Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

13 files changed, 321 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/iio/light/apds9300.txt b/Documentation/devicetree/bindings/iio/light/apds9300.txt
new file mode 100644
index 000000000..aa199e09a
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/apds9300.txt
@@ -0,0 +1,21 @@
+* Avago APDS9300 ambient light sensor
+
+http://www.avagotech.com/docs/AV02-1077EN
+
+Required properties:
+
+  - compatible : should be "avago,apds9300"
+  - reg : the I2C address of the sensor
+
+Optional properties:
+
+  - interrupts : interrupt mapping for GPIO IRQ
+
+Example:
+
+apds9300@39 {
+	compatible = "avago,apds9300";
+	reg = <0x39>;
+	interrupt-parent = <&gpio2>;
+	interrupts = <29 8>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/apds9960.txt b/Documentation/devicetree/bindings/iio/light/apds9960.txt
new file mode 100644
index 000000000..3af325ad1
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/apds9960.txt
@@ -0,0 +1,21 @@
+* Avago APDS9960 gesture/RGB/ALS/proximity sensor
+
+http://www.avagotech.com/docs/AV02-4191EN
+
+Required properties:
+
+  - compatible: must be "avago,apds9960"
+  - reg: the I2c address of the sensor
+  - interrupts : the sole interrupt generated by the device
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client
+  node bindings.
+
+Example:
+
+apds9960@39 {
+	compatible = "avago,apds9960";
+	reg = <0x39>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 1>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/cm3605.txt b/Documentation/devicetree/bindings/iio/light/cm3605.txt
new file mode 100644
index 000000000..56331a79f
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/cm3605.txt
@@ -0,0 +1,41 @@
+Capella Microsystems CM3605
+Ambient Light and Short Distance Proximity Sensor
+
+The CM3605 is an entirely analog part which however require quite a bit of
+software logic to interface a host operating system.
+
+This ALS and proximity sensor was one of the very first deployed in mobile
+handsets, notably it is used in the very first Nexus One Android phone from
+2010.
+
+Required properties:
+- compatible: must be: "capella,cm3605"
+- aset-gpios: GPIO line controlling the ASET line (drive low
+  to activate the ALS, should be flagged GPIO_ACTIVE_LOW)
+- interrupts: the IRQ line (such as a GPIO) that is connected to
+  the POUT (proximity sensor out) line. The edge detection must
+  be set to IRQ_TYPE_EDGE_BOTH so as to detect movements toward
+  and away from the proximity sensor.
+- io-channels: the ADC channel used for converting the voltage from
+  AOUT to a digital representation.
+- io-channel-names: must be "aout"
+
+Optional properties:
+- vdd-supply: regulator supplying VDD power to the component.
+- capella,aset-resistance-ohms: the sensitivity calibration resistance,
+  in Ohms. Valid values are: 50000, 100000, 300000 and 600000,
+  as these are the resistance values that we are supplied with
+  calibration curves for. If not supplied, 100 kOhm will be assumed
+  but it is strongly recommended to supply this.
+
+Example:
+
+cm3605 {
+	compatible = "capella,cm3605";
+	vdd-supply = <&foo_reg>;
+	aset-gpios = <&foo_gpio 1 GPIO_ACTIVE_LOW>;
+	capella,aset-resistance-ohms = <100000>;
+	interrupts = <1 IRQ_TYPE_EDGE_BOTH>;
+	io-channels = <&adc 0x01>;
+	io-channel-names = "aout";
+};
diff --git a/Documentation/devicetree/bindings/iio/light/cm36651.txt b/Documentation/devicetree/bindings/iio/light/cm36651.txt
new file mode 100644
index 000000000..c03e19db4
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/cm36651.txt
@@ -0,0 +1,26 @@
+* Capella CM36651 I2C Proximity and Color Light sensor
+
+Required properties:
+- compatible: must be "capella,cm36651"
+- reg: the I2C address of the device
+- interrupts: interrupt-specifier for the sole interrupt
+	      generated by the device
+- vled-supply: regulator for the IR LED. IR_LED is a part
+	      of the cm36651 for proximity detection.
