to CONNECT kermit to an hvcs device I get: +"Sorry, write access to UUCP lockfile directory denied." + +A: The /dev/hvcs* entry you have specified doesn't exist where you said it +does? Maybe you haven't inserted the module (on systems with udev). + +--------------------------------------------------------------------------- +Q: If I already have one Linux partition installed can I use hvcs on said +partition to provide the console for the install of a second Linux +partition? + +A: Yes granted that your are connected to the /dev/hvcs* device using +kermit or cu or some other program that doesn't provide terminal emulation. + +--------------------------------------------------------------------------- +Q: Can I connect to more than one partition's console at a time using this +driver? + +A: Yes. Of course this means that there must be more than one vty-server +configured for this partition and each must point to a disconnected vty. + +--------------------------------------------------------------------------- +Q: Does the hvcs driver support dynamic (hotplug) addition of devices? + +A: Yes, if you have dlpar and hotplug enabled for your system and it has +been built into the kernel the hvcs drivers is configured to dynamically +handle additions of new devices and removals of unused devices. + +--------------------------------------------------------------------------- +Q: For some reason /dev/hvcs* doesn't map to the same vty-server adapter +after a reboot. What happened? + +A: Assignment of vty-server adapters to /dev/hvcs* entries is always done +in the order that the adapters are exposed. Due to hotplug capabilities of +this driver assignment of hotplug added vty-servers may be in a different +order than how they would be exposed on module load. Rebooting or +reloading the module after dynamic addition may result in the /dev/hvcs* +and vty-server coupling changing if a vty-server adapter was added in a +slot between two other vty-server adapters. Refer to the section above +on how to determine which vty-server goes with which /dev/hvcs* node. +Hint; look at the sysfs "index" attribute for the vty-server. + +--------------------------------------------------------------------------- +Q: Can I use /dev/hvcs* as a conduit to another partition and use a tty +device on that partition as the other end of the pipe? + +A: Yes, on Power5 platforms the hvc_console driver provides a tty interface +for extra /dev/hvc* devices (where /dev/hvc0 is most likely the console). +In order to get a tty conduit working between the two partitions the HMC +Super Admin must create an additional "serial server" for the target +partition with the HMC gui which will show up as /dev/hvc* when the target +partition is rebooted. + +The HMC Super Admin then creates an additional "serial client" for the +current partition and points this at the target partition's newly created +"serial server" adapter (remember the slot). This shows up as an +additional /dev/hvcs* device. + +Now a program on the target system can be configured to read or write to +/dev/hvc* and another program on the current partition can be configured to +read or write to /dev/hvcs*. Now you have a tty conduit between two +partitions. + +--------------------------------------------------------------------------- +9. Reporting Bugs: + +The proper channel for reporting bugs is either through the Linux OS +distribution company that provided your OS or by posting issues to the +PowerPC development mailing list at: + +linuxppc-dev@lists.ozlabs.org + +This request is to provide a documented and searchable public exchange +of the problems and solutions surrounding this driver for the benefit of +all users. diff --git a/Documentation/powerpc/mpc52xx.txt b/Documentation/powerpc/mpc52xx.txt new file mode 100644 index 000000000..0d540a31e --- /dev/null +++ b/Documentation/powerpc/mpc52xx.txt @@ -0,0 +1,39 @@ +Linux 2.6.x on MPC52xx family +----------------------------- + +For the latest info, go to http://www.246tNt.com/mpc52xx/ + +To compile/use : + + - U-Boot: + # tftpboot 200000 uImage + => tftpboot 400000 pRamdisk + => bootm 200000 400000 + + - DBug: + # dn -i zImage.initrd.lite5200 + + +Some remarks : + - The port is named mpc52xxx, and config options are PPC_MPC52xx. The MGT5100 + is not supported, and I'm not sure anyone is interesting in working on it + so. I didn't took 5xxx because there's apparently a lot of 5xxx that have + nothing to do with the MPC5200. I also included the 'MPC' for the same + reason. + - Of course, I inspired myself from the 2.4 port. If you think I forgot to + mention you/your company in the copyright of some code, I'll correct it + ASAP. diff --git a/Documentation/powerpc/pci_iov_resource_on_powernv.txt b/Documentation/powerpc/pci_iov_resource_on_powernv.txt new file mode 100644 index 000000000..b55c5cd83 --- /dev/null +++ b/Documentation/powerpc/pci_iov_resource_on_powernv.txt @@ -0,0 +1,301 @@ +Wei Yang +Benjamin Herrenschmidt +Bjorn Helgaas +26 Aug 2014 + +This document describes the requirement from hardware for PCI MMIO resource +sizing and assignment on PowerKVM and how generic PCI code handles this +requirement. The first two sections describe the concepts of Partitionable +Endpoints and the implementation on P8 (IODA2). The next two sections talks +about considerations on enabling SRIOV on IODA2. + +1. Introduction to Partitionable Endpoints + +A Partitionable Endpoint (PE) is a way to group the various resources +associated with a device or a set of devices to provide isolation between +partitions (i.e., filtering of DMA, MSIs etc.) and to provide a mechanism +to freeze a device that is causing errors in order to limit the possibility +of propagation of bad data. + +There is thus, in HW, a table of PE states that contains a pair of "frozen" +state bits (one for MMIO and one for DMA, they get set together but can be +cleared independently) for each PE. + +When a PE is frozen, all stores in any direction are dropped and all loads +return all 1's value. MSIs are also blocked. There's a bit more state that +captures things like the details of the error that caused the freeze etc., but +that's not critical. + +The interesting part is how the various PCIe transactions (MMIO, DMA, ...) +are matched to their corresponding PEs. + +The following section provides a rough description of what we have on P8 +(IODA2). Keep in mind that this is all per PHB (PCI host bridge). Each PHB +is a completely separate HW entity that replicates the entire logic, so has +its own set of PEs, etc. + +2. Implementation of Partitionable Endpoints on P8 (IODA2) + +P8 supports up to 256 Partitionable Endpoints per PHB. + + * Inbound + + For DMA, MSIs and inbound PCIe error messages, we have a table (in + memory but accessed in HW by the chip) that provides a direct + correspondence between a PCIe RID (bus/dev/fn) with a PE number. + We call this the RTT. + + - For DMA we then provide an entire address space for each PE that can + contain two "windows", depending on the value of PCI address bit 59. + Each window can be configured to be remapped via a "TCE table" (IOMMU + translation