Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

76 files changed, 3328 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt
new file mode 100644
index 000000000..e9de37567
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/brcm,bcm2835-i2c.txt
@@ -0,0 +1,20 @@
+Broadcom BCM2835 I2C controller
+
+Required properties:
+- compatible : Should be "brcm,bcm2835-i2c".
+- reg: Should contain register location and length.
+- interrupts: Should contain interrupt.
+- clocks : The clock feeding the I2C controller.
+
+Recommended properties:
+- clock-frequency : desired I2C bus clock frequency in Hz.
+
+Example:
+
+i2c@20205000 {
+	compatible = "brcm,bcm2835-i2c";
+	reg = <0x7e205000 0x1000>;
+	interrupts = <2 21>;
+	clocks = <&clk_i2c>;
+	clock-frequency = <100000>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
new file mode 100644
index 000000000..81f982ccc
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt
@@ -0,0 +1,37 @@
+Broadcom iProc I2C controller
+
+Required properties:
+
+- compatible:
+    Must be "brcm,iproc-i2c"
+
+- reg:
+    Define the base and range of the I/O address space that contain the iProc
+    I2C controller registers
+
+- interrupts:
+    Should contain the I2C interrupt
+
+- clock-frequency:
+    This is the I2C bus clock. Need to be either 100000 or 400000
+
+- #address-cells:
+    Always 1 (for I2C addresses)
+
+- #size-cells:
+    Always 0
+
+Example:
+	i2c0: i2c@18008000 {
+		compatible = "brcm,iproc-i2c";
+		reg = <0x18008000 0x100>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+		clock-frequency = <100000>;
+
+		codec: wm8750@1a {
+			compatible = "wlf,wm8750";
+			reg = <0x1a>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/brcm,kona-i2c.txt b/Documentation/devicetree/bindings/i2c/brcm,kona-i2c.txt
new file mode 100644
index 000000000..1b87b741f
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/brcm,kona-i2c.txt
@@ -0,0 +1,35 @@
+Broadcom Kona Family I2C
+=========================
+
+This I2C controller is used in the following Broadcom SoCs:
+
+  BCM11130
+  BCM11140
+  BCM11351
+  BCM28145
+  BCM28155
+
+Required Properties
+-------------------
+- compatible: "brcm,bcm11351-i2c", "brcm,kona-i2c"
+- reg: Physical base address and length of controller registers
+- interrupts: The interrupt number used by the controller
+- clocks: clock specifier for the kona i2c external clock
+- clock-frequency: The I2C bus frequency in Hz
+- #address-cells: Should be <1>
+- #size-cells: Should be <0>
+
+Refer to clocks/clock-bindings.txt for generic clock consumer
+properties.
+
+Example:
+
+i2c@3e016000 {
+	compatible = "brcm,bcm11351-i2c","brcm,kona-i2c";
+	reg = <0x3e016000 0x80>;
+	interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&bsc1_clk>;
+	clock-frequency = <400000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-altera.txt b/Documentation/devicetree/bindings/i2c/i2c-altera.txt
new file mode 100644
index 000000000..767664f44
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-altera.txt
@@ -0,0 +1,39 @@
+* Altera I2C Controller
+* This is Altera's synthesizable logic block I2C Controller for use
+* in Altera's FPGAs.
+
+Required properties :
+ - compatible : should be "altr,softip-i2c-v1.0"
+ - reg        : Offset and length of the register set for the device
+ - interrupts : <IRQ> where IRQ is the interrupt number.
+ - clocks     : phandle to input clock.
+ - #address-cells = <1>;
+ - #size-cells = <0>;
+
+Recommended properties :
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+
+Optional properties :
+ - fifo-size : Size of the RX and TX FIFOs in bytes.
+ - Child nodes conforming to i2c bus binding
+
+Example :
+
+	i2c@100080000 {
+		compatible = "altr,softip-i2c-v1.0";
+		reg = <0x00000001 0x00080000 0x00000040>;
+		interrupt-parent = <&intc>;
+		interrupts = <0 43 4>;
+		clocks = <&clk_0>;
+		clock-frequency = <100000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		fifo-size = <4>;
+
+		eeprom@51 {
+			compatible = "atmel,24c32";
+			reg = <0x51>;
+			pagesize = <32>;
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt
new file mode 100644
index 000000000..548a73cde
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-arb-gpio-challenge.txt
@@ -0,0 +1,82 @@
+GPIO-based I2C Arbitration Using a Challenge & Response Mechanism
+=================================================================
+This uses GPIO lines and a challenge & response mechanism to arbitrate who is
+the master of an I2C bus in a multimaster situation.
+
+In many cases using GPIOs to arbitrate is not needed and a design can use
+the standard I2C multi-master rules.  Using GPIOs is generally useful in
+the case where there is a device on the bus that has errata and/or bugs
+that makes standard multimaster mode not feasible.
+
+Note that this scheme works well enough but has some downsides:
+* It is nonstandard (not using standard I2C multimaster)
+* Having two masters on a bus in general makes it relatively hard to debug
+  problems (hard to tell if i2c issues were caused by one master, another, or
+  some device on the bus).
+
+
+Algorithm:
+
+All masters on the bus have a 'bus claim' line which is an output that the
+others can see. These are all active low with pull-ups enabled.  We'll
+describe these lines as:
+
+- OUR_CLAIM: output from us signaling to other hosts that we want the bus
+- THEIR_CLAIMS: output from others signaling that they want the bus
+
+The basic algorithm is to assert your line when you want the bus, then make
+sure that the other side doesn't want it also.  A detailed explanation is best
+done with an example.
+
+Let's say we want to claim the bus.  We:
+1. Assert OUR_CLAIM.
+2. Waits a little bit for the other sides to notice (slew time, say 10
+   microseconds).
+3. Check THEIR_CLAIMS.  If none are asserted then the we have the bus and we are
+   done.
+4. Otherwise, wait for a few milliseconds and see if THEIR_CLAIMS are released.
+5. If not, back off, release the claim and wait for a few more milliseconds.
+6. Go back to 1 (until retry time has expired).
+
+
+Required properties:
+- compatible: i2c-arb-gpio-challenge
+- our-claim-gpio: The GPIO that we use to claim the bus.
+- their-claim-gpios: The GPIOs that the other sides use to claim the bus.
+  Note that some implementations may only support a single other master.
+- I2C arbitration bus node. See i2c-arb.txt in this directory.
+
+Optional properties:
+- slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us.
+- wait-retry-us: we'll attempt another claim after this many microseconds.
+    Default is 3000 us.
+- wait-free-us: we'll give up after this many microseconds. Default is 50000 us.
+
+
+Example:
+	i2c@12ca0000 {
+		compatible = "acme,some-i2c-device";
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2c-arbitrator {
+		compatible = "i2c-arb-gpio-challenge";
+
+		i2c-parent = <&{/i2c@12CA0000}>;
+
+		our-claim-gpio = <&gpf0 3 1>;
+		their-claim-gpios = <&gpe0 4 1>;
+		slew-delay-us = <10>;
+		wait-retry-us = <3000>;
+		wait-free-us = <50000>;
+
+		i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c@52 {
+				// Normal I2C device
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-arb.txt b/Documentation/devicetree/bindings/i2c/i2c-arb.txt
new file mode 100644
index 000000000..59abf9277
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-arb.txt
@@ -0,0 +1,35 @@
+Common i2c arbitration bus properties.
+
+- i2c-arb child node
+
+Required properties for the i2c-arb child node:
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties for i2c-arb child node:
+- Child nodes conforming to i2c bus binding
+
+
+Example :
+
+	/*
+	   An NXP pca9541 I2C bus master selector at address 0x74
+	   with a NXP pca8574 GPIO expander attached.
+	 */
+
+	arb@74 {
+		compatible = "nxp,pca9541";
+		reg = <0x74>;
+
+		i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio@38 {
+				compatible = "nxp,pca8574";
+				reg = <0x38>;
+				#gpio-cells = <2>;
+				gpio-controller;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
new file mode 100644
index 000000000..8fbd8633a
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-aspeed.txt
@@ -0,0 +1,48 @@
+Device tree configuration for the I2C busses on the AST24XX and AST25XX SoCs.
+
+Required Properties:
+- #address-cells	: should be 1
+- #size-cells		: should be 0
+- reg			: address offset and range of bus
+- compatible		: should be "aspeed,ast2400-i2c-bus"
+			  or "aspeed,ast2500-i2c-bus"
+- clocks		: root clock of bus, should reference the APB
+			  clock in the second cell
+- resets		: phandle to reset controller with the reset number in
+			  the second cell
+- interrupts		: interrupt number
+
+Optional Properties:
+- bus-frequency	: frequency of the bus clock in Hz defaults to 100 kHz when not
+		  specified
+- multi-master	: states that there is another master active on this bus.
+
+Example:
+
+i2c {
+	compatible = "simple-bus";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges = <0 0x1e78a000 0x1000>;
+
+	i2c_ic: interrupt-controller@0 {
+		#interrupt-cells = <1>;
+		compatible = "aspeed,ast2400-i2c-ic";
+		reg = <0x0 0x40>;
+		interrupts = <12>;
+		interrupt-controller;
+	};
+
+	i2c0: i2c-bus@40 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#interrupt-cells = <1>;
+		reg = <0x40 0x40>;
+		compatible = "aspeed,ast2400-i2c-bus";
+		clocks = <&syscon ASPEED_CLK_APB>;
+		resets = <&syscon ASPEED_RESET_I2C>;
+		bus-frequency = <100000>;
+		interrupts = <0>;
+		interrupt-parent = <&i2c_ic>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-at91.txt b/Documentation/devicetree/bindings/i2c/i2c-at91.txt
new file mode 100644
index 000000000..ef973a034
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-at91.txt
@@ -0,0 +1,63 @@
+I2C for Atmel platforms
+
+Required properties :
+- compatible : Must be "atmel,at91rm9200-i2c", "atmel,at91sam9261-i2c",
+     "atmel,at91sam9260-i2c", "atmel,at91sam9g20-i2c", "atmel,at91sam9g10-i2c",
+     "atmel,at91sam9x5-i2c", "atmel,sama5d4-i2c" or "atmel,sama5d2-i2c"
+- reg: physical base address of the controller and length of memory mapped
+     region.
+- interrupts: interrupt number to the cpu.
+- #address-cells = <1>;
+- #size-cells = <0>;
+- clocks: phandles to input clocks.
+
+Optional properties:
+- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000
+- dmas: A list of two dma specifiers, one for each entry in dma-names.
+- dma-names: should contain "tx" and "rx".
+- atmel,fifo-size: maximum number of data the RX and TX FIFOs can store for FIFO
+  capable I2C controllers.
+- i2c-sda-hold-time-ns: TWD hold time, only available for "atmel,sama5d4-i2c"
+  and "atmel,sama5d2-i2c".
+- Child nodes conforming to i2c bus binding
+
+Examples :
+
+i2c0: i2c@fff84000 {
+	compatible = "atmel,at91sam9g20-i2c";
+	reg = <0xfff84000 0x100>;
+	interrupts = <12 4 6>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clocks = <&twi0_clk>;
+	clock-frequency = <400000>;
+
+	24c512@50 {
+		compatible = "24c512";
+		reg = <0x50>;
+		pagesize = <128>;
+	}
+}
+
+i2c0: i2c@f8034600 {
+	compatible = "atmel,sama5d2-i2c";
+	reg = <0xf8034600 0x100>;
+	interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
+	dmas = <&dma0
+		(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
+		AT91_XDMAC_DT_PERID(11)>,
+	       <&dma0
+		(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1))
+		AT91_XDMAC_DT_PERID(12)>;
+	dma-names = "tx", "rx";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clocks = <&flx0>;
+	atmel,fifo-size = <16>;
+	i2c-sda-hold-time-ns = <336>;
+
+	wm8731: wm8731@1a {
+		compatible = "wm8731";
+		reg = <0x1a>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-axxia.txt b/Documentation/devicetree/bindings/i2c/i2c-axxia.txt
new file mode 100644
index 000000000..7d53a2b79
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-axxia.txt
@@ -0,0 +1,30 @@
+LSI Axxia I2C
+
+Required properties :
+- compatible : Must be "lsi,api2c"
+- reg : Offset and length of the register set for the device
+- interrupts : the interrupt specifier
+- #address-cells : Must be <1>;
+- #size-cells : Must be <0>;
+- clock-names : Must contain "i2c".
+- clocks: Must contain an entry for each name in clock-names. See the common
+  clock bindings.
+
+Optional properties :
+- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
+  the default 100 kHz frequency will be used. As only Normal and Fast modes
+  are supported, possible values are 100000 and 400000.
+
+Example :
+
+i2c@2010084000 {
+	compatible = "lsi,api2c";
+	device_type = "i2c";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x20 0x10084000 0x00 0x1000>;
+	interrupts = <0 19 4>;
+	clocks = <&clk_per>;
+	clock-names = "i2c";
+	clock-frequency = <400000>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-brcmstb.txt b/Documentation/devicetree/bindings/i2c/i2c-brcmstb.txt
new file mode 100644
index 000000000..0380609b1
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-brcmstb.txt
@@ -0,0 +1,26 @@
+Broadcom stb bsc iic master controller
+
+Required properties:
+
+- compatible: should be "brcm,brcmstb-i2c" or "brcm,brcmper-i2c"
+- clock-frequency: 32-bit decimal value of iic master clock freqency in Hz
+		   valid values are 375000, 390000, 187500, 200000
+		   93750, 97500, 46875 and 50000
+- reg: specifies the base physical address and size of the registers
+
+Optional properties :
+
+- interrupts: specifies the interrupt number, the irq line to be used
+- interrupt-names: Interrupt name string
+
+Example:
+
+bsca: i2c@f0406200 {
+      clock-frequency = <390000>;
+      compatible = "brcm,brcmstb-i2c";
+      interrupt-parent = <&irq0_intc>;
+      reg = <0xf0406200 0x58>;
+      interrupts = <0x18>;
+      interrupt-names = "upg_bsca";
+};
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-cadence.txt b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt
new file mode 100644
index 000000000..ebaa90c58
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-cadence.txt
@@ -0,0 +1,28 @@
+Binding for the Cadence I2C controller
+
+Required properties:
+  - reg: Physical base address and size of the controller's register area.
+  - compatible: Should contain one of:
+		* "cdns,i2c-r1p10"
+		Note:	Use this when cadence i2c controller version 1.0 is used.
+		* "cdns,i2c-r1p14"
+		Note:	Use this when cadence i2c controller version 1.4 is used.
