From: Benedikt Spranger Date: Mon, 8 Mar 2010 18:57:04 +0100 Subject: [PATCH 030/342] clocksource: TCLIB: Allow higher clock rates for clock events MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Origin: https://git.kernel.org/cgit/linux/kernel/git/rt/linux-stable-rt.git/commit?id=08b49c99b7289f44964d91fe316ef6ae8c374390 As default the TCLIB uses the 32KiHz base clock rate for clock events. Add a compile time selection to allow higher clock resulution. (fixed up by Sami Pietikäinen ) Signed-off-by: Benedikt Spranger Signed-off-by: Thomas Gleixner --- drivers/clocksource/tcb_clksrc.c | 36 +++++++++++++++++++------------- drivers/misc/Kconfig | 12 +++++++++-- 2 files changed, 31 insertions(+), 17 deletions(-) diff --git a/drivers/clocksource/tcb_clksrc.c b/drivers/clocksource/tcb_clksrc.c index de6baf564dfe..ba15242a6066 100644 --- a/drivers/clocksource/tcb_clksrc.c +++ b/drivers/clocksource/tcb_clksrc.c @@ -25,8 +25,7 @@ * this 32 bit free-running counter. the second channel is not used. * * - The third channel may be used to provide a 16-bit clockevent - * source, used in either periodic or oneshot mode. This runs - * at 32 KiHZ, and can handle delays of up to two seconds. + * source, used in either periodic or oneshot mode. * * A boot clocksource and clockevent source are also currently needed, * unless the relevant platforms (ARM/AT91, AVR32/AT32) are changed so @@ -127,6 +126,7 @@ struct tc_clkevt_device { struct clock_event_device clkevt; struct clk *clk; bool clk_enabled; + u32 freq; void __iomem *regs; }; @@ -135,13 +135,6 @@ static struct tc_clkevt_device *to_tc_clkevt(struct clock_event_device *clkevt) return container_of(clkevt, struct tc_clkevt_device, clkevt); } -/* For now, we always use the 32K clock ... this optimizes for NO_HZ, - * because using one of the divided clocks would usually mean the - * tick rate can never be less than several dozen Hz (vs 0.5 Hz). - * - * A divided clock could be good for high resolution timers, since - * 30.5 usec resolution can seem "low". - */ static u32 timer_clock; static void tc_clk_disable(struct clock_event_device *d) @@ -191,7 +184,7 @@ static int tc_set_oneshot(struct clock_event_device *d) tc_clk_enable(d); - /* slow clock, count up to RC, then irq and stop */ + /* count up to RC, then irq and stop */ writel(timer_clock | ATMEL_TC_CPCSTOP | ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO, regs + ATMEL_TC_REG(2, CMR)); writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER)); @@ -213,10 +206,10 @@ static int tc_set_periodic(struct clock_event_device *d) */ tc_clk_enable(d); - /* slow clock, count up to RC, then irq and restart */ + /* count up to RC, then irq and restart */ writel(timer_clock | ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO, regs + ATMEL_TC_REG(2, CMR)); - writel((32768 + HZ / 2) / HZ, tcaddr + ATMEL_TC_REG(2, RC)); + writel((tcd->freq + HZ / 2) / HZ, tcaddr + ATMEL_TC_REG(2, RC)); /* Enable clock and interrupts on RC compare */ writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER)); @@ -243,7 +236,11 @@ static struct tc_clkevt_device clkevt = { .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT, /* Should be lower than at91rm9200's system timer */ +#ifdef CONFIG_ATMEL_TCB_CLKSRC_USE_SLOW_CLOCK .rating = 125, +#else + .rating = 200, +#endif .set_next_event = tc_next_event, .set_state_shutdown = tc_shutdown_clk_off, .set_state_periodic = tc_set_periodic, @@ -265,8 +262,9 @@ static irqreturn_t ch2_irq(int irq, void *handle) return IRQ_NONE; } -static int __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx) +static int __init setup_clkevents(struct atmel_tc *tc, int divisor_idx) { + unsigned divisor = atmel_tc_divisors[divisor_idx]; int ret; struct clk *t2_clk = tc->clk[2]; int irq = tc->irq[2]; @@ -287,7 +285,11 @@ static int __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx) clkevt.regs = tc->regs; clkevt.clk = t2_clk; - timer_clock = clk32k_divisor_idx; + timer_clock = divisor_idx; + if (!divisor) + clkevt.freq = 32768; + else + clkevt.freq = clk_get_rate(t2_clk) / divisor; clkevt.clkevt.cpumask = cpumask_of(0); @@ -298,7 +300,7 @@ static int __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx) return ret; } - clockevents_config_and_register(&clkevt.clkevt, 32768, 1, 0xffff); + clockevents_config_and_register(&clkevt.clkevt, clkevt.freq, 1, 0xffff); return ret; } @@ -435,7 +437,11 @@ static int __init tcb_clksrc_init(void) goto err_disable_t1; /* channel 2: periodic and oneshot timer support */ +#ifdef CONFIG_ATMEL_TCB_CLKSRC_USE_SLOW_CLOCK ret = setup_clkevents(tc, clk32k_divisor_idx); +#else + ret = setup_clkevents(tc, best_divisor_idx); +#endif if (ret) goto err_unregister_clksrc; diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig index 3726eacdf65d..0900dec7ec04 100644 --- a/drivers/misc/Kconfig +++ b/drivers/misc/Kconfig @@ -69,8 +69,7 @@ config ATMEL_TCB_CLKSRC are combined to make a single 32-bit timer. When GENERIC_CLOCKEVENTS is defined, the third timer channel - may be used as a clock event device supporting oneshot mode - (delays of up to two seconds) based on the 32 KiHz clock. + may be used as a clock event device supporting oneshot mode. config ATMEL_TCB_CLKSRC_BLOCK int @@ -83,6 +82,15 @@ config ATMEL_TCB_CLKSRC_BLOCK TC can be used for other purposes, such as PWM generation and interval timing. +config ATMEL_TCB_CLKSRC_USE_SLOW_CLOCK + bool "TC Block use 32 KiHz clock" + depends on ATMEL_TCB_CLKSRC + default y + help + Select this to use 32 KiHz base clock rate as TC block clock + source for clock events. + + config DUMMY_IRQ tristate "Dummy IRQ handler" default n