table), which has various configurable characteristics + not described here. + + - For MSIs, we have two windows in the address space (one at the top of + the 32-bit space and one much higher) which, via a combination of the + address and MSI value, will result in one of the 2048 interrupts per + bridge being triggered. There's a PE# in the interrupt controller + descriptor table as well which is compared with the PE# obtained from + the RTT to "authorize" the device to emit that specific interrupt. + + - Error messages just use the RTT. + + * Outbound. That's where the tricky part is. + + Like other PCI host bridges, the Power8 IODA2 PHB supports "windows" + from the CPU address space to the PCI address space. There is one M32 + window and sixteen M64 windows. They have different characteristics. + First what they have in common: they forward a configurable portion of + the CPU address space to the PCIe bus and must be naturally aligned + power of two in size. The rest is different: + + - The M32 window: + + * Is limited to 4GB in size. + + * Drops the top bits of the address (above the size) and replaces + them with a configurable value. This is typically used to generate + 32-bit PCIe accesses. We configure that window at boot from FW and + don't touch it from Linux; it's usually set to forward a 2GB + portion of address space from the CPU to PCIe + 0x8000_0000..0xffff_ffff. (Note: The top 64KB are actually + reserved for MSIs but this is not a problem at this point; we just + need to ensure Linux doesn't assign anything there, the M32 logic + ignores that however and will forward in that space if we try). + + * It is divided into 256 segments of equal size. A table in the chip + maps each segment to a PE#. That allows portions of the MMIO space + to be assigned to PEs on a segment granularity. For a 2GB window, + the segment granularity is 2GB/256 = 8MB. + + Now, this is the "main" window we use in Linux today (excluding + SR-IOV). We basically use the trick of forcing the bridge MMIO windows + onto a segment alignment/granularity so that the space behind a bridge + can be assigned to a PE. + + Ideally we would like to be able to have individual functions in PEs + but that would mean using a completely different address allocation + scheme where individual function BARs can be "grouped" to fit in one or + more segments. + + - The M64 windows: + + * Must be at least 256MB in size. + + * Do not translate addresses (the address on PCIe is the same as the + address on the PowerBus). There is a way to also set the top 14 + bits which are not conveyed by PowerBus but we don't use this. + + * Can be configured to be segmented. When not segmented, we can + specify the PE# for the entire window. When segmented, a window + has 256 segments; however, there is no table for mapping a segment + to a PE#. The segment number *is* the PE#. + + * Support overlaps. If an address is covered by multiple windows, + there's a defined ordering for which window applies. + + We have code (fairly new compared to the M32 stuff) that exploits that + for large BARs in 64-bit space: + + We configure an M64 window to cover the entire region of address space + that has been assigned by FW for the PHB (about 64GB, ignore the space + for the M32, it comes out of a different "reserve"). We configure it + as segmented. + + Then we do the same thing as with M32, using the bridge alignment + trick, to match to those giant segments. + + Since we cannot remap, we have two additional constraints: + + - We do the PE# allocation *after* the 64-bit space has been assigned + because the addresses we use directly determine the PE#. We then + update the M32 PE# for the devices that use both 32-bit and 64-bit + spaces or assign the remaining PE# to 32-bit only devices. + + - We cannot "group" segments in HW, so if a device ends up using more + than one segment, we end up with more than one PE#. There is a HW + mechanism to make the freeze state cascade to "companion" PEs but + that only works for PCIe error messages (typically used so that if + you freeze a switch, it freezes all its children). So we do it in + SW. We lose a bit of effectiveness of EEH in that case, but that's + the best we found. So when any of the PEs freezes, we freeze the + other ones for that "domain". We thus introduce the concept of + "master PE" which is the one used for DMA, MSIs, etc., and "secondary + PEs" that are used for the remaining M64 segments. + + We would like to investigate using additional M64 windows in "single + PE" mode to overlay over specific BARs to work around some of that, for + example for devices with very large BARs, e.g., GPUs. It would make + sense, but we haven't done it yet. + +3. Considerations for SR-IOV on PowerKVM + + * SR-IOV Background + + The PCIe SR-IOV feature allows a single Physical Function (PF) to + support several Virtual Functions (VFs). Registers in the PF's SR-IOV + Capability control the number of VFs and whether they are enabled. + + When VFs are enabled, they appear in Configuration Space like normal + PCI devices, but the BARs in VF config space headers are unusual. For + a non-VF device, software uses BARs in the config space header to + discover the BAR sizes and assign addresses for them. For VF devices, + software uses VF BAR registers in the *PF* SR-IOV Capability to + discover sizes and assign addresses. The BARs in the VF's config space + header are read-only zeros. + + When a VF BAR in the PF SR-IOV Capability is programmed, it sets the + base address for all the corresponding VF(n) BARs. For example, if the + PF SR-IOV Capability is programmed to enable eight VFs, and it has a + 1MB VF BAR0, the address in that VF BAR sets the base of an 8MB region. + This region is divided into eight contiguous 1MB regions, each of which + is a BAR0 for one of the VFs. Note that even though the VF BAR + describes an 8MB region, the alignment requirement is for a single VF, + i.e., 1MB in this example. + + There are several strategies for isolating VFs in PEs: + + - M32 window: There's one M32 window, and it is split into 256 + equally-sized segments. The finest granularity possible is a 256MB + window with 1MB segments. VF BARs that are 1MB or larger could be + mapped to separate PEs in this window. Each segment can be + individually mapped to a PE via the lookup table, so this is quite + flexible, but it works best when all the VF BARs are the same size. If + they are different sizes, the entire window has to be small enough that + the segment size matches the smallest VF BAR, which means larger VF + BARs span several segments. + + - Non-segmented M64 window: A non-segmented M64 window is mapped entirely + to a single PE, so it could only isolate one VF. + + - Single segmented M64 windows: A segmented M64 window could be used just + like the M32 window, but the segments can't be individually mapped to + PEs (the segment number is the PE#), so there isn't as much + flexibility. A VF with multiple BARs would have to be in a "domain" of + multiple PEs, which is not as well isolated as a single PE. + + - Multiple segmented M64 windows: As usual, each window