+  - clocks: Input clock specifier. Refer to common clock bindings.
+  - interrupts: Interrupt specifier. Refer to interrupt bindings.
+  - #address-cells: Should be 1.
+  - #size-cells: Should be 0.
+
+Optional properties:
+  - clock-frequency: Desired operating frequency, in Hz, of the bus.
+  - clock-names: Input clock name, should be 'pclk'.
+
+Example:
+	i2c@e0004000 {
+		compatible = "cdns,i2c-r1p10";
+		clocks = <&clkc 38>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0xe0004000 0x1000>;
+		clock-frequency = <400000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt
new file mode 100644
index 000000000..c143948b2
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-cbus-gpio.txt
@@ -0,0 +1,27 @@
+Device tree bindings for i2c-cbus-gpio driver
+
+Required properties:
+	- compatible = "i2c-cbus-gpio";
+	- gpios: clk, dat, sel
+	- #address-cells = <1>;
+	- #size-cells = <0>;
+
+Optional properties:
+	- child nodes conforming to i2c bus binding
+
+Example:
+
+i2c@0 {
+	compatible = "i2c-cbus-gpio";
+	gpios = <&gpio 66 0 /* clk */
+		 &gpio 65 0 /* dat */
+		 &gpio 64 0 /* sel */
+		>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	retu: retu@1 {
+		compatible = "nokia,retu";
+		reg = <0x1>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt b/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt
new file mode 100644
index 000000000..898f030eb
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-cros-ec-tunnel.txt
@@ -0,0 +1,39 @@
+I2C bus that tunnels through the ChromeOS EC (cros-ec)
+======================================================
+On some ChromeOS board designs we've got a connection to the EC (embedded
+controller) but no direct connection to some devices on the other side of
+the EC (like a battery and PMIC).  To get access to those devices we need
+to tunnel our i2c commands through the EC.
+
+The node for this device should be under a cros-ec node like google,cros-ec-spi
+or google,cros-ec-i2c.
+
+
+Required properties:
+- compatible: google,cros-ec-i2c-tunnel
+- google,remote-bus: The EC bus we'd like to talk to.
+
+Optional child nodes:
+- One node per I2C device connected to the tunnelled I2C bus.
+
+
+Example:
+	cros-ec@0 {
+		compatible = "google,cros-ec-spi";
+
+		...
+
+		i2c-tunnel {
+			compatible = "google,cros-ec-i2c-tunnel";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			google,remote-bus = <0>;
+
+			battery: sbs-battery@b {
+				compatible = "sbs,sbs-battery";
+				reg = <0xb>;
+				sbs,poll-retry-count = <1>;
+			};
+		};
+	}
diff --git a/Documentation/devicetree/bindings/i2c/i2c-davinci.txt b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt
new file mode 100644
index 000000000..b745f3706
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-davinci.txt
@@ -0,0 +1,43 @@
+* Texas Instruments Davinci/Keystone I2C
+
+This file provides information, what the device node for the
+davinci/keystone i2c interface contains.
+
+Required properties:
+- compatible: "ti,davinci-i2c" or "ti,keystone-i2c";
+- reg : Offset and length of the register set for the device
+- clocks: I2C functional clock phandle.
+	  For 66AK2G this property should be set per binding,
+	  Documentation/devicetree/bindings/clock/ti,sci-clk.txt
+
+SoC-specific Required Properties:
+
+The following are mandatory properties for Keystone 2 66AK2G SoCs only:
+
+- power-domains:	Should contain a phandle to a PM domain provider node
+			and an args specifier containing the I2C device id
+			value. This property is as per the binding,
+			Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
+
+Recommended properties :
+- interrupts : standard interrupt property.
+- clock-frequency : desired I2C bus clock frequency in Hz.
+- ti,has-pfunc: boolean; if defined, it indicates that SoC supports PFUNC
+	registers. PFUNC registers allow to switch I2C pins to function as
+	GPIOs, so they can be toggled manually.
+
+Example (enbw_cmc board):
+	i2c@1c22000 {
+		compatible = "ti,davinci-i2c";
+		reg = <0x22000 0x1000>;
+		clock-frequency = <100000>;
+		interrupts = <15>;
+		interrupt-parent = <&intc>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		dtt@48 {
+			compatible = "national,lm75";
+			reg = <0x48>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt
new file mode 100644
index 000000000..81b5d5508
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-demux-pinctrl.txt
@@ -0,0 +1,135 @@
+Pinctrl-based I2C Bus DeMux
+
+This binding describes an I2C bus demultiplexer that uses pin multiplexing to
+route the I2C signals, and represents the pin multiplexing configuration using
+the pinctrl device tree bindings. This may be used to select one I2C IP core at
+runtime which may have a better feature set for a given task than another I2C
+IP core on the SoC. The most simple example is to fall back to GPIO bitbanging
+if your current runtime configuration hits an errata of the internal IP core.
+
+    +-------------------------------+
+    | SoC                           |
+    |                               |   +-----+  +-----+
+    |   +------------+              |   | dev |  | dev |
+    |   |I2C IP Core1|--\           |   +-----+  +-----+
+    |   +------------+   \-------+  |      |        |
+    |                    |Pinctrl|--|------+--------+
+    |   +------------+   +-------+  |
+    |   |I2C IP Core2|--/           |
+    |   +------------+              |
+    |                               |
+    +-------------------------------+
+
+Required properties:
+- compatible: "i2c-demux-pinctrl"
+- i2c-parent: List of phandles of I2C masters available for selection. The first
+	      one will be used as default.
+- i2c-bus-name: The name of this bus. Also needed as pinctrl-name for the I2C
+		parents.
+
+Furthermore, I2C mux properties and child nodes. See i2c-mux.txt in this
+directory.
+
+Example:
+
+Here is a snipplet for a bus to be demuxed. It contains various i2c clients for
+HDMI, so the bus is named "i2c-hdmi":
+
+	i2chdmi: i2c@8 {
+
+		compatible = "i2c-demux-pinctrl";
+		i2c-parent = <&gpioi2c>, <&iic2>, <&i2c2>;
+		i2c-bus-name = "i2c-hdmi";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ak4643: sound-codec@12 {
+			compatible = "asahi-kasei,ak4643";
+
+			#sound-dai-cells = <0>;
+			reg = <0x12>;
+		};
+
+		composite-in@20 {
+			compatible = "adi,adv7180";
+			reg = <0x20>;
+			remote = <&vin1>;
+
+			port {
+				adv7180: endpoint {
+					bus-width = <8>;
+					remote-endpoint = <&vin1ep0>;
+				};
+			};
+		};
+
+		hdmi@39 {
+			compatible = "adi,adv7511w";
+			reg = <0x39>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+
+			adi,input-depth = <8>;
+			adi,input-colorspace = "rgb";
+			adi,input-clock = "1x";
+			adi,input-style = <1>;
+			adi,input-justification = "evenly";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					adv7511_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					adv7511_out: endpoint {
+						remote-endpoint = <&hdmi_con>;
+					};
+				};
+			};
+		};
+	};
+
+And for clarification, here are the snipplets for the i2c-parents:
+
+	gpioi2c: i2c@9 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "i2c-gpio";
+		gpios = <&gpio5 6 GPIO_ACTIVE_HIGH /* sda */
+			 &gpio5 5 GPIO_ACTIVE_HIGH /* scl */
+			>;
+		i2c-gpio,delay-us = <5>;
+	};
+
+...
+
+&i2c2	{
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "i2c-hdmi";
+
+	clock-frequency = <100000>;
+};
+
+...
+
+&iic2	{
+	pinctrl-0 = <&iic2_pins>;
+	pinctrl-names = "i2c-hdmi";
+
+	clock-frequency = <100000>;
+};
+
+Please note:
+
+- pinctrl properties for the parent I2C controllers need a pinctrl state
+  with the same name as i2c-bus-name, not "default"!
+
+- the i2c masters must have their status "disabled". This driver will
+  enable them at runtime when needed.
diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
new file mode 100644
index 000000000..fbb0a6d8b
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
@@ -0,0 +1,59 @@
+* Synopsys DesignWare I2C
+
+Required properties :
+
+ - compatible : should be "snps,designware-i2c"
+ - reg : Offset and length of the register set for the device
+ - interrupts : <IRQ> where IRQ is the interrupt number.
+
+Recommended properties :
+
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+
+Optional properties :
+ - i2c-sda-hold-time-ns : should contain the SDA hold time in nanoseconds.
+   This option is only supported in hardware blocks version 1.11a or newer.
+
+ - i2c-scl-falling-time-ns : should contain the SCL falling time in nanoseconds.
+   This value which is by default 300ns is used to compute the tLOW period.
+
+ - i2c-sda-falling-time-ns : should contain the SDA falling time in nanoseconds.
+   This value which is by default 300ns is used to compute the tHIGH period.
+
+Examples :
+
+	i2c@f0000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,designware-i2c";
+		reg = <0xf0000 0x1000>;
+		interrupts = <11>;
+		clock-frequency = <400000>;
+	};
+
+	i2c@1120000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,designware-i2c";
+		reg = <0x1120000 0x1000>;
+		interrupt-parent = <&ictl>;
+		interrupts = <12 1>;
+		clock-frequency = <400000>;
+		i2c-sda-hold-time-ns = <300>;
+		i2c-sda-falling-time-ns = <300>;
+		i2c-scl-falling-time-ns = <300>;
+	};
+
+	i2c@1120000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x2000 0x100>;
+		clock-frequency = <400000>;
+		clocks = <&i2cclk>;
+		interrupts = <0>;
+
+		eeprom@64 {
+			compatible = "linux,slave-24c02";
+			reg = <0x40000064>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-digicolor.txt b/Documentation/devicetree/bindings/i2c/i2c-digicolor.txt
new file mode 100644
index 000000000..457a098d4
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-digicolor.txt
@@ -0,0 +1,25 @@
+Conexant Digicolor I2C controller
+
+Required properties:
+ - compatible: must be "cnxt,cx92755-i2c"
+ - reg: physical address and length of the device registers
+ - interrupts: a single interrupt specifier
+ - clocks: clock for the device
+ - #address-cells: should be <1>
+ - #size-cells: should be <0>
+
+Optional properties:
+- clock-frequency: the desired I2C bus clock frequency in Hz; in
+  absence of this property the default value is used (100 kHz).
+
+Example:
+
+	i2c: i2c@f0000120 {
+		compatible = "cnxt,cx92755-i2c";
+		reg = <0xf0000120 0x10>;
+		interrupts = <28>;
+		clocks = <&main_clk>;
+		clock-frequency = <100000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-efm32.txt b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt
new file mode 100644
index 000000000..3b30e54ae
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-efm32.txt
@@ -0,0 +1,33 @@
+* Energymicro efm32 i2c controller
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "energymicro,efm32-i2c"
+ - interrupts : the interrupt number
+ - clocks : reference to the module clock
+
+Recommended properties :
+
+ - clock-frequency : maximal I2C bus clock frequency in Hz.
+ - energymicro,location : Decides the location of the USART I/O pins.
+   Allowed range : [0 .. 6]
+
+Example:
+	i2c0: i2c@4000a000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "energymicro,efm32-i2c";
+		reg = <0x4000a000 0x400>;
+		interrupts = <9>;
+		clocks = <&cmu clk_HFPERCLKI2C0>;
+		clock-frequency = <100000>;
+		energymicro,location = <3>;
+
+		eeprom@50 {
+			compatible = "microchip,24c02";
+			reg = <0x50>;
+			pagesize = <16>;
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-emev2.txt b/Documentation/devicetree/bindings/i2c/i2c-emev2.txt
new file mode 100644
index 000000000..5ed1ea1c7
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-emev2.txt
@@ -0,0 +1,22 @@
+Device tree configuration for Renesas EMEV2 IIC controller
+
+Required properties:
+- compatible      : "renesas,iic-emev2"
+- reg             : address start and address range size of device
+- interrupts      : specifier for the IIC controller interrupt
+- clocks          : phandle to the IP core SCLK
+- clock-names     : must be "sclk"
+- #address-cells  : should be <1>
+- #size-cells     : should be <0>
+
+Example:
+
+	iic0: i2c@e0070000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "renesas,iic-emev2";
+		reg = <0xe0070000 0x28>;
+		interrupts = <0 32 IRQ_TYPE_EDGE_RISING>;
+		clocks = <&iic0_sclk>;
+		clock-names = "sclk";
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
new file mode 100644
index 000000000..2dbc0b62d
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-exynos5.txt
@@ -0,0 +1,53 @@
+* Samsung's High Speed I2C controller
+
+The Samsung's High Speed I2C controller is used to interface with I2C devices
+at various speeds ranging from 100khz to 3.4Mhz.
+
+Required properties:
+  - compatible: value should be.
+	-> "samsung,exynos5-hsi2c", (DEPRECATED)
+				for i2c compatible with HSI2C available
+				on Exynos5250 and Exynos5420 SoCs.
+	-> "samsung,exynos5250-hsi2c", for i2c compatible with HSI2C available
+				on Exynos5250 and Exynos5420 SoCs.
+	-> "samsung,exynos5260-hsi2c", for i2c compatible with HSI2C available
+				on Exynos5260 SoCs.
+	-> "samsung,exynos7-hsi2c", for i2c compatible with HSI2C available
+				on Exynos7 SoCs.
+
+  - reg: physical base address of the controller and length of memory mapped
+    region.
+  - interrupts: interrupt number to the cpu.
+  - #address-cells: always 1 (for i2c addresses)
+  - #size-cells: always 0
+
+  - Pinctrl:
+    - pinctrl-0: Pin control group to be used for this controller.
+    - pinctrl-names: Should contain only one value - "default".
+
+Optional properties:
+  - clock-frequency: Desired operating frequency in Hz of the bus.
+    -> If not specified, the bus operates in fast-speed mode at
+       at 100khz.
+    -> If specified, the bus operates in high-speed mode only if the
+       clock-frequency is >= 1Mhz.
+
+Example:
+
+hsi2c@12ca0000 {
+	compatible = "samsung,exynos5250-hsi2c";
+	reg = <0x12ca0000 0x100>;
+	interrupts = <56>;
+	clock-frequency = <100000>;
+
+	pinctrl-0 = <&i2c4_bus>;
+	pinctrl-names = "default";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	s2mps11_pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-fsi.txt b/Documentation/devicetree/bindings/i2c/i2c-fsi.txt
new file mode 100644
index 000000000..b1be2ceb7
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-fsi.txt
@@ -0,0 +1,40 @@
+Device-tree bindings for FSI-attached I2C master and busses
+-----------------------------------------------------------
+
+Required properties:
+ - compatible = "ibm,i2c-fsi";
+ - reg = < address size >;		: The FSI CFAM address and address
+					  space size.
