From 76cb841cb886eef6b3bee341a2266c76578724ad Mon Sep 17 00:00:00 2001
From: Daniel Baumann <daniel.baumann@progress-linux.org>
Date: Mon, 6 May 2024 03:02:30 +0200
Subject: Adding upstream version 4.19.249.

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
---
 arch/arm/boot/dts/armada-xp-db-dxbc2.dts | 114 +++++++++++++++++++++++++++++++
 1 file changed, 114 insertions(+)
 create mode 100644 arch/arm/boot/dts/armada-xp-db-dxbc2.dts

(limited to 'arch/arm/boot/dts/armada-xp-db-dxbc2.dts')

diff --git a/arch/arm/boot/dts/armada-xp-db-dxbc2.dts b/arch/arm/boot/dts/armada-xp-db-dxbc2.dts
new file mode 100644
index 000000000..f42fc6118
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-db-dxbc2.dts
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for DB-DXBC2 board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx4251.dtsi"
+
+/ {
+	model = "Marvell Bobcat2 Evaluation Board";
+	compatible = "marvell,db-dxbc2", "marvell,armadaxp-98dx4251", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+	};
+
+};
+
+&devbus_bootcs {
+	status = "okay";
+
+	/* Device Bus parameters are required */
+
+	/* Read parameters */
+	devbus,bus-width    = <16>;
+	devbus,turn-off-ps  = <60000>;
+	devbus,badr-skew-ps = <0>;
+	devbus,acc-first-ps = <124000>;
+	devbus,acc-next-ps  = <248000>;
+	devbus,rd-setup-ps  = <0>;
+	devbus,rd-hold-ps   = <0>;
+
+	/* Write parameters */
+	devbus,sync-enable = <0>;
+	devbus,wr-high-ps  = <60000>;
+	devbus,wr-low-ps   = <60000>;
+	devbus,ale-wr-ps   = <60000>;
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&nand {
+	status = "okay";
+	label = "pxa3xx_nand-0";
+	num-cs = <1>;
+	marvell,nand-keep-config;
+	nand-on-flash-bbt;
+	nand-ecc-strength = <4>;
+	nand-ecc-step-size = <512>;
+};
+
+&sdio {
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	/* No CD or WP GPIOs */
+	broken-cd;
+};
+
+&spi0 {
+	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p64";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <20000000>;
+		m25p,fast-read;
+
+		partition@u-boot {
+			reg = <0x00000000 0x00100000>;
+			label = "u-boot";
+		};
+		partition@u-boot-env {
+			reg = <0x00100000 0x00040000>;
+			label = "u-boot-env";
+		};
+		partition@unused {
+			reg = <0x00140000 0x00ec0000>;
+			label = "unused";
+		};
+
+	};
+};
-- 
cgit v1.2.3