Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

4 files changed, 74 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/iio/humidity/dht11.txt b/Documentation/devicetree/bindings/iio/humidity/dht11.txt
new file mode 100644
index 000000000..ecc24c199
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/humidity/dht11.txt
@@ -0,0 +1,14 @@
+* DHT11 humidity/temperature sensor (and compatibles like DHT22)
+
+Required properties:
+  - compatible: Should be "dht11"
+  - gpios: Should specify the GPIO connected to the sensor's data
+    line, see "gpios property" in
+    Documentation/devicetree/bindings/gpio/gpio.txt.
+
+Example:
+
+humidity_sensor {
+	compatible = "dht11";
+	gpios = <&gpio0 6 0>;
+}
diff --git a/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt b/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt
new file mode 100644
index 000000000..c52333bdf
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/humidity/hdc100x.txt
@@ -0,0 +1,17 @@
+* HDC100x temperature + humidity sensors
+
+Required properties:
+  - compatible: Should contain one of the following:
+	ti,hdc1000
+	ti,hdc1008
+	ti,hdc1010
+	ti,hdc1050
+	ti,hdc1080
+  - reg: i2c address of the sensor
+
+Example:
+
+hdc100x@40 {
+	compatible = "ti,hdc1000";
+	reg = <0x40>;
+};
diff --git a/Documentation/devicetree/bindings/iio/humidity/hts221.txt b/Documentation/devicetree/bindings/iio/humidity/hts221.txt
new file mode 100644
index 000000000..84d029372
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/humidity/hts221.txt
@@ -0,0 +1,30 @@
+* HTS221 STM humidity + temperature sensor
+
+Required properties:
+- compatible: should be "st,hts221"
+- reg: i2c address of the sensor / spi cs line
+
+Optional properties:
+- drive-open-drain: the interrupt/data ready line will be configured
+  as open drain, which is useful if several sensors share the same
+  interrupt line. This is a boolean property.
+  If the requested interrupt is configured as IRQ_TYPE_LEVEL_HIGH or
+  IRQ_TYPE_EDGE_RISING a pull-down resistor is needed to drive the line
+  when it is not active, whereas a pull-up one is needed when interrupt
+  line is configured as IRQ_TYPE_LEVEL_LOW or IRQ_TYPE_EDGE_FALLING.
+  Refer to pinctrl/pinctrl-bindings.txt for the property description.
+- interrupts: interrupt mapping for IRQ. It should be configured with
+  flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or
+  IRQ_TYPE_EDGE_FALLING.
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt
+  client node bindings.
+
+Example:
+
+hts221@5f {
+	compatible = "st,hts221";
+	reg = <0x5f>;
+	interrupt-parent = <&gpio0>;
+	interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+};
diff --git a/Documentation/devicetree/bindings/iio/humidity/htu21.txt b/Documentation/devicetree/bindings/iio/humidity/htu21.txt
new file mode 100644
index 000000000..97d79636f
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/humidity/htu21.txt
@@ -0,0 +1,13 @@
+*HTU21 - Measurement-Specialties htu21 temperature & humidity sensor and humidity part of MS8607 sensor
+
+Required properties:
+
+	- compatible: should be "meas,htu21" or "meas,ms8607-humidity"
+	- reg: I2C address of the sensor
+
+Example:
+
+htu21@40 {
+	compatible = "meas,htu21";
+	reg = <0x40>;
+};