+ - #address-cells = <1>;		: Number of address cells in child
+					  nodes.
+ - #size-cells = <0>;			: Number of size cells in child nodes.
+ - child nodes				: Nodes to describe busses off the I2C
+					  master.
+
+Child node required properties:
+ - reg = < port number >		: The port number on the I2C master.
+
+Child node optional properties:
+ - child nodes				: Nodes to describe devices on the I2C
+					  bus.
+
+Examples:
+
+    i2c@1800 {
+        compatible = "ibm,i2c-fsi";
+        reg = < 0x1800 0x400 >;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        i2c-bus@0 {
+            reg = <0>;
+        };
+
+        i2c-bus@1 {
+            reg = <1>;
+
+            eeprom@50 {
+                compatible = "vendor,dev-name";
+            };
+        };
+    };
diff --git a/Documentation/devicetree/bindings/i2c/i2c-gate.txt b/Documentation/devicetree/bindings/i2c/i2c-gate.txt
new file mode 100644
index 000000000..1846d236e
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-gate.txt
@@ -0,0 +1,41 @@
+An i2c gate is useful to e.g. reduce the digital noise for RF tuners connected
+to the i2c bus. Gates are similar to arbitrators in that you need to perform
+some kind of operation to access the i2c bus past the arbitrator/gate, but
+there are no competing masters to consider for gates and therefore there is
+no arbitration happening for gates.
+
+Common i2c gate properties.
+
+- i2c-gate child node
+
+Required properties for the i2c-gate child node:
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties for i2c-gate child node:
+- Child nodes conforming to i2c bus binding
+
+
+Example :
+
+	/*
+	   An Invensense mpu9150 at address 0x68 featuring an on-chip Asahi
+	   Kasei ak8975 compass behind a gate.
+	 */
+
+	mpu9150@68 {
+		compatible = "invensense,mpu9150";
+		reg = <0x68>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <18 1>;
+
+		i2c-gate {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ax8975@c {
+				compatible = "ak,ak8975";
+				reg = <0x0c>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-gpio.txt
new file mode 100644
index 000000000..38a05562d
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-gpio.txt
@@ -0,0 +1,46 @@
+Device-Tree bindings for i2c gpio driver
+
+Required properties:
+	- compatible = "i2c-gpio";
+	- sda-gpios: gpio used for the sda signal, this should be flagged as
+	  active high using open drain with (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)
+	  from <dt-bindings/gpio/gpio.h> since the signal is by definition
+	  open drain.
+	- scl-gpios: gpio used for the scl signal, this should be flagged as
+	  active high using open drain with (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)
+	  from <dt-bindings/gpio/gpio.h> since the signal is by definition
+	  open drain.
+
+Optional properties:
+	- i2c-gpio,scl-output-only: scl as output only
+	- i2c-gpio,delay-us: delay between GPIO operations (may depend on each platform)
+	- i2c-gpio,timeout-ms: timeout to get data
+
+Deprecated properties, do not use in new device tree sources:
+	- gpios: sda and scl gpio, alternative for {sda,scl}-gpios
+	- i2c-gpio,sda-open-drain: this means that something outside of our
+	  control has put the GPIO line used for SDA into open drain mode, and
+	  that something is not the GPIO chip. It is essentially an
+	  inconsistency flag.
+	- i2c-gpio,scl-open-drain: this means that something outside of our
+	  control has put the GPIO line used for SCL into open drain mode, and
+	  that something is not the GPIO chip. It is essentially an
+	  inconsistency flag.
+
+Example nodes:
+
+#include <dt-bindings/gpio/gpio.h>
+
+i2c@0 {
+	compatible = "i2c-gpio";
+	sda-gpios = <&pioA 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&pioA 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+	i2c-gpio,delay-us = <2>;	/* ~100 kHz */
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	rv3029c2@56 {
+		compatible = "rv3029c2";
+		reg = <0x56>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt b/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt
new file mode 100644
index 000000000..f98b37401
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-hix5hd2.txt
@@ -0,0 +1,24 @@
+I2C for Hisilicon hix5hd2 chipset platform
+
+Required properties:
+- compatible: Must be "hisilicon,hix5hd2-i2c"
+- reg: physical base address of the controller and length of memory mapped
+     region.
+- interrupts: interrupt number to the cpu.
+- #address-cells = <1>;
+- #size-cells = <0>;
+- clocks: phandles to input clocks.
+
+Optional properties:
+- clock-frequency: Desired I2C bus frequency in Hz, otherwise defaults to 100000
+- Child nodes conforming to i2c bus binding
+
+Examples:
+I2C0@f8b10000 {
+	compatible = "hisilicon,hix5hd2-i2c";
+	reg = <0xf8b10000 0x1000>;
+	interrupts = <0 38 4>;
+	clocks = <&clock HIX5HD2_I2C0_RST>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+}
diff --git a/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt
new file mode 100644
index 000000000..b6461602d
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-img-scb.txt
@@ -0,0 +1,26 @@
+IMG Serial Control Bus (SCB) I2C Controller
+
+Required Properties:
+- compatible: "img,scb-i2c"
+- reg: Physical base address and length of controller registers
+- interrupts: Interrupt number used by the controller
+- clocks : Should contain a clock specifier for each entry in clock-names
+- clock-names : Should contain the following entries:
+                "scb", for the SCB core clock.
+                "sys", for the system clock.
+- clock-frequency: The I2C bus frequency in Hz
+- #address-cells: Should be <1>
+- #size-cells: Should be <0>
+
+Example:
+
+i2c@18100000 {
+	compatible = "img,scb-i2c";
+	reg = <0x18100000 0x200>;
+	interrupts = <GIC_SHARED 2 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&i2c0_clk>, <&system_clk>;
+	clock-names = "scb", "sys";
+	clock-frequency = <400000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt
new file mode 100644
index 000000000..091c8dfd3
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-imx-lpi2c.txt
@@ -0,0 +1,18 @@
+* Freescale Low Power Inter IC (LPI2C) for i.MX
+
+Required properties:
+- compatible :
+  - "fsl,imx7ulp-lpi2c" for LPI2C compatible with the one integrated on i.MX7ULP soc
+- reg : address and length of the lpi2c master registers
+- interrupts : lpi2c interrupt
+- clocks : lpi2c clock specifier
+
+Examples:
+
+lpi2c7: lpi2c7@40a50000 {
+	compatible = "fsl,imx7ulp-lpi2c";
+	reg = <0x40A50000 0x10000>;
+	interrupt-parent = <&intc>;
+	interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&clks IMX7ULP_CLK_LPI2C7>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-imx.txt b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
new file mode 100644
index 000000000..b96754459
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-imx.txt
@@ -0,0 +1,49 @@
+* Freescale Inter IC (I2C) and High Speed Inter IC (HS-I2C) for i.MX
+
+Required properties:
+- compatible :
+  - "fsl,imx1-i2c" for I2C compatible with the one integrated on i.MX1 SoC
+  - "fsl,imx21-i2c" for I2C compatible with the one integrated on i.MX21 SoC
+  - "fsl,vf610-i2c" for I2C compatible with the one integrated on Vybrid vf610 SoC
+- reg : Should contain I2C/HS-I2C registers location and length
+- interrupts : Should contain I2C/HS-I2C interrupt
+- clocks : Should contain the I2C/HS-I2C clock specifier
+
+Optional properties:
+- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
+  The absence of the property indicates the default frequency 100 kHz.
+- dmas: A list of two dma specifiers, one for each entry in dma-names.
+- dma-names: should contain "tx" and "rx".
+- scl-gpios: specify the gpio related to SCL pin
+- sda-gpios: specify the gpio related to SDA pin
+- pinctrl: add extra pinctrl to configure i2c pins to gpio function for i2c
+  bus recovery, call it "gpio" state
+
+Examples:
+
+i2c@83fc4000 { /* I2C2 on i.MX51 */
+	compatible = "fsl,imx51-i2c", "fsl,imx21-i2c";
+	reg = <0x83fc4000 0x4000>;
+	interrupts = <63>;
+};
+
+i2c@70038000 { /* HS-I2C on i.MX51 */
+	compatible = "fsl,imx51-i2c", "fsl,imx21-i2c";
+	reg = <0x70038000 0x4000>;
+	interrupts = <64>;
+	clock-frequency = <400000>;
+};
+
+i2c0: i2c@40066000 { /* i2c0 on vf610 */
+	compatible = "fsl,vf610-i2c";
+	reg = <0x40066000 0x1000>;
+	interrupts =<0 71 0x04>;
+	dmas = <&edma0 0 50>,
+		<&edma0 0 51>;
+	dma-names = "rx","tx";
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>;
+	sda-gpios = <&gpio5 27 GPIO_ACTIVE_HIGH>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt b/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt
new file mode 100644
index 000000000..3738cfbf8
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-jz4780.txt
@@ -0,0 +1,31 @@
+* Ingenic JZ4780 I2C Bus controller
+
+Required properties:
+- compatible: should be "ingenic,jz4780-i2c"
+- reg: Should contain the address & size of the I2C controller registers.
+- interrupts: Should specify the interrupt provided by parent.
+- clocks: Should contain a single clock specifier for the JZ4780 I2C clock.
+- clock-frequency: desired I2C bus clock frequency in Hz.
+
+Recommended properties:
+- pinctrl-names: should be "default";
+- pinctrl-0: phandle to pinctrl function
+
+Example
+
+/ {
+	i2c4: i2c4@10054000 {
+		compatible = "ingenic,jz4780-i2c";
+		reg = <0x10054000 0x1000>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <56>;
+
+		clocks = <&cgu JZ4780_CLK_SMB4>;
+		clock-frequency = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_i2c4_data>;
+
+	};
+};
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-lpc2k.txt b/Documentation/devicetree/bindings/i2c/i2c-lpc2k.txt
new file mode 100644
index 000000000..4101aa621
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-lpc2k.txt
@@ -0,0 +1,33 @@
+NXP I2C controller for LPC2xxx/178x/18xx/43xx
+
+Required properties:
+ - compatible: must be "nxp,lpc1788-i2c"
+ - reg: physical address and length of the device registers
+ - interrupts: a single interrupt specifier
+ - clocks: clock for the device
+ - #address-cells: should be <1>
+ - #size-cells: should be <0>
+
+Optional properties:
+- clock-frequency: the desired I2C bus clock frequency in Hz; in
+  absence of this property the default value is used (100 kHz).
+
+Example:
+i2c0: i2c@400a1000 {
+	compatible = "nxp,lpc1788-i2c";
+	reg = <0x400a1000 0x1000>;
+	interrupts = <18>;
+	clocks = <&ccu1 CLK_APB1_I2C0>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+
+	lm75@48 {
+		compatible = "nxp,lm75";
+		reg = <0x48>;
+	};
+};
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-meson.txt b/Documentation/devicetree/bindings/i2c/i2c-meson.txt
new file mode 100644
index 000000000..13d410de0
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-meson.txt
@@ -0,0 +1,30 @@
+Amlogic Meson I2C controller
+
+Required properties:
+ - compatible: must be:
+	"amlogic,meson6-i2c" for Meson8 and compatible SoCs
+	"amlogic,meson-gxbb-i2c" for GXBB and compatible SoCs
+	"amlogic,meson-axg-i2c"for AXG and compatible SoCs
+
+ - reg: physical address and length of the device registers
+ - interrupts: a single interrupt specifier
+ - clocks: clock for the device
+ - #address-cells: should be <1>
+ - #size-cells: should be <0>
+
+For details regarding the following core I2C bindings see also i2c.txt.
+
+Optional properties:
+- clock-frequency: the desired I2C bus clock frequency in Hz; in
+  absence of this property the default value is used (100 kHz).
+
+Examples:
+
+	i2c@c8100500 {
+		compatible = "amlogic,meson6-i2c";
+		reg = <0xc8100500 0x20>;
+		interrupts = <0 92 1>;
+		clocks = <&clk81>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mpc.txt b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt
new file mode 100644
index 000000000..42a390526
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mpc.txt
@@ -0,0 +1,62 @@
+* I2C
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "fsl,CHIP-i2c" where CHIP is the name of a
+   compatible processor, e.g. mpc8313, mpc8543, mpc8544, mpc5121,
+   mpc5200 or mpc5200b. For the mpc5121, an additional node
+   "fsl,mpc5121-i2c-ctrl" is required as shown in the example below.
+
+Recommended properties :
+
+ - interrupts : <a b> where a is the interrupt number and b is a
+   field that represents an encoding of the sense and level
+   information for the interrupt.  This should be encoded based on
+   the information in section 2) depending on the type of interrupt
+   controller you have.
+ - fsl,preserve-clocking : boolean; if defined, the clock settings
+   from the bootloader are preserved (not touched).
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+ - fsl,timeout : I2C bus timeout in microseconds.
+
+Examples :
+
+	/* MPC5121 based board */
+	i2c@1740 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc5121-i2c", "fsl-i2c";
+		reg = <0x1740 0x20>;
+		interrupts = <11 0x8>;
+		interrupt-parent = <&ipic>;
+		clock-frequency = <100000>;
+	};
+
+	i2ccontrol@1760 {
+		compatible = "fsl,mpc5121-i2c-ctrl";
+		reg = <0x1760 0x8>;
+	};
+
+	/* MPC5200B based board */
+	i2c@3d00 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c";
+		reg = <0x3d00 0x40>;
+		interrupts = <2 15 0>;
+		interrupt-parent = <&mpc5200_pic>;
+		fsl,preserve-clocking;
+	};
+
+	/* MPC8544 base board */
+	i2c@3100 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,mpc8544-i2c", "fsl-i2c";
+		reg = <0x3100 0x100>;
+		interrupts = <43 2>;
+		interrupt-parent = <&mpic>;
+		clock-frequency = <400000>;
+		fsl,timeout = <10000>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mtk.txt b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt
new file mode 100644
index 000000000..e199695b1
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mtk.txt
@@ -0,0 +1,43 @@
+* MediaTek's I2C controller
+
+The MediaTek's I2C controller is used to interface with I2C devices.
+
+Required properties:
+  - compatible: value should be either of the following.