is split into 256 + equally-sized segments, and the segment number is the PE#. But if we + use several M64 windows, they can be set to different base addresses + and different segment sizes. If we have VFs that each have a 1MB BAR + and a 32MB BAR, we could use one M64 window to assign 1MB segments and + another M64 window to assign 32MB segments. + + Finally, the plan to use M64 windows for SR-IOV, which will be described + more in the next two sections. For a given VF BAR, we need to + effectively reserve the entire 256 segments (256 * VF BAR size) and + position the VF BAR to start at the beginning of a free range of + segments/PEs inside that M64 window. + + The goal is of course to be able to give a separate PE for each VF. + + The IODA2 platform has 16 M64 windows, which are used to map MMIO + range to PE#. Each M64 window defines one MMIO range and this range is + divided into 256 segments, with each segment corresponding to one PE. + + We decide to leverage this M64 window to map VFs to individual PEs, since + SR-IOV VF BARs are all the same size. + + But doing so introduces another problem: total_VFs is usually smaller + than the number of M64 window segments, so if we map one VF BAR directly + to one M64 window, some part of the M64 window will map to another + device's MMIO range. + + IODA supports 256 PEs, so segmented windows contain 256 segments, so if + total_VFs is less than 256, we have the situation in Figure 1.0, where + segments [total_VFs, 255] of the M64 window may map to some MMIO range on + other devices: + + 0 1 total_VFs - 1 + +------+------+- -+------+------+ + | | | ... | | | + +------+------+- -+------+------+ + + VF(n) BAR space + + 0 1 total_VFs - 1 255 + +------+------+- -+------+------+- -+------+------+ + | | | ... | | | ... | | | + +------+------+- -+------+------+- -+------+------+ + + M64 window + + Figure 1.0 Direct map VF(n) BAR space + + Our current solution is to allocate 256 segments even if the VF(n) BAR + space doesn't need that much, as shown in Figure 1.1: + + 0 1 total_VFs - 1 255 + +------+------+- -+------+------+- -+------+------+ + | | | ... | | | ... | | | + +------+------+- -+------+------+- -+------+------+ + + VF(n) BAR space + extra + + 0 1 total_VFs - 1 255 + +------+------+- -+------+------+- -+------+------+ + | | | ... | | | ... | | | + +------+------+- -+------+------+- -+------+------+ + + M64 window + + Figure 1.1 Map VF(n) BAR space + extra + + Allocating the extra space ensures that the entire M64 window will be + assigned to this one SR-IOV device and none of the space will be + available for other devices. Note that this only expands the space + reserved in software; there are still only total_VFs VFs, and they only + respond to segments [0, total_VFs - 1]. There's nothing in hardware that + responds to segments [total_VFs, 255]. + +4. Implications for the Generic PCI Code + +The PCIe SR-IOV spec requires that the base of the VF(n) BAR space be +aligned to the size of an individual VF BAR. + +In IODA2, the MMIO address determines the PE#. If the address is in an M32 +window, we can set the PE# by updating the table that translates segments +to PE#s. Similarly, if the address is in an unsegmented M64 window, we can +set the PE# for the window. But if it's in a segmented M64 window, the +segment number is the PE#. + +Therefore, the only way to control the PE# for a VF is to change the base +of the VF(n) BAR space in the VF BAR. If the PCI core allocates the exact +amount of space required for the VF(n) BAR space, the VF BAR value is fixed +and cannot be changed. + +On the other hand, if the PCI core allocates additional space, the VF BAR +value can be changed as long as the entire VF(n) BAR space remains inside +the space allocated by the core. + +Ideally the segment size will be the same as an individual VF BAR size. +Then each VF will be in its own PE. The VF BARs (and therefore the PE#s) +are contiguous. If VF0 is in PE(x), then VF(n) is in PE(x+n). If we +allocate 256 segments, there are (256 - numVFs) choices for the PE# of VF0. + +If the segment size is smaller than the VF BAR size, it will take several +segments to cover a VF BAR, and a VF will be in several PEs. This is +possible, but the isolation isn't as good, and it reduces the number of PE# +choices because instead of consuming only numVFs segments, the VF(n) BAR +space will consume (numVFs * n) segments. That means there aren't as many +available segments for adjusting base of the VF(n) BAR space. diff --git a/Documentation/powerpc/pmu-ebb.txt b/Documentation/powerpc/pmu-ebb.txt new file mode 100644 index 000000000..73cd163db --- /dev/null +++ b/Documentation/powerpc/pmu-ebb.txt @@ -0,0 +1,137 @@ +PMU Event Based Branches +======================== + +Event Based Branches (EBBs) are a feature which allows the hardware to +branch directly to a specified user space address when certain events occur. + +The full specification is available in Power ISA v2.07: + + https://www.power.org/documentation/power-isa-version-2-07/ + +One type of event for which EBBs can be configured is PMU exceptions. This +document describes the API for configuring the Power PMU to generate EBBs, +using the Linux perf_events API. + + +Terminology +----------- + +Throughout this document we will refer to an "EBB event" or "EBB events". This +just refers to a struct perf_event which has set the "EBB" flag in its +attr.config. All events which can be configured on the hardware PMU are +possible "EBB events". + + +Background +---------- + +When a PMU EBB occurs it is delivered to the currently running process. As such +EBBs can only sensibly be used by programs for self-monitoring. + +It is a feature of the perf_events API that events can be created on other +processes, subject to standard permission checks. This is also true of EBB +events, however unless the target process enables EBBs (via mtspr(BESCR)) no +EBBs will ever be delivered. + +This makes it possible for a process to enable EBBs for itself, but not +actually configure any events. At a later time another process can come along +and attach an EBB event to the process, which will then cause EBBs to be +delivered to the first process. It's not clear if this is actually useful. + + +When the PMU is configured for EBBs, all PMU interrupts are delivered to the +user process. This means once an EBB event is scheduled on the PMU, no non-EBB +events can be configured. This means that EBB events can not be run +concurrently with regular 'perf' commands, or any other perf events. + +It is however safe to run 'perf' commands on a process which is using EBBs. The +kernel will in general schedule the EBB event, and perf will be notified that +its events could not run. + +The exclusion between EBB events and regular events is implemented using the +existing "pinned" and "exclusive" attributes of perf_events. This means EBB +events will be given priority over other events, unless they are also pinned. +If an EBB event and a regular event are both pinned, then whichever is enabled +first will be scheduled and the other will be put in error state. See the +section below titled "Enabling an EBB event" for more information. + + +Creating an EBB event +--------------------- + +To request that an event is counted using EBB, the event code should have bit +63 set. + +EBB events must be created with a particular, and restrictive, set of +attributes - this is so that they interoperate correctly with the rest of the +perf_events subsystem. + +An EBB event must be created with the "pinned" and "exclusive" attributes set. +Note that if you are creating a group of EBB events, only the leader can have +these attributes set. + +An EBB event must NOT set any of the "inherit", "sample_period", "freq" or +"enable_on_exec" attributes. + +An EBB event must be attached to a task. This is specified to perf_event_open() +by passing a pid value, typically 0 indicating the current task. + +All events in a group must agree on whether they want EBB. That is all events +must request EBB, or none may request EBB. + +EBB events must specify the PMC they are to be counted on. This ensures +userspace is able to reliably determine which PMC the event is scheduled on. + + +Enabling an EBB event +--------------------- + +Once an EBB event has been successfully opened, it must be enabled with the +perf_events API. This can be achieved either via the ioctl() interface, or the +prctl() interface. + +However, due to the design of the perf_events API, enabling an event does not +guarantee that it has been scheduled on the PMU. To ensure that the EBB event +has been scheduled on the PMU, you must perform a read() on the event. If the +read() returns EOF, then the event has not been scheduled and EBBs are not +enabled. + +This behaviour occurs because the EBB event is pinned and exclusive. When the +EBB event is enabled it will force all other non-pinned events off the PMU. In +this case the enable will be successful. However if there is already an event +pinned on the PMU then the enable will not be successful. + + +Reading an EBB event +-------------------- + +It is possible to read() from an EBB event. However the results are +meaningless. Because interrupts are being delivered to the user process the +kernel is not able to count the event, and so will return a junk value. + + +Closing an EBB event +-------------------- + +When an EBB event is finished with, you can close it using close() as for any +regular event. If this is the last EBB event the PMU will be deconfigured and +no further PMU EBBs will be delivered. + + +EBB Handler +----------- + +The EBB handler is just regular userspace code, however it must be written in +the style of an interrupt handler. When the handler is entered all registers +are live (possibly) and so must be saved somehow before the handler can invoke +other code. + +It's up to the program how to handle this. For C programs a relatively simple +option is to create an interrupt frame on the stack and save registers there. + +Fork +---- + +EBB events are not inherited across fork. If the child process wishes to use +EBBs it should open a new event for itself. Similarly the EBB state in +BESCR/EBBHR/EBBRR is cleared across fork(). diff --git a/Documentation/powerpc/ptrace.txt b/Documentation/powerpc/ptrace.txt new file mode 100644 index 000000000..99c5ce88d --- /dev/null +++ b/Documentation/powerpc/ptrace.txt @@ -0,0 +1,151 @@ +GDB intends to support the following hardware debug features of BookE +processors: + +4 hardware breakpoints (IAC) +2 hardware watchpoints (read, write and read-write) (DAC) +2 value conditions for the hardware watchpoints (DVC) + +For that, we need to extend ptrace so that GDB can query and set these +resources. Since we're extending, we're trying to create an interface +that's extendable and that covers both BookE and server processors, so +that GDB doesn't need to special-case each of them. We added the +following 3 new ptrace requests. + +1. PTRACE_PPC_GETHWDEBUGINFO + +Query for GDB to discover the hardware debug features. The main info to +be returned here is the minimum alignment for the hardware watchpoints. +BookE processors don't have restrictions here, but server processors have +an 8-byte alignment restriction for hardware watchpoints. We'd like to avoid +adding special cases to GDB based on what it sees in AUXV. + +Since we're at it, we added other useful info that the kernel can return to +GDB: this query will return the number of hardware breakpoints, hardware +watchpoints and whether it supports a range of addresses and a condition. +The query will fill the following structure provided by the requesting process: + +struct ppc_debug_info { + unit32_t version; + unit32_t num_instruction_bps; + unit32_t num_data_bps; + unit32_t num_condition_regs; + unit32_t data_bp_alignment; + unit32_t sizeof_condition; /* size of the DVC register */ + uint64_t features; /* bitmask of the individual flags */ +}; + +features will have bits indicating whether there is support for: + +#define PPC_DEBUG_FEATURE_INSN_BP_RANGE 0x1 +#define PPC_DEBUG_FEATURE_INSN_BP_MASK 0x2 +#define PPC_DEBUG_FEATURE_DATA_BP_RANGE 0x4 +#define PPC_DEBUG_FEATURE_DATA_BP_MASK 0x8 +#define PPC_DEBUG_FEATURE_DATA_BP_DAWR 0x10 + +2. PTRACE_SETHWDEBUG + +Sets a hardware breakpoint or watchpoint, according to the provided structure: + +struct ppc_hw_breakpoint { + uint32_t version; +#define PPC_BREAKPOINT_TRIGGER_EXECUTE 0x1 +#define PPC_BREAKPOINT_TRIGGER_READ 0x2 +#define PPC_BREAKPOINT_TRIGGER_WRITE 0x4 + uint32_t trigger_type; /* only some combinations allowed */ +#define PPC_BREAKPOINT_MODE_EXACT 0x0 +#define PPC_BREAKPOINT_MODE_RANGE_INCLUSIVE 0x1 +#define PPC_BREAKPOINT_MODE_RANGE_EXCLUSIVE 0x2 +#define PPC_BREAKPOINT_MODE_MASK 0x3 + uint32_t addr_mode; /* address match mode */ + +#define PPC_BREAKPOINT_CONDITION_MODE 0x3 +#define PPC_BREAKPOINT_CONDITION_NONE 0x0 +#define PPC_BREAKPOINT_CONDITION_AND 0x1 +#define PPC_BREAKPOINT_CONDITION_EXACT 0x1 /* different name for the same thing as above */ +#define PPC_BREAKPOINT_CONDITION_OR 0x2 +#define PPC_BREAKPOINT_CONDITION_AND_OR 0x3 +#define PPC_BREAKPOINT_CONDITION_BE_ALL 0x00ff0000 /* byte enable bits */ +#define PPC_BREAKPOINT_CONDITION_BE(n) (1<<((n)+16)) + uint32_t condition_mode; /* break/watchpoint condition flags */ + + uint64_t addr; + uint64_t addr2; + uint64_t condition_value; +}; + +A request specifies one event, not necessarily just one register to be set. +For instance, if the request is for a watchpoint with a condition, both the +DAC and DVC registers will be set in the same request. + +With this GDB can ask for all kinds of hardware breakpoints and watchpoints +that the BookE supports. COMEFROM breakpoints available in server processors +are not contemplated, but that is out of the scope of this work. + +ptrace will return an integer (handle) uniquely identifying the breakpoint or +watchpoint just created. This integer will be used in the PTRACE_DELHWDEBUG +request to ask for its removal. Return -ENOSPC if the requested breakpoint +can't be allocated on the registers. + +Some examples of using the structure to: + +- set a breakpoint in the first breakpoint register + + p.version = PPC_DEBUG_CURRENT_VERSION; + p.trigger_type = PPC_BREAKPOINT_TRIGGER_EXECUTE; + p.addr_mode = PPC_BREAKPOINT_MODE_EXACT; + p.condition_mode = PPC_BREAKPOINT_CONDITION_NONE; + p.addr = (uint64_t) address; + p.addr2 = 0; + p.condition_value = 0; + +- set a watchpoint which triggers on reads in the second watchpoint register + + p.version = PPC_DEBUG_CURRENT_VERSION; + p.trigger_type = PPC_BREAKPOINT_TRIGGER_READ; + p.addr_mode = PPC_BREAKPOINT_MODE_EXACT; + p.condition_mode = PPC_BREAKPOINT_CONDITION_NONE; + p.addr = (uint64_t) address; + p.addr2 = 0; + p.condition_value = 0; + +- set a watchpoint which triggers only with a specific value + + p.version = PPC_DEBUG_CURRENT_VERSION; + p.trigger_type = PPC_BREAKPOINT_TRIGGER_READ; + p.addr_mode = PPC_BREAKPOINT_MODE_EXACT; + p.condition_mode = PPC_BREAKPOINT_CONDITION_AND | PPC_BREAKPOINT_CONDITION_BE_ALL; + p.addr = (uint64_t) address; + p.addr2 = 0; + p.condition_value = (uint64_t) condition; + +- set a ranged hardware breakpoint + + p.version = PPC_DEBUG_CURRENT_VERSION; + p.trigger_type = PPC_BREAKPOINT_TRIGGER_EXECUTE; + p.addr_mode = PPC_BREAKPOINT_MODE_RANGE_INCLUSIVE; + p.condition_mode = PPC_BREAKPOINT_CONDITION_NONE; + p.addr = (uint64_t) begin_range; + p.addr2 = (uint64_t) end_range; + p.condition_value = 0; + +- set a watchpoint in server processors (BookS) + + p.version = 1; + p.trigger_type = PPC_BREAKPOINT_TRIGGER_RW; + p.addr_mode = PPC_BREAKPOINT_MODE_RANGE_INCLUSIVE; + or + p.addr_mode = PPC_BREAKPOINT_MODE_EXACT; + + p.condition_mode = PPC_BREAKPOINT_CONDITION_NONE; + p.addr = (uint64_t) begin_range; + /* For PPC_BREAKPOINT_MODE_RANGE_INCLUSIVE addr2 needs to be specified, where + * addr2 - addr <= 8 Bytes. + */ + p.addr2 = (uint64_t) end_range; + p.condition_value = 0; + +3. PTRACE_DELHWDEBUG + +Takes an integer which identifies an existing breakpoint or watchpoint +(i.e., the value returned from PTRACE_SETHWDEBUG), and deletes the +corresponding breakpoint or watchpoint.. diff --git a/Documentation/powerpc/qe_firmware.txt b/Documentation/powerpc/qe_firmware.txt new file mode 100644 index 000000000..e7ac24aec --- /dev/null +++ b/Documentation/powerpc/qe_firmware.txt @@ -0,0 +1,295 @@ + Freescale QUICC Engine Firmware Uploading + ----------------------------------------- + +(c) 2007 Timur Tabi , + Freescale Semiconductor + +Table of Contents +================= + + I - Software License for Firmware + + II - Microcode Availability + + III - Description and Terminology + + IV - Microcode Programming Details + + V - Firmware Structure Layout + + VI - Sample Code for Creating Firmware Files + +Revision Information +==================== + +November 30, 2007: Rev 1.0 - Initial version + +I - Software License for Firmware +================================= + +Each firmware file comes with its own software license. For information on +the particular license, please see the license text that is distributed with +the firmware. + +II - Microcode Availability +=========================== + +Firmware files are distributed through various channels. Some are available on +http://opensource.freescale.com. For other firmware files, please contact +your Freescale representative or your operating system vendor. + +III - Description and Terminology +================================ + +In this document, the term 'microcode' refers to the sequence of 32-bit +integers that compose the actual QE microcode. + +The term 'firmware' refers to a binary blob that contains the microcode as +well as other data that + + 1) describes the microcode's purpose + 2) describes how and where to upload the microcode + 3) specifies the values of various registers + 4) includes additional data for use by specific device drivers + +Firmware files are binary files that contain only a firmware. + +IV - Microcode Programming Details +=================================== + +The QE architecture allows for only one microcode present in I-RAM for each +RISC processor. To replace any current microcode, a full QE reset (which +disables the microcode) must be performed first. + +QE microcode is uploaded using the following procedure: + +1) The microcode is placed into I-RAM at a specific location, using the + IRAM.IADD and IRAM.IDATA registers. + +2) The CERCR.CIR bit is set to 0 or 1, depending on whether the firmware + needs split I-RAM. Split I-RAM is only meaningful for SOCs that have + QEs with multiple RISC processors, such as the 8360. Splitting the I-RAM + allows each processor to run a different microcode, effectively creating an + asymmetric multiprocessing (AMP) system. + +3) The TIBCR trap registers are loaded with the addresses of the trap handlers + in the microcode. + +4) The RSP.ECCR register is programmed with the value provided. + +5) If necessary, device drivers that need the virtual traps and extended mode + data will use them. + +Virtual Microcode Traps + +These virtual traps are conditional branches in the microcode. These are +"soft" provisional introduced in the ROMcode in order to enable higher +flexibility and save h/w traps If new features are activated or an issue is +being fixed in the RAM package utilizing they should be activated. This data +structure signals the microcode which of these virtual traps is active. + +This structure contains 6 words that the application should copy to some +specific been defined. This table describes the structure. + + --------------------------------------------------------------- + | Offset in | | Destination Offset | Size of | + | array | Protocol | within PRAM | Operand | + --------------------------------------------------------------| + | 0 | Ethernet | 0xF8 | 4 bytes | + | | interworking | | | + --------------------------------------------------------------- + | 4 | ATM | 0xF8 | 4 bytes | + | | interworking | | | + --------------------------------------------------------------- + | 8 | PPP | 0xF8 | 4 bytes | + | | interworking | | | + --------------------------------------------------------------- + | 12 | Ethernet RX | 0x22 | 1 byte | + | | Distributor Page | | | + --------------------------------------------------------------- + | 16 | ATM Globtal | 0x28 | 1 byte | + | | Params Table | | | + --------------------------------------------------------------- + | 20 | Insert Frame | 0xF8 | 4 bytes | + --------------------------------------------------------------- + + +Extended Modes + +This is a double word bit array (64 bits) that defines special functionality +which has an impact on the software drivers. Each bit has its own impact +and has special instructions for the s/w associated with it. This structure is +described in this table: + + ----------------------------------------------------------------------- + | Bit # | Name | Description | + ----------------------------------------------------------------------- + | 0 | General | Indicates that prior to each host command | + | | push command | given by the application, the software must | + | | | assert a special host command (push command)| + | | | CECDR = 0x00800000. | + | | | CECR = 0x01c1000f. | + ----------------------------------------------------------------------- + | 1 | UCC ATM | Indicates that after issuing ATM RX INIT | + | | RX INIT | command, the host must issue another special| + | | push command | command (push command) and immediately | + | | | following that re-issue the ATM RX INIT | + | | | command. (This makes the sequence of | + | | | initializing the ATM receiver a sequence of | + | | | three host commands) | + | | | CECDR = 0x00800000. | + | | | CECR = 0x01c1000f. | + ----------------------------------------------------------------------- + | 2 | Add/remove | Indicates that following the specific host | + | | command | command: "Add/Remove entry in Hash Lookup | + | | validation | Table" used in Interworking setup, the user | + | | | must issue another command. | + | | | CECDR = 0xce000003. | + | | | CECR = 0x01c10f58. | + ----------------------------------------------------------------------- + | 3 | General push | Indicates that the s/w has to initialize | + | | command | some pointers in the Ethernet thread pages | + | | | which are used when Header Compression is | + | | | activated. The full details of these | + | | | pointers is located in the software drivers.