blob: d18772d6bc6560f460f06c5072735874b9890861 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
|
* STMicroelectronics STM32 MDMA controller
The STM32 MDMA is a general-purpose direct memory access controller capable of
supporting 64 independent DMA channels with 256 HW requests.
Required properties:
- compatible: Should be "st,stm32h7-mdma"
- reg: Should contain MDMA registers location and length. This should include
all of the per-channel registers.
- interrupts: Should contain the MDMA interrupt.
- clocks: Should contain the input clock of the DMA instance.
- resets: Reference to a reset controller asserting the DMA controller.
- #dma-cells : Must be <5>. See DMA client paragraph for more details.
Optional properties:
- dma-channels: Number of DMA channels supported by the controller.
- dma-requests: Number of DMA request signals supported by the controller.
- st,ahb-addr-masks: Array of u32 mask to list memory devices addressed via
AHB bus.
Example:
mdma1: dma@52000000 {
compatible = "st,stm32h7-mdma";
reg = <0x52000000 0x1000>;
interrupts = <122>;
clocks = <&timer_clk>;
resets = <&rcc 992>;
#dma-cells = <5>;
dma-channels = <16>;
dma-requests = <32>;
st,ahb-addr-masks = <0x20000000>, <0x00000000>;
};
* DMA client
DMA clients connected to the STM32 MDMA controller must use the format
described in the dma.txt file, using a five-cell specifier for each channel:
a phandle to the MDMA controller plus the following five integer cells:
1. The request line number
2. The priority level
0x00: Low
0x01: Medium
0x10: High
0x11: Very high
3. A 32bit mask specifying the DMA channel configuration
-bit 0-1: Source increment mode
0x00: Source address pointer is fixed
0x10: Source address pointer is incremented after each data transfer
0x11: Source address pointer is decremented after each data transfer
-bit 2-3: Destination increment mode
0x00: Destination address pointer is fixed
0x10: Destination address pointer is incremented after each data
transfer
0x11: Destination address pointer is decremented after each data
transfer
-bit 8-9: Source increment offset size
0x00: byte (8bit)
0x01: half-word (16bit)
0x10: word (32bit)
0x11: double-word (64bit)
-bit 10-11: Destination increment offset size
0x00: byte (8bit)
0x01: half-word (16bit)
0x10: word (32bit)
0x11: double-word (64bit)
-bit 25-18: The number of bytes to be transferred in a single transfer
(min = 1 byte, max = 128 bytes)
-bit 29:28: Trigger Mode
0x00: Each MDMA request triggers a buffer transfer (max 128 bytes)
0x01: Each MDMA request triggers a block transfer (max 64K bytes)
0x10: Each MDMA request triggers a repeated block transfer
0x11: Each MDMA request triggers a linked list transfer
4. A 32bit value specifying the register to be used to acknowledge the request
if no HW ack signal is used by the MDMA client
5. A 32bit mask specifying the value to be written to acknowledge the request
if no HW ack signal is used by the MDMA client
Example:
i2c4: i2c@5c002000 {
compatible = "st,stm32f7-i2c";
reg = <0x5c002000 0x400>;
interrupts = <95>,
<96>;
clocks = <&timer_clk>;
#address-cells = <1>;
#size-cells = <0>;
dmas = <&mdma1 36 0x0 0x40008 0x0 0x0>,
<&mdma1 37 0x0 0x40002 0x0 0x0>;
dma-names = "rx", "tx";
status = "disabled";
};
|