+      "mediatek,mt2701-i2c", "mediatek,mt6577-i2c": for MediaTek MT2701
+      "mediatek,mt2712-i2c": for MediaTek MT2712
+      "mediatek,mt6577-i2c": for MediaTek MT6577
+      "mediatek,mt6589-i2c": for MediaTek MT6589
+      "mediatek,mt7622-i2c": for MediaTek MT7622
+      "mediatek,mt7623-i2c", "mediatek,mt6577-i2c": for MediaTek MT7623
+      "mediatek,mt8173-i2c": for MediaTek MT8173
+  - reg: physical base address of the controller and dma base, length of memory
+    mapped region.
+  - interrupts: interrupt number to the cpu.
+  - clock-div: the fixed value for frequency divider of clock source in i2c
+    module. Each IC may be different.
+  - clocks: clock name from clock manager
+  - clock-names: Must include "main" and "dma", if enable have-pmic need include
+    "pmic" extra.
+
+Optional properties:
+  - clock-frequency: Frequency in Hz of the bus when transfer, the default value
+    is 100000.
+  - mediatek,have-pmic: platform can control i2c form special pmic side.
+    Only mt6589 and mt8135 support this feature.
+  - mediatek,use-push-pull: IO config use push-pull mode.
+
+Example:
+
+	i2c0: i2c@1100d000 {
+			compatible = "mediatek,mt6577-i2c";
+			reg = <0x1100d000 0x70>,
+			      <0x11000300 0x80>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_LOW>;
+			clock-frequency = <400000>;
+			mediatek,have-pmic;
+			clock-div = <16>;
+			clocks = <&i2c0_ck>, <&ap_dma_ck>;
+			clock-names = "main", "dma";
+	};
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
new file mode 100644
index 000000000..21da3ecbb
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpio.txt
@@ -0,0 +1,81 @@
+GPIO-based I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses GPIOs to
+route the I2C signals.
+
+                                  +-----+  +-----+
+                                  | dev |  | dev |
+    +------------+                +-----+  +-----+
+    | SoC        |                   |        |
+    |            |          /--------+--------+
+    |   +------+ |  +------+    child bus A, on GPIO value set to 0
+    |   | I2C  |-|--| Mux  |
+    |   +------+ |  +--+---+    child bus B, on GPIO value set to 1
+    |            |     |    \----------+--------+--------+
+    |   +------+ |     |               |        |        |
+    |   | GPIO |-|-----+            +-----+  +-----+  +-----+
+    |   +------+ |                  | dev |  | dev |  | dev |
+    +------------+                  +-----+  +-----+  +-----+
+
+Required properties:
+- compatible: i2c-mux-gpio
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+- mux-gpios: list of gpios used to control the muxer
+* Standard I2C mux properties. See i2c-mux.txt in this directory.
+* I2C child bus nodes. See i2c-mux.txt in this directory.
+
+Optional properties:
+- idle-state: value to set the muxer to when idle. When no value is
+  given, it defaults to the last value used.
+
+For each i2c child node, an I2C child bus will be created. They will
+be numbered based on their order in the device tree.
+
+Whenever an access is made to a device on a child bus, the value set
+in the relevant node's reg property will be output using the list of
+GPIOs, the first in the list holding the least-significant value.
+
+If an idle state is defined, using the idle-state (optional) property,
+whenever an access is not being made to a device on a child bus, the
+GPIOs will be set according to the idle value.
+
+If an idle state is not defined, the most recently used value will be
+left programmed into hardware whenever no access is being made to a
+device on a child bus.
+
+Example:
+	i2cmux {
+		compatible = "i2c-mux-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-gpios = <&gpio1 22 0 &gpio1 23 0>;
+		i2c-parent = <&i2c1>;
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ssd1307: oled@3c {
+				compatible = "solomon,ssd1307fb-i2c";
+				reg = <0x3c>;
+				pwms = <&pwm 4 3000>;
+				reset-gpios = <&gpio2 7 1>;
+				reset-active-low;
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pca9555: pca9555@20 {
+				compatible = "nxp,pca9555";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x20>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt
new file mode 100644
index 000000000..2907dab56
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-gpmux.txt
@@ -0,0 +1,99 @@
+General Purpose I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses a mux controller
+from the mux subsystem to route the I2C signals.
+
+                                  .-----.  .-----.
+                                  | dev |  | dev |
+    .------------.                '-----'  '-----'
+    | SoC        |                   |        |
+    |            |          .--------+--------'
+    |   .------. |  .------+    child bus A, on MUX value set to 0
+    |   | I2C  |-|--| Mux  |
+    |   '------' |  '--+---+    child bus B, on MUX value set to 1
+    |   .------. |     |    '----------+--------+--------.
+    |   | MUX- | |     |               |        |        |
+    |   | Ctrl |-|-----+            .-----.  .-----.  .-----.
+    |   '------' |                  | dev |  | dev |  | dev |
+    '------------'                  '-----'  '-----'  '-----'
+
+Required properties:
+- compatible: i2c-mux
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+- mux-controls: The phandle of the mux controller to use for operating the
+  mux.
+* Standard I2C mux properties. See i2c-mux.txt in this directory.
+* I2C child bus nodes. See i2c-mux.txt in this directory. The sub-bus number
+  is also the mux-controller state described in ../mux/mux-controller.txt
+
+Optional properties:
+- mux-locked: If present, explicitly allow unrelated I2C transactions on the
+  parent I2C adapter at these times:
+   + during setup of the multiplexer
+   + between setup of the multiplexer and the child bus I2C transaction
+   + between the child bus I2C transaction and releasing of the multiplexer
+   + during releasing of the multiplexer
+  However, I2C transactions to devices behind all I2C multiplexers connected
+  to the same parent adapter that this multiplexer is connected to are blocked
+  for the full duration of the complete multiplexed I2C transaction (i.e.
+  including the times covered by the above list).
+  If mux-locked is not present, the multiplexer is assumed to be parent-locked.
+  This means that no unrelated I2C transactions are allowed on the parent I2C
+  adapter for the complete multiplexed I2C transaction.
+  The properties of mux-locked and parent-locked multiplexers are discussed
+  in more detail in Documentation/i2c/i2c-topology.
+
+For each i2c child node, an I2C child bus will be created. They will
+be numbered based on their order in the device tree.
+
+Whenever an access is made to a device on a child bus, the value set
+in the relevant node's reg property will be set as the state in the
+mux controller.
+
+Example:
+	mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+
+		mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
+			    <&pioA 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	i2c-mux {
+		compatible = "i2c-mux";
+		mux-locked;
+		i2c-parent = <&i2c1>;
+
+		mux-controls = <&mux>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ssd1307: oled@3c {
+				compatible = "solomon,ssd1307fb-i2c";
+				reg = <0x3c>;
+				pwms = <&pwm 4 3000>;
+				reset-gpios = <&gpio2 7 1>;
+				reset-active-low;
+			};
+		};
+
+		i2c@3 {
+			reg = <3>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pca9555: pca9555@20 {
+				compatible = "nxp,pca9555";
+				gpio-controller;
+				#gpio-cells = <2>;
+				reg = <0x20>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt
new file mode 100644
index 000000000..1e98c6b3a
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-ltc4306.txt
@@ -0,0 +1,61 @@
+* Linear Technology / Analog Devices I2C bus switch
+
+Required Properties:
+
+  - compatible: Must contain one of the following.
+    "lltc,ltc4305", "lltc,ltc4306"
+  - reg: The I2C address of the device.
+
+  The following required properties are defined externally:
+
+  - Standard I2C mux properties. See i2c-mux.txt in this directory.
+  - I2C child bus nodes. See i2c-mux.txt in this directory.
+
+Optional Properties:
+
+  - enable-gpios: Reference to the GPIO connected to the enable input.
+  - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all
+    children in idle state. This is necessary for example, if there are several
+    multiplexers on the bus and the devices behind them use same I2C addresses.
+  - gpio-controller: Marks the device node as a GPIO Controller.
+  - #gpio-cells: Should be two.  The first cell is the pin number and
+	the second cell is used to specify flags.
+	See ../gpio/gpio.txt for more information.
+  - ltc,downstream-accelerators-enable: Enables the rise time accelerators
+	on the downstream port.
+  - ltc,upstream-accelerators-enable: Enables the rise time accelerators
+	on the upstream port.
+
+Example:
+
+	ltc4306: i2c-mux@4a {
+		compatible = "lltc,ltc4306";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x4a>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+
+			eeprom@50 {
+				compatible = "at,24c02";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			eeprom@50 {
+				compatible = "at,24c02";
+				reg = <0x50>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
new file mode 100644
index 000000000..ccf6c86ed
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pca954x.txt
@@ -0,0 +1,72 @@
+* NXP PCA954x I2C bus switch
+
+The driver supports NXP PCA954x and PCA984x I2C mux/switch devices.
+
+Required Properties:
+
+  - compatible: Must contain one of the following.
+    "nxp,pca9540",
+    "nxp,pca9542",
+    "nxp,pca9543",
+    "nxp,pca9544",
+    "nxp,pca9545",
+    "nxp,pca9546", "nxp,pca9846",
+    "nxp,pca9547", "nxp,pca9847",
+    "nxp,pca9548", "nxp,pca9848",
+    "nxp,pca9849"
+
+  - reg: The I2C address of the device.
+
+  The following required properties are defined externally:
+
+  - Standard I2C mux properties. See i2c-mux.txt in this directory.
+  - I2C child bus nodes. See i2c-mux.txt in this directory.
+
+Optional Properties:
+
+  - reset-gpios: Reference to the GPIO connected to the reset input.
+  - i2c-mux-idle-disconnect: Boolean; if defined, forces mux to disconnect all
+    children in idle state. This is necessary for example, if there are several
+    multiplexers on the bus and the devices behind them use same I2C addresses.
+  - interrupts: Interrupt mapping for IRQ.
+  - interrupt-controller: Marks the device node as an interrupt controller.
+  - #interrupt-cells : Should be two.
+    - first cell is the pin number
+    - second cell is used to specify flags.
+    See also Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+Example:
+
+	i2c-switch@74 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x74>;
+
+		interrupt-parent = <&ipic>;
+		interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			eeprom@54 {
+				compatible = "at,24c08";
+				reg = <0x54>;
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			rtc@51 {
+				compatible = "nxp,pcf8563";
+				reg = <0x51>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt
new file mode 100644
index 000000000..33119a98e
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-pinctrl.txt
@@ -0,0 +1,93 @@
+Pinctrl-based I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses pin multiplexing to
+route the I2C signals, and represents the pin multiplexing configuration
+using the pinctrl device tree bindings.
+
+                                 +-----+  +-----+
+                                 | dev |  | dev |
+    +------------------------+   +-----+  +-----+
+    | SoC                    |      |        |
+    |                   /----|------+--------+
+    |   +---+   +------+     | child bus A, on first set of pins
+    |   |I2C|---|Pinmux|     |
+    |   +---+   +------+     | child bus B, on second set of pins
+    |                   \----|------+--------+--------+
+    |                        |      |        |        |
+    +------------------------+  +-----+  +-----+  +-----+
+                                | dev |  | dev |  | dev |
+                                +-----+  +-----+  +-----+
+
+Required properties:
+- compatible: i2c-mux-pinctrl
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+
+Also required are:
+
+* Standard pinctrl properties that specify the pin mux state for each child
+  bus. See ../pinctrl/pinctrl-bindings.txt.
+
+* Standard I2C mux properties. See i2c-mux.txt in this directory.
+
+* I2C child bus nodes. See i2c-mux.txt in this directory.
+
+For each named state defined in the pinctrl-names property, an I2C child bus
+will be created. I2C child bus numbers are assigned based on the index into
+the pinctrl-names property.
+
+The only exception is that no bus will be created for a state named "idle". If
+such a state is defined, it must be the last entry in pinctrl-names. For
+example:
+
+	pinctrl-names = "ddc", "pta", "idle"  ->  ddc = bus 0, pta = bus 1
+	pinctrl-names = "ddc", "idle", "pta"  ->  Invalid ("idle" not last)
+	pinctrl-names = "idle", "ddc", "pta"  ->  Invalid ("idle" not last)
+
+Whenever an access is made to a device on a child bus, the relevant pinctrl
+state will be programmed into hardware.
+
+If an idle state is defined, whenever an access is not being made to a device
+on a child bus, the idle pinctrl state will be programmed into hardware.
+
+If an idle state is not defined, the most recently used pinctrl state will be
+left programmed into hardware whenever no access is being made of a device on
+a child bus.
+
+Example:
+
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&i2c1>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom {
+				compatible = "eeprom";
+				reg = <0x50>;
+			};
+		};
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom {
+				compatible = "eeprom";
+				reg = <0x50>;
+			};
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt
new file mode 100644
index 000000000..de00d7fc4
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux-reg.txt
@@ -0,0 +1,74 @@
+Register-based I2C Bus Mux
+
+This binding describes an I2C bus multiplexer that uses a single register
+to route the I2C signals.
+
+Required properties:
+- compatible: i2c-mux-reg
+- i2c-parent: The phandle of the I2C bus that this multiplexer's master-side
+  port is connected to.
+* Standard I2C mux properties. See i2c-mux.txt in this directory.
+* I2C child bus nodes. See i2c-mux.txt in this directory.
+
+Optional properties:
+- reg: this pair of <offset size> specifies the register to control the mux.
+  The <offset size> depends on its parent node. It can be any memory-mapped
+  address. The size must be either 1, 2, or 4 bytes. If reg is omitted, the
+  resource of this device will be used.
+- little-endian: The existence indicates the register is in little endian.
+- big-endian: The existence indicates the register is in big endian.
+  If both little-endian and big-endian are omitted, the endianness of the
+  CPU will be used.
+- write-only: The existence indicates the register is write-only.
+- idle-state: value to set the muxer to when idle. When no value is
+  given, it defaults to the last value used.
+
+Whenever an access is made to a device on a child bus, the value set
+in the relevant node's reg property will be output to the register.
+
+If an idle state is defined, using the idle-state (optional) property,
+whenever an access is not being made to a device on a child bus, the
+register will be set according to the idle value.
+
+If an idle state is not defined, the most recently used value will be
+left programmed into the register.
+
+Example of a mux on PCIe card, the host is a powerpc SoC (big endian):
+
+	i2c-mux {
+		/* the <offset size> depends on the address translation
+		 * of the parent device. If omitted, device resource
+		 * will be used instead. The size is to determine
+		 * whether iowrite32, iowrite16, or iowrite8 will be used.