+	      As covered in ../../regulator/regulator.txt
+
+Example:
+
+	i2c_cm36651: i2c-gpio {
+		/* ... */
+
+		cm36651@18 {
+			compatible = "capella,cm36651";
+			reg = <0x18>;
+			interrupt-parent = <&gpx0>;
+			interrupts = <2 0>;
+			vled-supply = <&ps_als_reg>;
+		};
+
+		/* ... */
+	};
diff --git a/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt b/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt
new file mode 100644
index 000000000..9231c8231
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/gp2ap020a00f.txt
@@ -0,0 +1,21 @@
+* Sharp GP2AP020A00F I2C Proximity/ALS sensor
+
+The proximity detector sensor requires power supply
+for its built-in led. It is also defined by this binding.
+
+Required properties:
+
+  - compatible : should be "sharp,gp2ap020a00f"
+  - reg : the I2C slave address of the light sensor
+  - interrupts : interrupt specifier for the sole interrupt generated
+		 by the device
+  - vled-supply : VLED power supply, as covered in ../regulator/regulator.txt
+
+Example:
+
+gp2ap020a00f@39 {
+	compatible = "sharp,gp2ap020a00f";
+	reg = <0x39>;
+	interrupts = <2 0>;
+	vled-supply = <...>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/isl29018.txt b/Documentation/devicetree/bindings/iio/light/isl29018.txt
new file mode 100644
index 000000000..b9bbde3e1
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/isl29018.txt
@@ -0,0 +1,27 @@
+* ISL 29018/29023/29035 I2C ALS, Proximity, and Infrared sensor
+
+Required properties:
+
+  - compatible: Should be one of
+		"isil,isl29018"
+		"isil,isl29023"
+		"isil,isl29035"
+  - reg: the I2C address of the device
+
+Optional properties:
+
+  - interrupts: the sole interrupt generated by the device
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client
+  node bindings.
+
+  - vcc-supply: phandle to the regulator that provides power to the sensor.
+
+Example:
+
+isl29018@44 {
+	compatible = "isil,isl29018";
+	reg = <0x44>;
+	interrupt-parent = <&gpio>;
+	interrupts = <TEGRA_GPIO(Z, 2) IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/isl29501.txt b/Documentation/devicetree/bindings/iio/light/isl29501.txt
new file mode 100644
index 000000000..46957997f
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/isl29501.txt
@@ -0,0 +1,13 @@
+* ISL29501 Time-of-flight sensor.
+
+Required properties:
+
+  - compatible : should be "renesas,isl29501"
+  - reg : the I2C address of the sensor
+
+Example:
+
+isl29501@57 {
+	compatible = "renesas,isl29501";
+	reg = <0x57>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/opt3001.txt b/Documentation/devicetree/bindings/iio/light/opt3001.txt
new file mode 100644
index 000000000..47b13eb8f
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/opt3001.txt
@@ -0,0 +1,25 @@
+* Texas Instruments OPT3001 Ambient Light Sensor
+
+The driver supports interrupt-driven and interrupt-less operation, depending
+on whether an interrupt property has been populated into the DT. Note that
+the optional generation of IIO events on rising/falling light threshold changes
+requires the use of interrupts. Without interrupts, only the simple reading
+of the current light value is supported through the IIO API.
+
+http://www.ti.com/product/opt3001
+
+Required properties:
+  - compatible: should be "ti,opt3001"
+  - reg: the I2C address of the sensor
+
+Optional properties:
+  - interrupts: interrupt mapping for GPIO IRQ (configure for falling edge)
+
+Example:
+
+opt3001@44 {
+	compatible = "ti,opt3001";
+	reg = <0x44>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/tsl2563.txt b/Documentation/devicetree/bindings/iio/light/tsl2563.txt
new file mode 100644
index 000000000..f91e809e7
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/tsl2563.txt
@@ -0,0 +1,19 @@
+* AMS TAOS TSL2563 ambient light sensor
+
+Required properties:
+
+  - compatible : should be "amstaos,tsl2563"
+  - reg : the I2C address of the sensor
+
+Optional properties:
+
+  - amstaos,cover-comp-gain : integer used as multiplier for gain
+                              compensation (default = 1)
+
+Example:
+
+tsl2563@29 {
+	compatible = "amstaos,tsl2563";
+	reg = <0x29>;
+	amstaos,cover-comp-gain = <16>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/tsl2583.txt b/Documentation/devicetree/bindings/iio/light/tsl2583.txt
new file mode 100644
index 000000000..059dffa18
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/tsl2583.txt
@@ -0,0 +1,25 @@
+* TAOS TSL 2580/2581/2583 ALS sensor
+
+Required properties:
+
+  - compatible: Should be one of
+		"amstaos,tsl2580"
+		"amstaos,tsl2581"
+		"amstaos,tsl2583"
+  - reg: the I2C address of the device
+
+Optional properties:
+
+  - interrupts: the sole interrupt generated by the device
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt client
+  node bindings.