| + ----------------------------------------------------------------------- + | 4 | General push | Indicates that after issuing Ethernet TX | + | | command | INIT command, user must issue this command | + | | | for each SNUM of Ethernet TX thread. | + | | | CECDR = 0x00800003. | + | | | CECR = 0x7'b{0}, 8'b{Enet TX thread SNUM}, | + | | | 1'b{1}, 12'b{0}, 4'b{1} | + ----------------------------------------------------------------------- + | 5 - 31 | N/A | Reserved, set to zero. | + ----------------------------------------------------------------------- + +V - Firmware Structure Layout +============================== + +QE microcode from Freescale is typically provided as a header file. This +header file contains macros that define the microcode binary itself as well as +some other data used in uploading that microcode. The format of these files +do not lend themselves to simple inclusion into other code. Hence, +the need for a more portable format. This section defines that format. + +Instead of distributing a header file, the microcode and related data are +embedded into a binary blob. This blob is passed to the qe_upload_firmware() +function, which parses the blob and performs everything necessary to upload +the microcode. + +All integers are big-endian. See the comments for function +qe_upload_firmware() for up-to-date implementation information. + +This structure supports versioning, where the version of the structure is +embedded into the structure itself. To ensure forward and backwards +compatibility, all versions of the structure must use the same 'qe_header' +structure at the beginning. + +'header' (type: struct qe_header): + The 'length' field is the size, in bytes, of the entire structure, + including all the microcode embedded in it, as well as the CRC (if + present). + + The 'magic' field is an array of three bytes that contains the letters + 'Q', 'E', and 'F'. This is an identifier that indicates that this + structure is a QE Firmware structure. + + The 'version' field is a single byte that indicates the version of this + structure. If the layout of the structure should ever need to be + changed to add support for additional types of microcode, then the + version number should also be changed. + +The 'id' field is a null-terminated string(suitable for printing) that +identifies the firmware. + +The 'count' field indicates the number of 'microcode' structures. There +must be one and only one 'microcode' structure for each RISC processor. +Therefore, this field also represents the number of RISC processors for this +SOC. + +The 'soc' structure contains the SOC numbers and revisions used to match +the microcode to the SOC itself. Normally, the microcode loader should +check the data in this structure with the SOC number and revisions, and +only upload the microcode if there's a match. However, this check is not +made on all platforms. + +Although it is not recommended, you can specify '0' in the soc.model +field to skip matching SOCs altogether. + +The 'model' field is a 16-bit number that matches the actual SOC. The +'major' and 'minor' fields are the major and minor revision numbers, +respectively, of the SOC. + +For example, to match the 8323, revision 1.0: + soc.model = 8323 + soc.major = 1 + soc.minor = 0 + +'padding' is necessary for structure alignment. This field ensures that the +'extended_modes' field is aligned on a 64-bit boundary. + +'extended_modes' is a bitfield that defines special functionality which has an +impact on the device drivers. Each bit has its own impact and has special +instructions for the driver associated with it. This field is stored in +the QE library and available to any driver that calles qe_get_firmware_info(). + +'vtraps' is an array of 8 words that contain virtual trap values for each +virtual traps. As with 'extended_modes', this field is stored in the QE +library and available to any driver that calles qe_get_firmware_info(). + +'microcode' (type: struct qe_microcode): + For each RISC processor there is one 'microcode' structure. The first + 'microcode' structure is for the first RISC, and so on. + + The 'id' field is a null-terminated string suitable for printing that + identifies this particular microcode. + + 'traps' is an array of 16 words that contain hardware trap values + for each of the 16 traps. If trap[i] is 0, then this particular + trap is to be ignored (i.e. not written to TIBCR[i]). The entire value + is written as-is to the TIBCR[i] register, so be sure to set the EN + and T_IBP bits if necessary. + + 'eccr' is the value to program into the ECCR register. + + 'iram_offset' is the offset into IRAM to start writing the + microcode. + + 'count' is the number of 32-bit words in the microcode. + + 'code_offset' is the offset, in bytes, from the beginning of this + structure where the microcode itself can be found. The first + microcode binary should be located immediately after the 'microcode' + array. + + 'major', 'minor', and 'revision' are the major, minor, and revision + version numbers, respectively, of the microcode. If all values are 0, + then these fields are ignored. + + 'reserved' is necessary for structure alignment. Since 'microcode' + is an array, the 64-bit 'extended_modes' field needs to be aligned + on a 64-bit boundary, and this can only happen if the size of + 'microcode' is a multiple of 8 bytes. To ensure that, we add + 'reserved'. + +After the last microcode is a 32-bit CRC. It can be calculated using +this algorithm: + +u32 crc32(const u8 *p, unsigned int len) +{ + unsigned int i; + u32 crc = 0; + + while (len--) { + crc ^= *p++; + for (i = 0; i < 8; i++) + crc = (crc >> 1) ^ ((crc & 1) ? 