+		 */
+		reg = <0x6028 0x4>;
+		little-endian;		/* little endian register on PCIe */
+		compatible = "i2c-mux-reg";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-parent = <&i2c1>;
+		i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			si5338: clock-generator@70 {
+				compatible = "silabs,si5338";
+				reg = <0x70>;
+				/* other stuff */
+			};
+		};
+
+		i2c@1 {
+			/* data is written using iowrite32 */
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			si5338: clock-generator@70 {
+				compatible = "silabs,si5338";
+				reg = <0x70>;
+				/* other stuff */
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mux.txt b/Documentation/devicetree/bindings/i2c/i2c-mux.txt
new file mode 100644
index 000000000..b38f58a1c
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mux.txt
@@ -0,0 +1,73 @@
+Common i2c bus multiplexer/switch properties.
+
+An i2c bus multiplexer/switch will have several child busses that are
+numbered uniquely in a device dependent manner.  The nodes for an i2c bus
+multiplexer/switch will have one child node for each child bus.
+
+Optional properties:
+- #address-cells = <1>;
+   This property is required if the i2c-mux child node does not exist.
+
+- #size-cells = <0>;
+   This property is required if the i2c-mux child node does not exist.
+
+- i2c-mux
+   For i2c multiplexers/switches that have child nodes that are a mixture
+   of both i2c child busses and other child nodes, the 'i2c-mux' subnode
+   can be used for populating the i2c child busses.  If an 'i2c-mux'
+   subnode is present, only subnodes of this will be considered as i2c
+   child busses.
+
+Required properties for the i2c-mux child node:
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Required properties for i2c child bus nodes:
+- #address-cells = <1>;
+- #size-cells = <0>;
+- reg : The sub-bus number.
+
+Optional properties for i2c child bus nodes:
+- Other properties specific to the multiplexer/switch hardware.
+- Child nodes conforming to i2c bus binding
+
+
+Example :
+
+	/*
+	   An NXP pca9548 8 channel I2C multiplexer at address 0x70
+	   with two NXP pca8574 GPIO expanders attached, one each to
+	   ports 3 and 4.
+	 */
+
+	mux@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			gpio1: gpio@38 {
+				compatible = "nxp,pca8574";
+				reg = <0x38>;
+				#gpio-cells = <2>;
+				gpio-controller;
+			};
+		};
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			gpio2: gpio@38 {
+				compatible = "nxp,pca8574";
+				reg = <0x38>;
+				#gpio-cells = <2>;
+				gpio-controller;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt
new file mode 100644
index 000000000..0ffe65a31
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mv64xxx.txt
@@ -0,0 +1,64 @@
+
+* Marvell MV64XXX I2C controller
+
+Required properties :
+
+ - reg             : Offset and length of the register set for the device
+ - compatible      : Should be either:
+                     - "allwinner,sun4i-a10-i2c"
+                     - "allwinner,sun6i-a31-i2c"
+                     - "marvell,mv64xxx-i2c"
+                     - "marvell,mv78230-i2c"
+                     - "marvell,mv78230-a0-i2c"
+                       * Note: Only use "marvell,mv78230-a0-i2c" for a
+                         very rare, initial version of the SoC which
+                         had broken offload support.  Linux
+                         auto-detects this and sets it appropriately.
+ - interrupts      : The interrupt number
+
+Optional properties :
+
+ - clock-frequency : Desired I2C bus clock frequency in Hz. If not set the
+default frequency is 100kHz
+
+ - resets          : phandle to the parent reset controller. Mandatory
+                     whenever you're using the "allwinner,sun6i-a31-i2c"
+                     compatible.
+
+ - clocks:	   : pointers to the reference clocks for this device, the
+		     first one is the one used for the clock on the i2c bus,
+		     the second one is the clock used to acces the registers
+		     of the controller
+
+ - clock-names	   : names of used clocks, mandatory if the second clock is
+		     used, the name must be "core", and "reg" (the latter is
+		     only for Armada 7K/8K).
+
+Examples:
+
+	i2c@11000 {
+		compatible = "marvell,mv64xxx-i2c";
+		reg = <0x11000 0x20>;
+		interrupts = <29>;
+		clock-frequency = <100000>;
+	};
+
+For the Armada XP:
+
+	i2c@11000 {
+		compatible = "marvell,mv78230-i2c", "marvell,mv64xxx-i2c";
+		reg = <0x11000 0x100>;
+		interrupts = <29>;
+		clock-frequency = <100000>;
+	};
+
+For the Armada 7040:
+
+	i2c@701000 {
+		compatible = "marvell,mv78230-i2c";
+		reg = <0x701000 0x20>;
+		interrupts = <29>;
+		clock-frequency = <100000>;
+		clock-names = "core", "reg";
+		clocks = <&core_clock>, <&reg_clock>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-mxs.txt b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
new file mode 100644
index 000000000..4e1c8ac01
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-mxs.txt
@@ -0,0 +1,25 @@
+* Freescale MXS Inter IC (I2C) Controller
+
+Required properties:
+- compatible: Should be "fsl,<chip>-i2c"
+- reg: Should contain registers location and length
+- interrupts: Should contain ERROR interrupt number
+- clock-frequency: Desired I2C bus clock frequency in Hz.
+                   Only 100000Hz and 400000Hz modes are supported.
+- dmas: DMA specifier, consisting of a phandle to DMA controller node
+  and I2C DMA channel ID.
+  Refer to dma.txt and fsl-mxs-dma.txt for details.
+- dma-names: Must be "rx-tx".
+
+Examples:
+
+i2c0: i2c@80058000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-i2c";
+	reg = <0x80058000 2000>;
+	interrupts = <111>;
+	clock-frequency = <100000>;
+	dmas = <&dma_apbx 6>;
+	dma-names = "rx-tx";
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt
new file mode 100644
index 000000000..72065b0ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-nomadik.txt
@@ -0,0 +1,23 @@
+I2C for Nomadik based systems
+
+Required (non-standard) properties:
+ - Nil
+
+Recommended (non-standard) properties:
+ - clock-frequency : Maximum bus clock frequency for the device
+
+Optional (non-standard) properties:
+ - Nil
+
+Example :
+
+i2c@80004000 {
+        compatible = "stericsson,db8500-i2c", "st,nomadik-i2c";
+        reg = <0x80004000 0x1000>;
+        interrupts = <0 21 0x4>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        v-i2c-supply = <&db8500_vape_reg>;
+
+        clock-frequency = <400000>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-ocores.txt b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt
new file mode 100644
index 000000000..17bef9a34
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-ocores.txt
@@ -0,0 +1,69 @@
+Device tree configuration for i2c-ocores
+
+Required properties:
+- compatible      : "opencores,i2c-ocores" or "aeroflexgaisler,i2cmst"
+- reg             : bus address start and address range size of device
+- interrupts      : interrupt number
+- clocks          : handle to the controller clock; see the note below.
+                    Mutually exclusive with opencores,ip-clock-frequency
+- opencores,ip-clock-frequency: frequency of the controller clock in Hz;
+                    see the note below. Mutually exclusive with clocks
+- #address-cells  : should be <1>
+- #size-cells     : should be <0>
+
+Optional properties:
+- clock-frequency : frequency of bus clock in Hz; see the note below.
+                    Defaults to 100 KHz when the property is not specified
+- reg-shift       : device register offsets are shifted by this value
+- reg-io-width    : io register width in bytes (1, 2 or 4)
+- regstep         : deprecated, use reg-shift above
+
+Note
+clock-frequency property is meant to control the bus frequency for i2c bus
+drivers, but it was incorrectly used to specify i2c controller input clock
+frequency. So the following rules are set to fix this situation:
+- if clock-frequency is present and neither opencores,ip-clock-frequency nor
+  clocks are, then clock-frequency specifies i2c controller clock frequency.
+  This is to keep backwards compatibility with setups using old DTB. i2c bus
+  frequency is fixed at 100 KHz.
+- if clocks is present it specifies i2c controller clock. clock-frequency
+  property specifies i2c bus frequency.
+- if opencores,ip-clock-frequency is present it specifies i2c controller
+  clock frequency. clock-frequency property specifies i2c bus frequency.
+
+Examples:
+
+	i2c0: ocores@a0000000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "opencores,i2c-ocores";
+		reg = <0xa0000000 0x8>;
+		interrupts = <10>;
+		opencores,ip-clock-frequency = <20000000>;
+
+		reg-shift = <0>;	/* 8 bit registers */
+		reg-io-width = <1>;	/* 8 bit read/write */
+
+		dummy@60 {
+			compatible = "dummy";
+			reg = <0x60>;
+		};
+	};
+or
+	i2c0: ocores@a0000000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "opencores,i2c-ocores";
+		reg = <0xa0000000 0x8>;
+		interrupts = <10>;
+		clocks = <&osc>;
+		clock-frequency = <400000>; /* i2c bus frequency 400 KHz */
+
+		reg-shift = <0>;	/* 8 bit registers */
+		reg-io-width = <1>;	/* 8 bit read/write */
+
+		dummy@60 {
+			compatible = "dummy";
+			reg = <0x60>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-octeon.txt b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt
new file mode 100644
index 000000000..872d485df
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-octeon.txt
@@ -0,0 +1,40 @@
+* Two Wire Serial Interface (TWSI) / I2C
+
+- compatible: "cavium,octeon-3860-twsi"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+  or
+
+  compatible: "cavium,octeon-7890-twsi"
+
+  Compatibility with cn78XX SOCs.
+
+- reg: The base address of the TWSI/I2C bus controller register bank.
+
+- #address-cells: Must be <1>.
+
+- #size-cells: Must be <0>.  I2C addresses have no size component.
+
+- interrupts: A single interrupt specifier.
+
+- clock-frequency: The I2C bus clock rate in Hz.
+
+Example:
+	twsi0: i2c@1180000001000 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "cavium,octeon-3860-twsi";
+		reg = <0x11800 0x00001000 0x0 0x200>;
+		interrupts = <0 45>;
+		clock-frequency = <100000>;
+
+		rtc@68 {
+			compatible = "dallas,ds1337";
+			reg = <0x68>;
+		};
+		tmp@4c {
+			compatible = "ti,tmp421";
+			reg = <0x4c>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-omap.txt b/Documentation/devicetree/bindings/i2c/i2c-omap.txt
new file mode 100644
index 000000000..7e49839d4
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-omap.txt
@@ -0,0 +1,31 @@
+I2C for OMAP platforms
+
+Required properties :
+- compatible : Must be "ti,omap2420-i2c", "ti,omap2430-i2c", "ti,omap3-i2c"
+  or "ti,omap4-i2c"
+- ti,hwmods : Must be "i2c<n>", n being the instance number (1-based)
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Recommended properties :
+- clock-frequency : Desired I2C bus clock frequency in Hz. Otherwise
+  the default 100 kHz frequency will be used.
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
+
+Note: Current implementation will fetch base address, irq and dma
+from omap hwmod data base during device registration.
+Future plan is to migrate hwmod data base contents into device tree
+blob so that, all the required data will be used from device tree dts
+file.
+
+Examples :
+
+i2c1: i2c@0 {
+    compatible = "ti,omap3-i2c";
+    #address-cells = <1>;
+    #size-cells = <0>;
+    ti,hwmods = "i2c1";
+    clock-frequency = <400000>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-opal.txt b/Documentation/devicetree/bindings/i2c/i2c-opal.txt
new file mode 100644
index 000000000..12bc61465
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-opal.txt
@@ -0,0 +1,37 @@
+Device-tree bindings for I2C OPAL driver
+----------------------------------------
+
+Most of the device node and properties layout is specific to the firmware and
+used by the firmware itself for configuring the port. From the linux
+perspective, the properties of use are "ibm,port-name" and "ibm,opal-id".
+
+Required properties:
+
+- reg: Port-id within a given master
+- compatible: must be "ibm,opal-i2c"
+- ibm,opal-id: Refers to a specific bus and used to identify it when calling
+	       the relevant OPAL functions.
+- bus-frequency: Operating frequency of the i2c bus (in HZ). Informational for
+		 linux, used by the FW though.
+
+Optional properties:
+- ibm,port-name: Firmware provides this name that uniquely identifies the i2c
+		 port.
+
+The node contains a number of other properties that are used by the FW itself
+and depend on the specific hardware implementation. The example below depicts
+a P8 on-chip bus.
+
+Example:
+
+i2c-bus@0 {
+	reg = <0x0>;
+	bus-frequency = <0x61a80>;
+	compatible = "ibm,power8-i2c-port", "ibm,opal-i2c";
+	ibm,opal-id = <0x1>;
+	ibm,port-name = "p8_00000000_e1p0";
+	#address-cells = <0x1>;
+	phandle = <0x10000006>;
+	#size-cells = <0x0>;
+	linux,phandle = <0x10000006>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-owl.txt b/Documentation/devicetree/bindings/i2c/i2c-owl.txt
new file mode 100644
index 000000000..b743fe444
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-owl.txt
@@ -0,0 +1,27 @@
+Actions Semiconductor Owl I2C controller
+
+Required properties:
+
+- compatible        : Should be "actions,s900-i2c".
+- reg               : Offset and length of the register set for the device.
+- #address-cells    : Should be 1.
+- #size-cells       : Should be 0.
+- interrupts        : A single interrupt specifier.
+- clocks            : Phandle of the clock feeding the I2C controller.
+
+Optional properties:
+
+- clock-frequency   : Desired I2C bus clock frequency in Hz. As only Normal and
+                      Fast modes are supported, possible values are 100000 and
+                      400000.
+Examples:
+
+        i2c0: i2c@e0170000 {
+                compatible = "actions,s900-i2c";
+                reg = <0 0xe0170000 0 0x1000>;
+                #address-cells = <1>;
+                #size-cells = <0>;
+                interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+                clocks = <&clock CLK_I2C0>;
+                clock-frequency = <100000>;
+        };
diff --git a/Documentation/devicetree/bindings/i2c/i2c-pca-platform.txt b/Documentation/devicetree/bindings/i2c/i2c-pca-platform.txt
new file mode 100644
index 000000000..73a693d66
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-pca-platform.txt
@@ -0,0 +1,27 @@
+* NXP PCA PCA9564/PCA9665 I2C controller
+
+The PCA9564/PCA9665 serves as an interface between most standard
+parallel-bus microcontrollers/microprocessors and the serial I2C-bus
+and allows the parallel bus system to communicate bi-directionally
+with the I2C-bus.
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : one of "nxp,pca9564" or "nxp,pca9665"
+
+Optional properties
+ - interrupts : the interrupt number
+ - reset-gpios : gpio specifier for gpio connected to RESET_N pin. As the line
+   is active low, it should be marked GPIO_ACTIVE_LOW.