+
+  - vcc-supply: phandle to the regulator that provides power to the sensor.
+
+Example:
+
+tsl2581@29 {
+	compatible = "amstaos,tsl2581";
+	reg = <0x29>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/us5182d.txt b/Documentation/devicetree/bindings/iio/light/us5182d.txt
new file mode 100644
index 000000000..a61979997
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/us5182d.txt
@@ -0,0 +1,45 @@
+* UPISEMI us5182d I2C ALS and Proximity sensor
+
+Required properties:
+- compatible: must be "upisemi,usd5182"
+- reg: the I2C address of the device
+
+Optional properties:
+- upisemi,glass-coef: glass attenuation factor - compensation factor of
+                      resolution 1000 for material transmittance.
+
+- upisemi,dark-ths: array of 8 elements containing 16-bit thresholds (adc
+                    counts) corresponding to every scale.
+
+- upisemi,upper-dark-gain: 8-bit dark gain compensation factor(4 int and 4
+                           fractional bits - Q4.4) applied when light > threshold
+
+- upisemi,lower-dark-gain: 8-bit dark gain compensation factor(4 int and 4
+                           fractional bits - Q4.4) applied when light < threshold
+
+- upisemi,continuous: This chip has two power modes: one-shot (chip takes one
+                      measurement and then shuts itself down) and continuous (
+                      chip takes continuous measurements). The one-shot mode is
+                      more power-friendly but the continuous mode may be more
+                      reliable. If this property is specified the continuous
+                      mode will be used instead of the default one-shot one for
+                      raw reads.
+
+If the optional properties are not specified these factors will default to the
+values in the below example.
+The glass-coef defaults to no compensation for the covering material.
+The threshold array defaults to experimental values that work with US5182D
+sensor on evaluation board - roughly between 12-32 lux.
+There will be no dark-gain compensation by default when ALS > thresh
+(0 * dark-gain), and a 1.35 compensation factor when ALS < thresh.
+
+Example:
+
+    usd5182@39 {
+                compatible = "upisemi,usd5182";
+                reg = <0x39>;
+                upisemi,glass-coef = < 1000 >;
+                upisemi,dark-ths = /bits/ 16 <170 200 512 512 800 2000 4000 8000>;
+                upisemi,upper-dark-gain = /bits/ 8 <0x00>;
+                upisemi,lower-dark-gain = /bits/ 8 <0x16>;
+    };
diff --git a/Documentation/devicetree/bindings/iio/light/uvis25.txt b/Documentation/devicetree/bindings/iio/light/uvis25.txt
new file mode 100644
index 000000000..043c139d9
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/uvis25.txt
@@ -0,0 +1,22 @@
+* ST UVIS25 uv sensor
+
+Required properties:
+- compatible: should be "st,uvis25"
+- reg: i2c address of the sensor / spi cs line
+
+Optional properties:
+- interrupts: interrupt mapping for IRQ. It should be configured with
+  flags IRQ_TYPE_LEVEL_HIGH, IRQ_TYPE_EDGE_RISING, IRQ_TYPE_LEVEL_LOW or
+  IRQ_TYPE_EDGE_FALLING.
+
+  Refer to interrupt-controller/interrupts.txt for generic interrupt
+  client node bindings.
+
+Example:
+
+uvis25@47 {
+	compatible = "st,uvis25";
+	reg = <0x47>;
+	interrupt-parent = <&gpio0>;
+	interrupts = <0 IRQ_TYPE_EDGE_RISING>;
+};
diff --git a/Documentation/devicetree/bindings/iio/light/vl6180.txt b/Documentation/devicetree/bindings/iio/light/vl6180.txt
new file mode 100644
index 000000000..2c5295271
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/light/vl6180.txt
@@ -0,0 +1,15 @@
+STMicro VL6180 -  ALS, range and proximity sensor
+
+Link to datasheet: http://www.st.com/resource/en/datasheet/vl6180x.pdf
+
+Required properties:
+
+	-compatible: should be "st,vl6180"
+	-reg: the I2C address of the sensor
+
+Example:
+
+vl6180@29 {
+	compatible = "st,vl6180";
+	reg = <0x29>;
+};