0xedb88320 : 0); + } + return crc; +} + +VI - Sample Code for Creating Firmware Files +============================================ + +A Python program that creates firmware binaries from the header files normally +distributed by Freescale can be found on http://opensource.freescale.com. diff --git a/Documentation/powerpc/syscall64-abi.txt b/Documentation/powerpc/syscall64-abi.txt new file mode 100644 index 000000000..fa716a0d8 --- /dev/null +++ b/Documentation/powerpc/syscall64-abi.txt @@ -0,0 +1,105 @@ +=============================================== +Power Architecture 64-bit Linux system call ABI +=============================================== + +syscall +======= + +syscall calling sequence[*] matches the Power Architecture 64-bit ELF ABI +specification C function calling sequence, including register preservation +rules, with the following differences. + +[*] Some syscalls (typically low-level management functions) may have + different calling sequences (e.g., rt_sigreturn). + +Parameters and return value +--------------------------- +The system call number is specified in r0. + +There is a maximum of 6 integer parameters to a syscall, passed in r3-r8. + +Both a return value and a return error code are returned. cr0.SO is the return +error code, and r3 is the return value or error code. When cr0.SO is clear, +the syscall succeeded and r3 is the return value. When cr0.SO is set, the +syscall failed and r3 is the error code that generally corresponds to errno. + +Stack +----- +System calls do not modify the caller's stack frame. For example, the caller's +stack frame LR and CR save fields are not used. + +Register preservation rules +--------------------------- +Register preservation rules match the ELF ABI calling sequence with the +following differences: + +r0: Volatile. (System call number.) +r3: Volatile. (Parameter 1, and return value.) +r4-r8: Volatile. (Parameters 2-6.) +cr0: Volatile (cr0.SO is the return error condition) +cr1, cr5-7: Nonvolatile. +lr: Nonvolatile. + +All floating point and vector data registers as well as control and status +registers are nonvolatile. + +Invocation +---------- +The syscall is performed with the sc instruction, and returns with execution +continuing at the instruction following the sc instruction. + +Transactional Memory +-------------------- +Syscall behavior can change if the processor is in transactional or suspended +transaction state, and the syscall can affect the behavior of the transaction. + +If the processor is in suspended state when a syscall is made, the syscall +will be performed as normal, and will return as normal. The syscall will be +performed in suspended state, so its side effects will be persistent according +to the usual transactional memory semantics. A syscall may or may not result +in the transaction being doomed by hardware. + +If the processor is in transactional state when a syscall is made, then the +behavior depends on the presence of PPC_FEATURE2_HTM_NOSC in the AT_HWCAP2 ELF +auxiliary vector. + +- If present, which is the case for newer kernels, then the syscall will not + be performed and the transaction will be doomed by the kernel with the + failure code TM_CAUSE_SYSCALL | TM_CAUSE_PERSISTENT in the TEXASR SPR. + +- If not present (older kernels), then the kernel will suspend the + transactional state and the syscall will proceed as in the case of a + suspended state syscall, and will resume the transactional state before + returning to the caller. This case is not well defined or supported, so this + behavior should not be relied upon. + + +vsyscall +======== + +vsyscall calling sequence matches the syscall calling sequence, with the +following differences. Some vsyscalls may have different calling sequences. + +Parameters and return value +--------------------------- +r0 is not used as an input. The vsyscall is selected by its address. + +Stack +----- +The vsyscall may or may not use the caller's stack frame save areas. + +Register preservation rules +--------------------------- +r0: Volatile. +cr1, cr5-7: Volatile. +lr: Volatile. + +Invocation +---------- +The vsyscall is performed with a branch-with-link instruction to the vsyscall +function address. + +Transactional Memory +-------------------- +vsyscalls will run in the same transactional state as the caller. A vsyscall +may or may not result in the transaction being doomed by hardware. diff --git a/Documentation/powerpc/transactional_memory.txt b/Documentation/powerpc/transactional_memory.txt new file mode 100644 index 000000000..52c023e14 --- /dev/null +++ b/Documentation/powerpc/transactional_memory.txt @@ -0,0 +1,244 @@ +Transactional Memory support +============================ + +POWER kernel support for this feature is currently limited to supporting +its use by user programs. It is not currently used by the kernel itself. + +This file aims to sum up how it is supported by Linux and what behaviour you +can expect from your user programs. + + +Basic overview +============== + +Hardware Transactional Memory is supported on POWER8 processors, and is a +feature that enables a different form of atomic memory access. Several new +instructions are presented to delimit transactions; transactions are +guaranteed to either complete atomically or roll back and undo any partial +changes. + +A simple transaction looks like this: + +begin_move_money: + tbegin + beq abort_handler + + ld r4, SAVINGS_ACCT(r3) + ld r5, CURRENT_ACCT(r3) + subi r5, r5, 1 + addi r4, r4, 1 + std r4, SAVINGS_ACCT(r3) + std r5, CURRENT_ACCT(r3) + + tend + + b continue + +abort_handler: + ... test for odd failures ... + + /* Retry the transaction if it failed because it conflicted with + * someone else: */ + b begin_move_money + + +The 'tbegin' instruction denotes the start point, and 'tend' the end point. +Between these points the processor is in 'Transactional' state; any memory +references will complete in one go if there are no conflicts with other +transactional or non-transactional accesses within the system. In this +example, the transaction completes as though it were normal straight-line code +IF no other processor has touched SAVINGS_ACCT(r3) or CURRENT_ACCT(r3); an +atomic move of money from the current account to the savings account has been +performed. Even though the normal ld/std instructions are used (note no +lwarx/stwcx), either *both* SAVINGS_ACCT(r3) and CURRENT_ACCT(r3) will be +updated, or neither will be updated. + +If, in the meantime, there is a conflict with the locations accessed by the +transaction, the transaction will be aborted by the CPU. Register and memory +state will roll back to that at the 'tbegin', and control will continue from +'tbegin+4'. The branch to abort_handler will be taken this second time; the +abort handler can check the cause of the failure, and retry. + +Checkpointed registers include all GPRs, FPRs, VRs/VSRs, LR, CCR/CR, CTR, FPCSR +and a few other status/flag regs; see the ISA for details. + +Causes of transaction aborts +============================ + +- Conflicts with cache lines used by other processors +- Signals +- Context switches +- See the ISA for full documentation of everything that will abort transactions. + + +Syscalls +======== + +Syscalls made from within an active transaction will not be performed and the +transaction will be doomed by the kernel with the failure code TM_CAUSE_SYSCALL +| TM_CAUSE_PERSISTENT. + +Syscalls made from within a suspended transaction are performed as normal and +the transaction is not explicitly doomed by the kernel. However, what the +kernel