+ - clock-frequency : I2C bus frequency.
+
+Example:
+	i2c0: i2c@80000 {
+		compatible = "nxp,pca9564";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x80000 0x4>;
+		reset-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		clock-frequency = <100000>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-pnx.txt b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt
new file mode 100644
index 000000000..2a59006cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-pnx.txt
@@ -0,0 +1,34 @@
+* NXP PNX I2C Controller
+
+Required properties:
+
+ - reg: Offset and length of the register set for the device
+ - compatible: should be "nxp,pnx-i2c"
+ - interrupts: configure one interrupt line
+ - #address-cells: always 1 (for i2c addresses)
+ - #size-cells: always 0
+
+Optional properties:
+
+ - clock-frequency: desired I2C bus clock frequency in Hz, Default: 100000 Hz
+
+Examples:
+
+	i2c1: i2c@400a0000 {
+		compatible = "nxp,pnx-i2c";
+		reg = <0x400a0000 0x100>;
+		interrupt-parent = <&mic>;
+		interrupts = <51 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	i2c2: i2c@400a8000 {
+		compatible = "nxp,pnx-i2c";
+		reg = <0x400a8000 0x100>;
+		interrupt-parent = <&mic>;
+		interrupts = <50 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clock-frequency = <100000>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt
new file mode 100644
index 000000000..569b16248
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-pxa-pci-ce4100.txt
@@ -0,0 +1,93 @@
+CE4100 I2C
+----------
+
+CE4100 has one PCI device which is described as the I2C-Controller. This
+PCI device has three PCI-bars, each bar contains a complete I2C
+controller. So we have a total of three independent I2C-Controllers
+which share only an interrupt line.
+The driver is probed via the PCI-ID and is gathering the information of
+attached devices from the devices tree.
+Grant Likely recommended to use the ranges property to map the PCI-Bar
+number to its physical address and to use this to find the child nodes
+of the specific I2C controller. This were his exact words:
+
+       Here's where the magic happens.  Each entry in
+       ranges describes how the parent pci address space
+       (middle group of 3) is translated to the local
+       address space (first group of 2) and the size of
+       each range (last cell).  In this particular case,
+       the first cell of the local address is chosen to be
+       1:1 mapped to the BARs, and the second is the
+       offset from be base of the BAR (which would be
+       non-zero if you had 2 or more devices mapped off
+       the same BAR)
+
+       ranges allows the address mapping to be described
+       in a way that the OS can interpret without
+       requiring custom device driver code.
+
+This is an example which is used on FalconFalls:
+------------------------------------------------
+	i2c-controller@b,2 {
+		#address-cells = <2>;
+		#size-cells = <1>;
+		compatible = "pci8086,2e68.2",
+				"pci8086,2e68",
+				"pciclass,ff0000",
+				"pciclass,ff00";
+
+		reg = <0x15a00 0x0 0x0 0x0 0x0>;
+		interrupts = <16 1>;
+
+		/* as described by Grant, the first number in the group of
+		* three is the bar number followed by the 64bit bar address
+		* followed by size of the mapping. The bar address
+		* requires also a valid translation in parents ranges
+		* property.
+		*/
+		ranges = <0 0   0x02000000 0 0xdffe0500 0x100
+			  1 0   0x02000000 0 0xdffe0600 0x100
+			  2 0   0x02000000 0 0xdffe0700 0x100>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "intel,ce4100-i2c-controller";
+
+			/* The first number in the reg property is the
+			* number of the bar
+			*/
+			reg = <0 0 0x100>;
+
+			/* This I2C controller has no devices */
+		};
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "intel,ce4100-i2c-controller";
+			reg = <1 0 0x100>;
+
+			/* This I2C controller has one gpio controller */
+			gpio@26 {
+				#gpio-cells = <2>;
+				compatible = "ti,pcf8575";
+				reg = <0x26>;
+				gpio-controller;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "intel,ce4100-i2c-controller";
+			reg = <2 0 0x100>;
+
+			gpio@26 {
+				#gpio-cells = <2>;
+				compatible = "ti,pcf8575";
+				reg = <0x26>;
+				gpio-controller;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-pxa.txt b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt
new file mode 100644
index 000000000..c30783c0e
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-pxa.txt
@@ -0,0 +1,31 @@
+* Marvell MMP I2C controller
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible : should be "mrvl,mmp-twsi" where mmp is the name of a
+   compatible processor, e.g. pxa168, pxa910, mmp2, mmp3.
+   For the pxa2xx/pxa3xx, an additional node "mrvl,pxa-i2c" is required
+   as shown in the example below.
+   For the Armada 3700, the compatible should be "marvell,armada-3700-i2c".
+
+Recommended properties :
+
+ - interrupts : the interrupt number
+ - mrvl,i2c-polling : Disable interrupt of i2c controller. Polling
+   status register of i2c controller instead.
+ - mrvl,i2c-fast-mode : Enable fast mode of i2c controller.
+
+Examples:
+	twsi1: i2c@d4011000 {
+		compatible = "mrvl,mmp-twsi";
+		reg = <0xd4011000 0x1000>;
+		interrupts = <7>;
+		mrvl,i2c-fast-mode;
+	};
+	
+	twsi2: i2c@d4025000 {
+		compatible = "mrvl,mmp-twsi";
+		reg = <0xd4025000 0x1000>;
+		interrupts = <58>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-rcar.txt b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt
new file mode 100644
index 000000000..39cd21d95
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-rcar.txt
@@ -0,0 +1,59 @@
+I2C for R-Car platforms
+
+Required properties:
+- compatible:
+	"renesas,i2c-r8a7743" if the device is a part of a R8A7743 SoC.
+	"renesas,i2c-r8a7745" if the device is a part of a R8A7745 SoC.
+	"renesas,i2c-r8a774a1" if the device is a part of a R8A774A1 SoC.
+	"renesas,i2c-r8a7778" if the device is a part of a R8A7778 SoC.
+	"renesas,i2c-r8a7779" if the device is a part of a R8A7779 SoC.
+	"renesas,i2c-r8a7790" if the device is a part of a R8A7790 SoC.
+	"renesas,i2c-r8a7791" if the device is a part of a R8A7791 SoC.
+	"renesas,i2c-r8a7792" if the device is a part of a R8A7792 SoC.
+	"renesas,i2c-r8a7793" if the device is a part of a R8A7793 SoC.
+	"renesas,i2c-r8a7794" if the device is a part of a R8A7794 SoC.
+	"renesas,i2c-r8a7795" if the device is a part of a R8A7795 SoC.
+	"renesas,i2c-r8a7796" if the device is a part of a R8A7796 SoC.
+	"renesas,i2c-r8a77965" if the device is a part of a R8A77965 SoC.
+	"renesas,i2c-r8a77970" if the device is a part of a R8A77970 SoC.
+	"renesas,i2c-r8a77980" if the device is a part of a R8A77980 SoC.
+	"renesas,i2c-r8a77990" if the device is a part of a R8A77990 SoC.
+	"renesas,i2c-r8a77995" if the device is a part of a R8A77995 SoC.
+	"renesas,rcar-gen1-i2c" for a generic R-Car Gen1 compatible device.
+	"renesas,rcar-gen2-i2c" for a generic R-Car Gen2 or RZ/G1 compatible
+				device.
+	"renesas,rcar-gen3-i2c" for a generic R-Car Gen3 or RZ/G2 compatible
+				device.
+	"renesas,i2c-rcar" (deprecated)
+
+	When compatible with the generic version, nodes must list the
+	SoC-specific version corresponding to the platform first followed
+	by the generic version.
+
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- interrupts: interrupt specifier.
+
+Optional properties:
+- clock-frequency: desired I2C bus clock frequency in Hz. The absence of this
+  property indicates the default frequency 100 kHz.
+- clocks: clock specifier.
+- dmas: Must contain a list of two references to DMA specifiers, one for
+  transmission, and one for reception.
+- dma-names: Must contain a list of two DMA names, "tx" and "rx".
+
+- i2c-scl-falling-time-ns: see i2c.txt
+- i2c-scl-internal-delay-ns: see i2c.txt
+- i2c-scl-rising-time-ns: see i2c.txt
+
+Examples :
+
+i2c0: i2c@e6508000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "renesas,i2c-r8a7791", "renesas,rcar-gen2-i2c";
+	reg = <0 0xe6508000 0 0x40>;
+	interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&mstp9_clks R8A7791_CLK_I2C0>;
+	clock-frequency = <400000>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-riic.txt b/Documentation/devicetree/bindings/i2c/i2c-riic.txt
new file mode 100644
index 000000000..0bcc4716c
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-riic.txt
@@ -0,0 +1,29 @@
+Device tree configuration for Renesas RIIC driver
+
+Required properties:
+- compatible      : "renesas,riic-<soctype>". "renesas,riic-rz" as fallback
+- reg             : address start and address range size of device
+- interrupts      : 8 interrupts (TEI, RI, TI, SPI, STI, NAKI, ALI, TMOI)
+- clock-frequency : frequency of bus clock in Hz
+- #address-cells  : should be <1>
+- #size-cells     : should be <0>
+
+Pinctrl properties might be needed, too. See there.
+
+Example:
+
+	i2c0: i2c@fcfee000 {
+		compatible = "renesas,riic-r7s72100", "renesas,riic-rz";
+		reg = <0xfcfee000 0x44>;
+		interrupts = <0 157 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 158 IRQ_TYPE_EDGE_RISING>,
+			     <0 159 IRQ_TYPE_EDGE_RISING>,
+			     <0 160 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 161 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 162 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 163 IRQ_TYPE_LEVEL_HIGH>,
+			     <0 164 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <100000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt
new file mode 100644
index 000000000..22f2eeb2c
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-rk3x.txt
@@ -0,0 +1,68 @@
+* Rockchip RK3xxx I2C controller
+
+This driver interfaces with the native I2C controller present in Rockchip
+RK3xxx SoCs.
+
+Required properties :
+
+ - reg : Offset and length of the register set for the device
+ - compatible: should be one of the following:
+   - "rockchip,rv1108-i2c": for rv1108
+   - "rockchip,rk3066-i2c": for rk3066
+   - "rockchip,rk3188-i2c": for rk3188
+   - "rockchip,rk3228-i2c": for rk3228
+   - "rockchip,rk3288-i2c": for rk3288
+   - "rockchip,rk3328-i2c", "rockchip,rk3399-i2c": for rk3328
+   - "rockchip,rk3399-i2c": for rk3399
+ - interrupts : interrupt number
+ - clocks: See ../clock/clock-bindings.txt
+   - For older hardware (rk3066, rk3188, rk3228, rk3288):
+     - There is one clock that's used both to derive the functional clock
+       for the device and as the bus clock.
+   - For newer hardware (rk3399): specified by name
+     - "i2c": This is used to derive the functional clock.
+     - "pclk": This is the bus clock.
+
+Required on RK3066, RK3188 :
+
+ - rockchip,grf : the phandle of the syscon node for the general register
+		  file (GRF)
+ - on those SoCs an alias with the correct I2C bus ID (bit offset in the GRF)
+   is also required.
+
+Optional properties :
+
+ - clock-frequency : SCL frequency to use (in Hz). If omitted, 100kHz is used.
+ - i2c-scl-rising-time-ns : Number of nanoseconds the SCL signal takes to rise
+	(t(r) in I2C specification). If not specified this is assumed to be
+	the maximum the specification allows(1000 ns for Standard-mode,
+	300 ns for Fast-mode) which might cause slightly slower communication.
+ - i2c-scl-falling-time-ns : Number of nanoseconds the SCL signal takes to fall
+	(t(f) in the I2C specification). If not specified this is assumed to
+	be the maximum the specification allows (300 ns) which might cause
+	slightly slower communication.
+ - i2c-sda-falling-time-ns : Number of nanoseconds the SDA signal takes to fall
+	(t(f) in the I2C specification). If not specified we'll use the SCL
+	value since they are the same in nearly all cases.
+
+Example:
+
+aliases {
+	i2c0 = &i2c0;
+}
+
+i2c0: i2c@2002d000 {
+	compatible = "rockchip,rk3188-i2c";
+	reg = <0x2002d000 0x1000>;
+	interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	rockchip,grf = <&grf>;
+
+	clock-names = "i2c";
+	clocks = <&cru PCLK_I2C0>;
+
+	i2c-scl-rising-time-ns = <800>;
+	i2c-scl-falling-time-ns = <100>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt
new file mode 100644
index 000000000..66ae46d3b
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-s3c2410.txt
@@ -0,0 +1,58 @@
+* Samsung's I2C controller
+
+The Samsung's I2C controller is used to interface with I2C devices.
+
+Required properties:
+  - compatible: value should be either of the following.
+      (a) "samsung, s3c2410-i2c", for i2c compatible with s3c2410 i2c.
+      (b) "samsung, s3c2440-i2c", for i2c compatible with s3c2440 i2c.
+      (c) "samsung, s3c2440-hdmiphy-i2c", for s3c2440-like i2c used
+          inside HDMIPHY block found on several samsung SoCs
+      (d) "samsung, exynos5-sata-phy-i2c", for s3c2440-like i2c used as
+	   a host to SATA PHY controller on an internal bus.
+  - reg: physical base address of the controller and length of memory mapped
+    region.
+  - interrupts: interrupt number to the cpu.
+  - samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
+
+Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
+  - Samsung GPIO variant (deprecated):
+    - gpios: The order of the gpios should be the following: <SDA, SCL>.
+      The gpio specifier depends on the gpio controller. Required in all
+      cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
+      lines are permanently wired to the respective clienta
+  - Pinctrl variant (preferred, if available):
+    - pinctrl-0: Pin control group to be used for this controller.
+    - pinctrl-names: Should contain only one value - "default".
+
+Optional properties:
+  - samsung,i2c-slave-addr: Slave address in multi-master environment. If not
+    specified, default value is 0.
+  - samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
+    specified, the default value in Hz is 100000.
