From 76cb841cb886eef6b3bee341a2266c76578724ad Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Mon, 6 May 2024 03:02:30 +0200 Subject: Adding upstream version 4.19.249. Signed-off-by: Daniel Baumann --- .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 311 +++++++++++++++++++++ 1 file changed, 311 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts (limited to 'arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts') diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts new file mode 100644 index 000000000..09a27e066 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts @@ -0,0 +1,311 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2016 Andreas Färber + * Copyright (c) 2016 BayLibre, Inc. + * Author: Kevin Hilman + */ + +/dts-v1/; + +#include "meson-gxbb.dtsi" +#include + +/ { + compatible = "hardkernel,odroid-c2", "amlogic,meson-gxbb"; + model = "Hardkernel ODROID-C2"; + + aliases { + serial0 = &uart_AO; + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + usb_otg_pwr: regulator-usb-pwrs { + compatible = "regulator-fixed"; + + regulator-name = "USB_OTG_PWR"; + + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + + gpio = <&gpio_ao GPIOAO_5 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + leds { + compatible = "gpio-leds"; + blue { + label = "c2:blue:alive"; + gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; + + tflash_vdd: regulator-tflash_vdd { + /* + * signal name from schematics: TFLASH_VDD_EN + */ + compatible = "regulator-fixed"; + + regulator-name = "TFLASH_VDD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio GPIOY_12 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + tf_io: gpio-regulator-tf_io { + compatible = "regulator-gpio"; + + regulator-name = "TF_IO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + /* + * signal name from schematics: TF_3V3N_1V8_EN + */ + gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + + states = <3300000 0 + 1800000 1>; + }; + + vcc1v8: regulator-vcc1v8 { + compatible = "regulator-fixed"; + regulator-name = "VCC1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vcc3v3: regulator-vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; +}; + +&cec_AO { + status = "okay"; + pinctrl-0 = <&ao_cec_pins>; + pinctrl-names = "default"; + hdmi-phandle = <&hdmi_tx>; +}; + +ðmac { + status = "okay"; + pinctrl-0 = <ð_rgmii_pins>; + pinctrl-names = "default"; + phy-handle = <ð_phy0>; + phy-mode = "rgmii"; + + snps,reset-gpio = <&gpio GPIOZ_14 0>; + snps,reset-delays-us = <0 10000 1000000>; + snps,reset-active-low; + + amlogic,tx-delay-ns = <2>; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + eth_phy0: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + interrupt-parent = <&gpio_intc>; + /* MAC_INTR on GPIOZ_15 */ + interrupts = <29 IRQ_TYPE_LEVEL_LOW>; + eee-broken-1000t; + }; + }; +}; + +&gpio_ao { + /* + * WARNING: The USB Hub on the Odroid-C2 needs a reset signal + * to be turned high in order to be detected by the USB Controller + * This signal should be handled by a USB specific power sequence + * in order to reset the Hub when USB bus is powered down. + */ + usb-hub { + gpio-hog; + gpios = ; + output-high; + line-name = "usb-hub-reset"; + }; +}; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>; + pinctrl-names = "default"; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; + +&i2c_A { + status = "okay"; + pinctrl-0 = <&i2c_a_pins>; + pinctrl-names = "default"; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + +&gpio_ao { + gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En", + "USB HUB nRESET", "USB OTG Power En", + "J7 Header Pin2", "IR In", "J7 Header Pin4", + "J7 Header Pin6", "J7 Header Pin5", "J7 Header Pin7", + "HDMI CEC", "SYS LED", + /* GPIO_TEST_N */ + ""; +}; + +&gpio { + gpio-line-names = /* Bank GPIOZ */ + "Eth MDIO", "Eth MDC", "Eth RGMII RX Clk", + "Eth RX DV", "Eth RX D0", "Eth RX D1", "Eth RX D2", + "Eth RX D3", "Eth RGMII TX Clk", "Eth TX En", + "Eth TX D0", "Eth TX D1", "Eth TX D2", "Eth TX D3", + "Eth PHY nRESET", "Eth PHY Intc", + /* Bank GPIOH */ + "HDMI HPD", "HDMI DDC SDA", "HDMI DDC SCL", "", + /* Bank BOOT */ + "eMMC D0", "eMMC D1", "eMMC D2", "eMMC D3", "eMMC D4", + "eMMC D5", "eMMC D6", "eMMC D7", "eMMC Clk", + "eMMC Reset", "eMMC CMD", + "", "", "", "", "", "", "", + /* Bank CARD */ + "SDCard D1", "SDCard D0", "SDCard CLK", "SDCard CMD", + "SDCard D3", "SDCard D2", "SDCard Det", + /* Bank GPIODV */ + "", "", "", "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", "", + "I2C A SDA", "I2C A SCK", "I2C B SDA", "I2C B SCK", + "PWM D", "PWM B", + /* Bank GPIOY */ + "Revision Bit0", "Revision Bit1", "", + "J2 Header Pin35", "", "", "", "J2 Header Pin36", + "J2 Header Pin31", "", "", "", "TF VDD En", + "J2 Header Pin32", "J2 Header Pin26", "", "", + /* Bank GPIOX */ + "J2 Header Pin29", "J2 Header Pin24", + "J2 Header Pin23", "J2 Header Pin22", + "J2 Header Pin21", "J2 Header Pin18", + "J2 Header Pin33", "J2 Header Pin19", + "J2 Header Pin16", "J2 Header Pin15", + "J2 Header Pin12", "J2 Header Pin13", + "J2 Header Pin8", "J2 Header Pin10", + "", "", "", "", "", + "J2 Header Pin11", "", "J2 Header Pin7", "", + /* Bank GPIOCLK */ + "", "", "", ""; +}; + +&saradc { + status = "okay"; + vref-supply = <&vcc1v8>; +}; + +&scpi_clocks { + status = "disabled"; +}; + +/* SD */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_pins>; + pinctrl-1 = <&sdcard_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <100000000>; + disable-wp; + + cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>; + cd-inverted; + + vmmc-supply = <&tflash_vdd>; + vqmmc-supply = <&tf_io>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + max-frequency = <100000000>; + non-removable; + disable-wp; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc3v3>; + vqmmc-supply = <&vcc1v8>; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb0_phy { + status = "disabled"; + phy-supply = <&usb_otg_pwr>; +}; + +&usb1_phy { + status = "okay"; + phy-supply = <&usb_otg_pwr>; +}; + +&usb0 { + status = "disabled"; +}; + +&usb1 { + status = "okay"; +}; -- cgit v1.2.3