does to perform the syscall may result in the transaction being doomed +by the hardware. The syscall is performed in suspended mode so any side +effects will be persistent, independent of transaction success or failure. No +guarantees are provided by the kernel about which syscalls will affect +transaction success. + +Care must be taken when relying on syscalls to abort during active transactions +if the calls are made via a library. Libraries may cache values (which may +give the appearance of success) or perform operations that cause transaction +failure before entering the kernel (which may produce different failure codes). +Examples are glibc's getpid() and lazy symbol resolution. + + +Signals +======= + +Delivery of signals (both sync and async) during transactions provides a second +thread state (ucontext/mcontext) to represent the second transactional register +state. Signal delivery 'treclaim's to capture both register states, so signals +abort transactions. The usual ucontext_t passed to the signal handler +represents the checkpointed/original register state; the signal appears to have +arisen at 'tbegin+4'. + +If the sighandler ucontext has uc_link set, a second ucontext has been +delivered. For future compatibility the MSR.TS field should be checked to +determine the transactional state -- if so, the second ucontext in uc->uc_link +represents the active transactional registers at the point of the signal. + +For 64-bit processes, uc->uc_mcontext.regs->msr is a full 64-bit MSR and its TS +field shows the transactional mode. + +For 32-bit processes, the mcontext's MSR register is only 32 bits; the top 32 +bits are stored in the MSR of the second ucontext, i.e. in +uc->uc_link->uc_mcontext.regs->msr. The top word contains the transactional +state TS. + +However, basic signal handlers don't need to be aware of transactions +and simply returning from the handler will deal with things correctly: + +Transaction-aware signal handlers can read the transactional register state +from the second ucontext. This will be necessary for crash handlers to +determine, for example, the address of the instruction causing the SIGSEGV. + +Example signal handler: + + void crash_handler(int sig, siginfo_t *si, void *uc) + { + ucontext_t *ucp = uc; + ucontext_t *transactional_ucp = ucp->uc_link; + + if (ucp_link) { + u64 msr = ucp->uc_mcontext.regs->msr; + /* May have transactional ucontext! */ +#ifndef __powerpc64__ + msr |= ((u64)transactional_ucp->uc_mcontext.regs->msr) << 32; +#endif + if (MSR_TM_ACTIVE(msr)) { + /* Yes, we crashed during a transaction. Oops. */ + fprintf(stderr, "Transaction to be restarted at 0x%llx, but " + "crashy instruction was at 0x%llx\n", + ucp->uc_mcontext.regs->nip, + transactional_ucp->uc_mcontext.regs->nip); + } + } + + fix_the_problem(ucp->dar); + } + +When in an active transaction that takes a signal, we need to be careful with +the stack. It's possible that the stack has moved back up after the tbegin. +The obvious case here is when the tbegin is called inside a function that +returns before a tend. In this case, the stack is part of the checkpointed +transactional memory state. If we write over this non transactionally or in +suspend, we are in trouble because if we get a tm abort, the program counter and +stack pointer will be back at the tbegin but our in memory stack won't be valid +anymore. + +To avoid this, when taking a signal in an active transaction, we need to use +the stack pointer from the checkpointed state, rather than the speculated +state. This ensures that the signal context (written tm suspended) will be +written below the stack required for the rollback. The transaction is aborted +because of the treclaim, so any memory written between the tbegin and the +signal will be rolled back anyway. + +For signals taken in non-TM or suspended mode, we use the +normal/non-checkpointed stack pointer. + +Any transaction initiated inside a sighandler and suspended on return +from the sighandler to the kernel will get reclaimed and discarded. + +Failure cause codes used by kernel +================================== + +These are defined in , and distinguish different reasons why the +kernel aborted a transaction: + + TM_CAUSE_RESCHED Thread was rescheduled. + TM_CAUSE_TLBI Software TLB invalid. + TM_CAUSE_FAC_UNAV FP/VEC/VSX unavailable trap. + TM_CAUSE_SYSCALL Syscall from active transaction. + TM_CAUSE_SIGNAL Signal delivered. + TM_CAUSE_MISC Currently unused. + TM_CAUSE_ALIGNMENT Alignment fault. + TM_CAUSE_EMULATE Emulation that touched memory. + +These can be checked by the user program's abort handler as TEXASR[0:7]. If +bit 7 is set, it indicates that the error is consider persistent. For example +a TM_CAUSE_ALIGNMENT will be persistent while a TM_CAUSE_RESCHED will not. + +GDB +=== + +GDB and ptrace are not currently TM-aware. If one stops during a transaction, +it looks like the transaction has just started (the checkpointed state is +presented). The transaction cannot then be continued and will take the failure +handler route. Furthermore, the transactional 2nd register state will be +inaccessible. GDB can currently be used on programs using TM, but not sensibly +in parts within transactions. + +POWER9 +====== + +TM on POWER9 has issues with storing the complete register state. This +is described in this commit: + + commit 4bb3c7a0208fc13ca70598efd109901a7cd45ae7 + Author: Paul Mackerras + Date: Wed Mar 21 21:32:01 2018 +1100 + KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9 + +To account for this different POWER9 chips have TM enabled in +different ways. + +On POWER9N DD2.01 and below, TM is disabled. ie +HWCAP2[PPC_FEATURE2_HTM] is not set. + +On POWER9N DD2.1 TM is configured by firmware to always abort a +transaction when tm suspend occurs. So tsuspend will cause a +transaction to be aborted and rolled back. Kernel exceptions will also +cause the transaction to be aborted and rolled back and the exception +will not occur. If userspace constructs a sigcontext that enables TM +suspend, the sigcontext will be rejected by the kernel. This mode is +advertised to users with HWCAP2[PPC_FEATURE2_HTM_NO_SUSPEND] set. +HWCAP2[PPC_FEATURE2_HTM] is not set in this mode. + +On POWER9N DD2.2 and above, KVM and POWERVM emulate TM for guests (as +described in commit 4bb3c7a0208f), hence TM is enabled for guests +ie. HWCAP2[PPC_FEATURE2_HTM] is set for guest userspace. Guests that +makes heavy use of TM suspend (tsuspend or kernel suspend) will result +in traps into the hypervisor and hence will suffer a performance +degradation. Host userspace has TM disabled +ie. HWCAP2[PPC_FEATURE2_HTM] is not set. (although we make enable it +at some point in the future if we bring the emulation into host +userspace context switching). + +POWER9C DD1.2 and above are only available with POWERVM and hence +Linux only runs as a guest. On these systems TM is emulated like on +POWER9N DD2.2. + +Guest migration from POWER8 to POWER9 will work with POWER9N DD2.2 and +POWER9C DD1.2. Since earlier POWER9 processors don't support TM +emulation, migration from POWER8 to POWER9 is not supported there. -- cgit v1.2.3