+  - samsung,sysreg-phandle - handle to syscon used to control the system registers
+
+Example:
+
+	i2c@13870000 {
+		compatible = "samsung,s3c2440-i2c";
+		reg = <0x13870000 0x100>;
+		interrupts = <345>;
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <100000>;
+		/* Samsung GPIO variant begins here */
+		gpios = <&gpd1 2 0 /* SDA */
+			 &gpd1 3 0 /* SCL */>;
+		/* Samsung GPIO variant ends here */
+		/* Pinctrl variant begins here */
+		pinctrl-0 = <&i2c3_bus>;
+		pinctrl-names = "default";
+		/* Pinctrl variant ends here */
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		wm8994@1a {
+			compatible = "wlf,wm8994";
+			reg = <0x1a>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt
new file mode 100644
index 000000000..872673adf
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-sh_mobile.txt
@@ -0,0 +1,59 @@
+Device tree configuration for Renesas IIC (sh_mobile) driver
+
+Required properties:
+- compatible      :
+			- "renesas,iic-r8a73a4" (R-Mobile APE6)
+			- "renesas,iic-r8a7740" (R-Mobile A1)
+			- "renesas,iic-r8a7743" (RZ/G1M)
+			- "renesas,iic-r8a7745" (RZ/G1E)
+			- "renesas,iic-r8a774a1" (RZ/G2M)
+			- "renesas,iic-r8a7790" (R-Car H2)
+			- "renesas,iic-r8a7791" (R-Car M2-W)
+			- "renesas,iic-r8a7792" (R-Car V2H)
+			- "renesas,iic-r8a7793" (R-Car M2-N)
+			- "renesas,iic-r8a7794" (R-Car E2)
+			- "renesas,iic-r8a7795" (R-Car H3)
+			- "renesas,iic-r8a7796" (R-Car M3-W)
+			- "renesas,iic-r8a77965" (R-Car M3-N)
+			- "renesas,iic-sh73a0" (SH-Mobile AG5)
+			- "renesas,rcar-gen2-iic" (generic R-Car Gen2 or RZ/G1
+							compatible device)
+			- "renesas,rcar-gen3-iic" (generic R-Car Gen3 or RZ/G2
+							compatible device)
+			- "renesas,rmobile-iic" (generic device)
+
+			When compatible with a generic R-Car version, nodes
+			must list the SoC-specific version corresponding to
+			the platform first followed by the generic R-Car
+			version.
+
+			renesas,rmobile-iic must always follow.
+
+- reg             : address start and address range size of device
+- interrupts      : interrupt of device
+- clocks          : clock for device
+- #address-cells  : should be <1>
+- #size-cells     : should be <0>
+
+Optional properties:
+- clock-frequency : frequency of bus clock in Hz. Default 100kHz if unset.
+- dmas            : Must contain a list of two references to DMA
+		    specifiers, one for transmission, and one for
+		    reception.
+- dma-names       : Must contain a list of two DMA names, "tx" and "rx".
+
+
+Pinctrl properties might be needed, too. See there.
+
+Example:
+
+	iic0: i2c@e6500000 {
+		compatible = "renesas,iic-r8a7790", "renesas,rcar-gen2-iic",
+			     "renesas,rmobile-iic";
+		reg = <0 0xe6500000 0 0x425>;
+		interrupts = <0 174 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp3_clks R8A7790_CLK_IIC0>;
+		clock-frequency = <400000>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-sirf.txt b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt
new file mode 100644
index 000000000..2701eefb0
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-sirf.txt
@@ -0,0 +1,19 @@
+I2C for SiRFprimaII platforms
+
+Required properties :
+- compatible : Must be "sirf,prima2-i2c"
+- reg: physical base address of the controller and length of memory mapped
+     region.
+- interrupts: interrupt number to the cpu.
+
+Optional properties:
+- clock-frequency : Constains desired I2C/HS-I2C bus clock frequency in Hz.
+  The absence of the property indicates the default frequency 100 kHz.
+
+Examples :
+
+i2c0: i2c@b00e0000 {
+    compatible = "sirf,prima2-i2c";
+    reg = <0xb00e0000 0x10000>;
+    interrupts = <24>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-sprd.txt b/Documentation/devicetree/bindings/i2c/i2c-sprd.txt
new file mode 100644
index 000000000..60b7cda15
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-sprd.txt
@@ -0,0 +1,31 @@
+I2C for Spreadtrum platforms
+
+Required properties:
+- compatible: Should be "sprd,sc9860-i2c".
+- reg: Specify the physical base address of the controller and length
+  of memory mapped region.
+- interrupts: Should contain I2C interrupt.
+- clock-names: Should contain following entries:
+  "i2c" for I2C clock,
+  "source" for I2C source (parent) clock,
+  "enable" for I2C module enable clock.
+- clocks: Should contain a clock specifier for each entry in clock-names.
+- clock-frequency: Constains desired I2C bus clock frequency in Hz.
+- #address-cells: Should be 1 to describe address cells for I2C device address.
+- #size-cells: Should be 0 means no size cell for I2C device address.
+
+Optional properties:
+- Child nodes conforming to I2C bus binding
+
+Examples:
+i2c0: i2c@70500000 {
+	compatible = "sprd,sc9860-i2c";
+	reg = <0 0x70500000 0 0x1000>;
+	interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+	clock-names = "i2c", "source", "enable";
+	clocks = <&clk_i2c3>, <&ext_26m>, <&clk_ap_apb_gates 11>;
+	clock-frequency = <400000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+};
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-st-ddci2c.txt b/Documentation/devicetree/bindings/i2c/i2c-st-ddci2c.txt
new file mode 100644
index 000000000..bd81a4826
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-st-ddci2c.txt
@@ -0,0 +1,15 @@
+ST Microelectronics DDC I2C
+
+Required properties :
+- compatible : Must be "st,ddci2c"
+- reg: physical base address of the controller and length of memory mapped
+     region.
+- interrupts: interrupt number to the cpu.
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
+
+Examples :
+
diff --git a/Documentation/devicetree/bindings/i2c/i2c-st.txt b/Documentation/devicetree/bindings/i2c/i2c-st.txt
new file mode 100644
index 000000000..4c26fda38
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-st.txt
@@ -0,0 +1,41 @@
+ST SSC binding, for I2C mode operation
+
+Required properties :
+- compatible : Must be "st,comms-ssc-i2c" or "st,comms-ssc4-i2c"
+- reg : Offset and length of the register set for the device
+- interrupts : the interrupt specifier
+- clock-names: Must contain "ssc".
+- clocks: Must contain an entry for each name in clock-names. See the common
+  clock bindings.
+- A pinctrl state named "default" must be defined to set pins in mode of
+  operation for I2C transfer.
+
+Optional properties :
+- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
+  the default 100 kHz frequency will be used. As only Normal and Fast modes
+  are supported, possible values are 100000 and 400000.
+- st,i2c-min-scl-pulse-width-us : The minimum valid SCL pulse width that is
+  allowed through the deglitch circuit. In units of us.
+- st,i2c-min-sda-pulse-width-us : The minimum valid SDA pulse width that is
+  allowed through the deglitch circuit. In units of us.
+- A pinctrl state named "idle" could be defined to set pins in idle state
+  when I2C instance is not performing a transfer.
+- A pinctrl state named "sleep" could be defined to set pins in sleep state
+  when driver enters in suspend.
+
+
+
+Example :
+
+i2c0: i2c@fed40000 {
+	compatible	= "st,comms-ssc4-i2c";
+	reg		= <0xfed40000 0x110>;
+	interrupts	=  <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
+	clocks		= <&clk_s_a0_ls CLK_ICN_REG>;
+	clock-names	= "ssc";
+	clock-frequency = <400000>;
+	pinctrl-names	= "default";
+	pinctrl-0	= <&pinctrl_i2c0_default>;
+	st,i2c-min-scl-pulse-width-us = <0>;
+	st,i2c-min-sda-pulse-width-us = <5>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-stm32.txt b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
new file mode 100644
index 000000000..3b5489966
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-stm32.txt
@@ -0,0 +1,56 @@
+* I2C controller embedded in STMicroelectronics STM32 I2C platform
+
+Required properties :
+- compatible : Must be one of the following
+  - "st,stm32f4-i2c"
+  - "st,stm32f7-i2c"
+- reg : Offset and length of the register set for the device
+- interrupts : Must contain the interrupt id for I2C event and then the
+  interrupt id for I2C error.
+- resets: Must contain the phandle to the reset controller.
+- clocks: Must contain the input clock of the I2C instance.
+- A pinctrl state named "default" must be defined to set pins in mode of
+  operation for I2C transfer
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties :
+- clock-frequency : Desired I2C bus clock frequency in Hz. If not specified,
+  the default 100 kHz frequency will be used.
+  For STM32F4 SoC Standard-mode and Fast-mode are supported, possible values are
+  100000 and 400000.
+  For STM32F7 SoC, Standard-mode, Fast-mode and Fast-mode Plus are supported,
+  possible values are 100000, 400000 and 1000000.
+- i2c-scl-rising-time-ns : Only for STM32F7, I2C SCL Rising time for the board
+  (default: 25)
+- i2c-scl-falling-time-ns : Only for STM32F7, I2C SCL Falling time for the board
+  (default: 10)
+  I2C Timings are derived from these 2 values
+
+Example :
+
+	i2c@40005400 {
+		compatible = "st,stm32f4-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x40005400 0x400>;
+		interrupts = <31>,
+			     <32>;
+		resets = <&rcc 277>;
+		clocks = <&rcc 0 149>;
+		pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
+		pinctrl-names = "default";
+	};
+
+	i2c@40005400 {
+		compatible = "st,stm32f7-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x40005400 0x400>;
+		interrupts = <31>,
+			     <32>;
+		resets = <&rcc STM32F7_APB1_RESET(I2C1)>;
+		clocks = <&rcc 1 CLK_I2C1>;
+		pinctrl-0 = <&i2c1_sda_pin>, <&i2c1_scl_pin>;
+		pinctrl-names = "default";
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt
new file mode 100644
index 000000000..49df00533
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-sunxi-p2wi.txt
@@ -0,0 +1,41 @@
+
+* Allwinner P2WI (Push/Pull 2 Wire Interface) controller
+
+Required properties :
+
+ - reg             : Offset and length of the register set for the device.
+ - compatible      : Should one of the following:
+                     - "allwinner,sun6i-a31-p2wi"
+ - interrupts      : The interrupt line connected to the P2WI peripheral.
+ - clocks          : The gate clk connected to the P2WI peripheral.
+ - resets          : The reset line connected to the P2WI peripheral.
+
+Optional properties :
+
+ - clock-frequency : Desired P2WI bus clock frequency in Hz. If not set the
+default frequency is 100kHz
+
+A P2WI may contain one child node encoding a P2WI slave device.
+
+Slave device properties:
+  Required properties:
+   - reg           : the I2C slave address used during the initialization
+                     process to switch from I2C to P2WI mode
+
+Example:
+
+	p2wi@1f03400 {
+		compatible = "allwinner,sun6i-a31-p2wi";
+		reg = <0x01f03400 0x400>;
+		interrupts = <0 39 4>;
+		clocks = <&apb0_gates 3>;
+		clock-frequency = <6000000>;
+		resets = <&apb0_rst 3>;
+
+		axp221: pmic@68 {
+			compatible = "x-powers,axp221";
+			reg = <0x68>;
+
+			/* ... */
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt b/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt
new file mode 100644
index 000000000..72f4a2f0f
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-synquacer.txt
@@ -0,0 +1,29 @@
+Socionext SynQuacer I2C
+
+Required properties:
+- compatible      : Must be "socionext,synquacer-i2c"
+- reg             : Offset and length of the register set for the device
+- interrupts      : A single interrupt specifier
+- #address-cells  : Must be <1>;
+- #size-cells     : Must be <0>;
+- clock-names     : Must contain "pclk".
+- clocks          : Must contain an entry for each name in clock-names.
+                    (See the common clock bindings.)
+
+Optional properties:
+- clock-frequency : Desired I2C bus clock frequency in Hz. As only Normal and
+                    Fast modes are supported, possible values are 100000 and
+                    400000.
+
+Example :
+
+    i2c@51210000 {
+        compatible = "socionext,synquacer-i2c";
+        reg = <0x51210000 0x1000>;
+        interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        clock-names = "pclk";
+        clocks = <&clk_i2c>;
+        clock-frequency = <400000>;
+    };
diff --git a/Documentation/devicetree/bindings/i2c/i2c-uniphier-f.txt b/Documentation/devicetree/bindings/i2c/i2c-uniphier-f.txt
new file mode 100644
index 000000000..27fc6f8c7
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-uniphier-f.txt
@@ -0,0 +1,25 @@
+UniPhier I2C controller (FIFO-builtin)
+
+Required properties:
+- compatible: should be "socionext,uniphier-fi2c".
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+- reg: offset and length of the register set for the device.
+- interrupts: a single interrupt specifier.
+- clocks: phandle to the input clock.
+
+Optional properties:
+- clock-frequency: desired I2C bus frequency in Hz.  The maximum supported
+  value is 400000.  Defaults to 100000 if not specified.
+
+Examples:
+
+	i2c0: i2c@58780000 {
+		compatible = "socionext,uniphier-fi2c";
+		reg = <0x58780000 0x80>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <0 41 4>;
+		clocks = <&i2c_clk>;
+		clock-frequency = <100000>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-uniphier.txt b/Documentation/devicetree/bindings/i2c/i2c-uniphier.txt
new file mode 100644
index 000000000..26f9d95b3
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-uniphier.txt
@@ -0,0 +1,25 @@
+UniPhier I2C controller (FIFO-less)
+
+Required properties:
+- compatible: should be "socionext,uniphier-i2c".
+- #address-cells: should be 1.
+- #size-cells: should be 0.
+- reg: offset and length of the register set for the device.
+- interrupts: a single interrupt specifier.
+- clocks: phandle to the input clock.
+
+Optional properties:
+- clock-frequency: desired I2C bus frequency in Hz.  The maximum supported
+  value is 400000.  Defaults to 100000 if not specified.
+
+Examples:
+
+	i2c0: i2c@58400000 {
+		compatible = "socionext,uniphier-i2c";
+		reg = <0x58400000 0x40>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts = <0 41 1>;
+		clocks = <&i2c_clk>;
+		clock-frequency = <100000>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-versatile.txt b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt
new file mode 100644
index 000000000..361d31c51
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-versatile.txt
@@ -0,0 +1,10 @@
+i2c Controller on ARM Versatile platform:
+
+Required properties:
+- compatible : Must be "arm,versatile-i2c";
+- reg
+- #address-cells = <1>;
+- #size-cells = <0>;
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
diff --git a/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt b/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt
new file mode 100644
index 000000000..94a425eaa
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-vt8500.txt
@@ -0,0 +1,24 @@
+* Wondermedia I2C Controller
+
+Required properties :
+
+ - compatible : should be "wm,wm8505-i2c"
+ - reg : Offset and length of the register set for the device
+ - interrupts : <IRQ> where IRQ is the interrupt number
+ - clocks : phandle to the I2C clock source
+
+Optional properties :
+
+ - clock-frequency : desired I2C bus clock frequency in Hz.
+	Valid values are 100000 and 400000.
+	Default to 100000 if not specified, or invalid value.
+
+Example :
+
+	i2c_0: i2c@d8280000 {
+		compatible = "wm,wm8505-i2c";
+		reg = <0xd8280000 0x1000>;
+		interrupts = <19>;
+		clocks = <&clki2c0>;
+		clock-frequency = <400000>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt b/Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt
new file mode 100644
index 000000000..f6b2c20cf
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-xgene-slimpro.txt
@@ -0,0 +1,15 @@
+APM X-Gene SLIMpro Mailbox I2C Driver
+
+An I2C controller accessed over the "SLIMpro" mailbox.
+
+Required properties :
+
+ - compatible : should be "apm,xgene-slimpro-i2c"
+ - mboxes : use the label reference for the mailbox as the first parameter.
+	    The second parameter is the channel number.
+
+Example :
+	i2cslimpro {
+		compatible = "apm,xgene-slimpro-i2c";
+		mboxes = <&mailbox 0>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-xiic.txt b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt
new file mode 100644
index 000000000..caf42e989
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-xiic.txt
@@ -0,0 +1,25 @@
+Xilinx IIC controller:
+
+Required properties:
+- compatible : Must be "xlnx,xps-iic-2.00.a"
+- reg : IIC register location and length
+- interrupts : IIC controller unterrupt
+- #address-cells = <1>
+- #size-cells = <0>
+- clocks: Input clock specifier. Refer to common clock bindings.
+
+Optional properties:
+- Child nodes conforming to i2c bus binding
+- clock-names: Input clock name, should be 'pclk'.
+
+Example:
+
+	axi_iic_0: i2c@40800000 {
+		compatible = "xlnx,xps-iic-2.00.a";
+		clocks = <&clkc 15>;
+		interrupts = < 1 2 >;
+		reg = < 0x40800000 0x10000 >;
+
+		#size-cells = <0>;
+		#address-cells = <1>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt b/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt
new file mode 100644
index 000000000..f818ef507
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-xlp9xx.txt
@@ -0,0 +1,22 @@
+Device tree configuration for the I2C controller on the XLP9xx/5xx SoC
+
+Required properties:
+- compatible      : should be "netlogic,xlp980-i2c"
+- reg             : bus address start and address range size of device
+- interrupts      : interrupt number
+
+Optional properties:
+- clock-frequency : frequency of bus clock in Hz
+                    Defaults to 100 KHz when the property is not specified
+
+Example:
+
+i2c0: i2c@113100 {
+	compatible = "netlogic,xlp980-i2c";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0 0x113100 0x100>;
+	clock-frequency = <400000>;
+	interrupts = <30>;
+	interrupt-parent = <&pic>;
+};
diff --git a/Documentation/devicetree/bindings/i2c/i2c-zx2967.txt b/Documentation/devicetree/bindings/i2c/i2c-zx2967.txt
new file mode 100644
index 000000000..cb806d1ae
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c-zx2967.txt
@@ -0,0 +1,22 @@
+ZTE zx2967 I2C controller
+
+Required properties:
+ - compatible: must be "zte,zx296718-i2c"
+ - reg: physical address and length of the device registers
+ - interrupts: a single interrupt specifier
+ - clocks: clock for the device
+ - #address-cells: should be <1>
+ - #size-cells: should be <0>
+ - clock-frequency: the desired I2C bus clock frequency.
+
+Examples:
+
+	i2c@112000 {
+		compatible = "zte,zx296718-i2c";
+		reg = <0x00112000 0x1000>;
+		interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&osc24m>;
+		#address-cells = <1>
+		#size-cells = <0>;
+		clock-frequency = <1600000>;
+	};
diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt
new file mode 100644
index 000000000..112639824
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/i2c.txt
@@ -0,0 +1,94 @@
+Generic device tree bindings for I2C busses
+===========================================
+
+This document describes generic bindings which can be used to describe I2C
+busses in a device tree.
+
+Required properties
+-------------------
+
+- #address-cells  - should be <1>. Read more about addresses below.
+- #size-cells     - should be <0>.
+- compatible      - name of I2C bus controller following generic names
+		    recommended practice.
+
+For other required properties e.g. to describe register sets,
+clocks, etc. check the binding documentation of the specific driver.
+
+The cells properties above define that an address of children of an I2C bus
+are described by a single value. This is usually a 7 bit address. However,
+flags can be attached to the address. I2C_TEN_BIT_ADDRESS is used to mark a 10
+bit address. It is needed to avoid the ambiguity between e.g. a 7 bit address
+of 0x50 and a 10 bit address of 0x050 which, in theory, can be on the same bus.
+Another flag is I2C_OWN_SLAVE_ADDRESS to mark addresses on which we listen to
+be devices ourselves.
+
+Optional properties
+-------------------
+
+These properties may not be supported by all drivers. However, if a driver
+wants to support one of the below features, it should adapt the bindings below.
+
+- clock-frequency
+	frequency of bus clock in Hz.
+
+- i2c-bus
+	For I2C adapters that have child nodes that are a mixture of both I2C
+	devices and non-I2C devices, the 'i2c-bus' subnode can be used for
+	populating I2C devices. If the 'i2c-bus' subnode is present, only
+	subnodes of this will be considered as I2C slaves. The properties,
+	'#address-cells' and '#size-cells' must be defined under this subnode
+	if present.
+
+- i2c-scl-falling-time-ns
+	Number of nanoseconds the SCL signal takes to fall; t(f) in the I2C
+	specification.
+
+- i2c-scl-internal-delay-ns
+	Number of nanoseconds the IP core additionally needs to setup SCL.
+
+- i2c-scl-rising-time-ns
+	Number of nanoseconds the SCL signal takes to rise; t(r) in the I2C
+	specification.
+
+- i2c-sda-falling-time-ns
+	Number of nanoseconds the SDA signal takes to fall; t(f) in the I2C
+	specification.
+
+- interrupts
+	interrupts used by the device.
+
+- interrupt-names
+	"irq", "wakeup" and "smbus_alert" names are recognized by I2C core,
+	other names are	left to individual drivers.
+
+- host-notify
+	device uses SMBus host notify protocol instead of interrupt line.
+
+- multi-master
+	states that there is another master active on this bus. The OS can use
+	this information to adapt power management to keep the arbitration awake
+	all the time, for example.
+
+- wakeup-source
+	device can be used as a wakeup source.
+
+- reg
+	I2C slave addresses
+
+- reg-names
+	Names of map programmable addresses.
+	It can contain any map needing another address than default one.
+
+Binding may contain optional "interrupts" property, describing interrupts
+used by the device. I2C core will assign "irq" interrupt (or the very first
+interrupt if not using interrupt names) as primary interrupt for the slave.
+
+Alternatively, devices supporting SMbus Host Notify, and connected to
+adapters that support this feature, may use "host-notify" property. I2C
+core will create a virtual interrupt for Host Notify and assign it as
+primary interrupt for the slave.
+
+Also, if device is marked as a wakeup source, I2C core will set up "wakeup"
+interrupt for the device. If "wakeup" interrupt name is not present in the
+binding, then primary interrupt will be used as wakeup interrupt.
diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt
new file mode 100644
index 000000000..ab240e10d
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra186-bpmp-i2c.txt
@@ -0,0 +1,42 @@
+NVIDIA Tegra186 BPMP I2C controller
+
+In Tegra186, the BPMP (Boot and Power Management Processor) owns certain HW
+devices, such as the I2C controller for the power management I2C bus. Software
+running on other CPUs must perform IPC to the BPMP in order to execute
+transactions on that I2C bus. This binding describes an I2C bus that is
+accessed in such a fashion.
+
+The BPMP I2C node must be located directly inside the main BPMP node. See
+../firmware/nvidia,tegra186-bpmp.txt for details of the BPMP binding.
+
+This node represents an I2C controller. See ../i2c/i2c.txt for details of the
+core I2C binding.
+
+Required properties:
+- compatible:
+    Array of strings.
+    One of:
+    - "nvidia,tegra186-bpmp-i2c".
+- #address-cells: Address cells for I2C device address.
+    Single-cell integer.
+    Must be <1>.
+- #size-cells:
+    Single-cell integer.
+    Must be <0>.
+- nvidia,bpmp-bus-id:
+    Single-cell integer.
+    Indicates the I2C bus number this DT node represent, as defined by the
+    BPMP firmware.
+
+Example:
+
+bpmp {
+	...
+
+	i2c {
+		compatible = "nvidia,tegra186-bpmp-i2c";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		nvidia,bpmp-bus-id = <5>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt
new file mode 100644
index 000000000..f64064f8b
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/nvidia,tegra20-i2c.txt
@@ -0,0 +1,74 @@
+NVIDIA Tegra20/Tegra30/Tegra114 I2C controller driver.
+
+Required properties:
+- compatible : For Tegra20, must be one of "nvidia,tegra20-i2c-dvc" or
+  "nvidia,tegra20-i2c".  For Tegra30, must be "nvidia,tegra30-i2c".
+  For Tegra114, must be "nvidia,tegra114-i2c".  Otherwise, must be
+  "nvidia,<chip>-i2c", plus at least one of the above, where <chip> is
+  tegra124, tegra132, or tegra210.
+  Details of compatible are as follows:
+  nvidia,tegra20-i2c-dvc: Tegra20 has specific I2C controller called as DVC I2C
+	controller. This only support master mode of I2C communication. Register
+	interface/offset and interrupts handling are different than generic I2C
+	controller. Driver of DVC I2C controller is only compatible with
+	"nvidia,tegra20-i2c-dvc".
+  nvidia,tegra20-i2c: Tegra20 has 4 generic I2C controller. This can support
+	master and slave mode of I2C communication. The i2c-tegra driver only
+	support master mode of I2C communication. Driver of I2C controller is
+	only compatible with "nvidia,tegra20-i2c".
+  nvidia,tegra30-i2c: Tegra30 has 5 generic I2C controller. This controller is
+	very much similar to Tegra20 I2C controller with additional feature:
+	Continue Transfer Support. This feature helps to implement M_NO_START
+	as per I2C core API transfer flags. Driver of I2C controller is
+	compatible with "nvidia,tegra30-i2c" to enable the continue transfer
+	support. This is also compatible with "nvidia,tegra20-i2c" without
+	continue transfer support.
+  nvidia,tegra114-i2c: Tegra114 has 5 generic I2C controller. This controller is
+	very much similar to Tegra30 I2C controller with some hardware
+	modification:
+	 - Tegra30/Tegra20 I2C controller has 2 clock source called div-clk and
+	   fast-clk. Tegra114 has only one clock source called as div-clk and
+	   hence clock mechanism is changed in I2C controller.
+	 - Tegra30/Tegra20 I2C controller has enabled per packet transfer by
+	   default and there is no way to disable it. Tegra114 has this
+	   interrupt disable by default and SW need to enable explicitly.
+	Due to above changes, Tegra114 I2C driver makes incompatible with
+	previous hardware driver. Hence, tegra114 I2C controller is compatible
+	with "nvidia,tegra114-i2c".
+- reg: Should contain I2C controller registers physical address and length.
+- interrupts: Should contain I2C controller interrupts.
+- address-cells: Address cells for I2C device address.
+- size-cells: Size of the I2C device address.
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  Tegra20/Tegra30:
+  - div-clk
+  - fast-clk
+  Tegra114:
+  - div-clk
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - i2c
+- dmas: Must contain an entry for each entry in clock-names.
+  See ../dma/dma.txt for details.
+- dma-names: Must include the following entries:
+  - rx
+  - tx
+
+Example:
+
+	i2c@7000c000 {
+		compatible = "nvidia,tegra20-i2c";
+		reg = <0x7000c000 0x100>;
+		interrupts = <0 38 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&tegra_car 12>, <&tegra_car 124>;
+		clock-names = "div-clk", "fast-clk";
+		resets = <&tegra_car 12>;
+		reset-names = "i2c";
+		dmas = <&apbdma 16>, <&apbdma 16>;
+		dma-names = "rx", "tx";
+	};
diff --git a/Documentation/devicetree/bindings/i2c/nxp,pca9541.txt b/Documentation/devicetree/bindings/i2c/nxp,pca9541.txt
new file mode 100644
index 000000000..0fbbc6970
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/nxp,pca9541.txt
@@ -0,0 +1,29 @@
+* NXP PCA9541 I2C bus master selector
+
+Required Properties:
+
+  - compatible: Must be "nxp,pca9541"
+
+  - reg: The I2C address of the device.
+
+  The following required properties are defined externally:
+
+  - I2C arbitration bus node. See i2c-arb.txt in this directory.
+
+
+Example:
+
+	i2c-arbitrator@74 {
+		compatible = "nxp,pca9541";
+		reg = <0x74>;
+
+		i2c-arb {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			eeprom@54 {
+				compatible = "at,24c08";
+				reg = <0x54>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
new file mode 100644
index 000000000..dc71754a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
@@ -0,0 +1,40 @@
+Qualcomm Universal Peripheral (QUP) I2C controller
+
+Required properties:
+ - compatible: Should be:
+   * "qcom,i2c-qup-v1.1.1" for 8660, 8960 and 8064.
+   * "qcom,i2c-qup-v2.1.1" for 8974 v1.
+   * "qcom,i2c-qup-v2.2.1" for 8974 v2 and later.
+ - reg: Should contain QUP register address and length.
+ - interrupts: Should contain I2C interrupt.
+
+ - clocks: A list of phandles + clock-specifiers, one for each entry in
+   clock-names.
+ - clock-names: Should contain:
+   * "core" for the core clock
+   * "iface" for the AHB clock
+
+ - #address-cells: Should be <1> Address cells for i2c device address
+ - #size-cells: Should be <0> as i2c addresses have no size component
+
+Optional properties:
+ - clock-frequency: Should specify the desired i2c bus clock frequency in Hz,
+                    defaults to 100kHz if omitted.
+
+Child nodes should conform to i2c bus binding.
+
+Example:
+
+ i2c@f9924000 {
+ 	compatible = "qcom,i2c-qup-v2.2.1";
+ 	reg = <0xf9924000 0x1000>;
+ 	interrupts = <0 96 0>;
+
+ 	clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+ 	clock-names = "core", "iface";
+
+ 	clock-frequency = <355000>;
+
+ 	#address-cells = <1>;
+ 	#size-cells = <0>;
+ };